Contents:

1.1 Definition
1.2 History (Generation/Evolution) of Maintenance
1.3 Maintenance Objectives
1.4 Types of Maintenance
1.5 Challenges of Maintenance
1.6 Maintenance Management
1.7 Equipment Life-Cycle
1.8 Function of Maintenance Work
1.1 Definition
The word maintenance is derived from the word
maintain

Maintain is defined as
 cause to continue (Oxford Dictionary), or
 keep in an existing state (Webster Dictionary).
 Cont.
 British Standard Glossary of terms (3811:1993) defined maintenance
as:

the combination of all technical and administrative actions, including

supervision actions, intended to retain an item in, or restore it to, a state
in which it can perform a required function.

maintenance is a set of organised activities that are carried out in order

to keep an item in its best operational condition with minimum cost
acquired.
1.2 Maintenance History
 According to John Moubray (Reliability-Centered
Maintenance), the evolution of maintenance since the
1930's can be traced through three generations based
on three technical factors:

I. growing expectations of maintenance,

II. changing views on equipment failures, and
III. changing maintenance techniques.
 Cont.
First Generation
This covers the period up to the WWII.
During this period:
 industry was not highly mechanized,

 equipment was simple and over designed,

 downtime did not matter much,

 prevention of equipment failure did not have high priority,

 failures were corrected as they occur.

 As a result, there was no need for systematic maintenance

beyond cleaning, servicing and lubrication.
 Cont.
Second Generation
During the war, demand for good increased and supply of industrial outputs was low. This led to
increase in mechanization.

During this period:

 machines became numerous and more complex,

 industry started to depend heavily on these machines,

 downtime started to matter,

 the idea that equipment failures could and should be maintained came up.

 As a result, the concept of preventive maintenance and maintenance planning and control
systems grew up.
 Cont.
Third Generation
Since the mid-seventies, new expectations, new research and new techniques have
revolutionized maintenance.
During this period:
 maximizing life of equipment has become important,

 higher plant availability and reliability have become very important,

 greater automation has been effected,

 quality standards, safety and environmental consequences matter quite a lot,

 cost of maintenance is becoming central,

 As a result: greater expectations are leading to new research which in turn lead to
new techniques.
 GROWING EXPECTATIONS OF
MAINTENANCE

Third Generation:
 Higher plant availability
 Longer equipment life
Second Generation:  Greater cost effectiveness
First Generation:  Higher plant availability  Greater safety
 Fix it when it  Longer equipment life  Better product quality
broke  Lower costs  No damage to the environment

1940 1950 1960 1970 1980 1990 2000

Figure 1.1 Expectations of Maintenance

CHANGING VIEWS ON EQUIPMENT
FAILURE

Figure 1.2 Failure Patterns

 CHANGING MAINTENANCE
TECHNIQUES
Third Generation:
 Condition monitoring
 Design for reliability and
maintainability
 Hazard studies
Second Generation:  Small, fast computers
 Scheduled overhauls  Failure modes and effects
First Generation:  Systems for planning and analyses
 Fix it when it controlling work  Expert systems
broke  Big, slow computers  Multiskilling and teamwork

1940 1950 1960 1970 1980 1990 2000

Figure 1.3 Maintenance Techniques

 Cont.
 Throughout the history of maintenance, it has always had
the same definition.
 It is the management, control, and execution which will
ensure that design levels of availability and performance
of assets are achieved in order to meet the business
objectives.
 The issue that is driving the evolution of maintenance is
that the business objectives are variable over time. They
have continually changed and will continue well into the
future.
 Only by understanding the underlying issues driving this
change will we be better suited to speculate on the future
of the maintenance industry.
 1.3 Objectives of Maintenance
 The main objective of maintenance is the minimization of

the sum of plant unavailability and resource costs

through the proper planning and control of maintenance
work.
Cont.
Specific maintenance objectives for an industry can be the followings:

 To maintain plants and equipment's at its maximum operating

efficiency;
 Ensuring operational safety;

 To safeguard investments by minimizing rate of deterioration

(prolonging life of the equipment) and achieving this at optimum
cost through budgeting and controls;
 assuring instant operational readiness (optimal availability for
production at all times)
Cont.
 Help management in taking decisions on replacements
or new investments and actively participate in
specification preparation, equipment selection, its
erection and commissioning etc,
 Help in implementation of suitable procedures for
procurement, storage and consumption of spares, tools
and consumables etc (inventory control etc)
Cont.
 Standardization of spares and consumables, in conformity

with plant, national and international standards and help in

adoption of these standards by all users in the plant

 Running of centralized services like steam generation and

distribution, water supply, air supply and fuel etc.

 Running of captive workshops for repairs and conditioning

and also for making some new spares; etc.

1.4 Types of Maintenance
 Run to Failure Maintenance (RTF)

 Preventive Maintenance (PM)

 Corrective Maintenance (CM)

 Improvement Maintenance (IM)

 Predictive Maintenance (PDM)

Run to Failure Maintenance (RTF)

 The required repair, replacement, or restore action

performed on a machine or a facility after the
occurrence of a failure in order to bring this
machine or facility to at least its minimum
acceptable condition.

 It is the oldest type of maintenance.

Cont.
 It is subdivided into two types:
 Emergency maintenance: it is carried out as fast as
possible in order to bring a failed machine or facility to a
safe and operationally efficient condition.
 Breakdown maintenance: it is performed after the
occurrence of an advanced considered failure for which
advanced provision has been made in the form of repair
method, spares, materials, labour and equipment.
Cont.
 Disadvantages:

1. Its activities are expensive in terms of both direct and

indirect cost.

2. Using this type of maintenance, the occurrence of a failure

in a component can cause failures in other components in
the same equipment, which leads to low production
availability.

3. Its activities are very difficult to plan and schedule in

advance.
Cont.
 This type of maintenance is useful in the following
situations:

1. The failure of a component in a system is unpredictable.

2. The cost of performing run to failure maintenance activities

is lower than performing other activities of other types of
maintenance.

3. The equipment failure priority is too low in order to include

the activities of preventing it within the planned
maintenance budget.
Preventive Maintenance (PM)
It is a set of activities that are performed on plant equipment,
machinery, and systems before the occurrence of a failure in
order to protect them and to prevent or eliminate any
degradation in their operating conditions.

Its activities include replacements, adjustments, minor overhauls,

inspections and lubrications.
Cont.
British Standard 3811:1993 Glossary of terms
defined preventive maintenance as:

the maintenance carried out at predetermined

intervals or according to prescribed criteria and
intended to reduce the probability of failure or the
degradation of the functioning and the effects
limited.
Cont.
 The factors that affect the efficiency of this type of
maintenance:

1. The need for an adequate number of staff in the

maintenance department in order to perform this
type of maintenance.
2. The required staff qualifications and skills, which
can be gained through training.
3. The support and commitment from executive
management to the PM programme.
4. The proper planning and scheduling of PM
programme.
5. The ability to properly apply the PM programme.
Cont.
 It is good for those machines and facilities which
their failure would cause serious production losses.

 Its aim is to maintain machines and facilities in

such a condition that breakdowns and emergency
repairs are minimised.
Cont.
 Researchers subdivided preventive maintenance into different
kinds according to the nature of its activities:

 Routine maintenance which includes those maintenance activities

that are repetitive and periodic in nature such as lubrication,
cleaning, and small adjustment.

 Running maintenance which includes those maintenance activities

that are carried out while the machine or equipment is running
and they represent those activities that are performed before the
actual preventive maintenance activities take place.

 Shutdown preventive maintenance, which is a set of preventive

maintenance activities that are carried out when the production
line is in total stoppage situation.
Cont.
 Opportunity maintenance which is a set of maintenance
activities that are performed on a machine or a facility when
an unplanned opportunity exists during the period of
performing planned maintenance activities to other machines
or facilities.

 Window maintenance which is a set of activities that are

carried out when a machine or equipment is not required for
a definite period of time.
Corrective Maintenance (CM)
 In this type, actions such as repair, replacement, or
restore will be carried out after the occurrence of a
failure in order to eliminate the source of this
failure or reduce the frequency of its occurrence.

In the British Standard 3811:1993 Glossary of terms,

corrective maintenance is defined as:

the maintenance carried out after recognition and intended to

put an item into a state in which it can perform a required
function.
Cont.
 This type of maintenance is subdivided into three
types:

 Remedial maintenance, which is a set of activities

that are performed to eliminate the source of failure
without interrupting the continuity of the
production process.

The way to carry out this type of corrective maintenance is

by taking the item to be corrected out of the production line
and replacing it with reconditioned item or transferring its
workload to its redundancy.
Cont.
 Deferred maintenance, which is a set of corrective
maintenance activities that are not immediately
initiated after the occurrence of a failure but are
delayed in such a way that will not affect the
production process.

 Shutdown corrective maintenance, which is a set of

corrective maintenance activities that are performed
when the production line is in total stoppage
situation.
Cont.
 The main objectives of corrective maintenance are the
maximisation of the effectiveness of all critical plant
systems, the elimination of breakdowns, the elimination of
unnecessary repair, and the reduction of the deviations from
optimum operating conditions.

 The difference between corrective maintenance and

preventive maintenance is that for the corrective
maintenance, the failure should occur before any corrective
action is taken.

 Corrective maintenance is different from run to failure

maintenance in that its activities are planned and regularly
taken out to keep plant’s machines and equipment in
optimum operating condition.
Cont.
 The way to perform corrective maintenance activities is by
conducting four important steps:

1. Fault detection.
2. Fault isolation.
3. Fault elimination.
4. Verification of fault elimination.

In the fault elimination step several actions could be taken

such as adjusting, aligning, calibrating, reworking,
removing, replacing or renovation.
Cont.
 Corrective maintenance has several prerequisites in
order to be carried out effectively:

1. Accurate identification of incipient problems.

2. Effective planning which depends on the skills of the
planners, the availability of well developed maintenance
database about standard time to repair, a complete repair
procedures, and the required labour skills, specific tools,
parts and equipment.
3. Proper repair procedures.
4. Adequate time to repair.
5. Verification of repair.
Improvement Maintenance (IM)
 It aims at reducing or eliminating entirely the need for
maintenance.
 This type of maintenance is subdivided into three types as
follows:

1. Design-out maintenance which is a set of activities that

are used to eliminate the cause of maintenance, simplify
maintenance tasks, or raise machine performance from the
maintenance point of view by redesigning those machines
and facilities which are vulnerable to frequent occurrence of
failure and their long term repair or replacement cost is very
expensive.
Cont.
2. Engineering services which includes construction and
construction modification, removal and installation, and
rearrangement of facilities.

3. Shutdown improvement maintenance, which is a set of

improvement maintenance activities that are performed
while the production line is in a complete stoppage situation.
Predictive Maintenance (PDM)
 Predictive maintenance is a set of activities that detect
changes in the physical condition of equipment (signs of
failure) in order to carry out the appropriate maintenance
work for maximising the service life of equipment without
increasing the risk of failure.

 It is classified into two kinds according to the methods of

detecting the signs of failure:
 Condition-based predictive maintenance
 Statistical-based predictive maintenance
Cont.
 Condition-based predictive maintenance depends on
continuous or periodic condition monitoring equipment to
detect the signs of failure.

 Statistical-based predictive maintenance depends on

statistical data from the meticulous recording of the
stoppages of the in-plant items and components in order to
develop models for predicting failures.
Cont.
 The drawback of predictive maintenance is that it depends
heavily on information and the correct interpretation of the
information.

 Some researchers classified predictive maintenance as a type

of preventive maintenance.

 The main difference between preventive maintenance and

predictive maintenance is that predictive maintenance uses
monitoring the condition of machines or equipment to
determine the actual mean time to failure whereas preventive
maintenance depends on industrial average life statistics.
Types of Maintenance
MAINTENANCE

PLANNED UNPLANNED
MAINTENANCE MAINTENANCE
(PROACTIVE) (REACTIVE)

EMERGENCY BREAKDOWN

PREDECTIVE PREVENTIVE IMPROVEMENT CORRECTIVE

MAINTENANCE MAINTENANCE MAINTENANCE MAINTENANCE

STATISTICAL CONDITION - DEFERRED REMEDIAL

ENGINEERING DESIGN -
- BASED BASED
SERVICES OUT

Shutdown Maintenance

WINDOW RUNNIN ROUTINE OPPORTU SHUTDOWN SHUTDOWN SHUTDOWN

G -NITY PREVENTIVE IMPROVEMENT CORRECTIVE

Figure 1.5 Maintenance Types

1.5 The Challenges of Maintenance
 The challenges that modern maintenance managers face are
summarized as follows:
 to select the most appropriate maintenance techniques,

 to deal with each type of failure process appropriately,

 in order to fulfill the expectations of users, owners and

society
 in the most cost-effective and sustainable mode, with active
support of people involved.
 1.6 Maintenance Management
Maintenance management is the direction and organization
of resources in order to control the availability and
performance of an industrial plant to a specified level.
 Maintenance is related to profitability through:
 equipment output and equipment running cost.

 time taken for maintenance purposes.

 The importance of maintenance increases with

industrialization.
Cont.
 In maintenance management the problem is two-
dimensional:
 Determination of size and nature of the maintenance

work load,
 Organization and control of labor, spares and equipment

to meet the workload.

1.7 Equipment Life – Cycle
 The level of maintenance required at the equipment

operation stage is affected by factors at other stages

through which the equipment passes.
 Cont.
OPERATIONAL INVOLVEMENT

MANUFACTURE COMMISSIONING OPERATION

SPECIFICATION DESIGN REPLACEMENT
INSTALLATION
- Conceptualization - Performance - Primary design - Design fault - Wear-out
- Reliabilty - Quality control fault control detection - Obsolescence
- Maintainability - Design fault - Technical - Maintenance
- Support system detection performance test optimization
- Maintainability - Maloperation
avoidance

LEARNING PERIOD

CONTINUAL FEEDBACK

Figure 1.6 Equipment Life – Cycle

Fig. 1.2 Equipment life-cycle
Cont.
 Design stage:
 Reliability and maintainability are the important factors which should be considered
properly in relation to performance of equipment, capital and running costs.
 Installation stage:
 Maintainability is an important factor to be considered during the installation, for it is
here that maintenance problems become clear.
 Commissioning stage:
 This is a stage of technical performance testing and also a stage of where primary
design faults are located and designed out.
 Operational stage:
 The operational stage is a stage of learning where maintenance plays an important
role.
1.8 Function of Maintenance Work

 Today it is being considered as "Maintenance affects all

aspects of business effectiveness and risk-safety,

environmental integrity, energy efficiency, product
quality and customer service, not just plant availability
and cost."
Cont.
 The maintenance department influences plant availability directly through
preventive and corrective maintenance.

The most basic definition of availability is Tup

Availability 
Tup  Tdown
where Tup = cumulative time of operation
Tdown = cumulative outage time
Tdown = Down time = repair time + delays

Repair time = f(maintainability, management method, engineering techniques)

Delays = f(organization of maintenance resources and information)

Figure 1.7 Equipment Time
Figure 1.8 Equipment Down Time