Energy Measurement

Energy measurement
MT83x
Energy measurement
Communication
Specification
Energy Measurement and Management
MT83x Communication specifications IEC62056-21

(former IEC1107) with examples
COMMON REMARKS TO COMMUNICATION PROTOCOL
1. IEC62056-21 (former IEC1107) standard is used (for data formats, timeouts,...) – Mode C with
password
2. OBIS (Energy Data Information System) = Preliminary standard by IEC TC13 WG14 number
62056-61
3. Supported commands are:

 R1 - read single
 R5 - read of P.01 (Load-profile), P.98 (LogBook),
 R6 - partial block read-out of P.01 and P.98
 W1 - write single command – only allowed if specific access level is fulfilled (password)
 W5 - For write of register 0.9.1(time), 0.9.2(date), 0.9.4 (time and date together) with
password for W5 command
 E2 - execute command
 P1 - sending of Password – for opening password access key
4. Supported baudrates:
 For optical interface – up to 9600 baud
 For RS-232, RS-485 and 20-mA current loop – up to 19.200 baud (recommended 9600)
5. RS-232, RS-485 or 20-mA current loop interface can operate without switching of baudrate
from 300 to "Z" baud as stands in IEC 1107. In the case that there is fixed baudrate on RS-
232/485 or 20-mA current loop interface it is necessary to send some NUL characters (typ. 8
characters) or to implement "Retry" (two or three) of opening sequence (/?!CRLF) to "wake up"
the port and to prepare the MT830 for the right communication baudrate. The MT830 is always
waiting the very first character in request on 300 baud.
6. Optical interface always work with switch of baudrate from 300 to “z”.
Comm_des_MT830 1 14.11.12
Data formats
The assignements for the formats in the tables/data representations have the following meaning:
 “Bmn” bitmap, n Octets

 “D6” date (YYMMDD)
 “Ds7” seasonal date (yYYMMDD)
 “Fn(x,y)” floating decimal number
 “In” integer number
 “Sn” alphanumeric string
 “T4” time 1 (hhmm)
 “Ts5” seasonal time 1 (yhhmm)
 “T6” time 2 (hhmmss)
 “Ts7” seasonal time 2 (yhhmmss)
 “TST11” time stamp 1 (MM.DD.hh:mm)
 “TST10” time stamp 2 (YYMMDDhhmm)
 “TSTs11” seasonal time stamp 2 (yYYMMDDhhmm)
 “TST12” time stamp 3 (YYMMDDhhmmss)
 “TSTs13” seasonal time stamp 3 (yYYMMDDhhmmss)
For integer numbers and alphanumeric strings n specifies the total number of characters.
For floating decimals, the number in front of the brackets specifies the total number of digits. The
numbers within the brackets specify the range for the number of decimal positions.
For dates, times and timestamps the number specifies the total number of digits including any
separation characters between. Definition for seasonal parameter “y”:
y = 0: normal time
y = 1: daylight savings time
y = 2: UTC
Comm_des_MT830 2 14.11.12
List of er_ (errata) info
The following table describes returned ER_ as they are sent by meter device in cases of
unsuccessfully executed IEC1107 command. This mechanism is used by IEC1107 protocol to
inform the user why requested command can not be executed.
IEC1107_ERROR_NOTFOUND ER01
IEC1107_ERROR_NOTIMPLEMENTED ER02
IEC1107_ERROR_BADPARAM ER03
IEC1107_ERROR_BADINDEX ER04
IEC1107_ERROR_BADVALUE ER05
IEC1107_ERROR_BADCOMMAND ER06
IEC1107_ERROR_NOTAUTHORISED ER07
IEC1107_ERROR_NODATA ER08
IEC1107_ERROR_NORESOURCE ER09
IEC1107_ERROR_DEVICEERROR ER10
IEC1107_ERROR_BADADDRESS ER11
IEC1107_ERROR_UNKNOWN ER12
Example:
16969 ms elapsed -> IEC1107 opening local connection

15 ms elapsed -> IEC62056-21 sending:
<NUL><NUL><NUL><NUL>
/?!<_CR><_LF>
1172 ms elapsed -> IEC62056-21 received:

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>
219 ms elapsed -> IEC62056-21 changing baudrate to 9600:

<SOH>P0<STX>(8b778a96)<ETX>l
<SOH>R1<STX>0.0.128.3.4()<ETX>_
<STX>ER(11)<ETX><NAK>
<SOH>B0<ETX>q
2406 ms elapsed -> IEC1107 closing local connection
Comm_des_MT830 3 14.11.12
4. LOG-BOOK event recorder
LogBook event recorder has place for 255 events.
LB code Data name

LB.0080 Power down
LB.0040 Power up
LB.8102 Voltage down phase L1
LB.8105 Under-voltage phase L1
LB.8108 Voltage normal phase L1
LB.810A Voltage normal phase L3
LB.810B Over-voltage phase L1
LB.810C Over-voltage phase L2
LB.810D Over-voltage phase L3
LB.810E Billing reset
LB.810F RTC sync start
LB.8110 RTC sync end
LB.0020 RTC Set
LB.0008 DST
LB.2000 Log-Book erased
LB.4000 Load-Profile erased
LB.0001 Device disturbance
LB.8117 Parameters changed
LB.8118 Watch dog
LB.8119 Fraud start
LB.811A Fraud end
LB.811B Terminal cover opened
LB.811C Terminal cover closed
LB.811D Main cover opened
LB.811E Main cover closed
LB.811F Master reset
LB.8120 Parameter changed via remote comm.
LB.8121 Scheduled parameter change
LB.8122 Private key changed
LB.8123 Local communication started
LB.8124 Local communication ended
LB.8125 Remote communication started
LB.8126 Remote communication ended
LB.8127 GPS communication established
LB.8128 GPS communication lost
LB.8129 Contract1 communication started
LB.812A Contract1 parameter changed
LB.812B Contract1 parameter changed
LB.812C Contract1 parameter changed
LB.812D Contract1 parameter changed
Comm_des_MT830 4 14.11.12
LB.812E Contract1 billing reset

LB.812F Contract2 communication started
LB.8130 Contract2 parameter changed
LB.8134 Contract2 billing reset
LB.813A Contract3 billing reset
LB.813B Contract4 communication started
LB.813E Contract4 parameter changed
LB.813F Contract4 parameter changed
LB.8141 Reverse power flow
LB.8142 Breaker failure
LB.8143 Invalid password
LB.8144 Corrupted SMS
LB.8145 Incorrect credit code
LB.8146 Keypad locked
LB.8147 GSM network failure
LB.8148 Programming failed
LB.8149 Invalid SMS source
LB.814A All code entered
LB.814B Valid code time
LB.814C Customer purchase request
LB.814D Meter removal
LB.814E Full Technical Log Book
LB.814F Unable to send SMS alarm
LB.8150 Intrusion reset
LB.8151 Previous values reset
Current without Voltage phase L1 - start
LB.8152
LB.8153 Current without Voltage phase L2 – start
LB.8154
Current without Voltage phase L1 - end
LB.8155
LB.8156 Current without Voltage phase L2 – end
LB.8157
Logbook read is possible with commands R5 (all in one block) or R6 (in partial blocks).
Format:
 <SOH>R5<STX>P.98(;) - Read all 255 events in one block
Comm_des_MT830 5 14.11.12
 <SOH>R5<STX>P.98(TSTs11; TSTs11) - Read “from – to” in one block

 <SOH>R6<STX>P.98(;;N) - Read N LogBook events per block
 <SOH>R5<STX>P.98(TSTs11; TSTs11;N) - Read “from – to” N LB events per block
LogBook Format :
P.98(TSTs13)(Sn) - the oldest LogBook event

(TSTs13)(Sn)
....
(TSTs13)(Sn) - the youngest LogBook event (255.)
Example:
1. R5 command – total

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(58a7dbba)<ETX>>
<SOH>R5<STX>P.98(;)<ETX>#
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
(0060115213109)(0040)<_CR><_LF>
(0060115213110)(811b)<_CR><_LF>
(0060115213112)(8105)<_CR><_LF>
(0060115213112)(8106)<_CR><_LF>
(0060115213112)(8107)<_CR><_LF>
(0060115213118)(0010)<_CR><_LF>
(0060115213625)(8102)<_CR><_LF>
(0060115213627)(8105)<_CR><_LF>
(0060115213630)(8102)<_CR><_LF>
(0060115213633)(8105)<_CR><_LF>
(0060115213648)(8102)<_CR><_LF>
(0060115213716)(0020)<_CR><_LF>
(0060115235716)(0020)<_CR><_LF>
<ETX>7
Comm_des_MT830 6 14.11.12
<SOH>B0<ETX>q
2. R5 command - “from – to”

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(c433fd5d)<ETX>d
<SOH>P1<STX>(*****)<ETX>.
<ACK>
<SOH>R5<STX>P.98(00601151700;00601152100)<ETX>&
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<ETX>W
<SOH>B0<ETX>q
3. R6 command  block reading

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>
Comm_des_MT830 7 14.11.12

<SOH>P0<STX>(e9e80164)<ETX>b
<ACK>
<SOH>R6<STX>P.98(;;10)<ETX>\x1a
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<EOT>P
<ACK>
<STX>(0060115213109)(0040)<_CR><_LF>
(0060115213110)(811b)<_CR><_LF>
(0060115213112)(8105)<_CR><_LF>
(0060115213112)(8106)<_CR><_LF>
(0060115213112)(8107)<_CR><_LF>
(0060115213118)(0010)<_CR><_LF>
(0060115213625)(8102)<_CR><_LF>
(0060115213627)(8105)<_CR><_LF>
(0060115213630)(8102)<_CR><_LF>
(0060115213633)(8105)<_CR><_LF>
<EOT>U
<ACK>
<STX>(0060115213648)(8102)<_CR><_LF>
(0060115213716)(0020)<_CR><_LF>
(0060115235716)(0020)<_CR><_LF>
<ETX>2
<SOH>B0<ETX>q
4. R6 command - “from – to” block reading

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>
Comm_des_MT830 8 14.11.12

<ACK>051<_CR><_LF>

<SOH>P0<STX>(d0cfda92)<ETX>?
<ACK>
<SOH>R6<STX>P.98(00601151600;00601152100;5)<ETX>*
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
<EOT>2
<ACK>
<STX>(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<ETX>a
<SOH>B0<ETX>q
5. E2 command
Billing reset (MD reset)
Billing reset can be performed via communication interface by E2 command.
Format:
SOH E 2 STX 0.0.5.0.4.0 ETX BCC
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>
Comm_des_MT830 9 14.11.12

<ACK>051<_CR><_LF>

<SOH>P0<STX>(58a7c30a)<ETX>:
<ACK>
<SOH>E2<STX>0.0.5.0.4.0()<ETX>X
<ACK>
<SOH>B0<ETX>q
6. Load profile
Load profile read is possible with commands R5 (one block) or R6 (partial block).
Format:
 <SOH>R5<STX>P.01(;) LP all – from beginning till the end, all channels
 <SOH>R5<STX>P.01(TSTs11;TSTs11) LP “from – to”, all channels
 <SOH>R6<STX>P.01(;;N) LP in blocks with N records per block, all channels
 <SOH>R6<STX>P.01(TSTs11;TSTs11;N) LP “from-to” in blocks with N records per block
TSTs11 = (sYYMMDDhhmm) - s = season (0 = winter, 1 = summer)
By R6 command the reading device (PC or HHU) has to send <ACK> if block checksum is OK or
<NAK> if it is not OK. In latter case the meter will repeat sending the same block for 3 times (if
each time checksum is not OK).
Example:
1. Reading all LP with R5 command
23/08/2005 14:41:18, Log Started

0 ms elapsed -> IEC1107 sending:
/?!<_CR><_LF>
Comm_des_MT830 10 14.11.12
1022 ms elapsed -> IEC1107 received:

/ISK5MT830-1007<_CR><_LF>

<ACK>051<_CR><_LF>
210 ms elapsed -> IEC1107 changing baudrate to 9600:

<SOH>P0<STX>(8b776701)<ETX>:
<ACK>
<SOH>R5<STX>P.01(00508221400;00508222100)<ETX>%
<STX>P.01(0050822143000)(00)(30)(11)<_CR><_LF>
(1.8)( kWh)(3.8)( kvarh)(32.5)( V)(52.5)( V)(72.5)( V)(31.5)( A)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00047.713)(00001.367)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.6)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00047.935)(00001.373)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.5)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00048.161)(00001.380)(229.5)(229.6)(0.0)(19.6)<_CR><_LF>
(19.7)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
P.01(0050822160000)(10)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00048.423)(00001.387)(228.9)(229.0)(36.0)(18.8)<_CR><_LF>
(18.9)(2.0)(0.9995)(0.9993)(0.9999)<_CR><_LF>
P.01(0050822163000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00049.077)(00001.410)(228.9)(229.0)(228.9)(18.9)<_CR><_LF>
(19.2)(18.9)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00049.733)(00001.434)(228.9)(229.1)(228.9)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00050.397)(00001.457)(230.5)(230.7)(230.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.064)(00001.481)(230.6)(230.8)(230.6)(19.2)<_CR><_LF>
(19.4)(19.2)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.725)(00001.504)(229.5)(229.6)(229.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00052.383)(00001.528)(228.7)(228.8)(228.7)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.046)(00001.551)(229.4)(229.5)(229.4)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.704)(00001.575)(228.6)(228.7)(228.6)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00054.357)(00001.598)(227.6)(227.7)(227.6)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00055.014)(00001.622)(228.4)(228.6)(228.4)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<ETX>b
<SOH>B0<ETX>q
Comm_des_MT830 11 14.11.12
and with R6 command
23/08/2005 14:42:51, Log Started

/?!<_CR><_LF>

/ISK5MT830-1007<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(4e4902b8)<ETX>d
<ACK>
<SOH>R6<STX>P.01(00508221400;00508222100;10)<ETX>\x1c
<STX>P.01(0050822143000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00047.713)(00001.367)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.6)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00047.935)(00001.373)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.5)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00048.161)(00001.380)(229.5)(229.6)(0.0)(19.6)<_CR><_LF>
(19.7)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
P.01(0050822160000)(10)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00048.423)(00001.387)(228.9)(229.0)(36.0)(18.8)<_CR><_LF>
(18.9)(2.0)(0.9995)(0.9993)(0.9999)<_CR><_LF>
P.01(0050822163000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00049.077)(00001.410)(228.9)(229.0)(228.9)(18.9)<_CR><_LF>
(19.2)(18.9)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00049.733)(00001.434)(228.9)(229.1)(228.9)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00050.397)(00001.457)(230.5)(230.7)(230.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.064)(00001.481)(230.6)(230.8)(230.6)(19.2)<_CR><_LF>
(19.4)(19.2)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.725)(00001.504)(229.5)(229.6)(229.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00052.383)(00001.528)(228.7)(228.8)(228.7)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<EOT>h
<ACK>
Comm_des_MT830 12 14.11.12

<STX>P.01(0050822193000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00053.046)(00001.551)(229.4)(229.5)(229.4)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.704)(00001.575)(228.6)(228.7)(228.6)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00054.357)(00001.598)(227.6)(227.7)(227.6)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00055.014)(00001.622)(228.4)(228.6)(228.4)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<ETX>^
<SOH>B0<ETX>q
2. Reading all LP with R5 command (Multiples header formating) – for reading with P2S
Parameter “Map 1107 Mode” (in MeterView: group Common) must be set to Multiples in order to
get following readout.
Examples:
23/08/2007 14:41:18, Log Started

/?!<_CR><_LF>
Comm_des_MT830 13 14.11.12
/ISK5MT830-1034<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(8b776701)<ETX>:
<ACK>
<SOH>R5<STX>P.01(;)<ETX>%
<STX>P.01<_CR><_LF> ……Load profile name
(0709232100)<_CR><_LF> ……Time of record
(c0)<_CR><_LF> ……Status
(30)<_CR><_LF> ……Register period [min]
(4)<_CR><_LF> ……Number of chanells
(1.8)<_CR><_LF> ……Chanell names with units
(kWh)<_CR><_LF> ……Chanell units
(2.8)<_CR><_LF>
(kWh)<_CR><_LF>
(3.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(4.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(00044.671)(00000.000)(00001.959)(00000.000)<_CR><_LF> …..Chanell values
(00045.700)(00000.000)(00002.000)(00000.000)<_CR><_LF>
P.01<_CR><_LF>
(0709232200)<_CR><_LF>
(00)<_CR><_LF>
(30)<_CR><_LF>
(4)<_CR><_LF>
(1.8)<_CR><_LF>
(kWh)<_CR><_LF>
(2.8)<_CR><_LF>
(kWh)<_CR><_LF>
(3.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(4.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(00046.793)(00000.000)(00002.047)(00000.000)<_CR><_LF>
(00047.888)(00000.000)(00002.095)(00000.000)<_CR><_LF>
(00048.992)(00000.000)(00002.143)(00000.000)<_CR><_LF>
(00050.089)(00000.000)(00002.190)(00000.000)<_CR><_LF>
(00051.146)(00000.000)(00002.234)(00000.000)<_CR><_LF>
<ETX><EOT>
<SOH>B0<ETX>q
Comm_des_MT830 14 14.11.12
7. Time and date setting (time synchronization)
There are four possibilities for set time and date in MT83x:
 with command W1 and write of registers 0.9.1 and 0.9.2 - two steps
 with command W1 and register 0.9.4 - one step
1.1. Command W1 and write of registers 0.9.1 and 0.9.2
0.9.1 Time write HHU => meter (=request)

SOH W1 STX 0.9.1 ( T6 ) ETX BCC
meter => HHU (=response)
'ACK' or 'NAK' or 'ERxy'
Remark:
In case of wrong format response will be 'ER05'
0.9.2 Date write HHU => meter (=request)

SOH W1 STX 0.9.2 ( D6 ) ETX BCC
Remark:
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(675effe7)<ETX>c
<SOH>P1<STX>(***)<ETX>#
<ACK>
<SOH>W1<STX>0.9.1(123015)<ETX>Z
Comm_des_MT830 15 14.11.12
<ACK>
<SOH>W1<STX>0.9.2(060225)<ETX>^
<ACK>
<SOH>B0<ETX>q

SOH W5 STX 0.9.1 ( T6 ) ( Password W5) ETX BCC
Remark:

SOH W5 STX 0.9.2 ( D6 ) ( Password W5) ETX BCC
Remark:
Example:
/?!<_CR><_LF>

/ISK4MT860-1007<_CR><_LF>

<ACK>041<_CR><_LF>

<SOH>P0<STX>(ebd86399)<ETX>>
<SOH>W5<STX>0.9.1(123013)(SET)<ETX><ESC>
<ACK>
<SOH>B0<ETX>q
Comm_des_MT830 16 14.11.12
1.3. Command W1 and write of register 0.9.4

SOH W1 STX 0.9.4 ( TST12 ) ETX BCC
Remark:
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(e3ada0ef)<ETX>a
<ACK>
<SOH>W1<STX>0.9.4(060117152508)<ETX>Q
<ACK>
<SOH>B0<ETX>q

SOH W5 STX 0.9.4 ( TST12 ) ( Password W5) ETX BCC
'ACK' or 'NAK' or 'ER(xy)'
Remark:
Comm_des_MT830 17 14.11.12
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(d0cdaef1)<ETX>`
<SOH>W5<STX>0.9.4(060117150939)(SET)<ETX>\x1a
<ACK>
<SOH>B0<ETX>q
8. Time and date reading
1.5. Command R1 and reading of register 0.9.1 , 0.9.2 , 0.9.4
0.9.1 Time read HHU => meter (=request)

SOH R1 STX 0.9.1 () ETX BCC
STX 0.9.1 ( T6 ) ETX BCC
0.9.2 Date read HHU => meter (=request)

STX 0.9.2 ( D6 ) ETX BCC
0.9.4 Date and time HHU => meter (=request)

read SOH R1 STX 0.9.4 () ETX BCC
STX 0.9.4 (TST12) ETX BCC
Example:

Comm_des_MT830 18 14.11.12
/?!<_CR><_LF>

/ISK5MT830-1047<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(b06d0786)<ETX>i
<SOH>R1<STX>0.9.1()<ETX>[
<STX>(204522)<ETX><SOH>
<SOH>R1<STX>0.9.2()<ETX>X
<STX>(070925)<ETX>\x0b
<SOH>R1<STX>0.9.4()<ETX>^
<STX>(070925204531)<ETX><_LF>

<SOH>B0<ETX>q
3328 ms elapsed -> IEC62056-21 closing local connection



Example:

Comm_des_MT830 19 14.11.12
/?!<_CR><_LF>

/ISK5MT830-1047<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(03767f47)<ETX>0
<SOH>R5<STX>0.9.1()<ETX>_
<STX>0.9.1(205448)<ETX>5
<SOH>R5<STX>0.9.2()<ETX>\
<STX>0.9.2(070925)<ETX>0
<SOH>R5<STX>0.9.4()<ETX>Z
<STX>0.9.4(070925205454)<ETX>4
<SOH>B0<ETX>q
9. Data readout
Data readout is performed with a standard command of the Mode C protocol:
ACK, 0, Z, 0, CR, LF
After reception of this command, the MT83x meter transmits values of all data which are stated in
the DRO sequence.
Example:
Data readout of a four-quadrant meter with 2 tariffs and 15 previous values:
16437 ms elapsed -> IEC1107 opening local 218 ms elapsed -> IEC62056-21 changing baudrate
connection to 9600:
16 ms elapsed -> IEC62056-21 sending: 8500 ms elapsed -> IEC62056-21 received:
<NUL><NUL><NUL><NUL> <STX>0.0.0(00000000)<_CR><_LF>
547 ms elapsed -> IEC62056-21 sending: 0.9.1(180612)<_CR><_LF>
/?!<_CR><_LF> 0.9.2(060116)<_CR><_LF>
0.1.0(3)<_CR><_LF>
1172 ms elapsed -> IEC62056-21 received: 0.1.2*01(0601161742)<_CR><_LF>
/ISK5MT830-1013<_CR><_LF> 0.1.2*02(0601160134)<_CR><_LF>
0.1.2*03(0601152131)<_CR><_LF>
203 ms elapsed -> IEC62056-21 sending: 0.1.2*04()<_CR><_LF>
<ACK>050<_CR><_LF> 0.1.2*05()<_CR><_LF>
0.1.2*06()<_CR><_LF>
Comm_des_MT830 20 14.11.12
0.1.2*07()<_CR><_LF> 9.6.0*10()<_CR><_LF>
0.1.2*08()<_CR><_LF> 9.6.0*11()<_CR><_LF>
0.1.2*09()<_CR><_LF> 9.6.0*12()<_CR><_LF>
0.1.2*10()<_CR><_LF> 9.6.0*13()<_CR><_LF>
0.1.2*11()<_CR><_LF> 9.6.0*14()<_CR><_LF>
0.1.2*12()<_CR><_LF> 9.6.0*15()<_CR><_LF>
0.1.2*13()<_CR><_LF> 1.8.0(00001.0 kWh)<_CR><_LF>
0.1.2*14()<_CR><_LF> 1.8.0*01(00000.9 kWh)<_CR><_LF>
0.1.2*15()<_CR><_LF> 1.8.0*02(00000.1 kWh)<_CR><_LF>
1.2.0(000.2008 kW)<_CR><_LF> 1.8.0*03(00000.0 kWh)<_CR><_LF>
1.6.0(0.0774 kW)(0060116180000)<_CR><_LF> 1.8.0*04()<_CR><_LF>
1.6.0*01(0.0516 kW)(0060116083000)<_CR><_LF> 1.8.0*05()<_CR><_LF>
1.6.0*02(0.0500 kW)(0060116013000)<_CR><_LF> 1.8.0*06()<_CR><_LF>
1.6.0*03(0.0992 kW)(0060115213000)<_CR><_LF> 1.8.0*07()<_CR><_LF>
1.6.0*04()<_CR><_LF> 1.8.0*08()<_CR><_LF>
1.6.0*05()<_CR><_LF> 1.8.0*09()<_CR><_LF>
1.6.0*06()<_CR><_LF> 1.8.0*10()<_CR><_LF>
1.6.0*07()<_CR><_LF> 1.8.0*11()<_CR><_LF>
1.6.0*08()<_CR><_LF> 1.8.0*12()<_CR><_LF>
1.6.0*09()<_CR><_LF> 1.8.0*13()<_CR><_LF>
1.6.0*10()<_CR><_LF> 1.8.0*14()<_CR><_LF>
1.6.0*11()<_CR><_LF> 1.8.0*15()<_CR><_LF>
1.6.0*12()<_CR><_LF> 1.8.1(00000.9 kWh)<_CR><_LF>
1.6.0*13()<_CR><_LF> 1.8.1*01(00000.8 kWh)<_CR><_LF>
1.6.0*14()<_CR><_LF> 1.8.1*02(00000.0 kWh)<_CR><_LF>
1.6.0*15()<_CR><_LF> 1.8.1*03(00000.0 kWh)<_CR><_LF>
1.6.1*01(0.0516 kW)(0060116083000)<_CR><_LF> 1.8.1*04()<_CR><_LF>
1.6.1*02(0.0500 kW)(0060116013000)<_CR><_LF> 1.8.1*05()<_CR><_LF>
1.6.1*03(0.0000 kW)(0000101000000)<_CR><_LF> 1.8.1*06()<_CR><_LF>
1.6.1*04()<_CR><_LF> 1.8.1*07()<_CR><_LF>
1.6.1*05()<_CR><_LF> 1.8.1*08()<_CR><_LF>
1.6.1*06()<_CR><_LF> 1.8.1*09()<_CR><_LF>
1.6.1*07()<_CR><_LF> 1.8.1*10()<_CR><_LF>
1.6.1*08()<_CR><_LF> 1.8.1*11()<_CR><_LF>
1.6.1*09()<_CR><_LF> 1.8.1*12()<_CR><_LF>
1.6.1*10()<_CR><_LF> 1.8.1*13()<_CR><_LF>
1.6.1*11()<_CR><_LF> 1.8.1*14()<_CR><_LF>
1.6.1*12()<_CR><_LF> 1.8.1*15()<_CR><_LF>
1.6.1*13()<_CR><_LF> 1.8.2(00000.0 kWh)<_CR><_LF>
1.6.1*14()<_CR><_LF> 1.8.2*01(00000.0 kWh)<_CR><_LF>
1.6.1*15()<_CR><_LF> 1.8.2*02(00000.0 kWh)<_CR><_LF>
1.6.2*01(0.0000 kW)(0000101000000)<_CR><_LF> 1.8.2*03(00000.0 kWh)<_CR><_LF>
1.6.2*02(0.0194 kW)(0060115213716)<_CR><_LF> 1.8.2*04()<_CR><_LF>
1.6.2*03(0.0992 kW)(0060115213000)<_CR><_LF> 1.8.2*05()<_CR><_LF>
1.6.2*04()<_CR><_LF> 1.8.2*06()<_CR><_LF>
1.6.2*05()<_CR><_LF> 1.8.2*07()<_CR><_LF>
1.6.2*06()<_CR><_LF> 1.8.2*08()<_CR><_LF>
1.6.2*07()<_CR><_LF> 1.8.2*09()<_CR><_LF>
1.6.2*08()<_CR><_LF> 1.8.2*10()<_CR><_LF>
1.6.2*09()<_CR><_LF> 1.8.2*11()<_CR><_LF>
1.6.2*10()<_CR><_LF> 1.8.2*12()<_CR><_LF>
1.6.2*11()<_CR><_LF> 1.8.2*13()<_CR><_LF>
1.6.2*12()<_CR><_LF> 1.8.2*14()<_CR><_LF>
1.6.2*13()<_CR><_LF> 1.8.2*15()<_CR><_LF>
1.6.2*14()<_CR><_LF> 21.8.0(00000.0 kWh)<_CR><_LF>
1.6.2*15()<_CR><_LF> 21.8.0*01(00000.0 kWh)<_CR><_LF>
9.6.0(0.4842 kVA)(0060116180000)<_CR><_LF> 21.8.0*02(00000.0 kWh)<_CR><_LF>
9.6.0*01(0.4766 kVA)(0060116020000)<_CR><_LF> 21.8.0*03(00000.0 kWh)<_CR><_LF>
9.6.0*02(0.4088 kVA)(0060116010000)<_CR><_LF> 21.8.0*04()<_CR><_LF>
9.6.0*03(0.5182 kVA)(0060115213000)<_CR><_LF> 21.8.0*05()<_CR><_LF>
9.6.0*04()<_CR><_LF> 21.8.0*06()<_CR><_LF>
9.6.0*05()<_CR><_LF> 21.8.0*07()<_CR><_LF>
9.6.0*06()<_CR><_LF> 21.8.0*08()<_CR><_LF>
9.6.0*07()<_CR><_LF> 21.8.0*09()<_CR><_LF>
9.6.0*08()<_CR><_LF> 21.8.0*10()<_CR><_LF>
9.6.0*09()<_CR><_LF> 21.8.0*11()<_CR><_LF>
Comm_des_MT830 1 14.11.12
21.8.0*12()<_CR><_LF> 3.8.0*14()<_CR><_LF>
21.8.0*13()<_CR><_LF> 3.8.0*15()<_CR><_LF>
21.8.0*14()<_CR><_LF> 23.8.0(00000.0 kvarh)<_CR><_LF>
21.8.0*15()<_CR><_LF> 23.8.0*01(00000.0 kvarh)<_CR><_LF>
41.8.0(00000.2 kWh)<_CR><_LF> 23.8.0*02(00000.0 kvarh)<_CR><_LF>
41.8.0*01(00000.2 kWh)<_CR><_LF> 23.8.0*03(00000.0 kvarh)<_CR><_LF>
41.8.0*02(00000.0 kWh)<_CR><_LF> 23.8.0*04()<_CR><_LF>
41.8.0*03(00000.0 kWh)<_CR><_LF> 23.8.0*05()<_CR><_LF>
41.8.0*04()<_CR><_LF> 23.8.0*06()<_CR><_LF>
41.8.0*05()<_CR><_LF> 23.8.0*07()<_CR><_LF>
41.8.0*06()<_CR><_LF> 23.8.0*08()<_CR><_LF>
41.8.0*07()<_CR><_LF> 23.8.0*09()<_CR><_LF>
41.8.0*08()<_CR><_LF> 23.8.0*10()<_CR><_LF>
41.8.0*09()<_CR><_LF> 23.8.0*11()<_CR><_LF>
41.8.0*10()<_CR><_LF> 23.8.0*12()<_CR><_LF>
41.8.0*11()<_CR><_LF> 23.8.0*13()<_CR><_LF>
41.8.0*12()<_CR><_LF> 23.8.0*14()<_CR><_LF>
41.8.0*13()<_CR><_LF> 23.8.0*15()<_CR><_LF>
41.8.0*14()<_CR><_LF> 43.8.0(00001.5 kvarh)<_CR><_LF>
41.8.0*15()<_CR><_LF> 43.8.0*01(00001.5 kvarh)<_CR><_LF>
61.8.0*02(00000.0 kWh)<_CR><_LF> 43.8.0*04()<_CR><_LF>
61.8.0*03(00000.0 kWh)<_CR><_LF> 43.8.0*05()<_CR><_LF>
61.8.0*04()<_CR><_LF> 43.8.0*06()<_CR><_LF>
61.8.0*05()<_CR><_LF> 43.8.0*07()<_CR><_LF>
61.8.0*06()<_CR><_LF> 43.8.0*08()<_CR><_LF>
61.8.0*07()<_CR><_LF> 43.8.0*09()<_CR><_LF>
61.8.0*08()<_CR><_LF> 43.8.0*10()<_CR><_LF>
61.8.0*09()<_CR><_LF> 43.8.0*11()<_CR><_LF>
61.8.0*10()<_CR><_LF> 43.8.0*12()<_CR><_LF>
61.8.0*11()<_CR><_LF> 43.8.0*13()<_CR><_LF>
61.8.0*12()<_CR><_LF> 43.8.0*14()<_CR><_LF>
61.8.0*13()<_CR><_LF> 43.8.0*15()<_CR><_LF>
61.8.0*14()<_CR><_LF> 63.8.0(00002.3 kvarh)<_CR><_LF>
61.8.0*15()<_CR><_LF> 63.8.0*01(00002.3 kvarh)<_CR><_LF>
2.8.0*02(00000.0 kWh)<_CR><_LF> 63.8.0*04()<_CR><_LF>
2.8.0*03(00000.0 kWh)<_CR><_LF> 63.8.0*05()<_CR><_LF>
2.8.0*04()<_CR><_LF> 63.8.0*06()<_CR><_LF>
2.8.0*05()<_CR><_LF> 63.8.0*07()<_CR><_LF>
2.8.0*06()<_CR><_LF> 63.8.0*08()<_CR><_LF>
2.8.0*07()<_CR><_LF> 63.8.0*09()<_CR><_LF>
2.8.0*08()<_CR><_LF> 63.8.0*10()<_CR><_LF>
2.8.0*09()<_CR><_LF> 63.8.0*11()<_CR><_LF>
2.8.0*10()<_CR><_LF> 63.8.0*12()<_CR><_LF>
2.8.0*11()<_CR><_LF> 63.8.0*13()<_CR><_LF>
2.8.0*12()<_CR><_LF> 63.8.0*14()<_CR><_LF>
2.8.0*13()<_CR><_LF> 63.8.0*15()<_CR><_LF>
2.8.0*14()<_CR><_LF> 4.8.0(00003.4 kvarh)<_CR><_LF>
2.8.0*15()<_CR><_LF> 4.8.0*01(00003.3 kvarh)<_CR><_LF>
3.8.0(00003.9 kvarh)<_CR><_LF> 4.8.0*02(00000.4 kvarh)<_CR><_LF>
3.8.0*01(00003.9 kvarh)<_CR><_LF> 4.8.0*03(00000.1 kvarh)<_CR><_LF>
3.8.0*02(00000.5 kvarh)<_CR><_LF> 4.8.0*04()<_CR><_LF>
3.8.0*03(00000.1 kvarh)<_CR><_LF> 4.8.0*05()<_CR><_LF>
3.8.0*04()<_CR><_LF> 4.8.0*06()<_CR><_LF>
3.8.0*05()<_CR><_LF> 4.8.0*07()<_CR><_LF>
3.8.0*06()<_CR><_LF> 4.8.0*08()<_CR><_LF>
3.8.0*07()<_CR><_LF> 4.8.0*09()<_CR><_LF>
3.8.0*08()<_CR><_LF> 4.8.0*10()<_CR><_LF>
3.8.0*09()<_CR><_LF> 4.8.0*11()<_CR><_LF>
3.8.0*10()<_CR><_LF> 4.8.0*12()<_CR><_LF>
3.8.0*11()<_CR><_LF> 4.8.0*13()<_CR><_LF>
3.8.0*12()<_CR><_LF> 4.8.0*14()<_CR><_LF>
3.8.0*13()<_CR><_LF> 4.8.0*15()<_CR><_LF>
Comm_des_MT830 2 14.11.12

5.8.0*02(00000.5 kvarh)<_CR><_LF> 7.8.0*04()<_CR><_LF>
5.8.0*03(00000.1 kvarh)<_CR><_LF> 7.8.0*05()<_CR><_LF>
5.8.0*04()<_CR><_LF> 7.8.0*06()<_CR><_LF>
5.8.0*05()<_CR><_LF> 7.8.0*07()<_CR><_LF>
5.8.0*06()<_CR><_LF> 7.8.0*08()<_CR><_LF>
5.8.0*07()<_CR><_LF> 7.8.0*09()<_CR><_LF>
5.8.0*08()<_CR><_LF> 7.8.0*10()<_CR><_LF>
5.8.0*09()<_CR><_LF> 7.8.0*11()<_CR><_LF>
5.8.0*10()<_CR><_LF> 7.8.0*12()<_CR><_LF>
5.8.0*11()<_CR><_LF> 7.8.0*13()<_CR><_LF>
5.8.0*12()<_CR><_LF> 7.8.0*14()<_CR><_LF>
5.8.0*13()<_CR><_LF> 7.8.0*15()<_CR><_LF>
5.8.0*14()<_CR><_LF> 8.8.0(00003.4 kvarh)<_CR><_LF>
5.8.0*15()<_CR><_LF> 8.8.0*01(00003.3 kvarh)<_CR><_LF>
5.8.1*02(00000.3 kvarh)<_CR><_LF> 8.8.0*04()<_CR><_LF>
5.8.1*03(00000.0 kvarh)<_CR><_LF> 8.8.0*05()<_CR><_LF>
5.8.1*04()<_CR><_LF> 8.8.0*06()<_CR><_LF>
5.8.1*05()<_CR><_LF> 8.8.0*07()<_CR><_LF>
5.8.1*06()<_CR><_LF> 8.8.0*08()<_CR><_LF>
5.8.1*07()<_CR><_LF> 8.8.0*09()<_CR><_LF>
5.8.1*08()<_CR><_LF> 8.8.0*10()<_CR><_LF>
5.8.1*09()<_CR><_LF> 8.8.0*11()<_CR><_LF>
5.8.1*10()<_CR><_LF> 8.8.0*12()<_CR><_LF>
5.8.1*11()<_CR><_LF> 8.8.0*13()<_CR><_LF>
5.8.1*12()<_CR><_LF> 8.8.0*14()<_CR><_LF>
5.8.1*13()<_CR><_LF> 8.8.0*15()<_CR><_LF>
5.8.1*14()<_CR><_LF> 8.8.1(00003.2 kvarh)<_CR><_LF>
5.8.1*15()<_CR><_LF> 8.8.1*01(00003.1 kvarh)<_CR><_LF>
5.8.2*02(00000.1 kvarh)<_CR><_LF> 8.8.1*04()<_CR><_LF>
5.8.2*03(00000.1 kvarh)<_CR><_LF> 8.8.1*05()<_CR><_LF>
5.8.2*04()<_CR><_LF> 8.8.1*06()<_CR><_LF>
5.8.2*05()<_CR><_LF> 8.8.1*07()<_CR><_LF>
5.8.2*06()<_CR><_LF> 8.8.1*08()<_CR><_LF>
5.8.2*07()<_CR><_LF> 8.8.1*09()<_CR><_LF>
5.8.2*08()<_CR><_LF> 8.8.1*10()<_CR><_LF>
5.8.2*09()<_CR><_LF> 8.8.1*11()<_CR><_LF>
5.8.2*10()<_CR><_LF> 8.8.1*12()<_CR><_LF>
5.8.2*11()<_CR><_LF> 8.8.1*13()<_CR><_LF>
5.8.2*12()<_CR><_LF> 8.8.1*14()<_CR><_LF>
5.8.2*13()<_CR><_LF> 8.8.1*15()<_CR><_LF>
5.8.2*14()<_CR><_LF> 8.8.2(00000.1 kvarh)<_CR><_LF>
5.8.2*15()<_CR><_LF> 8.8.2*01(00000.1 kvarh)<_CR><_LF>
6.8.0*02(00000.0 kvarh)<_CR><_LF> 8.8.2*04()<_CR><_LF>
6.8.0*03(00000.0 kvarh)<_CR><_LF> 8.8.2*05()<_CR><_LF>
6.8.0*04()<_CR><_LF> 8.8.2*06()<_CR><_LF>
6.8.0*05()<_CR><_LF> 8.8.2*07()<_CR><_LF>
6.8.0*06()<_CR><_LF> 8.8.2*08()<_CR><_LF>
6.8.0*07()<_CR><_LF> 8.8.2*09()<_CR><_LF>
6.8.0*08()<_CR><_LF> 8.8.2*10()<_CR><_LF>
6.8.0*09()<_CR><_LF> 8.8.2*11()<_CR><_LF>
6.8.0*10()<_CR><_LF> 8.8.2*12()<_CR><_LF>
6.8.0*11()<_CR><_LF> 8.8.2*13()<_CR><_LF>
6.8.0*12()<_CR><_LF> 8.8.2*14()<_CR><_LF>
6.8.0*13()<_CR><_LF> 8.8.2*15()<_CR><_LF>
6.8.0*14()<_CR><_LF> 9.8.0(00007.6 kVAh)<_CR><_LF>
6.8.0*15()<_CR><_LF> 9.8.0*01(00007.4 kVAh)<_CR><_LF>
7.8.0(00000.0 kvarh)<_CR><_LF> 9.8.0*02(00000.9 kVAh)<_CR><_LF>
7.8.0*01(00000.0 kvarh)<_CR><_LF> 9.8.0*03(00000.2 kVAh)<_CR><_LF>
Comm_des_MT830 3 14.11.12
9.8.0*04()<_CR><_LF> 33.7.0(0.033)<_CR><_LF>
9.8.0*05()<_CR><_LF> 53.7.0(1.000)<_CR><_LF>
9.8.0*06()<_CR><_LF> 73.7.0(0.013)<_CR><_LF>
9.8.0*07()<_CR><_LF> 14.7.0(49.9 Hz)<_CR><_LF>
9.8.0*08()<_CR><_LF> 81.7.40(88.0 deg)<_CR><_LF>
9.8.0*09()<_CR><_LF> 81.7.51(0.0 deg)<_CR><_LF>
9.8.0*10()<_CR><_LF> 81.7.62(89.2 deg)<_CR><_LF>
9.8.0*11()<_CR><_LF> !<_CR><_LF>
9.8.0*12()<_CR><_LF> <ETX>b
9.8.0*13()<_CR><_LF> 407 ms elapsed -> IEC1107 closing local connection
9.8.0*14()<_CR><_LF>
9.8.0*15()<_CR><_LF>
9.8.1(00007.2 kVAh)<_CR><_LF>
9.8.1*01(00007.1 kVAh)<_CR><_LF>
9.8.1*02(00000.6 kVAh)<_CR><_LF>
9.8.1*03(00000.0 kVAh)<_CR><_LF>
9.8.1*04()<_CR><_LF>
9.8.1*05()<_CR><_LF>
9.8.1*06()<_CR><_LF>
9.8.1*07()<_CR><_LF>
9.8.1*08()<_CR><_LF>
9.8.1*09()<_CR><_LF>
9.8.1*10()<_CR><_LF>
9.8.1*11()<_CR><_LF>
9.8.1*12()<_CR><_LF>
9.8.1*13()<_CR><_LF>
9.8.1*14()<_CR><_LF>
9.8.1*15()<_CR><_LF>
9.8.2(00000.3 kVAh)<_CR><_LF>
9.8.2*01(00000.3 kVAh)<_CR><_LF>
9.8.2*02(00000.3 kVAh)<_CR><_LF>
9.8.2*03(00000.2 kVAh)<_CR><_LF>
9.8.2*04()<_CR><_LF>
9.8.2*05()<_CR><_LF>
9.8.2*06()<_CR><_LF>
9.8.2*07()<_CR><_LF>
9.8.2*08()<_CR><_LF>
9.8.2*09()<_CR><_LF>
9.8.2*10()<_CR><_LF>
9.8.2*11()<_CR><_LF>
9.8.2*12()<_CR><_LF>
9.8.2*13()<_CR><_LF>
9.8.2*14()<_CR><_LF>
9.8.2*15()<_CR><_LF>
10.8.0(00000.0 kVAh)<_CR><_LF>
10.8.0*01(00000.0 kVAh)<_CR><_LF>
10.8.0*02(00000.0 kVAh)<_CR><_LF>
10.8.0*03(00000.0 kVAh)<_CR><_LF>
10.8.0*04()<_CR><_LF>
10.8.0*05()<_CR><_LF>
10.8.0*06()<_CR><_LF>
10.8.0*07()<_CR><_LF>
10.8.0*08()<_CR><_LF>
10.8.0*09()<_CR><_LF>
10.8.0*10()<_CR><_LF>
10.8.0*11()<_CR><_LF>
10.8.0*12()<_CR><_LF>
10.8.0*13()<_CR><_LF>
10.8.0*14()<_CR><_LF>
10.8.0*15()<_CR><_LF>
31.7.0(7.9 A)<_CR><_LF>
51.7.0(2.4 A)<_CR><_LF>
71.7.0(5.8 A)<_CR><_LF>
32.7.0(58.1 V)<_CR><_LF>
52.7.0(58.6 V)<_CR><_LF>
72.7.0(58.2 V)<_CR><_LF>
Comm_des_MT830 4 14.11.12
Energy measurement
Communication
Specification

password
62056-61

Comm_des_MT830 1 14.11.12
Data formats

y = 0: normal time
y = 2: UTC
Comm_des_MT830 2 14.11.12
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>R1<STX>0.0.128.3.4()<ETX>_
<SOH>B0<ETX>q
Comm_des_MT830 3 14.11.12
LB code Data name

LB.0080 Power down
LB.0040 Power up
LB.0020 RTC Set
LB.0008 DST
LB.8118 Watch dog
LB.8119 Fraud start
LB.811A Fraud end
Comm_des_MT830 4 14.11.12

LB.8152
LB.8154
LB.8155
LB.8157
Format:
Comm_des_MT830 5 14.11.12

LogBook Format :

(TSTs13)(Sn)
....
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
(0060115213109)(0040)<_CR><_LF>
(0060115213110)(811b)<_CR><_LF>
(0060115213112)(8105)<_CR><_LF>
(0060115213112)(8106)<_CR><_LF>
(0060115213112)(8107)<_CR><_LF>
(0060115213118)(0010)<_CR><_LF>
(0060115213625)(8102)<_CR><_LF>
(0060115213627)(8105)<_CR><_LF>
(0060115213630)(8102)<_CR><_LF>
(0060115213633)(8105)<_CR><_LF>
(0060115213648)(8102)<_CR><_LF>
(0060115213716)(0020)<_CR><_LF>
(0060115235716)(0020)<_CR><_LF>
<ETX>7
Comm_des_MT830 6 14.11.12
<SOH>B0<ETX>q

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>R5<STX>P.98(00601151700;00601152100)<ETX>&
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<ETX>W
<SOH>B0<ETX>q

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>
Comm_des_MT830 7 14.11.12

<ACK>
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<EOT>P
<ACK>
<STX>(0060115213109)(0040)<_CR><_LF>
(0060115213110)(811b)<_CR><_LF>
(0060115213112)(8105)<_CR><_LF>
(0060115213112)(8106)<_CR><_LF>
(0060115213112)(8107)<_CR><_LF>
(0060115213118)(0010)<_CR><_LF>
(0060115213625)(8102)<_CR><_LF>
(0060115213627)(8105)<_CR><_LF>
(0060115213630)(8102)<_CR><_LF>
(0060115213633)(8105)<_CR><_LF>
<EOT>U
<ACK>
<STX>(0060115213648)(8102)<_CR><_LF>
(0060115213716)(0020)<_CR><_LF>
(0060115235716)(0020)<_CR><_LF>
<ETX>2
<SOH>B0<ETX>q

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>
Comm_des_MT830 8 14.11.12

<ACK>051<_CR><_LF>

<ACK>
<SOH>R6<STX>P.98(00601151600;00601152100;5)<ETX>*
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
<EOT>2
<ACK>
<STX>(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<ETX>a
<SOH>B0<ETX>q
5. E2 command
Format:
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>
Comm_des_MT830 9 14.11.12

<ACK>051<_CR><_LF>

<ACK>
<SOH>E2<STX>0.0.5.0.4.0()<ETX>X
<ACK>
<SOH>B0<ETX>q
6. Load profile
Format:
Example:
23/08/2005 14:41:18, Log Started

/?!<_CR><_LF>
Comm_des_MT830 10 14.11.12

/ISK5MT830-1007<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(8b776701)<ETX>:
<ACK>
<SOH>R5<STX>P.01(00508221400;00508222100)<ETX>%
<STX>P.01(0050822143000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00047.713)(00001.367)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.6)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00047.935)(00001.373)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.5)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00048.161)(00001.380)(229.5)(229.6)(0.0)(19.6)<_CR><_LF>
(19.7)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
P.01(0050822160000)(10)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00048.423)(00001.387)(228.9)(229.0)(36.0)(18.8)<_CR><_LF>
(18.9)(2.0)(0.9995)(0.9993)(0.9999)<_CR><_LF>
P.01(0050822163000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00049.077)(00001.410)(228.9)(229.0)(228.9)(18.9)<_CR><_LF>
(19.2)(18.9)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00049.733)(00001.434)(228.9)(229.1)(228.9)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00050.397)(00001.457)(230.5)(230.7)(230.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.064)(00001.481)(230.6)(230.8)(230.6)(19.2)<_CR><_LF>
(19.4)(19.2)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.725)(00001.504)(229.5)(229.6)(229.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00052.383)(00001.528)(228.7)(228.8)(228.7)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.046)(00001.551)(229.4)(229.5)(229.4)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.704)(00001.575)(228.6)(228.7)(228.6)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00054.357)(00001.598)(227.6)(227.7)(227.6)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00055.014)(00001.622)(228.4)(228.6)(228.4)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<ETX>b
<SOH>B0<ETX>q
Comm_des_MT830 11 14.11.12
and with R6 command
23/08/2005 14:42:51, Log Started

/?!<_CR><_LF>

/ISK5MT830-1007<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>R6<STX>P.01(00508221400;00508222100;10)<ETX>\x1c
<STX>P.01(0050822143000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00047.713)(00001.367)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.6)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00047.935)(00001.373)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.5)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00048.161)(00001.380)(229.5)(229.6)(0.0)(19.6)<_CR><_LF>
(19.7)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
P.01(0050822160000)(10)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00048.423)(00001.387)(228.9)(229.0)(36.0)(18.8)<_CR><_LF>
(18.9)(2.0)(0.9995)(0.9993)(0.9999)<_CR><_LF>
P.01(0050822163000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00049.077)(00001.410)(228.9)(229.0)(228.9)(18.9)<_CR><_LF>
(19.2)(18.9)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00049.733)(00001.434)(228.9)(229.1)(228.9)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00050.397)(00001.457)(230.5)(230.7)(230.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.064)(00001.481)(230.6)(230.8)(230.6)(19.2)<_CR><_LF>
(19.4)(19.2)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.725)(00001.504)(229.5)(229.6)(229.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00052.383)(00001.528)(228.7)(228.8)(228.7)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<EOT>h
<ACK>
Comm_des_MT830 12 14.11.12

<STX>P.01(0050822193000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00053.046)(00001.551)(229.4)(229.5)(229.4)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.704)(00001.575)(228.6)(228.7)(228.6)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00054.357)(00001.598)(227.6)(227.7)(227.6)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00055.014)(00001.622)(228.4)(228.6)(228.4)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<ETX>^
<SOH>B0<ETX>q
Examples:
23/08/2007 14:41:18, Log Started

/?!<_CR><_LF>
Comm_des_MT830 13 14.11.12
/ISK5MT830-1034<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(8b776701)<ETX>:
<ACK>
(2.8)<_CR><_LF>
(kWh)<_CR><_LF>
(3.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(4.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(00045.700)(00000.000)(00002.000)(00000.000)<_CR><_LF>
P.01<_CR><_LF>
(0709232200)<_CR><_LF>
(00)<_CR><_LF>
(30)<_CR><_LF>
(4)<_CR><_LF>
(1.8)<_CR><_LF>
(kWh)<_CR><_LF>
(2.8)<_CR><_LF>
(kWh)<_CR><_LF>
(3.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(4.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(00046.793)(00000.000)(00002.047)(00000.000)<_CR><_LF>
(00047.888)(00000.000)(00002.095)(00000.000)<_CR><_LF>
(00048.992)(00000.000)(00002.143)(00000.000)<_CR><_LF>
(00050.089)(00000.000)(00002.190)(00000.000)<_CR><_LF>
(00051.146)(00000.000)(00002.234)(00000.000)<_CR><_LF>
<ETX><EOT>
<SOH>B0<ETX>q
Comm_des_MT830 14 14.11.12

Remark:

Remark:
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>W1<STX>0.9.1(123015)<ETX>Z
Comm_des_MT830 15 14.11.12
<ACK>
<SOH>W1<STX>0.9.2(060225)<ETX>^
<ACK>
<SOH>B0<ETX>q

Remark:

Remark:
Example:
/?!<_CR><_LF>

/ISK4MT860-1007<_CR><_LF>

<ACK>041<_CR><_LF>

<ACK>
<SOH>B0<ETX>q
Comm_des_MT830 16 14.11.12

Remark:
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>W1<STX>0.9.4(060117152508)<ETX>Q
<ACK>
<SOH>B0<ETX>q

Remark:
Comm_des_MT830 17 14.11.12
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>B0<ETX>q



Example:

Comm_des_MT830 18 14.11.12
/?!<_CR><_LF>

/ISK5MT830-1047<_CR><_LF>

<ACK>051<_CR><_LF>

<STX>(204522)<ETX><SOH>
<STX>(070925)<ETX>\x0b
<STX>(070925204531)<ETX><_LF>

<SOH>B0<ETX>q



Example:

Comm_des_MT830 19 14.11.12
/?!<_CR><_LF>

/ISK5MT830-1047<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(03767f47)<ETX>0
<STX>0.9.1(205448)<ETX>5
<STX>0.9.2(070925)<ETX>0
<STX>0.9.4(070925205454)<ETX>4
<SOH>B0<ETX>q
9. Data readout
the DRO sequence.
Example:
connection to 9600:
/?!<_CR><_LF> 0.9.2(060116)<_CR><_LF>
0.1.0(3)<_CR><_LF>
/ISK5MT830-1013<_CR><_LF> 0.1.2*02(0601160134)<_CR><_LF>
0.1.2*03(0601152131)<_CR><_LF>
<ACK>050<_CR><_LF> 0.1.2*05()<_CR><_LF>
0.1.2*06()<_CR><_LF>
Comm_des_MT830 20 14.11.12
0.1.2*07()<_CR><_LF> 9.6.0*10()<_CR><_LF>
0.1.2*08()<_CR><_LF> 9.6.0*11()<_CR><_LF>
0.1.2*09()<_CR><_LF> 9.6.0*12()<_CR><_LF>
0.1.2*10()<_CR><_LF> 9.6.0*13()<_CR><_LF>
0.1.2*11()<_CR><_LF> 9.6.0*14()<_CR><_LF>
0.1.2*12()<_CR><_LF> 9.6.0*15()<_CR><_LF>
0.1.2*13()<_CR><_LF> 1.8.0(00001.0 kWh)<_CR><_LF>
0.1.2*14()<_CR><_LF> 1.8.0*01(00000.9 kWh)<_CR><_LF>
0.1.2*15()<_CR><_LF> 1.8.0*02(00000.1 kWh)<_CR><_LF>
1.2.0(000.2008 kW)<_CR><_LF> 1.8.0*03(00000.0 kWh)<_CR><_LF>
1.6.0(0.0774 kW)(0060116180000)<_CR><_LF> 1.8.0*04()<_CR><_LF>
1.6.0*01(0.0516 kW)(0060116083000)<_CR><_LF> 1.8.0*05()<_CR><_LF>
1.6.0*02(0.0500 kW)(0060116013000)<_CR><_LF> 1.8.0*06()<_CR><_LF>
1.6.0*03(0.0992 kW)(0060115213000)<_CR><_LF> 1.8.0*07()<_CR><_LF>
1.6.0*04()<_CR><_LF> 1.8.0*08()<_CR><_LF>
1.6.0*05()<_CR><_LF> 1.8.0*09()<_CR><_LF>
1.6.0*06()<_CR><_LF> 1.8.0*10()<_CR><_LF>
1.6.0*07()<_CR><_LF> 1.8.0*11()<_CR><_LF>
1.6.0*08()<_CR><_LF> 1.8.0*12()<_CR><_LF>
1.6.0*09()<_CR><_LF> 1.8.0*13()<_CR><_LF>
1.6.0*10()<_CR><_LF> 1.8.0*14()<_CR><_LF>
1.6.0*11()<_CR><_LF> 1.8.0*15()<_CR><_LF>
1.6.0*12()<_CR><_LF> 1.8.1(00000.9 kWh)<_CR><_LF>
1.6.0*13()<_CR><_LF> 1.8.1*01(00000.8 kWh)<_CR><_LF>
1.6.0*14()<_CR><_LF> 1.8.1*02(00000.0 kWh)<_CR><_LF>
1.6.0*15()<_CR><_LF> 1.8.1*03(00000.0 kWh)<_CR><_LF>
1.6.1*01(0.0516 kW)(0060116083000)<_CR><_LF> 1.8.1*04()<_CR><_LF>
1.6.1*02(0.0500 kW)(0060116013000)<_CR><_LF> 1.8.1*05()<_CR><_LF>
1.6.1*03(0.0000 kW)(0000101000000)<_CR><_LF> 1.8.1*06()<_CR><_LF>
1.6.1*04()<_CR><_LF> 1.8.1*07()<_CR><_LF>
1.6.1*05()<_CR><_LF> 1.8.1*08()<_CR><_LF>
1.6.1*06()<_CR><_LF> 1.8.1*09()<_CR><_LF>
1.6.1*07()<_CR><_LF> 1.8.1*10()<_CR><_LF>
1.6.1*08()<_CR><_LF> 1.8.1*11()<_CR><_LF>
1.6.1*09()<_CR><_LF> 1.8.1*12()<_CR><_LF>
1.6.1*10()<_CR><_LF> 1.8.1*13()<_CR><_LF>
1.6.1*11()<_CR><_LF> 1.8.1*14()<_CR><_LF>
1.6.1*12()<_CR><_LF> 1.8.1*15()<_CR><_LF>
1.6.1*13()<_CR><_LF> 1.8.2(00000.0 kWh)<_CR><_LF>
1.6.1*14()<_CR><_LF> 1.8.2*01(00000.0 kWh)<_CR><_LF>
1.6.1*15()<_CR><_LF> 1.8.2*02(00000.0 kWh)<_CR><_LF>
1.6.2*01(0.0000 kW)(0000101000000)<_CR><_LF> 1.8.2*03(00000.0 kWh)<_CR><_LF>
1.6.2*02(0.0194 kW)(0060115213716)<_CR><_LF> 1.8.2*04()<_CR><_LF>
1.6.2*03(0.0992 kW)(0060115213000)<_CR><_LF> 1.8.2*05()<_CR><_LF>
1.6.2*04()<_CR><_LF> 1.8.2*06()<_CR><_LF>
1.6.2*05()<_CR><_LF> 1.8.2*07()<_CR><_LF>
1.6.2*06()<_CR><_LF> 1.8.2*08()<_CR><_LF>
1.6.2*07()<_CR><_LF> 1.8.2*09()<_CR><_LF>
1.6.2*08()<_CR><_LF> 1.8.2*10()<_CR><_LF>
1.6.2*09()<_CR><_LF> 1.8.2*11()<_CR><_LF>
1.6.2*10()<_CR><_LF> 1.8.2*12()<_CR><_LF>
1.6.2*11()<_CR><_LF> 1.8.2*13()<_CR><_LF>
1.6.2*12()<_CR><_LF> 1.8.2*14()<_CR><_LF>
1.6.2*13()<_CR><_LF> 1.8.2*15()<_CR><_LF>
1.6.2*14()<_CR><_LF> 21.8.0(00000.0 kWh)<_CR><_LF>
1.6.2*15()<_CR><_LF> 21.8.0*01(00000.0 kWh)<_CR><_LF>
9.6.0(0.4842 kVA)(0060116180000)<_CR><_LF> 21.8.0*02(00000.0 kWh)<_CR><_LF>
9.6.0*01(0.4766 kVA)(0060116020000)<_CR><_LF> 21.8.0*03(00000.0 kWh)<_CR><_LF>
9.6.0*02(0.4088 kVA)(0060116010000)<_CR><_LF> 21.8.0*04()<_CR><_LF>
9.6.0*03(0.5182 kVA)(0060115213000)<_CR><_LF> 21.8.0*05()<_CR><_LF>
9.6.0*04()<_CR><_LF> 21.8.0*06()<_CR><_LF>
9.6.0*05()<_CR><_LF> 21.8.0*07()<_CR><_LF>
9.6.0*06()<_CR><_LF> 21.8.0*08()<_CR><_LF>
9.6.0*07()<_CR><_LF> 21.8.0*09()<_CR><_LF>
9.6.0*08()<_CR><_LF> 21.8.0*10()<_CR><_LF>
9.6.0*09()<_CR><_LF> 21.8.0*11()<_CR><_LF>
Comm_des_MT830 1 14.11.12
21.8.0*12()<_CR><_LF> 3.8.0*14()<_CR><_LF>
21.8.0*13()<_CR><_LF> 3.8.0*15()<_CR><_LF>
21.8.0*14()<_CR><_LF> 23.8.0(00000.0 kvarh)<_CR><_LF>
21.8.0*15()<_CR><_LF> 23.8.0*01(00000.0 kvarh)<_CR><_LF>
41.8.0*02(00000.0 kWh)<_CR><_LF> 23.8.0*04()<_CR><_LF>
41.8.0*03(00000.0 kWh)<_CR><_LF> 23.8.0*05()<_CR><_LF>
41.8.0*04()<_CR><_LF> 23.8.0*06()<_CR><_LF>
41.8.0*05()<_CR><_LF> 23.8.0*07()<_CR><_LF>
41.8.0*06()<_CR><_LF> 23.8.0*08()<_CR><_LF>
41.8.0*07()<_CR><_LF> 23.8.0*09()<_CR><_LF>
41.8.0*08()<_CR><_LF> 23.8.0*10()<_CR><_LF>
41.8.0*09()<_CR><_LF> 23.8.0*11()<_CR><_LF>
41.8.0*10()<_CR><_LF> 23.8.0*12()<_CR><_LF>
41.8.0*11()<_CR><_LF> 23.8.0*13()<_CR><_LF>
41.8.0*12()<_CR><_LF> 23.8.0*14()<_CR><_LF>
41.8.0*13()<_CR><_LF> 23.8.0*15()<_CR><_LF>
41.8.0*14()<_CR><_LF> 43.8.0(00001.5 kvarh)<_CR><_LF>
41.8.0*15()<_CR><_LF> 43.8.0*01(00001.5 kvarh)<_CR><_LF>
61.8.0*02(00000.0 kWh)<_CR><_LF> 43.8.0*04()<_CR><_LF>
61.8.0*03(00000.0 kWh)<_CR><_LF> 43.8.0*05()<_CR><_LF>
61.8.0*04()<_CR><_LF> 43.8.0*06()<_CR><_LF>
61.8.0*05()<_CR><_LF> 43.8.0*07()<_CR><_LF>
61.8.0*06()<_CR><_LF> 43.8.0*08()<_CR><_LF>
61.8.0*07()<_CR><_LF> 43.8.0*09()<_CR><_LF>
61.8.0*08()<_CR><_LF> 43.8.0*10()<_CR><_LF>
61.8.0*09()<_CR><_LF> 43.8.0*11()<_CR><_LF>
61.8.0*10()<_CR><_LF> 43.8.0*12()<_CR><_LF>
61.8.0*11()<_CR><_LF> 43.8.0*13()<_CR><_LF>
61.8.0*12()<_CR><_LF> 43.8.0*14()<_CR><_LF>
61.8.0*13()<_CR><_LF> 43.8.0*15()<_CR><_LF>
61.8.0*14()<_CR><_LF> 63.8.0(00002.3 kvarh)<_CR><_LF>
61.8.0*15()<_CR><_LF> 63.8.0*01(00002.3 kvarh)<_CR><_LF>
2.8.0*02(00000.0 kWh)<_CR><_LF> 63.8.0*04()<_CR><_LF>
2.8.0*03(00000.0 kWh)<_CR><_LF> 63.8.0*05()<_CR><_LF>
2.8.0*04()<_CR><_LF> 63.8.0*06()<_CR><_LF>
2.8.0*05()<_CR><_LF> 63.8.0*07()<_CR><_LF>
2.8.0*06()<_CR><_LF> 63.8.0*08()<_CR><_LF>
2.8.0*07()<_CR><_LF> 63.8.0*09()<_CR><_LF>
2.8.0*08()<_CR><_LF> 63.8.0*10()<_CR><_LF>
2.8.0*09()<_CR><_LF> 63.8.0*11()<_CR><_LF>
2.8.0*10()<_CR><_LF> 63.8.0*12()<_CR><_LF>
2.8.0*11()<_CR><_LF> 63.8.0*13()<_CR><_LF>
2.8.0*12()<_CR><_LF> 63.8.0*14()<_CR><_LF>
2.8.0*13()<_CR><_LF> 63.8.0*15()<_CR><_LF>
2.8.0*14()<_CR><_LF> 4.8.0(00003.4 kvarh)<_CR><_LF>
2.8.0*15()<_CR><_LF> 4.8.0*01(00003.3 kvarh)<_CR><_LF>
3.8.0*02(00000.5 kvarh)<_CR><_LF> 4.8.0*04()<_CR><_LF>
3.8.0*03(00000.1 kvarh)<_CR><_LF> 4.8.0*05()<_CR><_LF>
3.8.0*04()<_CR><_LF> 4.8.0*06()<_CR><_LF>
3.8.0*05()<_CR><_LF> 4.8.0*07()<_CR><_LF>
3.8.0*06()<_CR><_LF> 4.8.0*08()<_CR><_LF>
3.8.0*07()<_CR><_LF> 4.8.0*09()<_CR><_LF>
3.8.0*08()<_CR><_LF> 4.8.0*10()<_CR><_LF>
3.8.0*09()<_CR><_LF> 4.8.0*11()<_CR><_LF>
3.8.0*10()<_CR><_LF> 4.8.0*12()<_CR><_LF>
3.8.0*11()<_CR><_LF> 4.8.0*13()<_CR><_LF>
3.8.0*12()<_CR><_LF> 4.8.0*14()<_CR><_LF>
3.8.0*13()<_CR><_LF> 4.8.0*15()<_CR><_LF>
Comm_des_MT830 2 14.11.12

5.8.0*02(00000.5 kvarh)<_CR><_LF> 7.8.0*04()<_CR><_LF>
5.8.0*03(00000.1 kvarh)<_CR><_LF> 7.8.0*05()<_CR><_LF>
5.8.0*04()<_CR><_LF> 7.8.0*06()<_CR><_LF>
5.8.0*05()<_CR><_LF> 7.8.0*07()<_CR><_LF>
5.8.0*06()<_CR><_LF> 7.8.0*08()<_CR><_LF>
5.8.0*07()<_CR><_LF> 7.8.0*09()<_CR><_LF>
5.8.0*08()<_CR><_LF> 7.8.0*10()<_CR><_LF>
5.8.0*09()<_CR><_LF> 7.8.0*11()<_CR><_LF>
5.8.0*10()<_CR><_LF> 7.8.0*12()<_CR><_LF>
5.8.0*11()<_CR><_LF> 7.8.0*13()<_CR><_LF>
5.8.0*12()<_CR><_LF> 7.8.0*14()<_CR><_LF>
5.8.0*13()<_CR><_LF> 7.8.0*15()<_CR><_LF>
5.8.0*14()<_CR><_LF> 8.8.0(00003.4 kvarh)<_CR><_LF>
5.8.0*15()<_CR><_LF> 8.8.0*01(00003.3 kvarh)<_CR><_LF>
5.8.1*02(00000.3 kvarh)<_CR><_LF> 8.8.0*04()<_CR><_LF>
5.8.1*03(00000.0 kvarh)<_CR><_LF> 8.8.0*05()<_CR><_LF>
5.8.1*04()<_CR><_LF> 8.8.0*06()<_CR><_LF>
5.8.1*05()<_CR><_LF> 8.8.0*07()<_CR><_LF>
5.8.1*06()<_CR><_LF> 8.8.0*08()<_CR><_LF>
5.8.1*07()<_CR><_LF> 8.8.0*09()<_CR><_LF>
5.8.1*08()<_CR><_LF> 8.8.0*10()<_CR><_LF>
5.8.1*09()<_CR><_LF> 8.8.0*11()<_CR><_LF>
5.8.1*10()<_CR><_LF> 8.8.0*12()<_CR><_LF>
5.8.1*11()<_CR><_LF> 8.8.0*13()<_CR><_LF>
5.8.1*12()<_CR><_LF> 8.8.0*14()<_CR><_LF>
5.8.1*13()<_CR><_LF> 8.8.0*15()<_CR><_LF>
5.8.1*14()<_CR><_LF> 8.8.1(00003.2 kvarh)<_CR><_LF>
5.8.1*15()<_CR><_LF> 8.8.1*01(00003.1 kvarh)<_CR><_LF>
5.8.2*02(00000.1 kvarh)<_CR><_LF> 8.8.1*04()<_CR><_LF>
5.8.2*03(00000.1 kvarh)<_CR><_LF> 8.8.1*05()<_CR><_LF>
5.8.2*04()<_CR><_LF> 8.8.1*06()<_CR><_LF>
5.8.2*05()<_CR><_LF> 8.8.1*07()<_CR><_LF>
5.8.2*06()<_CR><_LF> 8.8.1*08()<_CR><_LF>
5.8.2*07()<_CR><_LF> 8.8.1*09()<_CR><_LF>
5.8.2*08()<_CR><_LF> 8.8.1*10()<_CR><_LF>
5.8.2*09()<_CR><_LF> 8.8.1*11()<_CR><_LF>
5.8.2*10()<_CR><_LF> 8.8.1*12()<_CR><_LF>
5.8.2*11()<_CR><_LF> 8.8.1*13()<_CR><_LF>
5.8.2*12()<_CR><_LF> 8.8.1*14()<_CR><_LF>
5.8.2*13()<_CR><_LF> 8.8.1*15()<_CR><_LF>
5.8.2*14()<_CR><_LF> 8.8.2(00000.1 kvarh)<_CR><_LF>
5.8.2*15()<_CR><_LF> 8.8.2*01(00000.1 kvarh)<_CR><_LF>
6.8.0*02(00000.0 kvarh)<_CR><_LF> 8.8.2*04()<_CR><_LF>
6.8.0*03(00000.0 kvarh)<_CR><_LF> 8.8.2*05()<_CR><_LF>
6.8.0*04()<_CR><_LF> 8.8.2*06()<_CR><_LF>
6.8.0*05()<_CR><_LF> 8.8.2*07()<_CR><_LF>
6.8.0*06()<_CR><_LF> 8.8.2*08()<_CR><_LF>
6.8.0*07()<_CR><_LF> 8.8.2*09()<_CR><_LF>
6.8.0*08()<_CR><_LF> 8.8.2*10()<_CR><_LF>
6.8.0*09()<_CR><_LF> 8.8.2*11()<_CR><_LF>
6.8.0*10()<_CR><_LF> 8.8.2*12()<_CR><_LF>
6.8.0*11()<_CR><_LF> 8.8.2*13()<_CR><_LF>
6.8.0*12()<_CR><_LF> 8.8.2*14()<_CR><_LF>
6.8.0*13()<_CR><_LF> 8.8.2*15()<_CR><_LF>
6.8.0*14()<_CR><_LF> 9.8.0(00007.6 kVAh)<_CR><_LF>
6.8.0*15()<_CR><_LF> 9.8.0*01(00007.4 kVAh)<_CR><_LF>
Comm_des_MT830 3 14.11.12
9.8.0*04()<_CR><_LF> 33.7.0(0.033)<_CR><_LF>
9.8.0*05()<_CR><_LF> 53.7.0(1.000)<_CR><_LF>
9.8.0*06()<_CR><_LF> 73.7.0(0.013)<_CR><_LF>
9.8.0*07()<_CR><_LF> 14.7.0(49.9 Hz)<_CR><_LF>
9.8.0*08()<_CR><_LF> 81.7.40(88.0 deg)<_CR><_LF>
9.8.0*09()<_CR><_LF> 81.7.51(0.0 deg)<_CR><_LF>
9.8.0*10()<_CR><_LF> 81.7.62(89.2 deg)<_CR><_LF>
9.8.0*11()<_CR><_LF> !<_CR><_LF>
9.8.0*12()<_CR><_LF> <ETX>b
9.8.0*14()<_CR><_LF>
9.8.0*15()<_CR><_LF>
9.8.1(00007.2 kVAh)<_CR><_LF>
9.8.1*01(00007.1 kVAh)<_CR><_LF>
9.8.1*02(00000.6 kVAh)<_CR><_LF>
9.8.1*03(00000.0 kVAh)<_CR><_LF>
9.8.1*04()<_CR><_LF>
9.8.1*05()<_CR><_LF>
9.8.1*06()<_CR><_LF>
9.8.1*07()<_CR><_LF>
9.8.1*08()<_CR><_LF>
9.8.1*09()<_CR><_LF>
9.8.1*10()<_CR><_LF>
9.8.1*11()<_CR><_LF>
9.8.1*12()<_CR><_LF>
9.8.1*13()<_CR><_LF>
9.8.1*14()<_CR><_LF>
9.8.1*15()<_CR><_LF>
9.8.2(00000.3 kVAh)<_CR><_LF>
9.8.2*01(00000.3 kVAh)<_CR><_LF>
9.8.2*02(00000.3 kVAh)<_CR><_LF>
9.8.2*03(00000.2 kVAh)<_CR><_LF>
9.8.2*04()<_CR><_LF>
9.8.2*05()<_CR><_LF>
9.8.2*06()<_CR><_LF>
9.8.2*07()<_CR><_LF>
9.8.2*08()<_CR><_LF>
9.8.2*09()<_CR><_LF>
9.8.2*10()<_CR><_LF>
9.8.2*11()<_CR><_LF>
9.8.2*12()<_CR><_LF>
9.8.2*13()<_CR><_LF>
9.8.2*14()<_CR><_LF>
9.8.2*15()<_CR><_LF>
10.8.0(00000.0 kVAh)<_CR><_LF>
10.8.0*01(00000.0 kVAh)<_CR><_LF>
10.8.0*02(00000.0 kVAh)<_CR><_LF>
10.8.0*03(00000.0 kVAh)<_CR><_LF>
10.8.0*04()<_CR><_LF>
10.8.0*05()<_CR><_LF>
10.8.0*06()<_CR><_LF>
10.8.0*07()<_CR><_LF>
10.8.0*08()<_CR><_LF>
10.8.0*09()<_CR><_LF>
10.8.0*10()<_CR><_LF>
10.8.0*11()<_CR><_LF>
10.8.0*12()<_CR><_LF>
10.8.0*13()<_CR><_LF>
10.8.0*14()<_CR><_LF>
10.8.0*15()<_CR><_LF>
31.7.0(7.9 A)<_CR><_LF>
51.7.0(2.4 A)<_CR><_LF>
71.7.0(5.8 A)<_CR><_LF>
32.7.0(58.1 V)<_CR><_LF>
52.7.0(58.6 V)<_CR><_LF>
72.7.0(58.2 V)<_CR><_LF>
Comm_des_MT830 4 14.11.12
Energy measurement
Communication
Specification

password
62056-61

Comm_des_MT830 1 14.11.12
Data formats

y = 0: normal time
y = 2: UTC
Comm_des_MT830 2 14.11.12
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>R1<STX>0.0.128.3.4()<ETX>_
<SOH>B0<ETX>q
Comm_des_MT830 3 14.11.12
LB code Data name

LB.0080 Power down
LB.0040 Power up
LB.0020 RTC Set
LB.0008 DST
LB.8118 Watch dog
LB.8119 Fraud start
LB.811A Fraud end
Comm_des_MT830 4 14.11.12

LB.8152
LB.8154
LB.8155
LB.8157
Format:
Comm_des_MT830 5 14.11.12

LogBook Format :

(TSTs13)(Sn)
....
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
(0060115213109)(0040)<_CR><_LF>
(0060115213110)(811b)<_CR><_LF>
(0060115213112)(8105)<_CR><_LF>
(0060115213112)(8106)<_CR><_LF>
(0060115213112)(8107)<_CR><_LF>
(0060115213118)(0010)<_CR><_LF>
(0060115213625)(8102)<_CR><_LF>
(0060115213627)(8105)<_CR><_LF>
(0060115213630)(8102)<_CR><_LF>
(0060115213633)(8105)<_CR><_LF>
(0060115213648)(8102)<_CR><_LF>
(0060115213716)(0020)<_CR><_LF>
(0060115235716)(0020)<_CR><_LF>
<ETX>7
Comm_des_MT830 6 14.11.12
<SOH>B0<ETX>q

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>R5<STX>P.98(00601151700;00601152100)<ETX>&
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<ETX>W
<SOH>B0<ETX>q

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>
Comm_des_MT830 7 14.11.12

<ACK>
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<EOT>P
<ACK>
<STX>(0060115213109)(0040)<_CR><_LF>
(0060115213110)(811b)<_CR><_LF>
(0060115213112)(8105)<_CR><_LF>
(0060115213112)(8106)<_CR><_LF>
(0060115213112)(8107)<_CR><_LF>
(0060115213118)(0010)<_CR><_LF>
(0060115213625)(8102)<_CR><_LF>
(0060115213627)(8105)<_CR><_LF>
(0060115213630)(8102)<_CR><_LF>
(0060115213633)(8105)<_CR><_LF>
<EOT>U
<ACK>
<STX>(0060115213648)(8102)<_CR><_LF>
(0060115213716)(0020)<_CR><_LF>
(0060115235716)(0020)<_CR><_LF>
<ETX>2
<SOH>B0<ETX>q

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>
Comm_des_MT830 8 14.11.12

<ACK>051<_CR><_LF>

<ACK>
<SOH>R6<STX>P.98(00601151600;00601152100;5)<ETX>*
<STX>(0060115205704)(811f)<_CR><_LF>
(0060115205706)(811b)<_CR><_LF>
(0060115205709)(8105)<_CR><_LF>
(0060115205709)(8106)<_CR><_LF>
(0060115205709)(8107)<_CR><_LF>
<EOT>2
<ACK>
<STX>(0060115205715)(8120)<_CR><_LF>
(0060115205717)(811b)<_CR><_LF>
(0060115205719)(8105)<_CR><_LF>
(0060115205719)(8106)<_CR><_LF>
(0060115205719)(8107)<_CR><_LF>
<ETX>a
<SOH>B0<ETX>q
5. E2 command
Format:
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>
Comm_des_MT830 9 14.11.12

<ACK>051<_CR><_LF>

<ACK>
<SOH>E2<STX>0.0.5.0.4.0()<ETX>X
<ACK>
<SOH>B0<ETX>q
6. Load profile
Format:
Example:
23/08/2005 14:41:18, Log Started

/?!<_CR><_LF>
Comm_des_MT830 10 14.11.12

/ISK5MT830-1007<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(8b776701)<ETX>:
<ACK>
<SOH>R5<STX>P.01(00508221400;00508222100)<ETX>%
<STX>P.01(0050822143000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00047.713)(00001.367)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.6)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00047.935)(00001.373)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.5)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00048.161)(00001.380)(229.5)(229.6)(0.0)(19.6)<_CR><_LF>
(19.7)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
P.01(0050822160000)(10)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00048.423)(00001.387)(228.9)(229.0)(36.0)(18.8)<_CR><_LF>
(18.9)(2.0)(0.9995)(0.9993)(0.9999)<_CR><_LF>
P.01(0050822163000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00049.077)(00001.410)(228.9)(229.0)(228.9)(18.9)<_CR><_LF>
(19.2)(18.9)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00049.733)(00001.434)(228.9)(229.1)(228.9)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00050.397)(00001.457)(230.5)(230.7)(230.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.064)(00001.481)(230.6)(230.8)(230.6)(19.2)<_CR><_LF>
(19.4)(19.2)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.725)(00001.504)(229.5)(229.6)(229.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00052.383)(00001.528)(228.7)(228.8)(228.7)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.046)(00001.551)(229.4)(229.5)(229.4)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.704)(00001.575)(228.6)(228.7)(228.6)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00054.357)(00001.598)(227.6)(227.7)(227.6)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00055.014)(00001.622)(228.4)(228.6)(228.4)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<ETX>b
<SOH>B0<ETX>q
Comm_des_MT830 11 14.11.12
and with R6 command
23/08/2005 14:42:51, Log Started

/?!<_CR><_LF>

/ISK5MT830-1007<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>R6<STX>P.01(00508221400;00508222100;10)<ETX>\x1c
<STX>P.01(0050822143000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00047.713)(00001.367)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.6)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00047.935)(00001.373)(228.0)(228.2)(0.0)(19.5)<_CR><_LF>
(19.5)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
(00048.161)(00001.380)(229.5)(229.6)(0.0)(19.6)<_CR><_LF>
(19.7)(0.0)(0.9995)(0.9993)(1.0000)<_CR><_LF>
P.01(0050822160000)(10)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00048.423)(00001.387)(228.9)(229.0)(36.0)(18.8)<_CR><_LF>
(18.9)(2.0)(0.9995)(0.9993)(0.9999)<_CR><_LF>
P.01(0050822163000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00049.077)(00001.410)(228.9)(229.0)(228.9)(18.9)<_CR><_LF>
(19.2)(18.9)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00049.733)(00001.434)(228.9)(229.1)(228.9)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00050.397)(00001.457)(230.5)(230.7)(230.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.064)(00001.481)(230.6)(230.8)(230.6)(19.2)<_CR><_LF>
(19.4)(19.2)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00051.725)(00001.504)(229.5)(229.6)(229.5)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00052.383)(00001.528)(228.7)(228.8)(228.7)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<EOT>h
<ACK>
Comm_des_MT830 12 14.11.12

<STX>P.01(0050822193000)(00)(30)(11)<_CR><_LF>
(51.5)( A)(71.5)( A)(33.5)( )(53.5)( )(73.5)( )<_CR><_LF>
(00053.046)(00001.551)(229.4)(229.5)(229.4)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00053.704)(00001.575)(228.6)(228.7)(228.6)(19.1)<_CR><_LF>
(19.4)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00054.357)(00001.598)(227.6)(227.7)(227.6)(19.0)<_CR><_LF>
(19.3)(19.0)(0.9995)(0.9993)(0.9991)<_CR><_LF>
(00055.014)(00001.622)(228.4)(228.6)(228.4)(19.1)<_CR><_LF>
(19.3)(19.1)(0.9995)(0.9993)(0.9991)<_CR><_LF>
<ETX>^
<SOH>B0<ETX>q
Examples:
23/08/2007 14:41:18, Log Started

/?!<_CR><_LF>
Comm_des_MT830 13 14.11.12
/ISK5MT830-1034<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(8b776701)<ETX>:
<ACK>
(2.8)<_CR><_LF>
(kWh)<_CR><_LF>
(3.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(4.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(00045.700)(00000.000)(00002.000)(00000.000)<_CR><_LF>
P.01<_CR><_LF>
(0709232200)<_CR><_LF>
(00)<_CR><_LF>
(30)<_CR><_LF>
(4)<_CR><_LF>
(1.8)<_CR><_LF>
(kWh)<_CR><_LF>
(2.8)<_CR><_LF>
(kWh)<_CR><_LF>
(3.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(4.8)<_CR><_LF>
(kvarh)<_CR><_LF>
(00046.793)(00000.000)(00002.047)(00000.000)<_CR><_LF>
(00047.888)(00000.000)(00002.095)(00000.000)<_CR><_LF>
(00048.992)(00000.000)(00002.143)(00000.000)<_CR><_LF>
(00050.089)(00000.000)(00002.190)(00000.000)<_CR><_LF>
(00051.146)(00000.000)(00002.234)(00000.000)<_CR><_LF>
<ETX><EOT>
<SOH>B0<ETX>q
Comm_des_MT830 14 14.11.12

Remark:

Remark:
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>W1<STX>0.9.1(123015)<ETX>Z
Comm_des_MT830 15 14.11.12
<ACK>
<SOH>W1<STX>0.9.2(060225)<ETX>^
<ACK>
<SOH>B0<ETX>q

Remark:

Remark:
Example:
/?!<_CR><_LF>

/ISK4MT860-1007<_CR><_LF>

<ACK>041<_CR><_LF>

<ACK>
<SOH>B0<ETX>q
Comm_des_MT830 16 14.11.12

Remark:
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>W1<STX>0.9.4(060117152508)<ETX>Q
<ACK>
<SOH>B0<ETX>q

Remark:
Comm_des_MT830 17 14.11.12
Example:

/?!<_CR><_LF>

/ISK5MT830-1013<_CR><_LF>

<ACK>051<_CR><_LF>

<ACK>
<SOH>B0<ETX>q



Example:

Comm_des_MT830 18 14.11.12
/?!<_CR><_LF>

/ISK5MT830-1047<_CR><_LF>

<ACK>051<_CR><_LF>

<STX>(204522)<ETX><SOH>
<STX>(070925)<ETX>\x0b
<STX>(070925204531)<ETX><_LF>

<SOH>B0<ETX>q



Example:

Comm_des_MT830 19 14.11.12
/?!<_CR><_LF>

/ISK5MT830-1047<_CR><_LF>

<ACK>051<_CR><_LF>

<SOH>P0<STX>(03767f47)<ETX>0
<STX>0.9.1(205448)<ETX>5
<STX>0.9.2(070925)<ETX>0
<STX>0.9.4(070925205454)<ETX>4
<SOH>B0<ETX>q
9. Data readout
the DRO sequence.
Example:
connection to 9600:
/?!<_CR><_LF> 0.9.2(060116)<_CR><_LF>
0.1.0(3)<_CR><_LF>
/ISK5MT830-1013<_CR><_LF> 0.1.2*02(0601160134)<_CR><_LF>
0.1.2*03(0601152131)<_CR><_LF>
<ACK>050<_CR><_LF> 0.1.2*05()<_CR><_LF>
0.1.2*06()<_CR><_LF>
Comm_des_MT830 20 14.11.12
0.1.2*07()<_CR><_LF> 9.6.0*10()<_CR><_LF>
0.1.2*08()<_CR><_LF> 9.6.0*11()<_CR><_LF>
0.1.2*09()<_CR><_LF> 9.6.0*12()<_CR><_LF>
0.1.2*10()<_CR><_LF> 9.6.0*13()<_CR><_LF>
0.1.2*11()<_CR><_LF> 9.6.0*14()<_CR><_LF>
0.1.2*12()<_CR><_LF> 9.6.0*15()<_CR><_LF>
0.1.2*13()<_CR><_LF> 1.8.0(00001.0 kWh)<_CR><_LF>
0.1.2*14()<_CR><_LF> 1.8.0*01(00000.9 kWh)<_CR><_LF>
0.1.2*15()<_CR><_LF> 1.8.0*02(00000.1 kWh)<_CR><_LF>
1.2.0(000.2008 kW)<_CR><_LF> 1.8.0*03(00000.0 kWh)<_CR><_LF>
1.6.0(0.0774 kW)(0060116180000)<_CR><_LF> 1.8.0*04()<_CR><_LF>
1.6.0*01(0.0516 kW)(0060116083000)<_CR><_LF> 1.8.0*05()<_CR><_LF>
1.6.0*02(0.0500 kW)(0060116013000)<_CR><_LF> 1.8.0*06()<_CR><_LF>
1.6.0*03(0.0992 kW)(0060115213000)<_CR><_LF> 1.8.0*07()<_CR><_LF>
1.6.0*04()<_CR><_LF> 1.8.0*08()<_CR><_LF>
1.6.0*05()<_CR><_LF> 1.8.0*09()<_CR><_LF>
1.6.0*06()<_CR><_LF> 1.8.0*10()<_CR><_LF>
1.6.0*07()<_CR><_LF> 1.8.0*11()<_CR><_LF>
1.6.0*08()<_CR><_LF> 1.8.0*12()<_CR><_LF>
1.6.0*09()<_CR><_LF> 1.8.0*13()<_CR><_LF>
1.6.0*10()<_CR><_LF> 1.8.0*14()<_CR><_LF>
1.6.0*11()<_CR><_LF> 1.8.0*15()<_CR><_LF>
1.6.0*12()<_CR><_LF> 1.8.1(00000.9 kWh)<_CR><_LF>
1.6.0*13()<_CR><_LF> 1.8.1*01(00000.8 kWh)<_CR><_LF>
1.6.0*14()<_CR><_LF> 1.8.1*02(00000.0 kWh)<_CR><_LF>
1.6.0*15()<_CR><_LF> 1.8.1*03(00000.0 kWh)<_CR><_LF>
1.6.1*01(0.0516 kW)(0060116083000)<_CR><_LF> 1.8.1*04()<_CR><_LF>
1.6.1*02(0.0500 kW)(0060116013000)<_CR><_LF> 1.8.1*05()<_CR><_LF>
1.6.1*03(0.0000 kW)(0000101000000)<_CR><_LF> 1.8.1*06()<_CR><_LF>
1.6.1*04()<_CR><_LF> 1.8.1*07()<_CR><_LF>
1.6.1*05()<_CR><_LF> 1.8.1*08()<_CR><_LF>
1.6.1*06()<_CR><_LF> 1.8.1*09()<_CR><_LF>
1.6.1*07()<_CR><_LF> 1.8.1*10()<_CR><_LF>
1.6.1*08()<_CR><_LF> 1.8.1*11()<_CR><_LF>
1.6.1*09()<_CR><_LF> 1.8.1*12()<_CR><_LF>
1.6.1*10()<_CR><_LF> 1.8.1*13()<_CR><_LF>
1.6.1*11()<_CR><_LF> 1.8.1*14()<_CR><_LF>
1.6.1*12()<_CR><_LF> 1.8.1*15()<_CR><_LF>
1.6.1*13()<_CR><_LF> 1.8.2(00000.0 kWh)<_CR><_LF>
1.6.1*14()<_CR><_LF> 1.8.2*01(00000.0 kWh)<_CR><_LF>
1.6.1*15()<_CR><_LF> 1.8.2*02(00000.0 kWh)<_CR><_LF>
1.6.2*01(0.0000 kW)(0000101000000)<_CR><_LF> 1.8.2*03(00000.0 kWh)<_CR><_LF>
1.6.2*02(0.0194 kW)(0060115213716)<_CR><_LF> 1.8.2*04()<_CR><_LF>
1.6.2*03(0.0992 kW)(0060115213000)<_CR><_LF> 1.8.2*05()<_CR><_LF>
1.6.2*04()<_CR><_LF> 1.8.2*06()<_CR><_LF>
1.6.2*05()<_CR><_LF> 1.8.2*07()<_CR><_LF>
1.6.2*06()<_CR><_LF> 1.8.2*08()<_CR><_LF>
1.6.2*07()<_CR><_LF> 1.8.2*09()<_CR><_LF>
1.6.2*08()<_CR><_LF> 1.8.2*10()<_CR><_LF>
1.6.2*09()<_CR><_LF> 1.8.2*11()<_CR><_LF>
1.6.2*10()<_CR><_LF> 1.8.2*12()<_CR><_LF>
1.6.2*11()<_CR><_LF> 1.8.2*13()<_CR><_LF>
1.6.2*12()<_CR><_LF> 1.8.2*14()<_CR><_LF>
1.6.2*13()<_CR><_LF> 1.8.2*15()<_CR><_LF>
1.6.2*14()<_CR><_LF> 21.8.0(00000.0 kWh)<_CR><_LF>
1.6.2*15()<_CR><_LF> 21.8.0*01(00000.0 kWh)<_CR><_LF>
9.6.0(0.4842 kVA)(0060116180000)<_CR><_LF> 21.8.0*02(00000.0 kWh)<_CR><_LF>
9.6.0*01(0.4766 kVA)(0060116020000)<_CR><_LF> 21.8.0*03(00000.0 kWh)<_CR><_LF>
9.6.0*02(0.4088 kVA)(0060116010000)<_CR><_LF> 21.8.0*04()<_CR><_LF>
9.6.0*03(0.5182 kVA)(0060115213000)<_CR><_LF> 21.8.0*05()<_CR><_LF>
9.6.0*04()<_CR><_LF> 21.8.0*06()<_CR><_LF>
9.6.0*05()<_CR><_LF> 21.8.0*07()<_CR><_LF>
9.6.0*06()<_CR><_LF> 21.8.0*08()<_CR><_LF>
9.6.0*07()<_CR><_LF> 21.8.0*09()<_CR><_LF>
9.6.0*08()<_CR><_LF> 21.8.0*10()<_CR><_LF>
9.6.0*09()<_CR><_LF> 21.8.0*11()<_CR><_LF>
Comm_des_MT830 1 14.11.12
21.8.0*12()<_CR><_LF> 3.8.0*14()<_CR><_LF>
21.8.0*13()<_CR><_LF> 3.8.0*15()<_CR><_LF>
21.8.0*14()<_CR><_LF> 23.8.0(00000.0 kvarh)<_CR><_LF>
21.8.0*15()<_CR><_LF> 23.8.0*01(00000.0 kvarh)<_CR><_LF>
41.8.0*02(00000.0 kWh)<_CR><_LF> 23.8.0*04()<_CR><_LF>
41.8.0*03(00000.0 kWh)<_CR><_LF> 23.8.0*05()<_CR><_LF>
41.8.0*04()<_CR><_LF> 23.8.0*06()<_CR><_LF>
41.8.0*05()<_CR><_LF> 23.8.0*07()<_CR><_LF>
41.8.0*06()<_CR><_LF> 23.8.0*08()<_CR><_LF>
41.8.0*07()<_CR><_LF> 23.8.0*09()<_CR><_LF>
41.8.0*08()<_CR><_LF> 23.8.0*10()<_CR><_LF>
41.8.0*09()<_CR><_LF> 23.8.0*11()<_CR><_LF>
41.8.0*10()<_CR><_LF> 23.8.0*12()<_CR><_LF>
41.8.0*11()<_CR><_LF> 23.8.0*13()<_CR><_LF>
41.8.0*12()<_CR><_LF> 23.8.0*14()<_CR><_LF>
41.8.0*13()<_CR><_LF> 23.8.0*15()<_CR><_LF>
41.8.0*14()<_CR><_LF> 43.8.0(00001.5 kvarh)<_CR><_LF>
41.8.0*15()<_CR><_LF> 43.8.0*01(00001.5 kvarh)<_CR><_LF>
61.8.0*02(00000.0 kWh)<_CR><_LF> 43.8.0*04()<_CR><_LF>
61.8.0*03(00000.0 kWh)<_CR><_LF> 43.8.0*05()<_CR><_LF>
61.8.0*04()<_CR><_LF> 43.8.0*06()<_CR><_LF>
61.8.0*05()<_CR><_LF> 43.8.0*07()<_CR><_LF>
61.8.0*06()<_CR><_LF> 43.8.0*08()<_CR><_LF>
61.8.0*07()<_CR><_LF> 43.8.0*09()<_CR><_LF>
61.8.0*08()<_CR><_LF> 43.8.0*10()<_CR><_LF>
61.8.0*09()<_CR><_LF> 43.8.0*11()<_CR><_LF>
61.8.0*10()<_CR><_LF> 43.8.0*12()<_CR><_LF>
61.8.0*11()<_CR><_LF> 43.8.0*13()<_CR><_LF>
61.8.0*12()<_CR><_LF> 43.8.0*14()<_CR><_LF>
61.8.0*13()<_CR><_LF> 43.8.0*15()<_CR><_LF>
61.8.0*14()<_CR><_LF> 63.8.0(00002.3 kvarh)<_CR><_LF>
61.8.0*15()<_CR><_LF> 63.8.0*01(00002.3 kvarh)<_CR><_LF>
2.8.0*02(00000.0 kWh)<_CR><_LF> 63.8.0*04()<_CR><_LF>
2.8.0*03(00000.0 kWh)<_CR><_LF> 63.8.0*05()<_CR><_LF>
2.8.0*04()<_CR><_LF> 63.8.0*06()<_CR><_LF>
2.8.0*05()<_CR><_LF> 63.8.0*07()<_CR><_LF>
2.8.0*06()<_CR><_LF> 63.8.0*08()<_CR><_LF>
2.8.0*07()<_CR><_LF> 63.8.0*09()<_CR><_LF>
2.8.0*08()<_CR><_LF> 63.8.0*10()<_CR><_LF>
2.8.0*09()<_CR><_LF> 63.8.0*11()<_CR><_LF>
2.8.0*10()<_CR><_LF> 63.8.0*12()<_CR><_LF>
2.8.0*11()<_CR><_LF> 63.8.0*13()<_CR><_LF>
2.8.0*12()<_CR><_LF> 63.8.0*14()<_CR><_LF>
2.8.0*13()<_CR><_LF> 63.8.0*15()<_CR><_LF>
2.8.0*14()<_CR><_LF> 4.8.0(00003.4 kvarh)<_CR><_LF>
2.8.0*15()<_CR><_LF> 4.8.0*01(00003.3 kvarh)<_CR><_LF>
3.8.0*02(00000.5 kvarh)<_CR><_LF> 4.8.0*04()<_CR><_LF>
3.8.0*03(00000.1 kvarh)<_CR><_LF> 4.8.0*05()<_CR><_LF>
3.8.0*04()<_CR><_LF> 4.8.0*06()<_CR><_LF>
3.8.0*05()<_CR><_LF> 4.8.0*07()<_CR><_LF>
3.8.0*06()<_CR><_LF> 4.8.0*08()<_CR><_LF>
3.8.0*07()<_CR><_LF> 4.8.0*09()<_CR><_LF>
3.8.0*08()<_CR><_LF> 4.8.0*10()<_CR><_LF>
3.8.0*09()<_CR><_LF> 4.8.0*11()<_CR><_LF>
3.8.0*10()<_CR><_LF> 4.8.0*12()<_CR><_LF>
3.8.0*11()<_CR><_LF> 4.8.0*13()<_CR><_LF>
3.8.0*12()<_CR><_LF> 4.8.0*14()<_CR><_LF>
3.8.0*13()<_CR><_LF> 4.8.0*15()<_CR><_LF>
Comm_des_MT830 2 14.11.12

5.8.0*02(00000.5 kvarh)<_CR><_LF> 7.8.0*04()<_CR><_LF>
5.8.0*03(00000.1 kvarh)<_CR><_LF> 7.8.0*05()<_CR><_LF>
5.8.0*04()<_CR><_LF> 7.8.0*06()<_CR><_LF>
5.8.0*05()<_CR><_LF> 7.8.0*07()<_CR><_LF>
5.8.0*06()<_CR><_LF> 7.8.0*08()<_CR><_LF>
5.8.0*07()<_CR><_LF> 7.8.0*09()<_CR><_LF>
5.8.0*08()<_CR><_LF> 7.8.0*10()<_CR><_LF>
5.8.0*09()<_CR><_LF> 7.8.0*11()<_CR><_LF>
5.8.0*10()<_CR><_LF> 7.8.0*12()<_CR><_LF>
5.8.0*11()<_CR><_LF> 7.8.0*13()<_CR><_LF>
5.8.0*12()<_CR><_LF> 7.8.0*14()<_CR><_LF>
5.8.0*13()<_CR><_LF> 7.8.0*15()<_CR><_LF>
5.8.0*14()<_CR><_LF> 8.8.0(00003.4 kvarh)<_CR><_LF>
5.8.0*15()<_CR><_LF> 8.8.0*01(00003.3 kvarh)<_CR><_LF>
5.8.1*02(00000.3 kvarh)<_CR><_LF> 8.8.0*04()<_CR><_LF>
5.8.1*03(00000.0 kvarh)<_CR><_LF> 8.8.0*05()<_CR><_LF>
5.8.1*04()<_CR><_LF> 8.8.0*06()<_CR><_LF>
5.8.1*05()<_CR><_LF> 8.8.0*07()<_CR><_LF>
5.8.1*06()<_CR><_LF> 8.8.0*08()<_CR><_LF>
5.8.1*07()<_CR><_LF> 8.8.0*09()<_CR><_LF>
5.8.1*08()<_CR><_LF> 8.8.0*10()<_CR><_LF>
5.8.1*09()<_CR><_LF> 8.8.0*11()<_CR><_LF>
5.8.1*10()<_CR><_LF> 8.8.0*12()<_CR><_LF>
5.8.1*11()<_CR><_LF> 8.8.0*13()<_CR><_LF>
5.8.1*12()<_CR><_LF> 8.8.0*14()<_CR><_LF>
5.8.1*13()<_CR><_LF> 8.8.0*15()<_CR><_LF>
5.8.1*14()<_CR><_LF> 8.8.1(00003.2 kvarh)<_CR><_LF>
5.8.1*15()<_CR><_LF> 8.8.1*01(00003.1 kvarh)<_CR><_LF>
5.8.2*02(00000.1 kvarh)<_CR><_LF> 8.8.1*04()<_CR><_LF>
5.8.2*03(00000.1 kvarh)<_CR><_LF> 8.8.1*05()<_CR><_LF>
5.8.2*04()<_CR><_LF> 8.8.1*06()<_CR><_LF>
5.8.2*05()<_CR><_LF> 8.8.1*07()<_CR><_LF>
5.8.2*06()<_CR><_LF> 8.8.1*08()<_CR><_LF>
5.8.2*07()<_CR><_LF> 8.8.1*09()<_CR><_LF>
5.8.2*08()<_CR><_LF> 8.8.1*10()<_CR><_LF>
5.8.2*09()<_CR><_LF> 8.8.1*11()<_CR><_LF>
5.8.2*10()<_CR><_LF> 8.8.1*12()<_CR><_LF>
5.8.2*11()<_CR><_LF> 8.8.1*13()<_CR><_LF>
5.8.2*12()<_CR><_LF> 8.8.1*14()<_CR><_LF>
5.8.2*13()<_CR><_LF> 8.8.1*15()<_CR><_LF>
5.8.2*14()<_CR><_LF> 8.8.2(00000.1 kvarh)<_CR><_LF>
5.8.2*15()<_CR><_LF> 8.8.2*01(00000.1 kvarh)<_CR><_LF>
6.8.0*02(00000.0 kvarh)<_CR><_LF> 8.8.2*04()<_CR><_LF>
6.8.0*03(00000.0 kvarh)<_CR><_LF> 8.8.2*05()<_CR><_LF>
6.8.0*04()<_CR><_LF> 8.8.2*06()<_CR><_LF>
6.8.0*05()<_CR><_LF> 8.8.2*07()<_CR><_LF>
6.8.0*06()<_CR><_LF> 8.8.2*08()<_CR><_LF>
6.8.0*07()<_CR><_LF> 8.8.2*09()<_CR><_LF>
6.8.0*08()<_CR><_LF> 8.8.2*10()<_CR><_LF>
6.8.0*09()<_CR><_LF> 8.8.2*11()<_CR><_LF>
6.8.0*10()<_CR><_LF> 8.8.2*12()<_CR><_LF>
6.8.0*11()<_CR><_LF> 8.8.2*13()<_CR><_LF>
6.8.0*12()<_CR><_LF> 8.8.2*14()<_CR><_LF>
6.8.0*13()<_CR><_LF> 8.8.2*15()<_CR><_LF>
6.8.0*14()<_CR><_LF> 9.8.0(00007.6 kVAh)<_CR><_LF>
6.8.0*15()<_CR><_LF> 9.8.0*01(00007.4 kVAh)<_CR><_LF>
Comm_des_MT830 3 14.11.12
9.8.0*04()<_CR><_LF> 33.7.0(0.033)<_CR><_LF>
9.8.0*05()<_CR><_LF> 53.7.0(1.000)<_CR><_LF>
9.8.0*06()<_CR><_LF> 73.7.0(0.013)<_CR><_LF>
9.8.0*07()<_CR><_LF> 14.7.0(49.9 Hz)<_CR><_LF>
9.8.0*08()<_CR><_LF> 81.7.40(88.0 deg)<_CR><_LF>
9.8.0*09()<_CR><_LF> 81.7.51(0.0 deg)<_CR><_LF>
9.8.0*10()<_CR><_LF> 81.7.62(89.2 deg)<_CR><_LF>
9.8.0*11()<_CR><_LF> !<_CR><_LF>
9.8.0*12()<_CR><_LF> <ETX>b
9.8.0*14()<_CR><_LF>
9.8.0*15()<_CR><_LF>
9.8.1(00007.2 kVAh)<_CR><_LF>
9.8.1*01(00007.1 kVAh)<_CR><_LF>
9.8.1*02(00000.6 kVAh)<_CR><_LF>
9.8.1*03(00000.0 kVAh)<_CR><_LF>
9.8.1*04()<_CR><_LF>
9.8.1*05()<_CR><_LF>
9.8.1*06()<_CR><_LF>
9.8.1*07()<_CR><_LF>
9.8.1*08()<_CR><_LF>
9.8.1*09()<_CR><_LF>
9.8.1*10()<_CR><_LF>
9.8.1*11()<_CR><_LF>
9.8.1*12()<_CR><_LF>
9.8.1*13()<_CR><_LF>
9.8.1*14()<_CR><_LF>
9.8.1*15()<_CR><_LF>
9.8.2(00000.3 kVAh)<_CR><_LF>
9.8.2*01(00000.3 kVAh)<_CR><_LF>
9.8.2*02(00000.3 kVAh)<_CR><_LF>
9.8.2*03(00000.2 kVAh)<_CR><_LF>
9.8.2*04()<_CR><_LF>
9.8.2*05()<_CR><_LF>
9.8.2*06()<_CR><_LF>
9.8.2*07()<_CR><_LF>
9.8.2*08()<_CR><_LF>
9.8.2*09()<_CR><_LF>
9.8.2*10()<_CR><_LF>
9.8.2*11()<_CR><_LF>
9.8.2*12()<_CR><_LF>
9.8.2*13()<_CR><_LF>
9.8.2*14()<_CR><_LF>
9.8.2*15()<_CR><_LF>
10.8.0(00000.0 kVAh)<_CR><_LF>
10.8.0*01(00000.0 kVAh)<_CR><_LF>
10.8.0*02(00000.0 kVAh)<_CR><_LF>
10.8.0*03(00000.0 kVAh)<_CR><_LF>
10.8.0*04()<_CR><_LF>
10.8.0*05()<_CR><_LF>
10.8.0*06()<_CR><_LF>
10.8.0*07()<_CR><_LF>
10.8.0*08()<_CR><_LF>
10.8.0*09()<_CR><_LF>
10.8.0*10()<_CR><_LF>
10.8.0*11()<_CR><_LF>
10.8.0*12()<_CR><_LF>
10.8.0*13()<_CR><_LF>
10.8.0*14()<_CR><_LF>
10.8.0*15()<_CR><_LF>
31.7.0(7.9 A)<_CR><_LF>
51.7.0(2.4 A)<_CR><_LF>
71.7.0(5.8 A)<_CR><_LF>
32.7.0(58.1 V)<_CR><_LF>
52.7.0(58.6 V)<_CR><_LF>
72.7.0(58.2 V)<_CR><_LF>
Comm_des_MT830 4 14.11.12
Energy measurement
Technical Data specification

MT830/MT831 !
Three-phase electronic multi-function meter for industry
Technical Description
Version 1.4
Table of contents:
MT830/MT831 – Three-phase electronic multi-function meter .............................. 3
1. Meter characteristics ............................................................................................. 4
2. Constituent parts ................................................................................................... 5
2.1. Measuring system ............................................................................................. 6
2.2. Microcomputer ................................................................................................... 7
2.3. Real time clock .................................................................................................. 7
2.4. LEDs .................................................................................................................. 7
3. Multi-tariff registration ........................................................................................... 7
4. Maximum demand indicator ................................................................................. 8
5. Load Profile ............................................................................................................ 8
6. Registration of energy / power ............................................................................. 8
7. Display .................................................................................................................... 9
7.1. Keys................................................................................................................. 10
8. Communication interfaces .................................................................................. 10
8.1. IR communication interface ............................................................................. 10
8.1.1. Meter reading in absence of measuring voltages (option) ....................... 10
8.2. RS-485 interface ............................................................................................. 10
8.3. RS-232 interface ............................................................................................. 11
8.4. CS-communication interface ........................................................................... 11
9. Input /output module (MT831 meter only) ......................................................... 12
10. Communication module (MT831 meter only) .................................................. 14
11. Fraud protection ................................................................................................ 15
11.1. Detection of meter cover and terminal cover opening .................................. 15
12. Handling with the meter .................................................................................... 16
13. Connection procedure....................................................................................... 16
14. Housing ............................................................................................................... 17
15. Terminal block .................................................................................................... 20
15.1. Terminal block ............................................................................................... 20
15.2. Current terminals ........................................................................................... 20
15.3. Auxiliary voltage terminals: ........................................................................... 20
15.4. Sliding voltage bridge .................................................................................... 20
15.5. Dimensions .................................................................................................... 21
16. Maintenance: ...................................................................................................... 22
17. Lifetime: .............................................................................................................. 22
18. Technical data .................................................................................................... 22
19. Type designation ............................................................................................... 25
19.1. Meter marking ............................................................................................... 25
20. Input-output module marking (for MT831 meter only) ................................... 26
21. Communication module marking (for MT831 meters only) ........................... 27
22. Configuring a PC modem .................................................................................. 30
Appendix A: OBIS codes and data names ............................................................ 36
Appendix B: Log book events ................................................................................ 43
Appendix C: Connection diagrams ........................................................................ 45
MT830/MT831 ─ Three-phase electronic multi-function meter
MT830/MT831 – Three-phase electronic multi-function meter

MT830/MT831 three-phase electronic multi-function meter is intended for measuring active and apparent energy in
two flow directions, reactive energy in four quadrants as well as imported and exported, maximal power of the above
stated energies, registration of load curves and quality parameters of supplied electric energy in three-phase three-
and four-wire networks. The meters can be connected directly, semi-directly or indirectly. They comply with the IEC
62052–11, IEC 62053-21, EN 50470-3, IEC 62053-22 and IEC 62053-23 standards, VDEW demands, and they are
manufactured in compliance with the ISO 9001 standard. The meter consists of a polycarbonate housing, electronics
for measuring and processing measuring data, input/output as well as communication electronics.
Two different meter versions are available:

 MT830 - a “closed” meter version with additional six terminals, which could be used for:
o Communication interface
o Functional or impulse inputs
o Functional outputs
o External power suplly
Figure 1: MT830 – a “closed” meter version
 MT831 – a modular meter version with communication (MK) and input/output (MIO) module which could be
subsequently built into the meter and six additional terminals
Figure 2: MT831 – a modular meter version
3
1. Meter characteristics
 Measuring active energy/power

 Measuring reactive energy/power in four quadrants and/or a sum of energies by individual quadrants (e.g.
Q1+Q2 and Q3+Q4)
 Measuring apparent energy/power
 Calculating cumulative power
 Measuring and displaying parameters of energy quality:
 rms voltage values by phases
 Current by phases
th
 Harmonic components in voltage and current (up to the 8 harmonic)
 Power factor per phase and total
 Phase angle between phase voltage and current
 Voltage failures
 Multi-tariff registration
 Load profiles (P.01, P.02)
 Log-books (P.98, P.99)
 Different display modes on LCD
 Meter reading in case of power down (“no power reading option with SONDA 6 (option)
 VDEW designed LCD  presence of phase voltages, energy flow direction, units and 11 statuses
 Communications
IR interface for a local readout and meter programming (IEC 62056-21)
 Auxiliary terminals
The main meter board (MT830 & MT831) could be equipped with up to six auxiliary terminals, which could be:
o Communication on board port (MT830 only)
MT830 meter could be equipped with
 CS interface
or
 RS-485 interface
or
 RS-232 interface
Communication with the meter is performed in compliance with the IEC 62056-21 standard, mode C. The meter
operation is not affected during communication.
Type of communication:
Serial asynchronous half-duplex ISO 1177
1 start bit
7 data bits
1 bit parity - even
1 stop bit
data transfer rate: 300, 600, 1200, 2400, 4800, 9600 Baud
Each communication port supports “fix” baud rate (for use of transparent telephone modems) or communication protocol
according to IEC 62056-21 standard (communication sequence is started with 300 baud). Communication parameters in
the meter are programmable.
The meter enables separate read out (different data) via IR and other communication interface at the same time.
The MT831 meter could be equipped with different communication modules (MK).
 Two inputs (3 terminals) are used
 Functional or
 Impulse inputs
4
Control voltage is from 100 V….240 V AC/DC.

Additional inputs & outputs could be implemented in input/output module (I/O module) – the MT831 meter only.
Electrical characteristics:
 OFF state <= 30 V
 ON state >= 45 V
 Internal resistance 190 KOhm
 Switch on delay  typical 10 ms at 240V
 Four outputs in two functional groups (6 terminals)
 External power supply (2 terminals)
Terminal Additional
Terminal
designation explanation
50 – 240 V
30 External power supply
AC/DC
50 – 240 V
31 External power supply
AC/DC
 Modular construction – the MT831 meter only

MT831 could be upgraded with input/output (MIO) and communication (MK) module.
 Fraud detection
 Detection of a meter cover and a terminal cover opening
 Connection to network: a three-phase meter can also be used as a single-phase or two-phase type
 Quality:
 High accuracy as well as time stability of measurement
 High reliability of operation and long life span (20 years)
 High immunity to EMC disturbances
 Simple and fast assembly
 A compact plastic housing is made of high quality self-extinguishable materials and is resistant to water and dust
(IP53)
 Environment friendly: a meter is made of the materials that can be recycled or are not dangerous for the
environment
2. Constituent parts
The meter consists of the following units:
 Measuring systems
 Microcontroller with external memory
 Real time clock
 LCD
 Optical interface
 Keys
 LEDs
 Power supply :
o Internal three phase switcher
o external power supply
o power supply via optical probe (“no power” reading option with SONDA 6 )
5
Figure 3 – A meter block diagram
2.1. Measuring system

The measuring systems are based on Rogowski coils that measure changes on the induced voltage. Current flows
through a current coil. Voltage is induced inside the air coils due to alternate magnetic field. There are two Rogowski
coils on each phase.
The measuring system is made of:

1. Current coil frame
2. Current coil
3. Two Rogowski coils
4. PCB
Figure 4 – Measuring system
A measuring system measures induced voltage on measuring coils which is proportional to the current on input. The
first coil measures “load” energy and the second one is a compensation coil which measures outside disturbances.
Compensation value is subtracted from a measuring element.
An output signal from Rogowsky coils is related to the input of the measuring integrated current. A signal is integrated,
amplified and multiplied with measuring voltage and sent to the microprocessor.
Figure 5 – Measuring principle
Sensors and circuits are protected from overvoltage. Influences of disturbance quantities are negligible, which assures
high meter reliability.
6
2.2. Microcomputer
A microcomputer enables:
 Meter functions by customer's specification
 Storing measuring data and parameters
 Storing measuring data for previous billing periods (factory settings is 15 billing periods)
 Demand calculations
 Load Profile function
 Compensating measuring protocol of voltage and current transformers
 Logbook
 Display control
 Certain supervision and control meter functions for measuring phase voltages
 Measuring phase voltages
 Measuring harmonic components in current and voltage
 Measuring frequency
Operation of the microcomputer is controlled by a special Watch-dog circuit.
2.3. Real time clock

A real time clock is controlled by a 32 kHz quartz oscillator. The clock accuracy complies with the IEC 61038 standard
requirements. Back up power supply source is built in the meter . It is usually a supercapactior and an Li battery which
is directly soldered to the main printed circuit board. The supercapacitor assures energy for 250 hours of the clock
operation in case of a complete power supply failure, while an Li battery assures 10 years of operation, with time life
span of 20 years.
A real time clock generates:
 A measuring period for power and a registration period for load profile
 Tariff programs, season changeover, transition to day light saving period and vice-versa
 Time stamps of individual events. A time-stamp consists of a date, an hour, a minute and a second of the event.
2.4. LEDs
Two LEDs are built in the meter:
 Left  active (imp/kWh)
 Right  reactive (imp/kvarh) or apparent (imp/kVAh) (programmable)
They enable meter calibration. Impulse constants depend on nominal current and voltage and are programmable
values.
Factory settings:
 Direct connected meter
o 3x230/400 V, 5(60) A  1.000 imp/kWh
o 3x230/400 V, 5(120) A  500 imp/kWh
 Transformer connected meter

o 3x57.7/100 …. 3x240/415V, 5(6)A  10.000 imp/kWh
To reduce the control time a special factory test mode is built in the meter, which increases LED constants 10 times
higher, in comparison with a normal operating mode. After power down/up event, all constants take the original
factory settings.
3. Multi-tariff registration
The meter enables registration of energy and power by separate tariff schemes. Up to 8 tariffs for energy and demand
could be registered (factory settings  4 tariffs). The meter is equipped with 160 tariff registers. Time of switching
individual tariff is defined by hour and minute with a resolution of 1 minute. A number of periods in a day where one or
several tariffs can be valid is defined with configuration. The same is valid for different daily tariff programs. Up to 32
various types of a day (a day in a week and a holiday) can be defined. A number of seasons in a year (factory settings
 4 seasons) is defined with configuration. Besides a current tariff program, the so-called slipping tariff programs can
be defined. They are activated at previously defined dates. An optional number of holidays can be defined. A century-
old callendar is built in the meter.
7
4. Maximum demand indicator

Maximum demand can be measured with a fixed or a sliding measuring period. A measuring period can be set from 1
minute to 60 minutes with a 1-minute resolution. It is possible to measure maximum demands for:
 Active energy in both flow directions
 Reactive energy in four quadrants as well as a sum of energies by individual quadrants (e.g. Q1+Q2 and
Q3+Q4)
 Apparent energy in both energy-flow directions
Maximum demands are registered by individual tariffs and cummulatively.

Configuration of blocking the measurement of maximum demand for a certain time that follows a period of network
voltage failure is also available.
5. Load Profile
A programmable data recorder enabling registration of a load profile is built in the meter:
 Active, apparent power and energy (cumulative or absolute values)  three-phase values in both energy flow
directions
 Reactive power or energy (cumulative or absolute values) in four or combined quadrants (e.g. Q1+Q2 and
Q3+Q4)
 Rms values of phase voltages
 Distortion factor
 Individual meter statuses (power supply failure, alarms)
A registration period or a load profile can be set within the range from 1 to 60 minutes. Two load profiles (P.01 and
P.02) could be implemented in the meter. The first one (P.01) is normaly used for registering energy or demand, and the
second one for registering the last average of voltage, current and power factor. Last average registration is related to
the measuring period. Load profile periods and measurment period are independend from each other.
6. Registration of energy / power

The MT830/MT831 meter has three measuring systems and could be used in a three-phase three-wire or three-phase
four-wire networks.
Registration types:
 Vector registration ( Li),
 when the vector sum of energies is positive, the meter registers A+ energy;  when the vector sum of energies
is negative, the meter registers A- energy
For example (phase load is the same)

Phase: L1 L2 L3
Load: +A -A +A
Total registration (1.8.0)  (+A) + (-A) + (+A) = +A

Total registration (2.8.0)  0
Meter registers +A (one phase load!!).
 Arithmetical registration  the meter could register A+ and A- energy in the same time

Phase: L1 L2 L3
Load: +A -A +A
Total registration
Positive direction (1.8.0)  (+A) + (+A) = 2*(+A)
Negative direction (2.8.0)  -A
If the second phase is wrongly connected, the meter also registers this energy with such registration type.
 Absolute active energy A 
8
Phase: L1 L2 L3
Load: +A -A +A
Total registration
Positive direction (1.8.0) +A+-A++A=3*(+A)
With such registration the meter registers only “imported” energy, also in case of “wrong” connection.
For measuring reactive energy a natural connection is used. Internal register provides for a corresponding voltage and
current phase shift.
MT830/MT831 meters could be provided with:
 three measuring systems (MT830 – T1 /MT831 – T1) – transformer connected
7. Display
LCD is designed according to the VDEW requirements.
Figure 6 - LCD
The measuring data on LCD are displayed with eight 7-segment 8 mm x 4 mm high numbers. Displayed data are
identified with five-digit OBIS identification codes (IEC 62056 – 61), 6 mm x 3 mm high numbers. Dimension of LCD
(visible area) is 69 mm x 20 mm.
Meters have back-light illumination for easy data reading at metering place with bad light condition. The LCD is
illuminated when any pushbutton is pressed. The illumination is switched-off after 3 minutes if no pushbutton was
pressed at that time.
A meter operates in different display modes
 Automatic data circulation  Autoscrool

(Time between two register presentations in LCD is programmable). Because only 5 digits are used for
identification, 9 previous register values are presented on the LCD.
Additional modes are accessible with a black and a red button.

Displaying modes accessible with the black one:
 Manual data display – registers  Std dAtA

 Manual data display – network parameters (voltage, current, phase angle, etc.)  Grid
 Manual data display– Load Profile (P.01 and/or P.02 (programmable))
 Presentation of the GSM modem parameters  DiAg (C.C.3  signal level (should be higher than 17), C.C.4
 GSM provider (1 – home provider, 5 – roaming), C.C.5  error code (should be 0))
Displaying modes accessible with the red button:

 Manual setting of time, date, etc.  SET mode
 Registers presented in Autoscool mode with enhanced energy registers presentation  TEST mode
 Resetting the LCD statuses of meter and terminal cover opening  Intrusion restart mode
Format and data units are programmed. At transformer connected meters, displayed measuring data can be primary, or
secondary.
Besides measuring data, the energy flow direction, presence of phase voltages, display of individual events, meter
statuses and alarms can be displayed.
9
7.1. Keys
The meter is equipped with three keys.
Black  dislay key is used for transition from a basic to an extended data display mode.
Red  reset key is used for billing meter reset or, in combination with the DISPLAY key, for setting certain meter
parameters (SET, TEST or Intrusion restart meter operation mode). The RESET key is sealed separately or it can be
locked.
Param key is under the meter cover and is used for setting meter parameters in the laboratory.
8. Communication interfaces
An optical communication interface is located on the meter basic board. One of communication interfaces that are
intended for remote meter readout (CS or RS-232 or RS-485) can be mounted on customer demand. The meter is
provided with two independent communication channels.
8.1. IR communication interface

The optical communication interface enables a user to set the meter parameters and read the measuring results
(registers reading, a logbook, a load profile, reading individual registers, sending individual commands).
8.1.1. Meter reading in absence of measuring voltages (option)
On customer’s request, the meter can be equipped with additional electronics, which enables communication via an
optical interface also in case of measuring voltages failure. This is enabled with a special probe (SONDA 6). It is also
possible to read meter data manually by means of the DISPLAY key.
Figure 7 – “No power” meter reading option with SONDA 6 (option for MT830/MT831)
8.2. RS-485 interface

The RS-485 serial interface enables communication with maximum transmission rate 9600 bauds. The MT830 meters
with a built-in RS 485 interface are equipped with two auxiliary terminals. Up to 31 meters can be connected to the
RS-485 interface with maximum distance of 1200 m. In such configuration, the meter readout is obligatory with device
10
address! For longer distances (more than few hundred meters), the use of termination resistor of 120 Ohm on each
edge is recommended.
Terminal Additional
Terminal
27 A A terminal
29 B B terminal
Table1 – RS-485 terminals designation
Figure 8 – Meters connected to the modem via RS-485 interface
8.3. RS-232 interface
The RS 232 serial interface enables communication with maximum transmission rate 9600 bauds. The MT830 meters
with built-in RS 232 interface are equipped with three auxiliary terminals
Terminal Additional
Terminal
27 RxD Rx terminal
28 GND Common terminal
29 TxD Tx terminal
Table 2 – RS-232 terminals designation
or RJ11 connector.
Figure 9 – RS-232 RJ11 terminal designation
8.4. CS-communication interface

The CS interface (20-mA current loop) complies with the DIN 66348 standard and is two-wire communication. It
enables communication with maximum transmission rate 9600 bauds. The MT830 meters with built-in CS interface
are equipped with two auxiliary terminals. Up to four meters can be connected to the CS interface with maximum
distance of 1500m. In such configuration, the meter readout is obligatory with a device address!
11
Terminal Additional
Terminal
23 CS+ CS+ terminal
24 CS- CS- terminal
Table 3 – CS interface terminals designation
Figure 10 – Meters connected to the modem via CS interface
.
9. Input /output module (MT831 meter only)
I/O modules are plug & play. Two versions regarding the internal programming are available:
 Input – output module function is predefined in module EEROM

The module is pre-programmed in the factory. After inserting the module into the meter, the meter automatically
accepts the module parameters (plug and play module). Terminals are marked according to the VDEW
requirements. The module can be re- programmed only in the factory
 Input – output module function is not predefined in module EEROM

The function of input-output module terminals is defined when setting meter parameters which are specified in the
group “Input/output pins”  MeterView 4 program. Terminal designations:
- Cx for common terminals
- Tx for output terminals
- TEx for input terminals
where x is from 1 to n (a terminal number).
Standard versions are:

- MIO-V12L51  4 outputs + 1 output + 1 input
- MIO-V42L81  4 outputs + 4 outputs + 4 inputs
- MIO-V12L41B11  4 outputs + 1 output 5A bistable rele + 1 input
Error on an input/output module does not influence in the meter operation.
Figure 11 - Input/output module (MT831 only)
12
Definition of input terminals:

Terminal Additional
Terminal
Common terminal for
15 COM
functional inputs
TE1/2, Energy tariff input T1 –
13, 33
TE3/4 T4
ME1/2, Demand tariff input M1
14, 34
ME3/4 – M4
External
time/measurement
16 MPE
period synchronization
input
External input for
17 MZE disabling of demand
measurement
Input a for external
18 MREa
billing reset
Input b for external
19 MREb
billing reset
21 MKE1 Alarm input 1
22 MKE2 Alarm input 2
Common terminal for
90 COM
impulse inputs
91 IME1 Impulse input 1
92 IME2 Impulse input 2
Table 4 – Input terminals designation
Impulse inputs are realized as passive inputs. An impulse constant is programmable and could be different for each
impulse input. Maximum impulse frequency is 25 imp/sec.
Definition of output terminals:

Terminal Additional
Terminal
35 COM Common terminal
36 MKA Alarm output
Measurement period
37 MPA
output
Energy flow direction
38 ERA+A
+A
Energy flow direction
39 ERA+R
+R
41 +AA Pulse output for +A
42 -AA Pulse output for -A
43 +RA Pulse output for +R
44 -RA Pulse output for -R
45 RA1 Pulse output for RA1
13
Common terminal for

52 COM
41 and 42 terminals
Common terminal for
54 COM
43 and 44 terminals
Common terminal for
56 COM
45 and 46 terminals
Common terminal for
58 COM
47 and 48 terminals
Common terminal for
59 COM terminals from 45 up to
48
TA1/2, Demand tariff outputs
61, 63
TA3/4 T1 – T4
MA1/2, Demand tariff outputs
62, 64
MA3/4 M1 – M4
Output for external
68 MRAa
billing reset a
Output for external
69 MRAb
billing reset b
71 LA1 Load control output 1
72 LA2 Load control output 2
Table 6 – Output terminals designation
10. Communication module (MT831 meter only)

Communication modules are plug & play. Two versions regarding the internal programming available:
 Communication module parameters setting is predefined in the module EEROM
The module is pre-programmed in the factory (baud rate, parity, stop bit, some special modem settings). After
inserting the module in the meter, the meter automatically accepts the module parameters (a plug and play
module).
 Communication module parameters setting is not predefined in the module EEROM

All settings regarding the communication modem accept from the meter parameters. The modem is automatically
initialized after predefined period or meters internal initializations.
Each module, except the RS-232 module with a 25-pin DB connector, has two independent communication interfaces,
which enables simultaneous meter reading. Communication interfaces are isolated from each other.
Additional special programming (for example: PSTN modem) is possible with the MeterView 4 program.
Communication module designation:

st nd
MK – the 1 comm. Inter. – the 2 comm. Inter.
For example:
MK – f38 – 3
First communication interface (MK – f38 – 3):
8  GSM modem
+
14
3  RS-485 interface
+
f  active CS interface
(it is possible to establish multi drop communication via RS-485 and CS communication interface)
Second communication interface (MK – f38 – 3):

3  RS-485
Second (independent) RS-485 communication interface.
Besides communication towards the centre, the modules also offer possibility of cascade connection (a CS interface
and an RS-485 interface). The module enables hot swap installation (modules can be changed or built into the meter
during the meter operation). The modules are located under the terminal cover and are not sealed with a metrological
seal. On costumer’s request, modules could be sealed with an unremovable sticker.
The same communication module can be built into different meter types: MT831 and MT860. All modules are »plug &
play« type. When the module is built in, it sends its identification code via a data bus. The module is automatically
recognized by the meter and is correspondingly controlled.
The error on the communication module does not influence in the meter operation.
Figure 12 - Communication module (MT831 only)
11. Fraud protection

The meter is protected against fraud in several ways.
 The meter cover and the terminal cover are sealed separately
 The RESET key is sealed or locked with a lock
 Commands and accesses to individual registers are protected with three password levels
 All interventions into the meter are recorded in a logbook
 Measuring data are stored in a nonvolatile memory on two places (a primary and a secondary copy)
11.1. Detection of meter cover and terminal cover opening
MT830/MT831 meter detects the meter cover (MCO) and terminal cover (TCO) opening. Time and date of such
occurrence are written in the meter logbook. The state of the MCO and TCO opening could also be presented in the
status flags on the LCD.
When the meter is powered via measuring voltages or auxiliary power supply, the opening time stamp present the real
(actual) time.
Example:
(a terminal and a meter cover were opened during “normal” meter operation  meter was powered by measuring
voltages)
(060317115820)(0080)  power down
(060317125820)(0040)  power up
15
(060317132820)(0020)  time setting
(060317134520)(0020)  time setting
(060317135940)(811B)  terminal cover opened
(060317140015)(811D)  meter cover opened
The meter also detects the TCO and MCO in case of power down but without the real time of such event. Meter
electronics detects only opening event, while date and time in such case are related to the first power up.
Example:
A terminal and a meter cover were opened during power down.
(060317115820)(0080)  power down
 meter and terminal cover were opened during this time
(060317145820)(0040)  power up
(060317145821)(811B)  terminal cover opened
(060317145821)(811D)  meter cover opened
After installing the meter, at least MCO event is registered in the meter Log Book or in the status flag on the LCD. To
restart the TCO and MCO registering “Intrusion Restart” function must be implemented. This function is accessible by
using the black and the red button or remotely by sending a special command into the meter. Intrusion Restart function
is automatically done after power up event, parameter changing (when meter goes through the “Standby”).
After “Intrusion Restart”, the meter detects only one TCO and MCO opening.
Note: to detect the opening of the meter and the terminal cover, “Intrusion Restart” must be implemented!
12. Handling with the meter

Two sets of tools are available:
 For service programming and readout:
 MeterView 4 (Iskraemeco software)
 An optical probe
 A PC, a table or a portable one (PC - desk-top, PC – laptop).
The tool is intended for the operators who service or reprogramme the meters in the laboratory or in the field.
 For billing readout and programming:

 MeterRead (Iskraemeco software), for all types of palmtop PCs operating in the WinCE environment
 An optical probe
The tool is intended for readers in the field.
13. Connection procedure

1. Meter assembly
2. Meter connection to network
3. Checking connection indication – a LED is lit
4. Checking correct connection – see LCD indications:
 Presence of all three phases - L1 L2 L3 all symbols are displayed
 At least 1 phase is absent - L1 L3 absent phase is marked
 Wrong phase sequence - L1 L2 L3 symbols of wrongly connected phases are blinking
16
14. Housing
The meter housing is made of self-extinguishable polycarbonate that can be recycled. The housing assures double
isolation and IP53 protection degree against dust and water penetration. Meter dimensions and fixing dimensions
comply with the DIN 43857 standard. A hook fixing is adapted by height. In case of a simple version, the mask does not
have any bed for modules and the meter cover is extended
Figure 13 - A hook adjustable by height (MT830/MT831)
17
1. LCD
14 2. Meter technical data
1
3. IR optical interface
4. Input/output module mark
5. Legend of displaying registers on
2 LCD
13
6. Meter cover sealing screw
12 7. Terminal cover
10 8. Terminal cover sealing screw
3 9. Communication module mark
4 9 10. RESET key blocking element
11. RESET key
5 12. DISPLAY key
13. Impulse diode – active and
reactive energy
6 14. Meter cover
7
Switch for detecting terminal cover
opening
Figure 14 - Meter constituent parts
Connect. Addition. Neutral Auxiliary

current voltage terminal terminals
terminals terminals
18
Meter cover
sealing screw
Position 0
Position 1
Sliding voltage bridge Auxil. Terminal

terminals cover
sealing
screw
Figure 15 - Terminal block constituent parts for direct connected meter
19
15. Terminal block

15.1. Terminal block
A terminal block complies with the standard. It is made of high quality polycarbonate that assures: resistance to
high temperatures, voltage breakdown and mechanical strength.
15.2. Current terminals

Direct connected meter:
Connection terminals are made of nickel plated steels and have only one screw per terminal. A universal
clamping terminal assures the same quality of the contact irrespective of the shape of the connection conductor
(a compact wire, a stranded wire, greater or smaller cross-section). It is made of brass and has only one screw.
It also assures faster meter assembly.
Figure 16: Current terminals for direct connected meter version
15.3. Auxiliary voltage terminals:

A direct connected meter:
The meter can be equipped with max. four auxiliary voltage terminals (L1, L2, L3, N). They enable simple
connection of additional external devices.
15.4. Sliding voltage bridge

Direct connected meter:
Sliding voltage bridges are intended for fast and simple separation of a meter current and voltage circuit used
for calibration or accuracy testing. In each phase of the connection terminal a special plastic slider is built in. It
can be shifted up and down with a screwdriver. When a voltage bridge is in »0« position, it means that the
voltage part is separated from the current part, while in position »1« it is closed.
Figure 17: Sliding voltage bridge
Position 0: Voltage bridge is disconnected

Position 1: Voltage bridge is connected
Different versions of sliding bridges exist:

 External connection
Figure 18: External version of voltage bridges
 Internal connection (voltages bridges are accessible only by opening the meter cover)
20
Figure 19: Internal version of voltage bridges
 Cop5 terminal (voltage terminals are covered) – also for transformer connected meter
Figure 20: Meter terminals are covered with special Cop5 cover
15.5. Dimensions
Meter fixing dimensions comply with the DIN 43857 standard.
Figure 21- Meter fixing dimensions (MT830)
21
Figure 22- Meter fixing dimensions (MT831)
16. Maintenance:
The meter is designed and manufactured in such a way that it does not need any maintenance interventions in the
entire lifetime. Measuring stability assures that no recalibration is required. The meter with the internal battery assures
sufficient capacity for performing battery-supported functions for the entire lifetime
17. Lifetime:
The meter is designed for 20-year lifetime at normal operating conditions.
18. Technical data

Accuracy class
Active energy A or B or C (EN 50470 - 3)
Class 2 or 1 (IEC 62053-21)

Class 0.5S (IEC 62053-22)
Reactive energy Classes 2, 3 (IEC 62053-23), calibrated up to 1%
Apparent energy Class 2 or 3, calibrated up to 1%

Voltages (V)
Voltage range 3 x 57.7/100V ... 3 x 240/415V
3x100V … 3x415V (3P3W - external Aaron connection)
3x100V … 3x230V (3P3W connection)
0.8 - 1.15 Un
Reference frequency 50 Hz ±5 % or 60Hz ±5 %
22
Currents (A)
Direct connection 0.25 – 5(120)A, (Class A or B)
Indirect connection 0.01 – 1(6)A, (Class A or B or C)

0.01 – 1(10)A, (Class A or B or C)
0.05 – 5(6)A, (Class A or B or C)
0.01 – 5(10)A, (Class A or B or C)
0.05 – 5(20)A, (Class A or B or C)
Start up current 0.002In for class A or B (EN 50470 - 3)

0.002In for class 2 or 1 (EN 62053 - 21)
0.001In for class C (EN 50470 - 3)

0.001In for class 0.5S (EN 62053 - 21)
Short-circuit 30 Imax for direct connected

20 Imax for indirect connected
Outputs
Type PHOTO-MOS voltage-free relay
Contact Make or break contact
Permitted load 25 VA (100 mA, 275 V AC)
Pulse length From 20 ms to 240 ms (adjustable in steps by 20 ms)
Transmission distance Up to 1 km
Inputs
Voltage level 100 – 240 V AC
ON: U  80 V
OFF: U  20 V
Current consumption < 2 mA @ 50V

< 10 mA @ 240V
Self consumption of < 0,1 VA / phase
current circuit
Self consumption of 0.5 W / 1.1 VA (self consumption of voltage circuits, when meter is
voltage circuits supplied from the measuring voltages)
0.2 W / 0.4 VA (self consumption of voltage circuits, when meter is

supplied from the external voltage)
1.1 W / 3.7 VA (self consumption of the external power supply, when

meter is supplied from the external voltage)
max. 2.5 W / 3 VA (GSM module)

Communication
IR Max. 9600 Baud IEC62056-21
CS Max. 9600 Baud, passive, CL0 in compliance with DIN 66348, Part 1.
RS232 Max. 9600 Baud
RS485 Max. 9600 Baud
Protocols 62056-21 mode C with or without a password.

LED output Impulse frequency  40 Hz
Impulse length approx. 8 ms
23
Real time clock

Accuracy Crystal: 6 ppm =  3 min./year (at Top= +25C)
Back-up power supply Super-Cap: 0.1F and Li-battery

External power supply 50 - 240 V AC/DC
EMC
Electrostatic discharge 15 kV (IEC 60801-2)
VF magnetic field 10 V/m (IEC 60801-3)
Transient test 4 kV (IEC 60801-4)
Insulation strength 4 kVrms, 50 Hz, 1 min
Impulse voltage 6 kV, 1.2/50 s
Glow wire test IEC 695-2-1
Spring hammer test IEC 60068-2-75

Temperature ranges
Operation -40C ... +70C
Storing -40C ... +80C

Humidity > 95%
Terminals (diameter) CT connection: 5 mm (2 screws per terminal)
Direct connection: 9.5 mm (one screw per terminal)

Dimensions 327 x 177 x 90 mm
Mass Approx. 1.4 kg
Table 7 Technical data
24
19. Type designation
19.1. Meter marking
M T 83x – D2 (T1) AnmRnmSnm – EnVn2Lnm – M3 K0xZ4
MT83x three-phase multi-function four-quadrant electronic meter with three

measuring systems
0 closed (basis) version of the meter
1 modular version of the meter
D2 a meter for direct connection and max. current 120 A
T1 transformer rated meter and max. current 20 A
A Active energy
n=3 class 0.5S, C (IEC 62053-22, EN 50470-3)
n=4 class 1, B (IEC 62053-21, EN 50470-3)
n=5 class 2, A (IEC 62053-21, EN 50470-3)
m=1 one energy flow direction
m=2 two energy flow directions
R Reactive energy
n=4 class 2 (IEC 62053 – 23), calibrated to 1%
n=5 class 2 (IEC 62053 – 23)
n=6 class 3 (IEC 62053 – 23)
m=1 reactive energy flow in one direction (Q+ = Q1 + Q2)
m=2 reactive energy flow in two directions (Q+ = Q1 + Q2 and
Q-=Q3 + Q4)
m=3 inductive reactive energy - reception, capacitive reactive energy
transmission (Q1 and Q4)
m=4 inductive reactive energy in two directions (Q1 in Q3)
m=5 measurement of reactive energy in four quadrants (Q1, Q2, Q3 and Q4)
m=6 measurement of reactive energy in four quadrants, reception and
transmission (Q1, Q2, Q3, Q4 Q+ and Q-)
S Apparent energy
n=4 adjusted to 1%
n=5 adjusted to 2%
n=6 adjusted to 3%
2+ 2
m=3 apparent energy  P Q
E External power supply
n=1 power supply of the whole meter
n=2 power supply via the optical probe (reading if measuring voltages are
absent)
V Control inputs
n = 1..2 a number of inputs
2 control voltage is phase voltage
L OptoMOS relay outputs
n=1..4 a number of outputs
m=1 make contact
m=2 optoMOS relay
M Additional device
3 real time clock + Li battery
K Communication interface
0 first interface: IR – optical interface
1 second interface: CS-interface (20 mA current loop) (MT830 only)
2 second interface: RS-232 (MT830 only)
3 second interface: RS-485 (MT830 only)
Z Load profile recorder
4 memory capacity for load profile 512k FLASH
ROM
25
20. Input-output module marking (for MT831 meter only)
MIO - Vn2 Ln1 B11
MIO Input output module

V Control inputs
n = 1..4 a number of inputs
2 control voltage is phase voltage
L OptoMOS relay outputs
n = 1..8 a number of outputs
1 make contact
B Relay outputs
n=1 5A bistable relay
Input/output module options:
MIO – V12L51
MIO – V42L81
MIO – V12L41B11
Input/output module MIO – V12L51
Module marking:
Connection diagram
Input/output module
terminals
26
Example of factory preprogrammed module (function of the terminals are defined in the module) :
Common G 15
External synchronization (for
Active MPE 16
clock/demand period)
Common G 35
Measuring period make contact MPA 37
Common G 40
Pulse output for active energy +A make contact +AA 41
Pulse output for active energy -A make contact +AA 42
Pulse output for reactive energy +R make contact +RA 43
Pulse output for reactive energy -R make contact -AA 44
21. Communication module marking (for MT831 meters only)
MK – f3n - m
MK Communication module
f active CS- interface (20 mA current loop) – for multidrop communication
1 passive CS- interface (20 mA current loop)
2 RS-232 interface
3 RS-485 interface–for multidrop communication (module with modem)
n = 7..9,a,e the first communication interface (type of modem)
n=7 PSTN modem
n=8 GSM modem
n=9 ISDN modem
n=a GSM/GPRS modem
n=e Ethernet
m the second communication interface
m=1 passive CS - interface (20 mA current loop)
m=2 RS-232 interface
m=3 RS-485 interface
Communication module options:
MK – 2 – 3 (RS-232 & RS-485 interface)

MK – 1 – 3 (CS interface & RS-485 interface)
MK – 3 – 3 (RS-485 interface & RS-485 interface)
MK – f37 – 3 (PSTN modem+CS+RS-485 interface & RS-485 interface)  module enables multidrop communication
MK – f38 – 3 (GSM modem+CS+RS-485 interface & RS-485 interface)  module enables multidrop
communication
MK – f39 – 3 (ISDN modem+CS+RS-485 interface & RS-485 interface)  module enables multidrop communication
27
MK – f38a – 3 (GSM/GPRS modem+CS+RS-485 interface & RS-485 interface)  module enables multidrop
communication
MK – 3e – 3 (Ethernet+RS-485 & RS-485 interface)  module enables multidrop communication
MK-MB-3-e-3 (MODBUS; Etherne interface+ RS-485 & RS-485 interface)  module enables multidrop
communication
GSM/GPRS communication module MK – f3a – 3
Module marking:
Connection diagram
Installation of the SIM card (SIM card must be enabled for data transfer)
1. Remove the GSM/GPRS modem from the meter
28
2. SIM card must be without PIN code

3. Insert the SIM card into the SIM cardholder
Move lock to the left,

to enable opening
the SIM cardholder!
4. Insert the GSM modem back into the meter
5. Connect the antenna with the modem
6. With the DIAG menu on the meter (accessible with the black button), the following can be checked:
 C.C.3  a signal level (should be higher than 17)
 C.C.4  GSM provider (1 – home provider, 5 – roaming)
29
 C.C.5  error code (should be 0)
22. Configuring a PC modem

What is described below is the general method of installing a modem. You should follow the instructions given by your
modem's manufacturer if different from any information given here.
The most effective way to use a modem with Meter View is to properly install it in Windows. To do this, launch Windows
Control Panel (click the Windows Start button, click Settings if you see this option, then click Control Panel) and start the
Phone and Modem Settings applet.
Click the Modems tab and you should see the following window.
The Windows Control Panel Phone and Modem Options window.

The contents of the list of modems will depend on your system current configuration.
To add a modem, click Add... to see the Windows Add Hardware Wizard and follow the on-screen instructions.
If your modem is connected to your computer, it is a good idea to do a diagnostic check when you return to the
Windows Phone and Modem Options window. To do this, select the newly added device and click Properties. Click the
Diagnostics tab in the window and a window that closely resembles the following is displayed. The specific details of the
displayed window depend on the modem make and model.
30
Windows Modem Properties window

Click the Query Modem button to see that the Command and Response list is populated and that no error messages
are displayed.
If your modem requires additional commands to select the correct mode of operation, click the Advanced tab to see the
following window.
Consult your modem documentation on the commands available to you.
Communication with the MT8xx meters is performed in compliance with the IEC 1107 standard with Mode C protocol.
Type of communication: Serial asynchronous half-duplex ISO 1177

1 start bit
7 data bits
1 bit parity - even
1 stop bit
Data transfer rate: 300, 600, 1200, 2400, 4800, 9600 Baud
Appropriate modem settings:
31
32
33
Check also FIFO buffer settings (especially for XP windows):
Advanced 
34
or
35
Appendix A: OBIS codes and data names
OBIS code Data name

Three phases energy registers, t = TOU registers (1,..n)
1-0:1.8.0 A+, Active energy import, total register
1-0:1.8.t A+, Active energy import, TOU register
1-0:1.9.0 A+, Active energy import in the billing period, total register
1-0:1.9.t A+, Active energy import in the billing period, TOU register
1-0:2.8.0 A-, Active energy export, total register
1-0:2.8.t A-, Active energy export, TOU register
1-0:2.9.0 A-, Active energy export in the billing period, total register
1-0:2.9.t A-, Active energy export in the billing period, TOU register
1-0:3.8.0 Q+=Q1+ Q2, Reactive energy import, total register
1-0:3.8.t Q+=Q1+ Q2, Reactive energy import, TOU register
1-0:3.9.0 Q+=Q1+ Q2, Reactive energy import in the billing period, total register
1-0:3.9.t Q+=Q1+ Q2, Reactive energy import in the billing period, TOU register
1-0:4.8.0 Q-=Q3+ Q4, Reactive energy export, total register
1-0:4.8.t Q-=Q3+ Q4, Reactive energy export, TOU register
1-0:4.9.0 Q-=Q3+ Q4, Reactive energy export in the billing period, total register
1-0:4.9.t Q-=Q3+ Q4, Reactive energy export in the billing period, TOU register
1-0:5.8.0 Q1, Reactive energy, inductive import, total register
1-0:5.8.t Q1, Reactive energy, inductive import, TOU register
1-0:5.9.0 Q1, Reactive energy, inductive import in the billing period, total register
1-0:5.9.t Q1, Reactive energy, inductive import in the billing period, TOU register
1-0:6.8.0 Q2, Reactive energy, capacitive import, total register
1-0:6.8.t Q2, Reactive energy, capacitive import, TOU register
1-0:6.9.0 Q2, Reactive energy, capacitive import in the billing period, total register
1-0:6.9.t Q2, Reactive energy, capacitive import in the billing period, TOU register
1-0:7.8.0 Q3, Reactive energy, inductive export, total register
1-0:7.8.t Q3, Reactive energy, inductive export, TOU register
1-0:7.9.0 Q3, Reactive energy, inductive export in the billing period, total register
1-0:7.9.t Q3, Reactive energy, inductive export in the billing period, TOU register
1-0:8.8.0 Q4, Reactive energy, capacitive export, total register
1-0:8.8.t Q4, Reactive energy, capacitive export, TOU register
1-0:8.9.0 Q4, Reactive energy, capacitive export in the billing period, total register
1-0:8.9.t Q4, Reactive energy, capacitive export in the billing period, TOU register
1-0:9.8.0 S+, Apparent energy import, total register
1-0:9.8.t S+, Apparent energy import, TOU register
1-0:9.9.0 S+, Apparent energy import in the billing period, total register
1-0:9.9.t S+, Apparent energy import in the billing period, TOU register
1-0:10.8.0 S-, Apparent energy export, total register
1-0:10.8.t S-, Apparent energy export, TOU register
1-0:10.9.0 S-, Apparent energy export in the billing period, total register
1-0:10.9.t S-, Apparent energy export in the billing period, TOU register
Three phases cumulative demand registers, t = TOU registers (1,..n)
1-0:1.2.0 P+ cumulative demand total register
1-0:1.2.t P+ cumulative demand TOU register
1-0:2.2.0 P- cumulative demand total register
1-0:2.2.t P- cumulative demand TOU register
1-0:3.2.0 Q+ cumulative demand total register
1-0:3.2.t Q+ cumulative demand TOU register
1-0:4.2.0 Q- cumulative demand total register
1-0:4.2.t Q- cumulative demand TOU register
36
1-0:5.2.0 Q1 cumulative demand total register

1-0:5.2.t Q1 cumulative demand TOU register
1-0:9.2.0 S+ cumulative demand total register
1-0:9.2.t S+ cumulative demand TOU register
1-0:10.2.0 S- cumulative demand total register
1-0:10.2.t S- cumulative demand TOU register
Three phases momentary demand registers
1-0:1.4.0 P+ momentary demand register
1-0:2.4.0 P- momentary demand register
1-0:3.4.0 Q+ momentary demand register
1-0:4.4.0 Q- momentary demand register
1-0:5.4.0 Q1 momentary demand register
1-0:9.4.0 S+ momentary demand register
1-0:10.4.0 S- momentary demand register
Three phases last ended measurement period demand register
1-0:1.5.0 P+ last ended measurement period demand register
1-0:2.5.0 P- last ended measurement period demand register
1-0:3.5.0 Q+ last ended measurement period demand register
1-0:4.5.0 Q- last ended measurement period demand register
1-0:5.5.0 Q1 last ended measurement period demand register
1-0:9.5.0 S+ last ended measurement period demand register
1-0:10.5.0 S- last ended measurement period demand register
Three phases maximum demand registers, t = TOU registers (1,..n)
1-0:1.6.0 P+ maximum demand total register
1-0:1.6.t P+ maximum demand TOU register
1-0:2.6.0 P- maximum demand total register
1-0:2.6.t P- maximum demand TOU register
1-0:3.6.0 Q+ maximum demand total register
1-0:3.6.t Q+ maximum demand TOU register
1-0:4.6.0 Q- maximum demand total register
1-0:4.6.t Q- maximum demand TOU register
1-0:5.6.0 Q1 maximum demand total register
1-0:5.6.t Q1 maximum demand TOU register
1-0:9.6.0 S+ maximum demand total register
1-0:9.6.t S+ maximum demand TOU register
1-0:10.6.0 S- maximum demand total register
37
1-0:10.6.t S- maximum demand TOU register

Three phases quality instantaneous registers
1-0:11.7.0 Average current RMS
1-0:12.7.0 Average voltage RMS
1-0:13.7.0 Average power factor
1-0:14.7.0 Average frequency
1-0:11.7.h Average harmonics component in current, h – harmonics component (1, ..,8)
1-0:12.7.h Average harmonics component in voltage, h – harmonics component (1, ..,8)
1-0: 15.7.0 ΣLi Active power (abs(QI+QIV)+(abs(QII+QIII))
Phase R energy registers, t = TOU registers (1,..n)
1-0:21.8.0 A+, Active energy import in phase R, total register
1-0:21.8.t A+, Active energy import in phase R, TOU register
1-0:21.9.0 A+, Active energy import in the billing period, phase R
1-0:21.9.t A+, Active energy import in the billing period TOU register, phase R
1-0:22.8.0 A-, Active energy export in phase R, total register
1-0:22.8.t A-, Active energy export in phase R, TOU register
1-0:22.9.0 A-, Active energy export in the billing period, phase R
1-0:22.9.t A-, Active energy export in the billing period TOU register, phase R
1-0:23.8.0 Q+=Q1+ Q2, Reactive energy import in phase R, total register
1-0:23.8.t Q+=Q1+ Q2, Reactive energy import in phase R, TOU register
1-0:23.9.0 Q+=Q1+ Q2, Reactive energy import in the billing period, phase R
1-0:23.9.t Q+=Q1+ Q2, Reactive energy import in the billing period TOU register, phase R
1-0:24.8.0 Q-=Q3+ Q4, Reactive energy export in phase R, total register
1-0:24.8.t Q-=Q3+ Q4, Reactive energy export in phase R, TOU register
1-0:24.9.0 Q-=Q3+ Q4, Reactive energy export in the billing period, phase R
1-0:24.9.t Q-=Q3+ Q4, Reactive energy export in the billing period TOU register, phase R
1-0:25.8.0 Q1, Reactive energy, inductive import in phase R, total register
1-0:25.8.t Q1, Reactive energy, inductive import in phase R, TOU register
1-0:25.9.0 Q1, Reactive energy, inductive import in the billing period, phase R
1-0:25.9.t Q1, Reactive energy, inductive import in the billing period TOU register, phase R
1-0:26.8.0 Q2, Reactive energy, capacitive import in phase R, total register
1-0:26.8.t Q2, Reactive energy, capacitive import in phase R, TOU register
1-0:26.9.0 Q2, Reactive energy, capacitive import in the billing period, phase R
1-0:26.9.t Q2, Reactive energy, capacitive import in the billing period TOU register, phase
1-0:27.8.0 R
Q3, Reactive energy, inductive export in phase R, total register
1-0:27.8.t Q3, Reactive energy, inductive export in phase R, TOU register
1-0:27.9.0 Q3, Reactive energy, inductive export in the billing period, phase R
1-0:27.9.t Q3, Reactive energy, inductive export in the billing period TOU register, phase R
1-0:28.8.0 Q4, Reactive energy, capacitive export in phase R, total register
1-0:28.8.t Q4, Reactive energy, capacitive export in phase R, TOU register
1-0:28.9.0 Q4, Reactive energy, capacitive export in the billing period, phase R
1-0:28.9.t Q4, Reactive energy, capacitive export in the billing period TOU register, phase
1-0:29.8.0 R
S+, Apparent energy import in phase R, total register
1-0:29.8.t S+, Apparent energy import in phase R, TOU register
1-0:29.9.0 S+, Apparent energy import in the billing period, phase R
1-0:29.9.t S+, Apparent energy import in the billing period TOU register, phase R
1-0:30.8.0 S- Apparent energy export in phase R, total register
1-0:30.8.t S- Apparent energy export in phase R, TOU register
1-0:30.9.0 S-, Apparent energy export in the billing period, phase R
1-0:30.9.t S-, Apparent energy export in the billing period TOU register, phase R
Phase R cumulative demand register, t = TOU registers (1,..n)
1-0:21.2.0 P+ cumulative demand in phase R total register
1-0:21.2.t P+ cumulative demand in phase R TOU register
1-0:22.2.0 P- cumulative demand in phase R total register
38
1-0:22.2.t P- cumulative demand in phase R TOU register

1-0:23.2.0 Q+ cumulative demand in phase R total register
1-0:23.2.t Q+ cumulative demand in phase R TOU register
1-0:24.2.0 Q- cumulative demand in phase R total register
1-0:24.2.t Q- cumulative demand in phase R TOU register
1-0:25.2.0 Q1 cumulative demand in phase R total register
1-0:25.2.t Q1 cumulative demand in phase R TOU register
1-0:29.2.0 S+ cumulative demand in phase R total register
1-0:29.2.t S+ cumulative demand in phase R TOU register
1-0:30.2.0 S- cumulative demand in phase R total register
1-0:30.2.t S- cumulative demand in phase R TOU register
Phase R momentary demand register
1-0:21.4.0 P+ momentary demand in phase R register
1-0:22.4.0 P- momentary demand in phase R register
1-0:23.4.0 Q+ momentary demand in phase R register
1-0:24.4.0 Q- momentary demand in phase R register
1-0:25.4.0 Q1 momentary demand in phase R register
1-0:29.4.0 S+ momentary demand in phase R register
1-0:30.4.0 S- momentary demand in phase R register
Phase R last ended measurement period demand register
1-0:21.5.0 P+ last ended measurement period in phase R demand register
1-0:22.5.0 P- last ended measurement period in phase R demand register
1-0:23.5.0 Q+ last ended measurement period in phase R demand register
1-0:24.5.0 Q- last ended measurement period in phase R demand register
1-0:25.5.0 Q1 last ended measurement period in phase R demand register
1-0:29.5.0 S+ last ended measurement period in phase R demand register
1-0:30.5.0 S- last ended measurement period in phase R demand register
Phase R maximum demand registers, t = TOU registers (1,..n)
1-0:21.6.0 P+ maximum demand in phase R register
1-0:21.6.t P+ maximum demand in phase R TOU register
1-0:22.6.0 P- maximum demand in phase R register
1-0:22.6.t P- maximum demand in phase R TOU register
1-0:23.6.0 Q+ maximum demand in phase R register
1-0:23.6.t Q+ maximum demand in phase R TOU register
1-0:24.6.0 Q- maximum demand in phase R register
1-0:24.6.t Q- maximum demand in phase R TOU register
1-0:25.6.0 Q1 maximum demand in phase R register
1-0:25.6.t Q1 maximum demand in phase R TOU register
39

1-0:29.6.0 S+ maximum demand in phase R register
1-0:29.6.t S+ maximum demand in phase R TOU register
1-0:30.6.0 S- maximum demand in phase R register
1-0:30.6.t S- maximum demand in phase R TOU register
Phase R quality instantaneous registers
1-0:31.7.0 Average current RMS in phase R
1-0:32.7.0 Average voltage RMS in phase R
1-0:33.7.0 Average power factor in phase R
1-0:34.7.0 Average frequency in phase R
1-0:31.7.h Average harmonics component in current, h – harmonics component (1, ..,8) in
phase R
1-0:32.7.h Average harmonics component in voltage, h – harmonics component (1, ..,8) in
phase R
1-0:81.7.40 Phase angle in phase R
Phase S energy registers, t = TOU registers (1,..n)
1-0:41.8.0 A+, Active energy import in phase S, total register
1-0:41.8.t A+, Active energy import in phase S, total register
1-0:41.9.0 A+, Active energy import in the billing period, phase S
1-0:41.9.t A+, Active energy import in the billing period, phase S
1-0:42.8.0 A-, Active energy export in phase S, total register
1-0:42.8.t A-, Active energy export in phase S, total register
1-0:42.9.0 A-, Active energy export in the billing period, phase S
1-0:42.9.t A-, Active energy export in the billing period, phase S
1-0:43.8.0 Q+=Q1+ Q2, Reactive energy import in phase S, total register
1-0:43.8.t Q+=Q1+ Q2, Reactive energy import in phase S, total register
1-0:43.9.0 Q+=Q1+ Q2, Reactive energy import in the billing period, phase S
1-0:43.9.t Q+=Q1+ Q2, Reactive energy import in the billing period, phase S
1-0:44.8.0 Q-=Q3+ Q4, Reactive energy export in phase S, total register
1-0:44.8.t Q-=Q3+ Q4, Reactive energy export in phase S, total register
1-0:44.9.0 Q-=Q3+ Q4, Reactive energy export in the billing period, phase S
1-0:44.9.t Q-=Q3+ Q4, Reactive energy export in the billing period, phase S
1-0:45.8.0 Q1, Reactive energy, inductive import in phase S, total register
1-0:45.8.t Q1, Reactive energy, inductive import in phase S, total register
1-0:45.9.0 Q1, Reactive energy, inductive import in the billing period, phase S
1-0:45.9.t Q1, Reactive energy, inductive import in the billing period, phase S
1-0:46.8.0 Q2, Reactive energy, capacitive import in phase S, total register
1-0:46.8.t Q2, Reactive energy, capacitive import in phase S, total register
1-0:46.9.0 Q2, Reactive energy, capacitive import in the billing period, phase S
1-0:46.9.t Q2, Reactive energy, capacitive import in the billing period, phase S
1-0:47.8.0 Q3, Reactive energy, inductive export in phase S, total register
1-0:47.8.t Q3, Reactive energy, inductive export in phase S, total register
1-0:47.9.0 Q3, Reactive energy, inductive export in the billing period, phase S
1-0:47.9.t Q3, Reactive energy, inductive export in the billing period, phase S
1-0:48.8.0 Q4, Reactive energy, capacitive export in phase S, total register
1-0:48.8.t Q4, Reactive energy, capacitive export in phase S, total register
1-0:48.9.0 Q4, Reactive energy, capacitive export in the billing period, phase S
1-0:48.9.t Q4, Reactive energy, capacitive export in the billing period, phase S
1-0:49.8.0 S+, Apparent energy import in phase S, total register
1-0:49.8.t S+, Apparent energy import in phase S, total register
1-0:49.9.0 S+, Apparent energy import in the billing period, phase S
1-0:49.9.t S+, Apparent energy import in the billing period, phase S
1-0:50.8.0 S-, Apparent energy export in phase S, total register
40
1-0:50.8.t S-, Apparent energy export in phase S, total register

1-0:50.9.0 S-, Apparent energy export in the billing period, phase S
1-0:50.9.t S-, Apparent energy export in the billing period, phase S
Phase S momentary demand register
1-0:41.4.0 P+ momentary demand in phase S register
1-0:42.4.0 P- momentary demand in phase S register
1-0:43.4.0 Q+ momentary demand in phase S register
1-0:44.4.0 Q- momentary demand in phase S register
1-0:45.4.0 Q1 momentary demand in phase S register
1-0:49.4.0 S+ momentary demand in phase S register
1-0:50.4.0 S- momentary demand in phase S register
Phase S last ended measurement period demand register
1-0:41.5.0 P+ last ended measurement period in phase S demand register
1-0:42.5.0 P- last ended measurement period in phase S demand register
1-0:43.5.0 Q+ last ended measurement period in phase S demand register
1-0:44.5.0 Q- last ended measurement period in phase S demand register
1-0:45.5.0 Q1 last ended measurement period in phase S demand register
1-0:49.5.0 S+ last ended measurement period in phase S demand register
1-0:50.5.0 S- last ended measurement period in phase S demand register
Phase S maximum demand registers, t = TOU registers (1,..n)
1-0:41.6.0 P+ maximum demand in phase S register
1-0:41.6.t P+ maximum demand in phase S TOU register
1-0:42.6.0 P- maximum demand in phase S register
1-0:42.6.t P- maximum demand in phase S TOU register
1-0:43.6.0 Q+ maximum demand in phase S register
1-0:43.6.t Q+ maximum demand in phase S TOU register
1-0:44.6.0 Q- maximum demand in phase S register
1-0:44.6.t Q- maximum demand in phase S TOU register
1-0:45.6.0 Q1 maximum demand in phase S register
1-0:45.6.t Q1 maximum demand in phase S TOU register
1-0:49.6.0 S+ maximum demand in phase S register
1-0:49.6.t S+ maximum demand in phase S TOU register
1-0:50.6.0 S- maximum demand in phase S register
1-0:50.6.t S- maximum demand in phase S TOU register
Phase S quality instantaneous registers
1-0:51.7.0 Average current RMS in phase S
1-0:52.7.0 Average voltage RMS in phase S
1-0:53.7.0 Average power factor in phase S
1-0:54.7.0 Average frequency in phase S
phase S
41

phase S
1-0:81.7.51 Phase angle in phase S
Phase T energy registers, t = TOU registers (1,..n)
1-0:61.8.0 A+, Active energy import in phase T, total register
1-0:61.8.t A+, Active energy import in phase T, total register
1-0:61.9.0 A+, Active energy import in the billing period, phase T
1-0:61.9.t A+, Active energy import in the billing period, phase T
1-0:62.8.0 A-, Active energy export in phase T, total register
1-0:62.8.t A-, Active energy export in phase T, total register
1-0:62.9.0 A-, Active energy export in the billing period, phase T
1-0:62.9.t A-, Active energy export in the billing period, phase T
1-0:63.8.0 Q+=Q1+ Q2, Reactive energy import in phase T, total register
1-0:63.8.t Q+=Q1+ Q2, Reactive energy import in phase T, total register
1-0:63.9.0 Q+=Q1+ Q2, Reactive energy import in the billing period, phase T
1-0:63.9.t Q+=Q1+ Q2, Reactive energy import in the billing period, phase T
1-0:64.8.0 Q-=Q3+ Q4, Reactive energy export in phase T, total register
1-0:64.8.t Q-=Q3+ Q4, Reactive energy export in phase T, total register
1-0:64.9.0 Q-=Q3+ Q4, Reactive energy export in the billing period, phase T
1-0:64.9.t Q-=Q3+ Q4, Reactive energy export in the billing period, phase T
1-0:65.8.0 Q1, Reactive energy, inductive import in phase T, total register
1-0:65.8.t Q1, Reactive energy, inductive import in phase T, total register
1-0:65.9.0 Q1, Reactive energy, inductive import in the billing period, phase T
1-0:65.9.t Q1, Reactive energy, inductive import in the billing period, phase T
1-0:66.8.0 Q2, Reactive energy, capacitive import in phase T, total register
1-0:66.8.t Q2, Reactive energy, capacitive import in phase T, total register
1-0:66.9.0 Q2, Reactive energy, capacitive import in the billing period, phase T
1-0:66.9.t Q2, Reactive energy, capacitive import in the billing period, phase T
1-0:67.8.0 Q3, Reactive energy, inductive export in phase T, total register
1-0:67.8.t Q3, Reactive energy, inductive export in phase T, total register
1-0:67.9.0 Q3, Reactive energy, inductive export in the billing period, phase T
1-0:67.9.t Q3, Reactive energy, inductive export in the billing period, phase T
1-0:68.8.0 Q4, Reactive energy, capacitive export in phase T, total register
1-0:68.8.t Q4, Reactive energy, capacitive export in phase T, total register
1-0:68.9.0 Q4, Reactive energy, capacitive export in the billing period, phase T
1-0:68.9.t Q4, Reactive energy, capacitive export in the billing period, phase T
1-0:69.8.0 S+, Apparent energy import in phase T, total register
1-0:69.8.t S+, Apparent energy import in phase T, total register
1-0:69.9.0 S+, Apparent energy import in the billing period, phase T
1-0:69.9.t S+, Apparent energy import in the billing period, phase T
1-0:70.8.0 S-, Apparent energy export in phase T, total register
1-0:70.8.t S-, Apparent energy export in phase T, total register
1-0:70.9.0 S-, Apparent energy export in the billing period, phase T
1-0:70.9.t S-, Apparent energy export in the billing period, phase T
Phase T momentary demand register
1-0:61.4.0 P+ momentary demand in phase T register
1-0:62.4.0 P- momentary demand in phase T register
1-0:63.4.0 Q+ momentary demand in phase T register
1-0:64.4.0 Q- momentary demand in phase T register
1-0:65.4.0 Q1 momentary demand in phase T register
1-0:69.4.0 S+ momentary demand in phase T register
42
1-0:70.4.0 S- momentary demand in phase T register

Phase T last ended measurement period demand register
1-0:61.5.0 P+ last ended measurement period in phase T demand register
1-0:62.5.0 P- last ended measurement period in phase T demand register
1-0:63.5.0 Q+ last ended measurement period in phase T demand register
1-0:64.5.0 Q- last ended measurement period in phase T demand register
1-0:65.5.0 Q1 last ended measurement period in phase T demand register
1-0:69.5.0 S+ last ended measurement period in phase T demand register
1-0:70.5.0 S- last ended measurement period in phase T demand register
Phase T maximum demand registers, t = TOU registers (1,..n)
1-0:61.6.0 P+ maximum demand in phase T register
1-0:61.6.t P+ maximum demand in phase T TOU register
1-0:62.6.0 P+ maximum demand in phase T register
1-0:62.6.t P- maximum demand in phase T TOU register
1-0:63.6.0 Q+ maximum demand in phase T register
1-0:63.6.t Q+ maximum demand in phase T TOU register
1-0:64.6.0 Q- maximum demand in phase T register
1-0:64.6.t Q- maximum demand in phase T TOU register
1-0:65.6.0 Q1 maximum demand in phase T register
1-0:65.6.t Q1 maximum demand in phase T TOU register
1-0:69.6.0 S+ maximum demand in phase T register
1-0:69.6.t S+ maximum demand in phase T TOU register
1-0:70.6.0 S- maximum demand in phase T register
1-0:70.6.t S- maximum demand in phase T TOU register
Phase T quality instantaneous registers
1-0:71.7.0 Average current RMS in phase T
1-0:72.7.0 Average voltage RMS in phase T
1-0:73.7.0 Average power factor in phase T
1-0:74.7.0 Average frequency in phase T
phase T
phase T
1-0:81.7.62 Phase angle in phase T
Appendix B: Log book events

LB code Data name
LB.0080 Power down
LB.0040 Power up
43

LB.0020 RTC Set
LB.0008 DST
LB.8118 Watch dog
LB.8119 Fraud start
LB.811A Fraud end
LB.8152 Current without Voltage phase L1 - start
LB.8154 Current without Voltage phase L3 - start
LB.8155 Current without Voltage phase L1 - end
LB.815E Wrong password login
LB.815F Password changed
LB.8158 jhkhjk module inserted - bad
COM
LB.8159 COM module inserted - OK
LB.815A COM module out
LB.815B IO module inserted - bad
LB.815C IO module inserted - OK
LB.815D IO module out
ghjhgjghjghj
LB.8160 Start
ghjghjDST changed
LB.8161 End
ghjghjDST changed
LB.8162 Low battery
ghjghjghj
LB.8163 Inverted current start phase L1
ghjghjghjghjghjghjghjgghjghjghj
LB.8164 Inverted current end phase L1
LB.8169 Unbalanced by current start
LB.816A Unbalanced by current end
LB.816B Unbalanced by voltage start
44
LB.816C Unbalanced by voltage end

LB.816D External alarm
LB.816E Alarm output set
LB.8171 External alarm 2
Appendix C: Connection diagrams
Connection diagram for direct connected meter
Connection diagram for indirect connected meter (4-wire connection, connection via current and (or) voltage
transformer)
Connection diagram for indirect connected meter (3-wire connection, connection via current and voltage transformer)
45
Connection diagram for indirect connected meter (3P3W connection, connection via current and voltage transformer)
Note: Such connection could be used only for maximal nominal voltage 3x230V and with vector registration
only!
Owing to periodical improvements of our products the supplied products can differ in some details from the data stated in the prospectus material.
Iskraemeco d.d., Energy Measurement and Management
4000 Kranj, Savska loka 4, Slovenia
Telephone (+386 4) 206 40 00, Fax: (+386 4) 206 43 76
http://www.iskraemeco.si, E-mail: [email protected]
Published by Iskraemeco. Data subject to alteration without notice. MT830/MT831 -Eng V1.2.doc
46

Energy Measurement

Uploaded by

Copyright:

Available Formats

Energy Measurement

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Energy Measurement

Uploaded by

Copyright:

Available Formats

Energy measurement

MT83x Communication specifications IEC62056-21

COMMON REMARKS TO COMMUNICATION PROTOCOL

3. Supported commands are:

 “Bmn” bitmap, n Octets

List of er_ (errata) info

16969 ms elapsed -> IEC1107 opening local connection

1172 ms elapsed -> IEC62056-21 received:

203 ms elapsed -> IEC62056-21 sending:

219 ms elapsed -> IEC62056-21 changing baudrate to 9600:

4. LOG-BOOK event recorder

LogBook event recorder has place for 255 events.

LB code Data name

LB.812E Contract1 billing reset

 <SOH>R5<STX>P.98(TSTs11; TSTs11) - Read “from – to” in one block

P.98(TSTs13)(Sn) - the oldest LogBook event

16 ms elapsed -> IEC62056-21 sending:

1172 ms elapsed -> IEC62056-21 received:

203 ms elapsed -> IEC62056-21 sending:

219 ms elapsed -> IEC62056-21 changing baudrate to 9600:

2. R5 command - “from – to”

54266 ms elapsed -> IEC1107 opening local connection

1172 ms elapsed -> IEC62056-21 received:

203 ms elapsed -> IEC62056-21 sending:

219 ms elapsed -> IEC62056-21 changing baudrate to 9600:

3. R6 command  block reading

59844 ms elapsed -> IEC1107 opening local connection

1171 ms elapsed -> IEC62056-21 received:

204 ms elapsed -> IEC62056-21 sending:

218 ms elapsed -> IEC62056-21 changing baudrate to 9600:

4. R6 command - “from – to” block reading

47359 ms elapsed -> IEC1107 opening local connection

1156 ms elapsed -> IEC62056-21 received:

203 ms elapsed -> IEC62056-21 sending:

219 ms elapsed -> IEC62056-21 changing baudrate to 9600:

Billing reset (MD reset)

Billing reset can be performed via communication interface by E2 command.

SOH E 2 STX 0.0.5.0.4.0 ETX BCC

23859 ms elapsed -> IEC1107 opening local connection

1172 ms elapsed -> IEC62056-21 received:

203 ms elapsed -> IEC62056-21 sending:

219 ms elapsed -> IEC62056-21 changing baudrate to 9600:

 <SOH>R5<STX>P.01(;) LP all – from beginning till the end, all channels

 <SOH>R5<STX>P.01(TSTs11;TSTs11) LP “from – to”, all channels

 <SOH>R6<STX>P.01(;;N) LP in blocks with N records per block, all channels

 <SOH>R6<STX>P.01(TSTs11;TSTs11;N) LP “from-to” in blocks with N records per block

TSTs11 = (sYYMMDDhhmm) - s = season (0 = winter, 1 = summer)

1. Reading all LP with R5 command

23/08/2005 14:41:18, Log Started

10735 ms elapsed -> IEC1107 opening local connection

1022 ms elapsed -> IEC1107 received:

200 ms elapsed -> IEC1107 sending:

210 ms elapsed -> IEC1107 changing baudrate to 9600:

and with R6 command

23/08/2005 14:42:51, Log Started

11877 ms elapsed -> IEC1107 opening local connection

1031 ms elapsed -> IEC1107 received:

201 ms elapsed -> IEC1107 sending:

210 ms elapsed -> IEC1107 changing baudrate to 9600: