Scribd Logo
Upload

Welcome to Scribd!

  • 250 views

    2-7-ASME Sect. IX-2013-Section of Welder Qual. QW 452.3

    Uploaded by

    Tina Martinez

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    2-7-ASME Sect. IX-2013-Section of Welder Qual. QW 452.3

    Uploaded by

    Tina Martinez
    250 views1 page

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    250 views1 page

    2-7-ASME Sect. IX-2013-Section of Welder Qual. QW 452.3

    Uploaded by

    Tina Martinez

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    2013 SECTION IX

    Table QW-452.3
    Groove‐Weld Diameter Limits
    Outside Diameter Qualified, in.
    Outside Diameter of Test (mm)
    Coupon, in. (mm) Min. Max.
    Less than 1 (25) Size welded Unlimited
    1 (25) to 27/8 (73) 1 (25) Unlimited
    Over 27/8 (73) 27/8 (73) Unlimited

    GENERAL NOTES:
    (a) Type and number of tests required shall be in accordance with
    QW-452.1.
    (b) 27/8 in. (73 mm) O.D. is the equivalent of NPS 21/2 (DN 65).

    Table QW-452.4
    Small Diameter Fillet‐Weld Test
    Qualified
    Outside Diameter of Test Coupon, Minimum Outside Diameter, Thick-
    in. (mm) Qualified, in. (mm) ness
    Less than 1 (25) Size welded All
    1 (25) to 27/8 (73) 1 (25) All
    Over 27/8 (73) 27/8 (73) All

    GENERAL NOTES:
    (a) Type and number of tests required shall be in accordance with QW‐452.5.
    (b) 27/8 in. (73 mm) O.D. is considered the equivalent of NPS 21/2 (DN 65).

    Table QW-452.5
    Fillet‐Weld Test
    Type and Number of Tests
    Thickness of Test Required [QW‐462.4(b) or
    Coupon as Welded, QW‐462.4(c)]
    Type of Joint in. (mm) Qualified Range Macro Fracture
    3
    Tee fillet [Note /16 (5) or greater All base material thicknesses, fillet sizes, and 1 1
    (1)] diameters 27/8 (73) O.D. and over [Note (1)]

    Less than 3/16 (5) T to 2 T base material thickness, T maximum 1 1


    fillet size, and all diameters 27/8 (73) O.D. and
    over [Note (1)]

    GENERAL NOTE: Production assembly mockups may be substituted in accordance with QW-181.2.1. When production as-
    sembly mockups are used, range qualified shall be limited to the fillet sizes, base metal thicknesses, and configuration of the
    mockup.
    NOTES:
    (1) Test coupon prepared as shown in QW-462.4(b) for plate or QW-462.4(c) for pipe.
    (2) 27/8 in. (73 mm) O.D. is considered the equivalent of NPS 21/2 (DN 65). For smaller diameter qualifications, refer to
    QW‐452.4 or QW‐452.6.

    --`,````,,,,``,,````,``,,`,,,`,-`-`,,`,,`,`,,`---
    180
    Copyright ASME International (BPVC)
    Provided by IHS under license with ASME •X Licensee=Zachry Engineering Corp/5964006001, User=Withem, Ronald
    No reproduction or networking permitted without license from IHS Not for Resale, 03/24/2014 13:31:13 MDT

    You might also like