Scribd
Upload
155 views2 pages

8 Investment Casting Process

The investment casting process, also known as the lost wax process, dates back thousands of years. It involves creating a wax pattern, assembling multiple patterns, investing them in refractory material, heating to melt out the wax, and pouring molten metal. The basic steps are producing wax patterns, assembling them on a gate system, investing in refractory slurry, dewaxing by melting, firing to remove wax residue, and pouring metal. In ceramic shell investment casting, a ceramic shell is built around the wax pattern by repeatedly dipping in refractory slurry. The shell is then fired to burn out the wax and develop bonding before metal is poured.

Uploaded by

Fahri Ramadhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
155 views2 pages

8 Investment Casting Process

The investment casting process, also known as the lost wax process, dates back thousands of years. It involves creating a wax pattern, assembling multiple patterns, investing them in refractory material, heating to melt out the wax, and pouring molten metal. The basic steps are producing wax patterns, assembling them on a gate system, investing in refractory slurry, dewaxing by melting, firing to remove wax residue, and pouring metal. In ceramic shell investment casting, a ceramic shell is built around the wax pattern by repeatedly dipping in refractory slurry. The shell is then fired to burn out the wax and develop bonding before metal is poured.

Uploaded by

Fahri Ramadhan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Investment Casting Process

The root of the investment casting process, the cire perdue or “lost wax” method dates back
to at least the fourth millennium B.C. The artists and sculptors of ancient Egypt and
Mesopotamia used the rudiments of the investment casting process to create intricately
detailed jewelry, pectorals and idols. The investment casting process alos called lost wax
process begins with the production of wax replicas or patterns of the desired shape of the
castings. A pattern is needed for every casting to be produced. The patterns are prepared by
injecting wax or polystyrene in a metal dies. A number of patterns are attached to a central
wax sprue to form a assembly. The mold is prepared by surrounding the pattern with
refractory slurry that can set at room temperature. The mold is then heated so that pattern
melts and flows out, leaving a clean cavity behind. The mould is further hardened by heating
and the molten metal is poured while it is still hot. When the casting is solidified, the mold is
broken and the casting taken out.

The basic steps of the investment casting process are ( Figure 11 ) :

1. Production of heat-disposable wax, plastic, or polystyrene patterns


2. Assembly of these patterns onto a gating system
3. “Investing,” or covering the pattern assembly with refractory slurry
4. Melting the pattern assembly to remove the pattern material
5. Firing the mold to remove the last traces of the pattern material
6. Pouring
7. Knockout, cutoff and finishing.

Figure 11: The Basic Steps of the Investment Casting Process

Advantages

 Formation of hollow interiors in cylinders without cores


 Less material required for gate
 Fine grained structure at the outer surface of the casting free of gas and shrinkage
cavities and porosity

Disadvantages

 More segregation of alloy component during pouring under the forces of rotation
 Contamination of internal surface of castings with non-metallic inclusions
 Inaccurate internal diameter

Ceramic Shell Investment Casting Process

The basic difference in investment casting is that in the investment casting the wax pattern is
immersed in a refractory aggregate before dewaxing whereas, in ceramic shell investment
casting a ceramic shell is built around a tree assembly by repeatedly dipping a pattern into a
slurry (refractory material such as zircon with binder). After each dipping and stuccoing is
completed, the assembly is allowed to thoroughly dry before the next coating is applied.
Thus, a shell is built up around the assembly. The thickness of this shell is dependent on the
size of the castings and temperature of the metal to be poured.
After the ceramic shell is completed, the entire assembly is placed into an autoclave or flash
fire furnace at a high temperature. The shell is heated to about 982 o C to burn out any
residual wax and to develop a high-temperature bond in the shell. The shell molds can then
be stored for future use or molten metal can be poured into them immediately. If the shell
molds are stored, they have to be preheated before molten metal is poured into them.

Advantages

 excellent surface finish


 tight dimensional tolerances
 machining can be reduced or completely eliminated

You might also like