Scribd
Upload
91 views8 pages

Mini-Line Vögele Converter Kit: Installation Guide

Uploaded by

Ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
91 views8 pages

Mini-Line Vögele Converter Kit: Installation Guide

Uploaded by

Ali
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Mini-Line®

Vögele
Converter Kit

Installation
Guide
Copyright
All information, text and pictures are the intellectual property of, and copyrighted
material of TF-Technologies A/S. All rights are reserved. The installation guide
may not be copied, displayed, quoted, published, sold, modified, or distributed
without the written consent of TF-Technologies A/S.
Disclaimer
TF-Technologies A/S and its distributors may not be held liable for potential edi-
torial errors, omissions or failure effects. Suggestions regarding updates or cor-
rection of potential errors are appreciated.
User manual information
Document name: Mini-Line ® Vögele Converter Kit Installation Guide
Document number: G700703
Publication date: 5 March 2015
Installation Guide

The Mini-Line® Vögele Converter Kit


The Mini-Line® Vögele Converter Kit is Consists of
specially made to connect the Mini-Line®
Grade and Slope Control System to
Vögele asphalt pavers. The Vögele Con- • 1 Harting 10-pin rectangular
verter Kit provides an interface between connector (for connection to
the Mini-Line® Grade and Slope Control paver)
System and a Vögele asphalt paver with
a Harting connector for external level- • 2x adaptor boxes with 10-pin
ling systems and PNP driven solenoid plugs, one for the left and one
valves. for the right side of the paver,
(for connection to the
The Vögele Converter Kit enables Mini-Line® Grade and Slope
connection of the Mini-Line ® Grade Control System)
and Slope Control System to Vögele
asphalt pavers, by functioning as an • 2x4m coiled cables (when fully
adaptor cable as well as an interface extended) connected to the
that deactivates the regulation during adaptor boxes and the Harting
the standby mode used by Vögele pav- connector
ers.

When the Vögele Converter Kit is


mounted, the Mini-Line ® Grade and
Slope Control System is easily connected
to the adaptor boxes of the Vögele
Converter Kit by using the standard Additional Information
V-cables or W-cables of the system or The Vögele Converter Kit is designed
the Mini-Line ® Connector Box. for use with the Mini-Line ® Grade and
Slope Control System.
Mini-Line® Vögele
Converter Kit General recommendations of the manual
S-50288 for the Mini-Line ® Grade and Slope
Control System should be observed for
all additional subjects not covered in
this installation guide, including:

• Safety instruction
• Safe mounting and connection
with the Mini-Line ® Grade and
Slope Control System
• Information about overcurrent
protection
• Maintance

3
Installation Guide

Mounting
The Vögele Converter Kit is designed for
permanent mounting, and is resistant
to corrosive substances and the tough
environmental conditions on a paver.

The adaptor boxes should be placed


where it is practical to reach while con-
necting the Mini-Line® Grade and Slope
Control System, and where the cables
are protected from clamping.

The adaptor boxes feature labels indi-


cating which side (LEFT or RIGHT) of
the screed they should be mounted in.
Before mounting, the operator must en-
sure that the adaptor box with LEFT la- Mounting Holes
bel is mounted in the left side and vice
versa.

If mounted on the screed, protection


against overextension and dragging is
also needed.

Step-by-step instruction for permanent mounting


1.
2.
3.

1
Open the adaptor box
Open the adaptor boxes by loosening the four screws on the front

2
Map the position
Map the position of the two mounting holes shown on the
picture above on the paver

3
Mount the adaptor box
Mount the adaptor boxes on the paver with 4mm or 5/32 inch
screws

4
Installation Guide

Setting the Reception of the Standby Signal


When a Vögele asphalt paver is in standby Factory default setting
mode, the paver sends a signal to the lev-
elling equipment to deactivate regulation.
The Vögele Converter Kit facilitates the
reception of this signal in the Mini-Line®
Grade and Slope Control System.

Normally, it is not necessary to change the


setting for how the Vögele Converter Kit
receives the standby signal as the factory
setting should suit most Vögele pavers.
Option 2
The default setting of the Vögele Convert-
er Kit enables the regulation from the Mi-
ni-Line® Grade and Slope Control System,
when the standby input is pulled high,
and deactivates the regulation when the
standby input is left floating.

If the paver uses a high output to deacti-


vate the regulation, then change the set- Figure 1 - Changing Settings
tings to “Option 2” in both adaptor boxes.

Step-by-step instruction for changing settings


1.
2.
3.

1
Open the adaptor box
Open the adaptor boxes by loosening the four screws on the front

2
Identify the location
Identify the location of the jumper in figure 1

3
Change settings
The setting can be changed by moving the jumper from the
default setting to “Option 2”

Factory default setting Option 2

5
Kratbjerg 214 - DK 3480 Fredensborg - Denmark - Phone: +45 48 48 26 33 - Email: [email protected]
www.tf-technologies.com

You might also like