JUNCTION BOX & PULL BOX (TYP.

) BUNDLE 2 R2 #5 OR 2 R9 #5
THRIE BEAM FOR SIZE & LOCATION, SEE ADJACENT TO EACH END OF
OR W-BEAM 2 ~ 10' STEEL JUNCTION BOX TABLE JUNCTION BOX (TYP.)
END OF BRIDGE OR WALL 7 CURB LINE
GUARDRAIL CONDUITS
2 ~ STAINLESS STEEL
TS LT MOUNTING TABS (TOP & BOT.)
8" x 8" x 18" JUNCTION BOX 7

20'-0" MAX. CONDUIT DEFLECTION FITTING A

2 STEEL CONDUIT TO PVC ADAPTORS TRAFFIC BARRIER
WITH INTERNAL BONDING JUMPER.
2'-0"

5'-0" MIN. IN STATIONARY FORM BARRIER WHERE

SEE DETAIL THIS SHEET CONDUIT EXPANSION FITTING
PVC PIPE INSTALLED IN BARRIER
(TYP. AT EXPANSION JOINT)
TS LT É"ø POLYETHYLENE

2'-0"
JUNCTION BOX SIZED PLAN OR COPPER PIPE DRAIN
PER ELECTRICAL PLANS.
LABEL JUNCTION BOX LIDS CONDUITS & J-BOX IN TRAFFIC BARRIER
AS SHOWN (TYP.)

A
NOTE TO DESIGNERS
MODIFY THE FOLLOWING TO MATCH PROJECT REQUIREMENTS:
1. BARRIER END SECTION. ¢ J-BOX & BARRIER PANEL ¢ J-BOX & BARRIER PANEL SECTION A
2. REMOVE GUARDRAIL IF NOT CONNECTED TO BRIDGE ITEM.
3. CONDUIT ALIGNMENT 200'-0" MAX.

¢ J-BOX & BARRIER PANEL ¢ J-BOX & BARRIER PANEL

200'-0" MAX. 8 EXPANSION JOINT
5 10'-0" STEEL CONDUIT SECTION SECURE CONDUIT AND BUNDLE 2 R1 #5, 2 R2 #5 OR CONDUIT EXPANSION
BETWEEN CONDUIT DEFLECTION BOX TO REBAR TO 2 R9 #5 ADJACENT TO EACH 8'-0" MIN. (L TYP.) CONDUIT PIPE SIZED
#4 x 3'-6" (TYP.) FITTING
FITTING A AND PVC CONDUIT IN PREVENT MOVEMENT END OF JUNCTION BOX (TYP.) PER WIRING SCHEDULE
STATIONARY FORM BARRIER L (TYP.)

¾"
STEEL CONDUIT,
INCLUDING TS LT TS LT
Last revised on :

ELBOWS AND
SWEEPS
BONDING JUMPER
1" TIES ~ SPACE @ 2½" MAX. 1"

BLOCKOUT FOR STEEL CONDUIT TO PVC ADAPTOR IN TOP OF BRIDGE DECK 2"ø CONDUIT PIPES OR CONDUIT EXPANSION FITTING
CONDUITS STATIONARY FORM BARRIER WHERE AT CURB LINE SIZE CONDUIT PER CONDUIT FITTING - (TYPE AX FOR MOVEMENT OF ± 2")
PVC PIPE INSTALLED IN BARRIER 6 WIRING SCHEDULE
NOTES:
09/25/2020

CONDUIT DEFLECTION AT BRIDGE EXPANSION JOINTS

FITTING A
STEEL CONDUIT SECTION ELEVATION 1 WHERE CONDUIT IN A STRUCTURE IS ROUTED ACROSS A JOINT, WRAP STEEL CONDUIT PIPE FOR
BETWEEN CONDUIT DEFLECTION 1'-0" ON EACH SIDE OF JOINT. PIPE WRAP TAPE SHALL BE 2" WIDE, 20 MIL THICK, AND
FITTING A AND JUNCTION BOX CONDUITS & J-BOX IN TRAFFIC BARRIER INSTALLED WITH A MINIMUM OF 1" OVERLAP.
4
2 PLACE AT CONDUIT PIPE EXIT FROM STRUCTURE AND SHALL BE IN NEUTRAL STATE AFTER
½" PREMOLDED JOINT FILLER INSTALLATION.
SEE STANDARD PLANS
1 3 CONDUIT PIPES PLACED THROUGH RETAINING WALL TRAFFIC BARRIER SHALL
CONCRETE CONCRETE
BE FITTED WITH DEFLECTION FITTINGS AT A MAXIMUM SPACING OF 120'.
1'-0" THE DEFLECTION FITTINGS SHALL BE PLACED AT THE TRAFFIC BARRIER OPEN
CONCRETE

1" TIES @ 2½" 1" JOINT THAT COINCIDES WITH THE RETAINING WALL EXPANSION JOINT.
¾" POLYSTYRENE FOAM. WRAP
1 1½ TIMES AROUND CONDUIT
4 LABEL JUNCTION BOX COVER IN ACCORDANCE WITH STANDARD SPECIFICATION SECTION 9-29.2(4).
AND CONDUIT FITTING
ADJACENT JUNCTION BOXES ARE SHOWN CENTERED BETWEEN ADJACENT DUMMY JOINTS. IF THE
DISTANCE BETWEEN ADJACENT DUMMY JOINTS IS 16'-0" OR GREATER, PLACE ADJACENT
¾"

JUNCTION BOXES SYMMETRICALLY ON EITHER SIDE OF THE CENTER OF ONE DUMMY PANEL WHILE
3" MIN., 6" MAX. (CONDUIT AND
MAINTAINING 8'-0" MINIMUM BETWEEN CENTER LINES OF THE JUNCTION BOXES.
SOIL

THREADS CAST OUTSIDE STRUCTURE)

END TERMINATE STEEL CONDUIT IN JUNCTION BOX IF LESS THAN 10-'0" FROM ELBOW OR SWEEP.
CONDUIT DEFLECTION FITTING CONDUIT PIPE 5
B START
WITH INTERNAL BONDING JUMPER
CONDUIT DEFLECTOR FITTING 6 INSTALL ONLY WHERE CONDUIT IS HORIZONTAL.
SHEET

CONDUIT PIPE WITH INTERNAL BONDING JUMPER

7 NEMA 4X IN STATIONARY FORM BARRIER, OR NEMA 3R IN SLIP FORM BARRIER. MOUNT JUNCTION
CONDUIT DEFLECTION FITTING A CONDUIT DEFLECTION FITTING B SECTION B BOX SO COVER IS FLUSH WITH BARRIER, CAN BE RECESSED UP TO Â".

CONDUIT FITTING - TYPE DX FOR DEFLECTION OF 30° AND ¾" MOVEMENT. CONDUIT FITTING - TYPE DX FOR DEFLECTION OF 30° AND ¾" MOVEMENT. 8 3'-0" LONG EXPANDED POLYSTYRENE SLEEVE AROUND CONDUIT. DUCT TAPE SEAMS AND ENDS TO
2 3 SEAL AND PREVENT CONCRETE FROM BONDING WITH FITTING AND CONDUIT.
JOB NO.

Bridge Design Engr.

10.2-A6-3

M:\STANDARDS\Traffic Barriers\Single Slope\SS42TB3.MAN

Supervisor STATE FED. AID PROJ. NO.
Designed By
10 WASH.
Checked By
Detailed By JOB NUMBER
Bridge Projects Engr.
SR

Prelim. Plan By
Architect/Specialist DATE REVISION BY APP'D
Wed Oct 14 12:57:17 2020