Scribd
Upload
88 views5 pages

CMPE 30141 Module Plate 2

The document discusses the design of a 16-1 multiplexer circuit. It provides background information on multiplexers, explaining that they are switching circuits that select data to send to the output line. The activity aims to have students design a 16-1 multiplexer using AND and OR gates. To complete the activity, students will draw the circuit design of a 16-1 multiplexer and submit it using a digital drawing platform.

Uploaded by

Maki Palla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
88 views5 pages

CMPE 30141 Module Plate 2

The document discusses the design of a 16-1 multiplexer circuit. It provides background information on multiplexers, explaining that they are switching circuits that select data to send to the output line. The activity aims to have students design a 16-1 multiplexer using AND and OR gates. To complete the activity, students will draw the circuit design of a 16-1 multiplexer and submit it using a digital drawing platform.

Uploaded by

Maki Palla
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Activity No.

MULTIPLREXER DRAWING DESIGN


CIRCUIT
Course Code: CPE 30141 Program:
Course Title: Comp. Eng’g Drafting and Design Date Performed: Nov 11, 2021
Section: BSCOE3-2 Date Submitted: Nov 11, 2021
Name: John Marc Palla Instructor: Engr. Velasco

1. Objective(s):
The activity aims to show the functional diagram of a general digital multiplexers. The inputs
and outputs are drawn as wide arrows design practice.
2. Intended Learning Outcomes (ILOs):
The students shall be able to provide an opportunity to design 16 to 1 multiplexer
combinational drawing circuit exercise.
3. Discussion:
Digital multiplexers are sometimes also referred to as “Data Selectors” as they select the
data to be sent to the output line and are commonly used in communications or high-speed network
switching circuits such as LAN´s and Ethernet applications.

Some multiplexer IC´s have a single inverting buffer (NOT Gate) connected to the output
to give a positive logic output (logic “1”, HIGH) on one terminal and a complimentary negative
logic output (logic “0”, LOW) on another different terminal.

It is possible to make simple multiplexer circuits from standard AND and OR gates as we
have seen above, but commonly multiplexers/data selectors are available as standard i.c. packages
such as the common TTL 74LS151 8-input to 1 line multiplexer or the TTL 74LS153 Dual 4-input
to 1 line multiplexer. Multiplexer circuits with much higher number of inputs can be obtained by
cascading together two or more smaller devices.

Multiplexer Summary

Then we can see that Multiplexers are switching circuits that just switch or route signals
through themselves, and being a combinational circuit, they are memoryless as there is no signal
feedback path. The multiplexer is a very useful electronic circuit that has uses in many different
applications such as signal routing, data communications and data bus control applications.
When used with a demultiplexer, parallel data can be transmitted in serial form via a single
data link such as a fiber-optic cable or telephone line and converted back into parallel data once
again. The advantage is that only one serial data line is required instead of multiple parallel data
lines. Therefore, multiplexers are sometimes referred to as “data selectors”, as they select the data
to the line.

Multiplexers can also be used to switch either analogue, digital or video signals, with the
switching current in analogue power circuits limited to below 10mA to 20mA per channel in order
to reduce heat dissipation.

In the next tutorial about combinational logic devices, we will look at the reverse of
the Multiplexer called the Demultiplexer which takes a single input line and connects it to
multiple output lines

5. Procedure:
1. Draw 16-1 multiplexers. The 16-1 is for combination of a selection input the
data line is connected to the output line. The 16-to 1 multiplexer requires
AND gates and OR gate and 4 selection lines. As an input the combination
of selection inputs is giving to the AND gate with the corresponding input
data lines. In this 16 to 1 multiplexer gives a value of 1 and the remaining
all AND gates give 0 and put a value to selected gates.
2. Conceptualize your own design and be ready to submit on your gdrive.
3. Logisim, multi sim, circuit wizard, Visio or any software drawing platform is
accepted. No prescribe software

DATA RESULT TIME STARTED TIME FINISHED TOTAL TIME

12:00PM 2:00PM 2HRS


6. Output:

You might also like