Scribd
Upload
323 views3 pages

Código Nome

This document contains codes and descriptions related to faults in the steering system of an agricultural vehicle. It lists codes for issues with unswitched supply voltage levels, missing differential correction and GPS speed messages, steering valve calibration faults, sensor voltage and current levels, steering valve coil currents, the master switch state, missing messages from other controllers, and faults with the wheel angle and steering wheel pressure sensors.

Uploaded by

rafael
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
323 views3 pages

Código Nome

This document contains codes and descriptions related to faults in the steering system of an agricultural vehicle. It lists codes for issues with unswitched supply voltage levels, missing differential correction and GPS speed messages, steering valve calibration faults, sensor voltage and current levels, steering valve coil currents, the master switch state, missing messages from other controllers, and faults with the wheel angle and steering wheel pressure sensors.

Uploaded by

rafael
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLSX, PDF, TXT or read online on Scribd
You are on page 1/ 3

Código Nome

SSU 000168.03 Unswitched supply voltage high


Indicates SSU unswitched supply voltage (cc# 182) out of range high.
SSU 000168.04 Unswitched supply voltage low
Indicates SSU unswitched supply voltage (cc# 182) out of range low.
SSU 000232.09 StarFire Differential Status message missing
Indicates differential correction signal to GPS is not available.
SSU 000517.09 GPS speed message missing
Indicates GPS Speed Message Missing.
SSU 000628.12 SSU programming
Indicates control unit SSU being reprogrammed (boot block generated). Reprogram control unit SSU. Replace control unit SSU if condition
persists.
SSU 000630.13 SSU calibration fault/not calibrated
Indicates incomplete calibration of steering valve. Wheel Angle Sensor calibration incomplete. AutoTrac will remain disabled until successful
calibration of system.
SSU 003509.03 Sensor voltage too high
Indicates sensor supply voltage (cc# 733) for steering wheel pressure sensor and/or wheel angle position sensor out of range high.
SSU 003509.04 Sensor voltage too low.
Indicates sensor supply voltage (cc# 733) for steering wheel pressure sensor and/or wheel angle position sensor out of range low.
SSU 003509.05 Sensor supply current below normal or open circuit
Indicates sensor supply current below normal on (cc# 733) for steering wheel pressure sensor and/or wheel angle position sensor.
SSU 003509.06 Sensor supply current above normal or grounded circuit
Indicates sensor supply current above normal on (cc# 733) for steering wheel pressure sensor and/or wheel angle position sensor.
SSU 004086.03 Steering Wheel Pressure Sensor voltage above normal

Indicates steering wheel pressure sensor (cc# 777), load sense pressure output faulty. Voltage too high. AutoTrac will keep disengaging.
SSU 004086.04 Steering Wheel Pressure Sensor voltage below normal

Indicates steering wheel pressure sensor (cc# 777), load sense pressure output faulty. Voltage too low. AutoTrac will keep disengaging.
SSU 520429.05 Steering valve left coil current too low
Indicates steering valve left coil (cc# 742) current too low or open circuit.
SSU 520429.06 Steering valve left coil current too high
Indicates steering valve left coil (cc# 742) current too high or shorted to ground.
SSU 520429.31 Steering valve left coil shorted to ground
Indicates steering valve left coil (cc# 742) shorted to ground.
SSU 520430.05 Steering valve right coil current too low
Indicates steering valve left coil (cc# 752) current too low or open circuit.
SSU 520430.06 Steering valve right coil current too high
Indicates steering valve left coil (cc# 752) current too high or shorted to ground.
SSU 520430.31 Steering valve right coil shorted to ground
Indicates steering valve left coil (cc# 752) shorted to ground.
SSU 520431.05 Steering isolation valve coil current too low.
Indicates steering isolation valve (cc# 792) current too low or open circuit.
SSU 520431.06 Steering isolation valve coil current too high.
Indicates steering isolation valve (cc# 792) current too high or shorted to ground.
SSU 522385.01 AutoTrac master swtich is not ON.
Indicates that the AutoTrac Controller ON/OFF switch on vehicle is not ON.
SSU 522387.07 Wheel Angle Sensor or Steering Valve Fault
Indicates control unit SSU not receiving wheel angle position sensor signal.
SSU 522394.09 TCM messages missing
Indicates control unit SSU not receiving terrain compensation module CAN Bus message.
SSU 523651.02 Control unit malfunction
Indicates control unit SSU malfunction: stack overflow. Clear code. Replace control unit SSU if condition persists.
SSU 523698.09 SSU not receiving parallel tracking set A/B line message.
Indicates control unit SSU not receiving parallel tracking set A/B line message.
SSU 523767.02 AutoTrac resume switch circuits conflict
Indicates control unit SSU not receiving Resume Switch (cc# 909) output signal.
SSU 523795.02 Steering valve orientation incorrect
Indicates steering valve orientation incorrect. Check steering valve right/left circuit codes switched.
SSU 523795.11 Steering valve deadbands inconsistent
Indicates steering valve deadbands inconsistent.
SSU 523795.13 Incomplete valve calibration.
Indicates steering valve calibration fault. Recalibrate Steering system. Replace steering valve if condition persists.
SSU 523808.00 Steering control right/left valve supply voltage to high
Indicates steering control valve (cc# 752/742 supply voltage to right/left coil too high.
SSU 523808.01 Steering control right/left valve supply voltage too low
Indicates steering control valve (cc# 752/742 supply voltage to right/left coil too low.
SSU 523809.01 Steering isolation valve supply voltate too low
Indicates steering isolation valve supply (cc# 792) voltage too low.
SSU 523822.05 Wheel angle position sensor current too low
Indicates wheel angle position sensor current too low or open circuit.
SSU 523822.06 Wheel angle position sensor current too high
Indicates wheel angle position sensor current too high or short to ground.
SSU 523826.00 Wheel angle sensor primary signal high
Wheel angle position sensor output (cc# 736) data valid but above normal operational range.
SSU 523826.01 Wheel angle sensor primary signal low
Wheel angle position sensor output (cc# 736) data valid but below normal operational range.
SSU 523826.02 Wheel angle sensor orientation incorrect
Wheel angle sensor orientation incorrect. Indicates a backwards sensor reading. Diagnostic Trouble Code thrown only on calibration.
SSU 523826.07 Wheel angle position sensor calibration problem
Wheel angle position sensor range too small. Recalibrate wheel angle position sensor.
SSU 523826.10 SSU fault active
Wheel angle position sensor detects motion but not steering wheel pressure sensor.
SSU 524221.09 SSU not receiving yaw rate message
Steering valve cannot be commanded, no yaw rate message.

You might also like