0% found this document useful (0 votes)
62 views1 page

Pages From RCJ Specifications

This document specifies fiberglass doors and installation requirements. It outlines accessories for the doors including stops for glazing and louvers made of matching fiberglass. Glazing options include tempered glass, polycarbonate, and laminated safety glass. Louvers for non-fire rated doors must match the door material and color. Door hardware is specified in another section. Installation instructions require examining openings, preparing substrates, installing in accordance with manufacturer instructions, and setting doors plumb and level without warping.

Uploaded by

arch ragab
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
62 views1 page

Pages From RCJ Specifications

This document specifies fiberglass doors and installation requirements. It outlines accessories for the doors including stops for glazing and louvers made of matching fiberglass. Glazing options include tempered glass, polycarbonate, and laminated safety glass. Louvers for non-fire rated doors must match the door material and color. Door hardware is specified in another section. Installation instructions require examining openings, preparing substrates, installing in accordance with manufacturer instructions, and setting doors plumb and level without warping.

Uploaded by

arch ragab
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

08 16 13

FIBERGLASS DOORS

2.05 ACCESSORIES
A. Stops for Glazing and Louver: Fiberglass, unless otherwise indicated or required by fire
rating; provided by door manufacturer to fit factory made openings, with color and texture to
match door; fasteners shall maintain waterproof integrity.
1. Exterior Doors: Provide non-removable stops on exterior side with continuous
compression gasket weatherseal.
2. Glazed Openings: Provide removable stops on interior side.
3. Fire-Rated Doors: Provide stop kit listed by labeling authority.
4. Opening Sizes and Shapes: As indicated on drawings.
B. Glazing:
1. Fully tempered float glass, 6 mm thick, clear.
2. Polycarbonate glazing sheet, 6 mm thick, clear.
3. Laminated safety glass, 6 mm thick, with minimum 0.76 mm thick interlayer, clear.
4. Refer to Specification Section 08 81 00 - Glass Glazing for additional requirements.
C. Louvers for Non-Fire-Rated Doors: Same materials, construction, finish, and color as door;
fixed vanes, 45 degree sloped vanes.
1. Insect Screens: Fiberglass mesh.
D. Louvers for Fire-Rated Doors: not allowed.
E. Door Hardware: As specified in Section 08 71 00.
PART 3 EXECUTION
3.01 EXAMINATION
A. Verify actual dimensions of openings by field measurements before door fabrication; show
recorded measurements on shop drawings.
B. Do not begin installation until substrates have been properly prepared.
C. If substrate preparation is the responsibility of another installer, notify the Royal Commission
of unsatisfactory preparation before proceeding.
3.02 PREPARATION
A. Remove existing doors and frames, and dispose of all removed materials in accordance with
local authorities having jurisdiction.
B. Prepare surfaces using the methods recommended by the manufacturer for achieving the
best result for the substrate under the project conditions.
C. Clean and prepare substrate in accordance with manufacturer's directions.
D. Protect adjacent work and finish surfaces from damage during installation.
3.03 INSTALLATION
A. Install in accordance with manufacturer's instructions; do not penetrate frames with anchors.
B. Install fire-rated assemblies in accordance with NFPA 80.
C. Install exterior doors in accordance with ASTM E2112.
D. Install door hardware as specified in Section 08 71 00.
E. Set units plumb, level, and true-to-line, without warping or racking doors, and with specified
clearances; anchor in place.

Rev 1 7 of 8 Contract No.: XXX-XXX

You might also like