Energy Efficiency Improvements in Melting Furnaces: Background

ENERGY EFFICIENCY IMPROVEMENTS IN
MELTING FURNACES
VIJAY PRAKASH SAHA, CHAIRMAN, ENERGY SAVING COMMISSION,

WORLD FOUNDRYMEN ORGANISATION
Background
The power required in heating and melting of metals in all types of metallurgical units is
the main area in which 60% to75% of the total power is used in the unit. Hence any
energy conservation activity should concentrate in the melting area so that considerable
amount of energy is saved. This paper discusses various units like the steel plants and
foundries where metal is melted and suggestions are given where energy conservation
measures can be applied to save considerable amount of energy. The paper covers the
foundry operation in more detail as foundries are mostly in the SME sector and in larger
numbers. It is also suggested that units requiring molten iron can relocate to a nearby
place where a blast furnace is located so that molten metal can be transferred to the point
thereby saving almost 350 to 450 units of electrical power per MT of casting made.
Introduction
The alarming situation of CLIMATE CHANGE has resulted in attracting the immediate
attention by every individual and company towards optimising the scarce recourse. The
production of electricity by thermal based units itself is so low and is associated with the
generation of lot of fly ash. Disposal of fly ash is another major problem. The efficiency
of cupola as a melting unit is very high and induction furnace as a superheating unit is
also very high. Thus by employing the method of DUPLEXING in foundries, the total
operation can be made energy efficient. Small activities in a foundry can lead to a
considerable saving of energy. Various measures have been suggested which are practical
and can be adopted without much investment. This paper deals with them in detail.
Energy Pattern in a Foundry

The energy consumption in various operations of a foundry reveals that the major
consumption of electrical energy is in the melting operation.
Energy required for Melting

The theoretical energy required for melting of metals from fundamental calculations is
given in Table 1. The actual power being consumed in a foundry is also given. In some
cases it may be more than that mentioned in the table. This vast difference is in the
operation variables and can be controlled to a large extent by proper planning.
Metal Temp C Theoretical Actual- Actual-
heat kWH/T Gas/Oil Electric
kWH/T kWH/T
Al 750 295 1406-2138 500
Copper 1260 190 1523 334
Grey Iron 1510 340 801 500
SGIron 1649 363 - 606
It is clear from the table that the theoretical Energy required for melting iron is only
340kWH per Ton whereas the actual Power required is around 600 to 900 units. This
vast difference is due to two factors-one inherent in the principle of melting in an
Induction Furnace and the other operational. The inherent reasons in the furnace
include the inefficiency in (i) Electrical Bus bar losses, (ii) Eddy Current losses (iii)
Refractory losses and (iv) Cooling water losses. The operational losses are largely
due to unnecessary and excessive holding of molten metal in the furnace. This will be
discussed later in the paper.
Duplexing
This operation is to use the melting efficiency of Cupola and superheating efficiency
of induction furnace. The net Melting Efficiency by Combining the high efficiency
of melt down of Cupola and super heating efficiency of Induction Furnace is called
the Duplexing operation. This results in the lowest cost per MT of liquid metal
production.
• Cupola as a Meltdown unit is very efficient to the extent of 60 to 70%
• Induction Furnace as a Super Heating Unit is very efficient to the extent of 60 to
70%.
Duplexing principle combines the high efficiency of melt down of Cupola and super
heating efficiency of Induction Furnace resulting in a considerable saving to the Unit.
Casting Rejection
Casting rejection is another major area where considerable amount of energy is wasted.
In fact the casting rejection at the final stage has absorbed all energy in various
operations of the foundry like moulding, core making, melting and pouring, fettling, shot
blasting and sometimes machining. From the energy point of view, a rejection at the
machine shop is of high energy content compared to the one at the casting stage.
Rejection control in a foundry is a big area and involves the study of the production
process at every stage in the foundry. Preparation of Pareto Chart is a short route to
identify the high rejection items and selective process standardisation will give quick
result. In this method the rejection in every item reduces considerably while the steps
taken will improve the general process and helps in the reduction of rejection in all the
components. History cards is another effective tool to identify and follow up the
performance. In this card the history of a casting is recorded from the pattern stage,
methoding stage, moulding process, type of core used, the chemistry and temperature of
metal poured to the process adopted in fettling is recorded. The rejection is recorded at
each batch production and a PDCA technique will yield improvements at each stage. All
the techniques mentioned below can be adopted individually and severally to get the
desired result of lower rejection consistently.
• Pareto analysis of rejection
• Classify high rejection few and trivial many
• Study individual item and individual reason
• Actions on reason-will be general in action and helps in overall process
improvement-like sand fall, cold shut etc
• Individual item-History Card is very useful
Casting Yield
Casting yield is defined as the weight of casting divided by the total weight of metal
poured to the mould. This is generally presented in percentage. This virtually indicates
that how much of metal is converted to saleable casting and how much comes back to the
foundry as gate, runners, risers etc. Higher the Casting Yield, better is the profitability in
the casting. Efforts are always made in improving the Casting Yield by employing better
techniques.
• Consider a foundry with 100MT /month
• Select items to cover 40% of high volume items
• Improve the yield by 5%
• Amount saved= 40MT X 5% X 50,000/MT= Rs.100,000 per month
• The net saving for the Foundry is Re.1.00 per kg of the total output of 100MT
• The competitiveness of a foundry is decided by the energy conservation and waste
reduction activities.
• One unit of energy saved is equal to three units generated
• Unit having respect for energy will survive the international competitiveness
Some of the techniques are briefly described below:
Use of aided feeders

One of the major developments that have taken in reducing the quantity of feeder metal
required to produce sound casting is in the development of aided feeders. The aided
feeder effectively increases the time of solidification of the feeder so that the feed path is
kept open and availability of liquid metal is ensured for a longer time in the riser. There
are two types of feeders- insulating feeders and exothermic feeders. The insulating feeder
will maintain the heat in the feeder so that the cooling of feeder is avoided and the
solidification time of the feeder is extended by a factor of, say, 1.1. An exothermic feeder
initially supplies heat to the metal and increases the temperature of the liquid and later
acts as insulating feeder and prevents the cooling of the feeder. This extends the time of
solidification of the feeder significantly by a factor, say, 1.2. This implies that if a sound
casting is produced by the use of 120mm diameter feeder, it is enough to use a 110mm
dia insulating feeder or a 100mm diameter exothermic feeder. Thus the weight of feeder
reduces considerably and the Casting Yield improves drastically.
Use of Ceramic Foam Filters
The use of ceramic foam filter to increase the casting yield is rarely used and is many a
times considered as a secondary effect and the primary reason for use is removal of
inclusions. In fact the use of ceramic foam filter has improved the yield drastically and
may be that this advantage has not been thought of as the primary effect by the use of
ceramic foam filters. It has been established that use of ceramic foam filters makes the
molten metal flow laminar. Thus use of ceramic foam filters results in dual benefit of
reducing the velocity and turbulence to make the flow laminar and the other effect is the
removal of inclusions to produce clean castings. Earlier designs of gating with a longer
stepped runner bar can be easily be replaced by a shorter and almost near the casting with
a foam filter so that the efficiency of filtration is drastically improved and the weight of
runner bar is reduced. Serious study has to be made in each component to improve the
yield by employing Ceramic Foam Filters.
Review of Gating and Feeding system, Use of softwares for methoding
A very important step in this direction of improving the Casting Yield is systematically
studying the present Gating and Feeding systems, subject it to approval by the use of
software available and to make improvements. This is long drawn exercise in a existing
foundry whereas the method helps in standardisation in a new foundry.
Technical Training and upgradation
Involvement of personnel at all levels in the operation of a foundry is very important.
Continuous training in newer technologies and processes is very essential in the
implementation of all schemes.

Energy Efficiency Improvements in Melting Furnaces: Background

Uploaded by

Copyright:

Available Formats

Energy Efficiency Improvements in Melting Furnaces: Background

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Energy Efficiency Improvements in Melting Furnaces: Background

Uploaded by

Copyright:

Available Formats

ENERGY EFFICIENCY IMPROVEMENTS IN

VIJAY PRAKASH SAHA, CHAIRMAN, ENERGY SAVING COMMISSION,

Energy Pattern in a Foundry

Energy required for Melting

Al 750 295 1406-2138 500

Copper 1260 190 1523 334

Grey Iron 1510 340 801 500

SGIron 1649 363 - 606

Some of the techniques are briefly described below:

Use of aided feeders

You might also like