0% found this document useful (0 votes)
188 views2 pages

0-30VDC Variable Power Supply Circuit - Circuit Schematic

The document describes a 0-30VDC variable power supply circuit. It works by using a 5.6V zener diode reference voltage that is doubled by an op-amp to create an 11.2V reference voltage. This is then amplified by another op-amp circuit to output a variable 0-30V. The trimmer and resistor allow adjusting the output limits. It can supply 0-3A of adjustable current with less than 0.01% voltage ripple and is controlled by a 24VAC 3A input. Schematic diagrams are commonly used in electronics to describe circuit designs and models.

Uploaded by

Kuntawee
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
188 views2 pages

0-30VDC Variable Power Supply Circuit - Circuit Schematic

The document describes a 0-30VDC variable power supply circuit. It works by using a 5.6V zener diode reference voltage that is doubled by an op-amp to create an 11.2V reference voltage. This is then amplified by another op-amp circuit to output a variable 0-30V. The trimmer and resistor allow adjusting the output limits. It can supply 0-3A of adjustable current with less than 0.01% voltage ripple and is controlled by a 24VAC 3A input. Schematic diagrams are commonly used in electronics to describe circuit designs and models.

Uploaded by

Kuntawee
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

11/23/21, 12:56 PM 0-30VDC variable power supply circuit - Circuit Schematic

0-30VDC variable power supply circuit


Published at 1000 × 405 in 0-30V Stabilized Variable Power Supply with Current Control.

ถูกใจ 0 Tweet Share บันทึก

How the 0-30VDC variable power supply circuit works:

The diode D8 is a 5.6 V zener, which here operates at its zero temperature coefficient current. The voltage in the output of U1 gradually increases till the diode D8 is turned on. When this happens the circuit stabilises and the Zener reference
voltage (5.6 V) appears across the resistor R5. The current which flows through the non inverting input of the op-amp is negligible, therefore the same current flows through R5 and R6, and as the two resistors have the same value the voltage
across the two of them in series will be exactly twice the voltage across each one. Thus the voltage present at the output of the op-amp (pin 6 of U1) is 11.2 V, twice the zeners reference voltage. The integrated circuit U2 has a constant amplifi-
cation factor of approximately 3 X, according to the formula A=(R11+R12)/R11, and raises the 11.2 V reference voltage to approximately 33 V. The trimmer RV1 and the resistor R10 are used for the adjustment of the output voltages limits so
that it can be reduced to 0 V, despite any value tolerances of the other components in the circuit.

Technical Specifications

Input Voltage: ……………. 24 VAC

Input Current: ……………. 3 A (max)

Output Voltage: …………. 0-30 V adjustable

Output Current: …………. 2 mA-3 A adjustable

Output Voltage Ripple: …. 0.01 % maximum

Share this:

     

This schematic diagram come from circuit: 0-30V Stabilized Variable Power Supply with Current Control.

Go to that page to read the explanation about above circuit design.

ร่วมกิจกรรม #iLoveMRDIYBrand
MR.DIY จัดกิจกรรม #iLoveMRDIYBrand แจกรางวัลใหญ่ iPhone 13

Pro และไอเทมมาแรงอีกมากมาย คลิก

MR DIY Thailand เปิด

In the electrical sector, a schematic diagram is usually used to describe the design or model of equipment. Schematic diagrams are usually utilized for the maintenance and repair of electronic and electromechanical
devices / units. Original schematics were made by hand, using standardized templates or pre-printed adhesive symbols, but nowadays Electrical CAD computer software is often used.

In electronic design automation, until the 1980s schematics were virtually the only formal representation for circuits. More lately, using the progress of computer system technology, other representations were in-
troduced and specialized computer languages were developed, because with the explosive development of the complexity of electronic circuits, classic schematics are getting less practical. As an example, hard-
ware description languages are indispensable for contemporary digital circuit design.

Related Posts:

5V
5V Regulated
Regulated Power
Power NiCAD
NiCAD Battery
Battery Charger
Charger
LEDs
LEDs Temperature
Temperature Supply
Supply with
with OverVoltage
OverVoltage with
with Current
Current and
and Voltage
Voltage Aquarium
Aquarium Temperature
Temperature 6A
6A // 0-28V
0-28V Variable
Variable Power
Power
Indicator
Indicator Protection
Protection Limiting
Limiting Find TDK
Hobby technologies
Hobby Power
Power Supply
Supply hereProbe
Probe Supply
Supply

We can provide the most suitable solutions from TDK Group's wide range of
Visit Site
products
TDK Corporation

https://circuitscheme.com/0-30v-stabilized-variable-power-supply-with-current-control.html/0-30vdc-variable-power-supply-circuit 1/2
11/23/21, 12:56 PM 0-30VDC variable power supply circuit - Circuit Schematic

Low Cost PCBA Manufacturing


Fast Prototype PCB Assembly
10 years Electronic contract manufacturer , High Quality Guarantee , Fast Delivery

raypcb.com OPEN

This site uses Akismet to reduce spam. Learn how your comment data is processed.
Iconic One Theme | Powered by Wordpress

Find TDK technologies here


We can provide the most suitable solutions from TDK Group's wide range of
Visit Site
products
TDK Corporation

https://circuitscheme.com/0-30v-stabilized-variable-power-supply-with-current-control.html/0-30vdc-variable-power-supply-circuit 2/2

You might also like