Grundfosliterature 1191206

Download as pdf or txt
Download as pdf or txt
You are on page 1of 80

GRUNDFOS DATA BOOKLET

S pumps, range 62
15 to 50 kW
50 Hz
S pumps, range 62

1. Introduction 4
Table of contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Main constructional features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Performance range 5
Performance range overview, S pumps. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Performance range, S pumps, range 62 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
List of pump curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

3. Identification 7
Type key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pump nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Ex approval plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cable entry approval plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4. Selection of product 9
Ordering the product . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5. Product range 10
Standard pumps - cast iron, 3 x 400/690 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Explosion-proof pumps - cast iron, 3 x 400/690 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

6. Variants 17
List of variants . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

7. Construction 18
Sectional drawings, motors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Components and material specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

8. Product description 26
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Motor range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Explosion-proof pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Level controllers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

9. Curve charts and technical data 34


How to read the curve charts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Curve conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Pump performance testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Performance-test types for end-suction pumps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Specifying acceptance grades . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Witness test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

10. Performance curves and technical data 40


Super-low pressure - 3 x 400/690 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Super-low pressure - 3 x 415 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Extra-low pressure - 3 x 400/690 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Extra-low pressure - 3 x 415 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Extra-low pressure - 3 x 400/690 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Extra-low pressure - 3 x 415 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Low pressure - 3 x 400/690 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Low pressure - 3 x 415 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Medium pressure - 3 x 400/690 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Medium pressure - 3 x 415 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
High pressure - 3 x 400/690 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
High pressure - 3 x 415 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

11. Accessories 64
Accessories (for installation) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Other accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

2
S pumps, range 62

12. Dimensions 67

Table of contents
Recommendation for pump foundations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Basic pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Installation on auto-coupling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Dry, vertical installation on base stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73

13. Weights 76

14. Flange forces 77

15. Grundfos Product Center 78

3
1 S pumps, range 62

1. Introduction
Introduction

Introduction Applications
This data booklet deals with Grundfos heavy-duty S pumps are designed for applications such as these:
sewage pumps type S, range 62. • raw-water intake
• wastewater treatment plants
• municipal pumping stations
• public buildings
• blocks of flats
• industries
• garages
• underground car parks
• car-wash areas
• restaurants and hotels.
The pumps are suitable for both temporary and
permanent installation. The lifting bracket fitted on the
pumps facilitates easy transportation as well as
installation at the installation site.
TM07 0218 4517

Main constructional features


• Leak-proof connections via the Grundfos SmartSeal
sealing system
• double mechanical shaft seal system for reliable
Fig. 1 S pump, range 62 sealing between pumped liquid and motor
S pumps, range 62, are a range of channel impeller • watertight cable entry
pumps specifically designed for pumping sewage and • moisture switch for continuous monitoring of motor
wastewater in a wide range of municipal, private and housing and terminal box ensuring automatic cut-off
industrial applications. of power in case of ingress of liquid
The pumps are made of resistant materials, such as • self-cleaning channel impeller with long vanes
cast iron and stainless steel. These materials ensure a reducing the risk of jamming or clogging
proper operation. • SmartTrim system allowing easy adjustment of
The pumps are fitted with motors from 15 to 50 kW. impeller clearance and maintaining maximum pump
The motors are either 4-, 8- or 12-pole motors, efficiency over pump lifetime
depending on the motor size. • motor in insulation class F (155 °C), enclosure class
The free passage in the pumps is 80 to 145 mm. IP68 with three thermal sensors in stator windings
The pumps are available for these types of installation: • shaft seal condition monitoring via water-in-oil
• submerged installation on auto-coupling system sensor (optional)
• submerged installation, free-standing • explosion-proof motors for applications involving
• dry installation, vertical potential risk of explosion
• dry installation, horizontal. • three stainless steel versions for use in corrosive or
aggressive liquids:
– stainless steel impeller, cast iron pump and motor
housing
– stainless steel pump housing, flange and impeller,
cast iron motor housing made entirely of
corrosion-resistant stainless steel.

4
S pumps, range 62
2

2. Performance range

Performance range
Performance range overview, S pumps

+
>P@
 +]





 

 















TM03 5469 3712


                   
4>OV@

           4>PñK@

5
2 S pumps, range 62

Performance range, S pumps, range 62


Performance range

H
[m]
80 S Pumps
Range 62
60 50 Hz
50

40
S1.80.125 S1.100.125
30
S2.100.200
25

20

15

S2.100.300
10
S2.145.300
8

6
S3.120.300
5

TM04 1876 1308


0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 360 380 400
Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Q [m³/h]

List of pump curves


3 x 400/690 V 3 x 415 V
Curve chart on Curve chart on
Pump type Pressure range Pump type Pressure range
page page
S3.120.300.xxx.12.62F Super low 40 S3.120.300.xxx.12.62F Super low 42
S2.145.300.xxx.8.62E 44 S2.145.300.xxx.8.62E 46
Extra low Extra low
S2.100.300.xxx.4.62E 48 S2.100.300.xxx.4.62E 50
S2.100.200.xxx.4.62L Low 52 S2.100.200.xxx.4.62L Low 54
S1.100.125.xxx.4.62M Medium 56 S1.100.125.xxx.4.62M Medium 54
S1.80.125.xxx.4.82H High 60 S1.80.125.xxx.4.82H High 62

6
S pumps, range 62
3

3. Identification

Identification
Type key 1
The power output (P2) indicated in the type key, which is used to
indicate the motor size, can deviate from the actual power output.
Please note that the pump type described in this Please refer to the nameplate or the chapter Performance curves
and technical data for the exact power output
booklet is not necessarily available in all variants. 2 PTC sensor are connected directly to IO 113 or other PTC relay.
Example: S1.100.100.55.4.50M.S.205.G.N.D.511.Z
Code Explanation Designation Pump nameplate
Grundfos sewage and wastewater
S
pump 1
Pump type
Multi-channel impeller pump installed
ST
in a column pipe 2 23
1 Single-channel impeller
3 12
2 Two-channel impeller
Impeller type
3 Three-channel impeller 4 13
V SuperVortex impeller 14
100 Maximum solid size [mm] Pump passage 5
15
Nominal diameter of pump outlet port Pump outlet, 6
[mm] S-type 16
100
Nominal diameter of column pipe Pump outlet, 7 17
[mm] ST-type
8 18
P2 = Code number from type
55 Power output [kW] 1

TM06 0370 5313


designation / 10 19
9
2 2-pole motor 20
4 4-pole motor 10
21
6 6-pole motor
Number of poles 11 22
8 8-pole motor
10 10-pole motor Fig. 2 Pump nameplate
12 12-pole motor
50 Range 50
Pos. Description
54 Range 54
58 Range 58 1 Type designation
Pump range
62 Range 62 2 Product number
66 Range 66 3 Serial number
70 Range 70 4 Maximum head
S Super-high 5 Maximum installation depth
H High 6 Number of phases
M Medium
Pressure version 7 Voltage, delta connection
L Low
8 Voltage, star connection
E Extra-low
9 Rated power input, P1
F Super-low
Submersible installation without 10 Cos φ, 1/1 load
S
cooling jacket 11 Production code, year and week
Submersible installation with cooling 12 Generation code
C Installation type
jacket
13 Maximum ambient temperature
D Dry installation, vertical
14 Maximum flow rate
H Dry installation, horizontal
15 Enclosure class
Impeller diameter
205 Impeller diameter [mm] 16 Frequency
(mean)
Cast-iron impeller, pump housing and 17 Rated speed
G
stator housing 18 Current, delta connection
Stainless-steel impeller, DIN W.-Nr. Material code for
Q 19 Current, star connection
1.4408 impeller, pump
Stainless-steel impeller and pump housing and stator 20 Rated power output, P2
S housing
housing, DIN W.-Nr. 1.4408 21 Insulation class
Stainless steel-impeller, pump housing 22 Net weight
R
and stator housing, DIN W.-Nr. 1.4408
23 Place of production
N Non-explosion-proof pump
Pump version
Ex Pump with explosion-proof motor
B S pump with built-in SM 113 2
C Not in use Sensor version
D S pump without built-in SM 113
5 50 Hz
Frequency [Hz]
6 60 Hz
3 x 400 / 690 V, Y/D (50 Hz only)
11
3 x 460 V, Y/D (60 Hz only) Voltage code and
13 3 x 415 V, Y/D (50 Hz only) connection
15 3 x 380 / 660 V, Y/D (60 Hz only)
GPA Pumps only for Australia
Customisation
Z Custom-built products

7
3 S pumps, range 62

Ex approval plate Cable entry approval plate


Identification

TM06 7260 1217


II2G
Baseefa17ATEX0013U
DK-8850 Bjerringbro, Denmark DK-8850 Bjerringbro, Denmark
0344

Made in H-8000 Székesfehérvár, Hungary

Made in H-8000 Székesfehérvár, Hungary


IECEx BAS 17.0007U
II2G 0344 II2G 0344 Ex db IIB Gb Tamb =-5°C–+80°C
ID no DK-8850
Ex b c IIB T3 Ex b c IIB T4
Baseefa 09ATEX0020X Baseefa 09ATEX0020X Fig. 4 Cable entry approval plate

TM06 7560 4617 - TM06 7561 4617


Ex db IIB T3 Gb Ex db IIB T4 Gb
IECEx BAS09.0006X IECEx BAS09.0006X The approval plate gives the following details:

Type Type Pos. Description

yyww/no yyww/no
CE CE-mark
Warnings: Warnings: 1180 Number of quality assurance notified body
Do not open when energized. Do not open when energized or when
Cable temperature may exceed 70ºC. explosive gas atmosphere is present.
Cable temperature may exceed 70°C.
EU ex-symbol
Cable gland size and installation:see
installation and operating instructions.
Cable gland size and installation:see
installation and operation manual.
II Equipment group (II = non-mining)
Tamb=-5°C–+40°C Tamb=-5°C–+40°C
98488084 98488082
2 Equipment category (high protection)
G Type of explosive atmosphere
Fig. 3 Approval plate of Ex pumps, T3 and T4 Ex Explosion-proof motor according to European standard
classification b Control of ignition sources
db Flameproof
The approval plate gives the following details:
IIB Gas group (Ethylene)
Pos. Description Tamb Ambient temperature

EU Ex symbol Gb Equipment protection level, zone 1


Baseefa Certificate number
II Equipment group (II = non-mining)
IECEx Certificate number
2 Equipment category (high protection)
ID no Inlet identification number (e.g. 36-1)
G Type of explosive atmosphere (G = Gas)
CE CE mark
0344 Number of quality assurance notified body
Ex Explosion-proof motor according to European standard
b Control of ignition sources
c Constructional safety
db Flameproof enclosure
IIB Gas group (Ethylene)
T3 Maximum surface temperature of the motor is 200 °C
T4 Maximum surface temperature of the motor is 135 °C
Gb Equipment protection level, zone 1
Baseefa Certificate number
IECEx Certificate number

8
S pumps, range 62
4

4. Selection of product

Selection of product
Ordering the product Accessories
When ordering the product, you need to take the Depending on the installation type, you may need to
following four aspects into consideration: order accessories. See Accessories, page 64 for
selection of the correct accessories.
1. pump
Note: Ordered accessories are not fitted from factory.
2. custom-built variation (option)
3. accessories Controller
4. controller.
Grundfos Dedicated Controls (DC) is available.
Pump
Use Product range starting on page 10 and Type key,
page 7 to identify the pump that best fulfils your needs.
The list below is a detailed description of the product
you get if you order the following pump:
Pump Product no
S1.80.125.300.4.62H.S.338.G.N.D 95113209
• Pump as specified in the type key
• 10 m cable
• Paint: black, NCS 9000N/RAL 9005, gloss 30,
thickness 150 µm
• Three thermal switches (Klixon) or three thermal
sensors (PTC) in stator windings
• One moisture switch below the motor top cover (two
moisture switches in explosion-proof versions: one

TM06 6501 1515


below the motor top cover and one in the stator
housing in the bottom of the motor)
• Test according to ISO 9906:2012, grade 3B.
See Performance curves and technical data, page 40 Fig. 5 Grundfos Dedicated Controls
for selection of a standard pump.
Note: Product-specific data for the pump can also be Grundfos Dedicated Controls is a control system
found in Grundfos Product Center using the product designed for installation in either commercial buildings
number 95113209. or network pumping stations with one to six pumps.
As standard, the system is supplied with application-
Custom-built variants optimised software and can be configured to meet your
The S pumps can be customised to meet individual specific pumping needs.
requirements. Many pump features and options are For more information about Grundfos Dedicated
available for customisation, e.g. explosion-proof Controls, see Level controllers, page 28.
versions, various cable lengths or special materials.
Variants can be seen in List of variants, page 17. For
requirements or designs not included in the list,
contact Grundfos.

9
5 S pumps, range 62

5. Product range
Product range

Standard pumps - cast iron, 3 x 400/690 V


Accessories

Cable length To be ordered separately


Pump type Pump Horizontal base
[m]
stand 1 Vertical base Auto-coupling
stand system 2
S1.80.125.300.4.62H.S.338.G.N.D... 10 95113209 - - 96782145
S1.80.125.300.4.62H.C.338.G.N.D... 10 95113210 - - 96782145
S1.80.125.300.4.62H.H.338.G.N.D... 10 95113211 96787496 - -
S1.80.125.300.4.62H.D.338.G.N.D... 10 95113644 - 96308238 -
S1.80.125.400.4.62H.S.374.G.N.D... 10 95113212 - - 96782145
S1.80.125.400.4.62H.C.374.G.N.D... 10 95113213 - - 96782145
S1.80.125.400.4.62H.H.374.G.N.D... 10 95113214 96787496 - -
S1.80.125.400.4.62H.D.374.G.N.D... 10 95113647 - 96308238 -
S1.80.125.500.4.62H.S.398.G.N.D... 10 95113215 - - 96782145
S1.80.125.500.4.62H.C.398.G.N.D... 10 95113216 - - 96782145
S1.80.125.500.4.62H.H.398.G.N.D... 10 95113217 96787496 - -
S1.80.125.500.4.62H.D.398.G.N.D... 10 95113650 - 96308238 -
S1.100.125.300.4.62M.S.314.G.N.D... 10 95113239 - - 96782145
S1.100.125.300.4.62M.C.314.G.N.D... 10 95113240 - - 96782145
S1.100.125.300.4.62M.H.314.G.N.D... 10 95113241 96787497 - -
S1.100.125.300.4.62M.D.314.G.N.D... 10 95113659 - 96094523 -
S1.100.125.400.4.62M.S.345.G.N.D... 10 95113242 - - 96782145
S1.100.125.400.4.62M.C.345.G.N.D... 10 95113243 - - 96782145
S1.100.125.400.4.62M.H.345.G.N.D... 10 95113244 96787497 - -
S1.100.125.400.4.62M.D.345.G.N.D... 10 96787705 - 96094523 -
S1.100.125.500.4.62M.S.367.G.N.D... 10 95113245 - - 96782145
S1.100.125.500.4.62M.C.367.G.N.D... 10 95113246 - - 96782145
S1.100.125.500.4.62M.H.367.G.N.D... 10 95113247 96787497 - -
S1.100.125.500.4.62M.D.367.G.N.D... 10 96787709 - 96094523 -
S2.100.200.400.4.62L.S.285.G.N.D... 10 95113224 - - 96641489
S2.100.200.400.4.62L.C.285.G.N.D... 10 95113225 - - 96641489
S2.100.200.400.4.62L.H.285.G.N.D... 10 95113226 96787498 - -
S2.100.200.400.4.62L.D.285.G.N.D... 10 95113653 - 96094525 -
S2.100.200.500.4.62L.S.290.G.N.D... 10 95113227 - - 96641489
S2.100.200.500.4.62L.C.290.G.N.D... 10 95113228 - - 96641489
S2.100.200.500.4.62L.H.290.G.N.D... 10 95113229 96787498 - -
S2.100.200.500.4.62L.D.290.G.N.D... 10 95113656 - 96094525 -
S2.100.300.300.4.62E.S.253.G.N.D... 10 95113230 - - 96782484
S2.100.300.300.4.62E.C.253.G.N.D... 10 95113231 - - 96782484
S2.100.300.300.4.62E.D.253.G.N.D... 10 95113232 - 96094525 -
S2.100.300.300.4.62E.H.253.G.N.D... 10 96783255 96787499 - -
S2.100.300.400.4.62E.S.281.G.N.D... 10 95113233 - - 96782484
S2.100.300.400.4.62E.C.281.G.N.D... 10 95113234 - - 96782484
S2.100.300.400.4.62E.D.281.G.N.D... 10 95113235 - 96094525 -
S2.100.300.400.4.62E.H.281.G.N.D... 10 96783260 96787499 - -
S2.100.300.500.4.62E.S.289.G.N.D... 10 95113236 - - 96782484
S2.100.300.500.4.62E.C.289.G.N.D... 10 95113237 - - 96782484
S2.100.300.500.4.62E.D.289.G.N.D... 10 95113238 - 96094525 -
S2.100.300.500.4.62E.H.289.G.N.D... 10 96783265 96787499 - -
S2.145.300.200.8.62E.S.388.G.N.D... 10 95113218 - - 96782484
S2.145.300.200.8.62E.C.388.G.N.D... 10 95113219 - - 96782484
S2.145.300.200.8.62E.D.388.G.N.D... 10 95113220 - 96308239 -
S2.145.300.200.8.62E.H.388.G.N.D... 10 96783239 96787500 - -
S2.145.300.280.8.62E.S.421.G.N.D... 10 95113221 - - 96782484
S2.145.300.280.8.62E.C.421.G.N.D... 10 95113222 - - 96782484
S2.145.300.280.8.62E.D.421.G.N.D... 10 95113223 - 96308239 -
S2.145.300.280.8.62E.H.421.G.N.D... 10 96783244 96787500 - -
S3.120.300.150.12.62F.S.449.G.N.D... 10 95113248 - - 96782484
S3.120.300.150.12.62F.C.449.G.N.D... 10 95113249 - - 96782484
S3.120.300.150.12.62F.D.449.G.N.D... 10 95113250 - 96308239 -
S3.120.300.150.12.62F.H.449.G.N.D... 10 96783279 96787500 - -
1
Pumps of installation type H include the standard horizontal stand. Pumps with material code G or Q include a painted-steel stand. If another
horizontal stand is required, order a pump of installation type D together with the required stand.
2 Installation type S and C pumps with outlet flange size DN 250 and higher are supplied with a guide claw mounted on the flange.

10
S pumps, range 62
5
Cast iron, 3 x 415 V

Product range
Accessories

Cable length To be ordered separately


Pump type Pump Horizontal base
[m]
stand 1 Vertical base Auto-coupling
stand system 2
S1.80.125.300.4.62H.D.338.G.N.D... 10 96781861 - 96308238 -
S1.80.125.300.4.62H.S.338.G.N.D... 10 96783227 - - 96782145
S1.80.125.300.4.62H.C.338.G.N.D... 10 96783228 - - 96782145
S1.80.125.300.4.62H.H.338.G.N.D... 10 96783229 96787496 - -
S1.80.125.400.4.62H.S.374.G.N.D... 10 96783230 - - 96782145
S1.80.125.400.4.62H.D.374.G.N.D... 10 96781864 - 96308238 -
S1.80.125.400.4.62H.C.374.G.N.D... 10 96783231 - - 96782145
S1.80.125.400.4.62H.H.374.G.N.D... 10 96783232 96787496 - -
S1.80.125.500.4.62H.D.398.G.N.D... 10 96781867 - 96308238 -
S1.80.125.500.4.62H.S.398.G.N.D... 10 96783233 - - 96782145
S1.80.125.500.4.62H.C.398.G.N.D... 10 96783234 - - 96782145
S1.80.125.500.4.62H.H.398.G.N.D... 10 96783235 96787496 - -
S1.100.125.300.4.62M.D.314.G.N.D... 10 96781876 - 96094523 -
S1.100.125.300.4.62M.S.314.G.N.D... 10 96783267 - - 96782145
S1.100.125.300.4.62M.C.314.G.N.D... 10 96783268 - - 96782145
S1.100.125.300.4.62M.H.314.G.N.D... 10 96783269 96787497 - -
S1.100.125.400.4.62M.S.345.G.N.D... 10 96783270 - - 96782145
S1.100.125.400.4.62M.C.345.G.N.D... 10 96783271 - - 96782145
S1.100.125.400.4.62M.H.345.G.N.D... 10 96783272 96787497 - -
S1.100.125.400.4.62M.D.345.G.N.D... 10 96787707 - 96094523 -
S1.100.125.500.4.62M.S.367.G.N.D... 10 96783273 - - 96782145
S1.100.125.500.4.62M.C.367.G.N.D... 10 96783274 - - 96782145
S1.100.125.500.4.62M.H.367.G.N.D... 10 96783275 96787497 - -
S1.100.125.500.4.62M.D.367.G.N.D... 10 96787710 - 96094523 -
S2.100.200.400.4.62L.S.285.G.N.D... 10 96783246 - - 96641489
S2.100.200.400.4.62L.D.285.G.N.D... 10 96781870 - 96094525
S2.100.200.400.4.62L.C.285.G.N.D... 10 96783247 - - 96641489
S2.100.200.400.4.62L.H.285.G.N.D... 10 96783248 96787498 - -
S2.100.200.500.4.62L.D.290.G.N.D... 10 96781873 - 96094525 -
S2.100.200.500.4.62L.S.290.G.N.D... 10 96783249 - - 96641489
S2.100.200.500.4.62L.C.290.G.N.D... 10 96783250 - - 96641489
S2.100.200.500.4.62L.H.290.G.N.D... 10 96783251 96787498 - -
S2.100.300.300.4.62E.S.253.G.N.D... 10 96783252 - - 96782484
S2.100.300.300.4.62E.C.253.G.N.D... 10 96783253 - - 96782484
S2.100.300.300.4.62E.D.253.G.N.D... 10 96783254 - 96094525 -
S2.100.300.300.4.62E.H.253.G.N.D... 10 96783256 96787499 - -
S2.100.300.400.4.62E.S.281.G.N.D... 10 96783257 - - 96782484
S2.100.300.400.4.62E.C.281.G.N.D... 10 96783258 - - 96782484
S2.100.300.400.4.62E.D.281.G.N.D... 10 96783259 - 96094525 -
S2.100.300.400.4.62E.H.281.G.N.D... 10 96783261 96787499 - -
S2.100.300.500.4.62E.S.289.G.N.D... 10 96783262 - - 96782484
S2.100.300.500.4.62E.C.289.G.N.D... 10 96783263 - - 96782484
S2.100.300.500.4.62E.D.289.G.N.D... 10 96783264 - 96094525 -
S2.100.300.500.4.62E.H.289.G.N.D... 10 96783266 96787499 - -
S2.145.300.200.8.62E.S.388.G.N.D... 10 96783236 - - 96782484
S2.145.300.200.8.62E.C.388.G.N.D... 10 96783237 - - 96782484
S2.145.300.200.8.62E.D.388.G.N.D... 10 96783238 - 96308239 -
S2.145.300.200.8.62E.H.388.G.N.D... 10 96783240 96787500 - -
S2.145.300.280.8.62E.S.421.G.N.D... 10 96783241 - - 96782484
S2.145.300.280.8.62E.C.421.G.N.D... 10 96783242 - - 96782484
S2.145.300.280.8.62E.D.421.G.N.D... 10 96783243 - 96308239 -
S2.145.300.280.8.62E.H.421.G.N.D... 10 96783245 96787500 - -
S3.120.300.150.12.62F.S.449.G.N.D... 10 96783276 - - 96782484
S3.120.300.150.12.62F.C.449.G.N.D... 10 96783277 - - 96782484
S3.120.300.150.12.62F.D.449.G.N.D... 10 96783278 - 96308239 -
S3.120.300.150.12.62F.H.449.G.N.D... 10 96783280 96787500 - -
1
Pumps of installation type H include the standard horizontal stand. Pumps with material code G or Q include a painted-steel stand. If another
horizontal stand is required, order a pump of installation type D together with the required stand.
2 Installation type S and C pumps with outlet flange size DN 250 and higher are supplied with a guide claw mounted on the flange.

11
5 S pumps, range 62

Cast iron, 3 x 415 V - Australia


Product range

Note: Pumps with 15 m cable are installed with PTC thermal protection.
Accessories

Cable length To be ordered separately


Pump type Pump Horizontal base
[m]
stand 1 Vertical base Auto-coupling
stand system 2
S1.80.125.300.4.62H.S.338.G.N.D... 15 96810422 - - 96782145
S1.80.125.300.4.62H.C.338.G.N.D... 15 96810423 - - 96782145
S1.80.125.300.4.62H.D.338.G.N.D... 15 96810424 - 96308238 -
S1.80.125.300.4.62H.H.338.G.N.D... 15 96810425 96787496 - -
S1.80.125.400.4.62H.S.374.G.N.D... 15 96810426 - - 96782145
S1.80.125.400.4.62H.C.374.G.N.D... 15 96810427 - - 96782145
S1.80.125.400.4.62H.D.374.G.N.D... 15 96810428 - 96308238 -
S1.80.125.400.4.62H.H.374.G.N.D... 15 96810429 96787496 - -
S1.80.125.500.4.62H.S.398.G.N.D... 15 96810430 - - 96782145
S1.80.125.500.4.62H.C.398.G.N.D... 15 96810431 - - 96782145
S1.80.125.500.4.62H.D.398.G.N.D... 15 96810432 - 96308238 -
S1.80.125.500.4.62H.H.398.G.N.D... 15 96810433 96787496 - -
S1.100.125.300.4.62M.S.314.G.N.D... 15 96810462 - - 96782145
S1.100.125.300.4.62M.C.314.G.N.D... 15 96810463 - - 96782145
S1.100.125.300.4.62M.D.314.G.N.D... 15 96810465 - 96094523 -
S1.100.125.300.4.62M.H.314.G.N.D... 15 96810466 96787497 - -
S1.100.125.400.4.62M.S.345.G.N.D... 15 96810467 - - 96782145
S1.100.125.400.4.62M.C.345.G.N.D... 15 96810468 - - 96782145
S1.100.125.400.4.62M.D.345.G.N.D... 15 96810469 - 96094523 -
S1.100.125.400.4.62M.H.345.G.N.D... 15 96810470 96787497 - -
S1.100.125.500.4.62M.S.367.G.N.D... 15 96810471 - - 96782145
S1.100.125.500.4.62M.C.367.G.N.D... 15 96810472 - - 96782145
S1.100.125.500.4.62M.D.367.G.N.D... 15 96810473 - 96094523 -
S1.100.125.500.4.62M.H.367.G.N.D... 15 96810474 96787497 - -
S2.100.200.400.4.62L.S.285.G.N.D... 15 96810442 - - 96641489
S2.100.200.400.4.62L.C.285.G.N.D... 15 96810443 - - 96641489
S2.100.200.400.4.62L.D.285.G.N.D... 15 96810444 - 96094525 -
S2.100.200.400.4.62L.H.285.G.N.D... 15 96810445 96787498 - -
S2.100.200.500.4.62L.S.290.G.N.D... 15 96810446 - - 96641489
S2.100.200.500.4.62L.C.290.G.N.D... 15 96810447 - - 96641489
S2.100.200.500.4.62L.D.290.G.N.D... 15 96810448 - 96094525 -
S2.100.200.500.4.62L.H.290.G.N.D... 15 96810449 96787498 - -
S2.100.300.300.4.62E.S.253.G.N.D... 15 96810450 - - 96782484
S2.100.300.300.4.62E.C.253.G.N.D... 15 96810451 - - 96782484
S2.100.300.300.4.62E.D.253.G.N.D... 15 96810452 - 96094525 -
S2.100.300.300.4.62E.H.253.G.N.D... 15 96810453 96787499 - -
S2.100.300.400.4.62E.S.281.G.N.D... 15 96810454 - - 96782484
S2.100.300.400.4.62E.C.281.G.N.D... 15 96810455 - - 96782484
S2.100.300.400.4.62E.D.281.G.N.D... 15 96810456 - 96094525 -
S2.100.300.400.4.62E.H.281.G.N.D... 15 96810457 96787499 - -
S2.100.300.500.4.62E.S.289.G.N.D... 15 96810458 - - 96782484
S2.100.300.500.4.62E.C.289.G.N.D... 15 96810459 - - 96782484
S2.100.300.500.4.62E.D.289.G.N.D... 15 96810460 - 96094525 -
S2.100.300.500.4.62E.H.289.G.N.D... 15 96810461 96787499 - -
S2.145.300.200.8.62E.S.388.G.N.D... 15 96810434 - - 96782484
S2.145.300.200.8.62E.C.388.G.N.D... 15 96810435 - - 96782484
S2.145.300.200.8.62E.D.388.G.N.D... 15 96810436 - 96308239 -
S2.145.300.200.8.62E.H.388.G.N.D... 15 96810437 96787500 - -
S2.145.300.280.8.62E.S.421.G.N.D... 15 96810438 - - 96782484
S2.145.300.280.8.62E.C.421.G.N.D... 15 96810439 - - 96782484
S2.145.300.280.8.62E.D.421.G.N.D... 15 96810440 - 96308239 -
S2.145.300.280.8.62E.H.421.G.N.D... 15 96810441 96787500 - -
S3.120.300.150.12.62F.S.449.G.N.D... 15 96810475 - - 96782484
S3.120.300.150.12.62F.C.449.G.N.D... 15 96810476 - - 96782484
S3.120.300.150.12.62F.D.449.G.N.D... 15 96810477 - 96308239 -
S3.120.300.150.12.62F.H.449.G.N.D... 15 96810478 96787500 - -

1 Pumps of installation type H include the standard horizontal stand. Pumps with material code G or Q include a painted-steel stand. If another
horizontal stand is required, order a pump of installation type D together with the required stand.
2
Installation type S and C pumps with outlet flange size DN 250 and higher are supplied with a guide claw mounted on the flange.

12
S pumps, range 62
5
Stainless steel impeller, 3 x 400/690 V

Product range
Accessories

Cable length To be ordered separately


Pump type Pump Horizontal base
[m]
stand 1 Vertical base Auto-coupling
stand system 2
S1.80.125.300.4.62H.S.338.Q.N.D... 10 96811580 - - 96782145
S1.80.125.300.4.62H.C.338.Q.N.D... 10 96811581 - - 96782145
S1.80.125.300.4.62H.D.338.Q.N.D... 10 96811592 - 96308238 -
S1.80.125.300.4.62H.H.338.Q.N.D... 10 96811593 96787496 - -
S1.80.125.400.4.62H.S.374.Q.N.D... 10 96811594 - - 96782145
S1.80.125.400.4.62H.C.374.Q.N.D... 10 96811595 - - 96782145
S1.80.125.400.4.62H.D.374.Q.N.D... 10 96811596 - 96308238 -
S1.80.125.400.4.62H.H.374.Q.N.D... 10 96811597 96787496 - -
S1.80.125.500.4.62H.S.398.Q.N.D... 10 96811598 - - 96782145
S1.80.125.500.4.62H.C.398.Q.N.D... 10 96811599 - - 96782145
S1.80.125.500.4.62H.D.398.Q.N.D... 10 96811600 - 96308238 -
S1.80.125.500.4.62H.H.398.Q.N.D... 10 96811601 96787496 - -
S1.100.125.300.4.62M.S.314.Q.N.D... 10 96811625 - - 96782145
S1.100.125.300.4.62M.C.314.Q.N.D... 10 96811626 - - 96782145
S1.100.125.300.4.62M.D.314.Q.N.D... 10 96811627 - 96094523 -
S1.100.125.300.4.62M.H.314.Q.N.D... 10 96811628 96787497 - -
S1.100.125.400.4.62M.S.345.Q.N.D... 10 96811629 - - 96782145
S1.100.125.400.4.62M.C.345.Q.N.D... 10 96811630 - - 96782145
S1.100.125.400.4.62M.D.345.Q.N.D... 10 96811631 - 96094523 -
S1.100.125.400.4.62M.H.345.Q.N.D... 10 96811632 96787497 - -
S1.100.125.500.4.62M.S.367.Q.N.D... 10 96811633 - - 96782145
S1.100.125.500.4.62M.C.367.Q.N.D... 10 96811634 - - 96782145
S1.100.125.500.4.62M.D.367.Q.N.D... 10 96811635 - 96094523 -
S1.100.125.500.4.62M.H.367.Q.N.D... 10 96811636 96787497 - -
S2.100.200.400.4.62L.S.285.Q.N.D... 10 96811608 - - 96641489
S2.100.200.400.4.62L.C.285.Q.N.D... 10 96811609 - - 96641489
S2.100.200.400.4.62L.D.285.Q.N.D... 10 96811610 - 96094525 -
S2.100.200.400.4.62L.H.285.Q.N.D... 10 96811611 96787498 - -
S2.100.200.500.4.62L.S.290.Q.N.D... 10 96811612 - - 96641489
S2.100.200.500.4.62L.C.290.Q.N.D... 10 96811613 - - 96641489
S2.100.200.500.4.62L.D.290.Q.N.D... 10 96811614 - 96094525 -
S2.100.200.500.4.62L.H.290.Q.N.D... 10 96811615 96787498 - -
S2.100.300.300.4.62E.S.253.Q.N.D... 10 96811616 - - 96782484
S2.100.300.300.4.62E.C.253.Q.N.D... 10 96811617 - - 96782484
S2.100.300.300.4.62E.D.253.Q.N.D... 10 96811618 - 96094525 -
S2.100.300.300.4.62E.H.253.Q.N.D... 10 96811642 96787499 - -
S2.100.300.400.4.62E.S.281.Q.N.D... 10 96811619 - - 96782484
S2.100.300.400.4.62E.C.281.Q.N.D... 10 96811620 - - 96782484
S2.100.300.400.4.62E.D.281.Q.N.D... 10 96811621 - 96094525 -
S2.100.300.400.4.62E.H.281.Q.N.D... 10 96811643 96787499 - -
S2.100.300.500.4.62E.S.289.Q.N.D... 10 96811622 - - 96782484
S2.100.300.500.4.62E.C.289.Q.N.D... 10 96811623 - - 96782484
S2.100.300.500.4.62E.D.289.Q.N.D... 10 96811624 - 96094525 -
S2.100.300.500.4.62E.H.289.Q.N.D... 10 96811644 96787499 - -
S2.145.300.200.8.62E.S.388.Q.N.D... 10 96811602 - - 96782484
S2.145.300.200.8.62E.C.388.Q.N.D... 10 96811603 - - 96782484
S2.145.300.200.8.62E.D.388.Q.N.D... 10 96811604 - 96308239 -
S2.145.300.200.8.62E.H.388.Q.N.D... 10 96811640 96787500 - -
S2.145.300.280.8.62E.S.421.Q.N.D... 10 96811605 - - 96782484
S2.145.300.280.8.62E.C.421.Q.N.D... 10 96811606 - - 96782484
S2.145.300.280.8.62E.D.421.Q.N.D... 10 96811607 - 96308239 -
S2.145.300.280.8.62E.H.421.Q.N.D... 10 96811641 96787500 - -
S3.120.300.150.12.62F.S.449.Q.N.D... 10 96811637 - - 96782484
S3.120.300.150.12.62F.C.449.Q.N.D... 10 96811638 - - 96782484
S3.120.300.150.12.62F.D.449.Q.N.D... 10 96811639 - 96308239 -
S3.120.300.150.12.62F.H.449.Q.N.D... 10 96811645 96787500 - -
1
Pumps of installation type H include the standard horizontal stand. Pumps with material code G or Q include a painted-steel stand. If another
horizontal stand is required, order a pump of installation type D together with the required stand.
2 Installation type S and C pumps with outlet flange size DN 250 and higher are supplied with a guide claw mounted on the flange.

13
5 S pumps, range 62

Explosion-proof pumps - cast iron, 3 x 400/690 V


Product range

Accessories

Cable length To be ordered separately


Pump type Pump Horizontal base
[m]
stand 1 Vertical base Auto-coupling
stand system 2
S1.80.125.300.4.62H.S.338.G.EX.D... 10 95113260 - - 96782145
S1.80.125.300.4.62H.C.338.G.EX.D... 10 95113261 - - 96782145
S1.80.125.300.4.62H.H.338.G.EX.D... 10 95113262 96787496 - -
S1.80.125.300.4.62H.D.338.G.EX.D... 10 96788055 - 96308238 -
S1.80.125.400.4.62H.S.374.G.EX.D... 10 95113266 - - 96782145
S1.80.125.400.4.62H.C.374.G.EX.D... 10 95113267 - - 96782145
S1.80.125.400.4.62H.H.374.G.EX.D... 10 95113268 96787496 - -
S1.80.125.400.4.62H.D.374.G.EX.D... 10 96788057 - 96308238 -
S1.80.125.500.4.62H.S.398.G.EX.D... 10 95113272 - - 96782145
S1.80.125.500.4.62H.C.398.G.EX.D... 10 95113273 - - 96782145
S1.80.125.500.4.62H.H.398.G.EX.D... 10 95113274 96787496 - -
S1.80.125.500.4.62H.D.398.G.EX.D... 10 96788059 - 96308238 -
S1.100.125.300.4.62M.S.314.G.EX.D... 10 95113263 - - 96782145
S1.100.125.300.4.62M.C.314.G.EX.D... 10 95113264 - - 96782145
S1.100.125.300.4.62M.H.314.G.EX.D... 10 95113265 96787497 - -
S1.100.125.300.4.62M.D.314.G.EX.D... 10 96788056 - 96094523 -
S1.100.125.400.4.62M.S.345.G.EX.D... 10 95113269 - - 96782145
S1.100.125.400.4.62M.C.345.G.EX.D... 10 95113270 - - 96782145
S1.100.125.400.4.62M.H.345.G.EX.D... 10 95113271 96787497 - -
S1.100.125.400.4.62M.D.345.G.EX.D... 10 96788058 - 96094523 -
S1.100.125.500.4.62M.S.367.G.EX.D... 10 95113275 - - 96782145
S1.100.125.500.4.62M.C.367.G.EX.D... 10 95113276 - - 96782145
S1.100.125.500.4.62M.H.367.G.EX.D... 10 95113277 96787497 - -
S1.100.125.500.4.62M.D.367.G.EX.D... 10 96788060 - 96094523 -
S2.100.200.400.4.62L.S.285.G.EX.D... 10 95113287 - - 96641489
S2.100.200.400.4.62L.C.285.G.EX.D... 10 95113288 - - 96641489
S2.100.200.400.4.62L.H.285.G.EX.D... 10 95113289 96787498 - -
S2.100.200.400.4.62L.D.285.G.EX.D... 10 96788061 - 96094525 -
S2.100.200.500.4.62L.S.290.G.EX.D... 10 95113293 - - 96641489
S2.100.200.500.4.62L.C.290.G.EX.D... 10 95113294 - - 96641489
S2.100.200.500.4.62L.H.290.G.EX.D... 10 95113295 96787498 - -
S2.100.200.500.4.62L.D.290.G.EX.D... 10 96788072 - 96094525 -
S2.100.300.300.4.62E.S.253.G.EX.D... 10 95113284 - - 96782484
S2.100.300.300.4.62E.C.253.G.EX.D... 10 95113285 - - 96782484
S2.100.300.300.4.62E.D.253.G.EX.D... 10 95113286 - 96094525 -
S2.100.300.300.4.62E.H.253.G.EX.D... 10 96784050 96787499 - -
S2.100.300.400.4.62E.S.281.G.EX.D... 10 95113290 - - 96782484
S2.100.300.400.4.62E.C.281.G.EX.D... 10 95113291 - - 96782484
S2.100.300.400.4.62E.D.281.G.EX.D... 10 95113292 - 96094525 -
S2.100.300.400.4.62E.H.281.G.EX.D... 10 96784058 96787499 - -
S2.100.300.500.4.62E.S.289.G.EX.D... 10 95113296 - - 96782484
S2.100.300.500.4.62E.C.289.G.EX.D... 10 95113297 - - 96782484
S2.100.300.500.4.62E.D.289.G.EX.D... 10 95113298 - 96094525 -
S2.100.300.500.4.62E.H.289.G.EX.D... 10 96784066 96787499 - -
S2.145.300.200.8.62E.S.388.G.EX.D... 10 95113278 - - 96782484
S2.145.300.200.8.62E.C.388.G.EX.D... 10 95113279 - - 96782484
S2.145.300.200.8.62E.D.388.G.EX.D... 10 95113280 - 96308239 -
S2.145.300.200.8.62E.H.388.G.EX.D... 10 96784040 96787500 - -
S2.145.300.280.8.62E.S.421.G.EX.D... 10 95113281 - - 96782484
S2.145.300.280.8.62E.C.421.G.EX.D... 10 95113282 - - 96782484
S2.145.300.280.8.62E.D.421.G.EX.D... 10 95113283 - 96308239 -
S2.145.300.280.8.62E.H.421.G.EX.D... 10 96784045 96787500 - -
S3.120.300.150.12.62F.S.449.G.EX.D... 10 95113299 - - 96782484
S3.120.300.150.12.62F.C.449.G.EX.D... 10 95113300 - - 96782484
S3.120.300.150.12.62F.D.449.G.EX.D... 10 95113301 - 96308239 -
S3.120.300.150.12.62F.H.449.G.EX.D... 10 96784071 96787500 - -
1
Pumps of installation type H include the standard horizontal stand. Pumps with material code G or Q include a painted-steel stand. If another
horizontal stand is required, order a pump of installation type D together with the required stand.
2 Installation type S and C pumps with outlet flange size DN 250 and higher are supplied with a guide claw mounted on the flange.

14
S pumps, range 62
5
Cast iron, 3 x 415 V

Product range
Accessories

Cable length To be ordered separately


Pump type Pump Horizontal base
[m]
stand 1 Vertical base Auto-coupling
stand system 2
S1.80.125.300.4.62H.S.338.G.EX.D... 10 96783979 - - 96782145
S1.80.125.300.4.62H.C.338.G.EX.D... 10 96783980 - - 96782145
S1.80.125.300.4.62H.H.338.G.EX.D... 10 96783981 96787496 - -
S1.80.125.300.4.62H.D.338.G.EX.D... 10 96788073 - 96308238 -
S1.80.125.400.4.62H.S.374.G.EX.D... 10 96784025 - - 96782145
S1.80.125.400.4.62H.C.374.G.EX.D... 10 96784026 - - 96782145
S1.80.125.400.4.62H.H.374.G.EX.D... 10 96784027 96787496 - -
S1.80.125.400.4.62H.D.374.G.EX.D... 10 96788075 - 96308238 -
S1.80.125.500.4.62H.S.398.G.EX.D... 10 96784031 - - 96782145
S1.80.125.500.4.62H.C.398.G.EX.D... 10 96784032 - - 96782145
S1.80.125.500.4.62H.H.398.G.EX.D... 10 96784033 96787496 - -
S1.80.125.500.4.62H.D.398.G.EX.D... 10 96788077 - 96308238 -
S1.100.125.300.4.62M.S.314.G.EX.D... 10 96784022 - - 96782145
S1.100.125.300.4.62M.C.314.G.EX.D... 10 96784023 - - 96782145
S1.100.125.300.4.62M.H.314.G.EX.D... 10 96784024 96787497 - -
S1.100.125.300.4.62M.D.314.G.EX.D... 10 96788074 - 96094523 -
S1.100.125.400.4.62M.S.345.G.EX.D... 10 96784028 - - 96782145
S1.100.125.400.4.62M.C.345.G.EX.D... 10 96784029 - - 96782145
S1.100.125.400.4.62M.H.345.G.EX.D... 10 96784030 96787497 - -
S1.100.125.400.4.62M.D.345.G.EX.D... 10 96788076 - 96094523 -
S1.100.125.500.4.62M.S.367.G.EX.D... 10 96784034 - - 96782145
S1.100.125.500.4.62M.C.367.G.EX.D... 10 96784035 - - 96782145
S1.100.125.500.4.62M.H.367.G.EX.D... 10 96784036 96787497 - -
S1.100.125.500.4.62M.D.367.G.EX.D... 10 96788078 - 96094523 -
S2.100.200.400.4.62L.S.285.G.EX.D... 10 96784052 - - 96641489
S2.100.200.400.4.62L.C.285.G.EX.D... 10 96784053 - - 96641489
S2.100.200.400.4.62L.H.285.G.EX.D... 10 96784054 96787498 - -
S2.100.200.400.4.62L.D.285.G.EX.D... 10 96788079 - 96094525 -
S2.100.200.500.4.62L.S.290.G.EX.D... 10 96784060 - - 96641489
S2.100.200.500.4.62L.C.290.G.EX.D... 10 96784061 - - 96641489
S2.100.200.500.4.62L.H.290.G.EX.D... 10 96784062 96787498 - -
S2.100.200.500.4.62L.D.290.G.EX.D... 10 96788080 - 96094525 -
S2.100.300.300.4.62E.S.253.G.EX.D... 10 96784047 - - 96782484
S2.100.300.300.4.62E.C.253.G.EX.D... 10 96784048 - - 96782484
S2.100.300.300.4.62E.D.253.G.EX.D... 10 96784049 - 96094525 -
S2.100.300.300.4.62E.H.253.G.EX.D... 10 96784051 96787499 - -
S2.100.300.400.4.62E.S.281.G.EX.D... 10 96784055 - - 96782484
S2.100.300.400.4.62E.C.281.G.EX.D... 10 96784056 - - 96782484
S2.100.300.400.4.62E.D.281.G.EX.D... 10 96784057 - 96094525 -
S2.100.300.400.4.62E.H.281.G.EX.D... 10 96784059 96787499 - -
S2.100.300.500.4.62E.S.289.G.EX.D... 10 96784063 - - 96782484
S2.100.300.500.4.62E.C.289.G.EX.D... 10 96784064 - - 96782484
S2.100.300.500.4.62E.D.289.G.EX.D... 10 96784065 - 96094525 -
S2.100.300.500.4.62E.H.289.G.EX.D... 10 96784067 96787499 - -
S2.145.300.200.8.62E.S.388.G.EX.D... 10 96784037 - - 96782484
S2.145.300.200.8.62E.C.388.G.EX.D... 10 96784038 - - 96782484
S2.145.300.200.8.62E.D.388.G.EX.D... 10 96784039 - 96308239 -
S2.145.300.200.8.62E.H.388.G.EX.D... 10 96784041 96787500 - -
S2.145.300.280.8.62E.S.421.G.EX.D... 10 96784042 - - 96782484
S2.145.300.280.8.62E.C.421.G.EX.D... 10 96784043 - - 96782484
S2.145.300.280.8.62E.D.421.G.EX.D... 10 96784044 - 96308239 -
S2.145.300.280.8.62E.H.421.G.EX.D... 10 96784046 96787500 - -
S3.120.300.150.12.62F.S.449.G.EX.D... 10 96784068 - - 96782484
S3.120.300.150.12.62F.C.449.G.EX.D... 10 96784069 - - 96782484
S3.120.300.150.12.62F.D.449.G.EX.D... 10 96784070 - 96308239 -
S3.120.300.150.12.62F.H.449.G.EX.D... 10 96784072 96787500 - -
1
Pumps of installation type H include the standard horizontal stand. Pumps with material code G or Q include a painted-steel stand. If another
horizontal stand is required, order a pump of installation type D together with the required stand.
2 Installation type S and C pumps with outlet flange size DN 250 and higher are supplied with a guide claw mounted on the flange.

15
5 S pumps, range 62

Stainless steel impeller, 3 x 400/690 V


Product range

Accessories

Cable length To be ordered separately


Pump type Pump Horizontal base
[m]
stand 1 Vertical base Auto-coupling
stand system 2
S1.80.125.300.4.62H.S.338.Q.EX.D... 10 96811646 - - 96782145
S1.80.125.300.4.62H.C.338.Q.EX.D... 10 96811648 - - 96782145
S1.80.125.300.4.62H.D.338.Q.EX.D... 10 96811649 - 96308238 -
S1.80.125.300.4.62H.H.338.Q.EX.D... 10 96811650 96787496 - -
S1.80.125.400.4.62H.S.374.Q.EX.D... 10 96811651 - - 96782145
S1.80.125.400.4.62H.C.374.Q.EX.D... 10 96811652 - - 96782145
S1.80.125.400.4.62H.D.374.Q.EX.D... 10 96811653 - 96308238 -
S1.80.125.400.4.62H.H.374.Q.EX.D... 10 96811654 96787496 - -
S1.80.125.500.4.62H.S.398.Q.EX.D... 10 96811655 - - 96782145
S1.80.125.500.4.62H.C.398.Q.EX.D... 10 96811656 - - 96782145
S1.80.125.500.4.62H.D.398.Q.EX.D... 10 96811657 - 96308238 -
S1.80.125.500.4.62H.H.398.Q.EX.D... 10 96811658 96787496 - -
S1.100.125.300.4.62M.S.314.Q.EX.D... 10 96811682 - - 96782145
S1.100.125.300.4.62M.C.314.Q.EX.D... 10 96811683 - - 96782145
S1.100.125.300.4.62M.D.314.Q.EX.D... 10 96811684 - 96094523 -
S1.100.125.300.4.62M.H.314.Q.EX.D... 10 96811685 96787497 - -
S1.100.125.400.4.62M.S.345.Q.EX.D... 10 96811686 - - 96782145
S1.100.125.400.4.62M.C.345.Q.EX.D... 10 96811687 - - 96782145
S1.100.125.400.4.62M.D.345.Q.EX.D... 10 96811688 - 96094523 -
S1.100.125.400.4.62M.H.345.Q.EX.D... 10 96811689 96787497 - -
S1.100.125.500.4.62M.S.367.Q.EX.D... 10 96811690 - - 96782145
S1.100.125.500.4.62M.C.367.Q.EX.D... 10 96811691 - - 96782145
S1.100.125.500.4.62M.D.367.Q.EX.D... 10 96811692 - 96094523 -
S1.100.125.500.4.62M.H.367.Q.EX.D... 10 96811693 96787497 - -
S2.100.200.400.4.62L.S.285.Q.EX.D... 10 96811665 - - 96641489
S2.100.200.400.4.62L.C.285.Q.EX.D... 10 96811666 - - 96641489
S2.100.200.400.4.62L.D.285.Q.EX.D... 10 96811667 - 96094525 -
S2.100.200.400.4.62L.H.285.Q.EX.D... 10 96811668 96787498 - -
S2.100.200.500.4.62L.S.290.Q.EX.D... 10 96811669 - - 96641489
S2.100.200.500.4.62L.C.290.Q.EX.D... 10 96811670 - - 96641489
S2.100.200.500.4.62L.D.290.Q.EX.D... 10 96811671 - 96094525 -
S2.100.200.500.4.62L.H.290.Q.EX.D... 10 96811672 96787498 - -
S2.100.300.300.4.62E.S.253.Q.EX.D... 10 96811673 - - 96782484
S2.100.300.300.4.62E.C.253.Q.EX.D... 10 96811674 - - 96782484
S2.100.300.300.4.62E.D.253.Q.EX.D... 10 96811675 - 96094525 -
S2.100.300.300.4.62E.H.253.Q.EX.D... 10 96811699 96787499 - -
S2.100.300.400.4.62E.S.281.Q.EX.D... 10 96811676 - - 96782484
S2.100.300.400.4.62E.C.281.Q.EX.D... 10 96811677 - - 96782484
S2.100.300.400.4.62E.D.281.Q.EX.D... 10 96811678 - 96094525 -
S2.100.300.400.4.62E.H.281.Q.EX.D... 10 96811700 96787499 - -
S2.100.300.500.4.62E.S.289.Q.EX.D... 10 96811679 - - 96782484
S2.100.300.500.4.62E.C.289.Q.EX.D... 10 96811680 - - 96782484
S2.100.300.500.4.62E.D.289.Q.EX.D... 10 96811681 - 96094525 -
S2.100.300.500.4.62E.H.289.Q.EX.D... 10 96811701 96787499 - -
S2.145.300.200.8.62E.S.388.Q.EX.D... 10 96811659 - - 96782484
S2.145.300.200.8.62E.C.388.Q.EX.D... 10 96811660 - - 96782484
S2.145.300.200.8.62E.D.388.Q.EX.D... 10 96811661 - 96308239 -
S2.145.300.200.8.62E.H.388.Q.EX.D... 10 96811697 96787500 - -
S2.145.300.280.8.62E.S.421.Q.EX.D... 10 96811662 - - 96782484
S2.145.300.280.8.62E.C.421.Q.EX.D... 10 96811663 - - 96782484
S2.145.300.280.8.62E.D.421.Q.EX.D... 10 96811664 - 96308239 -
S2.145.300.280.8.62E.H.421.Q.EX.D... 10 96811698 96787500 - -
S3.120.300.150.12.62F.S.449.Q.EX.D... 10 96811694 - - 96782484
S3.120.300.150.12.62F.C.449.Q.EX.D... 10 96811695 - - 96782484
S3.120.300.150.12.62F.D.449.Q.EX.D... 10 96811696 - 96308239 -
S3.120.300.150.12.62F.H.449.Q.EX.D... 10 96811702 96787500 - -
1
Pumps of installation type H include the standard horizontal stand. Pumps with material code G or Q include a painted-steel stand. If another
horizontal stand is required, order a pump of installation type D together with the required stand.
2 Installation type S and C pumps with outlet flange size DN 250 and higher are supplied with a guide claw mounted on the flange.

16
S pumps, range 62
6

6. Variants

Variants
List of variants
Motor
15 m
Various cable lengths 25 m
50 m
10 m
15 m
EMC power cables Screened power cables for variable-speed drives
25 m
50 m
Insulation class H
Special motor
Special voltage
PTC thermistors in windings
Special oil Non-toxic Shell Ondina X420 1

Motor protection
Pt100 on lower bearing + Pt100 on upper bearing + Pt100
Sensor set 2
on windings
Pt100 on lower bearing + Pt100 on upper bearing + Pt100
Sensor set 3
on windings + PVS3 vibration sensor
External water-in-oil sensor WIO

Coating
300 µm (painted twice)
Special paint thickness
450 µm (painted three times)
Epoxy coating (NCS 900N/RAL 9005 gloss 30, black)
Impeller (external surface)
Belzona 1321 coating (brush painted, blue)
Impeller (internal surface) Chesterton ARC 855 ceramic coating (grey)
Epoxy coating (NCS 900N/RAL 9005 gloss 30, black)
Pump housing (internal) Belzona 1321 coating (brush painted, blue)
Chesterton ARC 855 ceramic coating (grey)
Epoxy coating (NCS 900N/RAL 9005 gloss 30, black)
Inlet cover Belzona 1321 coating (brush painted, blue)
Chesterton ARC 855 ceramic coating (grey)
Zinc anodes (outside of inlet cover / pump housing) 3 pcs.

Materials
Stainless steel lifting bracket AISI 316
Stainless steel shaft AISI 329
Impeller Stainless steel

Tests
Test at specified duty on standard impeller curve
Trimmed impeller for specified duty test
Additional test of entire QH curve (including report) 5-10 pointsbase plate from pump performance curve
ISO 9906:2012 grade 1E
tolerances
ISO 9906:2012 grade 1B/1U
Different test standard Efficiency guaranteed by Grundfos
tolerances
ISO 9906:2012 grade 2B/2U
tolerances
Vibration test (including report) According to Grundfos factory quality standard
Performance test on dry test stand Contact Grundfos
NPSHr test Contact Grundfos
String test Contact Grundfos
Witness test Contact Grundfos

Miscellaneous
Special packaging Contact Grundfos
Special nameplate Contact Grundfos
Old UK-guide shoe Contact Grundfos / order guide shoe installation kit
Other variants Contact Grundfos
1
For pumps with WIO sensor Shell Ondina is not an option.

17
7 S pumps, range 62

7. Construction
Construction

Sectional drawings, motors


D-D
E-E 176d 176c 193 194 173b 173

B
520

520a

176a

176b

A A

25
100
178

B
248 252

A-A 250a
B-B
181 181a 250

168 250b

180
E E

198

164a

D D
190
157
177a 190b
61c
59b
154
48 157b
150
55

172
150c

60

182b 187
155 187a
72a
184
37a
72

153 193
58 194
109

59

182a
TM04 2306 0917

271

105b 270
26a
77 105 107

Fig. 6 Non-explosion-proof motor without cooling jacket (installation type S)

18
S pumps, range 62
7

Construction
176d 176c 173b 173
E-E
B D-D

520

193 520a
194

176a

A A
176b

25
100

178

B
A-A B-B 248 252
250a
181a

181 250
168 250b
180
E E

198

164a

D D
190
157
177a 190b
61c 59b

154

48
150
55

172

60

182b 187
155 187a
72a
184
72

153
58
109

59

182a
TM04 2307 0917

271
105b 270
26a
77 105 107

Fig. 7 Non-explosion-proof motor with cooling jacket (installation types C, D and H)

19
7 S pumps, range 62
Construction

G-G

520

D-D
E-E
B 176d 176c 193 194 173b 173

173f 520
173e
173d 520a

176a

A A
25
100
25a 176b

178

B 248 248a 252


B-B
181 A-A 181a 250

168 250a

180 250b

E E
180a
198

164a
D D
190
157
177a 190b
61c 59b
154
157b
48
150
55

172
150c

60
182b 187
155 187a
72a
184 G G
72 37a

153 193
58 194
109

59
182a
271
TM04 2309 0917

105b 270
26a
107
77 105

Fig. 8 Explosion-proof motor with cooling jacket (installation type S)

20
S pumps, range 62
7

Construction
G-G

520

E-E D-D
B 176c 176d 173b 173
173f
173e
173d 193 520

194 520a

H H
176a

A A
176b
25
100
25a

178

B 248 248a 252


B-B 250
A-A 181a
181 250a
168 250b
180

E E
180a
198

164a

D D
157
190
61c
177a
154 190b 59b

48
150
55

172

60

182b 187
155 187a
72a 184
G G
72

153
58
109

59
271
TM04 2308 0917

182a
270
105b
26a
77 105 107

Fig. 9 Explosion-proof motor without cooling jacket (installation types C, D and H)

21
7 S pumps, range 62

Sectional drawings, pumps


Construction

TM04 2310 0917

Fig. 10 Basic pump, installation types S and C

22
S pumps, range 62
7

Construction
702

703
701

TM04 2315 3916

Fig. 11 Installation types S and C pump on auto coupling

23
7 S pumps, range 62
Construction

TM04 2316 2308


Fig. 12 Installation type D, dry, vertical installation on base stand

TM04 2313 2308

Fig. 13 Installation type H, dry, horizontal installation on base stand

24
S pumps, range 62
7
Components and material specification

Construction
Motor
DIN W.Nr./ DIN W.Nr./
AISI/ AISI/
Pos. Component Material EN Pos. Component Material EN
ASTM ASTM
standard standard

7a Rivet Stainless steel 1.4436 316 250 Cable clamp PA or cast iron

25 Pressure-test plug Stainless steel 1.4436 316 250a Cable entry PA or cast iron

25a Screw Stainless steel 1.4436 316 250b Rubber seal

26a Screw Stainless steel 1.4436 316 250e Moisture switch

37a O-ring NBR rubber 252 Cable ATON

48 Stator 270 Nut

55 Stator housing Cast iron 1 EN-JL-1040 A48 30 271 Lock washer

58 Seal housing Cast iron 520 Moisture switch 3

Lower bearing-bracket 520a Screw Stainless steel 1.4436 316


59 Cast iron
cover
1
59b Pin Steel
Available in stainless steel (custom-built option).
2 Ex versions have cast iron cable entry.
60 Bearing-bracket cover Cast iron
3
Ex versions have two moisture switches.
61c Upper bearing bracket Cast iron
72 O-ring NBR rubber
72a O-ring NBR rubber
Pump
76a Approval plate
DIN W.Nr./
77 Seal-housing cover Cast iron AISI/
Pos. Component Material EN
ASTM
100 O-ring NBR rubber standard
SiC/SiC or 7a Rivet Stainless steel 1.4436 316
105 Mechanical seal
SiC/carbon
7b O-ring NBR rubber
SiC/SiC or
105b Mechanical seal 9a Key (for keyway) Stainless steel 1.4436 316
SiC/carbon
107 O-ring NBR rubber 12 Flange Cast iron

109 O-ring NBR rubber 12a Inlet cover Cast iron

150 Stator complete 12c Adjusting screw Stainless steel 1.4436 316

150c Cooling jacket Galvanized steel 26 Screw Stainless steel 1.4436 316

153 Ball bearing Stainless steel 26c Screw Stainless steel

154 Ball bearing Stainless steel 35 Screw Stainless steel

155 Lower bearing bracket Cast iron 1 35a Screw Stainless steel

157 O-ring NBR rubber 37 O-ring NBR rubber

157b O-ring NBR rubber 37b O-ring NBR rubber

164a Motor top cover Cast iron 39 O-ring NBR rubber

168 Cable entry PA or cast iron 2 39a O-ring NBR rubber

172 Shaft with rotor Stainless steel 1.4436 316 49 Impeller Cast iron1 EN-JL-1050

173 Screw Stainless steel 1.4436 316 50 Pump housing Cast iron 1 EN-JL-1050

173b Earth terminal Cast iron or


66 Cap
stainless steel
173c Washer Stainless steel 1.4436 316
66b Washer
173d Washer
67 Impeller screw Stainless steel 1.4436 316
173e Screw Stainless steel 1.4436 316
76 Nameplate
173f Spring washer Stainless steel 1.4436 316
76a Approval plate
173g Earth connector
301 Motor housing
176a Terminal block
487 Base stand, horizontal Cast iron or steel
176b Screw Stainless steel 1.4436 316
494 Plug Stainless steel 1.4436 316
176c Terminal block
495 O-ring NBR rubber
176d Terminal block
177a Protection sleeve 1
Available in stainless steel (custom-built option).
178 Screw Stainless steel 1.4436 316
180 Cable clamp PA or cast iron Accessories
180a Screw Stainless steel
181 Cable ATON Pos. Component Material
181a Screw Stainless steel 1.4436 316
487 Base stand, horizontal 1 Cast iron or steel
182a Screw
701 Auto-coupling base unit Cast iron 2
182b Screw Stainless steel 1.4436 316
702 Guide rail bracket Cast iron 2
184 Screw Stainless steel 1.4436 316
187 Circlip 703 Guide claw 3 Cast iron 2
187a Washer Stainless steel 1.4436 316 762 Base stand, vertical Cast iron or steel
188 Circlip 1
Pumps of installation type H include the standard horizontal stand.
190 Lifting bracket Steel
Pumps with material code G or Q include a painted-steel stand. If
190b Screw Stainless steel another horizontal stand is required, order a pump of installation
193 Plug Stainless steel 1.4408 316 type D together with the required stand.
2 Available in stainless steel (custom-built option).
194 O-ring NBR rubber
3
197 Washer Stainless steel 1.4436 316 Guide claws for DN 250 outlets or bigger are factory-fitted.
198 Rubber seal
248 Screw Stainless steel 1.4436 316
248a Screw Stainless steel

25
8 S pumps, range 62

8. Product description
Product description

Features Shaft seals


The pumps have a primary and a secondary shaft seal.
SmartTrim
The material combination of the primary shaft seal of
On conventional pumps, maintaining factory-set all pump types is silicon carbide/silicon carbide. For
impeller clearance is a time-consuming and costly the secondary shaft seal, the material combination is
task. The pumps need to be disconnected from the silicon carbide/carbon.
pipes and to be totally dismantled, and new parts need
The shaft seals are placed in the oil chamber of the
to be mounted in order to maintain full pumping
pump. The oil chamber provides reliable sealing
efficiency. Not so with Grundfos SmartTrim!
between the pumped liquid and the motor.
All Grundfos heavy-duty channel-impeller pumps,
The shaft seals have no springs or other parts in direct
whether for submerged or dry installation, are
contact with the pumped liquid. This prevents rags and
equipped with the unique SmartTrim impeller
fibres from getting caught. The shaft seals are
clearance adjustment system. This enables you to
bidirectional, meaning that they can operate in either
easily restore factory-set impeller clearance and
direction, thus allowing for opposite rotation caused by
maintain peak pumping efficiency All you need to do is
back-flow of liquid through the pump.
to tighten the adjustment screws on the exterior of the
impeller housing. This can be done on site, quickly and Motor
easily, without dismantling the pump and without using The motor is a watertight, totally encapsulated motor
special tools. with:
Efficiency drop in % • insulation class F (155 °C)
• temperature rise class F (105 K)
0
Factory-set impeller clearance • enclosure class IP68.
3 A For motor protection and sensors, see Sensors, page
27 below.
6

9
Cables
The pumps have H07RN-F AT power cables as
12
TM04 2391 2508

standard or screened ATON EMC VSCCB power


15 B cables on request.
Years The pumps have H07RN-F 450/750 V control cables
1 2 3 4 5 as standard or screened ATON VSCB 450/750 V
control cables on request.
Fig. 14 Impeller clearance adjustment cycle
The cables are 10 m long as standard. Other cable
A: With Grundfos SmartTrim impeller clearance lengths are available on request. See List of variants,
adjustment system page 17.
B: Without impeller clearance adjustment system The number and dimension of cables depend on the
SmartSeal motor size.

For pumps with DN 250 outlet and larger, the Grundfos Motor power
Voltage
Cable size
[kW] [power + control]
SmartSeal auto-coupling sealing mounted on the
pump outlet flange provides a completely leak-proof 15
2 x 4 x 6 mm2 +
20
connection between the pump and the base unit of the 1 x 7 x 1.5 mm 2
28
auto-coupling system. This optimises the efficiency of
30 3 x 415 V
the entire pumping system and keeps operating costs 41 3 x 400/690 V 2 x 4 x 10 mm2 +
at a minimum. 1 x 7 x 1.5 mm 2
43
Bearings 2 x 4 x 16 mm2 +
50
1 x 7 x 1.5 mm 2
The bearings are greased for life.
Main bearings: Double-row angular contact ball
bearing. Single or pair-mounted angular contact ball
bearings for axial forces and cylindrical roller bearing
for radial forces.
Support bearings: Single-row deep-groove ball
bearing.

26
S pumps, range 62
8
Power cable 2. PVS3 (pump vibration sensor)

Product description
The vibration sensor monitors the vibration level of
Outer cable the pump by using measurements of three axes and
Cable type Weight Bending radius
diameter
[mm2] [kg/m] [cm] combining them into a single measurement
[mm]
4x6 15.7 - 17.2 0.44 10 outputted in an analog current signal. The sensor
4 x 10 20.9 - 23.4 0.38 14 acts only as a general indicator of changes in the
4 x 16 23.8 - 26.3 1.26 16 vibration levels. PVS3 is to be connected to the
Grundfos IO 113 and SM 113 modules. A
Control cable
substantial increase in vibration will trigger a
Outer cable warning or an alarm.
Cable type Weight Bending radius
[mm2]
diameter
[kg/m] [cm]
An increase in vibrations can be caused by a
[mm] clogged impeller, worn bearings, closed force main
7 x 1.5 14.4 - 16.4 0.35 10 valves etc. indicating that service inspection must
Cable entry be carried out quickly in order to protect the pump
or the pipe system from being damaged.
Watertight PA or cast iron cable entry with soft shape
and sealing rings to prevent damage of the cable or 3. Bearing temperature sensor (Pt100).
leaks. Pt100 bearing temperature sensor installed within
the motor housing. Sensors to be connected using
Sensors a SM 113 and IO 113.
A standard pump is equipped with these switches and Testing
sensors:
All pumps are tested before leaving the factory. The
• Three thermal switches (Klixon) or three thermal
factory test report is based on ISO 9906:2012; grade
protectors in the stator housing
3B. Test reports can be ordered directly with the pump
• One moisture switch under the motor top cover. or can be ordered separately based on the pump serial
An explosion-proof pump is equipped with these number.
switches: Other tests or third-party inspection certificates are
• Three thermal switches (Klixon) or three thermal available on request. See List of variants, page 17.
protectors in the stator housing
• One moisture switch under the motor top cover and
one in the stator housing in the dry end of the motor.
Operating conditions
Customised sensor options Pumps without cooling jacket in submerged
installation (type S):
1. WIO (water-in-oil) sensor
The WIO sensor measures the water content in the • Continuous operation when the pump is fully
oil and converts the value into an analog current submerged to the top of motor.
signal. The two sensor conductors are for power • Intermittent operation with maximum 20 starts per
supply as well as for carrying the signal to the hour when the pump is submerged to the middle of
measuring device or controller. The sensor the motor and with short periods of operation down
measures the water content from 0 to 20 %. It also to the top of the pump housing.
sends a signal if the water content is outside the Warning: A motor protection device must be used
normal range (warning), or if there is air in the oil to cut off power supply in case of overheating.
chamber (alarm). The sensor is fitted in a stainless Note: Explosion-proof pumps must always be fully
steel tube for mechanical protection. submerged.
The sensor is either built-in with the motor (Ex) or
Pumps with cooling jacket in submerged and dry
installed as an accessory. If the sensor is installed
installation (types C, D and H):
externally, it is fitted in a plastic hose for mechanical
protection. The WIO sensor is connected to • Continuous and intermittent operation with
Grundfos IO 113. maximum 20 starts per hour with the water level
down to the top of the pump housing.

27
8 S pumps, range 62

Pumped liquids Level controllers


Product description

pH value: 4-10 Grundfos offers dedicated pump controllers for


Liquid temperature: 0-40 °C monitoring liquid levels in the wastewater collecting
When pumping liquids with a density and/or a tanks to ensure correct operation and protection of the
kinematic viscosity higher than that of water, use pumps.
motors with correspondingly higher outputs. Grundfos pump controllers are ideally suited to
Sound pressure Grundfos S pumps, and include:
• Grundfos Dedicated Controls (DC)
The sound pressure level of the pump is lower than the
limiting values stated in EC Council directive 2006/42/ • Grundfos LC controllers
EC relating to machinery (the EC Machinery Directive). Grundfos DC Controllers

Motor range
Motor power [kW] Number of poles
15 12
20 8
28 8
30 4
41 4
43 4
50 4

Explosion-proof pumps
Use explosion-proof pumps in potentially explosive
environments.

Gr-1016086
Note: All installations must be approved by the local
authorities.
Relevant standards/regulations Fig. 15 Grundfos Dedicated Controls control cabinet
• EN ISO 80079-36
Grundfos Dedicated Controls (DC) is a control system
• EN ISO 80079-37 designed for installation in municipal wastewater
• EN 60079-0 transportation, commercial buildings or network
• EN 60079-1 pumping stations with up to six wastewater pumps and
• IEC 60079-0 an optional mixer or a flush valve.
• IEC 60079-1 Advanced control and data communication are also
possible with the Grundfos Dedicated Controls system.
Explosion protection classification (IECEx & ATEX) The control cabinets are delivered with a built-in main
• Group II, Category 2, Gas or vapor environment switch and thermal magnetic circuit breaker.
• Ex db eb h mb IIB T3 or T4 Gb (Tamb = -5 °C to +40 Features and benefits:
°C) • Advanced Flow Calculation
Operation with frequency converter • Automatic energy optimisation
Only temperature class T3. • Easy installation and configuration
Notified body • Configuration wizard
• Electrical overview
SGS Baseefa
• Advanced data communication
• Advanced alarm and warning priority
• Supports several languages
• Daily emptying
• Mixer control or flush valve
• User-defined functions
• Anti-blocking
• Start level variation
• Advanced pump alternation with pump groups
• SMS scheduling
• Communication to SCADA, BMS, GRM or cell
phone.
Dedicated Controls is ordered either with or without a
built-in communication interface module (CIM).

28
S pumps, range 62
8
The communication module enables the possibility for IO 113

Product description
fieldbus protocol (e.g. PROFIBUS DP, Modbus RTU
The IO 113 module is a protection module for Grundfos
and PROFINET IO/Modbus TCP) and the
wastewater pumps.
communication line.
IO 113 has inputs for digital and analog pump sensors
For further information about Grundfos Dedicated
and can stop the pump if a sensor indicates a pump
Controls, please see Grundfos Product Center:
fault.
• Grundfos Dedicated Controls, brochure http://
IO 113 can be connected to the Grundfos Dedicated
net.grundfos.com/qr/i/96925597
Controls system and allows advanced monitoring
• Grundfos iSolutions, brochure http:// functions:
net.grundfos.com/qr/i/99249771
• motor temperature
• Grundfos Controls Guide, product guide http://
• moisture in motor
net.grundfos.com/qr/i/97954965
• water in oil
Additional features, CUE or VFD • insulation resistance.
The CUE/VFD (optional), which is either a Grundfos
variable frequency drive or a general variable SM 113
frequency drive, offers better pump protection and a The SM 113 module is used for collection and transfer
more steady flow through the pipe system. of sensor data in pumps and includes a large number
In addition, Grundfos CUE,VFD offers these features of sensors.
and benefits: SM 113 can be placed either inside the pump (allowing
• Anti-blocking fewer sensor conductors out of the pump) or in the
• Automatic energy optimisation control cabinet next to the pump installation.
• Specific-energy test SM 113 works together with IO 113 through a power-
• Output frequency line communication using the Grundfos GENIbus
• Monitoring of: protocol.
– voltage* SM 113 can collect data from:
– current* • 3 current sensors, 4-20 mA
– phase sequence* • 3 Pt100 thermal sensors or 3 Pt1000 thermal
sensors
– power*
• 1 PTC thermal sensor
– energy*
• 1 digital input.
– torque*
• Reverse start**
• Run flushing MP 204
• Stop flushing The MP 204 control cabinet can be used as a stand-
• PID control. alone motor protector. MP 204 may also be
* These functions are only available with a Grundfos incorporated in a Grundfos Dedicated Controls system
CUE. in which it functions as a motor protector. The pump is
** We do not recommend reversing at full speed at protected secondarily by measuring the temperature
any time. When reduced reverse operation settings with a Pt100 sensor and a PTC sensor or thermal
are set, make sure constant torque is enabled in switch.
Variable Frequency Drive (VFD) (i.e. Grundfos
CUE, Siemens Simatic, ABB, Schneider Electric
etc.) to have maximum torque available when
reversing.
Grundfos LC controllers
The LC 231 pump controller is designed for level
control, monitoring and protection of Grundfos
pumping stations featuring one pump or two pumps,
starting direct-on-line. The LC 231 controller is
integrated in a polymer cabinet.
The LC 241 is a modular pump controller that has a
metal or polymer cabinet and can be customised
according to your needs.
It is designed for level control, monitoring and
protection of Grundfos pumping stations featuring one
pump or two pumps, starting direct-on-line with 0-23 A,
star-delta with 0-59 A or soft starter with 0-72 A.

29
8 S pumps, range 62
Product description

Grundfos CUE, < 250 kW, or another


frequency converter.

Control cabinet

Dedicated Controls or PLC

IO 113 SM 113
T1 T2 G1 A1 G2 A2 K1 K2 R1 R2 PE

D1 D2 D3 D4 D5 D6 D7 D8 A Y B

Reset

ON DIP

1 2 3 4 5 6 7 8 9 10

P1 P2 P3 P4 P5 I1 I2 I3 1 2 3 4 5 6 7 8 9 1011 1213 14

Level sensor

SM 113, optional
1 2 3 4 5 6 7 8 9 1011 1213 14

PVS3 sensor, optional

Wiring diagram Pt100 sensor, PTC Moisture switch


optional
T2
Thermistor
T1
+t +t +t
WIO sensor, optional
Thermal switches
1 1 1
Moisture switches
2 2 2

3 3 3

4
Pt100 in lower bearing
4 4
9 1
8 2 5 5 5
7 3 Pt100 in stator
6 6 6
6 4 +t
5
Pt100 in upper bearing
7 7 7
+t
TM06 8753 1117

8 8 8
Oil indicator
4 to 20 mA
9 9 9

Fig. 16 Pump with frequency converter operation

30
S pumps, range 62
8

Product description
MP 204
MP 204

Control cabinet

Dedicated Controls or PLC

IO 113 SM 113
T1 T2 G1 A1 G2 A2 K1 K2 R1 R2 PE

D1 D2 D3 D4 D5 D6 D7 D8 A Y B

Reset

ON DIP

1 2 3 4 5 6 7 8 9 10

P1 P2 P3 P4 P5 I1 I2 I3 1 2 3 4 5 6 7 8 9 1011 1213 14

Level sensor

SM 113, optional
1 2 3 4 5 6 7 8 9 1011 1213 14

PVS3 sensor, optional

Wiring diagram PTC Moisture switch


Pt100 sensor,
optional
T2
Thermistor
T1
+t +t +t
WIO sensor, optional
Thermal switches
1 1 1
Moisture switches
2 2 2

3 3 3
Pt100 in lower bearing
4 4 4
9 1
8 2 5 5 5
7 3 Pt100 in stator
6 6 6
6 4 +t
5
Pt100 in upper bearing
7 7 7
+t
TM06 8754 1117

8 Oil indicator
8 8
4 to 20 mA
9 9 9

Fig. 17 Pump with MP 204 motor protector

31
8 S pumps, range 62

Wiring diagrams
Product description

Thermal switch Moisture switch and thermal


protectors

In Ex pumps 2 moisture switches

Motor
Read clockwise
from GND

Pt100 in lower bearing

Pt100 in stator

Thermistor

Supply cable conductors

176c
520d

176a

Stator conductors
TM04 3729 5008

Optional equipment

Fig. 18 Wiring diagrams, pumps with one power cable

Item Description
1 Female push-on connector
2 Wire pin
3 Butt splice
4 Ring connector
176a Terminal block (power cable connections)
176c Terminal block (sensor connections)
520d Moisture sensor

32
S pumps, range 62
8

Product description
Thermal switch Moisture switch and thermal protectors
Read clockwise
from GND
In Ex pumps 2 moisture switches Motor

Pt100 in lower bearing

Pt100 in stator

Thermistor

Supply cable conductors

176c

520d

176a

Stator conductors
TM043274 4008

Optional equipment

Fig. 19 Wiring diagrams, pumps with two power cables

Item Description
1 Female push-on connector
2 Wire pin
3 Butt splice
4 Ring connector
176a Terminal block (power cable connections)
176c Terminal block (sensor connections)
520d Moisture sensor

33
9 S pumps, range 62

9. Curve charts and technical data


Curve charts and technical data

The following many pages are divided into sections.


On pages 34 and 35 you will find a brief explanation of how to read the curve charts, the curve conditions, etc.

How to read the curve charts


Total pump head Max. efficiency mark Pump type
H = Htotal
62: Range 62
E: Pressure version (Extra-low pressure)
S: Installation type

p H
[kPa] [m]
14
62E.S
S2 50 Hz
.14
5.3
120 00. ISO 9906:2012 3B
12 28 0.8
421 .( QH curve for each individual pump
S2. )
100 145
10 .30
0.2
00.
8.(3
38)
80 8 NPSH
[m]
60 6 6
S2.145.300.280.8.(421)

40 4 4
NPSH curve for all variants shown.
When sizing the pumps, add a
20 2 S2.145.300.200.8.(338) 2 safety margin of at least 0.5 m

0 0 0
0 50 100 150 200 250 300 350 400 450 Q [l/s]

0 200 400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
24 S2.145.300.280.8.(421)
The power curves indicate the
20 pump shaft power [P2] for the
pumps shown
16 S2.145.300.200.8.(338)

TM04 0661 1914


12

8
0 50 100 150 200 250 300 350 400 450 Q [l/s]

Note: The pumps are tested according to ISO 9906:2012 grade 3B tolerance. Testing equipment and measuring
instruments are designed and calibrated according to the standards mentioned. The pumps are approved according to
tolerances for entire curves, specified in grade 3B.

34
S pumps, range 62
9
Curve conditions These tolerance grades can be used in the contract

Curve charts and technical data


between the pump manufacturer and the customer, or
The guidelines below apply to the curves shown in the they can be used in a default tolerance factor which
performance charts on pages 40-63. will apply if no specific tolerance grade has been
• Tolerances according to: ISO 9906:2012, grade 3B. agreed between the manufacturer and the customer.
• The curves show pump performance with different The performance acceptance grades are explained in
impeller diameters at rated speed. Specifying acceptance grades, pages 38 and 39,
• The curves apply to the pumping of airless water at showing the performance grades related to an ordinary
a temperature of 20 °C and a kinematic viscosity of pump curve.
1 mm2/s (1 cSt).
• NPSH: The curves show average values measured The guarantee point
under the same conditions as the performance According to ISO 9906:2012, the acceptance-grade
curves. tolerance applies to one guarantee point.
When sizing the pump, add a safety margin of at A guarantee point is defined by a guaranteed flow rate
least 0.5 m. and a guaranteed head.
• In case of densities other than 1000 kg/m3, the In addition, either minimum total efficiency or
outlet pressure is proportional to the density. maximum total input power may be guaranteed at the
• When pumping liquids with a density higher than specified conditions.
1000 kg/m3, motors with correspondingly higher This means that the standard sets guidelines for a duty
outputs must be used. point guaranteed for the following:
Calculation of total head – Q and H, or
The total pump head consists of the height difference – Q, H and total efficiency (Eta-total), or
between the measuring points + the differential head + – Q, H and total consumed power (P1).
the dynamic head. The guarantee point is defined by a minimum of five
measured test points.
H total = H geo + Hstat + Hdyn Example of a duty point test living up to ISO 9906:2012
requirements
Hgeo: Height difference between measuring points. H [m]
Hstat: Differential head between the inlet and the 20
outlet side of the pump.
18
Hdyn: Calculated values based on the velocity of the
16
pumped liquid on the inlet and the outlet side
14
of the pump.
12

10
Pump performance testing 8

S pump testers are all capable of performing hydraulic 6

performance tests according to ISO 9906:2012 4

TM07 0448 5117


requirements. 2

ISO 9906:2012 sets standards for "rotodynamic 0


0 20 40 60 80 100 120 140 160
pumps, Hydraulic performance acceptance tests,
Q [m3/h]
Grades 1, 2 and 3".
Fig. 20 Five measured test points are used to verify one
Performance acceptance grades guarantee point
Six-pump-performance-test acceptance grades, 3B,
2B, 2U, 1B, 1E and 1U are defined in ISO 9906:2012.
Mandatory Optional
Acceptance measurements measurements
grade
Q H P1 Eta-tot
3B ±9% ±7% +9 % -7 %
2B ±8% ±5% +8 %
-5 %
2U +16 % +10 % +16 %
1B ±5% ±3% +4 % -3 %
1E ±5% ±3% +4 %
≥ 0%
1U +10 % +6 % +10 %

Q: Flow rate
H: Head
P1: Total consumed power
Eta-tot: Total efficiency

35
9 S pumps, range 62

Evaluation of performance What Grundfos is able to guarantee for the different


Curve charts and technical data

acceptance grades will be evaluated on a case-by-


The test must show that the measured pump curve
case basis. Contact your local sales company on this.
touches or passes through a tolerance surrounding the
guarantee point, as defined by the selected Grundfos makes duty-point verification according to
acceptance grade. ISO 9906:2012 for one guarantee point at full speed,
50 or 60 Hz. The customer must tell Grundfos which
Guarantee-point evaluation must be made at the rated
duty point to verify.
speed, which for S pumps means 50 Hz or 60 Hz.
The requested duty point is verified by five measured
Head points.
Grade 1U duty-point verification
The following example illustrates performance testing
according to Grade 1U.
Pass Flow rate and head are mandatory, and efficiency or
H-
guaranteed power consumption, P1, is optional.
Fail
Tolerances for a Grade 1U test are as follows:
Pass
– Flow rate: 10 %

TM07 1544 1818


Pass Fail – Head: 6 %
– Efficiency: 0 %, only equal to or better than the
guaranteed value
Q-guaranteed Flow – P1: 10 %
Fig. 21 Pump curves that either pass or fail to cross the 1. Q, H and Eta-tot are tested and verified
tolerance cross of the guarantee point
H [m]
20
Performance-test types for end- 18
suction pumps 16
14
Two types of performance tests are available for S
12
pumps:
10
• duty-point-verification test 8
• curve test. 6
Tests carried out on S pumps 4

TM07 1542 1618


2
– Tests are saved for at least five years and can be
traced using the pump’s unique serial number. 0
0 200 400 600 800 1000 1200
– It is not possible to change acceptance grade on 3
Q [m /h]
an already tested and supplied pump; if required,
a re-test of the pump is made. Fig. 22 Measured values for flow rate and head

– Witness testing can be arranged.


Eta-tot % [m]
Duty-point-verification test, Grades 3B, 2B, 2U, 1B,
80
1E and 1U
70
This test method offers the possibility to perform a
duty-point verification of the following: 60

– Q and H; or 50

– Q, H and total efficiency (Eta-tot); or 40

– Q, H and total consumed power (P1). 30


20
TM07 1543 1618

Mandatory Optional
Acceptance measurements measurements 10
grade
Q H P1 Eta-tot 0
0 200 400 600 800 1000 1200
3B Standard On request Q [m3/h]
2B
On request On request Fig. 23 Measured values for total efficiency
2U
1B
1E On request On request
1U

36
S pumps, range 62
9
2. Q, H and P1 tested and verified In fig. 26 tolerance crosses according to Grade 3B

Curve charts and technical data


have been distributed across the complete
H [m]
performance range of a pump. We generate the upper
20 and lower limit of the performance curve by drawing
18 two curves at the outlines of these crosses.
16
When the pump is tested, and the measured point is
14 located within the range between the upper and lower
12 limit, it meets the ISO 9906:2012 Grade 3B tolerances.
10 This way of qualifying the pump performance is stricter
8 than a duty-point-verification test for Grade 3B.
6
4 How does Grundfos perform curve

TM07 1542 1618


2 testing for S pumps?
0
0 200 400 600 800 1000 1200
Grundfos applies two types of curve tests:
3
Q [m /h] • a reference-curve test
Fig. 24 Measured values for flow rate and head
• a performance-curve test.
Reference curve test, Grade 3B
P1 [kW] A reference curve test is made when no curve test
20 report is specified with the order. Three or four test
18 points are measured depending on production site,
16 and no curve test report is supplied with the pump.
14 Measurements are made to maintain and observe
12 continuous quality and to ensure that the supplied
10 pump is within test grade tolerances. Test grade
8 tolerances are set as for Grade 3B but without
6 certification.
TM07 1545 1618

4 Example of a reference curve test


2
0 H P1
0 200 400 600 800 1000 1200 [m] [kW]
Q [m3/h] 75 150
70 140
Fig. 25 Measured values for consumed power 65 130
60 120
Note that other points than the guarantee point can be 55 110

measured and displayed in a curve-test report 50 100


45 90
according to Grade 3B tolerances. 40 80
35 70
Curve test, Grade 3B 30 60
25 50
This test method is developed by Grundfos and is 20 40

TM07 1674 1918


based on ISO 9906:2012 performance acceptance 15 30

grade 3B tolerances: Q = ± 9 %, H = ± 7 %. 10 20
5 10
0 0
H [m] 0 100 200 300 Q [l/s]

Fig. 27 Measured values for tested pump







/RZHUOLPLW
TM07 1515 1618

 8SSHUOLPLW

6WDQGDUGFXUYH

     
Q [m3/h]

Fig. 26 Q-H curve with tolerance crosses on complete


performance range

37
9 S pumps, range 62

If the customer requires more points on the curve to be


Curve charts and technical data

H P1
[m] [kW] checked, individual measurements must be made,
75 150
70 140
which is not part of the performance curve test.
65 130
Static high pressure test
60 120
55 110 All produced pumps undergo a static high pressure
50 100
test of 1.5 x PN (nominal pressure of the pump).
45 90
40 80
35
30
70
60
Specifying acceptance grades
25 50
The graphs in the table on page 39 show the

TM07 1693 2018


20 40
15 30
tolerances as stated in the standard, related to an
10 20 ordinary pump curve. The graphs also show which
5 10 pump performance to expect if the customer, having
0
0 100 200 300 Q [l/s]
0
the same pump to start with, orders a pump with the
same guarantee point for different tolerances (B, E or
Fig. 28 The values in fig. 27 calculated to reference speed
U) within the acceptance grades.
for comparison to a reference performance curve
In some cases, it will not be possible to fulfil the same
If a pump performance report is requested at a later guarantee point for a unilateral tolerance as it will for a
stage, only reference test data are available. bilateral tolerance. This is indicated by the lower curve
for ‘E’ and ‘U’ grades.
Performance curve test, grade 3B
If the requested guarantee point is the same for a
A performance curve test is carried out when a curve Grade U pump as for a Grade B pump, the
test report is specified with the order. consequence of the production tolerances could be
The pump is tested at pre-specified flow rates and test that a larger pump is required to obtain the requested
grade tolerances are set as for Grade 3B but without duty point.
certification.
What Grundfos is able to guarantee for the different
Example of an S pump curve test acceptance grades will be evaluated on a case-by-
case basis. Contact your local sales company on this.
H P1
[m] [kW]
75 150 Acceptance grades and tolerances
70 140
65 130 Acceptance grade B
60 120
55 110 This acceptance grade refers to grades with a bilateral
50 100 tolerance on flow rate and head and with a tolerance
45 90 on efficiency.
40 80
35 70 Acceptance grade E
30 60
25 50 This acceptance grade refers to a grade with a
20 40 bilateral tolerance on flow rate and head but without
TM07 1674 1918

15 30 tolerance on efficiency.
10 20
5 10 Acceptance grade U
0 0
0 100 200 300 Q [l/s]
This acceptance grade refers to a grade with a
unilateral tolerance on flow rate and head. For the 2U
Fig. 29 Measured values for tested pump grade there is a tolerance on efficiency. For the 1U
grade there is no tolerance on efficiency.
H P1 Note that if the acceptance grade changes from Grade
[m] [kW]
75 150 1B to 1U, the customer does not necessarily get a
70 140 better pump with a higher efficiency. More likely, he
65 130
gets a pump where the performance is always to the
60 120
55 110
positive side of the guarantee point.
50 100
45 90
40 80
35 70
30 60
25 50
TM07 1693 2018

20 40
15 30
10 20
5 10
0 0
0 100 200 300 Q [l/s]

Fig. 30 The values in fig. 29 calculated to a reference


speed for comparison to a reference performance

38
S pumps, range 62
9

Curve charts and technical data


Acceptance grade
B E U
H
H: ±7%

Q: ±9%

Grade 3
Ș Ș: í7%

H H
H: ±5% H: +10%

Q: ±8% Q: +16%

Q Q

Grade 2
Ș Ș: í5% Ș Ș: í5%

Q Q

H H H
H: ±3% H: ±3% H: +6%

Q: ±5% Q: ±5% Q: +10%

Q Q Q

Grade 1
Ș: í3% Ș: •0% Ș: •0%
Ș Ș Ș

Q Q Q

Certificates Witness test


Certificates have to be confirmed for every order and When the pumps are being tested or are tested with a
are available on request as follows: certification, it is possible for the customer to witness
• certificate of compliance with the order (EN 10204 - the testing procedure according to ISO 9906:2012.
2.1) The witness test is not a certificate and will not result in
• pump test sheet. a written statement from Grundfos. The witness itself is
the only guarantee that everything is carried out as
prescribed in the testing procedure.
If the customer wants to witness the test, place this
request on the order.

39
10
Performance curves and technical data

10. Performance curves and technical data


Super-low pressure - 3 x 400/690 V
S3.120.300.150.12

p H
[kPa] [m]
8 S3.120.300.150.12.(449)
62F.S
50 Hz
70 7 ISO 9906:2012 3B

60 6

50 5

40 4

30 3 NPSH
[m]
20 2 4

10 1 S3.120.300.150.12.(449) 2

0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Q [m³/h]
P2
[kW]
14
S3.120.300.150.12.(449)
13

12

11

TM04 0665 1914


10

9
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 Q [l/s]

40
10

Performance curves and technical data


p H
[kPa] [m]
8 62F.C/D/H
S3.120.300.150.12.(449)
50 Hz
70 7 ISO 9906:2012 3B

60 6

50 5

40 4

30 3 NPSH
[m]
20 2 4

10 1 S3.120.300.150.12.(449) 2

0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Q [m³/h]
P2
[kW]
14
S3.120.300.150.12.(449)
13

12

11

TM04 0666 1914


10

9
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 Q [l/s]
Motor data

IN 1 Istart η motor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm 2] [Nm]
S3.120.300.150.12.62F.S.449... 18 15 12 485 Y/D 37/22 147 83 85 84 0.54 0.65 0.70 0.6500 581
S3.120.300.150.12.62F.C.449... 18 15 12 485 Y/D 37/22 147 83 85 84 0.54 0.65 0.70 0.6500 581
S3.120.300.150.12.62F.D.449... 18 15 12 485 Y/D 37/22 147 83 85 84 0.54 0.65 0.70 0.6500 581
S3.120.300.150.12.62F.H.449... 18 15 12 485 Y/D 37/22 147 83 85 84 0.54 0.65 0.70 0.6500 581
1
Low /high voltage (400/690 V).
Note: Enclosure class: IP68

Pump data

Impeller Maximum solids Pump housing Maximum installation


Moment of inertia *
Pump type diameter size pressure depth

[mm] [mm] PN [m] [kgm2]


S3.120.300.150.12.62F.S/C/D/H.449... 449 120 10 20 1,5293
* Applies to material code G (see Type key). For other material codes, please contact Grundfos.

41
10
Performance curves and technical data

Super-low pressure - 3 x 415 V


S3.120.300.150.12

p H
[kPa] [m]
8 S3.120.300.150.12.(449)
62F.S
50 Hz
70 7 ISO 9906:2012 3B

60 6

50 5

40 4

30 3 NPSH
[m]
20 2 4

10 1 S3.120.300.150.12.(449) 2

0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Q [m³/h]
P2
[kW]
14
S3.120.300.150.12.(449)
13

12

11

TM04 0665 1914


10

9
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 Q [l/s]

42
10

Performance curves and technical data


p H
[kPa] [m]
8 62F.C/D/H
S3.120.300.150.12.(449)
50 Hz
70 7 ISO 9906:2012 3B

60 6

50 5

40 4

30 3 NPSH
[m]
20 2 4

10 1 S3.120.300.150.12.(449) 2

0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 1100 1200 Q [m³/h]
P2
[kW]
14
S3.120.300.150.12.(449)
13

12

11

TM04 0666 1914


10

9
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320 340 Q [l/s]
Motor data

IN Istart η motor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S3.120.300.150.12.62F.S.449... 18 15 12 485 Y/D 36 142 83 85 84 0.54 0.65 0.70 0.6500 581
S3.120.300.150.12.62F.C.449... 18 15 12 485 Y/D 36 142 83 85 84 0.54 0.65 0.70 0.6500 581
S3.120.300.150.12.62F.D.449... 18 15 12 485 Y/D 36 142 83 85 84 0.54 0.65 0.70 0.6500 581
S3.120.300.150.12.62F.H.449... 18 15 12 485 Y/D 36 142 83 85 84 0.54 0.65 0.70 0.6500 581

Note: Enclosure class: IP68

Pump data

Impeller Pump housing Maximum installation Moment of


Maximum solids size
Pump type diameter pressure depth inertia*

[mm] [mm] PN [m] [kgm2]


S3.120.300.150.12.62F.S/C/D/H.449... 449 120 10 20 1,5293
*
Applies to material code G (see Type key). For other material codes, please contact Grundfos.

43
10
Performance curves and technical data

Extra-low pressure - 3 x 400/690 V


S2.145.300.200.8 and S2.145.300.280.8

p H
[kPa] [m]
14
62E.S
S2 50 Hz
.14
5.3
120 00. ISO 9906:2012 3B
12 28 0.8
421 .(
S2. )
100 145
10 .30
0.2
00.
8.(3
38)
80 8 NPSH
[m]
60 6 6
S2.145.300.280.8.(421)

40 4 4

20 2 S2.145.300.200.8.(338) 2

0 0 0
0 50 100 150 200 250 300 350 400 450 Q [l/s]

0 200 400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
24 S2.145.300.280.8.(421)

20

16 S2.145.300.200.8.(338)

TM04 0661 1914


12

8
0 50 100 150 200 250 300 350 400 450 Q [l/s]

44
10

Performance curves and technical data


p H
[kPa] [m]
14
62E.C/D/H
S2 50 Hz
.14
5.3
120 00. ISO 9906:2012 3B
12 280
.8.(
421
)
100 10 S2.1
45.3
00.2
00.8.(
338)
80 8 NPSH
[m]
60 6 S2.145.300.280.8.(421) 6

40 4 4

20 2 S2.145.300.200.8.(338) 2

0 0 0
0 50 100 150 200 250 300 350 400 450 Q [l/s]

0 200 400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
S2.145.300.280.8.(421)
24

20

S2.145.300.200.8.(338)
16

12

TM04 0662 1914


8
0 50 100 150 200 250 300 350 400 450 Q [l/s]

Motor data

IN 1 Istart η motor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S2.145.300.200.8.62E.S.388... 23 20 8 735 Y/D 41/24 268 85 88 89 0.62 0.73 0.80 0.5600 700
S2.145.300.200.8.62E.C.388... 23 20 8 735 Y/D 41/24 268 85 88 89 0.62 0.73 0.80 0.5600 700
S2.145.300.200.8.62E.D.388... 23 20 8 735 Y/D 41/24 268 85 88 89 0.62 0.73 0.80 0.5600 700
S2.145.300.200.8.62E.H.388... 23 20 8 735 Y/D 41/24 268 85 88 89 0.62 0.73 0.80 0.5600 700
S2.145.300.280.8.62E.S.421... 32 28 8 726 Y/D 56/33 268 87 89 87 0.71 0.81 0.84 0.5600 700
S2.145.300.280.8.62E.C.421... 32 28 8 726 Y/D 56/33 268 87 89 87 0.71 0.81 0.84 0.5600 700
S2.145.300.280.8.62E.D.421... 32 28 8 726 Y/D 56/33 268 87 89 87 0.71 0.81 0.84 0.5600 700
S2.145.300.280.8.62E.H.421... 32 28 8 726 Y/D 56/33 268 87 89 87 0.71 0.81 0.84 0.5600 700
1
Low /high voltage (400/690 V).
Note: Enclosure class: IP68

Pump data

Impeller Maximum solids Pump housing Maximum installation


Moment of inertia*
Pump type diameter size pressure depth

[mm] [mm] PN [m] [kgm2]


S2.145.300.200.8.62E.S/C/D/H.388... 388 0,9543
145 10 20
S2.145.300.280.8.62E.S/C/D/H.421... 421 1,2090
* Applies to material code G (see Type key). For other material codes, please contact Grundfos.

45
10
Performance curves and technical data

Extra-low pressure - 3 x 415 V


S2.145.300.200.8 and S2.145.300.180.8

p H
[kPa] [m]
14
62E.S
S2 50 Hz
.14
5.3
120 00. ISO 9906:2012 3B
12 28 0.8
421 .(
S2. )
100 145
10 .30
0.2
00.
8.(3
38)
80 8 NPSH
[m]
60 6 6
S2.145.300.280.8.(421)

40 4 4

20 2 S2.145.300.200.8.(338) 2

0 0 0
0 50 100 150 200 250 300 350 400 450 Q [l/s]

0 200 400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
24 S2.145.300.280.8.(421)

20

16 S2.145.300.200.8.(338)

12

TM04 0661 1914


8
0 50 100 150 200 250 300 350 400 450 Q [l/s]

46
10

Performance curves and technical data


p H
[kPa] [m]
14
62E.C/D/H
S2 50 Hz
.14
5.3
120 00. ISO 9906:2012 3B
12 280
.8.(
421
)
100 10 S2.1
45.3
00.2
00.8.(
338)
80 8 NPSH
[m]
60 6 S2.145.300.280.8.(421) 6

40 4 4

20 2 S2.145.300.200.8.(338) 2

0 0 0
0 50 100 150 200 250 300 350 400 450 Q [l/s]

0 200 400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
S2.145.300.280.8.(421)
24

20

S2.145.300.200.8.(338)
16

12

TM04 0662 1914


8
0 50 100 150 200 250 300 350 400 450 Q [l/s]

Motor data

IN Istart η motor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S2.145.300.200.8.62E.S.388... 23 20 8 735 Y/D 40 258 85 88 89 0.62 0.73 0.80 0.5600 700
S2.145.300.200.8.62E.C.388... 23 20 8 735 Y/D 40 258 85 88 89 0.62 0.73 0.80 0.5600 700
S2.145.300.200.8.62E.D.388... 23 20 8 735 Y/D 40 258 85 88 89 0.62 0.73 0.80 0.5600 700
S2.145.300.200.8.62E.H.388... 23 20 8 735 Y/D 40 258 85 88 89 0.62 0.73 0.80 0.5600 700
S2.145.300.280.8.62E.S.421... 32 28 8 726 Y/D 54 258 87 89 87 0.71 0.81 0.84 0.5600 700
S2.145.300.280.8.62E.C.421... 32 28 8 726 Y/D 54 258 87 89 87 0.71 0.81 0.84 0.5600 700
S2.145.300.280.8.62E.D.421... 32 28 8 726 Y/D 54 258 87 89 87 0.71 0.81 0.84 0.5600 700
S2.145.300.280.8.62E.H.421... 32 28 8 726 Y/D 54 258 87 89 87 0.71 0.81 0.84 0.5600 700

Note: Enclosure class: IP68

Pump data

Impeller Pump housing Maximum installation Moment of


Maximum solids size
Pump type diameter pressure depth inertia*

[mm] [mm] PN [m] [kgm 2]


S2.145.300.200.8.62E.S/C/D/H.388... 388 0,9543
145 10 20
S2.145.300.280.8.62E.S/C/D/H.421... 421 1,2090
* Applies to material code G (see Type key). For other material codes, please contact Grundfos.

47
10
Performance curves and technical data

Extra-low pressure - 3 x 400/690 V


S2.100.300.300.4, S2.100.300.400.4 and
S2.100.300.500.4

p H
[kPa] [m] S2.100.300.500.4.(289) 62E.S
180 18 50 Hz
S2.100.300.400.4.(281)
ISO 9906:2012 3B
160 16
140 14

120 12
S2.100.300.300.4.(253)
100 10

80 8
NPSH
[m]
S2.100.300.500.4.(289)
60 6 12

40 4 8

20 2 S2.100.300.300.4.(253) 4
S2.100.300.400.4.(281)
0 0 0
80 120 160 200 240 280 320 360 400 Q [l/s]

400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
S2.100.300.500.4(289)
45
40 S2.100.300.400.4.(281)
35
30 S2.100.300.300.4.(253)
25

TM04 0663 1914


20
15
80 120 160 200 240 280 320 360 400 Q [l/s]

48
10

Performance curves and technical data


p H
[kPa] [m]
62E.C/D/H
180 S2
18 S 2.
100
.10
0.3 50 Hz
.30 00.
0 .4 0 500 ISO 9906:2012 3B
160 0 .4 .4.
16 .(28 ( 28
1) 9)
140 14

120 12
S2
.10
100 0 .30
10 0 .30
0 .4.(
80 8 253 NPSH
)
[m]
S2.100.300.500.4.(289)
60 6 12

40 4 8

20 2 S2.100.300.300.4.(253) 4
S2.100.300.400.4.(281)
0 0 0
80 120 160 200 240 280 320 360 400 Q [l/s]

400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
S2.100.300.500.4.(289)
45
S2.100.300.400.4.(281)
40
35
S2.100.300.300.4.(253)
30
25

TM04 06641914
20
15
80 120 160 200 240 280 320 360 400 Q [l/s]

Motor data

IN 1 Istart ηmotor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm 2] [Nm]
S2.100.300.300.4.62E.S.253... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S2.100.300.300.4.62E.C.253... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S2.100.300.300.4.62E.D.253... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S2.100.300.300.4.62E.H.253... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S2.100.300.400.4.62E.S.281... 46 41 4 1464 Y/D 84/49 460 86 89 89 0.61 0.74 0.80 0.3000 700
S2.100.300.400.4.62E.C.281... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S2.100.300.400.4.62E.D.281... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S2.100.300.400.4.62E.H.281... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S2.100.300.500.4.62E.S.289... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.300.500.4.62E.C.289... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.300.500.4.62E.D.289... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.300.500.4.62E.H.289... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
1 Low /high voltage (400/690 V).
Note: Enclosure class: IP68

Pump data

Impeller Maximum solids Pump housing Maximum installation


Moment of inertia*
Pump type diameter size pressure depth

[mm] [mm] PN [m] [kgm 2]


S2.100.300.300.4.62E.S/C/D/H.253... 253 0,4070
S2.100.300.400.4.62E.S/C/D/H.281... 281 100 10 20 0,4680
S2.100.300.500.4.62E.S/C/D/H.289... 289 0,5010
*
Applies to material code G (see Type key). For other material codes, please contact Grundfos.

49
10
Performance curves and technical data

Extra-low pressure - 3 x 415 V


S2.100.300.300.4, S2.100.300.400.4 and
S2.100.300.500.4

p H
[kPa] [m] S2.100.300.500.4.(289) 62E.S
180 18 50 Hz
S2.100.300.400.4.(281)
ISO 9906:2012 3B
160 16
140 14

120 12
S2.100.300.300.4.(253)
100 10

80 8
NPSH
[m]
S2.100.300.500.4.(289)
60 6 12

40 4 8

20 2 S2.100.300.300.4.(253) 4
S2.100.300.400.4.(281)
0 0 0
80 120 160 200 240 280 320 360 400 Q [l/s]

400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
S2.100.300.500.4(289)
45
40 S2.100.300.400.4.(281)
35
30 S2.100.300.300.4.(253)
25

TM04 0663 1914


20
15
80 120 160 200 240 280 320 360 400 Q [l/s]

50
10

Performance curves and technical data


p H
[kPa] [m]
62E.C/D/H
180 S2
18 S 2.
100
.10
0.3 50 Hz
.30 00.
0 .4 0 500 ISO 9906:2012 3B
160 0 .4 .4.
16 .(28 ( 28
1) 9)
140 14

120 12
S2
.10
100 0 .30
10 0 .30
0 .4.(
80 8 253 NPSH
)
[m]
S2.100.300.500.4.(289)
60 6 12

40 4 8

20 2 S2.100.300.300.4.(253) 4
S2.100.300.400.4.(281)
0 0 0
80 120 160 200 240 280 320 360 400 Q [l/s]

400 600 800 1000 1200 1400 Q [m³/h]


P2
[kW]
S2.100.300.500.4.(289)
45
S2.100.300.400.4.(281)
40
35
S2.100.300.300.4.(253)
30
25

TM04 0664 1914


20
15
80 120 160 200 240 280 320 360 400 Q [l/s]

Motor data

IN Istart η motor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S2.100.300.300.4.62E.S.253... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S2.100.300.300.4.62E.C.253... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S2.100.300.300.4.62E.D.253... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S2.100.300.300.4.62E.H.253... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S2.100.300.400.4.62E.S.281... 46 41 4 1464 Y/D 82 437 87 89 89 0.62 0.75 0.79 0.3000 700
S2.100.300.400.4.62E.C.281... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S2.100.300.400.4.62E.D.281... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S2.100.300.400.4.62E.H.281... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S2.100.300.500.4.62E.S.289... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.300.500.4.62E.C.289... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.300.500.4.62E.D.289... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.300.500.4.62E.H.289... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718

Note: Enclosure class: IP68

Pump data

Impeller Maximum solids Pump housing Maximum installation


Moment of inertia*
Pump type diameter size pressure depth

[mm] [mm] PN [m] [kgm 2]


S2.100.300.300.4.62E.S/C/D/H.253... 253 0,4070
S2.100.300.400.4.62E.S/C/D/H.281... 281 100 10 20 0,4680
S2.100.300.500.4.62E.S/C/D/H.289... 289 0,5010
* Applies to material code G (see Type key). For other material codes, please contact Grundfos.

51
10
Performance curves and technical data

Low pressure - 3 x 400/690 V


S2.100.200.400.4 and S2.100.200.500.4

p H
[kPa] [m]
62L.S
S2.1
00.2 50 Hz
320 32 00.5
00.4
.(29 ISO 9906:2012 3B
0 )
280 S2.1
28 00.2
00.4
00.4
.(28
240 24 5)

200 20

160 16 NPSH
[m]
120 12 12

80 8 S2.100.200.500.4.(290) 8

40 4 S2.100.200.400.4.(285) 4

0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 Q [m³/h]
P2
[kW]
50 S2.100.200.500.4.(290)

40

30 S2.100.200.400.4.(285)

TM04 0669 1914


20

10
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Q [l/s]

52
10

Performance curves and technical data


p H
[kPa] [m]
62L.C/D/H
S2.1
00.2 50 Hz
320 32 00.5
00.4
. (290 ISO 9906:2012 3B
)
280 S2.1
28 00.2
00.4
00.4
.(28
240 24 5)

200 20

160 16 NPSH
[m]
120 12 12

80 8 S2.100.200.500.4.(290) 8

40 4 S2.100.200.400.4.(285) 4

0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 Q [m³/h]
P2
[kW]
50 S2.100.200.500.4.(290)

40 S2.100.200.400.4.(285)

30

20

TM04 0670 1914


10
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Q [l/s]

Motor data

IN 1 Istart ηmotor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S2.100.200.400.4.62L.S.285... 46 41 4 1464 Y/D 84/49 460 86 89 89 0.61 0.74 0.80 0.3000 700
S2.100.200.400.4.62L.C.285... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S2.100.200.400.4.62L.H.285... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S2.100.200.400.4.62L.D.285... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S2.100.200.500.4.62L.S.290... 56 50 4 1470 Y/D 102 527 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.200.500.4.62L.C.290... 56 50 4 1470 Y/D 102 527 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.200.500.4.62L.H.290... 56 50 4 1470 Y/D 102 527 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.200.500.4.62L.D.290... 56 50 4 1470 Y/D 102 527 89 90 89 0.63 0.74 0.80 0.3800 718
1
Low /high voltage (400/690 V).
Note: Enclosure class: IP68

Pump data

Impeller Pump housing Maximum installation Moment of


Maximum solids size
Pump type diameter pressure depth inertia*

[mm] [mm] PN [m] [kgm 2]


S2.100.200.400.4.62L.S/C/D/H.285... 285 0,4977
100 10 20
S2.100.200.500.4.62L.S/C/D/H.290... 290 0,4853
*
Applies to material code G (see Type key). For other material codes, please contact Grundfos.

53
10
Performance curves and technical data

Low pressure - 3 x 415 V


S2.100.200.400.4 and S2.100.200.500.4

p H
[kPa] [m]
62L.S
S2.1
00.2 50 Hz
320 32 00.5
00.4
.(29 ISO 9906:2012 3B
0 )
280 S2.1
28 00.2
00.4
00.4
.(28
240 24 5)

200 20

160 16 NPSH
[m]
120 12 12

80 8 S2.100.200.500.4.(290) 8

40 4 S2.100.200.400.4.(285) 4

0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 Q [m³/h]
P2
[kW]
50 S2.100.200.500.4.(290)

40

30 S2.100.200.400.4.(285)

20

TM04 0669 1914


10
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Q [l/s]

54
10

Performance curves and technical data


p H
[kPa] [m]
62L.C/D/H
S2.1
00.2 50 Hz
320 32 00.5
00.4
. (290 ISO 9906:2012 3B
)
280 S2.1
28 00.2
00.4
00.4
.(28
240 24 5)

200 20

160 16 NPSH
[m]
120 12 12

80 8 S2.100.200.500.4.(290) 8

40 4 S2.100.200.400.4.(285) 4

0 0 0
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Q [l/s]

0 100 200 300 400 500 600 700 800 900 1000 Q [m³/h]
P2
[kW]
50 S2.100.200.500.4.(290)

40 S2.100.200.400.4.(285)

30

TM04 0670 1914


20

10
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 Q [l/s]
Motor data

IN Istart ηmotor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S2.100.200.400.4.62L.S.285... 46 41 4 1464 Y/D 82 437 87 89 89 0.62 0.75 0.79 0.3000 700
S2.100.200.400.4.62L.C.285... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S2.100.200.400.4.62L.D.285... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S2.100.200.400.4.62L.H.285... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S2.100.200.500.4.62L.S.290... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.200.500.4.62L.C.290... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.200.500.4.62L.D.290... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S2.100.200.500.4.62L.H.290... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718

Note: Enclosure class: IP68

Pump data

Impeller Pump housing Maximum installation Moment of


Maximum solids size
Pump type diameter pressure depth inertia*

[mm] [mm] PN [m] [kgm2]


S2.100.200.400.4.62L.S/C/D/H.285... 285 0,4977
100 10 20
S2.100.200.500.4.62L.S/C/D/H.290... 290 0,4853
* Applies to material code G (see Type key). For other material codes, please contact Grundfos.

55
10
Performance curves and technical data

Medium pressure - 3 x 400/690 V


S1.100.125.300.4, S1.100.125.400.4 and
S1.100.125.500.4

p H
[kPa] [m] S1.1
0 0.12
5.5
00.4
.(367
62M.S
500 )
50 S1.1
00.1 50 Hz
25.4
450 00.4 ISO 9906:2012 3B
45 .(345
)
S1.1
400 00.1
40 25.3
00.4
.(314
)
350 35
300 30
250 25
200
NPSH
20
[m]
150 15 12
S1.100.125.300.4.(314)
100 10 8
S1.100.125.400.4.(345)
50 5 4
S1.100.125.500.4.(367)
0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [l/s]

0 50 100 150 200 250 300 350 400 450 Q [m³/h]


P2
[kW]
50 S1.100.125.500.4.(367)

40 S1.100.125.400.4.(345)

30 S1.100.125.300.4.(314)

20

TM04 0671 1914


10
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [l/s]

56
10

Performance curves and technical data


p H
[kPa] [m] S1.1
00.12
5.500
.4.(36
62M.C/D/H
7
)
500 S1.1
50 00.1
25.4
50 Hz
00.4
450 45 .(345
) ISO 9906:2012 3B
S1.1
00.1
400 40 25.3
00.4
.(314
)
350 35
300 30
250 25
200
NPSH
20
[m]
150 15 12

100 10 S1.100.125.300.4.(314) 8

50 5 S1.100.125.500.4.(367) 4
S1.100.125.400.4.(345)
0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [l/s]

0 50 100 150 200 250 300 350 400 450 Q [m³/h]


P2
[kW]
50 S1.100.125.500.4.(367)

40 S1.100.125.400.4.(345)

S1.100.125.300.4.(314)
30

TM04 0672 1914


20

10
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [l/s]

Motor data

IN 1 Istart ηmotor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S1.100.125.300.4.62M.S.314... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S1.100.125.300.4.62M.C.314... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S1.100.125.300.4.62M.D.314... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S1.100.125.300.4.62M.H.314... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S1.100.125.400.4.62M.S.345... 46 41 4 1464 Y/D 84/49 460 86 89 89 0.61 0.74 0.80 0.3000 700
S1.100.125.400.4.62M.C.345... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S1.100.125.400.4.62M.D.345... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S1.100.125.400.4.62M.H.345... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S1.100.125.500.4.62M.S.367... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S1.100.125.500.4.62M.C.367... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S1.100.125.500.4.62M.D.367... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S1.100.125.500.4.62M.H.367... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
1 Low /high voltage (400/690 V).
Note: Enclosure class: IP68

Pump data

Impeller Maximum solids Pump housing Maximum installation


Moment of inertia*
Pump type diameter size pressure depth

[mm] [mm] PN [m] [kgm 2]


S1.100.125.300.4.62M.S/C/D/H.314... 314 0,5120
S1.100.125.400.4.62M.S/C/D/H.345... 345 100 10 20 0,6417
S1.100.125.500.4.62M.S/C/D/H.367... 367 0,7450
* Applies to material code G (see Type key). For other material codes, please contact Grundfos.

57
10
Performance curves and technical data

Medium pressure - 3 x 415 V


S1.100.125.300.4, S1.100.125.400.4 and
S1.100.125.500.4

p H
[kPa] [m] S1.1
0 0.12
5.5 00.4
.(367
62M.S
500 )
50 S1.1
00.1 50 Hz
25.4
450 00.4 ISO 9906:2012 3B
45 .(345
)
S1.1
400 00.1
40 25.3
00.4
.(314
)
350 35
300 30
250 25
200
NPSH
20
[m]
150 15 12
S1.100.125.300.4.(314)
100 10 8
S1.100.125.400.4.(345)
50 5 4
S1.100.125.500.4.(367)
0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [l/s]

0 50 100 150 200 250 300 350 400 450 Q [m³/h]


P2
[kW]
50 S1.100.125.500.4.(367)

40 S1.100.125.400.4.(345)

30 S1.100.125.300.4.(314)

TM04 0671 1914


20

10
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [l/s]

58
10

Performance curves and technical data


p H
[kPa] [m] S1.1
00.12
5.500
.4.(36
62M.C/D/H
7
)
500 S1.1
50 00.1
25.4
50 Hz
00.4
450 45 .(345
) ISO 9906:2012 3B
S1.1
00.1
400 40 25.3
00.4
.(314
)
350 35
300 30
250 25
200
NPSH
20
[m]
150 15 12

100 10 S1.100.125.300.4.(314) 8

50 5 S1.100.125.500.4.(367) 4
S1.100.125.400.4.(345)
0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [l/s]

0 50 100 150 200 250 300 350 400 450 Q [m³/h]


P2
[kW]
50 S1.100.125.500.4.(367)

40 S1.100.125.400.4.(345)

S1.100.125.300.4.(314)
30

TM04 0672 1914


20

10
0 10 20 30 40 50 60 70 80 90 100 110 120 130 Q [l/s]
Motor data

IN Istart ηmotor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S1.100.125.300.4.62M.S.314... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S1.100.125.300.4.62M.C.314... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S1.100.125.300.4.62M.D.314... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S1.100.125.300.4.62M.H.314... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S1.100.125.400.4.62M.S.345... 46 41 4 1464 Y/D 82 437 87 89 89 0.62 0.75 0.79 0.3000 700
S1.100.125.400.4.62M.C.345... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S1.100.125.400.4.62M.D.345... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S1.100.125.400.4.62M.H.345... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S1.100.125.500.4.62M.S.367... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S1.100.125.500.4.62M.C.367... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S1.100.125.500.4.62M.D.367... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S1.100.125.500.4.62M.H.367... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718

Note: Enclosure class: IP68

Pump data

Impeller Maximum solids Pump housing Maximum installation


Moment of inertia*
Pump type diameter size pressure depth

[mm] [mm] PN [m] [kgm 2]


S1.100.125.300.4.62M.S/C/D/H.314... 314 0,5120
S1.100.125.400.4.62M.S/C/D/H.345... 345 100 10 20 0,6417
S1.100.125.500.4.62M.S/C/D/H.367... 367 0,7450
*
Applies to material code G (see Type key). For other material codes, please contact Grundfos.

59
10
Performance curves and technical data

High pressure - 3 x 400/690 V


S1.80.125.300.4, S1.80.125.400.4 and
S1.80.125.500.4

p H
[kPa] [m]
70
62H.S
S1.8
0.12 50 Hz
5 .500
.4.(3
600 98 ) ISO 9906:2012 3B
60 S1.8
0.125
.400.4
.( 374)
500 50 S1.8
0.125
.300.4
.( 338)
400 40 NPSH
[m]
300 30 S1.80.125.300.4.(338) 12

200 20 8
S1.80.125.400.4.(374)
100 10 4
S1.80.125.500.4.(398)

0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 Q [l/s]

0 50 100 150 200 250 300 350 400 Q [m³/h]


P2
[kW]
50 S1.80.125.500.4.(398)

40 S1.80.125.400.4.(374)

30 S1.80.125.300.4.(338)

20

TM04 0667 1914


10

0
0 10 20 30 40 50 60 70 80 90 100 110 Q [l/s]

60
10

Performance curves and technical data


p H
[kPa] [m]
70 S1.8
62H C/D/H
0 .125
. 500.4
.(398
50 Hz
)
600 60 S1.8 ISO 9906:2012 3B
0.1 25.40
0.4.(
374)
500 50 S1.80
.125.3
00.4.(
3 38)
400 40 NPSH
[m]
300 30 S1.80.125.300.4.(338) 12

200 20 8
S1.80.125.400.4.(374)
100 10 4

S1.80.125.500.4.(398)
0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 Q [l/s]

0 50 100 150 200 250 300 350 400 Q [m³/h]


P2
[kW]
50 S1.80.125.500.4.(398)
S1.80.125.400.4.(374)
40

30 S1.80.125.300.4.(338)

20

TM04 0668 1914


10

0
0 10 20 30 40 50 60 70 80 90 100 110 Q [l/s]

Motor data

IN 1 Istart ηmotor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S1.80.125.300.4.62H.S.338... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S1.80.125.300.4.62H.C.338... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S1.80.125.300.4.62H.D.338... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S1.80.125.300.4.62H.H.338... 34 30 4 1482 Y/D 67/39 460 84 87 89 0.52 0.64 0.73 0.3000 700
S1.80.125.400.4.62H.S.374... 46 41 4 1464 Y/D 84/49 460 86 89 89 0.61 0.74 0.80 0.3000 700
S1.80.125.400.4.62H.C.374... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S1.80.125.400.4.62H.D.374... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S1.80.125.400.4.62H.H.374... 48 43 4 1464 Y/D 88/51 460 87 89 89 0.63 0.75 0.80 0.3000 700
S1.80.125.500.4.62H.S.398... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S1.80.125.500.4.62H.C.398... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S1.80.125.500.4.62H.D.398... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
S1.80.125.500.4.62H.H.398... 56 50 4 1470 Y/D 102/59 527 89 90 89 0.63 0.74 0.80 0.3800 718
1 Low /high voltage (400/690 V).
Note: Enclosure class: IP68

Pump data

Impeller Pump housing Maximum installation Moment of


Maximum solids size
Pump type diameter pressure depth inertia*

[mm] [mm] PN [m] [kgm2]


S1.80.125.300.4.62H.S/C/D/H.338... 338 0,8605
S1.80.125.400.4.62H.S/C/D/H.374... 374 80 10 20 0,7360
S1.80.125.500.4.62H.S/C/D/H.398... 398 0,9210
*
Applies to material code G (see Type key). For other material codes, please contact Grundfos.

61
10
Performance curves and technical data

High pressure - 3 x 415 V


S1.80.125.300.4, S1.80.125.400.4 and
S1.80.125.500.4

p H
[kPa] [m]
70
62H.S
S1.8
0.12 50 Hz
5 .500
.4.(3
600 98 ) ISO 9906:2012 3B
60 S1.8
0.125
.400.4
.( 374)
500 50 S1.8
0.125
.300.4
.( 338)
400 40 NPSH
[m]
300 30 S1.80.125.300.4.(338) 12

200 20 8
S1.80.125.400.4.(374)
100 10 4
S1.80.125.500.4.(398)

0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 Q [l/s]

0 50 100 150 200 250 300 350 400 Q [m³/h]


P2
[kW]
50 S1.80.125.500.4.(398)

40 S1.80.125.400.4.(374)

30 S1.80.125.300.4.(338)

20

TM04 0667 1914


10

0
0 10 20 30 40 50 60 70 80 90 100 110 Q [l/s]

62
10

Performance curves and technical data


p H
[kPa] [m]
70 S1.8
62H C/D/H
0 .125
. 500.4
.(398
50 Hz
)
600 60 S1.8 ISO 9906:2012 3B
0.1 25.40
0.4.(
374)
500 50 S1.80
.125.3
00.4.(
3 38)
400 40 NPSH
[m]
300 30 S1.80.125.300.4.(338) 12

200 20 8
S1.80.125.400.4.(374)
100 10 4

S1.80.125.500.4.(398)
0 0 0
0 10 20 30 40 50 60 70 80 90 100 110 Q [l/s]

0 50 100 150 200 250 300 350 400 Q [m³/h]


P2
[kW]
50 S1.80.125.500.4.(398)
S1.80.125.400.4.(374)
40

30 S1.80.125.300.4.(338)

20

TM04 0668 1914


10

0
0 10 20 30 40 50 60 70 80 90 100 110 Q [l/s]
Motor data

IN Istart η motor [%] Cos φ Moment Breakdown


P1 P2 No. of Starting
Pump type RPM of inertia torque Mmax
[kW] [kW] poles method [A] [A] 1/2 3/4 1/1 1/2 3/4 1/1 [kgm2] [Nm]
S1.80.125.300.4.62H.S.338... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S1.80.125.300.4.62H.C.338... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S1.80.125.300.4.62H.D.338... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S1.80.125.300.4.62H.H.338... 34 30 4 1482 Y/D 64 437 84 87 89 0.52 0.65 0.74 0.3000 700
S1.80.125.400.4.62H.S.374... 46 41 4 1464 Y/D 82 437 87 89 89 0.62 0.75 0.79 0.3000 700
S1.80.125.400.4.62H.C.374... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S1.80.125.400.4.62H.D.374... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S1.80.125.400.4.62H.H.374... 49 43 4 1464 Y/D 86 437 87 89 89 0.64 0.76 0.79 0.3000 700
S1.80.125.500.4.62H.S.398... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S1.80.125.500.4.62H.C.398... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S1.80.125.500.4.62H.D.398... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718
S1.80.125.500.4.62H.H.398... 56 50 4 1470 Y/D 98 508 89 90 89 0.63 0.74 0.80 0.3800 718

Note: Enclosure class: IP68

Pump data

Impeller Pump housing Maximum installation Moment of


Maximum solids size
Pump type diameter pressure depth inertia*

[mm] [mm] PN [m] [kgm 2]


S1.80.125.300.4.62H.S/C/D/H.338... 338 0,8605
S1.80.125.400.4.62H.S/C/D/H.374... 374 80 10 20 0,7360
S1.80.125.500.4.62H.S/C/D/H.398... 398 0,9210
*
Applies to material code G (see Type key). For other material codes, please contact Grundfos.

63
11 S pumps, range 62

11. Accessories
Accessories

Accessories (for installation)


Pump type Installation accessories
Range 50-70 S and C DN 80-DN 200 without guide claw (guide claw included in auto-coupling kit)
Range 50-70 S and C DN 250-DN 600 with a guide claw mounted on the pump
Range 50-70 D Pump without installation accessories (available as separate kit)
Range 50-70 H Base stand for horizontal, dry installation supplied together with the pump.
Pumps with material code G or Q include a painted-steel stand. If another horizontal stand is required, order a pump of
installation type D together with the required stand.

Weight Product
Pictures Description Size PN
[kg] number

Cast iron, epoxy-coated auto-coupling system complete DN 150/DN 125 104 96782145
with:
• guide claw 1

Outlet flange
• base unit
• upper guide rail bracket
• gaskets and bolts. DN 200 250 10 96641489
TM06 9868 3417

Cast iron, epoxy-coated auto-coupling system complete


with:
DN 300 276 96782484
• base unit
• upper guide rail bracket.
1
Installation type S and C pumps with outlet flange size DN 250 and higher are supplied with a guide claw
mounted on the flange.
DN 125/DN 150 3 96829331
Intermediate guide rail bracket For guide rails longer than 6 m
DN 200-DN 600 8 96255842
Standard pipes.
Guide rails
Not supplied by Grundfos
Grundfos flange/Flygt flange
Outlet flange

DN 200/DN 200 - 3" 25 97908872


Adapter for Flygt auto coupling with:
TM06 9923 3617

• flange seal
• bolts. DN 300/DN 300 - 3" 120 10 97908892

DN 300/DN 300 - 4" 120 97908893

DN 150 51 96308238
Inlet flange

DN 200 100 96094523


Vertical base stand (without bend). 10
TM04 4035 0509

DN 250 135 96094525

DN 300 191 96308239

DN 150 50 96787496
Steel. DN 200 50 96787497
Base stand for horizontal, dry installation with:
TM04 4156 0909

• bolts DN 250 1 89 10 96787498


• gaskets
2
• anchor bolts. DN 250 67 96787499

DN 300 73 96787500
1
Pumps with L-hydraulic.
2 Pumps with E-hydraulic.
TM06 4971 3415

Special base stand for horizontal, dry installation with Contact


DN 250 -
customized height. Grundfos

64
S pumps, range 62
11

Accessories
Weight Product
Pictures Description Size PN
[kg] number

Bend
Pipe/pump inlet
Cast iron, epoxy-coated

L = 220 mm DN 150 33 99035997


L

TM04 4033 4117


L = 260 mm DN 200 45 10 99026266

L = 350 mm DN 250 64 99035998

L L = 400 mm DN 300 81 99035999

Reducing bend
Pipe/pump inlet
Cast iron, epoxy-coated

L = 250 mm DN 150/DN 100 34 99036005


99036006
L = 250 mm DN 150/DN 125 34

L = 300 mm DN 200/DN 150 64 99036007

L = 350 mm DN 250/DN 200 58 99036008


L

L = 400 mm DN 300/DN 200 100 10 99036009

L = 400 mm DN 300/DN 250 76 99036011

L = 450 mm DN 350/DN 250 93 99036012


L
TM04 4034 4117

L = 500 mm DN 400/DN 200 119 99036010

L = 500 mm DN 400/DN 250 118 99036013

L = 500 mm DN 400/DN 300 128 99036014

65
11 S pumps, range 62

Other accessories
Accessories

Product
Pictures Description Size
number
4m 98425788
Galvanised lifting chain with lifting link and safety hook. 6m 98425789
Certified.
Maximum lifting capacity 3200 kg. 8m 98425790
10 m 98425791

TM02 2626 5102


4m 98425805
Stainless steel lifting chain with lifting link and safety hook. 6m 98425806
Certified.
Maximum lifting capacity 3200 kg. 8m 98425807
10 m 98425808

Contact
TM06 4974 3415

Cable support bracket (case by case)


Grundfos

AMD.07.18.1430 mixer, 3 x 400 V, 50 Hz 99018155

Bracket for wall mounting 2" thread 96115291


TM06 5110 2518

Bracket for floor mounting 2" thread 96115292

Bracket for suspended mounting 2" thread 96115293

Tube for suspended mounting, length 3 m 2" thread 96115294

10 m cable 96003332
Float switch
20 m cable 96003695
TM02 0670 5000 TM01 6982 3999

10 m cable 96003421
Float switch for use in potentially explosive environments.
20 m cable 96003536

Bracket for float switches 96003338

Float switches with bracket

2 switches, 1 pump without alarm 62500013

3 switches, 1 pump with alarm 62500014


10 m cable
3 switches, 2 pumps with alarm 62500014

3 switches, 2 pumps with alarm 62500015

Float switches with bracket for use in potentially explosive environments

2 switches, 1 pump without alarm 62500016


TM02 0670 5000

3 switches, 1 pump with alarm 62500017


10 m cable
3 switches, 2 pumps with alarm 62500017

3 switches, 2 pumps with alarm 62500018


TM02 8860 0904

For 38 mm
Bracket for level electrodes 91713196
mounting pipe

66
S pumps, range 62
12

12. Dimensions

Dimensions
Recommendation for pump Pull-out strengths for anchor bolts
foundations Submerged installation on auto coupling (type S and
C):
Note: This applies only to pumps above 15 kW.
All rotating equipment generates vibrations as a mass, Auto-coupling base Pull-out resistance
Bolts
unit [kN]
such as an impeller or rotor, is turning at high speeds.
DN 100 5
Proper installation and anchorage of Grundfos pumps 4 x M16
DN 125/DN 150 1 8
and installation accessories is critical to limit vibrations
DN 200 16
and achieve reliable, trouble-free installation. It is
DN 250 4 x M24 30
important to note that all mechanically connected DN 300 40
pipes, fittings and supports of the pump are part of a DN 500 40
single system. 6 x M30
DN 600 40
The rotating mass of the entire pump, together with the 1 Pump outlet DN 125 and base plate outlet DN 150.
forces from the motor and hydraulics, will generate
disturbances related to the speed of the motor. Dry installation (type H and D):
Unbalance and impeller vane pass in hydraulics are Pull-out resistance
Dry installation Anchor bolts
the two most important frequencies affecting vibration. [kN]
When these frequencies coincide with the natural DN 100 3 x M20 18
frequency of the entire mechanical system, the DN 150 18
6 x M20
DN 200 18
vibration level will increase substantially.
DN 250 25
Pumps from Grundfos are designed and produced DN 300 25
according to the highest quality standards. The method DN 500/DN 400 1
6 x M24
25
and grade of balancing is specified by the DN 500 25
manufacturer in order to achieve acceptable vibration
1
levels. Although the pump itself can withstand rather Base plate inlet DN 500 and pump inlet DN 400.
high vibration levels under operating conditions without
considerable lifetime reduction, the pipes and
supportive structure might suffer and crack if vibration
levels are too high. Furthermore, noticeable noise
levels might be generated.
The likelihood of high vibration levels occurring is
increased in variable-speed applications where the
pump is operated over a range of speeds rather than
at a single constant speed. Most variable-speed drives
provide the possibility to exclude certain frequency
ranges to avoid operating areas with high vibrations.
To ensure acceptable vibration levels in the field, all
parts of the system must be sufficiently stiff and firmly
anchored to minimise vibrations:
• The foundation and concrete must be of adequate
strength to support the weight of the pump including
accessories, the weight of the liquid passing
through the pump and the forces generated by the
pump.
• As a rule of thumb, the mass of the concrete
foundation must be a minimum of three to five times
the mass of the supported equipment and must
have sufficient rigidity to withstand the axial,
transverse and torsional loadings generated by the
equipment.
• The foundation must be 15 cm wider than the base
plate for pumps up to 350 kW and 25 cm wider for
larger pumps.
• The concrete used in the foundation must have a
minimum tensile strength of 250 N/cm2. Epoxy grout
must always be used to secure the pump base plate
to the foundation.

67
12 S pumps, range 62

Basic pump
Dimensions

Installation types S and C


D

DT2

DN2 D02 x D2N

E DC02

Installation types D and H


D

D01 x D1N

DC10

MOT_H

!A
DT2
TM04 6361 2018 - TM04 6360 2118

DN2
D02 x D2N

HYDR_H
H

E DC02 DN1
C

Fig. 31 Basic pumps

68
S pumps, range 62
12
Note: Dimensions D01, D1N, DC10 and DN1 are equal to zero for installation types C and S because of the inlet type.

Dimensions
Pump type A C D D01 D02 D1N D2N DC02 DC10
S1.80.125.300.4.62H.C/S 1460 687 260 - 19 - 8 210 -
S1.80.125.300.4.62H.D/H 1502 690 260 M20 19 8 8 210 240
S1.80.125.400.4.62H.C/S 1460 687 260 - 19 - 8 210 -
S1.80.125.400.4.62H.D/H 1502 690 260 M20 19 8 8 210 240
S1.80.125.500.4.62H.C/S 1460 687 260 - 19 - 8 210 -
S1.80.125.500.4.62H.D/H 1502 690 260 M20 19 8 8 210 240
S1.100.125.300.4.62M.C/S 1488 690 276 - 19 - 8 210 -
S1.100.125.300.4.62M.D/H 1492 690 276 M20 19 8 8 210 295
S1.100.125.400.4.62M.C/S 1488 690 276 - 19 - 8 210 -
S1.100.125.400.4.62M.D/H 1492 690 276 M20 19 8 8 210 295
S1.100.125.500.4.62M.C/S 1488 690 276 - 19 - 8 210 -
S1.100.125.500.4.62M.D/H 1492 690 276 M20 19 8 8 210 295
S2.100.200.400.4.62L.C/S 1496 960 356 - 24 - 8 295 -
S2.100.200.400.4.62L.D/H 1519 960 356 M20 24 12 8 295 350
S2.100.200.500.4.62L.C/S 1496 960 356 - 24 - 8 295 -
S2.100.200.500.4.62L.D/H 1519 960 356 M20 24 12 8 295 350
S2.100.300.300.4.62E.C/S 1525 1235 484 - 24 - 12 400 -
S2.100.300.300.4.62E.D/H 1561 1235 484 M20 24 12 12 400 350
S2.100.300.400.4.62E.C/S 1525 1235 484 - 24 - 12 400 -
S2.100.300.400.4.62E.D/H 1561 1235 484 M20 24 12 12 400 350
S2.100.300.500.4.62E.C/S 1525 1235 484 - 24 - 12 400 -
S2.100.300.500.4.62E.D/H 1561 1235 484 M20 24 12 12 400 350
S2.145.300.200.8.62E.C/S 1515 1139 522 - 24 - 12 400 -
S2.145.300.200.8.62E.D/H 1569 1139 522 M20 24 12 12 400 400
S2.145.300.280.8.62E.C/S 1515 1139 522 - 24 - 12 400 -
S2.145.300.280.8.62E.D/H 1569 1139 522 M20 24 12 12 400 400
S3.120.300.150.12.62F.C/S 1515 1139 522 - 24 - 12 400 -
S3.120.300.150.12.62F.D/H 1569 1139 522 M20 24 12 12 400 400

HYDR MOT
Pump type DN1 DN2 DT2 E F H
H H
S1.80.125.300.4.62H.C/S - DN 125 22 440 523 230 315 1145
S1.80.125.300.4.62H.D/H DN 150 DN 125 22 440 523 272 357 1145
S1.80.125.400.4.62H.C/S - DN 125 22 440 523 230 315 1145
S1.80.125.400.4.62H.D/H DN 150 DN 125 22 440 523 272 357 1145
S1.80.125.500.4.62H.C/S - DN 125 22 440 523 230 315 1145
S1.80.125.500.4.62H.D/H DN 150 DN 125 22 440 523 272 357 1145
S1.100.125.300.4.62M.C/S - DN 125 22 440 552 245 343 1145
S1.100.125.300.4.62M.D/H DN 200 DN 125 22 440 552 249 347 1145
S1.100.125.400.4.62M.C/S - DN 125 22 440 552 245 343 1145
S1.100.125.400.4.62M.D/H DN 200 DN 125 22 440 552 249 347 1145
S1.100.125.500.4.62M.C/S - DN 125 22 440 552 245 343 1145
S1.100.125.500.4.62M.D/H DN 200 DN 125 22 440 552 249 347 1145
S2.100.200.400.4.62L.C/S - DN 200 26 660 646 240 351 1145
S2.100.200.400.4.62L.D/H DN 250 DN 200 26 660 646 263 374 1145
S2.100.200.500.4.62L.C/S - DN 200 26 660 646 240 351 1145
S2.100.200.500.4.62L.D/H DN 250 DN 200 26 660 646 263 374 1145
S2.100.300.300.4.62E.C/S - DN 300 33 800 869 266 380 1145
S2.100.300.300.4.62E.D/H DN 250 DN 300 33 800 869 302 416 1145
S2.100.300.400.4.62E.C/S - DN 300 33 800 869 266 380 1145
S2.100.300.400.4.62E.D/H DN 250 DN 300 33 800 869 302 416 1145
S2.100.300.500.4.62E.C/S - DN 300 33 800 869 266 380 1145
S2.100.300.500.4.62E.D/H DN 250 DN 300 33 800 869 302 416 1145
S2.145.300.200.8.62E.C/S - DN 300 33 700 907 225 370 1145
S2.145.300.200.8.62E.D/H DN 300 DN 300 33 700 907 279 424 1145
S2.145.300.280.8.62E.C/S - DN 300 33 700 907 225 370 1145
S2.145.300.280.8.62E.D/H DN 300 DN 300 33 700 907 279 424 1145
S3.120.300.150.12.62F.C/S - DN 300 33 700 907 225 370 1145
S3.120.300.150.12.62F.D/H DN 300 DN 300 33 700 907 279 424 1145

69
12 S pumps, range 62

Installation on auto-coupling system


Dimensions

Upper guide rail bracket dimensions

Model A Model B

TM06 9913 3617- TM06 9915 3617


X

Fig. 32 Installation dimensions for upper guide rail bracket

Auto coupling X
Product number Model Size [mm]

96782145 A DN 125/DN 150 210


96641489 DN 200
B 150
96782484 DN 300

Auto-coupling dimensions

G C

A H I J

E D K TM06 6497 1516

Fig. 33 Dimension for cast-iron base unit

Dimensions [mm]
Product number Size
A B C D E F G H I J K
96782145 DN 125/DN 150 450 502 280 280 78 0 78 340 300 300 420
96641489 DN 200 485 710 365 535 89 86 175 500 430 430 710
96782484 DN 300 1050 1260 614 830/160 1 127 99 226 780 710 710 1230

1 Six-bolt installation: distance between the front bolt hole and the middle bolt hole / distance between the middle bolt hole and the back bolt hole.

70
S pumps, range 62
12
Pump installation dimensions

Dimensions
C Z6
Z7
Z8
Z9

F
Z10
Installation S
Ex pumps
Z17G
Z17S

Installation S
ZL1 Std. pumps Z1
ZDC1 ZDN1 Z15 Z11
Z23
ZDT1 ZL2
S3OPR
Z01
Installation C

Z2 Z3 Z16
Z12B

TM04 6372 2118


Z4 Support block height

ZM Z12A

Fig. 34 Installation on auto-coupling system - version 1 (with support block)

Note: Height of the support block = 125 mm.


Note: Distance between the centre of the anchor bolt hole to the edge of the screw hole = 10 mm.

Pump type C F Z01 Z1 Z2 Z3 Z4 Z6 Z7 Z8 Z9 Z10 Z11 Z12A Z12B


S1.80.125.300.4.62H.C.xxx.G/Q 687 523 8 x 23 1435 300 123 280 1261 947 697 110 88 1605 80 400
S1.80.125.300.4.62H.S.xxx.G/Q 687 523 8 x 23 1435 300 123 280 1261 947 697 110 88 1605 80 400
S1.80.125.400.4.62H.C.xxx.G/Q 687 523 8 x 23 1435 300 123 280 1261 947 697 110 88 1605 80 400
S1.80.125.400.4.62H.S.xxx.G/Q 687 523 8 x 23 1435 300 123 280 1261 947 697 110 88 1605 80 400
S1.80.125.500.4.62H.C.xxx.G/Q 687 523 8 x 23 1435 300 123 280 1261 947 697 110 88 1605 80 400
S1.80.125.500.4.62H.S.xxx.G/Q 687 523 8 x 23 1435 300 123 280 1261 947 697 110 88 1605 80 400
S1.100.125.300.4.62M.C.xxx.G/Q 690 552 8 x 23 1463 300 123 280 1261 947 697 110 88 1618 100 400
S1.100.125.300.4.62M.S.xxx.G/Q 690 552 8 x 23 1463 300 123 280 1261 947 697 110 88 1618 100 400
S1.100.125.400.4.62M.C.xxx.G/Q 690 552 8 x 23 1463 300 123 280 1261 947 697 110 88 1618 100 400
S1.100.125.400.4.62M.S.xxx.G/Q 690 552 8 x 23 1463 300 123 280 1261 947 697 110 88 1618 100 400
S1.100.125.500.4.62M.C.xxx.G/Q 690 552 8 x 23 1463 300 123 280 1261 947 697 110 88 1618 100 400
S1.100.125.500.4.62M.S.xxx.G/Q 690 552 8 x 23 1463 300 123 280 1261 947 697 110 88 1618 100 400

Z17 Z23 S3OPR


Pump type Z15 Z16 ZDC1 ZDN1 ZDT1 ZL1 ZL2 ZM
G S Std. Ex Std. Ex
S1.80.125.300.4.62H.C.xxx.G/Q 280 575 3 3 435 435 605 605 240 DN 150 25 571 147 4 x M16
S1.80.125.300.4.62H.S.xxx.G/Q 280 575 3 3 717 1158 887 1328 240 DN 150 25 571 147 4 x M16
S1.80.125.400.4.62H.C.xxx.G/Q 280 575 3 3 435 435 605 605 240 DN 150 25 571 147 4 x M16
S1.80.125.400.4.62H.S.xxx.G/Q 280 575 3 3 717 1158 887 1328 240 DN 150 25 571 147 4 x M16
S1.80.125.500.4.62H.C.xxx.G/Q 280 575 3 3 435 435 605 605 240 DN 150 25 571 147 4 x M16
S1.80.125.500.4.62H.S.xxx.G/Q 280 575 3 3 717 1158 887 1328 240 DN 150 25 571 147 4 x M16
S1.100.125.300.4.62M.C.xxx.G/Q 280 575 3 3 463 463 618 618 240 DN 150 25 571 147 4 x M16
S1.100.125.300.4.62M.S.xxx.G/Q 280 575 3 3 745 1186 900 1341 240 DN 150 25 571 147 4 x M16
S1.100.125.400.4.62M.C.xxx.G/Q 280 575 3 3 463 463 618 618 240 DN 150 25 571 147 4 x M16
S1.100.125.400.4.62M.S.xxx.G/Q 280 575 3 3 745 1186 900 1341 240 DN 150 25 571 147 4 x M16
S1.100.125.500.4.62M.C.xxx.G/Q 280 575 3 3 463 463 618 618 240 DN 150 25 571 147 4 x M16
S1.100.125.500.4.62M.S.xxx.G/Q 280 575 3 3 745 1186 900 1341 240 DN 150 25 571 147 4 x M16

71
12 S pumps, range 62
Dimensions

C Z6
Z7
Z8
Z9

F Z10
Z17G
Z17S Installation S
Ex pumps

ZL1
Z15 Installation S
ZDT1 Std. pumps Z1
ZDC1 ZDN1 Z11
S3OPR Z23
Z01 Installation C
Z16

Z12B

Z13 Z 12A

TM04 6377 2118


Z2 Z3 ZM Z14

Z4

Fig. 35 Installation on auto-coupling system - version 2 (without support block)

Note: Z12A is the minimum recommended distance from pit bottom to bottom of pump inlet port.
Note: Z11 is the total height of the pump installed on Grundfos installation accessory in the pit.
Note: The pump in this figure might not be equal to Z12A + Z1.

Pump type C F Z01 Z1 Z2 Z3 Z4 Z6 Z7 Z8 Z9 Z10 Z11 Z12A Z12B


S2.100.200.400.4.62L.C.xxx.G/Q 960 646 8 x 23 1471 430 200 535 1721 1352 1052 170 88 1577 106 106
S2.100.200.400.4.62L.S.xxx.G/Q 960 646 8 x 23 1471 430 200 535 1721 1352 1052 170 88 1577 106 106
S2.100.200.500.4.62L.C.xxx.G/Q 960 646 8 x 23 1471 430 200 535 1721 1352 1052 170 88 1577 156 156
S2.100.200.500.4.62L.S.xxx.G/Q 960 646 8 x 23 1471 430 200 535 1721 1352 1052 170 88 1577 156 156
S2.100.300.300.4.62E.C.xxx.G/Q 1235 869 12 x 23 1500 551 200 670 2136 1627 1192 170 88 1640 140 256
S2.100.300.300.4.62E.S.xxx.G/Q 1235 869 12 x 23 1500 551 200 670 2136 1627 1192 170 88 1640 140 256
S2.100.300.400.4.62L.C.xxx.G/Q 1235 869 12 x 23 1500 551 200 670 2136 1627 1192 170 88 1640 140 256
S2.100.300.400.4.62L.S.xxx.G/Q 1235 869 12 x 23 1500 551 200 670 2136 1627 1192 170 88 1640 140 256
S2.100.300.500.4.62E.C.xxx.G/Q 1235 869 12 x 23 1500 551 200 670 2136 1627 1192 170 88 1640 140 256
S2.100.300.500.4.62E.S.xxx.G/Q 1235 869 12 x 23 1500 551 200 670 2136 1627 1192 170 88 1640 140 256
S2.145.300.200.8.62E.C.xxx.G/Q 1139 907 12 x 23 1490 551 200 670 2040 1531 1092 170 88 1671 181 256
S2.145.300.200.8.62E.S.xxx.G/Q 1139 907 12 x 23 1490 551 200 670 2040 1531 1092 170 88 1671 181 256
S2.145.300.280.8.62E.C.xxx.G/Q 1139 907 12 x 23 1490 551 200 670 2040 1531 1092 170 88 1671 181 256
S2.145.300.280.8.62E.S.xxx.G/Q 1139 907 12 x 23 1490 551 200 670 2040 1531 1092 170 88 1671 181 256
S3.120.300.150.12.62F.S.xxx.G/Q 1139 907 12 x 23 1490 551 200 670 2040 1531 1092 170 88 1621 131 256
S3.120.300.150.12.62F.S.xxx.G/Q 1139 907 12 x 23 1490 551 200 670 2040 1531 1092 170 88 1621 131 256

Z17 Z23 S3OPR


Pump type Z13 Z14 Z15 Z16 ZDC1 ZDN1 ZDT1 ZL1 ZL2 ZM
G S Std. Ex Std. Ex
S2.100.200.400.4.62L.C.xxx.G/Q 150 86 365 485 3 3 471 471 427 427 295 DN200 31 761 222 4 x M24
S2.100.200.400.4.62L.S.xxx.G/Q 150 86 365 485 3 3 753 1194 709 1150 295 DN200 31 761 222 4 x M24
S2.100.200.500.4.62L.C.xxx.G/Q 200 86 365 485 3 3 471 471 427 427 295 DN200 31 761 222 4 x M24
S2.100.200.500.4.62L.S.xxx.G/Q 200 86 365 485 3 3 753 1194 709 1150 295 DN200 31 761 222 4 x M24
S2.100.300.300.4.62E.C.xxx.G/Q 150 95 450 650 3 3 500 500 490 490 400 DN 300 32 901 222 4 x M24
S2.100.300.300.4.62E.S.xxx.G/Q 150 95 450 650 3 3 782 1223 772 1213 400 DN 300 32 901 222 4 x M24
S2.100.300.400.4.62L.C.xxx.G/Q 150 95 450 650 3 3 500 500 490 490 400 DN 300 32 901 222 4 x M24
S2.100.300.400.4.62L.S.xxx.G/Q 150 95 450 650 3 3 782 1223 772 1213 400 DN 300 32 901 222 4 x M24
S2.100.300.500.4.62E.C.xxx.G/Q 150 95 450 650 3 3 500 500 490 490 400 DN 300 32 901 222 4 x M24
S2.100.300.500.4.62E.S.xxx.G/Q 150 95 450 650 3 3 782 1223 772 1213 400 DN 300 32 901 222 4 x M24
S2.145.300.200.8.62E.C.xxx.G/Q 150 95 450 650 3 3 490 490 521 521 400 DN 300 32 901 222 4 x M24
S2.145.300.200.8.62E.S.xxx.G/Q 150 95 450 650 3 3 772 1213 803 1244 400 DN 300 32 901 222 4 x M24
S2.145.300.280.8.62E.C.xxx.G/Q 150 95 450 650 3 3 490 490 521 521 400 DN 300 32 901 222 4 x M24
S2.145.300.280.8.62E.S.xxx.G/Q 150 95 450 650 3 3 772 1213 803 1244 400 DN 300 32 901 222 4 x M24
S3.120.300.150.12.62F.S.xxx.G/Q 100 95 450 650 3 3 490 490 521 521 400 DN 300 32 901 222 4 x M24
S3.120.300.150.12.62F.S.xxx.G/Q 100 95 450 650 3 3 772 1213 803 1244 400 DN 300 32 901 222 4 x M24

72
S pumps, range 62
12
Dry, vertical installation on base stand

Dimensions
B A
DN2 XDC3

DC02 X03

D2N x D02
X10

DT2

X13
B X16

X131

X132
X17
F X15
X6
A

X05
0
12

TM06 7982 2118


XM1 E

Fig. 36 Dry, vertical installation on base stand

Pump type C E F X03 X05 X6 X10 X13 X131 X132 X14 X15
S1.80.125.300.4.62H.D 690 440 523 24 24 621 DN 150 450 150 120 290 520
S1.80.125.400.4.62H.D 690 440 523 24 24 621 DN 150 450 150 120 290 520
S1.80.125.500.4.62H.D 690 440 523 24 24 621 DN 150 450 150 120 290 520
S1.100.125.300.4.62M.D 690 440 552 24 24 719 DN 200 520 170 120 350 344
S1.100.125.400.4.62M.D 690 440 552 24 24 719 DN 200 520 170 120 350 344
S1.100.125.500.4.62M.D 690 440 552 24 24 719 DN 200 520 170 120 350 344
S2.100.200.400.4.62L.D 960 660 646 24 28 854 DN 250 600 200 150 460 692
S2.100.200.500.4.62L.D 960 660 646 24 28 854 DN 250 600 200 150 460 692
S2.100.300.300.4.62E.D 1235 800 646 24 28 854 DN 250 600 200 150 460 692
S2.100.300.400.4.62E.D 1235 800 646 24 28 854 DN 250 600 200 150 460 692
S2.100.300.500.4.62E.D 1235 800 646 24 28 854 DN 250 600 200 150 460 692
S2.145.300.200.8.62E.D 1139 700 907 24 28 882 DN 300 675 225 150 475 780
S2.145.300.280.8.62E.D 1139 700 907 24 28 882 DN 300 675 225 150 475 780
S3.120.300.150.12.62F.D 1139 700 907 24 28 882 DN 300 675 225 150 475 780

Pump type X16 X17 XDC3 DN2 DC02 D02 D2N DT2 XM1
S1.80.125.300.4.62H.D 2098 893 240 DN 125 210 19 8 24 6 x M24
S1.80.125.400.4.62H.D 2098 893 240 DN 125 210 19 8 24 6 x M24
S1.80.125.500.4.62H.D 2098 893 240 DN 125 210 19 8 24 6 x M24
S1.100.125.300.4.62M.D 2186 968 295 DN 125 210 19 8 26 6 x M24
S1.100.125.400.4.62M.D 2186 968 295 DN 125 210 19 8 26 6 x M24
S1.100.125.500.4.62M.D 2186 968 295 DN 125 210 19 8 26 6 x M24
S2.100.200.400.4.62L.D 2348 1117 350 DN 200 295 24 8 26 6 x M24
S2.100.200.500.4.62L.D 2348 1117 350 DN 200 295 24 8 26 6 x M24
S2.100.300.300.4.62E.D 2390 1117 350 DN 200 295 24 8 26 6 x M24
S2.100.300.400.4.62E.D 2390 1117 350 DN 200 295 24 8 26 6 x M24
S2.100.300.500.4.62E.D 2390 1117 350 DN 200 295 24 8 26 6 x M24
S2.145.300.200.8.62E.D 2426 1161 400 DN 300 400 24 12 33 6 x M24
S2.145.300.280.8.62E.D 2426 1161 400 DN 300 400 24 12 33 6 x M24
S3.120.300.150.12.62F.D 2426 1161 400 DN 300 400 24 12 33 6 x M24

73
12 S pumps, range 62
Dimensions

DC2 DN2

D2N x D02

Q2

DT2

QDC1 Q3
QDN1

D1N x D01

Q4

Q10
Q1

QZ1

Q5 Q6

Q8
TM04 2414 2018

Q03

Fig. 37 Dry, horizontal installation on base stand

74
S pumps, range 62
12

Dimensions
Pump type D F ∅ Q03 Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q10 QDC1
S1.80.125.300.4.62H.H 260 523 18 1495 290 815 375 115 500 390 815 240
S1.80.125.400.4.62H.H 260 523 18 1495 290 815 375 115 500 390 815 240
S1.80.125.500.4.62H.H 260 523 18 1495 290 815 375 115 500 390 815 240
S1.100.125.300.4.62M.H 276 552 18 1485 267 815 375 115 500 390 815 295
S1.100.125.400.4.62M.H 276 552 18 1485 267 815 375 115 500 390 815 295
S1.100.125.500.4.62M.H 276 552 18 1485 267 815 375 115 500 390 815 295
S2.100.200.400.4.62L.H 356 646 18 1512 281 1035 375 115 500 390 1015 350
S2.100.200.500.4.62L.H 356 646 18 1512 281 1035 375 115 500 390 1015 350
S2.100.300.300.4.62E.H 484 869 19 1554 320 1350 550 115 500 390 865 350
S2.100.300.400.4.62E.H 484 869 19 1554 320 1350 550 115 500 390 865 350
S2.100.300.500.4.62E.H 484 869 19 1554 320 1350 550 115 500 390 865 350
S2.145.300.200.8.62E.H 522 907 19 1567 302 1250 550 120 500 500 870 400
S2.145.300.280.8.62E.H 522 907 19 1567 302 1250 550 120 500 500 870 400
S3.120.300.150.12.62F.H 522 907 19 1567 302 1250 550 120 500 500 870 400

Pump type DN1 Q01 D1N QZ1 DN2 D2N D02 DC2 DT2 QZ1
S1.80.125.300.4.62H.H DN 150 M20 8 18 125 8 19 210 22 18
S1.80.125.400.4.62H.H DN 150 M20 8 18 125 8 19 210 22 18
S1.80.125.500.4.62H.H DN 150 M20 8 18 125 8 19 210 22 18
S1.100.125.300.4.62M.H DN 200 M20 8 18 125 8 19 210 22 18
S1.100.125.400.4.62M.H DN 200 M20 8 18 125 8 19 210 22 18
S1.100.125.500.4.62M.H DN 200 M20 8 18 125 8 19 210 22 18
S2.100.200.400.4.62L.H DN 250 M20 12 18 200 8 24 295 26 18
S2.100.200.500.4.62L.H DN 250 M20 12 18 200 8 24 295 26 18
S2.100.300.300.4.62E.H DN 250 M20 12 18 300 12 24 400 33 18
S2.100.300.400.4.62E.H DN 250 M20 12 18 300 12 24 400 33 18
S2.100.300.500.4.62E.H DN 250 M20 12 18 300 12 24 400 33 18
S2.145.300.200.8.62E.H DN 300 M20 12 23 300 12 24 400 33 23
S2.145.300.280.8.62E.H DN 300 M20 12 23 300 12 24 400 33 23
S3.120.300.150.12.62F.H DN 300 M20 12 23 300 12 24 400 33 23

75
13 S pumps, range 62

13. Weights
Weights

Weights include 10 m cable.


Weight
Pump type
[kg]
S1.80.125.300.4.62H.S.338... 600
S1.80.125.300.4.62H.C.338... 660
S1.80.125.300.4.62H.D.338... 720
S1.80.125.300.4.62H.H.338... 720
S1.80.125.400.4.62H.S.374... 600
S1.80.125.400.4.62H.C.374... 660
S1.80.125.400.4.62H.D.374... 720
S1.80.125.400.4.62H.H.374... 720
S1.80.125.500.4.62H.S.398... 620
S1.80.125.500.4.62H.C.398... 680
S1.80.125.500.4.62H.D.398... 740
S1.80.125.500.4.62H.H.398... 740
S1.100.125.300.4.62M.S.314... 600
S1.100.125.300.4.62M.C.314... 660
S1.100.125.300.4.62M.D.314... 650
S1.100.125.300.4.62M.H.314... 720
S1.100.125.400.4.62M.S.345... 600
S1.100.125.400.4.62M.C.345... 660
S1.100.125.400.4.62M.D.345... 635
S1.100.125.400.4.62M.H.345... 720
S1.100.125.500.4.62M.S.367... 620
S1.100.125.500.4.62M.C.367... 680
S1.100.125.500.4.62M.D.367... 740
S1.100.125.500.4.62M.H.367... 740
S2.100.200.400.4.62L.S.285... 640
S2.100.200.400.4.62L.C.285... 700
S2.100.200.400.4.62L.H.285... 770
S2.100.200.400.4.62L.D.285... 770
S2.100.200.500.4.62L.S.290... 660
S2.100.200.500.4.62L.C.290... 730
S2.100.200.500.4.62L.H.290... 790
S2.100.200.500.4.62L.D.290... 790
S2.100.300.300.4.62E.S.253... 760
S2.100.300.300.4.62E.C.253... 840
S2.100.300.300.4.62E.D.253... 800
S2.100.300.300.4.62E.H.253... 840
S2.100.300.400.4.62E.S.281... 760
S2.100.300.400.4.62E.C.281... 840
S2.100.300.400.4.62E.D.281... 800
S2.100.300.400.4.62E.H.281... 840
S2.100.300.500.4.62E.S.289... 780
S2.100.300.500.4.62E.C.289... 860
S2.100.300.500.4.62E.D.289... 820
S2.100.300.500.4.62E.H.289... 800
S2.145.300.200.8.62E.S.388... 820
S2.145.300.200.8.62E.C.388... 900
S2.145.300.200.8.62E.D.388... 860
S2.145.300.200.8.62E.H.388... 900
S2.145.300.280.8.62E.S.421... 820
S2.145.300.280.8.62E.C.421... 900
S2.145.300.280.8.62E.D.421... 860
S2.145.300.280.8.62E.H.421... 900
S3.120.300.150.12.62F.S.449... 820
S3.120.300.150.12.62F.C.449... 900
S3.120.300.150.12.62F.D.449... 860
S3.120.300.150.12.62F.H.449... 980

76
S pumps, range 62
14

14. Flange forces

Flange forces
The flange forces and moments are according to EN
Horizontal installations
ISO 5199.
Z Forces can be found for both horizontal and vertical
installations in Table B.3 in EN ISO 5199 by selecting
the correct flange dimension. Forces cannot be used
Y directly for end-suction wastewater pumps without
using a coefficient which can be found in Table B.5 in
EN ISO 5199 by selecting the correct pump family.
Z For Grundfos wastewater pumps, the pump families
Y and coefficients are as stated below.
Horizontally installed pumps
Pump family A4 = Coefficient 0.35

X
Vertically installed pumps
Pump family 10A = Coefficient 0.30

Vertical installations

X
Base unit

Z
TM06 4901 3115 - TM06 4903 3115 - TM06 4902 3115

Fig. 38 Pump characteristics

77
15 S pumps, range 62

15. Grundfos Product Center


Grundfos Product Center

Online search and sizing tool to help you make the right choice.
http://product-selection.grundfos.com

All the information you need in one place


Performance curves, technical specifications, pictures, dimensional
drawings, motor curves, wiring diagrams, spare parts, service kits,
3D drawings, documents, system parts. The Product Center displays
any recent and saved items - including complete projects - right on
the main page.
Downloads
On the product pages, you can download installation and operating

TM07 2384
instructions, data booklets, service instructions, etc. in PDF format.

2 3 4 5

TM07 2383

Pos. Description
1 This drop-down menu enables you to set the search function to "Products" or "Literature".
2 SIZING enables you to size a pump based on entered data and selection choices.
3 CATALOGUE gives you access to the Grundfos product catalogue.
REPLACEMENT enables you to find a replacement product.
Search results will include information on
4 the lowest purchase price
the lowest energy consumption
the lowest total life cycle cost.
5 LIQUIDS enables you to find pumps designed for aggressive, flammable or other special liquids.

78
79
ECM: 1307629

GRUNDFOS A/S
96805708 01.2021

www.grundfos.com
Telephone: +45 87 50 14 00
DK-8850 Bjerringbro . Denmark
Trademarks displayed in this material, including but not limited to Grundfos, the Grundfos logo and “be think innovate” are registered trademarks owned by The Grundfos Group. All rights reserved. © 2021 Grundfos Holding A/S, all rights reserved.

You might also like