Siprotec Multi-Functional Protectiv Relays 7SJ61... 7SJ64 Overcurrent Protection 7SJ80 Motor Protection 7SK80

Preface, Table of Contents
Applications 1
SIPROTEC Basics 2
Mapping 3
Multi-Functional Protectiv
Relays Literature, Index
7SJ61...7SJ64
Overcurrent Protection
7SJ80
Motor Protection
7SK80
IEC 61850
PIXIT
C53000-G1140-C211-4
Disclaimer of Liability Copyright
We have checked the text of this manual against the hardware and Copyright © Siemens AG 2010
software described. However, deviations from the description can- Dissemination or reproduction of this document, or evaluation and
not be completely ruled out, so that no liability can be accepted for communication of its contents, is not authorized except where ex-
any errors or omissions contained in the information given. pressly permitted. Violations are liable for damages. All rights re-
The information given in this document is reviewed regularly and served, particularly for the purposes of patent application or
any necessary corrections will be included in subsequent editions. trademark registration.
We appreciate any suggestions for improvement.
We reserve the right to make technical improvements without no- Registered Trademarks
tice. SIPROTEC, SINAUT, SICAM and DIGSI are registered trademarks
of Siemens AG. Other designations in this manual might be trade-
Document Release V04.20.00 marks whose use by third parties for their own purposes would in-
Edition 03.2010 fringe the rights of the owner.
Siemens Aktiengesellschaft Order No.: C53000-G1140-C211-4

Preface
Purpose of this manual

In this Manual, you will find the
Specification of the applications of the IEC 61850 interface
General information about the effects of configuration of your device to the different Logical
Nodes and DOIs
Mapping of device relevant information to Logical Nodes as part of protocol IEC61850
Target audience
This manual is intended mainly for all persons who configure, parameterize and operate a
SIPROTEC Devices 7SJ61, 7SJ62, 7SJ63, 7SJ64, 7SJ80, 7SK80.
Scope of validity of this Manual

SIPROTEC 7SJ61, 7SJ62 and 7SJ64, Versions 4.7, 4.8
SIPROTEC 7SJ63, Version 4.66
SIPROTEC 7SJ80, Version 4.6
SIPROTEC 7SK80, Version 4.6
Standards
This document has been created according to the ISO 9001 quality standards.
Further Support
If you have questions about SIPROTEC IEC 61850 interface, please contact your Siemens sales
representative.
SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT 3

C53000-G1140-C211-4, Edition 03.2010
4 SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT
C53000-G1140-C211-4, Edition 03.2010
Table of contents
1 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
1.2 Association model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
1.3 Server model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
1.4 Data set model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
1.5 Substitution model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
1.6 Setting group control model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
1.7 Reporting model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.7.1 Unbuffered Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
1.7.2 Buffered Report . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
1.8 Logging model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
1.9 Generic substation model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
1.10 Transmission of sample values model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
1.11 Control model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.12 Time and time synchronisation model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
1.13 File transfer model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
1.14 General items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.15 TISSUES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
2 Basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
2.2 Effects of Configuration on the Logical Nodes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.2.1 Function parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
2.2.2 Function parameters SIPROTEC 7SJ61 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.2.3 Function parameters SIPROTEC 7SJ62/63/64 . . . . . . . . . . . . . . . . . . . . . . . . . 38
2.2.4 Function parameters SIPROTEC 7SJ80 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
2.2.5 Function parameters SIPROTEC 7SK80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
2.3 Allocation of Logical Nodes to Logical Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
2.4 Logical Node LLN0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2.4.1 Logical Device PROT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
2.4.2 Logical Devices MEAS, DR and EXT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
2.4.3 Logical Device CTRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
2.5 DOI Behavior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
2.5.1 Logical Device PROT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
2.5.2 Logical Devices MEAS, CTRL, DR and EXT. . . . . . . . . . . . . . . . . . . . . . . . . . . 59

C53000-G1140-C211-4, Edition 03.2010
Table of contents
3 Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
3.1 Device (LPHD1, CALH1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

3.1.1 Error with a summary alarm and Alarm summary event . . . . . . . . . . . . . . . . . . . 63
3.2 Oscillographic Fault Records (RDRE1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
3.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2) . . . . . . . . . . . . . . . . . . 68
3.3.1 Overcurrent Protection 50, 51 PH (PTOC6, PTOC7, PTOC1, PTOC18) . . . . . . 68
3.3.2 Overcurrent Protection 50N, 51N (PTOC8, PTOC9, PTOC2) . . . . . . . . . . . . . . 74
3.3.3 Overcurrent Protection 50N, 51N (PTRC2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
3.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3) . . . . . . . . . . . . . . . . . 81
3.4.1 Directional Overcurrent Protection 67 (PTOC10, PTOC11, PTOC3) . . . . . . . . . 81
3.4.2 Directional Overcurrent Protection 67N (PTOC12, PTOC13, PTOC4) . . . . . . . . 85
3.4.3 Directional Overcurrent Protection 67N (PTRC3) . . . . . . . . . . . . . . . . . . . . . . . . 89
3.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17) . . . . . . . . . . . . . . . . . . . 93
3.6 Voltage Protection 27, 59 (PTUVx, PTOVx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
3.6.1 Undervoltage Protection 27 (PTUV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
3.6.2 Undervoltage Protection 27 (PTUV2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
3.6.3 Overvoltage Protection 59 (PTOV1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
3.6.4 Overvoltage Protection 59 (PTOV2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102
3.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5). . . . . . . . . . . . . . . 104
3.8 Motor Protection (PMSS1, PMRI1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
3.8.1 Motor Starting Protection 48 (PMSS1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
3.8.2 Motor Restart Inhibit 66 (PMRI1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
3.9 Load Jam Protection (PMLJ1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
3.10 Frequency protection 81 O/U (PTUFx, PTOFx). . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
3.10.1 Frequency protection 81-1 U (PTUF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113
3.10.5 Frequency protection 81-1 O (PTOF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
3.11 Thermal overload protection (PTTR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
3.12 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx) . . . . . . . . . . . . . . . . . 131
3.12.1 Ground Fault Protection 64 (PHIZ1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
3.12.2 Ground Fault Protection 50N(s) (PSDE1, PSDE2) . . . . . . . . . . . . . . . . . . . . . . . 135
3.12.3 51 N(s) (PSDE3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
3.13 Automatic Reclosing System 79 (RREC1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
3.14 Fault Locator (RFLO1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
3.15 Circuit breaker failure protection 50BF(RBRF1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
3.16 Synchronism and Voltage Check 25 (RSYNx) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
3.17 Three-pole tripping 52 Breaker (XCBR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 158
3.18 Tripping Logic of the Entire Device (PTRC1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162

C53000-G1140-C211-4, Edition 03.2010
Table of contents
3.19 Measurement (MMXU1, MSQI1, MMTR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164

3.19.1 Measures (MMXU1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
3.19.2 Measured values, symmetrical components (MSQI1) . . . . . . . . . . . . . . . . . . . . 169
3.19.3 Power Metering (MMTR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
Literature
Index

C53000-G1140-C211-4, Edition 03.2010
Table of contents

C53000-G1140-C211-4, Edition 03.2010
Applications 1
Contents
This chapter specifies the protocol implementation extra information for testing (PIXIT) of the
IEC 61850 interface in SIPROTEC 7SJ6, 7SJ80, 7SK80.
1.1 General 10
1.2 Association model 11
1.3 Server model 12
1.4 Data set model 13
1.5 Substitution model 14
1.6 Setting group control model 15
1.7 Reporting model 16
1.8 Logging model 19
1.9 Generic substation model 20
1.10 Transmission of sample values model 22
1.11 Control model 23
1.12 Time and time synchronisation model 25
1.13 File transfer model 26
1.14 General items 27
1.15 TISSUES 28

C53000-G1140-C211-4, Edition 03.2010
Applications
1.1 General
1.1 General
This chapter specifies the protocol implementation extra information for testing (PIXIT) of the
IEC 61850 interface in SIPROTEC 7SJ6, 7SJ80, 7SK80.
It is based on the service subset definition given in the protocol implementation conformance
statement (PICS), which is specified within the user manual SIPROTEC 4 Ethernet Module
EN 100 IEC 61850 Electrical Interface 100 MBit, Manual /1/“.
The following applicable ACSI service models are specified:
Association model
Server model
Data set model
Substitution model
Setting group control model
Reporting model
Logging model
Generic substitution model
Transmission of sample values model
Control model
Time and time synchronisation model
File transfer model
General items
Together with the PICS and the MICS the PIXIT forms the basis for a conformance test
according to IEC 61850-10.
The mapping between the IEC 61850 server data model and the SIPROTEC specific data is
specified in Chapter 3.

C53000-G1140-C211-4, Edition 03.2010
Applications
1.2 Association model
1.2 Association model
Description Value / Clarification
Maximum number of clients that can set-up 5 with IEC 61850 Protocol Update
an association simultaneously Version EN100 V04.02 and lower
6 with IEC 61850 Protocol Update

Version EN100 V04.03 and higher
Lost connection detection time range 10 seconds

(default range of TCP_KEEPALIVE is 1 –
20 seconds)
Is authentication supported N
What called association parameters are Transport selector Y

necessary for successful association ? Session selector Y
Presentation selector Y
AP Title ANY
AE Qualifier ANY
Where
Y means: as defined within the ICD-File
ANY means: any value accepted
What is the maximum and minimum MMS Max MMS PDU size 32768
PDU size ? Min MMS PDU size
What is the typical startup time after a 15 SECONDS

power supply interrupt ?
<additional items>

C53000-G1140-C211-4, Edition 03.2010
Applications
1.3 Server model
1.3 Server model
Which analogue value (MX) quality bits are Validity:

supported (can be set by server) ? Y Good,
Y Invalid,
N Reserved,
Y Questionable
Y Overflow
Y OutofRange
N BadReference
N Oscillatory
Y Failure
Y OldData
N Inconsistent
Y Inaccurate
Source:
Y Process
N Substituted
Y Test
Y OperatorBlocked
Which status value (ST) quality bits are Validity:

supported (can be set by server) ? Y Good,
Y Invalid,
N Reserved,
Y Questionable
N BadReference
Y Oscillatory
Y Failure
Y OldData
N Inconsistent
N Inaccurate
Source:
Y Process
Y Substituted
Y Test
Y OperatorBlocked
What is the maximum number of data Not restricted; depends on the max. MMS PDU size given
values in one GetDataValues request ? above.
What is the maximum number of data Not restricted; depends on the max. MMS PDU size given
values in one SetDataValues request ? above. No Data Attribute within our object directory is
writable with the service SetDataValues.
<additional items>

C53000-G1140-C211-4, Edition 03.2010
Applications
1.4 Data set model
1.4 Data set model
Maximum number of data elements in one Not limited by an internal configuration parameter. It
data set depends on the available memory.
How many persistent data sets can be 64 data sets for each LD. It depends on the available
created by one or more clients ? memory.
How many non-persistent data sets can be 10 data sets. It depends on the available memory.
created by one or more clients ?
additional items:
Maximum number of data sets Could not be defined, it depends on the available memory
space. In principle, this information it not necessary from
type conformance testing standpoint.

C53000-G1140-C211-4, Edition 03.2010
Applications
1.5 Substitution model
1.5 Substitution model
This service will not be supported (see also SIPROTEC 4 Ethernet Module EN 100 IEC 61850
Electrical Interface 100 MBit, Manual /1/).

C53000-G1140-C211-4, Edition 03.2010
Applications
1.6 Setting group control model
1.6 Setting group control model
What is the number of supported setting Setting groups available for LLN0 only in LD PROT. The
groups for each logical device ? number of supported setting groups is 1 or 4, it depends
on the given configuration. Specified in the ICD-File.
What is the effect of when and how the Just SelectActiveSG service will supported according to
non-volatile storage is updated ? PICS.
(compare IEC 61850-8-1 $16.2.4)
<additional items>

C53000-G1140-C211-4, Edition 03.2010
Applications
1.7 Reporting model
1.7 Reporting model
1.7.1 Unbuffered Report
The supported trigger conditions are Y Integrity

Y Data change
Y Quality change
Y Data update
Y General Interrogation
The supported optional fields are Y Sequence-number

Y Report-time-stamp
Y Reason-for-inclusion
Y Data-set-name
Y Data-reference
N Buffer-overflow
N EntryID
Y Conf-rev
Y Segmentation
Can the server send segmented reports ? Y
Mechanism on second internal data Send report immediately

change notification of the same analogue
data value within buffer period
(Compare IEC 61850-7-2 $14.2.2.9)
Multi client URCB approach All clients can access all URCB’s
(Compare IEC 61850-7-2 $14.2.1)
additional items:
Interrupt of general interrogation Running GI could not be interrupted. If a new GI request

occurs during a running GI, the current GI will be finished
first before the second GI request will be processed.
Integrity period Configurable >=1 second;
Dynamic URCB reservation after an abort Reservation of the URCB is lost. After a re-establishment
of the client/server association of the association the URCB reservation has to be done
by the client before. This behavior is implemented to
avoid unnecessary memory residuals if temporarily client
associations (e.g. for maintenance) are established.
Configured URCB reservation after an Reservation of the URCB is not lost.

abort of the client/server association

C53000-G1140-C211-4, Edition 03.2010
Applications
1.7 Reporting model
1.7.2 Buffered Report
The supported trigger conditions are Y Integrity

Y Data change
Y Quality change
Y Data update
Y General Interrogation
The supported optional fields are Y Sequence-number

Y Report-time-stamp
Y Reason-for-inclusion
Y Data-set-name
Y Data-reference
Y Buffer-overflow
Y EntryID
Y Conf-rev
Y Segmentation
Can the server send segmented reports ? Y
Mechanism on second internal data Buffer the Entry

change notification of the same analogue Send report if the report is enabled
data value within buffer period
(Compare IEC 61850-7-2 $14.2.2.9)
Multi client BRCB approach All clients can access all BRCB’s
(Compare IEC 61850-7-2 $14.2.1)
What is the format of EntryID ? First 2 Byte : Integer

Last 6 Bytes: BTime6 time stamp
What is the buffer size for each BRCB or About 1 MB are available for the buffering.
how many reports can be buffered ? Each BRCB has an extension attribute Memory that
display the percentage of those 1 MB that have been
reserved/forseen for its own entries.
Default amount 1 MB/(2*Number of logical devices)
additional items:
Interrupt of general interrogation Running GI could not be interrupted. If a new GI request

occurs during a running GI, the current GI will be finished
first before the second GI request will be processed.
Integrity period Configurable >=1 second;
Dynamic BRCB reservation after an abort Reservation of the BRCB has been fixed with TISSUE
of the client/server association 453.
The value of the attribute ResvTms delivers the time
interval during which the reservation is still active after the
connection has been lost. In case a BRCB is still
reserved, and a client connects with the same IP address
as the one used during the reservation, then the BRCB
attribute can be written by this client without prior setting
the ResvTms attribute as long as the reservation timer
has not expired.

C53000-G1140-C211-4, Edition 03.2010
Applications
1.7 Reporting model
Configured BRCB reservation after an Reservation of the BRCB is not lost for BRCBs that have
abort of the client/server association been pre-associated to a specific client (pre-association
defined with means of the CLientLN element with the
BRCB instantiation in the SCD file).
Reservation of a BRCB is lost for BRCBs, that have not
been pre-associated to a specific client, after the
expiration of the reservation timer set with the ResvTms
attribute. In case ResvTms is not set (backward
compatibility), ResvTms will get a default value for all
preconfigured BRCBs that are not pre-associated to a
specific client.
Optional use of a flow control for As specified in the IEC61850-7-2, transmission of entries
transmitting history of a BRCB may required some times, depending of the amount of
entries that have to be transmitted.
Therefore, the SIPROTEC has an optional flow control
feature to accelerate the transmission of the entries: each
BRCB has an extended attribute MaxOutReports that can
be set from the associated-client to change the
transmmision strategy of the entries. The number ordered
will then be transmitted as long as they exist in the buffer;
the server then reset the attribute to 0 and wait for the
client to set it again in order to continue the history
transmission with MaxOutReports entries. The attribute
only influences the flow control of entries while dealing
with the history, and not after the history transmission has
completed.

C53000-G1140-C211-4, Edition 03.2010
Applications
1.8 Logging model
1.8 Logging model

C53000-G1140-C211-4, Edition 03.2010
Applications
1.9 Generic substation model
What is the behavior when one subscribed The telegram will be discarded (i.e not forwarded to the
GOOSE message isn’t received or application) since it is corrupt or syntactically incorrect
syntactically incorrect ? and therefore not readable. The data objects will be
declared as invalid after a timeout detection since no
telegram have been received by the application.
What is the behavior when a subscribed Error message will be stored into the error buffer (could
GOOSE message is out-of-order ? be accessed by EN100 web-server).
All expected data objects will be declared as invalid.
What is the behavior when a subscribed The sequence number given in the GOOSE-message is
GOOSE message is duplicated ? out-of-order. Error message will be stored into the error
buffer (could be accessed by EN100 web-server).
additional items:
Maximum number of GOOSE messages <= 16 ; It depends on the available memory.

which could be sent
Maximum number of GOOSE messages <= 128 ; It depends on the available memory.
which could be received
Interpretation of GOOSE messages at 1. Received GOOSE data objects without assigned

subscriber side quality attribute are interpreted as invalid.
2. Received GOOSE data objects which quality attribute
are set to questionable are changed to invalid.
GOOSE subscriber behavior in case of After a GOOSE multicast application association has
missing GOOSE messages been interrupted, the reception of the second consecutive
GOOSE telegram is required to validate the state of this
GOOSE association again.
However, the IED tolerates a missing telegram as long as
the next telegram (expected n, received n+1) is received
within the time allowed to live time out detection (the time
allowed to live timeout detection occurs after 2*TAL).
GOOSE subscriber behaviour in case of If a message is received twice or more, the IED already
multiple GOOSE messages reports an error after the second reception. Therefore,
network configuration error can be more easily tracked.
What is the behavior when a GOOSE Error message will be stored into the error buffer (could
header parameter is mismatching with the be accessed by EN100 web-server).
expected one? All expected data objects will be declared as invalid.
(datSet, goID, confRev, numDatSetEntries,
number of allData)
What is the behavior when a Error message will be stored into the error buffer (could
timeAllowedToLive is 0? be accessed by EN100 web-server) since the
timeAllowedToLive expired.

C53000-G1140-C211-4, Edition 03.2010
Applications
What is the behavior when there is an out- The confRev attribute in the header guarantees that the
of-order entry in the allData? allData entries are in the correct order. Therefore, it’s
necessary to check the confRev attribute. There is no
chance to detect such an out-of-order.
What is the behavior when no telegram is To avoid an incorrect timeout detection, the subscriber
received within a TAL timeout? detects a timeout after a period of 2×TAL.
The information is then declared as questionable,
oldData.
What is the behavior when a GOOSE Since the goCBRef shall be unique stationwide, the
header parameter goCBRef is mismatching received telegram with the mismatched goCBRef will be
with the expected one? discarted: it has not been published. In that case only the
timeout detection will set the data to invalid.
What is the behavior when a GOOSE The APPID is a link layer parameter. It is used as a filter
header parameter APPID is mismatching on link layer. If the APPID is mismatching, the tellegram
with the expected one? will therefore be discarded on link layer without notifying
the application. Only the timeout detection will set the
data to invalid.
What is the behavior when a GOOSE The t parameter is not checked. Therefore it doesn't lead
header parameter t is not increasing? to any error detection.
What is the behavior when The telegram is discarded since it is corrupt (not well
numDatSetEntries and number of allData formed). After the timeout detection (no telegram
are inconsistent? forwarded to the application) the data objects are
declared invalid.

C53000-G1140-C211-4, Edition 03.2010
Applications
1.10 Transmission of sample values model
1.10 Transmission of sample values model
Compare the “Implementation Guidelines for Electrical Current and Voltage Transducers
according to IEC 60044-7/8 with Digital Output according to IEC 61850-9-2; Version 1.0; as
specified by ABB, Areva, Landis+Gyr, OMICRON and SIEMENS

C53000-G1140-C211-4, Edition 03.2010
Applications
1.11 Control model
1.11 Control model
What control models are supported ? Y Status-only

Y Direct-with-normal-security
N Sbo-with-normal-security
Y Direct-with-enhanced-security
Y Sbo-with-enhanced-security
Is Time activated operate (operTm) N

supported
What is the behavior when the test attribute Will be acknowledged with negative response. The
is set in the SelectWithValue and/or AddCause attribute will be set to “not supported”
Operate request ?
What are the conditions for the time (T) Time attribute is not relevant.
attribute in the SelectWithValue and/or
Operate request ?
Is “operate-many” supported ? N
Is pulse configuration supported ? N
What check conditions are supported ? Y Synchrocheck

Y Interlock-check
What service error types are supported ? Y Instance-not-available

Y Instance-in-use
Y Access-violation
Y Access-not-allowed-in-current-state
Y Parameter-value-inappropriate
Y Parameter-value-inconsistent
Y Class-not-supported
Y Instance-locked-by-other-client
Y Control-must-be-selected
Y Type-conflict
Y Failed-due-to-communications
Y Constraint failed-due-to-server-constraint

C53000-G1140-C211-4, Edition 03.2010
Applications
1.11 Control model
What additional cause diagnosis are N Blocked-by-switching-hierarchy

supported ? Y Select-failed
Y Invalid-position
Y Position-reached
Y Parameter-change-in-execution
Y Step-limit
Y Blocked-by-Mode
Y Blocked-by-process
Y Blocked-by-interlocking
Y Blocked-by-synchrocheck
Y Command-already-in-execution
N Blocked-by-health
Y 1-of-n-control
Y Abortion-by-cancel
Y Time-limit-over
N Abortion-by-trip
Y Object-not-selected
additional items:
What additional cause diagnosis Y Plausibility_error

extensions are supported ? Y Parameter_setting_invalid
Y Hardware_error
Y System_overload
Y Internal_fault
Y Command_sequence_error
Changing the control services by N

configuration
Inconsistency between Select and (Oper or Oper or cancel will be acknowledged with negative
cancel) response if inconsistencies to the select request are
detected.
The following attributes will not be checked in this case:
T (Time)
Cancel request could be sent after an Y

operate request.
Format of the control time stamp attribute ? TimeStamp instead of EntryTime

acc. to the 7-2 Errata List.
Negative response for select request could If test mode is activated or

be performed only If the selection is always done.

C53000-G1140-C211-4, Edition 03.2010
Applications
1.12 Time and time synchronisation model
1.12 Time and time synchronisation model
What kind of quality bits are supported ? N LeapSecondsKnown

Y ClockFailure
Y ClockNotSynchronized
What kind of quality accuracy bits are Y Invalid

supported ? N Unspecified
What is the behavior when the time The quality attribute “ClockFailure” will be set to TRUE
synchronization signal/messages are lost ? after a configured time period.
What is the behaviour when the time A stratum with a value greater than 3 with the SNTP time
synchronisation messages indicate that the synchronization messages indicates that the time server
stratum is greater than 3? has a questionable synchronisation.
It might also indicate that no GPS connection are
available.
Therefore the time quality attribute
“ClockNotSynchronized” will be set to TRUE as long as
the stratum content is greater than 3.
additional items:
What is the behavior at start up time when The “ClockNotSynchronized” attribute is set to TRUE as
a time synchronization via SNTP is long as no time synchronization is established.
configured ?

C53000-G1140-C211-4, Edition 03.2010
Applications
1.13 File transfer model
1.13 File transfer model
What is structure of files and directories? Directory name / COMTRADE / *;

Directory name / LD / *;
Files according to the comtrade standard.
What is the resulting behavior if no file If no file specification is present in the directory request,
specification is present in the file directory all files are returned - not only the files in the root
request? directory.
Is the IETF FTP protocol also implemented ? N
Directory names are separated from the file “/”

name by
The maximum file name size including path 64

(default 64 chars)
Are directory/file name case sensitive Case sensitive
Maximum file size Not limited by implementation or configuration. Depends

on available memory.
additional items:
Maximum number of clients that can use the 1

FTP service simultaneously
Maximum number of files that can be 1

accessed simultaneously

C53000-G1140-C211-4, Edition 03.2010
Applications
1.14 General items
1.14 General items
IED behavior when the Logical Device Unlike the definition of the Data Objects “Mod/Beh” in IEC
is blocked : LLN0.Mod.stVal = blocked 61850-7-4, outputs to the process will be generated.
Details to this behavior are specified in SIPROTEC 4
Ethernet Module EN 100 IEC 61850 Electrical Interface
100 MBit, Manual /1/
additional items:
GOOSE Proxy object To be able to subscribe Data over GOOSE, Proxy

Objects are added into the object directory.
Typically, they are Data of GGIO logical nodes:
SPCSOxx, DPCSOxx, ISCSOxx.
The Data Attributes of those Data are ctlVal, q and t.
The control model associated to those Data is status-only.
They are not controllable from an IEC61850 client, and
their function is only to enable the GOOSE subscribing.
What is the type of the attribute actVal in The type is integer 32 (INT32).
the BCR (Binary Counter Reading) CDC?

C53000-G1140-C211-4, Edition 03.2010
Applications
1.15 TISSUES
1.15 TISSUES
Topic TISSUE Link Description Impact of

-No. Interoper.
Object Model 120 http://www.tissue.iec61850.com/ Type - Mod.stVal and -

tissue.mspx?issueid=120 Mod.ctlVal
146 http://www.tissue.iec61850.com/ CtxInt -

tissue.mspx?issueid=146
173 http://www.tissue.iec61850.com/ Ctl modelling -

tissue.mspx?issueid=173 harmonization
234 http://www.tissue.iec61850.com/ New type CtxInt x

Services 377 http://www.tissue.iec61850.com/ DeleteDataSet response- -

276 http://www.tissue.iec61850.com/ File Services Negative -

tissue.mspx?issueid=276 Responses
183 http://www.tissue.iec61850.com/ GetNameList error x

tissue.mspx?issueid=183 handling
165 http://www.tissue.iec61850.com/ Improper Error Response x

tissue.mspx?issueid=165 for GetDataSetValues
116 http://www.tissue.iec61850.com/ GetNameList with empty x

tissue.mspx?issueid=116 response?
Reporting 474 http://www.tissue.iec61850.com/ GI for URCB -

453 http://www.tissue.iec61850.com/ Reporting & Logging x

tissue.mspx?issueid=453 model revision
438 http://www.tissue.iec61850.com/ EntryTime base should -

tissue.mspx?issueid=438 be GMT
349 http://www.tissue.iec61850.com/ BRCB TimeOfEntry has x

tissue.mspx?issueid=349 two definitions
348 http://www.tissue.iec61850.com/ URCB class and report x


C53000-G1140-C211-4, Edition 03.2010
Applications
1.15 TISSUES
Reporting 344 http://www.tissue.iec61850.com/ TimeOfEntry misspelled -

335 http://www.tissue.iec61850.com/ Clearing of Bufovfl x

332 http://www.tissue.iec61850.com/ Ambiguity in use of x

tissue.mspx?issueid=332 trigger options
329 http://www.tissue.iec61850.com/ Reporting and BufOvl x

322 http://www.tissue.iec61850.com/ Write Configuration

tissue.mspx?issueid=322 attribute of BRCBs
301 http://www.tissue.iec61850.com/ SqNum in Buffered -

tissue.mspx?issueid=301 Reports
300 http://www.tissue.iec61850.com/ Attribute Resv in BRCB x

298 http://www.tissue.iec61850.com/ Type of SqNum x

297 http://www.tissue.iec61850.com/ Sequence number x

278 http://www.tissue.iec61850.com/ EntryId not valid for a x

tissue.mspx?issueid=278 server
275 http://www.tissue.iec61850.com/ Confusing statement on x

tissue.mspx?issueid=275 GI usage
191 http://www.tissue.iec61850.com/ BRCB: Integrity and x

tissue.mspx?issueid=191 buffering reports
190 http://www.tissue.iec61850.com/ BRCB: EntryId and x

tissue.mspx?issueid=190 TimeOfEntry
177 http://www.tissue.iec61850.com/ Ignoring OptFlds bits for -

tissue.mspx?issueid=177 URCB
52 http://www.tissue.iec61850.com/ Ambiguity GOOSE x

tissue.mspx?issueid=52 SqNum
49 http://www.tissue.iec61850.com/ BRCB TimeOfEntry? x

Control Model 46 http://www.tissue.iec61850.com/ Synchro check cancel x

44 http://www.tissue.iec61850.com/ AddCause - Object not x

tissue.mspx?issueid=44 sel
30 http://www.tissue.iec61850.com/ control parameter T x


C53000-G1140-C211-4, Edition 03.2010
Applications
1.15 TISSUES

C53000-G1140-C211-4, Edition 03.2010
Basics 2
Contents
This chapter contains general information about the effects of device configuration on Logical
Nodes and DOIs.
2.1 General 32
2.2 Effects of Configuration on the Logical Nodes 34
2.3 Allocation of Logical Nodes to Logical Devices 49
2.4 Logical Node LLN0 53
2.5 DOI Behavior 58

C53000-G1140-C211-4, Edition 03.2010
Basics
2.1 General
2.1 General
The protocol IEC 61850 was developed to define a standard that can be internationally
employed for the transmission of power automation system data.
This cross national standard enables an interoperability between automation systems and
devices made by different manufacturers.
The devices and high voltage bay control units of the SIPROTEC 4 series can be equipped with
an Ethernet module EN100 via which the protocol IEC 61850 is interpreted.
The configuration of the protocol and the integration of the device with redundant IEC 61850
interfaces in your network are performed via the configuration system DIGSI.
For details please refer to the manuals:
SIPROTEC 4 Ethernet Module EN 100 IEC 61850 Electrical Interface 100 MBit, Manual /1/
and
SIPROTEC 4 System Description /2/.
Note
The following definitions are taken mainly from standard IEC 61850, Technical Specification
IEC TS 61850-2.
Logical Devices
LD Logical Devices represent a functional structuring of the LN Logical Nodes of a SIPROTEC
device.
The following Logical Devices are present:
Logical Device Protection PROT
Logical Device Measurement MEAS
Logical Device Disturbance Recorder DR
Logical Device Control CTRL

Logical Device Extended EXT
Each LD contains LN LLN0 and LN LPHD1.

The allocation of the Logical Nodes to the Logical Devices is listed in Chapter 2.3.

C53000-G1140-C211-4, Edition 03.2010
Basics
2.1 General
Logical Node LN
Smallest part of a function that exchanges data. A logical node is an object defined by its data
and methods.
Data object instance DOI

A Data object is part of a logical node object representing specific information for example status
of measurement. From an object-oriented point of view, a data object is an instance of a data
class. Specific data classes carry the semantic within a logical node.
Data attribute instance DAI

A Data attribute defines the name (semantic), format, range of possible values, and
representation of values while being communicated.
Annunciation types via GOOSE

Generic Object Oriented Substation Event
A GOOSE report enables high speed trip signals to be issued with a high probability of delivery.
The following types of information can be configured via GOOSE.
External single point indication O/O
External single point indication I/O
External double point indication

External double point indication, fast
External operational measured values
External metered values

C53000-G1140-C211-4, Edition 03.2010
Basics
2.2 Effects of Configuration on the Logical Nodes
2.2.1 Function parameters
Depending on the configuration of the function parameters the functions of the SIPROTEC are
enabled or disabled. If a function is disabled, the corresponding Logical Node is not available.
The following Logical Nodes are always available:
Logical Device Protection: LLN0, LPHD1, XCBR1,

PTRC1
Logical Device Measurement: LLN0, LPHD1, MMXU1,
MMTR1, MSQI1
Logical Device Control: LLN0, LPHD1, CALH1

C53000-G1140-C211-4, Edition 03.2010
Basics
2.2.2 Function parameters SIPROTEC 7SJ61
The following table shows which Logical Nodes are available when setting the corresponding
function parameter.
The setting (-) implies that no corresponding LN is available.
Table 2-1 SIPROTEC 7SJ61 - Effects of Function parameters to the Logical Nodes
No. Function Setting Logical Nodes
103 Setting Group Change Option No effect
104 Oscillographic Fault Records Disabled -
Enabled RDRE1
112 50/51 (Charac. Phase) Disabled -

Definite Time PTOC6, PTOC7,
PTOC18, PTRC2
TOC IEC PTOC6, PTOC7, PTOC1

PTOC18, PTRC2
TOC ANSI PTOC6, PTOC7,

PTOC1, PTOC18,
PTRC2
User Defined PU PTOC6, PTOC7, PTOC1

PTOC18, PTRC2
Userdef. Reset PTOC6, PTOC7, PTOC1,

PTOC18, PTRC2
113 50N/51N (Charac. Ground) Disabled -

Definite Time PTOC8, PTOC9, PTRC2
TOC IEC PTOC8, PTOC9, PTOC2,

PTRC2
TOC ANSI PTOC8, PTOC9, PTOC2,

PTRC2
User Defined PU PTOC8, PTOC9, PTOC2,

PTRC2

PTRC2
117 Cold Load Pickup No effect

C53000-G1140-C211-4, Edition 03.2010
Basics
Table 2-1 SIPROTEC 7SJ61 - Effects of Function parameters to the Logical Nodes (Forts.)
122 2nd Harmonic Inrush Restraint No effect
127 50 1Ph Disabled -

Single Phase Overcurrent Protection
Enabled PTOC16, PTOC17
131 (sens.) Ground fault Disabled -
Enabled PHIZ1, PSDE1, PSDE2
133 Intermittent earth fault protection No effect
140 46 Negative Sequence Protection Disabled -
TOC ANSI / TOC IEC PTOC14, PTOC15,

PTOC5
Definite Time PTOC14, PTOC15
141 48 Startup Supervision of Motors Disabled -
Enabled PMSS1
142 49 Thermal Overload Protection Disabled -
No ambient temp PTTR1
With amb. temp. PTTR1
143 66 Startup Counter for Motors Disabled -
Enabled PMRI1
144 Load Jam Protection Disabled -
Enabled PMLJ1
170 50BF Breaker Failure Protection Disabled -
Enabled RBRF1
enabled w/ 3I0> RBRF1
171 79 Auto-Reclose Function Disabled -
Enabled RREC1
172 52 Breaker Wear Monitoring No effect

C53000-G1140-C211-4, Edition 03.2010
Basics
182 74TC Trip Circuit Supervision Disabled -
2 Binary Inputs DOI CirSpv, LN XCBR

LD PROT
1 Binary Input DOI CirSpv, LN XCBR

LD PROT
190 External Temperature Input No effect
191 Ext. Temperature Input Connection Type No effect

C53000-G1140-C211-4, Edition 03.2010
Basics
2.2.3 Function parameters SIPROTEC 7SJ62/63/64
function parameter.
Table 2-2 SIPROTEC 7SJ62/63/64 - Effects of Function parameters to the Logical Nodes
Enabled RDRE1

PTOC18, PTRC2

PTOC18, PTRC2

PTOC1, PTOC18,
PTRC2
User Defined PU PTOC6, PTOC7, PTOC1

PTOC18, PTRC2

PTOC18, PTRC2


PTRC2

PTRC2
User Defined PU PTOC8, PTOC9, PTOC2,

PTRC2

PTRC2

C53000-G1140-C211-4, Edition 03.2010
Basics
Table 2-2 SIPROTEC 7SJ62/63/64 - Effects of Function parameters to the Logical Nodes (Forts.)
115 67, 67-TOC Disabled -

Directional Overcurrent Protection
PTRC3
TOC IEC PTOC10, PTOC11,

PTOC3, PTRC3

PTOC3, PTRC3
User Defined PU PTOC10, PTOC11,

PTOC3, PTRC3
Userdef. Reset PTOC10, PTOC11,

PTOC3, PTRC3
116 67N, 67N-TOC Disabled -

PTRC3

PTOC4, PTRC3

PTOC4, PTRC3
User Defined PU PTOC12, PTOC13,

PTOC4, PTRC3
Userdef. Reset PTOC12, PTOC13,

PTOC4, PTRC3

130 (sens.) Ground fault dir. characteristic cos ϕ / sin ϕ see Parameter 131
V0/I0 ϕ mea. see Parameter 131

C53000-G1140-C211-4, Edition 03.2010
Basics
131 (sensitive) Ground fault Disabled -

and
(sens.) Ground fault dir. characteristic = Definite Time PHIZ1, PSDE1, PSDE2
cos ϕ / sin ϕ
TOC IEC PHIZ1, PSDE2, PSDE3
TOC IANSI PHIZ1, PSDE2, PSDE3
User Defined PU PHIZ1, PSDE2, PSDE3
Log. inverse 1 PHIZ1, PSDE2, PSDE3
Log. inverse 2 PHIZ1, PSDE2, PSDE3

and
V0/I0 ϕ mea.
133 Intermittent earth fault protection No effect

PTOC5

PTOC5
Enabled PMSS1
Enabled PMRI1
Enabled PMLJ1

C53000-G1140-C211-4, Edition 03.2010
Basics
150 27, 59 Under/Overvoltage Protection Disabled -
Enabled PTUV1, PTUV2,

PTOV1, PTOV2
154 81 Over/Underfrequency Protection Disabled -
Enabled PTOF1 – PTOF4,

PTUF1 – PTUF4
161 25 Function group 1 Disabled -

Synchronism and Voltage Check
ASYN/SYNCHRON RSYN1
SYNCHROCHECK RSYN1

ASYN/SYNCHRON RSYN2
SYNCHROCHECK RSYN2

ASYN/SYNCHRON RSYN3
SYNCHROCHECK RSYN3

ASYN/SYNCHRON RSYN4
SYNCHROCHECK RSYN4
Enabled RBRF1
Enabled RREC1
180 Fault Locator Disabled -
Enabled RFLO1

C53000-G1140-C211-4, Edition 03.2010
Basics
181 Line sections for fault locator No effect

LD PROT

LD PROT

C53000-G1140-C211-4, Edition 03.2010
Basics
2.2.4 Function parameters SIPROTEC 7SJ80
function parameter.
Table 2-3 SIPROTEC 7SJ80 - Effects of Function parameters to the Logical Nodes
Enabled RDRE1

PTOC18, PTRC2

PTOC18, PTRC2

PTOC1, PTOC18,
PTRC2


PTRC2

PTRC2
115 67, 67-TOC Disabled -

PTRC3

PTOC3, PTRC3

PTOC3, PTRC3

C53000-G1140-C211-4, Edition 03.2010
Basics

PTRC3

PTOC4, PTRC3

PTOC4, PTRC3


and
cos ϕ / sin ϕ

and
V0/I0 ϕ mea.

PTOC5

PTOC5

C53000-G1140-C211-4, Edition 03.2010
Basics

PTOV1, PTOV2

PTUF1 – PTUF4

SYNCHROCHECK RSYN1
Enabled RBRF1
Enabled RREC1
180 Fault Locator Disabled -
Enabled RFLO1
181 Line sections for fault locator 1 Section No effect

2 Sections
3 Sections

LD PROT

LD PROT
192 Capacitive voltage measurement No effect
617 Port B usage No effect

C53000-G1140-C211-4, Edition 03.2010
Basics
2.2.5 Function parameters SIPROTEC 7SK80
function parameter.
Table 2-4 SIPROTEC 7SK80 - Effects of Function parameters to the Logical Nodes
Enabled RDRE1

PTOC18, PTRC2

PTOC18, PTRC2

PTOC1, PTOC18,
PTRC2


PTRC2

PTRC2

PTRC3

PTOC4, PTRC3

PTOC4, PTRC3

C53000-G1140-C211-4, Edition 03.2010
Basics
Table 2-4 SIPROTEC 7SK80 - Effects of Function parameters to the Logical Nodes (Forts.)

and
cos ϕ / sin ϕ

and
V0/I0 ϕ mea.

PTOC5

PTOC5
Enabled PMSS1
Enabled PMRI1
Enabled PMLJ1

C53000-G1140-C211-4, Edition 03.2010
Basics
Table 2-4 SIPROTEC 7SK80 - Effects of Function parameters to the Logical Nodes (Forts.)

PTOV1, PTOV2

PTUF1 – PTUF4
Enabled RBRF1

LD PROT

LD PROT
192 Capacitive voltage measurement No effect
617 Port B usage No effect

C53000-G1140-C211-4, Edition 03.2010
Basics
2.3 Allocation of Logical Nodes to Logical Devices
All Logical Nodes (LN) are allocated to Logical Devices (LD). The following tables show this
allocation and the DOIs available for each LN.
LD PROT
The Logical Device PROT (Protection) contains the following LNs:
Table 2-5 LD PROT - Logical Nodes
LN Function DOI
LLN0 General Mod, Beh, Health, NamPlt, OpTmh
PTRC1 General device pickup Mod, Beh, Health, NamPlt, Str,Tr,FinTr

General OFF
XCBR1 52 Breaker Mod, Beh, Health, NamPlt, Loc, OpCnt, Pos

Three-pole tripping BlkOpn, BlkCls, CBOpCap
SumSwARs1, SumSwARs2, SumSwARs3
PTOC6 50/51 (Charac. Phase) Mod, Beh, Health, NamPlt, Str, Op, ChgSet
PTOC7
PTOC1
PTOC18
PTRC2
PTOC8 50N/51N (Charac. Ground) Mod, Beh, Health, NamPlt, Str, Op, ChgSet
PTOC9
PTOC2
PRTC2
PTOC10 67, 67-TOC Mod, Beh, Health, NamPlt, Str, Op, ChgSet
PTOC11
PTOC3
PTRC3
PTOC12 67N, 67N-TOC Mod, Beh, Health, NamPlt, Str, Op, ChgSet
PTOC13
PTOC4
PRTC2
PTOC16 50 1Ph Mod, Beh, Health, NamPlt, Str, Op

PTOC17
PTUV1 27 Undervoltage Protection Mod, Beh, Health, NamPlt, Str, Op

PTUV2
PTOV1 59 Overvoltage Protection Mod, Beh, Health, NamPlt, Str, Op

PTOV2

C53000-G1140-C211-4, Edition 03.2010
Basics
Table 2-5 LD PROT - Logical Nodes (Forts.)
LN Function DOI
PTOC14 46 Negative Sequence Protection Mod, Beh, Health, NamPlt, Str, Op

PTOC15
PTOC5
PMSS1 48 Startup Supervision of Motors Mod, Beh, Health, NamPlt, Str, Op
PMRI1 66 Startup Counter for Motors Mod, Beh, Health, NamPlt, Op, StrInhTmm
PMLJ1 Load Jam Protection Mod, Beh, Health, NamPlt, Str, Op, LDJamAlm,
ChgSet
PTUF1 81 Underfrequency Protection Mod, Beh, Health, NamPlt, Str, Op, BlkV
PTUF2
PTUF3
PTUF4
PTOF1 81 Overfrequency Protection Mod, Beh, Health, NamPlt, Str, Op, BlkV
PTOF2
PTOF3
PTOF4
PTTR1 49 Thermal Overload Protection Mod, Beh, Health, NamPlt, Str, Op, AlmThm
PSDE1 (sensitive) Ground fault Mod, Beh, Health, NamPlt, Str, Op

PSDE2
PSDE3
PHIZ1 (sensitive) Ground fault Mod, Beh, Health, NamPlt, Str, Op
RREC1 79 Auto-Reclose Function Mod, Beh, Health, NamPlt, Op, AutoRecSt
RFLO1 Fault Locator Mod, Beh, Health, NamPlt, FltZ, FltDiskm, FltDisPrc
RBRF1 50BF Breaker Failure Protection Mod, Beh, Health, NamPlt, Str, OpEx, OpIn
LPHD1 Device PhyNam, PhyHealth, Proxy

C53000-G1140-C211-4, Edition 03.2010
Basics
LD MEAS
The Logical Device MEAS (Measurement) contains the following LNs:
Table 2-6 LD MEAS - Logical Nodes
LN Function DOIs
LLN0 General Mod, Beh, Health, NamPlt
MMXU1 Operational measured values Mod, Beh, Health, NamPlt,

TotW, TotVAr, TotVA, TotPF, Hz, PPV, PhV, A
MMTR1 Power Metering Mod, Beh, Health, NamPlt,

SupWh, SupVArh, DmdWh, DmdVArh
MSQI1 Measured values, symmetrical Mod, Beh, Health, NamPlt, SeqA, SeqV
components
LD DR
The Logical Device DR (Disturbance Recorder) contains the following LNs:
Table 2-7 LD DR - Logical Nodes
LN Function DOIs
LLN0 General Mod, Beh, Health, NamPlt
RDRE1 Oscillographic Fault Records Mod, Beh, Health, NamPlt, RcdMade, RcdStr
FltNum, GriFltNum

C53000-G1140-C211-4, Edition 03.2010
Basics
LD CTRL
The Logical Device CTRL (Control) contains the following LNs:
Table 2-8 LD CTRL - Logical Nodes
LN Function DOIs
LLN0 General Mod, Beh, Health, NamPlt, LEDRs, Loc
RSYN1 25 Function group 1 Mod, Beh, Health, NamPlt,

RSYN2 25 Function group 2 Rel, VInd, AngInd, HzInd, SynPrg,
RSYN3 25 Function group 3 DifVClc, DifHzClc, DifAngClc
RSYN4 25 Function group 4
CALH1 Error with a summary alarm and Mod, Beh, Health, NamPlt, GrAlm, GrWrn,
Alarm summary event ErrBoard1, ErrBoard2, ErrBoard3, ErrBoard4,
ErrBoard5, ErrBoard6, ErrBoard7
LPHD1 Device PhyNam, PhyHealth, Proxy, CtlNum, DevStr
LD EXT
The Logical Device EXT (Extended) contains the following LNs:
Table 2-9 LD EXT - Logical Nodes
LN Function DOIs
LLN0 General Mod, Beh, Health, NamPlt, LEDRs, Loc
LPHD1 Device PhyNam, PhyHealth, Proxy, CtlNum
The Logical Nodes of the switching (and userdefined) objects will be created by DIGSI during
the parameterization of your SIPROTEC device.
MICS, Model Implementation Conformance Statement, shows the assignment of the DOIs;
you can use DIGSI to print the MICS.

C53000-G1140-C211-4, Edition 03.2010
Basics
2.4 Logical Node LLN0
2.4.1 Logical Device PROT
LLN0.Mod
No. Information
52 At Least 1 Protection Funct. is Active (ProtActive) 0 1 1 1 1
Test mode (Test mode) x 0 0 1 1
Stop data transmission (DataStop) x 0 1 0 1
LLN0.Mod.stVal 5 1 2 3 4
device annunciation / setting: 1 - ON / TRUE IEC Status Mod.stVal: 1 - ON

0 - OFF / FALSE 2 - BLOCKED
x - irrelevant 3 - TEST
4 - TEST/BLOCKED
5 - OFF
LLN0.Beh
No. Information
52 At Least 1 Protection Funct. is Active (ProtActive) 0 1 1 1 1
LLN0.Beh.stVal 5 1 2 3 4
device annunciation / setting: 1 - ON / TRUE IEC Status Beh.stVal: 1 - ON

4 - TEST/BLOCKED
5 - OFF
LLN0.Health
No. Information
51 Device is Operational and Protecting (Device OK) 0 1
LLN0.Health.stVal 3 1
device annunciation: 1 - ON IEC Status Health.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Basics
LLN0.OpTmh
No. Information Value
1020 Counter of operating hours (Op.Hours=) LLN0.OpTmh.stVal Operating hours (Absolute value)

C53000-G1140-C211-4, Edition 03.2010
Basics
2.4.2 Logical Devices MEAS, DR and EXT
LLN0.Mod
No. Information
51 Device is Operational and Protecting (Device OK) x x x x
Test mode (Test mode) 1 1 0 0
Stop data transmission (DataStop) 1 0 1 0
LLN0.Mod.stVal 4 3 2 1

4 - TEST/BLOCKED
5 - OFF
LLN0.Beh
No. Information
51 Device is Operational and Protecting (Device OK) 0 1 1 1 1

4 - TEST/BLOCKED
5 - OFF
LLN0.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Basics
LLN0.OpTmh
2.4.3 Logical Device CTRL
LLN0.Mod
No. Information
55 Reset Device (Reset Device) 1 1 1 1 1
Test mode (Test mode) 1 1 0 0 0
Stop data transmission (DataStop) 1 0 1 0 0
LLN0.Mod.stVal 4 3 2 1 5

4 - TEST/BLOCKED
5 - OFF
LLN0.Beh
No. Information
55 Reset Device (Reset Device) 1 1 1 1 1
Test mode (Test mode) 1 1 0 0 0
Stop data transmission (DataStop) 1 0 1 0 0

4 - TEST/BLOCKED
5 - OFF

C53000-G1140-C211-4, Edition 03.2010
Basics
LLN0.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
LLN0.OpTmh

C53000-G1140-C211-4, Edition 03.2010
Basics
2.5 DOI Behavior
2.5 DOI Behavior
2.5.1 Logical Device PROT
For the Logical Nodes of the PROT Logical Device, LNx.Beh.stVal is formed from
LNx.Mod.stVal of the Logical Node and the status of the following device messages:
Test mode (Test mode),
Stop data transmission and
At Least 1 Protection Funct. is Active.
No. Information
Test mode (Test mode) x 0 1 0 1 0 1 x
Stop data transmission (DataStop) x 0 0 1 1 x x x
52 At Least 1 Protection Funct. is Active (ProtActive) x 1 1 1 1 1 1 0
LNx .Mod.stVal 5 1 1 1 1 2 2 x
LNx.Beh.stVal 5 1 3 2 4 2 4 5
device annunciation / setting: 1 - ON / TRUE IEC Status stVal: 1 - ON

4 - TEST/BLOCKED
5 - OFF

C53000-G1140-C211-4, Edition 03.2010
Basics
2.5 DOI Behavior
2.5.2 Logical Devices MEAS, CTRL, DR and EXT
For the Logical Nodes of the MEAS, CTRL, DR and EXT Logical Devices, LNx.Beh.stVal is
formed from LNx.Mod.stVal of the Logical Node and the status of the following device
messages:
Test mode (Test mode),
Stop data transmission.
No. Information
Test mode (Test mode) x 0 1 0 1 0 1
Stop data transmission (DataStop) x 0 0 1 1 x x
LNx .Mod.stVal 5 1 1 1 1 2 2
LNx.Beh.stVal 5 1 3 2 4 2 4
device annunciation / setting: 1 - ON / TRUE IEC Status stVal: 1 - ON

4 - TEST/BLOCKED
5 - OFF

C53000-G1140-C211-4, Edition 03.2010
Basics
2.5 DOI Behavior

C53000-G1140-C211-4, Edition 03.2010
Mapping 3
Contents
This chapter shows the mapping of the information relevant to the device on the Logical Node of
protocol IEC61850. It is structured according to function. In Chapter 2 you can find what
consequences non-configured functions have on the Logical Nodes as well as general
information about IEC 61850 mapping of information.
3.1 Device (LPHD1, CALH1) 62
3.2 Oscillographic Fault Records (RDRE1) 66
3.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2) 68
3.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3) 81
3.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17) 93
3.6 Voltage Protection 27, 59 (PTUVx, PTOVx) 96
3.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5) 104
3.8 Motor Protection (PMSS1, PMRI1) 108
3.9 Load Jam Protection (PMLJ1) 111
3.10 Frequency protection 81 O/U (PTUFx, PTOFx) 113
3.11 Thermal overload protection (PTTR1) 129
3.12 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx) 131
3.13 Automatic Reclosing System 79 (RREC1) 140
3.14 Fault Locator (RFLO1) 142
3.15 Circuit breaker failure protection 50BF(RBRF1) 144
3.16 Synchronism and Voltage Check 25 (RSYNx) 146
3.17 Three-pole tripping 52 Breaker (XCBR1) 158
3.18 Tripping Logic of the Entire Device (PTRC1) 162
3.19 Measurement (MMXU1, MSQI1, MMTR1) 164

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.1 Device (LPHD1, CALH1)
LPHD1.DevStr
No. Information
56 Initial Start of Device (Initial Start) 0 0 1 1
67 Resume (Resume) 0 1 0 1
LPHD1.DevStr.stVal T 2 1 T
device annunciation: 1 - ON IEC Status DevStr.stVal: 1 - Initial Start

0 - OFF 2 - Resume
T - toggel between 1 and 2
LPHD1.Proxy
No. Information
55 Reset Device (Reset Device) 0 1
LPHD1.Proxy.stVal 1 0
device annunciation: 1 - ON IEC Status Proxy.stVal: 0 - DEVICE is not a PROXY

0 - OFF 1 - DEVICE is a PROXY
LPHD1.PhyHealth
No. Information
LPHD1.PhyHealth.stVal 3 1
device annunciation: 1 - ON IEC Status PhyHealth.stVal: 1 - OK

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.1.1 Error with a summary alarm and Alarm summary event
CALH1.Mod
No. Information
CALH1.Mod.stVal 1 5
device annunciation: 1 - ON IEC Status Mod.stVal: 1 - ON

0 - OFF 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF
CALH1.Health
No. Information
CALH1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
CALH1.GrAlm
No. Information
140 Error with a summary alarm (Error Sum Alarm) 1 0
CALH1.GrAlm.stVal 1 0
device annunciation: 1 - ON IEC Status GrAlm.stVal: 0 - FALSE

0 - OFF 1 - TRUE
CALH1.GrWrn
No. Information
160 Alarm Summary Event (Alarm Sum Event) 1 0
CALH1.GrWrn.stVal 1 0
device annunciation: 1 - ON IEC Status GrWrn.stVal: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
The LN CALH1.ErrBoard1 to CALH1.ErrBoard7 are available with Firmware

7SJ61 V4.71 and higher, 7SJ62 V4.71 and higher, 7SJ64 V4.71 and higher,
7SJ80 V4.61 and higher, 7SK80 V4.61 and higher
CALH1.ErrBoard1
No. Information
183 Error Board 1 (Error Board 1) 1 0
CALH1.ErrBoard1.stVal 1 0
device annunciation: 1 - ON IEC Status ErrBoard1.stVal: 0 - FALSE

0 - OFF 1 - TRUE
CALH1.ErrBoard2
No. Information

0 - OFF 1 - TRUE
CALH1.ErrBoard3
No. Information

0 - OFF 1 - TRUE
CALH1.ErrBoard4
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
CALH1.ErrBoard5
No. Information

0 - OFF 1 - TRUE
CALH1.ErrBoard6
No. Information

0 - OFF 1 - TRUE
CALH1.ErrBoard7
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.2 Oscillographic Fault Records (RDRE1)
RDRE1.Mod
No. Information
55 Reset Device (Reset Device) x
RDRE1.Mod.stVal 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
RDRE1.Health
No. Information
RDRE1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
RDRE1.RcdMade
No. Information
30053 Fault recording is running (Fault rec. run.) 0 1
RDRE1.RcdMade.stVal 1 0
device annunciation: 1 - ON IEC Status RcdMade.stVal: 0 - FALSE

0 - OFF 1 - TRUE
(Recording complete)

C53000-G1140-C211-4, Edition 03.2010
Mapping
RDRE1.FltNum
302 Fault Event (Fault Event) RDRE1.FltNum.stVal Present fault number
RDRE1.GriFltNum
301 Power System fault (Pow.Sys.Flt.) RDRE1.GriFltNum.stVal Network fault number
RDRE1.RcdStr
No. Information
30053 Fault recording is running (Fault rec. run.) 0 1
RDRE1.RcdStr.stVal 0 1
device annunciation: 1 - ON IEC Status RcdStr.stVal: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.3 Overcurrent Protection 50, 51, 50N, 51N (PTOCx, PTRC2)
3.3.1 Overcurrent Protection 50, 51 PH (PTOC6, PTOC7, PTOC1, PTOC18)
PTOC6.Mod
No. Information
1753 50/51 O/C is ACTIVE (50/51 PH ACT) x x x x x
1752 50/51 O/C is BLOCKED (50/51 PH BLK) x x x 1 0
1751 50/51 O/C switched OFF (50/51 PH OFF) 1 x 0 0 0
50-1 PICKUP (P1204) = ∞ x 1 0 0 0
Frequency range is exceeded x x 1 x 0
PTOC6.Mod.stVal 5 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PTOC6.Health
No. Information
PTOC6.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PTOC6.Str
No. Information
1810 50-1 picked up (50-1 picked up) 0 1
PTOC6.Str.general 0 1
device annunciation: 1 - ON IEC Status Str.general: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC6.Op
No. Information
1815 50-1 TRIP (50-1 TRIP) 0 1
PTOC6.Op.general 0 1
device annunciation: 1 - ON IEC Status Op.general: 0 - FALSE

0 - OFF 1 - TRUE
PTOC6.ChgSet
No. Information
1997 Dynamic settings are ACTIVE (Dyn set. ACTIVE) 0 1
PTOC6.ChgSet.stVal 0 1
device annunciation: 1 - ON IEC Status ChgSet.stVal: 0 - FALSE

0 - OFF 1 - TRUE
PTOC7.Mod
No. Information
50-2 PICKUP (P1202) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC7.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC7.Str
No. Information

0 - OFF 1 - TRUE
PTOC7.Op
No. Information
1805 50-2 TRIP (50-2 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC7.ChgSet
No. Information

0 - OFF 1 - TRUE
PTOC1.Mod
No. Information
51 PICKUP (P1207) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC1.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC1.Str
No. Information
1820 51 picked up (51 picked up) 0 1

0 - OFF 1 - TRUE
PTOC1.Op
No. Information
1825 51 TRIP (51 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC1.ChgSet
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC18.Mod
No. Information
50-3 PICKUP(P1217) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC18.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC18.Str
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC18.Op
No. Information
1769 50-3 TRIP (50-3 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC18.ChgSet
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.3.2 Overcurrent Protection 50N, 51N (PTOC8, PTOC9, PTOC2)
PTOC8.Mod
No. Information
7158 50N/51N is ACTIVE (50N/51N ACT) x x x x x
7157 50N/51N is BLOCKED (50N/51N BLK) x x x 1 0
7156 50N/51N is OFF (50N/51N OFF) 1 x 0 0 0
50N-1 PICKUP (P1304) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC8.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC8.Str
No. Information
1834 50N-1 picked up (50N-1 picked up) 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC8.Op
No. Information
1836 50N-1 TRIP (50N-1 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC8.ChgSet
No. Information

0 - OFF 1 - TRUE
PTOC9.Mod
No. Information
7156 50N/51N is OFF (50N/51N OFF) 1 x 0 0 0
50N-2 PICKUP (P1302) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC9.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC9.Str
No. Information

0 - OFF 1 - TRUE
PTOC9.Op
No. Information
1833 50N-2 TRIP (50N-2 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC9.ChgSet
No. Information

0 - OFF 1 - TRUE
PTOC2.Mod
No. Information
7156 50N/51N is OFF (50N/51N OFF) 1 x 0 0 0
51N PICKUP (P1307) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC2.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC2.Str
No. Information
1837 51N picked up (51N picked up) 0 1

0 - OFF 1 - TRUE
PTOC2.Op
No. Information
1839 51N TRIP (51N TRIP) 0 1

0 - OFF 1 - TRUE
PTOC2.ChgSet
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.3.3 Overcurrent Protection 50N, 51N (PTRC2)
PTRC2.Mod
No. Information
1753 50/51 O/C is ACTIVE (50/51 PH ACT) or x x x x

1758 50N/51N is ACTIVE (50N/51N ACT)
1752 50/51 O/C is BLOCKED (50/51 PH BLK) and x x 1 0

1757 50N/51N is BLOCKED (50N/51N BLK)
1751 50/51 O/C switched OFF (50/51 PH OFF) and 1 0 0 0

1756 50N/51N is OFF (50N/51N OFF)
Frequency range is exceeded x 1 x 0
PTRC2.Mod.stVal 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PTRC2.Health
No. Information
PTRC2.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PTRC2.Str
No. Information
1761 50(N)/51(N) O/C PICKUP (50(N)/51(N) PU) 0 1
PTRC2.Str.general 0 1

0 - OFF 1 - TRUE
PTRC2.Str.dirGeneral
No. Information
PTRC2.Str.dirGeneral 0
device annunciation: IEC Status Str.dirGeneral: 0 - UNKNOWN

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTRC2.Str.phsA
No. Information
1762 50/51 Phase A picked up (50/51 Ph A PU) 0 1
PTRC2.Str.phsA 0 1
device annunciation: 1 - ON IEC Status Str.phsA: 0 - FALSE

0 - OFF 1 - TRUE
PTRC2.Str.dirPhsA
No. Information
PTRC2.Str.dirPhsA 0
device annunciation: IEC Status Str.dirPhsA: 0 - UNKNOWN
PTRC2.Str.phsB
No. Information
1763 50/51 Phase B picked up (50/51 Ph B PU) 0 1
PTRC2.Str.phsB 0 1
device annunciation: 1 - ON IEC Status Str.phsB: 0 - FALSE

0 - OFF 1 - TRUE
PTRC2.Str.dirPhsB
No. Information
PTRC2.Str.dirPhsB 0
device annunciation: IEC Status Str.dirPhsB: 0 - UNKNOWN
PTRC2.Str.phsC
No. Information
1764 50/51 Phase C picked up (50/51 Ph C PU) 0 1
PTRC2.Str.phsC 0 1
device annunciation: 1 - ON IEC Status Str.phsC: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTRC2.Str.dirPhsC
No. Information
PTRC2.Str.dirPhsC 0
device annunciation: IEC Status Str.dirPhsC: 0 - UNKNOWN
PTRC2.Str.neut
No. Information
1765 50N/51N picked up (50N/51NPickedup) 0 1
PTRC2.Str.neut 0 1
device annunciation: 1 - ON IEC Status Str.neut: 0 - FALSE

0 - OFF 1 - TRUE
PTRC2.Str.dirNeut
No. Information
PTRC2.Str.dirNeut 0
device annunciation: IEC Status Str.dirPhsC: 0 - UNKNOWN
PTRC2.Op
No. Information
1791 50(N)/51(N) TRIP (50(N)/51(N)TRIP) 0 1
PTRC2.Op.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.4 Directional Overcurrent Protection 67, 67N (PTOCx, PTRC3)
3.4.1 Directional Overcurrent Protection 67 (PTOC10, PTOC11, PTOC3)
PTOC10.Mod
No. Information
2653 67/67-TOC is ACTIVE (67 ACTIVE) x x x x x
2652 67/67-TOC is BLOCKED (67 BLOCKED) x x x 1 0
2651 67/67-TOC switched OFF (67/67-TOC OFF) 1 x 0 0 0
67-1 PICKUP (P1504) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC10.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC10.Str
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC10.Op
No. Information
2665 67-1 TRIP (67-1 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC10.ChgSet
No. Information

0 - OFF 1 - TRUE
PTOC11.Mod
No. Information
67-2 PICKUP (P1502) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC11.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC11.Str
No. Information

0 - OFF 1 - TRUE
PTOC11.Op
No. Information
2649 67-2 TRIP (67-2 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC11.ChgSet
No. Information

0 - OFF 1 - TRUE
PTOC3.Mod
No. Information
67-TOC PICKUP (P1507) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC3.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC3.Str
No. Information
2670 67-TOC picked up (67-TOC picked up) 0 1

0 - OFF 1 - TRUE
PTOC3.Op
No. Information
2675 67-TOC TRIP (67-TOC TRIP) 0 1

0 - OFF 1 - TRUE
PTOC3.ChgSet
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.4.2 Directional Overcurrent Protection 67N (PTOC12, PTOC13, PTOC4)
PTOC12.Mod
No. Information
2658 67N/67N-TOC is ACTIVE (67N ACTIVE) x x x x x
2657 67N/67N-TOC is BLOCKED (67N BLOCKED) x x x 1 0
2656 67N/67N-TOC switched OFF (67N OFF) 1 x 0 0 0
67N-1 PICKUP (P1604) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC12.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC12.Str
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC12.Op
No. Information
2683 67N-1 TRIP (67N-1 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC12.ChgSet
No. Information

0 - OFF 1 - TRUE
PTOC13.Mod
No. Information
67N-2 PICKUP (P1602) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC13.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC13.Str
No. Information

0 - OFF 1 - TRUE
PTOC13.Op
No. Information
2679 67N-2 TRIP (67N-2 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC13.ChgSet
No. Information

0 - OFF 1 - TRUE
PTOC4.Mod
No. Information
M.of PU TD (P1630) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC4.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC4.Str
No. Information
2684 67N-TOC picked up (67N-TOCPickedup) 0 1

0 - OFF 1 - TRUE
PTOC4.Op
No. Information
2686 67N-TOC TRIP (67N-TOC TRIP) 0 1

0 - OFF 1 - TRUE
PTOC4.ChgSet
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.4.3 Directional Overcurrent Protection 67N (PTRC3)
PTRC3.Mod
No. Information
67/67-TOC is ACTIVE (67 ACTIVE) (I 2653) or x x x x

67N/67N-TOC is ACTIVE (67N ACTIVE) (I 2658)
67/67-TOC is BLOCKED (67 BLOCKED) (I 2652) and x x 1 0

67N/67N-TOC is BLOCKED (67N BLOCKED) (I 2657)
67/67-TOC switched OFF (67/67-TOC OFF) (I 2651) and 1 0 0 0

67N/67N-TOC switched OFF (67N OFF) (I 2656)
PTRC3.Mod.stVal 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PTRC3.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTRC3.Str
No. Information
2691 67/67N picked up (67/67N pickedup) 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTRC3.Str.dirGeneral
No. Information
2691 67/67N picked up (67/67N picked up) 0 1 1 1 1
Phase A forward (Phase A forward) (I 2628) or x 0 1 0 1

Phase B forward (Phase B forward) (I 2629) or
Phase C forward (Phase C forward) (I 2630) or
Ground forward (Ground forward) (I 2635)
Phase A reverse (Phase A reverse) (I 2632) or x 0 0 1 1

Phase B reverse (Phase B reverse) (I 2633) or
Phase C reverse (Phase C reverse) (I 2634) or
Ground reverse (Ground reverse) (I 2636)
PTRC3.Str.dirGeneral 0 0 1 2 3
device annunciation: 1 - ON IEC Status Str.dirGeneral: 0 - UNKNOWN

0 - OFF 1 - FORWARD
2 - BACKWARD
3 - BOTH
PTRC3.Str.phsA
No. Information
2692 67/67-TOC Phase A picked up (67 A picked up) 0 1
PTRC3.Str.phsA 0 1
device annunciation: 1 - ON IEC Status Str.phsA: 0 - FALSE

0 - OFF 1 - TRUE
PTRC3.Str.dirPhsA
No. Information
2692 67/67-TOC Phase A picked up (67 A picked up) 0 1 1 1 1
2628 Phase A forward (Phase A forward) x 0 1 0 1
2632 Phase A reverse (Phase A reverse) x 0 0 1 1
PTRC3.Str.dirPhsA 0 0 1 2 3
device annunciation: 1 - ON IEC Status Str.dirPhsA: 0 - UNKNOWN

0 - OFF 1 - FORWARD
x - irrelevant 2 - BACKWARD

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTRC3.Str.phsB
No. Information
2693 67/67-TOC Phase B picked up (67 B picked up) 0 1
PTRC3.Str.phsB 0 1
device annunciation: 1 - ON IEC Status Str.phsB: 0 - FALSE

0 - OFF 1 - TRUE
PTRC3.Str.dirPhsB
No. Information
2693 67/67-TOC Phase B picked up (67 B picked up) 0 1 1 1 1
2629 Phase B forward (Phase B forward) x 0 1 0 1
2633 Phase B reverse (Phase B reverse) x 0 0 1 1
PTRC3.Str.dirPhsB 0 0 1 2 3
device annunciation: 1 - ON IEC Status Str.dirPhsB: 0 - UNKNOWN

0 - OFF 1 - FORWARD
PTRC3.Str.phsC
No. Information
2694 67/67-TOC Phase C picked up (67 C picked up) 0 1
PTRC3.Str.phsC 0 1
device annunciation: 1 - ON IEC Status Str.phsC: 0 - FALSE

0 - OFF 1 - TRUE
PTRC3.Str.dirPhsC
No. Information
2694 67/67-TOC Phase C picked up (67 C picked up) 0 1 1 1 1
2630 Phase C forward (Phase C forward) x 0 1 0 1
2634 Phase C reverse (Phase C reverse) x 0 0 1 1
PTRC3.Str.dirPhsC 0 0 1 2 3
device annunciation: 1 - ON IEC Status Str.dirPhsC: 0 - UNKNOWN

0 - OFF 1 - FORWARD

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTRC3.Str.neut
No. Information
2695 67N/67N-TOC picked up (67N picked up) 0 1
PTRC3.Str.neut 0 1
device annunciation: 1 - ON IEC Status Str.neut: 0 - FALSE

0 - OFF 1 - TRUE
PTRC3.Str.dirNeut
No. Information
2695 67N/67N-TOC picked up (67N picked up) 0 1 1 1 1
2635 Ground forward (Ground forward) x 0 1 0 1
2636 Ground reverse (Ground reverse) x 0 0 1 1
PTRC3.Str.dirNeut 0 0 1 2 3

0 - OFF 1 - FORWARD
PTRC3.Op
No. Information
2696 67/67N TRIP (67/67N TRIP) 0 1
PTRC3.Op.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.5 Single-Phase Overcurrent Protection (PTOC16, PTOC17)
PTOC16.Mod
No. Information
5963 50 1Ph is ACTIVE (50 1Ph ACTIVE) x x x x x
5962 50 1Ph is BLOCKED (50 1Ph BLOCKED) x x x 1 0
5961 50 1Ph is OFF (50 1Ph OFF) 1 x 0 0 0
50 1Ph-1 PICKUP (P2705) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC16.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC16.Str
No. Information
5974 50 1Ph-1 picked up (50 1Ph-1 PU) 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC16.Op
No. Information
5975 50 1Ph-1 TRIP (50 1Ph-1 TRIP) 0 1

0 - OFF 1 - TRUE
PTOC17.Mod
No. Information
5963 50 1Ph is ACTIVE (50 1Ph ACTIVE) x x x x x
5962 50 1Ph is BLOCKED (50 1Ph BLOCKED) x x x 1 0
5961 50 1Ph is OFF (50 1Ph OFF) 1 x 0 0 0
50 1Ph-2 PICKUP (P2703) = ∞ x 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC17.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC17.Str
No. Information
5977 50 1Ph-2 picked up (50 1Ph-2 PU) 0 1

0 - OFF 1 - TRUE
PTOC17.Op
No. Information
5979 50 1Ph-2 TRIP (50 1Ph-2 TRIP) 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.6 Voltage Protection 27, 59 (PTUVx, PTOVx)
3.6.1 Undervoltage Protection 27 (PTUV1)
PTUV1.Mod
No. Information
6532 27 Undervoltage protection is ACTIVE (27 ACTIVE) x x x x
6531 27 Undervoltage protection is BLOCKED (27 BLOCKED) x x 1 0
170 VT Fuse Failure (alarm instantaneous) (VT FuseFail) x 1 x 0
6530 27 Undervoltage protection switched OFF (27 OFF) 1 0 0 0
PTUV1.Mod.stVal 5 2 2 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
PTUV1.Health
No. Information
PTUV1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUV1.Str
No. Information
6533 27-1 Undervoltage picked up (27-1 picked up) 0 x 1
6534 27-1 Undervoltage PICKUP w/curr. superv (27-1 PU CS) 0 1 x
PTUV1.Str.general 0 1 1

0 - OFF 1 - TRUE
x - irrelevant
PTUV1.Op
No. Information
6539 27-1 Undervoltage TRIP (27-1 TRIP) 0 1
PTUV1.Op.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.6.2 Undervoltage Protection 27 (PTUV2)
PTUV2.Mod
No. Information
6532 27 Undervoltage protection is ACTIVE (27 ACTIVE) x x x x
6531 27 Undervoltage protection is BLOCKED (27 BLOCKED) x x 1 0
170 VT Fuse Failure (alarm instantaneous) (VT FuseFail) x 1 x 0
6530 27 Undervoltage protection switched OFF (27 OFF) 1 0 0 0
PTUV2.Mod.stVal 5 2 2 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
PTUV2.Health
No. Information
PTUV2.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUV2.Str
No. Information
6537 27-2 Undervoltage picked up (27-2 picked up) 0 x 1
6538 27-2 Undervoltage PICKUP w/curr. superv (27-2 PU CS) 0 1 x
PTUV2.Str.general 0 1 1

0 - OFF 1 - TRUE
X - irrelevant
PTUV2.Op
No. Information
6540 27-2 Undervoltage TRIP (27-2 TRIP) 0 1
PTUV2.Op.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.6.3 Overvoltage Protection 59 (PTOV1)
PTOV1.Mod
No. Information
6567 59-Overvoltage protection is ACTIVE (59 ACTIVE) x x x x
6566 59-Overvoltage protection is BLOCKED (59 BLOCKED) x x 1 0
6565 59-Overvoltage protection switched OFF (59 OFF) 1 0 0 0
PTOV1.Mod.stVal 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PTOV1.Health
No. Information
PTOV1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PTOV1.Str
No. Information
6568 59 picked up (59-1 picked up) 0 1
PTOV1.Str.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOV1.Op
No. Information
6570 59 TRIP (59-1 TRIP) 0 1
PTOV1.Op.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.6.4 Overvoltage Protection 59 (PTOV2)
PTOV2.Mod
No. Information
6567 59-Overvoltage protection is ACTIVE (59 ACTIVE) x x x x
6566 59-Overvoltage protection is BLOCKED (59 BLOCKED) x x 1 0
6565 59-Overvoltage protection switched OFF (59 OFF) 1 0 0 0
PTOV2.Mod.stVal 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PTOV2.Health
No. Information
PTOV2.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PTOV2.Str
No. Information
6571 59-2 Overvoltage V>> picked up (59-2 picked up) 0 1
PTOV2.Str.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOV2.Op
No. Information
6573 59-2 Overvoltage V>> TRIP (59-2 TRIP) 0 1
PTOV2.Op.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.7 Negative Sequence Protection 46 (PTOC14, PTOC15, PTOC5)
PTOC14.Mod
No. Information
5153 46 is ACTIVE (46 ACTIVE) x x x x
5152 46 is BLOCKED (46 BLOCKED) x x 1 0
5151 46 switched OFF (46 OFF) 1 0 0 0
PTOC14.Mod.stVal 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PTOC14.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC14.Str
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC14.Op
No. Information
46-1 TRIP (46-1 TRIP) 0 1
device annunciation / setting: 1 - ON / TRUE IEC Status Op.general: 0 - FALSE

0 - OFF / FALSE 1 - TRUE
PTOC15.Mod
No. Information
5151 46 switched OFF (46 OFF) 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC15.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTOC15.Str
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC15.Op
No. Information
46-2 TRIP (46-2 TRIP) 0 1

PTOC5.Mod
No. Information
5151 46 switched OFF (46 OFF) 1 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOC5.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOC5.Str
No. Information
5166 46-TOC picked up (46-TOC pickedup) 0 1

0 - OFF 1 - TRUE
PTOC5.Op
No. Information
46-TOC TRIP (46-TOC TRIP) 0 1


C53000-G1140-C211-4, Edition 03.2010
Mapping
3.8 Motor Protection (PMSS1, PMRI1)
3.8.1 Motor Starting Protection 48 (PMSS1)
PMSS1.Mod
No. Information
6813 Startup supervision is ACTIVE (START-SUP ACT) x x x x
6812 Startup supervision is BLOCKED (START-SUP BLK) x x 1 0
6811 Startup supervision OFF (START-SUP OFF) 1 0 0 0
PMSS1.Mod.stVal 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PMSS1.Health
No. Information
PMSS1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PMSS1.Str
No. Information
6823 Startup supervision Pickup (START-SUP pu) 0 1
PMSS1.Str.general 0 1

0 - OFF 1 - TRUE
PMSS1.Op
No. Information
6821 Startup supervision TRIP (START-SUP TRIP) 0 1
PMSS1.Op.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.8.2 Motor Restart Inhibit 66 (PMRI1)
PMRI1.Mod
No. Information
4826 66 Motor start protection ACTIVE (66 ACTIVE) x x x
4825 66 Motor start protection BLOCKED (66 BLOCKED) x 1 0
4824 66 Motor start protection OFF (66 OFF)) 1 0 0
PMRI1.Mod.stVal 5 2 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
PMRI1.Health
No. Information
PMRI1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PMRI1.Op
No. Information
4827 66 Motor start protection TRIP (66 TRIP) 0 1
PMRI1.Op.general 0 1

0 - OFF 1 - TRUE
PMRI1.StrInhTmm
809 Time untill release of reclose-blocking (T reclose=) PMRI1.StrInhTmm.stVal Absolute value

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.9 Load Jam Protection (PMLJ1)
Function available with Firmware

7SJ61 V4.71 and higher, 7SJ62 V4.71 and higher, 7SJ64 V4.71 and higher,
7SJ80 V4.60 and higher, 7SK80 V4.60 and higher
PMLJ1.Mod
No. Information
10023 Load Jam Protection is ACTIVE (JAM PROT.ACTIVE) x x x 1
10021 Load Jam Protection is BLOCKED (JAM PROT.BLOCK.) x x 1 0
10022 Load Jam Protection is OFF (JAM PROT.OFF) 1 0 0 0
Frequency range is exceeded x 1 0 0
PMLJ1.Mod.stVal 5 5 2 1

4 - TEST/BLOCKED
5 - OFF
PMLJ1.Health
No. Information
PMLJ1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PMLJ1.Str
No. Information
10025 Load Jam Protection picked up (Load Jam pickup) 0 1
PMLJ1.Str.general 0 1

0 - OFF 1 - TRUE
PMLJ1.Op
No. Information
10026 Load Jam Protection TRIP (Load Jam TRIP) 0 1
PMLJ1.Op.general 0 1

0 - OFF 1 - TRUE
PMLJ1.LodJamAlm
No. Information
10024 Load Jam Protection alarm (Load Jam alarm) 0 1
PMLJ1.LodJamAlm.stVal 0 1

0 - OFF 1 - TRUE
PMLJ1.ChgSet
No. Information
PMLJ1.ChgSet.stVal 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.10 Frequency protection 81 O/U (PTUFx, PTOFx)
3.10.1 Frequency protection 81-1 U (PTUF1)
PTUF1.Mod
No. Information
5213 81 ACTIVE (81 ACTIVE) x x x x x x
5212 81 BLOCKED (81 BLOCKED) x x x x 1 0
5206 >BLOCK 81-1 (>BLOCK 81-1) x x x 1 x 0
5214 81 Under Voltage Block (81 Under V Blk) x x 1 x x 0
5211 81 OFF (81 OFF) x 1 0 0 0 0
81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 1 1 1 1
PTUF1.Mod.stVal 5 5 2 2 2 1

4 - TEST/BLOCKED
5 - OFF
PTUF1.Health
No. Information
PTUF1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUF1.Str
No. Information
5232 81-1 picked up (81-1 picked up) 0 0 1 1
81-1 PICKUP (P5403/5404) < Rated Frequency (P214) 0 1 0 1
PTUF1.Str.general 0 0 0 1
device annunciation / setting: 1 - ON / TRUE IEC Status Str.general: 0 - FALSE

PTUF1.Op
No. Information
5236 81-1 TRIP (81-1 TRIP) 0 0 1 1
PTUF1.Op.general 0 0 0 1

PTUF1.BlkV
No. Information
5214 81 Under Voltage Block (81 Under V Blk) 0 0 1 1
PTUF1.BlkV.stVal 0 0 0 1
device annunciation / setting: 1 - ON / TRUE IEC Status BlkV.stVal: 0 - FALSE


C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUF2.Mod
No. Information
5207 >BLOCK 81-2 (>BLOCK 81-2) x x x 1 x 0
5211 81 OFF (81 OFF) x 1 0 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTUF2.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUF2.Str
No. Information

PTUF2.Op
No. Information
5237 81-2 TRIP (81-2 TRIP) 0 0 1 1

PTUF2.BlkV
No. Information


C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUF3.Mod
No. Information
5208 >BLOCK 81-3 (>BLOCK 81-3) x x x 1 x 0
5211 81 OFF (81 OFF) x 1 0 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTUF3.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUF3.Str
No. Information

PTUF3.Op
No. Information
5238 81-3 TRIP (81-3 TRIP) 0 0 1 1

PTUF3.BlkV
No. Information


C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUF4.Mod
No. Information
5209 >BLOCK 81-4 (>BLOCK 81-4) x x x 1 x 0
5211 81 OFF (81 OFF) x 1 0 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTUF4.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTUF4.Str
No. Information

PTUF4.Op
No. Information
5239 81-4 TRIP (81-4 TRIP) 0 0 1 1

PTUF4.BlkV
No. Information


C53000-G1140-C211-4, Edition 03.2010
Mapping
3.10.5 Frequency protection 81-1 O (PTOF1)
PTOF1.Mod
No. Information
5213 81 ACTIVE (81 ACTIVE) x x x x x x x
5212 81 BLOCKED (81 BLOCKED) x x x x x 1 0
5206 >BLOCK 81-1 (>BLOCK 81-1) x x x x 1 x 0
5214 81 Under Voltage Block (81 Under V Blk) x x x 1 x x 0
5211 81 OFF (81 OFF) x x 1 0 0 0 0
81-1 PICKUP (P5403/5404) ≤ Rated Frequency (P214) x 1 x 0 0 0 0
PTOF1.Mod.stVal 5 5 5 2 2 2 1

4 - TEST/BLOCKED
5 - OFF
PTOF1.Health
No. Information
PTOF1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOF1.Str
No. Information
PTOF1.Str.general 0 0 1 0

PTOF1.Op
No. Information
5236 81-1 TRIP (81-1 TRIP) 0 0 1 1
PTOF1.Op.general 0 0 1 0

PTOF1.BlkV
No. Information
PTOF1.BlkV.stVal 0 0 1 0


C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOF2.Mod
No. Information
5211 81 OFF (81 OFF) x x 1 0 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOF2.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOF2.Str
No. Information

PTOF2.Op
No. Information
5237 81-2 TRIP (81-2 TRIP) 0 0 1 1

PTOF2.BlkV
No. Information


C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOF3.Mod
No. Information
5211 81 OFF (81 OFF) x x 1 0 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOF3.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOF3.Str
No. Information

PTOF3.Op
No. Information
5238 81-3 TRIP (81-3 TRIP) 0 0 1 1

PTOF3.BlkV
No. Information


C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOF4.Mod
No. Information
5211 81 OFF (81 OFF) x x 1 0 0 0 0

4 - TEST/BLOCKED
5 - OFF
PTOF4.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTOF4.Str
No. Information

PTOF4.Op
No. Information
5239 81-4 TRIP (81-4 TRIP) 0 0 1 1

PTOF4.BlkV
No. Information


C53000-G1140-C211-4, Edition 03.2010
Mapping
3.11 Thermal overload protection (PTTR1)
PTTR1.Mod
No. Information
1513 49 Overload Protection is ACTIVE (49 O/L ACTIVE) x x x
1512 49 Overload Protection is BLOCKED (49 O/L BLOCK) x 1 0
1511 49 Overload Protection is OFF (49 O / L OFF) 1 0 0
PTTR1.Mod.stVal 5 2 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
PTTR1.Health
No. Information
PTTR1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PTTR1.Str
No. Information
1517 49 Winding Overload (49 Winding O/L) 0 1
PTTR1.Str.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTTR1.Op
No. Information
1521 49 Thermal Overload TRIP (49 Th O/L TRIP) 0 1
PTTR1.Op.general 0 1

0 - OFF 1 - TRUE
PTTR1.AlmThm
No. Information
1516 49 Overload Alarm! Near Thermal Trip (49 O/L Θ Alarm) 0 1
PTTR1.AlmThm.general 0 1
device annunciation: 1 - ON IEC Status AlmThm.general: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.12 Ground Fault Protection 64, 50N(s), 51N(s) (PHIZ1, PSDEx)
3.12.1 Ground Fault Protection 64 (PHIZ1)
PHIZ1.Mod
No. Information
1212 50Ns/67Ns is ACTIVE (50Ns/67Ns ACT) x x x x x x x
1230 Sensitive ground fault detection BLOCKED (Sens. Gnd block) x 1 x x x x 0
170 VT Fuse Failure (alarm instantaneous) (VT FuseFail) x x 1 x x x 0
6509 >Failure: Feeder VT (>FAIL:FEEDER VT) x x x 1 x x 0
6510 >Failure: Busbar VT (>FAIL: BUS VT) x x x x 1 x 0
1211 50Ns/67Ns is OFF (50Ns/67Ns OFF) 1 0 0 0 0 0 0
Frequency range is exceeded x x x x x 1 0
PHIZ1.Mod.stVal 5 2 2 2 2 2 1

4 - TEST/BLOCKED
5 - OFF
PHIZ1.Health
No. Information
PHIZ1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PHIZ1.Str
No. Information
1215 64 displacement voltage pick up (64 Pickup) 0 1
PHIZ1.Str.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PHIZ1.Str.dirGeneral
No. Information
1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x 0 1 0 1 x
1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x 0 0 1 1 x
1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x 0 0 0 0 1
PHIZ1.Str.dirGeneral 0 0 1 2 3 0

0 - OFF 1 - FORWARD
3 - BOTH
PHIZ1.Str.phsA
No. Information
1215 64 displacement voltage pick up (64 Pickup) 0 x 1 1 1 1
1276 Sensitive Gnd fault in forward direction (SensGnd Forward) x x 1 0 1 x
1277 Sensitive Gnd fault in reverse direction (SensGnd Reverse) x x 0 1 1 x
1278 Sensitive Gnd fault direction undefined (SensGnd undef.) x x 0 0 x 1
1272 Sensitive Ground fault picked up in Ph A (Sens. Gnd Ph A) x 0 1 1 1 1
PHIZ1.Str.phsA 0 0 1 1 1 1
device annunciation: 1 - ON IEC Status Str.phsA: 0 -FALSE

0 - OFF 1 - TRUE
PHIZ1.Str.dirPhsA
No. Information
1272 Sensitive Ground fault picked up in Ph A (Sens. Gnd Ph A) x 0 1 1 1 1
PHIZ1.Str.dirPhsA 0 0 1 2 0 0
device annunciation: 1 - ON IEC Status Str.dirPhsA: 0 - UNKNOWN

0 - OFF 1 - FORWARD

C53000-G1140-C211-4, Edition 03.2010
Mapping
PHIZ1.Str.phsB
No. Information
1273 Sensitive Ground fault picked up in Ph B (Sens. Gnd Ph B) x 0 1 1 1 1
PHIZ1.Str.phsB 0 0 1 1 1 1
device annunciation: 1 - ON IEC Status Str.phsB: 0 -FALSE

0 - OFF 1 - TRUE
PHIZ1.Str.dirPhsB
No. Information
1273 Sensitive Ground fault picked up in Ph B (Sens. Gnd Ph B) x 0 1 1 1 1
PHIZ1.Str.dirPhsB 0 0 1 2 0 0
device annunciation: 1 - ON IEC Status Str.dirPhsB: 0 - UNKNOWN

0 - OFF 1 - FORWARD

C53000-G1140-C211-4, Edition 03.2010
Mapping
PHIZ1.Str.phsC
No. Information
1274 Sensitive Ground fault picked up in Ph C (Sens. Gnd Ph C) x 0 1 1 1 1
PHIZ1.Str.phsC 0 0 1 1 1 1
device annunciation: 1 - ON IEC Status Str.phsC: 0 -FALSE

0 - OFF 1 - TRUE
PHIZ1.Str.dirPhsC
No. Information
1274 Sensitive Ground fault picked up in Ph C (Sens. Gnd Ph C) x 0 1 1 1 1
PHIZ1.Str.dirPhsC 0 0 1 2 0 0

0 - OFF 1 - FORWARD
PHIZ1.Op
No. Information
1217 64 displacement voltage element TRIP (64 TRIP) 0 1
PHIZ1.Op.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.12.2 Ground Fault Protection 50N(s) (PSDE1, PSDE2)
PSDE1.Mod
No. Information
1212 50Ns/67Ns is ACTIVE (50Ns/67Ns ACT) x x x x
1230 Sensitive ground fault detection BLOCKED (Sens. Gnd block) x x 1 0
1211 50Ns/67Ns is OFF (50Ns/67Ns OFF) 1 0 0 0
PSDE1.Mod.stVal 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PSDE1.Health
No. Information
PSDE1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PSDE1.Str
No. Information
1224 50Ns-1 Pickup (50Ns-1 Pickup) 0 1
PSDE1.Str.general 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PSDE1.Str.dirGeneral
No. Information
1224 50Ns-1 Pickup (50Ns-1 Pickup) 0 1 1 1 1 1
PSDE1.Str.dirGeneral 0 0 1 2 3 0

0 - OFF 1 - FORWARD
3 - BOTH
PSDE1.Op
No. Information
1226 50Ns-1 TRIP (50Ns-1 TRIP) 0 1
PSDE1.Op.general 0 1

0 - OFF 1 - TRUE
PSDE2.Mod
No. Information
1212 50Ns/67Ns is ACTIVE (50Ns/67Ns ACT) x x x x
1230 Sensitive ground fault detection BLOCKED (Sens. Gnd block) x x 1 0
1211 50Ns/67Ns is OFF (50Ns/67Ns OFF) 1 0 0 0
PSDE2.Mod.stVal 5 2 2 1

4 - TEST/BLOCKED
5 - OFF

C53000-G1140-C211-4, Edition 03.2010
Mapping
PSDE2.Health
No. Information
PSDE2.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
PSDE2.Str
No. Information
1221 50Ns-2 Pickup (50Ns-2 Pickup) 0 1

0 - OFF 1 - TRUE
No. Information
1221 50Ns-2 Pickup (50Ns-2 Pickup) 0 1 1 1 1 1

0 - OFF 1 - FORWARD
3 - BOTH
PSDE2.Op
No. Information
1223 50Ns-2 TRIP (50Ns-2 TRIP) 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.12.3 51 N(s) (PSDE3)
PSDE3.Mod
No. Information
1212 50Ns/67Ns is ACTIVE (50Ns/67Ns ACT) x x x x x
1230 Sensitive ground fault detection BLOCKED (Sens. Gnd block) x x x 1 0
1211 50Ns/67Ns is OFF (50Ns/67Ns OFF) 1 x 0 0 0
M.of PU TD (P3131) = ∞ x 1 0 0 0
PSDE3.Mod.stVal 5 5 2 2 1

4 - TEST/BLOCKED
5 - OFF
PSDE3.Health
No. Information
51 Device is Operational and Protecting (Device OK) x 0 1
16029 sens.grd.flt. 51Ns BLOCKED Setting Error (51Ns BLK PaErr) 1 x 0
PSDE3.Health.stVal 3 3 1

0 - OFF 2 - WARNING
x - irrelevant 3 - ALARM
PSDE3.Str
No. Information
1227 51Ns picked up (51Ns Pickup) 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
No. Information
1227 51Ns picked up (51Ns Pickup) 0 1 1 1 1 1

0 - OFF 1 - FORWARD
3 - BOTH
PSDE3.Op
No. Information
1229 51Ns TRIP (51Ns TRIP) 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.13 Automatic Reclosing System 79 (RREC1)
RREC1.Mod
No. Information
2782 79 Auto recloser is switched ON (79 ON) x x x
2785 79 - Auto-reclose is dynamically BLOCKED (79 DynBlock) x 1 0
2781 79 Auto recloser is switched OFF (79 OFF) 1 0 0
RREC1.Mod.stVal 5 2 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
RREC1.Health
No. Information
RREC1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
RREC1.Op
No. Information
2851 79 - Close command (79 Close) 0 1
RREC1.Op.general 0 1

0 - OFF 1 - TRUE
RREC1.AutoRecSt
No. Information
2801 79 - in progress (79 in progress) 1 1 0 0
2862 79 - cycle successful (79 Successful) 1 0 1 0
RREC1.AutoRecSt.stVal 3 2 3 1
device annunciation: 1 - ON IEC Status AutoRecST.stVal: 1 - ready

0 - OFF 2 - in progress
3 - successful

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.14 Fault Locator (RFLO1)
RFLO1.Mod
No. Information
Fault Locator (P180) = Enabled 1
RFLO1.Mod.stVal 1

3 - TEST
4 - TEST/BLOCKED
5 - OFF
RFLO1.Health
No. Information
RFLO1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
RFLO1.FltZ
Absolute value of the fault RFLO1.FltZ.cVal.mag.f Measured value Absolute value

impedance
RFLO1.FltZ.units.SIUnit 30 Ω (Ohm)
RFLO1.FltZ.units.multiplier 0 1
Angle of the fault impedance RFLO1.FltZ.cVal.ang.f Measured value Angle in °
RFLO1.FltDiskm
1119 Flt Locator: Distance to fault RFLO1.FltDiskm.mag.f Measured value Absolute value
or (dist =)
1122 RFLO1.FltDiskm.units.SIUnit 2 Meter
RFLO1.FltDiskm.units.multiplier 3 Kilo
RFLO1.FltDisPrc
1120 Flt Locator: Distance [%] to fault RFLO1.FltDisPrc.mag.f Measured value Absolute value
(d[%] =)
RFLO1.FltDisPrc.units.SIUnit 1 NONE
RFLO1.FltDisPrc.multiplier 0 1

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.15 Circuit breaker failure protection 50BF(RBRF1)
RBRF1.Mod
No. Information
1452 Breaker failure is BLOCKED (BkrFail BLOCK) x 0 1
1451 Breaker failure is switched OFF (BkrFail OFF) 1 0 0
RBRF1.Mod.stVal 5 1 2

0 - OFF 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF
RBRF1.Health
No. Information
RBRF1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
RBRF1.Str
No. Information
1456 50BF (internal) PICKUP (50BF int Pickup) 0 0 1 1
1457 50BF (external) PICKUP (50BF ext Pickup) 0 1 0 1
RBRF1.Str.general 0 1 1 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RBRF1.OpEx
No. Information
1481 50BF (external) TRIP (50BF ext TRIP) 0 1
RBRF1.OpEx.general 0 1
device annunciation: 1 - ON IEC Status OpEx.general: 0 - FALSE

0 - OFF 1 - TRUE
RBRF1.OpIn
No. Information
1480 50BF (internal) TRIP (50BF int TRIP) 0 1
RBRF1.OpIn.general 0 1
device annunciation: 1 - ON IEC Status OpIn.general: 0 - FALSE

0 - OFF 1 - TRUE
x - irrelevant

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.16 Synchronism and Voltage Check 25 (RSYNx)
RSYN1.Mod
No. Information
170.0051 25-group 1 is BLOCKED (25-1 BLOCK) 0 1 x
170.2101 Sync-group 1 is switched OFF (25-1 OFF) 0 0 1
RSYN1.Mod.stVal 1 2 5

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
RSYN1.Health
No. Information
170.0050 25 Synchronization Error (25 Sync. Error) x x 1 0
51 Device is Operational and Protecting (Device OK) x x 1 1
170.2096 25 Multiple selection of func-groups (25 FG-Error) 1 x 0 0
170.2097 25 Setting error (25 Set-Error) x 1 0 0
RSYN1.Health.stVal 3 3 2 1

0 - OFF 2 - WARNING
RSYN1.Rel
No. Information
170.0049 25 Sync. Release of CLOSE Command (25 CloseRelease) 0 1
RSYN1.Rel.stVal 0 1
device annunciation: 1 - ON IEC Status Rel.stVal: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN1.VInd
No. Information
170.2030 25 Voltage difference (Vdiff) okay (25 Vdiff ok) 0 1
RSYN1.VInd.stVal 1 0
device annunciation: 1 - ON IEC Status VInd.stVal: 0 - FALSE

0 - OFF 1 - TRUE
RSYN1.AngInd
No. Information
170.2032 25 Angle difference (alphadiff) okay (25 αdiff ok) 0 1
RSYN1.AngInd.stVal 1 0
device annunciation: 1 - ON IEC Status AngInd.stVal: 0 - FALSE

0 - OFF 1 - TRUE
RSYN1.HzInd
No. Information
170.2031 25 Frequency difference (fdiff) okay (25 fdiff ok) 0 1
RSYN1.HzInd.stVal 1 0
device annunciation: 1 - ON IEC Status HzInd.stVal: 0 - FALSE

0 - OFF 1 - TRUE
RSYN1.SynPrg
No. Information
170.2022 25-group 1: measurement in progress (25-1 meas.) 0 1
RSYN1.SynPrg.stVal 0 1
device annunciation: 1 - ON IEC Status SynPrg.stVal: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN1.DifVCIc
170.2054 dV = (dV =) RSYN1.DifVClc.mag.f Measured value Absolute value
RSYN1.DifVClc.units.SIUnit 29 V (Volt)
RSYN1.DifVClc.units.multiplier 3 Kilo
RSYN1.DifHzCIc
170.2055 df = (df =) RSYN1. DifHzClc.mag.f Measured value Absolute value
RSYN1. DifHzClc.units.SIUnit 33 Hz
RSYN1. DifHzClc.units.multiplier 0 1
RSYN1.DifAngCIc
170.2056 dalpha = (dα =) RSYN1. DifAngClc.mag.f Measured value Absolute value
RSYN1. DifAngClc.units.SIUnit 9 ° (Degree)
RSYN1. DifAngClc.units.multiplier 0 1

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN2.Mod
No. Information

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
RSYN2.Health
No. Information

0 - OFF 2 - WARNING
RSYN2.Rel
No. Information
RSYN2.Rel.stVal 0 1

0 - OFF 1 - TRUE
RSYN2.VInd
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN2.AngInd
No. Information

0 - OFF 1 - TRUE
RSYN2.HzInd
No. Information

0 - OFF 1 - TRUE
RSYN2.SynPrg
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN2.DifVCIc
RSYN2.DifHzCIc
RSYN2.DifAngCIc

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN3.Mod
No. Information

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
RSYN3.Health
No. Information

0 - OFF 2 - WARNING
RSYN3.Rel
No. Information
RSYN3.Rel.stVal 0 1

0 - OFF 1 - TRUE
RSYN3.VInd
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN3.AngInd
No. Information

0 - OFF 1 - TRUE
RSYN3.HzInd
No. Information

0 - OFF 1 - TRUE
RSYN3.SynPrg
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN3.DifVCIc
RSYN3.DifHzCIc
RSYN3.DifAngCIc

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN4.Mod
No. Information

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
RSYN4.Health
No. Information

0 - OFF 2 - WARNING
RSYN4.Rel
No. Information
RSYN4.Rel.stVal 0 1

0 - OFF 1 - TRUE
RSYN4.VInd
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN4.AngInd
No. Information

0 - OFF 1 - TRUE
RSYN4.HzInd
No. Information

0 - OFF 1 - TRUE
RSYN4.SynPrg
No. Information

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
RSYN4.DifVCIc
RSYN4.DifHzCIc
RSYN4.DifAngCIc

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.17 Three-pole tripping 52 Breaker (XCBR1)
XCBR1.Mod
No. Information
52 At Least 1 Protection Funct. is Active (ProtActive) 1 0
XCBR1.Mod.stVal 1 5

0 - OFF 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF
XCBR1.Health
No. Information
XCBR1.Health.stVal 3 1

0 - OFF 2 - WARNING
XCBR1.Loc
No. Information
XCBR1.Loc.stVal 1 0
device annunciation: 1 - ON IEC Status Loc.stVal: 0 - FALSE

0 - OFF 1 - TRUE
XCBR1.OpCnt
Number of TRIPs= (#of TRIPs=) XCBR1.OpCnt.stVal Metered value Absolute value

C53000-G1140-C211-4, Edition 03.2010
Mapping
XCBR1.Pos
No. Information
4601 >52-a contact (OPEN, if bkr is open) (>52-a) 0 1 0 1
4602 >52-b contact (OPEN, if bkr is closed) (>52-b) 0 0 1 1
XCBR1.Pos.stVal - if spontan information 11 01 10 11
XCBR1.Pos.stVal - if command is running 00 01 10 00
device annunciation: 1 - ON IEC Status Pos.stVal: 00 - INTERMEDIATE STATE

0 - OFF 01 - OFF
10 - ON
11 - BAD STATE
XCBR1.BlkOpn
No. Information
XCBR1.BlkOpn.stVal 0 1
device annunciation: 1 - ON IEC Status BlkOpn.stVal: 0 - FALSE

0 - OFF 1 - TRUE
XCBR1.BlkCls
No. Information
XCBR1.BlkCls.stVal 0 1
device annunciation: 1 - ON IEC Status BlkCls.stVal: 0 - FALSE

0 - OFF 1 - TRUE
XCBR1.CBOpCap
No. Information
XCBR1.CBOpCap.stVal 1
device annunciation: IEC Status CBOpCap.stVal: 1 - NONE

C53000-G1140-C211-4, Edition 03.2010
Mapping
XCBR1.CirSpv
No. Information
6865 74TC Failure Trip Circuit (74TC Trip cir.) 0 1
XCBR1.CirSpv.stVal 0 1
device annunciation: 1 - ON IEC Status CirSpv.stVal: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
XCBR1.SumSwARs1
1021 Accumulation of XCBR1.SumSwARs1.actVal Metered value Current value of

interrupted current Ph A acummulated interrupted
(Σ Ia =) current = actVal × pulsQty
XCBR1.SumSwARs1.units.SIUnit 5 A (Ampere)
XCBR1.SumSwARs1.units.multiplier 3 Kilo
XCBR1.SumSwARs1.pulsQty 1.000000e-002 A / Metered value
XCBR1.SumSwARs2

interrupted current Ph B acummulated interrupted
(Σ Ib =) current = actVal × pulsQty
XCBR1.SumSwARs3

interrupted current Ph C acummulated interrupted
(Σ Ic =) current = actVal × pulsQty

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.18 Tripping Logic of the Entire Device (PTRC1)
PTRC1.Mod
No. Information
52 At Least 1 Protection Funct. is Active (ProtActive) 1 0
PTRC1.Mod.stVal 1 5

0 - OFF 2 - BLOCKED
3 - TEST
4 - TEST/BLOCKED
5 - OFF
PTRC1.Health
No. Information

0 - OFF 2 - WARNING
3 - ALARM
PTRC1.Str
No. Information
501 Relay PICKUP (Relay PICKUP) 0 1

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
PTRC1.Tr
No. Information
511 Relay GENERAL TRIP command (Relay TRIP) 0 1
PTRC1.Tr.general 0 1
device annunciation: 1 - ON IEC Status Tr.general: 0 - FALSE

0 - OFF 1 - TRUE
PTRC1.FinTr
No. Information
2863 79 - Lockout (79 Lockout) 0 1
PTRC1.FinTr.stVal 0 1
device annunciation: 1 - ON IEC Status FinTr.stVal: 0 - FALSE

0 - OFF 1 - TRUE

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.19 Measurement (MMXU1, MSQI1, MMTR1)
3.19.1 Measures (MMXU1)
MMXU1.Mod
No. Information
MMXU1.Mod.stVal 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
MMXU1.Health
No. Information
MMXU1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
MMXU1.TotW
641 P (active power) (P =) MMXU1.TotW.mag.f Measured value Absolute value
MMXU1.TotW.units.SIUnit 62 W (Watt)
MMXU1.TotW.units.multiplier 6 Mega
MMXU1.TotVAr
642 Q (reactive power) (Q =) MMXU1.TotVAr.mag.f Measured value Absolute value
MMXU1.TotVAr.units.SIUnit 63 VAr
MMXU1.TotVAr.units.multiplier 6 Mega
MMXU1.TotVA
645 S (apparent power) (S =) MMXU1.TotVA.mag.f Measured value Absolute value
MMXU1.TotVA.units.SIUnit 61 VA
MMXU1.TotVA.units.multiplier 6 Mega
MMXU1.TotPF
901 Power Factor (PF =) MMXU1.TotPF.mag.f Measured value Absolute value
MMXU1.TotPF.units.SIUnit 1 NONE
MMXU1.TotPF.units.multiplier 0 1

C53000-G1140-C211-4, Edition 03.2010
Mapping
MMXU1.Hz
644 Frequency (Freq=) MMXU1.Hz.mag.f Measured value Absolute value
MMXU1.Hz.units.SIUnit 33 Hz
MMXU1.Hz.units.multiplier 0 1
MMXU1.A
601 Ia (Ia =) MMXU1.A.phsA.cVal.mag.f Measured value Absolute value
MMXU1.A.phsA.units.SIUnit 5 A (Ampere)
MMXU1.A.phsA.units.multiplier 0 1
602 Ib (Ib =) MMXU1.A.phsB.cVal.mag.f Measured value Absolute value
MMXU1.A.phsB.units.SIUnit 5 A (Ampere)
MMXU1.A.phsB.units.multiplier 0 1
603 Ic (Ic =) MMXU1.A.phsC.cVal.mag.f Measured value Absolute value
MMXU1.A.phsC.units.SIUnit 5 A (Ampere)
MMXU1.A.phsC.units.multiplier 0 1
604 In (In =) MMXU1.A.phsC.cVal.mag.f Measured value Absolute value
MMXU1.A.phsC.units.SIUnit 5 A (Ampere)
MMXU1.A.phsC.units.multiplier 0 1

C53000-G1140-C211-4, Edition 03.2010
Mapping
MMXU1.PPV
624 Va-b (Va-b=) MMXU1.PPV.phsAB.cVal.mag.f Measured value Absolute value
MMXU1.PPV.phsAB.units.SIUnit 29 V (Volt)
MMXU1.PPV.phsAB.units.multiplier 3 Kilo
625 Vb-c (Vb-c=) MMXU1.PPV.phsBC.cVal.mag.f Measured value Absolute value
MMXU1.PPV.phsBC.units.SIUnit 29 V (Volt)
MMXU1.PPV.phsBC.units.multiplier 3 Kilo
626 Vc-a (Vc-a=) MMXU1.PPV.phsCA.cVal.mag.f Measured value Absolute value
MMXU1.PPV.phsCA.units.SIUnit 29 V (Volt)
MMXU1.PPV.phsCA.units.multiplier 3 Kilo

C53000-G1140-C211-4, Edition 03.2010
Mapping
MMXU1.PhV
621 Va (Va =) MMXU1.PhV.phsA.cVal.mag.f Measured value Absolute value
MMXU1.PhV.phsA.units.SIUnit 29 V (Volt)
MMXU1.PhV.phsA.units.multiplier 3 Kilo
622 Vb (Vb =) MMXU1.PhV.phsB.cVal.mag.f Measured value Absolute value
MMXU1.PhV.phsB.units.SIUnit 29 V (Volt)
MMXU1.PhV.phsB.units.multiplier 3 Kilo
623 Vc (Vc =) MMXU1.PhV.phsC.cVal.mag.f Measured value Absolute value
MMXU1.PhV.phsC.units.SIUnit 29 V (Volt)
MMXU1.PhV.phsC.units.multiplier 3 Kilo
627 VN (VN =) MMXU1.PhV.neut.cVal.mag.f Measured value Absolute value
MMXU1.PhV.neut.units.SIUnit 29 V (Volt)
MMXU1.PhV.neut.units.multiplier 3 Kilo

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.19.2 Measured values, symmetrical components (MSQI1)
MSQI1.Mod
No. Information
MSQI1.Mod.stVal 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
MSQI1.Health
No. Information
MSQI1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM

C53000-G1140-C211-4, Edition 03.2010
Mapping
MSQI1.SeqA
605 I1 (positive sequence) (I1 =) MSQI1.SeqA.c1.cVal.mag.f Measured value Absolute value
MSQI1.SeqA.c1.units.SIUnit 5 A (Ampere)
MSQI1.SeqA.c1.units.multiplier 0 1
606 I2 (negative sequence) (I2 =) MSQI1.SeqA.c2.cVal.mag.f Measured value Absolute value
831 3Io (zero sequence) (3Io =) MSQI1.SeqA.c3.cVal.mag.f Measured value Absolute value
MSQI1.SeqV
629 V1 (positive sequence) (V1 =) MSQI1.SeqV.c1.cVal.mag.f Measured value Absolute value
MSQI1.SeqV.c1.units.SIUnit 29 V (Volt)
MSQI1.SeqV.c1.units.multiplier 3 Kilo
630 V2 (negative sequence) (V2 =) MSQI1.SeqV.c2.cVal.mag.f Measured value Absolute value
832 Vo (zero sequence) (Vo =) MSQI1.SeqV.c3.cVal.mag.f Measured value Absolute value

C53000-G1140-C211-4, Edition 03.2010
Mapping
3.19.3 Power Metering (MMTR1)
MMTR1.Mod
No. Information
MMTR1.Mod.stVal 1

0 - OFF 2 - BLOCKED
4 - TEST/BLOCKED
5 - OFF
MMTR1.Health
No. Information
MMTR1.Health.stVal 3 1

0 - OFF 2 - WARNING
3 - ALARM
MMTR1.SupWh
924 Wp Forward (Wp+=) MMTR1.SupWh.actVal Metered value Current value of acummulated

interrupted current =
actVal × pulsQty
MMTR1.SupWh.units.SIUnit 72 Wh
MMTR1.SupWh.units.multiplier 6 Mega
MMTR1.SupWh.pulsQty 3.464200e-005 Wh / Metered value

C53000-G1140-C211-4, Edition 03.2010
Mapping
MMTR1.SupVArh
925 Wq Forward (Wq+=) MMTR1.SupVArh.actVal Metered value Current value of acummulated

actVal × pulsQty
MMTR1.SupVArh.units.SIUnit 73 VArh
MMTR1.SupVArh.units.multiplier 6 Mega
MMTR1.SupVArh.pulsQty 3.464200e-005 VArh / Metered value
MMTR1.DmdWh
928 Wp Reverse (Wp-=) MMTR1.DmdWh.actVal Metered value Current value of acummulated

actVal × pulsQty
MMTR1.DmdWh.units.SIUnit 72 Wh
MMTR1.DmdWh.units.multiplier 6 Mega
MMTR1.DmdWh.pulsQty 3.464200e-005 Wh / Metered value
MMTR1.DmdVArh
929 Wq Reverse (Wq-=) MMTR1.DmdVArh.actVal Metered value Current value of acummulated

actVal × pulsQty
MMTR1.DmdVArh.units.SIUnit 73 VArh
MMTR1.DmdVArh.units.multiplier 6 Mega
MMTR1.DmdVArh.pulsQty 3.464200e-005 VArh / Metered value

C53000-G1140-C211-4, Edition 03.2010
Literature
/1/ SIPROTEC 4 Ethernet Module EN 100 IEC 61850 Electrical Interface 100 MBit,
Manual
C54000-G1176-C167
/2/ SIPROTEC 4 System Description
E50417-H1176-C151
/3/ SIPROTEC DIGSI, StartUP
E50417-G1176-C152
/4/ DIGSI CFC, Manual
E50417-H1176-C098
/5/ SIPROTEC SIGRA 4, Manual
E50417-H1176-C1100-C070
/6/ SIPROTEC Multi-Functional Protective Relay with Bay Control 7SJ61, Manual
C53000-G1140-C210
/7/ SIPROTEC Multi-Functional Protective Relay with Local Control 7SJ62/64,
Manual
C53000-G1140-C207
/8/ SIPROTEC Overcurrent Protection 7SJ80, Manual
E50417-G1140-C343
/9/ SIPROTEC Motor Protection 7SK80, Manual
E50417-G1140-C344

C53000-G1140-C211-3, Edition 05.2009
C53000-G1140-C211-3, Edition 05.2009
Index
C Health 164
CALH1 34, 52, 63 Hz 166
ErrBoard1 64 Mod 164
ErrBoard2 64 PhV 168
ErrBoard3 64 PPV 167
ErrBoard4 64 TotPF 165
ErrBoard5 65 TotVA 165
ErrBoard6 65 TotVAr 165
ErrBoard7 65 TotW 165
GrAlm 63 MSQI1 34, 51, 169
GrWrn 63 Health 169
Health 63 Mod 169
Mod 63 SeqA 170
SeqV 170
D
DOI 33 P
PHIZ1 36, 40, 44, 47, 50, 131
F Health 131
Function parameters 34 Mod 131
Functional Scope Op 134
7SJ61 35 Str.dirGeneral 132
7SJ62/63/64 38 Str.dirPhsA 132
7SJ80 43 Str.dirPhsB 133
7SK80 46 Str.dirPhsC 134
Str.general 131
L Str.phsA 132
LD Str.phsB 133
CTRL (Control) 34, 52 Str.phsC 134
DR (Disturbance Recorder) 51 PMLJ1 36, 40, 47, 50, 111
EXT (Extended) 52 ChgSet 112
Logical Device 32 Health 111
MEAS (Measurement) 34, 51 LodJamAlm 112
PROT (Protection) 34, 49 Mod 111
LLN0 32, 34, 49, 51, 52 Op 112
Beh 53, 55, 56 Str 112
Health 53, 55, 57 PMRI1 36, 40, 47, 50, 110
Mod 55, 56 Health 110
OpTmh 54, 56, 57 Mod 110
Logical Node 33, 35, 38, 43, 46, 49 Op 110
LPHD1 32, 34, 50, 51, 52, 62 StrInhTmm 110
DevStr 62 PMSS1 36, 40, 47, 50, 108
PhyHealth 62 Health 108
Proxy 62 Mod 108
Op 109
M Str 109
MMTR1 34, 51, 171 PSDE1 36, 40, 44, 47, 50, 135
DmdVArh 172 Health 135
DmdWh 172 Mod 135
Health 171 Op 136
Mod 171 Str.dirGeneral 136
SupVArh 172 Str.general 135
SupWh 171 PSDE2 36, 40, 44, 47, 50, 136
MMXU1 34, 51, 164 Health 137
A 166, 169 Mod 136

C53000-G1140-C211-4, Edition 03.2010
Index
Op 137 PTOC18 35, 38, 43, 46, 49

Str.dirGeneral 137 Health 72
Str.general 137 Mod 72
PSDE3 40, 44, 47, 50, 138 Op 73
Health 138 Str 72
Mod 138 PTOC2 35, 38, 43, 46, 49, 76
Op 139 ChgSet 77
Str.general 138 Mod 76
PTOC1 35, 38, 43, 46, 49, 70 Op 77
ChgSet 71 Str 77
Health 71 PTOC3 39, 43, 49, 83
Mod 70 ChgSet 84
Op 71 Health 84
Str 71 Mod 83
PTOC10 39, 43, 49, 81 Op 84
ChgSet 82 Str 84
Health 81 PTOC4 39, 44, 46, 49, 87
Mod 81 ChgSet 88
Op 82 Health 88
Str 81 Mod 87
PTOC11 39, 43, 49, 82 Op 88
ChgSet 83 Str 88
Health 82 PTOC5 36, 40, 44, 47, 50, 106
Mod 82 Health 106
Op 83 Mod 106
Str 83 Op 107
PTOC12 39, 44, 46, 49, 85 Str 107
ChgSet 86 PTOC6 35, 38, 43, 46, 49, 68
Health 85 ChgSet 69
Mod 85 Health 68
Op 86 Mod 68
Str 85 Op 69
PTOC13 39, 44, 46, 49, 86 Str 68
ChgSet 87 PTOC7 35, 38, 43, 46, 49, 69
Health 86 ChgSet 70
Mod 86 Health 69
Op 87 Mod 69
Str 87 Op 70
PTOC14 36, 40, 44, 47, 50, 104 Str 70
Health 104 PTOC8 35, 38, 43, 46, 49
Mod 104 ChgSet 75
Op 105 Health 74
Str 104 Mod 74
PTOC15 36, 40, 44, 47, 50, 105 Op 75
Health 105 Str 74
Mod 105 PTOC9 35, 38, 43, 46, 49, 75
Op 106 ChgSet 76
Str 105 Health 75
PTOC16 36, 39, 44, 49, 93 Mod 75
Health 93 Op 76
Mod 93 Str 76
Op 94 PTOF1 41, 45, 48, 50, 121
Str 93 BlkV 122
PTOC17 36, 39, 44, 49, 94 Health 121
Health 94 Mod 121, 123
Mod 94 Op 122
Op 95 Str 122
Str 95 PTOF2 123

C53000-G1140-C211-4, Edition 03.2010
Index
BlkV 124 Str.phsB 91

Health 123 Str.phsC 91
Mod 123 PTTR1 36, 40, 44, 47, 50, 129
Op 124 AlmThm 130
Str 124 Health 129
PTOF3 125 Mod 129
BlkV 126 Str 129
Health 125 Tr 130
Mod 125 PTUF1 41, 45, 48, 50, 113
Op 126 BlkV 114
Str 126 Health 113
PTOF4 127 Mod 113
BlkV 128 Op 114
Health 127 Str 114
Mod 127 PTUF2 115
Op 128 BlkV 116
Str 128 Health 115
PTOV1 41, 45, 48, 49, 100 Mod 115
Health 100 Op 116
Mod 100 Str 116
Op 101 PTUF3 117
Str 100 BlkV 118
PTOV2 41, 45, 48, 102 Health 117
Health 102 Mod 117
Mod 102 Op 118
Op 103 Str 118
Str 102 PTUF4 119
PTRC1 34, 49, 162 BlkV 120
FinTr 163 Health 119
Health 162 Mod 119
Mod 162 Op 120
Str 162 Str 120
Tr 163 PTUV1 41, 45, 48, 49, 96
PTRC2 35, 38, 43, 46, 49, 78 Health 96
Health 78 Mod 96
Mod 74, 78 Op 97
Op 74, 80 Str 97
Str 78 PTUV2 41, 45, 48, 98
Str.dirNeut 80 Mod 98
Str.dirPhsA 79 Op 99
Str.dirPhsB 79 Str 99
Str.dirPhsC 80 PVOC1
Str.neut 80, 92 Mod 74, 80
Str.phsA 79
Str.phsB 79, 80, 91, 92 R
Str.phsC 79, 80, 91, 92 RBRF1 36, 41, 45, 48, 50, 144
PTRC3 39, 43, 49, 89 Health 144
Health 89 Mod 144
Mod 89 OpEx 145
Op 92 OpIn 145
Str 89 Str 144
Str.dirGeneral 90 RDRE1 35, 38, 43, 46, 51, 66
Str.dirNeut 92 FltNum 67
Str.dirPhsA 90 GriFltNum 67
Str.dirPhsB 91 Health 66
Str.dirPhsC 91 Mod 66
Str.neut 92 RcdMade 66, 67
Str.phsA 90 RcdStr 67

C53000-G1140-C211-4, Edition 03.2010
Index
RFLO1 41, 45, 50, 142 BlkOpn 159

FltDiskm 143 CBOpCap 159
FltDisPrc 143 CirSpv 160
FltZ 143 Health 158
Health 142 Loc 158
Mod 142 Mod 158
RREC1 36, 41, 45, 50, 140 OpCnt 158
AutoRecSt 141 Pos 159
Health 140 SumSwARs1 161
Mod 140 SumSwARs2 161
Op 141 SumSwARs3 161
RSYN1 41, 45, 52, 146
AngInd 147
DifAngCIc 148
DifHzCIc 148
DifVCIc 148
Health 146
HzInd 147
Mod 146
Rel 146
SynPrg 147
VInd 147
RSYN2 41, 149
AngInd 150
DifAngCIc 151
DifHzCIc 151
DifVCIc 151
Health 149
HzInd 150
Mod 149
Rel 149
SynPrg 150
VInd 149
RSYN3 41, 152
AngInd 153
DifAngCIc 154
DifHzCIc 154
DifVCIc 154
Health 152
HzInd 153
Mod 152
Rel 152
SynPrg 153
VInd 152
RSYN4 41, 155
AngInd 156
DifAngCIc 157
DifHzCIc 157
DifVCIc 157
Health 155
HzInd 156
Mod 155
Rel 155
SynPrg 156
VInd 155
X
XCBR1 34, 49, 158
BlkCls 159

C53000-G1140-C211-4, Edition 03.2010

Siprotec Multi-Functional Protectiv Relays 7SJ61... 7SJ64 Overcurrent Protection 7SJ80 Motor Protection 7SK80

Uploaded by

Copyright:

Available Formats

Siprotec Multi-Functional Protectiv Relays 7SJ61... 7SJ64 Overcurrent Protection 7SJ80 Motor Protection 7SK80

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Siprotec Multi-Functional Protectiv Relays 7SJ61... 7SJ64 Overcurrent Protection 7SJ80 Motor Protection 7SK80

Uploaded by

Copyright:

Available Formats

Preface, Table of Contents

Siemens Aktiengesellschaft Order No.: C53000-G1140-C211-4

Purpose of this manual

Scope of validity of this Manual

SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT 3

SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT 5

3.1 Device (LPHD1, CALH1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

6 SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT

3.19 Measurement (MMXU1, MSQI1, MMTR1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164

SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT 7

8 SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT

1.2 Association model 11

1.3 Server model 12

1.4 Data set model 13

1.5 Substitution model 14

1.6 Setting group control model 15

1.7 Reporting model 16

1.8 Logging model 19

1.9 Generic substation model 20

1.10 Transmission of sample values model 22

1.11 Control model 23

1.12 Time and time synchronisation model 25

1.13 File transfer model 26

1.14 General items 27

SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT 9

 Data set model

 Setting group control model

 Generic substitution model

 Transmission of sample values model

 File transfer model

10 SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT

1.2 Association model

1.2 Association model

Description Value / Clarification

6 with IEC 61850 Protocol Update

Lost connection detection time range 10 seconds

What called association parameters are Transport selector Y

What is the typical startup time after a 15 SECONDS

SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT 11

1.3 Server model

Description Value / Clarification

Which analogue value (MX) quality bits are Validity:

Which status value (ST) quality bits are Validity:

12 SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT

1.4 Data set model

1.4 Data set model

Description Value / Clarification

SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT 13

1.5 Substitution model

14 SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT

1.6 Setting group control model

1.6 Setting group control model

Description Value / Clarification

SIPROTEC, SIPROTEC 7SJ6/7SJ8/7SK8 , PIXIT 15

1.7 Reporting model

1.7.1 Unbuffered Report

Description Value / Clarification

The supported trigger conditions are Y Integrity

The supported optional fields are Y Sequence-number

Data set model

Setting group control model

Generic substitution model

Transmission of sample values model

File transfer model