18-534

CENTRAL INSTITUTE OF PLASTICS ENGINEERING & TECHNOLOGY

HEAD OFFICE : GUINDY, CHENNAI – 600 032.
ACADEMIC CELL
THIRD SEMESTER EXAMINATION – DECEMBER 2019

Duration : 3 Hours Max. Marks: 60

Course : DPMT Date : 26.12.2019
Subject : Engineering Drawing Time : 10.00 a.m. to 01.00 p.m.
______________________________________________________________________________________

(DO NOT CHANGE SEQUENCE OF QUESTION NUMBER IN ANSWER SCRIPT)

PART – A
Answer all questions 30 x 1 = 30
1. The standard size of drawing sheet for the A3 shall be ___.
(a) 148 x 210 mm (b) 210 x 297 mm (c) 297 x 420 mm (d) 420 x 594 mm.
2. Uses of the T-Square, set-squares, scales and the protractor are combined in the __ machine.
(a) Set-square (b) drafting machine (c) geometric compass (d) all the above.
3. In drawing sheets, perfectly rectangular working space is determined by drawing the __ lines.
(a) hidden lines (b) axis lines (c) dashed thin line (d) border lines.
4. The size of the title block for all sizes of drawing sheets is ____.
(a) 18 x 19 mm (b) 19 x 20 mm (c) 20 x 21 mm (d) 21 x 22 mm
5. ___ line is drawn to connect a note with the feature to which it applies.
(a) Outline (b) Margin lines (c) Dimension lines (d) Leader lines
6. The systems of placing dimensions are ____.
(a) Aligned system (b) Unidirectional system (c) both a & b (d) multidirectional system
7. The ratio of the length of the drawing of the object to the actual length of the object is called _
(a) Resulting fraction (b) representative figure (c) representative fraction (d) none.
8. Drawings of buildings are drawn using ____.
(a) Full-size scale (b) reducing scale (c) scale of chords (d) all the above.
9. When measurements are required in three units ___ scale is used.
(a) Diagonal (b) plain (c) comparative (d) longitudinal
10. The scale of chords is used to set out or measure ___.
(a) Chords (b) lines (c) angles (d) area
11. When a cone is cut by planes at different angles, the curves of intersection are called ___.
(a) Ellipse (b) Circle (c) rectangle (d) conics
12. The curve traced out by a point on a straight line which rolls, without slipping, along a circle or
polygon is ___.
(a) Hyperbola (b) directrix (c) Involute (d) Hypocycloid
13. In a rectangular hyperbola, the product of the distances of any point on it from two fixed lines at right
angles to each other is always constant and lines are called ___.
(a) Focus (b) asymptotes (c) involute (d) none.
14. The line joining any point on the spiral with the pole is called __.
(a)Line vector (b) angle vector (c) radius vector (d) vector.
15. In a conic, the line passing through the fixed point and perpendicular to the fixed line is called
(a)Generator (b) axis (c) directrix (d) asymptotes
16. Write the Full form of BIS
17. Write the Full form of ISO
18. Write the Full form of ASTM
19. What does IEEE stand for___?
20. What does BSW stand for___?
21. The continuous thick lines are being used in visible outlines, visible edges and crests of screw
threads – Say True/False
22. Dashed thick line is applied in line showing permissible of surface treatment – Say True/False
23. The Initial work and construction lines can be drawn by using H pencil – Say True/False
24. Writing of titles, notes etc on a drawing is called lettering – Say True/False
25. When a line is parallel to plane its projection on that plane will show its true length – Say True/False
26. Planes may be divided into ___ and ___.
27. The development of the surface of a Cube consists of ___ equal squares.
28. ___ is a polyhedron having a plane figure as a base and a number of triangular faces meeting at a
point called the ___.
29. ___ is a solid generated by the revolution of a semi-circle about its diameter as the axis.
30. Auxiliary vertical plane is ___ to H.P and ___ to V.P
 18-534
PART – B
Answer all questions (Max. 40 words) 4x2=8

1. What is the difference between first angle and third angle projection?
2. Write in freehand vertical lettering “TIME IS GREAT HEALER” sentence taking size 10mm.
3. Write about the different types of Lines with the applications
4. Define Frustum.

PART – C
Answer any four questions (Max. 100 words) 4 x 3 = 12

1. A point A is 25 mm above the H.P. and 30 mm in front of the V.P. Draw its projections?
2. The top view of a 75mm long line AB measures 65mm, while the length of its front view is 50 mm.
Its
one end A is in the H.P and 12 mm in front of the VP. Draw the projections of AB and determine its
inclinations with the HP and VP
3. A line PQ, 90 mm long, is in the H.P. and makes an angle of 30° with the V.P. Its end P is 25 mm in
front of the V.P. Draw its projections?
4. Write the applications of small bow compass.
5. Construct a regular heptagon given the length of its sides as 50mm.

PART – D
Answer any two questions (Max. 300 words) 2 x 5 = 10

1. Write the methods of development of surfaces.

2. Construct an ellipse when the distance of the focus from the directrix is equal to 50mm and
eccentricity is 2/3.
3. Draw the front view, side view in 1st angle projection of fig. given below with dimensions.

*****************************