Scribd
Upload
43 views11 pages

Microprocessors System Interfacing

The document describes code for a PIC18F452 microcontroller to generate rectangular waves and implement a radar system. It includes code to generate rectangular waves at different frequencies and duty cycles using Timer0 interrupts. It also includes code for a radar system that listens for a high sensor value, generates a 300ms pulse when detected, and uses Timer0 for the delay.

Uploaded by

KASHIF zaman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
43 views11 pages

Microprocessors System Interfacing

The document describes code for a PIC18F452 microcontroller to generate rectangular waves and implement a radar system. It includes code to generate rectangular waves at different frequencies and duty cycles using Timer0 interrupts. It also includes code for a radar system that listens for a high sensor value, generates a 300ms pulse when detected, and uses Timer0 for the delay.

Uploaded by

KASHIF zaman
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

Microprocessors System Interfacing

Question 1:
Generate a rectangular wave with PIC18F452 microcontroller with following
requirements.

i. Frequency=200Hz , Duty Cycle =20% & XTAL =20 MHz

Code:

LIST P=PIC18F452, F=INHX32, N=0, ST=OFF, R=HEX


config OSC=HS, OSCS=OFF, WDT=OFF, BORV=45, PWRT=ON,
BOR=ON, DEBUG=OFF, LVP=OFF, STVR=OFF
#include<p18f452.inc>
ORG 0h
Main:
CLRF TRISB ; Port B pins as output
MOVLW 0x08
MOVWF T0CON ; Timer0, 16 bit, no prescaler
CLRF PORTB
Loop:
BSF PORTB,0 ; Drive RB0 high
CALL Delayon ; 1 ms delay
BCF PORTB,0 ; Drive RB0 low
CALL Delayoff ; 4 ms delay
GOTO Loop

Delayon: ; 1 ms delay
BSF T0CON,7 ; Timer 0 on
MOVLW 0xEC ; Load 0xEC78 for 1 ms delay
MOVWF TMR0H
MOVLW 0x78

PAGE 1
MOVWF TMR0L
Again:
BTFSS INTCON,2 ; Wait till TMR0IF flag set
GOTO Again
BCF T0CON,7 ; Timer 0 off
BCF INTCON,2 ; Clear flag
RETURN

Delayoff: ; 4 ms delay
BSF T0CON,7 ; Timer0 on
MOVLW 0xB1 ; Load 0xB1E0 for 4 ms delay
MOVWF TMR0H
MOVLW 0xE0
MOVWF TMR0L
Check:
BTFSS INTCON,2 ; Wait till TMR0IF flag set
GOTO Check
BCF T0CON,7 ; Timer0 off
BCF INTCON,2 ; Clear flag
RETURN
END

ii. Frequency=50Hz , Duty Cycle =25% & XTAL =40 MHz

LIST P=PIC18F452, F=INHX32, N=0, ST=OFF, R=HEX


config OSC=HS, OSCS=OFF, WDT=OFF, BORV=45, PWRT=ON, BOR=ON,
DEBUG=OFF, LVP=OFF, STVR=OFF
#include<p18f452.inc>
ORG 0H

PAGE 2
Main:
CLRF TRISB ; Port B pins as output
MOVLW 0x02
MOVWF T0CON ; Timer0, 16 bit, prescaler 8
CLRF PORTB
Loop:
BSF PORTB,0 ; Drive RB0 high
CALL Delayon ; 5 ms delay
BCF PORTB,0 ; Drive RB0 low
CALL Delayoff ; 20 ms delay
GOTO Loop

Delayon: ; 5 ms delay
BSF T0CON,7 ; Timer 0 on
MOVLW 0xE7 ; Load 0xE796 for 5 ms delay
MOVWF TMR0H
MOVLW 0x96
MOVWF TMR0L
Again:
BTFSS INTCON,2 ; Wait till TMR0IF flag set
GOTO Again
BCF T0CON,7 ; Timer 0 off
BCF INTCON,2 ; Clear flag
RETURN

Delayoff: ; 15 ms delay
BSF T0CON,7 ; Timer0 on
MOVLW 0xB6 ; Load 0xB6C2 for 15 ms delay
MOVWF TMR0H

PAGE 3
MOVLW 0xC2
MOVWF TMR0L
Check:
BTFSS INTCON,2 ; Wait till TMR0IF flag set
GOTO Check
BCF T0CON,7 ; Timer0 off
BCF INTCON,2 ; Clear flag
RETURN
END

iii. Frequency=1Hz , Duty Cycle =50% & XTAL =40 MHz

LIST P=PIC18F452, F=INHX32, N=0, ST=OFF, R=HEX


config OSC=HS, OSCS=OFF, WDT=OFF, BORV=45, PWRT=ON, BOR=ON,
DEBUG=OFF, LVP=OFF, STVR=OFF
#include<p18f452.inc>
ORG 0H
Main:
CLRF TRISB ; Port B pins as output
MOVLW 0x07
MOVWF T0CON ; Timer0, 16 bit, prescaler 256
CLRF PORTB
Loop:
BSF PORTB,0 ; Drive RB0 high
CALL Delay ; .5s delay
BCF PORTB,0 ; Drive RB0 low
CALL Delay ; .5s delay
GOTO Loop

Delay: ; .5 s delay

PAGE 4
BSF T0CON,7 ; Timer 0 on
MOVLW 0xB3 ; Load 0xB3B5 for .5s delay
MOVWF TMR0H
MOVLW 0xB5
MOVWF TMR0L
Again:
BTFSS INTCON,2 ; Wait till TMR0IF flag set
GOTO Again
BCF T0CON,7 ; Timer 0 off
BCF INTCON,2 ; Clear flag
RETURN
END

iv. Frequency=4Hz , Duty Cycle =25% & XTAL =20 MHz

LIST P=PIC18F452, F=INHX32, N=0, ST=OFF, R=HEX


config OSC=HS, OSCS=OFF, WDT=OFF, BORV=45, PWRT=ON, BOR=ON,
DEBUG=OFF, LVP=OFF, STVR=OFF
#include<p18f452.inc>
ORG 0H
Main:
CLRF TRISB ; Port B pins as output
MOVLW 0x04
MOVWF T0CON ; Timer0, 16 bit, prescaler 32
CLRF PORTB
Loop:
BSF PORTB,0 ; Drive RB0 high
CALL Delayon ; 62.5 ms delay
BCF PORTB,0 ; Drive RB0 low
CALL Delayoff ; 187.5 ms delay

PAGE 5
GOTO Loop

Delayon: ; 62.5 ms delay


BSF T0CON,7 ; Timer 0 on
MOVLW 0xD9 ; Load 0x for 62.5 ms delay
MOVWF TMR0H
MOVLW 0xDA
MOVWF TMR0L
Again:
BTFSS INTCON,2 ; Wait till TMR0IF flag set
GOTO Again
BCF T0CON,7 ; Timer 0 off
BCF INTCON,2 ; Clear flag
RETURN

Delayoff: ; 187.5 ms delay


BSF T0CON,7 ; Timer0 on
MOVLW 0x8D ; Load 0xB6C2 for 187.5 ms delay
MOVWF TMR0H
MOVLW 0x8F
MOVWF TMR0L
Check:
BTFSS INTCON,2 ; Wait till TMR0IF flag set
GOTO Check
BCF T0CON,7 ; Timer0 off
BCF INTCON,2 ; Clear flag
RETURN
END

PAGE 6
PAGE 7
QUESTION 2
Implement a RADAR System using PIC18F452. Radar system uses a listening
sensor and listens for high value from sensor. Once it detects high value from sensor
it will generate a pulse with duration of 300ms. Use XTAL=24 MHz with PIC18F452

Code

#include<p18f452.inc>
ORG 0H
start
CLRF TRISB ; Port B as output
BSF TRISD,0 ; RD0 as input

PAGE 8
MOVLW 0x05
MOVWF T0CON ; Timer0, 16 bit with prescaler 64
CLRF PORTB
Loop:
BTFSS PORTD,0 ; Check whether high value from sensor
GOTO Loop ; If not then check again
BSF PORTB,0 ; If yes then drive RB0 high
CALL Delay ; Call Delay subroutine of 300 ms delay
BCF PORTB,0 ; Drive RB0 Low
GOTO Loop
Delay: ; Delay subroutine
MOVLW 0x92
MOVWF TMR0H ; Move the value 37411 which is 0x9223 to TMR0
MOVLW 0x23
MOVWF TMR0L
BSF T0CON,7 ; Timer0 On
Again:
BTFSS INTCON,2 ; Check whether TMR0IF is set
GOTO Again ; Check till it is set
BCF T0CON,7 ; Timer0 off
BCF INTCON,2 ; TMR0IF cleared
RETURN
END

PAGE 9
PAGE 10

You might also like