Scribd
Upload
51 views

Modtool Instructions: Auckland Head Office

The document provides instructions for downloading and using ModTool software to configure ModWeigh weighing units. It describes downloading the executable file, connecting to a ModWeigh unit via USB or serial, viewing and editing unit settings such as calibration, and saving configuration files.

Uploaded by

sujit patel
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
51 views

Modtool Instructions: Auckland Head Office

The document provides instructions for downloading and using ModTool software to configure ModWeigh weighing units. It describes downloading the executable file, connecting to a ModWeigh unit via USB or serial, viewing and editing unit settings such as calibration, and saving configuration files.

Uploaded by

sujit patel
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

ModTool Instructions

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
Downloading and running
ModTool comes as a Microsoft Windows ® program that can be run by double clicking the .exe file.
There is no installation needed.

When ModTool starts it creates a couple of folders under the location it was started from. The “LogFiles”
folder contains log files that record the activity of ModTool. The “ModWeighLogFiles” folder is created
when the “Save System Logs” button is used and holds the logs from the ModWeigh units.

To remove ModTool simply delete the exe file and these two folders if they exist.

To download the ModTool exe file open the website ​www.emc.co.nz​ and click the ​Downloads​ button
near the top right. Click ​ModWeigh ​near the center of the page. This opens the ModWeigh downloads
area.

Double click ​Software Tools & Updates ​and then ​ModTool - for MT3 configuration​. From here you
can double click the ModTool6.XXrXX.exe file to download it.

Important: Please note the following caveats when downloading and running ModTool.

Downloading

Depending on which web browser you are using you may need to specify that the file is safe to
download.

In Google Chrome for example you will need to click ​Download​ after which chrome may issue a warning
saying “ModTool6.XXrXX.exe is not commonly downloaded and may be dangerous”.

You will need to click the small button next to ​Discard​ and click ​Keep​, as in the following screen shot.

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
The ModTool6.XXrXX.exe will then be saved to your regular Downloads folder.

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
Running

When you double click the ModTool exe file for the first time you will get the following warning from
Windows.

You will need to click ​More Info ​to run ModTool. This warning only appears the first time after you
download the exe file.

A second screen now appears where you can click ​Run anyway​.

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
Auckland Head Office
56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
Using ModTool

The first step is to connect to the ModWeigh unit. Depending on which type of ModWeigh unit you are
using there are a couple of options.

● A standard USB micro B cable can be used to connect your PC/laptop to the USB port of the
ModWeigh unit. If you are using Windows 10 then it automatically installs the correct drivers. If
you are using Windows 7 or Windows 8 then you will need to download and install the correct
USB drivers from the ModWeigh download area of our website at ​www.emc.co.nz​.
● A MAC cable and MAD adapter can be used with a standard USB to RS232 Serial adapter to
connect the PC/laptop to the COM1 port of the ModWeigh unit.

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
Now you can either set the COM port number using the up/down control next to it and click the ​Connect
button, or you can click the ​Search ​button to automatically search the com ports on your computer until
the ModWeigh unit is found.

Once the ModWeigh unit is connected the Connect button changes to Disconnect and the list of
ModWeigh units is shown in the left hand pane.

To select a unit click on it and information about that unit will be displayed on the right hand side.

There are two operations that can be carried out on all ModWeigh units.

The ​Update All ​button - clicking this button will update the software in all units. This will take a long time
and the units will be restarted at the end of the process.

The ​Save System Logs ​button - clicking this button saves the system logs from all units into a folder
called “ModWeighLogFiles”. This will take a long time.

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
Once a unit has been selected by clicking on it you can see the information about it.

The product information includes the product type, software version, serial number and card number. To
the right of this information is the product type description, in this case the ModWeigh unit is a Weight
Indicator.

The weight (AI1) and output current (AO1) are displayed next and update once per second.

Initially the calibration is locked. The calibration fields are greyed out to show this.

To unlock the calibration click the ​locked ​checkbox. The calibration will then become unlocked and the
fields can then be edited.

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
The weight capacity, AI1 response time, zero, span and limit (only shown for 61 product types) can be
edited.

weight capacity ​- sets the weight capacity. This is equivalent to menu quick key Q2121 in a ModWeigh
display.

AI1 response time ​- use the up/down control to adjust this. This is equivalent to menu quick key
Q22311 in a ModWeigh display.

zero ​- set this to 0 and press the Enter key to zero the weighing system. This is equivalent to menu quick
key Q22321 in a ModWeigh display.

span ​- apply a known weight and press the Enter key to span the weighing system. This is equivalent to
menu quick key Q22322 in a ModWeigh display.

limit ​- OUT9 is driven on when the weight is below the value entered in this field. This is equivalent to
menu quick key Q23524 in a ModWeigh display. Please note that this field is only shown for a 61 Weight
Indicator product type.

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz
The ​Refresh ​button - clicking this button will reload all the calibration fields from the ModWeigh unit.

The ​Save Settings… ​button - clicking this button allows you to save the settings of the selected
ModWeigh unit to a file on your computer. You can choose to either save the normal setup or just the
altered setup (only those settings changed from the default). The “...” button allows you to select the
folder where the settings file will be saved, by default the file is saved in the same folder that ModTool is
started from.

The ​Load Settings… ​button - clicking this button allows you to load the settings back into the selected
ModWeigh unit using a file on your computer. You can choose what to load into the unit from: settings,
macros, memory storage or loadcell calibration. The “...” button allows you to select the file where the
settings will be loaded from.

Auckland Head Office


56 Tarndale Grove, Rosedale, Auckland 0632
PO Box 101444, North Shore, Auckland 0745
Phone 09 415 5110, Fax 09 415 5115
[email protected]​, ​www.emc.co.nz

You might also like