19 Feb 2018 12:55 Conveyor Design Summary Page 1/47

Helix Technologies Pty Ltd

Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Conveyed Material
Material Description COAL BITUMINOUS <50 Surcharge Angle 30 deg
MESH
Low Bulk Density 800 kg/m3 Angle of Repose 45 deg
High Bulk Density 870 kg/m3 Material Lump size 50 mm
Conveyor Data
Conveying Distance 4030.66 m Design Capacity 1000 tonnes/hr
Nett Lift / Lower (-) 7.60 m Belt Speed 5.2 m/s
Belt Details
Pipe Dia/Belt Width 375 1460 mm Calculated Belt % Full 77.4 %
Belt Class & Run Safety Factor ST 1400 5.4 Top Cover Thickness 8 mm
Belt Rated Tension 209 kN/m Bottom Cover Thickness 5 mm
Belt Total Length 8231.4 m Belt Mass 39.62 kg/m
Belt Tensions and Power Calculations Visco
Effective Tens. Fully Loaded 297.71 kN Belt Power - Empty Belt 1501.4 kW
Maximum Tension Tmax 378.51 kN Belt Power - Inclines Loaded 1564.84 kW
Minimum Tension Tmin 81.85 kN Belt Power - Declines Loaded 1487.21 kW
Sag Tension 1.5 % 9.12 kN Belt Power - Fully Loaded 1548.12 kW
Takeup Type Horizontal Gravity Drive Efficiency 95.0 %
Takeup Mass 17000 kg Absorbed Power Fully Loaded 1629.62 kW
Takeup Pulley Belt Tension 83.36 kN Installed Motor Power 2250 kW
Carry and Return Idlers
Carry Idler Trough Angle 360 º Return Idler Trough Angle 360 º
Carry Idler Spacing 1.2 m Return Idler Spacing 1.2 m
Carry Idler No Rolls x Dia 6 x 152 mm Return Idler No Rolls x Dia 6 x 152 mm
Dynamics and Miscellaneous Data
Startup Factor - Fully Loaded 150 % CEMA Temperature Factor Kt 1.00
Startup Factor - Empty 150 % Total Braking Torque LSS 0.00 kNm
Starting Time - Fully Loaded 13.71 sec Stop Time - Loaded, Braking 14.69 sec
Starting Time - Empty 9.92 sec Stop Time - Loaded, Coasting 14.69 sec
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Conveyor Sections - Input Data Page 2/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Station / Sectio
Section Section Cap- Ten Idler Skirt Friction
Length Lift X co- Y co- Z co- acity Adj. Spacing Length No. of Factor
Station Description m m ord m ord m ord m tph kN m m Scrapers Input

1 Tail Tail 5.10 0.08 305.00 4996.00 19.50 0 1.00 0.0000

2 Hopper 5.33 0.00 310.00 4997.00 20.00 1000 1.00 0.0000

3 Int. Pt P1 98.45 3.80 314.99 4998.87 20.00 1000 1.00 0.0000

4 Int. Pt P2 102.22 0.00 383.93 5069.06 23.80 1000 1.00 0.0000

5 Int. Pt P5 263.45 -2.35 441.66 5153.41 23.80 1000 1.00 0.0000

6 Int. Pt P8 577.95 0.05 614.73 5352.02 21.46 1000 1.00 0.0000

7 Int. Pt P12 282.91 0.00 1013.67 5770.20 21.50 1000 1.00 0.0000

8 Int. Pt P13 84.10 4.20 1272.01 5885.52 21.50 1000 1.00 0.0000

9 Int. Pt P15 93.48 0.00 1350.56 5855.78 25.70 1000 1.00 0.0000

10 Int. Pt P17 160.04 -6.20 1440.70 5830.99 25.70 1000 1.00 0.0000

11 Int. Pt P19 355.62 0.00 1598.70 5806.30 19.50 1000 1.00 0.0000

12 Int. Pt P20 505.50 4.50 1838.96 5544.11 19.50 1000 1.00 0.0000

13 Int. Pt P21 380.84 3.83 2078.30 5098.89 24.00 1000 1.00 0.0000

14 Int. Pt P24 641.13 0.00 2440.40 4980.98 27.83 1000 1.00 0.0000

15 Int. Pt P25 415.65 0.00 3081.53 4982.60 27.83 1000 1.00 0.0000

16 Int. Pt P26 64.00 -0.23 3442.27 4776.11 27.83 1000 1.00 0.0000

17 Head Head (P28) 39.12 0.33 3478.86 4723.60 27.10 0 1.00 0.0000

18 Bend HT Bend 15.00 -0.08 3450.00 4750.00 26.50 0 1.00 0.0000

19 Drive Drive 1 25.00 0.00 3465.00 4750.00 25.50 0 1.00 0.0000

20 Int. Pt 44.60 0.08 3440.00 4750.00 25.00 0 1.00 0.0000

21 Drive Drive 2 44.60 0.08 3410.00 4783.00 25.50 0 1.00 0.0000

22 Int. Pt 10.00 0.15 3440.00 4750.00 26.00 0 1.00 0.0000

23 Takeup Takeup 26.03 0.50 3440.00 4760.00 26.50 0 1.00 0.0000

24 Bend Bend 11.06 -0.52 3450.00 4784.00 27.00 0 1.00 0.0000

25 Int. Pt P26 rtn 415.65 0.00 3442.27 4776.11 26.83 0 1.00 0.0000

26 Int. Pt 641.13 0.00 3081.53 4982.60 26.83 0 1.00 0.0000

27 Int. Pt P24 rtn 367.23 -3.83 2440.40 4980.98 26.83 0 1.00 0.0000

28 Int. Pt 519.25 -4.50 2089.54 5089.34 23.00 0 1.00 0.0000

29 Int. Pt P20 rtn 355.62 0.00 1838.96 5544.11 18.50 0 1.00 0.0000

30 Int. Pt 160.04 6.20 1598.70 5806.30 18.50 0 1.00 0.0000

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Conveyor Sections - Input Data Page 3/47
Station / Sectio
Section Section Cap- Ten Idler Skirt Friction
Length Lift X co- Y co- Z co- acity Adj. Spacing Length No. of Factor
Station Description m m ord m ord m ord m tph kN m m Scrapers Input

31 Int. Pt P17 rtn 93.48 0.00 1440.70 5830.99 24.70 0 1.00 0.0000

32 Int. Pt P15 rtn 84.10 -4.20 1350.56 5855.78 24.70 0 1.00 0.0000

33 Int. Pt 282.91 0.00 1272.01 5885.52 20.50 0 1.00 0.0000

34 Int. Pt 577.95 -0.05 1013.67 5770.20 20.50 0 1.00 0.0000

35 Int. Pt P8 rtn 263.45 2.35 614.73 5352.02 20.46 0 1.00 0.0000

36 Int. Pt 102.22 0.00 441.66 5153.41 22.80 0 1.00 0.0000

37 Int. Pt 98.45 -3.80 383.93 5069.06 22.80 0 1.00 0.0000

38 Int. Pt 10.39 0.08 314.99 4998.87 19.00 0 1.00 0.0000

Totals: 8223.05 0.45 0.00 0.00 0

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Takeup & Drive Traction Calculation Page 4/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Drive Torque Start-up Factor Loaded 150 % Takeup Pulley Belt Tension 83.36 kN
Drive Torque Start-up Factor Empty 150 % Takeup Mass 17000 kg
Running Starting Braking

Drive Fully Empty Fully Empty Fully Empty

Number Loaded Belt Loaded Belt Loaded Belt
Drive No. 1 Drive
Pulley No. 19 Lagging Type Ceramic Ceramic Ceramic
Wrap Angle º 180 180 180 180 180 180
Co-efficient of Friction 0.35 0.35 0.45 0.45 0.45 0.45
Drive Factor Cw 0.499 0.499 0.321 0.321 0.321 0.321
Calculated Belt Tension T1 kN 375.23 366.27 658.7 645.21 110.56 120.62
Calculated Belt Tension T2 kN 177.42 174.45 270.76 265.43 93.17 97.42
Minimum Required T2 kN 98.71 95.72 124.53 121.91 5.58 7.45
Surplus T2 Tension (T1-T2) kN 78.71 78.73 146.23 143.52 87.59 89.97
Drive No. 2 Drive
Pulley No. 21 Lagging Type Ceramic Ceramic Ceramic
Wrap Angle º 180 180 180 180 180 180
Co-efficient of Friction 0.35 0.35 0.45 0.45 0.45 0.45
Drive Factor Cw 0.499 0.499 0.321 0.321 0.321 0.321
Calculated Belt Tension T1 kN 179.26 176.29 274.34 269.68 93.38 97.13
Calculated Belt Tension T2 kN 81.85 81.85 80.47 79.95 84.6 85.43
Minimum Required T2 kN 48.61 47.13 62.23 60.9 2.82 3.76
Surplus T2 Tension (T1-T2) kN 33.24 34.72 18.24 19.05 81.78 81.67
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Summary Run / Start Page 5/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Drive Torque Start-up Factor Loaded 150 %

Drive Torque Start-up Factor Empty 150 % Takeup Mass 17000 kg

Running Starting Braking Coasting

Fully Inclines Declines Fully Fully Fully
Loaded Empty Loaded Loaded Loaded Empty Loaded Empty Loaded Empty
Station Tension Tension Tension Tension Tension Tension Tension Tension Tension Tension
No kN kN kN kN kN kN kN kN kN kN
1 Tail 208.34 208.34 208.34 208.34 307.87 345.90 115.42 87.20 115.42 87.20

2 Hopper 209.78 209.78 209.78 209.78 309.81 348.03 116.40 88.04 116.40 88.04

3 Int. Pt 211.38 209.91 211.38 211.36 311.64 348.33 117.77 88.01 117.77 88.01

4 Int. Pt 217.67 213.88 217.67 215.33 322.35 355.66 119.93 89.02 119.93 89.02

5 Int. Pt 220.60 216.47 220.60 217.92 329.87 361.74 118.57 88.54 118.57 88.54

6 Int. Pt 228.34 225.16 229.29 225.61 349.45 379.41 115.26 89.32 115.26 89.32

7 Int. Pt 250.21 246.47 251.05 246.92 397.30 420.45 112.87 93.26 112.87 93.26

8 Int. Pt 261.11 257.19 261.90 257.64 420.92 440.83 111.89 95.47 111.89 95.47

9 Int. Pt 268.25 262.10 269.02 262.55 431.84 448.61 115.50 97.85 115.50 97.85

10 Int. Pt 271.98 265.80 272.72 266.25 439.77 455.49 115.31 98.75 115.31 98.75

11 Int. Pt 272.75 269.77 276.69 266.96 447.74 464.93 109.37 97.91 109.37 97.91

12 Int. Pt 287.08 284.06 290.93 281.25 478.06 491.36 108.77 101.50 108.77 101.50

13 Int. Pt 311.76 306.46 315.53 303.65 525.46 531.01 112.23 108.71 112.23 108.71

14 Int. Pt 328.19 320.25 331.92 317.44 559.01 557.80 112.68 111.05 112.68 111.05

15 Int. Pt 352.00 343.51 355.58 340.70 611.65 602.95 109.58 115.04 109.58 115.04

16 Int. Pt 367.73 358.95 371.19 356.14 646.07 632.58 107.86 117.98 107.86 117.98

17 Head 369.33 360.47 372.71 357.74 650.54 636.28 106.77 117.58 106.77 117.58

18 Bend 372.66 363.75 375.99 361.02 655.36 641.62 108.71 119.05 108.71 119.05

19 Drive 375.23 366.27 378.51 363.54 658.70 645.21 110.56 120.62 110.56 120.62

20 Int. Pt 178.07 175.10 179.14 174.20 272.05 266.96 93.22 97.29 93.22 97.29

21 Drive 179.26 176.29 180.33 175.39 274.34 269.68 93.38 97.13 93.38 97.13

22 Int. Pt 83.04 83.04 83.04 83.04 82.79 82.70 84.73 85.25 84.73 85.25

23 Takeup 83.36 83.36 83.36 83.36 83.36 83.36 83.36 83.36 83.36 83.36

24 Bend 84.81 84.81 84.81 84.81 85.73 86.08 83.95 83.68 83.95 83.68

25 Int. Pt 85.47 85.47 85.47 85.47 86.92 87.48 84.12 83.71 84.12 83.71

26 Int. Pt 96.40 96.40 96.40 96.40 108.12 112.60 85.46 82.14 85.46 82.14

27 Int. Pt 114.83 114.83 114.83 114.83 142.38 152.91 89.11 81.30 89.11 81.30

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Summary Run / Start Page 6/47

Running Starting Braking Coasting

Fully Inclines Declines Fully Fully Fully
Loaded Empty Loaded Loaded Loaded Empty Loaded Empty Loaded Empty
Station Tension Tension Tension Tension Tension Tension Tension Tension Tension Tension
No kN kN kN kN kN kN kN kN kN kN
28 Int. Pt 124.08 124.08 124.08 124.08 160.70 174.70 89.90 79.51 89.90 79.51

29 Int. Pt 137.20 137.20 137.20 137.20 186.64 205.54 91.04 77.03 91.04 77.03

30 Int. Pt 148.88 148.88 148.88 148.88 207.11 229.36 94.52 78.01 94.52 78.01

31 Int. Pt 156.67 156.67 156.67 156.67 218.85 242.61 98.62 80.99 98.62 80.99

32 Int. Pt 159.88 159.88 159.88 159.88 224.37 249.01 99.68 81.40 99.68 81.40

33 Int. Pt 161.17 161.17 161.17 161.17 227.73 253.17 99.03 80.16 99.03 80.16

34 Int. Pt 171.04 171.04 171.04 171.04 244.59 272.70 102.38 81.52 102.38 81.52

35 Int. Pt 191.42 191.42 191.42 191.42 279.25 312.81 109.43 84.53 109.43 84.53

36 Int. Pt 201.92 201.92 201.92 201.92 296.25 332.29 113.86 87.11 113.86 87.11

37 Int. Pt 205.76 205.76 205.76 205.76 302.61 339.62 115.34 87.88 115.34 87.88

38 Int. Pt 208.04 208.04 208.04 208.04 307.32 345.25 115.36 87.21 115.36 87.21

Minimum Ten 83.04 83.04 83.04 83.04 82.79 82.70 83.36 77.03 83.36 77.03
Maximum Ten 375.23 366.27 378.51 363.54 658.70 645.21 119.93 120.62 119.93 120.62
Effective Ten 297.71 288.73 300.93 286.00

Ave. Belt Ten 216.29 213.59 217.56 212.85 336.84 351.46 103.77 92.21 103.77 92.21
Belt Elong. m 7.519 7.368 7.59 7.326 14.261 15.079 1.225 0.579 1.225 0.579
T/up Travel m 3.76 3.684 3.795 3.663 7.13 7.54 0.612 0.29 0.612 0.29
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
 19 Feb 2018 12:55 Belt Details Report Page 7/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Low BD = 800kg/m3 High BD = 870kg/m3

Conveyed Material Belt Speed & Capacity
Material Description COAL BITUMINOUS <50 Belt Speed 5.2 m/s
MESH
Low Bulk Density 800 kg/m3 Belt Design Capacity Input 1000 tonnes/hr
High Bulk Density 870 kg/m3 Section Loading Max Capacity 1000 tonnes/hr
Surcharge Angle 30 deg Carry Idler Trough Angle 360 º
Angle of Repose 45 deg Belt Dimensions
Material Lump size 50 mm Top Cover Thickness 8 mm
Belt Make & Class Bottom Cover Thickness 5 mm
Belt Category Goodyear Steel Belt Carcass Thickness 5.7 mm
Belt Description GOODYEAR FLEXSTEEL Belt Total Thickness 18.7 mm
STACKER
Belt Class / Plies ST 1400 0 Belt Total Belt Length (L) 8231.4 m
Belt Reinforcement Fibre Steel Time for 1 Revolution 1583.0 sec
Pipe Dia/Belt Width 375 1460 mm Belt Load Area and Capacity at 800kg/m3
Belt Modulus 100800 kN/m Minimum Rec. Edge Distance 0 mm
Cord Diameter 5.9 mm Belt Overlap Length Low BD 170 mm
Cord Pitch 15.9 mm Load Burden Depth 249 mm
Number of Cords 0 Load Burden Width 330 mm
Belt Tensions Belt Load Area at 100% Full
and Low Bulk Density 0.0863 m2
Belt Rated Tension / m width 209 kN/m
Calculated Tension / m width 259.3 kN/m Belt Load Area Utilised at Low
Belt Rated Tension for width 305.1 kN Bulk Density 0.0668 m2
Calculated Max Run Tension 378.51 kN Belt Actual % Full at Low BD 77.4 %
Minimum Tension Tmin 81.85 kN Belt Load Area and Capacity at 870kg/m3
Allowable Tension Rise, Starting 150 % Minimum Rec. Edge Distance 0 mm
Allowable Belt Tension, Starting 457.7 kN Belt Overlap Length High BD 170 mm
Actual Belt Tension, Starting 658.7 kN Belt Load Area Utilised at High
Bulk Density 0.0614 m2
Belt Tensions exceed Allowable Tensions
Belt and Material Mass Belt Actual % Full at High BD 71.1 %
Belt Top Cover Mass 13.2 kg/m Flooded Belt Capacity at 870kg/m3
Belt Bottom Cover Mass 8.2 kg/m Flooded Belt Load Area at
100% Full (High BD) 0.0863 m2
Belt Carcass Mass 18.2 kg/m
Belt Mass Wb (per linear m) 39.6 kg/m Flooded Belt Capacity 1406 tonnes/hr
Material Mass Wm 53.4 kg/m Flooded Belt Material Mass 75.1 kg/m
Total Mass (Wb + Wm) 93 kg/m
Total Belt Mass (Wb x L) 326126 kg
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m -22 this is tooPipe
small in some cases
Coale.g the 440m radius at P25 and will
C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo Existing Conveyor PC01 1000tph Helix
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
4km.xml
Conveyor
Ver 6.0.20.3 under Calcs menu in Helix delta-T6. Licenced to Helix Technologies Technologies
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
19 Feb 2018 12:55 Belt
this is larger than 70% recommended. This may result Details
in material Report
spillage
Page 8/47
and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Summary Belt Sag Page 9/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Allowable Belt Sag % Running 1.5 %

Allowable Belt Sag % Start / Stop 5 % Takeup Mass 17000 kg

Running Starting Braking Coasting

Fully Inclines Declines Fully Fully Fully
Loaded Empty Loaded Loaded Loaded Empty Loaded Empty Loaded Empty
Station Tension Tension Tension Tension Tension Tension Tension Tension Tension Tension
No kN kN kN kN kN kN kN kN kN kN
1 Tail 208.34 208.34 208.34 208.34 307.87 345.90 115.42 87.20 115.42 87.20
Idler Spacing m 1.00
Belt Sag % 0.02 0.02 0.02 0.02 0.02 0.01 0.04 0.06 0.04 0.06
2 Hopper 209.78 209.78 209.78 209.78 309.81 348.03 116.40 88.04 116.40 88.04
Idler Spacing m 1.00
Belt Sag % 0.05 0.02 0.05 0.05 0.04 0.01 0.1 0.06 0.1 0.06
3 Int. Pt 211.38 209.91 211.38 211.36 311.64 348.33 117.77 88.01 117.77 88.01
Idler Spacing m 1.00
Belt Sag % 0.05 0.02 0.05 0.02 0.04 0.01 0.1 0.06 0.1 0.06
4 Int. Pt 217.67 213.88 217.67 215.33 322.35 355.66 119.93 89.02 119.93 89.02
Idler Spacing m 1.00
Belt Sag % 0.05 0.02 0.05 0.05 0.04 0.01 0.1 0.05 0.1 0.05
5 Int. Pt 220.60 216.47 220.60 217.92 329.87 361.74 118.57 88.54 118.57 88.54
Idler Spacing m 1.00
Belt Sag % 0.05 0.02 0.02 0.05 0.03 0.01 0.1 0.05 0.1 0.05
6 Int. Pt 228.34 225.16 229.29 225.61 349.45 379.41 115.26 89.32 115.26 89.32
Idler Spacing m 1.00
Belt Sag % 0.05 0.02 0.05 0.02 0.03 0.01 0.1 0.05 0.1 0.05
7 Int. Pt 250.21 246.47 251.05 246.92 397.30 420.45 112.87 93.26 112.87 93.26
Idler Spacing m 1.00
Belt Sag % 0.05 0.02 0.05 0.05 0.03 0.01 0.1 0.05 0.1 0.05
8 Int. Pt 261.11 257.19 261.90 257.64 420.92 440.83 111.89 95.47 111.89 95.47
Idler Spacing m 1.00
Belt Sag % 0.04 0.02 0.04 0.02 0.03 0.01 0.1 0.05 0.1 0.05
9 Int. Pt 268.25 262.10 269.02 262.55 431.84 448.61 115.50 97.85 115.50 97.85
Idler Spacing m 1.00
Belt Sag % 0.04 0.02 0.04 0.04 0.03 0.01 0.1 0.05 0.1 0.05
10 Int. Pt 271.98 265.80 272.72 266.25 439.77 455.49 115.31 98.75 115.31 98.75
Idler Spacing m 1.00
Belt Sag % 0.04 0.02 0.02 0.04 0.03 0.01 0.1 0.05 0.1 0.05
11 Int. Pt 272.75 269.77 276.69 266.96 447.74 464.93 109.37 97.91 109.37 97.91
Idler Spacing m 1.00
Belt Sag % 0.04 0.02 0.04 0.04 0.03 0.01 0.1 0.05 0.1 0.05

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Summary Belt Sag Page 10/47

Running Starting Braking Coasting

Fully Inclines Declines Fully Fully Fully
Loaded Empty Loaded Loaded Loaded Empty Loaded Empty Loaded Empty
Station Tension Tension Tension Tension Tension Tension Tension Tension Tension Tension
No kN kN kN kN kN kN kN kN kN kN
12 Int. Pt 287.08 284.06 290.93 281.25 478.06 491.36 108.77 101.50 108.77 101.50
Idler Spacing m 1.00
Belt Sag % 0.04 0.02 0.04 0.02 0.02 0.01 0.1 0.05 0.1 0.05
13 Int. Pt 311.76 306.46 315.53 303.65 525.46 531.01 112.23 108.71 112.23 108.71
Idler Spacing m 1.00
Belt Sag % 0.04 0.02 0.04 0.02 0.02 0.01 0.1 0.04 0.1 0.04
14 Int. Pt 328.19 320.25 331.92 317.44 559.01 557.80 112.68 111.05 112.68 111.05
Idler Spacing m 1.00
Belt Sag % 0.03 0.02 0.03 0.04 0.02 0.01 0.1 0.04 0.1 0.04
15 Int. Pt 352.00 343.51 355.58 340.70 611.65 602.95 109.58 115.04 109.58 115.04
Idler Spacing m 1.00
Belt Sag % 0.03 0.01 0.03 0.03 0.02 0.01 0.1 0.04 0.1 0.04
16 Int. Pt 367.73 358.95 371.19 356.14 646.07 632.58 107.86 117.98 107.86 117.98
Idler Spacing m 1.00
Belt Sag % 0.03 0.01 0.01 0.03 0.02 0.01 0.11 0.04 0.11 0.04
17 Head 369.33 360.47 372.71 357.74 650.54 636.28 106.77 117.58 106.77 117.58
Idler Spacing m 1.00
Belt Sag % 0.01 0.01 0.01 0.01 0.01 0.01 0.05 0.04 0.05 0.04
18 Bend 372.66 363.75 375.99 361.02 655.36 641.62 108.71 119.05 108.71 119.05
Idler Spacing m 1.00
Belt Sag % 0.01 0.01 0.01 0.01 0.01 0.01 0.04 0.04 0.04 0.04
19 Drive 375.23 366.27 378.51 363.54 658.70 645.21 110.56 120.62 110.56 120.62
Idler Spacing m 1.00
Belt Sag % 0.01 0.01 0.01 0.01 0.01 0.01 0.04 0.04 0.04 0.04
20 Int. Pt 178.07 175.10 179.14 174.20 272.05 266.96 93.22 97.29 93.22 97.29
Idler Spacing m 1.00
Belt Sag % 0.03 0.03 0.03 0.03 0.02 0.02 0.05 0.05 0.05 0.05
21 Drive 179.26 176.29 180.33 175.39 274.34 269.68 93.38 97.13 93.38 97.13
Idler Spacing m 1.00
Belt Sag % 0.03 0.03 0.03 0.03 0.02 0.02 0.05 0.05 0.05 0.05
22 Int. Pt 83.04 83.04 83.04 83.04 82.79 82.70 84.73 85.25 84.73 85.25
Idler Spacing m 1.00
Belt Sag % 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06
23 Takeup 83.36 83.36 83.36 83.36 83.36 83.36 83.36 83.36 83.36 83.36
Idler Spacing m 1.00
Belt Sag % 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06
24 Bend 84.81 84.81 84.81 84.81 85.73 86.08 83.95 83.68 83.95 83.68
Idler Spacing m 1.00
Belt Sag % 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06
25 Int. Pt 85.47 85.47 85.47 85.47 86.92 87.48 84.12 83.71 84.12 83.71
Idler Spacing m 1.00
Belt Sag % 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06 0.06
26 Int. Pt 96.40 96.40 96.40 96.40 108.12 112.60 85.46 82.14 85.46 82.14
Idler Spacing m 1.00
Belt Sag % 0.05 0.05 0.05 0.05 0.04 0.04 0.06 0.06 0.06 0.06
27 Int. Pt 114.83 114.83 114.83 114.83 142.38 152.91 89.11 81.30 89.11 81.30
Idler Spacing m 1.00
Belt Sag % 0.04 0.04 0.04 0.04 0.03 0.03 0.05 0.06 0.05 0.06

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Summary Belt Sag Page 11/47

Running Starting Braking Coasting

Fully Inclines Declines Fully Fully Fully
Loaded Empty Loaded Loaded Loaded Empty Loaded Empty Loaded Empty
Station Tension Tension Tension Tension Tension Tension Tension Tension Tension Tension
No kN kN kN kN kN kN kN kN kN kN
28 Int. Pt 124.08 124.08 124.08 124.08 160.70 174.70 89.90 79.51 89.90 79.51
Idler Spacing m 1.00
Belt Sag % 0.04 0.04 0.04 0.04 0.03 0.03 0.05 0.06 0.05 0.06
29 Int. Pt 137.20 137.20 137.20 137.20 186.64 205.54 91.04 77.03 91.04 77.03
Idler Spacing m 1.00
Belt Sag % 0.04 0.04 0.04 0.04 0.03 0.02 0.05 0.06 0.05 0.06
30 Int. Pt 148.88 148.88 148.88 148.88 207.11 229.36 94.52 78.01 94.52 78.01
Idler Spacing m 1.00
Belt Sag % 0.03 0.03 0.03 0.03 0.02 0.02 0.05 0.06 0.05 0.06
31 Int. Pt 156.67 156.67 156.67 156.67 218.85 242.61 98.62 80.99 98.62 80.99
Idler Spacing m 1.00
Belt Sag % 0.03 0.03 0.03 0.03 0.02 0.02 0.05 0.06 0.05 0.06
32 Int. Pt 159.88 159.88 159.88 159.88 224.37 249.01 99.68 81.40 99.68 81.40
Idler Spacing m 1.00
Belt Sag % 0.03 0.03 0.03 0.03 0.02 0.02 0.05 0.06 0.05 0.06
33 Int. Pt 161.17 161.17 161.17 161.17 227.73 253.17 99.03 80.16 99.03 80.16
Idler Spacing m 1.00
Belt Sag % 0.03 0.03 0.03 0.03 0.02 0.02 0.05 0.06 0.05 0.06
34 Int. Pt 171.04 171.04 171.04 171.04 244.59 272.70 102.38 81.52 102.38 81.52
Idler Spacing m 1.00
Belt Sag % 0.03 0.03 0.03 0.03 0.02 0.02 0.05 0.06 0.05 0.06
35 Int. Pt 191.42 191.42 191.42 191.42 279.25 312.81 109.43 84.53 109.43 84.53
Idler Spacing m 1.00
Belt Sag % 0.03 0.03 0.03 0.03 0.02 0.02 0.04 0.06 0.04 0.06
36 Int. Pt 201.92 201.92 201.92 201.92 296.25 332.29 113.86 87.11 113.86 87.11
Idler Spacing m 1.00
Belt Sag % 0.02 0.02 0.02 0.02 0.02 0.01 0.04 0.06 0.04 0.06
37 Int. Pt 205.76 205.76 205.76 205.76 302.61 339.62 115.34 87.88 115.34 87.88
Idler Spacing m 1.00
Belt Sag % 0.02 0.02 0.02 0.02 0.02 0.01 0.04 0.06 0.04 0.06
38 Int. Pt 208.04 208.04 208.04 208.04 307.32 345.25 115.36 87.21 115.36 87.21
Idler Spacing m 1.00
Belt Sag % 0.02 0.02 0.02 0.02 0.02 0.01 0.04 0.06 0.04 0.06

Minimum Ten 83.04 83.04 83.04 83.04 82.79 82.70 83.36 77.03 83.36 77.03
Maximum Sag 0.06 0.06 0.06 0.06 0.06 0.06 0.11 0.06 0.11 0.06
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Run Fully Loaded Page 12/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Takeup Mass 17000 kg

Tensions Visco
Section Section Ten Material Skirt Scraper Section
Station / Pulley
Length Lift T1 Run T2 Run Tp Drive Adj. Accel. Friction Friction Effective Friction
Station m m kN kN Pulley Te kN kN kN kN kN Tension Factor

1 Tail 5.10 0.08 208.34 209.62 1.28 0.16 0.0396

2 Hopper 5.33 0.00 209.78 209.78 1.44 0.15 0.0247

3 Int. Pt 98.45 3.80 211.38 211.38 6.29 0.0247

4 Int. Pt 102.22 0.00 217.67 217.67 2.93 0.0247

5 Int. Pt 263.45 -2.35 220.60 220.60 7.74 0.0323

6 Int. Pt 577.95 0.05 228.34 228.34 21.87 0.0325

7 Int. Pt 282.91 0.00 250.21 250.21 10.90 0.0331

8 Int. Pt 84.10 4.20 261.11 261.11 7.14 0.0339

9 Int. Pt 93.48 0.00 268.25 268.25 3.73 0.0343

10 Int. Pt 160.04 -6.20 271.98 271.98 0.77 0.0346

11 Int. Pt 355.62 0.00 272.75 272.75 14.33 0.0347

12 Int. Pt 505.50 4.50 287.08 287.08 24.68 0.035

13 Int. Pt 380.84 3.83 311.76 311.76 16.43 0.0292

14 Int. Pt 641.13 0.00 328.19 328.19 23.81 0.0319

15 Int. Pt 415.65 0.00 352.00 352.00 15.73 0.0326

16 Int. Pt 64.00 -0.23 367.73 367.73 1.60 0.0243

17 Head 39.12 0.33 369.33 371.52 2.19 1.14 0.0406

18 Bend 15.00 -0.08 372.66 374.87 2.21 0.36 0.0406

19 Drive 25.00 0.00 375.23 177.42 1.66 197.81 0.65 0.0406

20 Int. Pt 44.60 0.08 178.07 178.07 1.19 0.0408

21 Drive 44.60 0.08 179.26 81.85 0.83 97.41 1.19 0.0408

22 Int. Pt 10.00 0.15 83.04 83.04 0.32 0.0412

23 Takeup 26.03 0.50 83.36 83.93 0.57 0.88 0.0412

24 Bend 11.06 -0.52 84.81 85.38 0.58 0.09 0.0412

25 Int. Pt 415.65 0.00 85.47 85.47 10.93 0.0412

26 Int. Pt 641.13 0.00 96.40 96.40 18.43 0.045

27 Int. Pt 367.23 -3.83 114.83 114.83 9.25 0.0458

28 Int. Pt 519.25 -4.50 124.08 124.08 13.12 0.0448

29 Int. Pt 355.62 0.00 137.20 137.20 11.68 0.0514

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Run Fully Loaded Page 13/47
Tensions Visco
Section Section Ten Material Skirt Scraper Section
Station / Pulley
Length Lift T1 Run T2 Run Tp Drive Adj. Accel. Friction Friction Effective Friction
Station m m kN kN Pulley Te kN kN kN kN kN Tension Factor

30 Int. Pt 160.04 6.20 148.88 148.88 7.79 0.0527

31 Int. Pt 93.48 0.00 156.67 156.67 3.21 0.0538

32 Int. Pt 84.10 -4.20 159.88 159.88 1.29 0.0544

33 Int. Pt 282.91 0.00 161.17 161.17 9.87 0.0546

34 Int. Pt 577.95 -0.05 171.04 171.04 20.38 0.0553

35 Int. Pt 263.45 2.35 191.42 191.42 10.50 0.057

36 Int. Pt 102.22 0.00 201.92 201.92 3.84 0.0589

37 Int. Pt 98.45 -3.80 205.76 205.76 2.28 0.0597

38 Int. Pt 10.39 0.08 208.04 208.04 0.30 0.0407

Totals: 9.32 295.2 0.00 1.44 0.00 0.00 286.95

Maximum Tension 375.23 kN Total Effective Tension 297.71 kN
Minimum Tension 81.85 kN Total Belt Power (Te x V) 1548.12 kW
Average Tension Fully Loaded 216.29 kN Belt Modulus 100800 kN/m
Average Tension Belt Stationary 81.86 kN Total Belt Length 8231.36 m
Average Tension Difference 134.43 kN Belt Elastic Elongation 7.519 m
Takeup Movement 3.76 m
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Run Empty Page 14/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Station / Pulley Tensions Visco

Section Section Ten Material Skirt Scraper Section
Length Lift T1 Run T2 Run Tp Drive Adj. Accel. Friction Friction Effective Friction
Station m m kN kN Pulley Te kN kN kN kN kN Tension Factor

1 Tail 5.10 0.08 208.34 209.62 1.28 0.16 0.0396

2 Hopper 5.33 0.00 209.78 209.78 0.13 0.0247

3 Int. Pt 98.45 3.80 209.91 209.91 3.97 0.0247

4 Int. Pt 102.22 0.00 213.88 213.88 2.59 0.0247

5 Int. Pt 263.45 -2.35 216.47 216.47 8.69 0.0323

6 Int. Pt 577.95 0.05 225.16 225.16 21.31 0.0325

7 Int. Pt 282.91 0.00 246.47 246.47 10.72 0.0331

8 Int. Pt 84.10 4.20 257.19 257.19 4.91 0.0339

9 Int. Pt 93.48 0.00 262.10 262.10 3.70 0.0343

10 Int. Pt 160.04 -6.20 265.80 265.80 3.97 0.0346

11 Int. Pt 355.62 0.00 269.77 269.77 14.29 0.0347

12 Int. Pt 505.50 4.50 284.06 284.06 22.40 0.035

13 Int. Pt 380.84 3.83 306.46 306.46 13.79 0.0292

14 Int. Pt 641.13 0.00 320.25 320.25 23.26 0.0319

15 Int. Pt 415.65 0.00 343.51 343.51 15.44 0.0326

16 Int. Pt 64.00 -0.23 358.95 358.95 1.52 0.0243

17 Head 39.12 0.33 360.47 362.61 2.14 1.14 0.0406

18 Bend 15.00 -0.08 363.75 365.91 2.16 0.36 0.0406

19 Drive 25.00 0.00 366.27 174.45 1.63 191.82 0.65 0.0406

20 Int. Pt 44.60 0.08 175.10 175.10 1.19 0.0408

21 Drive 44.60 0.08 176.29 81.85 0.84 94.44 1.19 0.0408

22 Int. Pt 10.00 0.15 83.04 83.04 0.32 0.0412

23 Takeup 26.03 0.50 83.36 83.93 0.57 0.88 0.0412

24 Bend 11.06 -0.52 84.81 85.38 0.58 0.09 0.0412

25 Int. Pt 415.65 0.00 85.47 85.47 10.93 0.0412

26 Int. Pt 641.13 0.00 96.40 96.40 18.43 0.045

27 Int. Pt 367.23 -3.83 114.83 114.83 9.25 0.0458

28 Int. Pt 519.25 -4.50 124.08 124.08 13.12 0.0448

29 Int. Pt 355.62 0.00 137.20 137.20 11.68 0.0514

30 Int. Pt 160.04 6.20 148.88 148.88 7.79 0.0527

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Run Empty Page 15/47
Station / Pulley Tensions Visco
Section Section Ten Material Skirt Scraper Section
Length Lift T1 Run T2 Run Tp Drive Adj. Accel. Friction Friction Effective Friction
Station m m kN kN Pulley Te kN kN kN kN kN Tension Factor

31 Int. Pt 93.48 0.00 156.67 156.67 3.21 0.0538

32 Int. Pt 84.10 -4.20 159.88 159.88 1.29 0.0544

33 Int. Pt 282.91 0.00 161.17 161.17 9.87 0.0546

34 Int. Pt 577.95 -0.05 171.04 171.04 20.38 0.0553

35 Int. Pt 263.45 2.35 191.42 191.42 10.50 0.057

36 Int. Pt 102.22 0.00 201.92 201.92 3.84 0.0589

37 Int. Pt 98.45 -3.80 205.76 205.76 2.28 0.0597

38 Int. Pt 10.39 0.08 208.04 208.04 0.30 0.0407

Totals: 9.19 286.27 0.00 0.00 279.54

Maximum Tension 366.27 kN Total Effective Tension 288.73 kN
Minimum Tension 81.85 kN Total Belt Power (Te x V) 1501.4 kW
Average Tension Fully Loaded 213.59 kN Belt Modulus 100800 kN/m
Average Tension Belt Stationary 81.86 kN Total Belt Length 8231.36 m
Average Tension Difference 131.73 kN Belt Elastic Elongation 7.368 m
Takeup Movement 3.684 m

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Run Inclines Loaded Page 16/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Station / Pulley Tensions Visco

Section Section Ten Material Skirt Scraper Section
Length Lift T1 Run T2 Run Tp Drive Adj. Accel. Friction Friction Effective Friction
Station m m kN kN Pulley Te kN kN kN kN kN Tension Factor

1 Tail 5.10 0.08 208.34 209.62 1.28 0.16 0.0396

2 Hopper 5.33 0.00 209.78 209.78 1.44 0.15 0.0247

3 Int. Pt 98.45 3.80 211.38 211.38 6.29 0.0247

4 Int. Pt 102.22 0.00 217.67 217.67 2.93 0.0247

5 Int. Pt 263.45 -2.35 220.60 220.60 8.69 0.0571

6 Int. Pt 577.95 0.05 229.29 229.29 21.76 0.0323

7 Int. Pt 282.91 0.00 251.05 251.05 10.85 0.033

8 Int. Pt 84.10 4.20 261.90 261.90 7.12 0.0337

9 Int. Pt 93.48 0.00 269.02 269.02 3.70 0.0341

10 Int. Pt 160.04 -6.20 272.72 272.72 3.97 0.0625

11 Int. Pt 355.62 0.00 276.69 276.69 14.24 0.0344

12 Int. Pt 505.50 4.50 290.93 290.93 24.60 0.0349

13 Int. Pt 380.84 3.83 315.53 315.53 16.39 0.0291

14 Int. Pt 641.13 0.00 331.92 331.92 23.66 0.0318

15 Int. Pt 415.65 0.00 355.58 355.58 15.61 0.0323

16 Int. Pt 64.00 -0.23 371.19 371.19 1.52 0.0395

17 Head 39.12 0.33 372.71 374.85 2.14 1.14 0.0406

18 Bend 15.00 -0.08 375.99 378.15 2.16 0.36 0.0406

19 Drive 25.00 0.00 378.51 178.49 1.61 200.02 0.65 0.0406

20 Int. Pt 44.60 0.08 179.14 179.14 1.19 0.0408

21 Drive 44.60 0.08 180.33 81.85 0.83 98.48 1.19 0.0408

22 Int. Pt 10.00 0.15 83.04 83.04 0.32 0.0412

23 Takeup 26.03 0.50 83.36 83.93 0.57 0.88 0.0412

24 Bend 11.06 -0.52 84.81 85.38 0.58 0.09 0.0412

25 Int. Pt 415.65 0.00 85.47 85.47 10.93 0.0412

26 Int. Pt 641.13 0.00 96.40 96.40 18.43 0.045

27 Int. Pt 367.23 -3.83 114.83 114.83 9.25 0.0458

28 Int. Pt 519.25 -4.50 124.08 124.08 13.12 0.0448

29 Int. Pt 355.62 0.00 137.20 137.20 11.68 0.0514

30 Int. Pt 160.04 6.20 148.88 148.88 7.79 0.0527

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Run Inclines Loaded Page 17/47
Station / Pulley Tensions Visco
Section Section Ten Material Skirt Scraper Section
Length Lift T1 Run T2 Run Tp Drive Adj. Accel. Friction Friction Effective Friction
Station m m kN kN Pulley Te kN kN kN kN kN Tension Factor

31 Int. Pt 93.48 0.00 156.67 156.67 3.21 0.0538

32 Int. Pt 84.10 -4.20 159.88 159.88 1.29 0.0544

33 Int. Pt 282.91 0.00 161.17 161.17 9.87 0.0546

34 Int. Pt 577.95 -0.05 171.04 171.04 20.38 0.0553

35 Int. Pt 263.45 2.35 191.42 191.42 10.50 0.057

36 Int. Pt 102.22 0.00 201.92 201.92 3.84 0.0589

37 Int. Pt 98.45 -3.80 205.76 205.76 2.28 0.0597

38 Int. Pt 10.39 0.08 208.04 208.04 0.30 0.0407

Totals: 9.32 295.22 0.00 1.44 0.00 0.00 286.95

Maximum Tension 378.51 kN Total Effective Tension 300.93 kN
Minimum Tension 81.85 kN Total Belt Power (Te x V) 1564.84 kW
Average Tension Inclines Loaded 217.56 kN Belt Modulus 100800 kN/m
Average Tension Belt Stationary 81.86 kN Total Belt Length 8231.36 m
Average Tension Difference 135.7 kN Belt Elastic Elongation 7.59 m
Takeup Movement 3.795 m
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Run Declines Loaded Page 18/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Station / Pulley Tensions Visco

Section Section Ten Material Skirt Scraper Section
Length Lift T1 Run T2 Run Tp Drive Adj. Accel. Friction Friction Effective Friction
Station m m kN kN Pulley Te kN kN kN kN kN Tension Factor

1 Tail 5.10 0.08 208.34 209.62 1.28 0.16 0.0396

2 Hopper 5.33 0.00 209.78 209.78 1.44 0.13 0.0247

3 Int. Pt 98.45 3.80 211.36 211.36 3.97 0.0247

4 Int. Pt 102.22 0.00 215.33 215.33 2.59 0.0247

5 Int. Pt 263.45 -2.35 217.92 217.92 7.69 0.0323

6 Int. Pt 577.95 0.05 225.61 225.61 21.31 0.0325

7 Int. Pt 282.91 0.00 246.92 246.92 10.72 0.0331

8 Int. Pt 84.10 4.20 257.64 257.64 4.91 0.0339

9 Int. Pt 93.48 0.00 262.55 262.55 3.70 0.0343

10 Int. Pt 160.04 -6.20 266.25 266.25 0.71 0.0346

11 Int. Pt 355.62 0.00 266.96 266.96 14.29 0.0347

12 Int. Pt 505.50 4.50 281.25 281.25 22.40 0.035

13 Int. Pt 380.84 3.83 303.65 303.65 13.79 0.0292

14 Int. Pt 641.13 0.00 317.44 317.44 23.26 0.0319

15 Int. Pt 415.65 0.00 340.70 340.70 15.44 0.0326

16 Int. Pt 64.00 -0.23 356.14 356.14 1.60 0.0243

17 Head 39.12 0.33 357.74 359.88 2.14 1.14 0.0406

18 Bend 15.00 -0.08 361.02 363.18 2.16 0.36 0.0406

19 Drive 25.00 0.00 363.54 173.55 1.63 189.99 0.65 0.0406

20 Int. Pt 44.60 0.08 174.20 174.20 1.19 0.0408

21 Drive 44.60 0.08 175.39 81.85 0.84 93.54 1.19 0.0408

22 Int. Pt 10.00 0.15 83.04 83.04 0.32 0.0412

23 Takeup 26.03 0.50 83.36 83.93 0.57 0.88 0.0412

24 Bend 11.06 -0.52 84.81 85.38 0.58 0.09 0.0412

25 Int. Pt 415.65 0.00 85.47 85.47 10.93 0.0412

26 Int. Pt 641.13 0.00 96.40 96.40 18.43 0.045

27 Int. Pt 367.23 -3.83 114.83 114.83 9.25 0.0458

28 Int. Pt 519.25 -4.50 124.08 124.08 13.12 0.0448

29 Int. Pt 355.62 0.00 137.20 137.20 11.68 0.0514

30 Int. Pt 160.04 6.20 148.88 148.88 7.79 0.0527

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Tension Calculations - Run Declines Loaded Page 19/47
Station / Pulley Tensions Visco
Section Section Ten Material Skirt Scraper Section
Length Lift T1 Run T2 Run Tp Drive Adj. Accel. Friction Friction Effective Friction
Station m m kN kN Pulley Te kN kN kN kN kN Tension Factor

31 Int. Pt 93.48 0.00 156.67 156.67 3.21 0.0538

32 Int. Pt 84.10 -4.20 159.88 159.88 1.29 0.0544

33 Int. Pt 282.91 0.00 161.17 161.17 9.87 0.0546

34 Int. Pt 577.95 -0.05 171.04 171.04 20.38 0.0553

35 Int. Pt 263.45 2.35 191.42 191.42 10.50 0.057

36 Int. Pt 102.22 0.00 201.92 201.92 3.84 0.0589

37 Int. Pt 98.45 -3.80 205.76 205.76 2.28 0.0597

38 Int. Pt 10.39 0.08 208.04 208.04 0.30 0.0407

Totals: 9.32 295.2 0.00 1.44 0.00 0.00 286.95

Maximum Tension 363.54 kN Total Effective Tension 286 kN
Minimum Tension 81.85 kN Total Belt Power (Te x V) 1487.21 kW
Average Tension Declines Loaded 212.85 kN Belt Modulus 100800 kN/m
Average Tension Belt Stationary 81.86 kN Total Belt Length 8231.36 m
Average Tension Difference 130.99 kN Belt Elastic Elongation 7.326 m
Takeup Movement 3.663 m
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
 19 Feb 2018 12:55 Conveyor Starting and Stopping Page 20/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

System Masses Input Data

Mass of Belt 326,135 kg Belt Speed 5.2 m/s
Mass of Material 215,313 kg Belt Rated Tension 209 kN/m
Carry Idler Equivalent Mass 102,867 kg Allow. Belt Start Tension Rise 150 %
Return Idler Equivalent Mass 106,743 kg Drive Inertia 66 kg-m2
Pulley Equivalent Mass 6,789 kg Total Braking Torque 0 kNm
Drive Equivalent Mass 82,912 kg Start-up Factor - Loaded 150 %
Total System Equivalent Mass 840,759 kg Start-up Factor - Empty 150 %
Installed Power 2250 kW
Tensions and Accelerating Forces
Drive Efficiency (Average) 95 %
Effective Tens. Fully Loaded 297.71 kN
Effective Tension Empty 288.73 kN Stopping Times & Deceleration Rates
Total Braking Force 0.00 kN Stopping Time Loaded Braking 14.69 sec
Stopping Time Loaded Coasting 14.69 sec
Tension Available to Accelerate Conveyor
Stopping Time Empty Braking 11.26 sec
Accelerating Tension - Loaded 318.87 kN
Stopping Time Empty Coasting 11.26 sec
Accelerating Tension - Empty 327.86 kN
Deceleration - Loaded Braking -0.35 m/s2
Starting Times & Acceleration Rates
Deceleration - Loaded Coasting -0.35 m/s2
Starting Time - Fully Loaded 13.71 sec
Deceleration - Empty Braking -0.46 m/s2
Starting Time - Empty 9.92 sec
Deceleration - Empty Coasting -0.46 m/s2
Acceleration Rate - Loaded 0.38 m/s2
Accelerating Rate - Empty 0.52 m/s2 Stopping Distances & Discharge Volumes
Stopping Distance Loaded Braking 38.18 m
Belt Tension Rise Starting / Braking
Stopping Distance Loaded Coasting 38.18 m
Max Belt Tension, Start/Brake 658.70 kN
Stopping Distance Empty Braking 29.29 m
Belt Width 1460 mm
Stopping Distance Empty Coasting 29.29 m
Maximum Belt Tension / width 451.16 kN/m
Belt Rated Tension / width 209 kN/m Discharge Mass, Braking 2040 kg
Actual Max Tension, Start/Brake 215.9 % Discharge Mass, Coasting 2040 kg
WARNING: Belt Tension Rise during Starting Discharge Volume, Braking 2.55 m3
Exceeds Allowable Tension Rise Discharge Volume, Coasting 2.55 m3
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
 19 Feb 2018 12:55 Conveyor Idler Details Report Page 21/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Carry Side Idlers Return Side Idlers

Idler Category Helix Pipe Conveyor Helix Pipe Conveyor
Idler Description 1400 Belt 350 Pipe Dia Series 30 6 1400 Belt 350 Pipe Dia
Roll Panel 152 Offset Series 30 6 Roll Panel 152
Offset
Idler Design Belt Width 1460 mm 1460 mm
Idler Series 30 30
Drawing Number
Nominal Idler Spacing 1.2 m 1.2 m
Total Number of Idlers 4034 4186
Idler Price 0 0
Troughing Angle 360.0 deg 360.0 deg
Idler Shaft Diameter 30.0 mm 30.0 mm
Idler Bearing Diameter 25.0 mm 25.0 mm
Number of Idler Rolls 6 6
Idler Roll Diameter 152 mm 152 mm
Idler Rotation Speed 653 rpm 653 rpm
Roll Face Width 222 mm 222 mm
Roll Bearing Centres 157.8 mm 157.8 mm
Shaft Support Centres 245.4 mm 245.4 mm
Idler Support Fixing Width 0 mm 0 mm
Idlerset Rotating Mass 25.5 kg 25.5 kg
Idlerset Total Mass 0 kg 0 kg
Idler Vertical Misalignment Allowance 3.0 mm 5.0 mm
Dynamic Load Factor 1.38 1.40
Belt Deviation Load 500 N 500 N
Total Load on Centre Roll 1,408 N 858 N
Type of Bearing Ball Ball
Bearing Designation 6305 6305
Bearing Dynamic Load Rating C 22,500 N 22,500 N
Bearing L10h Life 832,771 hrs 3,676,730 hrs
Allowable Shaft Deflection at Bearing 8.00 min 8.00 min
Actual Shaft Deflection at Bearing 1.00 min 0.61 min
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 22/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 22/47

Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 23/47
Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %
Station / Sectio Design
Vertical Running Starting Braking Minimum
Load Curve Fully Loaded Empty Fully Loaded Empty Fully Loaded Empty Reqd.
Capacity Radius Tension Radius Radius
Curve Tension Radius Tension Radius Tension Radius Tension Radius Tension Radius
Station Type tonnes/hr m kN m kN m kN m kN m kN m kN m m

1 Tail 208.34 208.34 307.87 345.9 115.42 87.2

2 Hopper 1000 209.78 209.78 309.81 348.03 116.4 88.04

3 Int. Pt Concave 1000 211.38 209.91 311.64 348.33 117.77 88.01

Belt Tension at Curve kN 211.38 209.91 311.64 348.33 117.77 88.01

Min. Concave Lift Off Radius 725 720 1069 1195 404 302 1195
Min. Edge Tension Radius
Max. Centre Tension Radius

4 Int. Pt Convex 1000 300 217.67 213.88 322.35 355.66 119.93 89.02

Belt Tension at Curve kN 217.67 213.88 322.35 355.66 119.93 89.02

0
Min. Edge Tension Radius
Max. Buckling Radius
Belt Edge Tension Rise at Curve kN 0 0 0 0 0 0
Total Edge Tension at Curve kN and % 217.67 71% 213.88 70% 322.35 106% 355.66 117% 119.93 39% 89.02 29%
Centre Tension at Curve kN 217.67 213.88 322.35 355.66 119.93 89.02

5 Int. Pt 1000 220.6 216.47 329.87 361.74 118.57 88.54

6 Int. Pt 1000 228.34 225.16 349.45 379.41 115.26 89.32

7 Int. Pt 1000 250.21 246.47 397.3 420.45 112.87 93.26

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 24/47
Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %
Station / Sectio Design
Vertical Running Starting Braking Minimum
Load Curve Fully Loaded Empty Fully Loaded Empty Fully Loaded Empty Reqd.
Capacity Radius Tension Radius Radius
Curve Tension Radius Tension Radius Tension Radius Tension Radius Tension Radius
Station Type tonnes/hr m kN m kN m kN m kN m kN m kN m m

8 Int. Pt Concave 1000 261.11 257.19 420.92 440.83 111.89 95.47

Belt Tension at Curve kN 261.11 257.19 420.92 440.83 111.89 95.47

Min. Concave Lift Off Radius 896 883 1444 1513 384 328 1513
Min. Edge Tension Radius
Max. Centre Tension Radius

9 Int. Pt Convex 1000 300 268.25 262.1 431.84 448.61 115.5 97.85

Belt Tension at Curve kN 268.25 262.1 431.84 448.61 115.5 97.85

0
Min. Edge Tension Radius
Max. Buckling Radius
Belt Edge Tension Rise at Curve kN 0 0 0 0 0 0
Total Edge Tension at Curve kN and % 268.25 88% 262.1 86% 431.84 142% 448.61 147% 115.5 38% 97.85 32%
Centre Tension at Curve kN 268.25 262.1 431.84 448.61 115.5 97.85

10 Int. Pt Convex 1000 271.98 265.8 439.77 455.49 115.31 98.75

Belt Tension at Curve kN 271.98 265.8 439.77 455.49 115.31 98.75

0
Min. Edge Tension Radius
Max. Buckling Radius
Belt Edge Tension Rise at Curve kN 0 0 0 0 0 0
Total Edge Tension at Curve kN and % 271.98 89% 265.8 87% 439.77 144% 455.49 149% 115.31 38% 98.75 32%
Centre Tension at Curve kN 271.98 265.8 439.77 455.49 115.31 98.75

11 Int. Pt Concave 1000 300 272.75 269.77 447.74 464.93 109.37 97.91

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 25/47
Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %
Station / Sectio Design
Vertical Running Starting Braking Minimum
Load Curve Fully Loaded Empty Fully Loaded Empty Fully Loaded Empty Reqd.
Capacity Radius Tension Radius Radius
Curve Tension Radius Tension Radius Tension Radius Tension Radius Tension Radius
Station Type tonnes/hr m kN m kN m kN m kN m kN m kN m m

Belt Tension at Curve kN 272.75 269.77 447.74 464.93 109.37 97.91

Min. Concave Lift Off Radius 936 926 1536 1595 375 336 1595
Min. Edge Tension Radius
Max. Centre Tension Radius

12 Int. Pt 1000 300 287.08 284.06 478.06 491.36 108.77 101.5

13 Int. Pt 1000 300 311.76 306.46 525.46 531.01 112.23 108.71

14 Int. Pt Convex 1000 328.19 320.25 559.01 557.8 112.68 111.05

Belt Tension at Curve kN 328.19 320.25 559.01 557.8 112.68 111.05

0
Min. Edge Tension Radius
Max. Buckling Radius
Belt Edge Tension Rise at Curve kN 0 0 0 0 0 0
Total Edge Tension at Curve kN and % 328.19 108% 320.25 105% 559.01 183% 557.8 183% 112.68 37% 111.05 36%
Centre Tension at Curve kN 328.19 320.25 559.01 557.8 112.68 111.05

15 Int. Pt 1000 352.0 343.51 611.65 602.95 109.58 115.04

16 Int. Pt 1000 367.73 358.95 646.07 632.58 107.86 117.98

17 Head 369.33 360.47 650.54 636.28 106.77 117.58

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 26/47
Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %
Station / Sectio Design
Vertical Running Starting Braking Minimum
Load Curve Fully Loaded Empty Fully Loaded Empty Fully Loaded Empty Reqd.
Capacity Radius Tension Radius Radius
Curve Tension Radius Tension Radius Tension Radius Tension Radius Tension Radius
Station Type tonnes/hr m kN m kN m kN m kN m kN m kN m m

18 Bend 372.66 363.75 655.36 641.62 108.71 119.05

19 Drive 375.23 366.27 658.7 645.21 110.56 120.62

20 Int. Pt 178.07 175.1 272.05 266.96 93.22 97.29

21 Drive 179.26 176.29 274.34 269.68 93.38 97.13

22 Int. Pt Concave 83.04 83.04 82.79 82.7 84.73 85.25

Belt Tension at Curve kN 83.04 83.04 82.79 82.7 84.73 85.25

Min. Concave Lift Off Radius 285 285 284 284 291 293 293
Min. Edge Tension Radius
Max. Centre Tension Radius

23 Takeup 83.36 83.36 83.36 83.36 83.36 83.36

24 Bend 84.81 84.81 85.73 86.08 83.95 83.68

25 Int. Pt Concave 85.47 85.47 86.92 87.48 84.12 83.71

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 27/47
Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %
Station / Sectio Design
Vertical Running Starting Braking Minimum
Load Curve Fully Loaded Empty Fully Loaded Empty Fully Loaded Empty Reqd.
Capacity Radius Tension Radius Radius
Curve Tension Radius Tension Radius Tension Radius Tension Radius Tension Radius
Station Type tonnes/hr m kN m kN m kN m kN m kN m kN m m

Belt Tension at Curve kN 85.47 85.47 86.92 87.48 84.12 83.71

Min. Concave Lift Off Radius 293 293 298 300 289 287 300
Min. Edge Tension Radius
Max. Centre Tension Radius

26 Int. Pt 96.4 96.4 108.12 112.6 85.46 82.14

27 Int. Pt Convex 114.83 114.83 142.38 152.91 89.11 81.3

Belt Tension at Curve kN 114.83 114.83 142.38 152.91 89.11 81.3

0
Min. Edge Tension Radius
Max. Buckling Radius
Belt Edge Tension Rise at Curve kN 0 0 0 0 0 0
Total Edge Tension at Curve kN and % 114.83 38% 114.83 38% 142.38 47% 152.91 50% 89.11 29% 81.3 27%
Centre Tension at Curve kN 114.83 114.83 142.38 152.91 89.11 81.3

28 Int. Pt 124.08 124.08 160.7 174.7 89.9 79.51

29 Int. Pt 137.2 137.2 186.64 205.54 91.04 77.03

30 Int. Pt Concave 148.88 148.88 207.11 229.36 94.52 78.01

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 28/47
Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %
Station / Sectio Design
Vertical Running Starting Braking Minimum
Load Curve Fully Loaded Empty Fully Loaded Empty Fully Loaded Empty Reqd.
Capacity Radius Tension Radius Radius
Curve Tension Radius Tension Radius Tension Radius Tension Radius Tension Radius
Station Type tonnes/hr m kN m kN m kN m kN m kN m kN m m

Belt Tension at Curve kN 148.88 148.88 207.11 229.36 94.52 78.01

Min. Concave Lift Off Radius 511 511 711 787 324 268 787
Min. Edge Tension Radius
Max. Centre Tension Radius

31 Int. Pt Convex 156.67 156.67 218.85 242.61 98.62 80.99

Belt Tension at Curve kN 156.67 156.67 218.85 242.61 98.62 80.99

0
Min. Edge Tension Radius
Max. Buckling Radius
Belt Edge Tension Rise at Curve kN 0 0 0 0 0 0
Total Edge Tension at Curve kN and % 156.67 51% 156.67 51% 218.85 72% 242.61 80% 98.62 32% 80.99 27%
Centre Tension at Curve kN 156.67 156.67 218.85 242.61 98.62 80.99

32 Int. Pt Convex 159.88 159.88 224.37 249.01 99.68 81.4

Belt Tension at Curve kN 159.88 159.88 224.37 249.01 99.68 81.4

0
Min. Edge Tension Radius
Max. Buckling Radius
Belt Edge Tension Rise at Curve kN 0 0 0 0 0 0
Total Edge Tension at Curve kN and % 159.88 52% 159.88 52% 224.37 74% 249.01 82% 99.68 33% 81.4 27%
Centre Tension at Curve kN 159.88 159.88 224.37 249.01 99.68 81.4

33 Int. Pt Concave 161.17 161.17 227.73 253.17 99.03 80.16

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 29/47
Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %
Station / Sectio Design
Vertical Running Starting Braking Minimum
Load Curve Fully Loaded Empty Fully Loaded Empty Fully Loaded Empty Reqd.
Capacity Radius Tension Radius Radius
Curve Tension Radius Tension Radius Tension Radius Tension Radius Tension Radius
Station Type tonnes/hr m kN m kN m kN m kN m kN m kN m m

Belt Tension at Curve kN 161.17 161.17 227.73 253.17 99.03 80.16

Min. Concave Lift Off Radius 553 553 782 869 340 275 869
Min. Edge Tension Radius
Max. Centre Tension Radius

34 Int. Pt 171.04 171.04 244.59 272.7 102.38 81.52

35 Int. Pt 191.42 191.42 279.25 312.81 109.43 84.53

36 Int. Pt 201.92 201.92 296.25 332.29 113.86 87.11

37 Int. Pt Convex 205.76 205.76 302.61 339.62 115.34 87.88

Belt Tension at Curve kN 205.76 205.76 302.61 339.62 115.34 87.88

0
Min. Edge Tension Radius
Max. Buckling Radius
Belt Edge Tension Rise at Curve kN 0 0 0 0 0 0
Total Edge Tension at Curve kN and % 205.76 67% 205.76 67% 302.61 99% 339.62 111% 115.34 38% 87.88 29%
Centre Tension at Curve kN 205.76 205.76 302.61 339.62 115.34 87.88

38 Int. Pt Concave 208.04 208.04 307.32 345.25 115.36 87.21

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Vertical Curve Radius Calculations Page 30/47
Belt Width 1460 mm % Belt Mass for Lift-off Calculation 75 %
Belt Mass - New Belt 39.62 kg/m Curve Tension Safety Factor 1
Top Cover Mass - New Belt 13.15 kg/m Average Drive Torque Start-up Factor - Loaded 150 %
Bottom Cover Mass 8.22 kg/m Average Drive Torque Start-up Factor - Empty 150 %
Worn Belt Mass 29.72 kg/m Belt Modulus 100800 kN/m
Reduction of Top Cover Mass 75.3 % Belt Rated Tension 209 kN/m 305.1 kN
Conveyed Material Mass 53.42 kg/m Allowable Edge Tension - Running: 115 % Starting 150 %
Station / Sectio Design
Vertical Running Starting Braking Minimum
Load Curve Fully Loaded Empty Fully Loaded Empty Fully Loaded Empty Reqd.
Capacity Radius Tension Radius Radius
Curve Tension Radius Tension Radius Tension Radius Tension Radius Tension Radius
Station Type tonnes/hr m kN m kN m kN m kN m kN m kN m m

Belt Tension at Curve kN 208.04 208.04 307.32 345.25 115.36 87.21

Min. Concave Lift Off Radius 714 714 1055 1185 396 299 1185
Min. Edge Tension Radius
Max. Centre Tension Radius

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and this is larger than 70% recommended. This may result in material
spillage and opeing of the pipe tube and is not recommended. Also, the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph 4km.xml Helix

Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Viscoelastic Friction Factor Report Page 31/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Viscoelastic Calculations Input Data

Belt Rubber Description Rubber description ... Carry Idler Centre Roll Dia 152 mm
Top Cover Dynamic Modulus E' 6 N/mm2 Carry Idler Centre Roll Drag 2 N
Top Cover Dynamic Loss Factor Tan(delta) 0.13 Carry Idler Wing Roll Dia 152 mm
Belt Top Cover Temperature 30 deg C Carry Idler Wing Roll Drag 2 N
Rolling Resistance Factor RRF Top 0.072 RRF Bot. 0.072 Return Idler Centre Roll Dia 152 mm
Bottom Cover Dynamic Modulus E' 6 N/mm2 Return Idler Centre Roll Drag 2 N
Bot Cover Dynamic Loss Factor Tan(delta) 0.13 Return Idler Wing Roll Dia 152 mm
Belt Bottom Cover Temperature 30 deg C Return Idler Wing Roll Drag 2 N
Belt & Material Flexure Adjustment factor 1 Idlerset Skew Angle 0.1 deg
Belt has Turnover on Return Run Idlerset Forward Tilt angle 0.1 deg

Station / Section friction factor f (loaded) Empty

Total Indentation Matl.& Belt Idler Drag Idler Skew & Tilt
Loaded Indent Indent Freq Flexure Flexure Drag Drag Tilt Tilt Empty
Section Idler Friction factor factor uency friction friction factor factor friction friction Friction
No Length Spacing factor f fi % rad/s fm % fr % ft % factor f
1 5.10 1.00 0.0396 0.00646 16.3 1671 0.00045 1.1 0.03088 77.9 0.00183 4.6 0.0396

2 5.33 1.00 0.0247 0.00859 34.8 1257 0.00110 4.5 0.01315 53.3 0.00183 7.4 0.0396

3 98.45 1.00 0.0247 0.00859 34.8 1257 0.00110 4.4 0.01315 53.3 0.00183 7.4 0.0396

4 102.22 1.00 0.0247 0.00859 34.8 1257 0.00108 4.4 0.01315 53.3 0.00183 7.4 0.0396

5 263.45 1.00 0.0323 0.01621 50.2 1257 0.00106 3.3 0.01315 40.8 0.00183 5.7 0.0571

6 577.95 1.00 0.0325 0.01646 50.7 1257 0.00104 3.2 0.01315 40.5 0.00183 5.6 0.0577

7 282.91 1.00 0.0331 0.01716 51.8 1257 0.00099 3.0 0.01315 39.7 0.00183 5.5 0.0593

8 84.10 1.00 0.0339 0.01795 53.0 1257 0.00095 2.8 0.01315 38.8 0.00183 5.4 0.0611

9 93.48 1.00 0.0343 0.01839 53.6 1257 0.00092 2.7 0.01315 38.3 0.00183 5.3 0.0620

10 160.04 1.00 0.0346 0.01866 54.0 1257 0.00091 2.6 0.01315 38.1 0.00183 5.3 0.0625

11 355.62 1.00 0.0347 0.01877 54.2 1257 0.00090 2.6 0.01315 37.9 0.00183 5.3 0.0629

12 505.50 1.00 0.0350 0.01915 54.7 1257 0.00088 2.5 0.01315 37.6 0.00183 5.2 0.0640

13 380.84 1.00 0.0292 0.01339 45.8 1257 0.00084 2.9 0.01315 45.0 0.00183 6.3 0.0506

14 641.13 1.00 0.0319 0.01616 50.6 1257 0.00080 2.5 0.01315 41.2 0.00183 5.7 0.0568

15 415.65 1.00 0.0326 0.01680 51.6 1257 0.00076 2.3 0.01315 40.4 0.00183 5.6 0.0582

16 64.00 1.00 0.0243 0.00859 35.3 1257 0.00073 3.0 0.01315 54.1 0.00183 7.5 0.0395

17 39.12 1.00 0.0406 0.00756 18.6 1429 0.00029 0.7 0.03088 76.1 0.00183 4.5 0.0406

18 15.00 1.00 0.0406 0.00756 18.6 1429 0.00029 0.7 0.03088 76.1 0.00183 4.5 0.0406

19 25.00 1.00 0.0406 0.00756 18.6 1429 0.00029 0.7 0.03088 76.1 0.00183 4.5 0.0406

20 44.60 1.00 0.0408 0.00756 18.5 1429 0.00051 1.2 0.03088 75.7 0.00183 4.5 0.0408

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 f factor - Viscoelastic Calculations Page 32/47
Station / Section friction factor f (loaded) Empty
Total Indentation Matl.& Belt Idler Drag Idler Skew & Tilt
Loaded Indent Indent Freq Flexure Flexure Drag Drag Tilt Tilt Empty
Section Idler Friction factor factor uency friction friction factor factor friction friction Friction
No Length Spacing factor f fi % rad/s fm % fr % ft % factor f
21 44.60 1.00 0.0408 0.00756 18.5 1429 0.00050 1.2 0.03088 75.7 0.00183 4.5 0.0408

22 10.00 1.00 0.0412 0.00756 18.4 1429 0.00091 2.2 0.03088 75.0 0.00183 4.5 0.0412

23 26.03 1.00 0.0412 0.00756 18.4 1429 0.00090 2.2 0.03088 75.0 0.00183 4.5 0.0412

24 11.06 1.00 0.0412 0.00756 18.4 1429 0.00089 2.2 0.03088 75.0 0.00183 4.5 0.0412

25 415.65 1.00 0.0412 0.00756 18.4 1429 0.00088 2.1 0.03088 75.0 0.00183 4.5 0.0412

26 641.13 1.00 0.0450 0.01145 25.4 1429 0.00084 1.9 0.03088 68.6 0.00183 4.1 0.0450

27 367.23 1.00 0.0458 0.01230 26.9 1429 0.00075 1.6 0.03088 67.5 0.00183 4.0 0.0458

28 519.25 1.00 0.0448 0.01143 25.5 1429 0.00068 1.5 0.03088 68.9 0.00183 4.1 0.0448

29 355.62 1.00 0.0514 0.01806 35.1 1429 0.00064 1.2 0.03088 60.1 0.00183 3.6 0.0514

30 160.04 1.00 0.0527 0.01941 36.8 1429 0.00059 1.1 0.03088 58.6 0.00183 3.5 0.0527

31 93.48 1.00 0.0538 0.02049 38.1 1429 0.00057 1.1 0.03088 57.4 0.00183 3.4 0.0538

32 84.10 1.00 0.0544 0.02112 38.8 1429 0.00055 1.0 0.03088 56.8 0.00183 3.4 0.0544

33 282.91 1.00 0.0546 0.02137 39.1 1429 0.00054 1.0 0.03088 56.5 0.00183 3.4 0.0546

34 577.95 1.00 0.0553 0.02202 39.8 1429 0.00053 1.0 0.03088 55.9 0.00183 3.3 0.0553

35 263.45 1.00 0.0570 0.02380 41.7 1429 0.00050 0.9 0.03088 54.2 0.00183 3.2 0.0570

36 102.22 1.00 0.0589 0.02567 43.6 1429 0.00047 0.8 0.03088 52.5 0.00183 3.1 0.0589

37 98.45 1.00 0.0597 0.02656 44.5 1429 0.00045 0.8 0.03088 51.7 0.00183 3.1 0.0597

38 10.39 1.00 0.0407 0.00756 18.6 1429 0.00045 1.1 0.03088 75.8 0.00183 4.5 0.0407

Totals: 8223.05 0.45 0.00 0.00 0

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Conveyor Belt Resonance Report Page 33/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Carry Roll Diameter 152 mm Belt Speed 5.2 m/s

Return Roll Diameter 152 mm Takeup Mass 17000 kg
Belt Resonance +/- Tolerance 2 %
Station / Sectio Running Fully Loaded Belt Resonance
Critical Critical Idler
Start End Belt Transverse Idler Roll Section Idler Idler Spacing
Belt Belt Wave Frequency Excitation Idler Spacing Spacing within

Mode
Station Description
Tension Tension Range Frequency Spacing Start End +/- 10%
kN kN Hz to Hz Hz m m m m

1 Tail Tail 209.62 211.38 36.18 36.34 10.89 1 3.32 3.34 OK

2 Hopper 209.78 217.67 23.46 23.9 10.89 1 2.15 2.2 OK

3 Int. Pt P1 211.38 220.6 23.55 24.07 10.89 1 2.16 2.21 OK

4 Int. Pt P2 217.67 228.34 23.9 24.5 10.89 1 2.2 2.25 OK

5 Int. Pt P5 220.6 250.21 24.07 25.67 10.89 1 2.21 2.36 OK

6 Int. Pt P8 228.34 261.11 24.5 26.23 10.89 1 2.25 2.41 OK

7 Int. Pt P12 250.21 268.25 25.67 26.6 10.89 1 2.36 2.44 OK

8 Int. Pt P13 261.11 271.98 26.23 26.78 10.89 1 2.41 2.46 OK

9 Int. Pt P15 268.25 272.75 26.6 26.82 10.89 1 2.44 2.46 OK

10 Int. Pt P17 271.98 287.08 26.78 27.53 10.89 1 2.46 2.53 OK

11 Int. Pt P19 272.75 311.76 26.82 28.71 10.89 1 2.46 2.64 OK

12 Int. Pt P20 287.08 328.19 27.53 29.47 10.89 1 2.53 2.71 OK

13 Int. Pt P21 311.76 352 28.71 30.53 10.89 1 2.64 2.8 OK

14 Int. Pt P24 328.19 367.73 29.47 31.22 10.89 1 2.71 2.87 OK

15 Int. Pt P25 352.0 369.33 30.53 31.29 10.89 1 2.8 2.87 OK

16 Int. Pt P26 367.73 372.66 31.22 31.43 10.89 1 2.87 2.89 OK

17 Head Head (P28) 371.52 375.23 48.28 48.52 10.89 1 4.43 4.46 OK

18 Bend HT Bend 374.87 178.07 48.5 33.32 10.89 1 4.45 3.06 OK

19 Drive Drive 1 177.42 179.26 33.26 33.43 10.89 1 3.05 3.07 OK

20 Int. Pt 178.07 83.04 33.32 22.6 10.89 1 3.06 2.07 OK

21 Drive Drive 2 81.85 83.36 22.43 22.64 10.89 1 2.06 2.08 OK

22 Int. Pt 83.04 84.81 22.59 22.84 10.89 1 2.07 2.1 OK

23 Takeup Takeup 83.93 85.47 22.72 22.93 10.89 1 2.09 2.11 OK

24 Bend Bend 85.38 96.4 22.92 24.39 10.89 1 2.1 2.24 OK

25 Int. Pt P26 rtn 85.47 114.83 22.93 26.67 10.89 1 2.11 2.45 OK

26 Int. Pt 96.4 124.08 24.39 27.74 10.89 1 2.24 2.55 OK

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Conveyor Belt Flap Report Page 34/47
Carry Roll Diameter 152 mm Belt Speed 5.2 m/s
Return Roll Diameter 152 mm Takeup Mass 17000 kg
Belt Resonance +/- Tolerance 2 %
Station / Sectio Running Fully Loaded Belt Resonance
Critical Critical Idler
Start End Belt Transverse Idler Roll Section Idler Idler Spacing
Belt Belt Wave Frequency Excitation Idler Spacing Spacing within

Mode
Station Description
Tension Tension Range Frequency Spacing Start End +/- 10%
kN kN Hz to Hz Hz m m m m

27 Int. Pt P24 rtn 114.83 137.2 26.67 29.19 10.89 1 2.45 2.68 OK

28 Int. Pt 124.08 148.88 27.74 30.43 10.89 1 2.55 2.79 OK

29 Int. Pt P20 rtn 137.2 156.67 29.19 31.23 10.89 1 2.68 2.87 OK

30 Int. Pt 148.88 159.88 30.43 31.55 10.89 1 2.79 2.9 OK

31 Int. Pt P17 rtn 156.67 161.17 31.23 31.68 10.89 1 2.87 2.91 OK

32 Int. Pt P15 rtn 159.88 171.04 31.55 32.65 10.89 1 2.9 3 OK

33 Int. Pt 161.17 191.42 31.68 34.56 10.89 1 2.91 3.17 OK

34 Int. Pt 171.04 201.92 32.65 35.51 10.89 1 3 3.26 OK

35 Int. Pt P8 rtn 191.42 205.76 34.56 35.84 10.89 1 3.17 3.29 OK

36 Int. Pt 201.92 208.04 35.51 36.04 10.89 1 3.26 3.31 OK

37 Int. Pt 205.76 208.34 35.85 36.07 10.89 1 3.29 3.31 OK

38 Int. Pt 208.04 208.34 36.05 36.07 10.89 1 3.31 3.31 OK

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
 19 Feb 2018 12:55 Takeup Travel Report Page 35/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Takeup Travel
Takeup Type Horizontal Gravity
Auto Calc Takeup Mass
Takeup Mass step increment 1000 kg
Max no. of Calc Increments 100
Takeup Mass kg (Manual 17000 kg
Input)
Takeup Mass Calculated 17000 kg
Takeup Travel Estimate
Safety Margin Top + 0.5 m
Belt Splice Allowance + 2 m
Dynamic Travel Up + 1 m
Dynamic Travel Down + 2 m
Safety Margin Bottom + 0.5 m
Thermal Expansion Distance
Minimum Site Temperature 0 deg
Maximum Site Temperature 45 deg
Belt Expansion co-efficient
1.17E-05
m/m per degree C
Total Belt Length 8231.36 m
Thermal Expansion Distance + 0 m
Permanent Belt Stretch
Permanent Stretch co-
0.15 %
efficient % of Belt Length
Permanent Belt Stretch 0 m
Distance +
Total Takeup Travel Distance 0 m

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Drive Details Report Page 36/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Drive No. 1 Drive Pulley No. 19

Drive Description Head Pulley Condition Moist
Load Share on Drive Pulley 67 % Pulley Lagging Type Ceramic
Starting Torque Factor, Fully Loaded 150 % Belt Wrap Angle 180 º
Starting Torque Factor, Empty 150 % Coefficient of Friction, Running 0.35
Number of Motors on Drive Pulley 2 Drive Factor Cw, Running 0.5
Motor Description Toshiba TIK 750 kW Coefficient of Friction, Starting 0.45
Motor Power Rating 750 kW Drive Factor Cw, Starting 0.32
Motor Voltage 3300 Volts Pulley and Shaft Dimensions
Gearbox Description No Selection Pulley Shell Diameter 1000 mm
Drive Efficiency 95 % Pulley Lagging Thickness 12 mm
Pulley Outside Diameter 1024 mm
Pulley Shaft Diameter at Hub 320 mm
Pulley Shaft Diameter at Brg 320 mm
High Speed Coupling Pulley and Belt Speed
HS Coupling Make Motor Full Load Speed 1760 rpm
HS Coupling Model Required Gearbox Ratio 18.147 :1
Low Speed Coupling Selected Gearbox Ratio 1 :1
LS Coupling Make Required Pulley Speed 96.99 rpm
LS Coupling Model Calculated Pulley Speed for Reducer 1760 rpm
Brake Required Belt Speed 5.2 m/s
Brake Location High Speed Calculated Belt Speed 94.36 m/s
Low Speed Brake Torque Input 0 kNm Drive Inertia
Equiv HS Brake Torque 0 Nm Motor Inertia 22 kg-m2
Holdback High Speed Coupling Inertia 0 kg-m2
Static Analysis Runback Force Fv 3981 N High Speed Brake Disc Inertia 0 kg-m2
Static Analysis Horizontal Force Fh 293729 N Flywheel Inertia 0 kg-m2
Calculated Holdback Torque N/A Nm Gearbox Inertia (HSS) 0 kg-m2
Holdback Required (Yes / No) No Fv>Fh/2 Total Drive Inertia 44 kg-m2
Holdback Torque 3 x Motor FLT 443110 Nm Total Drive Equivalent Mass 55275 kg
Holdback Make Not Installed
Holdback Model

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Drive Details Report Page 37/47

Drive No. 2 Drive Pulley No. 21

Drive Description Head Pulley Condition Moist
Load Share on Drive Pulley 33 % Pulley Lagging Type Ceramic
Starting Torque Factor, Fully Loaded 150 % Belt Wrap Angle 180 º
Starting Torque Factor, Empty 150 % Coefficient of Friction, Running 0.35
Number of Motors on Drive Pulley 1 Drive Factor Cw, Running 0.5
Motor Description Toshiba TIK 750 kW Coefficient of Friction, Starting 0.45
Motor Power Rating 750 kW Drive Factor Cw, Starting 0.32
Motor Voltage 3300 Volts Pulley and Shaft Dimensions
Gearbox Description No Selection Pulley Shell Diameter 850 mm
Drive Efficiency 95 % Pulley Lagging Thickness 12 mm
Pulley Outside Diameter 874 mm
Pulley Shaft Diameter at Hub 260 mm
Pulley Shaft Diameter at Brg 260 mm
High Speed Coupling Pulley and Belt Speed
HS Coupling Make Motor Full Load Speed 1760 rpm
HS Coupling Model Required Gearbox Ratio 15.489 :1
Low Speed Coupling Selected Gearbox Ratio 1 :1
LS Coupling Make Required Pulley Speed 113.63 rpm
LS Coupling Model Calculated Pulley Speed for Reducer 1760 rpm
Brake Required Belt Speed 5.2 m/s
Brake Location High Speed Calculated Belt Speed 80.54 m/s
Low Speed Brake Torque Input 0 kNm Drive Inertia
Equiv HS Brake Torque 0 Nm Motor Inertia 22 kg-m2
Holdback High Speed Coupling Inertia 0 kg-m2
Static Analysis Runback Force Fv 3981 N High Speed Brake Disc Inertia 0 kg-m2
Static Analysis Horizontal Force Fh 293729 N Flywheel Inertia 0 kg-m2
Calculated Holdback Torque N/A Nm Gearbox Inertia (HSS) 0 kg-m2
Holdback Required (Yes / No) No Fv>Fh/2 Total Drive Inertia 22 kg-m2
Holdback Torque 3 x Motor FLT 189100 Nm Total Drive Equivalent Mass 27637 kg
Holdback Make Not Installed
Holdback Model
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Drive Motor Details Report Page 38/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Drive No. 1 Drive Pulley No. 19

Drive Description Head Total Motor Power on Drive 1500 kW
Number of Motors on Drive Pulley 2 Absorbed Power at Pulley 1037.24 kW
Motor Category Toshiba Drive Efficiency 95 %
Motor Description Toshiba TIK 750 kW Absorbed Power at Motor 545.92 kW
Motor Power Rating 750 kW Motor Full Load Speed 1760 rpm
Motor Voltage 3300 Volts Motor Full Load Torque 4840 Nm
Number of poles 4 Motor Full Load Current 155.9 Amps
Motor Frame Size D500LL Motor Efficiency @ Duty Point 94.96 %
Motor Shaft Diameter 90 mm Motor Power Factor @ Duty Pt 0.86
Motor Shaft Height 500 mm Mass of Motor 6400 kg
Motor Inertia 22 kg-m2

Drive No. 2 Drive Pulley No. 21

Drive Description Head Total Motor Power on Drive 750 kW
Number of Motors on Drive Pulley 1 Absorbed Power at Pulley 510.9 kW
Motor Category Toshiba Drive Efficiency 95 %
Motor Description Toshiba TIK 750 kW Absorbed Power at Motor 537.79 kW
Motor Power Rating 750 kW Motor Full Load Speed 1760 rpm
Motor Voltage 3300 Volts Motor Full Load Torque 4840 Nm
Number of poles 4 Motor Full Load Current 155.9 Amps
Motor Frame Size D500LL Motor Efficiency @ Duty Point 94.94 %
Motor Shaft Diameter 90 mm Motor Power Factor @ Duty Pt 0.86
Motor Shaft Height 500 mm Mass of Motor 6400 kg
Motor Inertia 22 kg-m2
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Drive Fluid Coupling Details Report Page 39/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Drive No. 1 Drive Pulley No. 19

Drive Description Head Coupling Size
Number of Motors on Drive Pulley 2 Motor Power Rating 750 kW
Selection Mode Manual Motor Full Load Speed 1760 rpm
Coupling Category Voith Coupling Rated Slip 0 %
Coupling Description No Selection - Direct Drive Peak Torque % 0 % FLT
Coupling Power Rating 0 kW Run-up Torque % (2 sec) 0 % FLT
Min. Required Ramping Time sec Coupling Output Speed 1760 rpm
Max Starting Time 0 sec Mass of Coupling 0 kg

Drive No. 2 Drive Pulley No. 21

Drive Description Head Coupling Size
Number of Motors on Drive Pulley 1 Motor Power Rating 750 kW
Selection Mode Manual Motor Full Load Speed 1760 rpm
Coupling Category Voith Coupling Rated Slip 0 %
Coupling Description No Selection - Direct Drive Peak Torque % 0 % FLT
Coupling Power Rating 0 kW Run-up Torque % (2 sec) 0 % FLT
Min. Required Ramping Time sec Coupling Output Speed 1760 rpm
Max Starting Time 0 sec Mass of Coupling 0 kg
Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Drive Gearbox Details Report Page 40/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Drive No. 1 Drive Pulley No. 19

Drive Description Head Motor Power Rating 750 kW
Number of Motors on Drive Pulley 2 Motor Full Load Speed 1760 rpm
Selection Mode Manual Motor Torque @ FL Speed 4070 Nm
Gearbox Category Flender Motor Torque at Pulley Speed 73848 Nm
Gearbox Description No Selection Gearbox Rated Torque 0 Nm
Type Service Factor Required 1.5
Size Service Factor Calculated 0
Code
Plus Speed Selection Tolerance 5 %
Ratio 1
Minus Speed Selection Tolerance 5 %
Number of Stages 0
Fluid Coupling Slip 0 %
Design Efficiency (Input) 95 % Required Gearbox Ratio 18.147 :1
Gearbox Actual Efficiency % Selected Gearbox Ratio 1 :1
Maximum Input Shaft Speed 1800 rpm Required Pulley Speed 96.99 rpm
Minimum Input Shaft Speed 500 rpm Calculated Pulley Speed for Reducer 1760 rpm
Input Shaft Diameter 0 mm Required Belt Speed 5.2 m/s
Output Shaft Diameter 0 mm Calculated Belt Speed 94.36 m/s
Gearbox Inertia 0 kg-m2 Mass of Gearbox 0 kg

Drive No. 2 Drive Pulley No. 21

Drive Description Head Motor Power Rating 750 kW
Number of Motors on Drive Pulley 1 Motor Full Load Speed 1760 rpm
Selection Mode Manual Motor Torque @ FL Speed 4070 Nm
Gearbox Category Flender Motor Torque at Pulley Speed 63034 Nm
Gearbox Description No Selection Gearbox Rated Torque 0 Nm
Type Service Factor Required 1.5
Size Service Factor Calculated 0
Code
Plus Speed Selection Tolerance 5 %
Ratio 1
Minus Speed Selection Tolerance 5 %
Number of Stages 0
Fluid Coupling Slip 0 %
Design Efficiency (Input) 95 % Required Gearbox Ratio 15.489 :1
Gearbox Actual Efficiency % Selected Gearbox Ratio 1 :1
Maximum Input Shaft Speed 1800 rpm Required Pulley Speed 113.63 rpm
Minimum Input Shaft Speed 500 rpm Calculated Pulley Speed for Reducer 1760 rpm
Input Shaft Diameter 0 mm Required Belt Speed 5.2 m/s
Output Shaft Diameter 0 mm Calculated Belt Speed 80.54 m/s
Gearbox Inertia 0 kg-m2 Mass of Gearbox 0 kg

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.
C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix
4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
 19 Feb 2018 12:55 Brake Details Report Page 41/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Drive / Brake No. 1 Drive Pulley No. 19

Description Head Brake Location High Speed
Load Share on Drive Pulley 67 % Disc Material Mild Steel
Brake Category Svendborg BSFH 200 Disc Diameter 600 mm
Brake Description Svendborg Disc Thickness 30 mm
Caliper BSFH 206 Co-eff of Friction (Pad-Disc) 0.4
Number of Motors on Drive Pulley 2
Caliper Clamping Force Minimum 6000 N
Brake Selection Input Data Caliper Clamping Force Maximum 8300 N
Low Speed Brake Torque Input 0 kNm Pad offset Width W 60 mm
Equiv HS Brake Torque 0 Nm Maximum Air Gap 3 mm
Design Braking Torque Input 1000 Nm Recommended working airgap is 1mm
Selected Brake's Torque Rating 1063 Nm Disc Initial Speed 1480 rpm
Design Stopping Time 10.0 sec Disc Moment of Inertia 3.0 kg-m2
Consecutive No of Stops 3 Required Gearbox Ratio 18.147 :1
Average No of Stops 6 Drive Efficiency 95 %
Ambient Temperature 40 deg C Mass of Caliper 26 kg
Disc Temperature after stops 74 deg C Brake Caliper Price $0.00

Drive / Brake No. 2 Drive Pulley No. 21

Description Head Brake Location High Speed
Load Share on Drive Pulley 33 % Disc Material Mild Steel
Brake Category Svendborg BSFH 200 Disc Diameter 600 mm
Brake Description Svendborg Disc Thickness 30 mm
Caliper BSFH 206 Co-eff of Friction (Pad-Disc) 0.4
Number of Motors on Drive Pulley 1
Caliper Clamping Force Minimum 6000 N
Brake Selection Input Data Caliper Clamping Force Maximum 8300 N
Low Speed Brake Torque Input 0 kNm Pad offset Width W 60 mm
Equiv HS Brake Torque 0 Nm Maximum Air Gap 3 mm
Design Braking Torque Input 1000 Nm Recommended working airgap is 1mm
Selected Brake's Torque Rating 1063 Nm Disc Initial Speed 1480 rpm
Design Stopping Time 10.0 sec Disc Moment of Inertia 3.0 kg-m2
Consecutive No of Stops 3 Required Gearbox Ratio 15.489 :1
Average No of Stops 6 Drive Efficiency 95 %
Ambient Temperature 40 deg C Mass of Caliper 26 kg
Disc Temperature after stops 74 deg C Brake Caliper Price $0.00

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.
C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix
4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Shaft Coupling Report Page 42/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Drive No. 1 Drive Pulley No. 19

Drive Description Head Motor Power Rating 750 kW
Load Share on Drive Pulley 67 % Motor Full Load Speed 1760 rpm
Starting Torque Factor, Fully Loaded 150 % Motor Torque @ FL Speed 4070 Nm
Starting Torque Factor, Empty 150 % Motor Torque at Pulley Speed 73848 Nm
Number of Motors on Drive Pulley 2 Pulley Shaft Diameter at Brg 320 mm
Drive Efficiency 95 %

High Speed Coupling Low Speed Coupling

HS Coupling Category LS Coupling Category
HS Coupling Make LS Coupling Make
HS Coupling Model LS Coupling Model
Coupling Type Coupling Type
Coupling Torque Rating 0 Nm Coupling Torque Rating 0 Nm
Service Factor Required 3.5 Service Factor Required 3.5
Service Factor Calculated 0 Service Factor Calculated 0
Maximum Shaft Bore 0 mm Maximum Shaft Bore 0 mm
Minimum Shaft Bore 0 mm Minimum Shaft Bore 0 mm
Maximum Rotation Speed 99 rpm Maximum Rotation Speed 99 rpm
High Speed Coupling Inertia 0 kg-m2 Low Speed Coupling Inertia 0 kg-m2
Drawing Number Drawing Number
High Speed Coupling Mass 0 kg Low Speed Coupling Mass 0 kg
High Speed Coupling Price 0 Low Speed Coupling Price 0
Fluid Coupling
Direct Drive
Fluid Coupling No Selection - Direct Drive
Fluid Coupling Size

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Shaft Coupling Report Page 43/47

Drive No. 2 Drive Pulley No. 21

Drive Description Head Motor Power Rating 750 kW
Load Share on Drive Pulley 33 % Motor Full Load Speed 1760 rpm
Starting Torque Factor, Fully Loaded 150 % Motor Torque @ FL Speed 4070 Nm
Starting Torque Factor, Empty 150 % Motor Torque at Pulley Speed 63034 Nm
Number of Motors on Drive Pulley 1 Pulley Shaft Diameter at Brg 260 mm
Drive Efficiency 95 %

High Speed Coupling Low Speed Coupling

HS Coupling Category LS Coupling Category
HS Coupling Make LS Coupling Make
HS Coupling Model LS Coupling Model
Coupling Type Coupling Type
Coupling Torque Rating 0 Nm Coupling Torque Rating 0 Nm
Service Factor Required 3.5 Service Factor Required 3.5
Service Factor Calculated 0 Service Factor Calculated 0
Maximum Shaft Bore 0 mm Maximum Shaft Bore 0 mm
Minimum Shaft Bore 0 mm Minimum Shaft Bore 0 mm
Maximum Rotation Speed 99 rpm Maximum Rotation Speed 99 rpm
High Speed Coupling Inertia 0 kg-m2 Low Speed Coupling Inertia 0 kg-m2
Drawing Number Drawing Number
High Speed Coupling Mass 0 kg Low Speed Coupling Mass 0 kg
High Speed Coupling Price 0 Low Speed Coupling Price 0
Fluid Coupling
Direct Drive
Fluid Coupling No Selection - Direct Drive
Fluid Coupling Size

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Conveyor Pulley Shafts Page 44/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Station / Sectio Resul- Calculated Selected

T1 T2 tant T1
Shaft Wrap Run Run Start Defl. Dt. Shaft Brg Brg Shaft
Length Angle Force Dia Dia Dia Dia Ctrs Mass
Station Description mm deg kN kN kN kN mm mm mm mm mm kg
1 Tail 2920 180.0 208.3 209.6 0.4 307.9 247.5 267.5 280 280 2200 1411

17 Head 3020 180.0 369.3 371.5 0.5 650.5 285.6 323.8 340 340 2200 2152

18 Bend 3020 180.0 372.7 374.9 0.4 655.4 286.2 324.8 340 340 2200 2152

19 Drive 3020 180.0 375.2 177.4 0.5 658.7 265.4 304.7 320 320 2200 1907

21 Drive 2860 180.0 179.3 81.8 0.4 274.3 220.0 251.1 260 260 2200 1192

23 Takeup 2800 180.0 83.4 83.9 0.4 83.4 196.9 197.1 200 200 2200 691

24 Bend 2520 10.0 84.8 85.4 0.4 85.7 107.4 87.9 110 90 2200 188

Designers Comments * Denotes manual pulley shaft dimensions entered

This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Conveyor Pulleys Page 45/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Station / Sectio
Face Shaft Brg Shaft Brg Wrap Pulley Pulley & Mom of
Shell Lagging Width Length Ctrs Dia Dia Angle Speed Shaft Inertia
Station Description Dia mm mm mm mm mm mm mm deg rpm Mass kg kgm2
1 Tail 850 12 1700 2920 2200 280 280 180.0 113.6 2573 176.3

17 Head 1000 12 1700 3020 2200 340 340 180.0 97.0 3729 342.9

18 Bend 850 12 1700 3020 2200 340 340 180.0 113.6 3282 193.6

19 Drive 1000 12 1700 3020 2200 320 320 180.0 97.0 3493 336.2

21 Drive 850 12 1700 2860 2200 260 260 180.0 113.6 2363 172.5

23 Takeup 700 12 1700 2800 2200 200 200 180.0 137.2 1555 90.6

24 Bend 700 12 1700 2520 2200 110 90 10.0 137.2 1070 87.4

Designers Comments * Denotes manual pulley dimensions entered

This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Conveyor Pulley Dimensions Page 46/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Station / Sectio
Calc Face Shaft Shaft Brg Pulley & Mom of
Shell Shell t Shell t Lagging OD Width Length Dia Dia Shaft Inertia
Station Description Dia mm mm mm mm mm mm mm mm mm Mass kg kgm2
1 Tail 850 17 24.2 12 874 1700 2920 280 280 2573 176.3

17 Head 1000 22 32.2 12 1024 1700 3020 340 340 3729 342.9

18 Bend 850 17 32.3 12 874 1700 3020 340 340 3282 193.6

19 Drive 1000 22 27.8 12 1024 1700 3020 320 320 3493 336.2

21 Drive 850 17 19.1 12 874 1700 2860 260 260 2363 172.5

23 Takeup 700 20 15.3 12 724 1700 2800 200 200 1555 90.6

24 Bend 700 20 15.4 12 724 1700 2520 110 90 1070 87.4

Designers Comments Belt Width mm 1460

This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies
19 Feb 2018 12:55 Conveyor Pulleys Data Sheet Page 47/47
Helix Technologies Pty Ltd
Project Demo Pipe Conveyor Client ABC Engineering
Project No. Pipe Conveyor Example Prepared By PCB
Conveyor No. Pipe Conveyor PC01 Design Date 19 February 2018

Station / Sectio
Face Brg Drive Wrap Pulley T1 T2 T1 T2
Shell Lagging Width Ctrs Power Angle Speed Run Run Start Start
Station Description Dia mm mm mm mm kW deg rpm kN kN kN kN
1 Tail 850 12 1700 2200 180.0 113.6 208.34 209.62 345.9 347.67
Running Full Starting Empty

17 Head 1000 12 1700 2200 180.0 97.0 369.33 371.52 650.54 653.23
Running Full Starting Full

18 Bend 850 12 1700 2200 180.0 113.6 372.66 374.87 655.36 657.95
Running Full Starting Full

19 Drive 1000 12 1700 2200 1500 180.0 97.0 375.23 177.42 658.7 270.76
Running Full Starting Full

21 Drive 850 12 1700 2200 750 180.0 113.6 179.26 81.85 274.34 80.47
Running Full Starting Full

23 Takeup 700 12 1700 2200 180.0 137.2 83.36 83.93 83.36 84.29
Running Full Starting Empty

24 Bend 700 12 1700 2200 10.0 137.2 84.81 85.38 86.08 87.01
Running Full Starting Empty

Designers Comments
This is a demonstration model of an existing pipe conveyor. The pipe diameter is too small for the load capacity - pipe is 77% full and
this is larger than 70% recommended. This may result in material spillage and opeing of the pipe tube and is not recommended. Also,
the horizontal and vertical curve radii used are 300m - to 580m - this is too small in some cases e.g the 440m radius at P25 and will
cause excessive belt tension rise in the curves. Curve radii should be increased and load decreased. See Curve Calculation for Pipe
Conveyor under Calcs menu in Helix delta-T6.

C:\Users\Peter\Documents\Helix\DeltaT6Rego64bit\Conveyors\Temp\Demo 22 Existing Pipe Conveyor PC01 Coal 1000tph Helix

4km.xml
Ver 6.0.20.3 Licenced to Helix Technologies Technologies