Scribd
Upload
798 views3 pages

Ether Injection Control Solenoid

Uploaded by

Blowby High
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
798 views3 pages

Ether Injection Control Solenoid

Uploaded by

Blowby High
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

10/26/2020 SIS 2.

2013/10/24 Ether Starting Aid - Test (UENR0500)

SMCS - 1456 i05528251


Before you test the ether injection system, remove the ether canister from the system.

Use this procedure in order to troubleshoot the ether system or use this procedure if a
diagnostic code in Table 1 is active or logged.

Diagnostic Trouble Codes


CDL J1939 Code Descriptions Comments
Code Code (code descriptions may vary)
The code is latched. The
2417-5 Ether Injection Control Solenoid : code is logged.
626-5
Current Below Normal Ether injection is disabled.

The code is latched. The


2417-6 Ether Injection Control Solenoid : code is logged.
626-6
Current Above Normal Ether injection is disabled.

Table 1

The ether injection system improves cold weather starting of the engine. The ECM controls
the ether injection system. The ether injection system is enabled when all of the following
conditions occur:

The configuration parameter is enabled or the configuration parameter is set to


continuous flow.

The intake manifold air temperature is less than 0 °C (32 °F) or the engine coolant
temperature is less than 0 °C (32 °F).

Engine speed is greater than 0 rpm and less than 50 rpm below the low idle speed.

No diagnostic codes are active for both the engine coolant temperature sensor and for
the intake manifold air temperature sensor.

Illustration 1 g03016305
Schematic of the ether injection system

https://sis2.cat.com/#/detail?
keyword=2417&tab=3&serialNumber=twg00766&infoType=7&serviceMediaNumber=UENR0500&serviceIeSystemControlNumber=i05528251
https://sis2.cat.com/#/detail?keyword=2417&tab=3&serialNumber=twg00766&infoType=7&serviceMediaNumber=UENR0500&serviceIeSystemControlNumber=i05528251 1/3
10/26/2020 SIS 2.0

Illustration 2 g02099721
P1 terminals for the ether injection system

(P1-10) Starting aid solenoid

(P1-18) Return for the starting aid solenoid

Illustration 3 g01155187
Terminal locations at the harness connector for the ether solenoid

(1) Starting aid solenoid

(2) Return for the starting aid solenoid

Troubleshooting Test Steps Values Results

https://sis2.cat.com/#/detail?
keyword=2417&tab=3&serialNumber=twg00766&infoType=7&serviceMediaNumber=UENR0500&serviceIeSystemControlNumber=i05528251
https://sis2.cat.com/#/detail?keyword=2417&tab=3&serialNumber=twg00766&infoType=7&serviceMediaNumber=UENR0500&serviceIeSystemControlNumber=i05528251 2/3
10/26/2020 SIS 2.0

Result: The harness


connector was not free of
debris and/or not free of
corrosion.

Repair or replace the


1. Check the Harness Connectors
damaged or corroded
connector.
A. Verify that the keyswitch is in the OFF
position. Loose
Verify that the problem is
connection,
resolved.
B. Disconnect the harness connector for the damaged
If the problem is not
ether solenoid. connector,
resolved, proceed to Test
or debris
Step
C. Check the harness connector for debris and
for corrosion.
Result: The harness
connector was free of
debris and free of
corrosion.

Proceed to Test Step 2.

2. Create an Open at the Harness Connector


for the Ether Injection Solenoid Result: The voltage
measurement is 0 VDC
The ether canister must be removed prior to after activating the ether
performing this procedure. injection system.

A. Turn the keyswitch to the OFF position. There is a problem in the


harness. Repair the
B. Remove the ether canister. harness or replace the
harness.
C. Disconnect the engine harness connector for
the ether control. Verify that the problem is
resolved.
Wiring and
D. Connect a digital voltmeter across the two
harness
terminals on the engine harness connector for Result: The voltage
ether control. measurement is equal to
battery voltage after
A test on Caterpillar Electronic Technician (ET) activating the ether
allows the technician to activate the ether injection system.
system. The test can be activated by selecting
the "Diagnostic Overrides" screen on Cat ET. There is a problem in the
solenoid. Replace the
E. Turn the keyswitch to the ON position. solenoid.

F. Measure the voltage across terminal 1 and Verify that the problem is
terminal 2 of the harness for the ether injection resolved.
solenoid.

Table 2

Complete the procedure in the order in which the steps are listed.

If the procedure corrected the issue, return the engine to service.

If the procedure did not correct the issue, Contact your Cat dealer Technical Communicator
(TC). For further assistance, your TC can confer with the Dealer Solutions Network (DSN).

PIP-11109658
2020/10/26
02:42:00+08:00
i05528251
© 2020 Caterpillar Inc.
Caterpillar:
Confidential Green

https://sis2.cat.com/#/detail?
keyword=2417&tab=3&serialNumber=twg00766&infoType=7&serviceMediaNumber=UENR0500&serviceIeSystemControlNumber=i05528251
https://sis2.cat.com/#/detail?keyword=2417&tab=3&serialNumber=twg00766&infoType=7&serviceMediaNumber=UENR0500&serviceIeSystemControlNumber=i05528251 3/3

You might also like