Manual de Servicio Hyundai d4b Foreword.p65

MODEL D4B
SHOP MANUAL
(FOR INDUSTRIAL USE)
FORWORD
We would like to express our sincere gratitude to the patrons who have given us unwavering encouragement.
This manual covers shop manual and parts catalog in one volume for an easy reference of parts list, as
well as contains the accurate and efficient service procedures for HYUNDAI D4B industrial engine.
This manual includes specifications, troubleshooting, removal, installation, disassembly and assembly in
each group and presents component illustrations and descriptions for an easy reference.
Accordingly, thoroughly read this manual, rapidly purchase the required parts and service the engine in
proper methods to extend its life and benefit.
Improper service methods and procedures may shorten the engine life resulting from its low performance.
Hyundai genuine parts are designed and built to provide the best performance in your engine. If your claim
is caused by using non-Hyundai genuine parts or servicing at places not recommended, your warranty is
not available.
Hyundai Motor Co., Inc. makes efforts to enhance quality and build better parts and service data for you.
We want to assist you in every way possible with this manual and your purchase of HYUNDAI engine is
highly appreciated.
March 2004
Hyundai Motor Co., Inc.

Industrial Engine Development Team
(TEL 82-52-280-8221~8223)
O.E.M Parts Export Team

(TEL 82-2-746-0291~0299)
NOTE: Contents and specifications are subject to change according to design changes without notice.
IMPORTANT SAFETY NOTICE
Appropriate service methods and proper repair procedures are essential for the safe, reliable operation of all en-
gines as well as the personal safety during work. This manual provides general directions for the efficient service
methods and procedures.
There are numerous variations in procedure, techniques, tools and parts for servicing engines, as well as in the skill
of the individual technician.
This manual cannot possibly anticipate all such variations and provide advice or cautions as to each.
Accordingly, anyone who departs from the instructions provided in this manual must establish that he comprises
neither his personal safety nor the vehicle integrity by his choice of methods, tools or parts.
NOTE, CAUTION, WARNING
NOTE : Information needed in reference to a repair service.
CAUTION: Information about an activity that could cause damage to the vehicle.
WARNING : Information about an activity that could cause injury or damage to the driver, occupants or
repairman.
[SAFETY INFORMATION]
The following list contains some general warnings that you should follow when you work on an engine.
Always wear safety glasses for eye protection.
Be sure that the ignition switch is always in the OFF position, unless otherwise required by the procedure.
Operate the engine only in a well-ventilated area to avoid the danger carbon monoxide poisoning.
Keep yourself and your clothing away from moving parts when the engine is running, especially the drive belt.
To prevent serious burns, avoid contact with hot metal parts such as the radiator, exhaust manifold, tail pipe,
catalytic converter and muffler.
Do not smoke while working on an engine.
To avoid injury, always remove rings, watches, loose hanging jewelry and loose clothing before beginning to
work on an engine.
Keep hands and other objects clear of the radiator fan.

The fan can be operated with the ignition key in the OFF position. Therefore necessarily disconnect the radiator
fan motor connector.
CONTENTS
1. GENERAL 1-1
2. ENGINE MECHANICAL SYSTEM 2-1
3. LUBRICATION SYSTEM 3-1
4. COOLING SYSTEM 4-1
5. INTAKE AND EXHAUST SYSTEM 5-1
6. ENGINE ELECTRICAL SYSTEM 6-1
7. FUEL SYSTEM 7-1

CHAPTER 1 GENERAL INFORMATION
1. GENERAL ............................................................................. 1- 1
2. ENGINE IDENTIFICATION NUMBER ..................................... 1- 6
3. TIGHTENING TORQUE OF STANDARD PARTS.................... 1- 7
4. RECOMMENDED LUBRICANTS AND CAPACITIES .............. 1- 8
5. SPECIFICATIONS .................................................................. 1- 9
6. TORQUE SPECIFICATIONS .................................................. 1- 13
7. SPECIAL TOOLS ................................................................... 1- 15
8. TROUBLESHOOTING ........................................................... 1- 18
9. CHECKING POINT ................................................................. 1- 20

GENERAL 1-1
1. OVERALL
1) ENGINE
Cylinder head is made of aluminum alloy and combustion chamber is a swirl type.
Valve is a SOHC type and the camshaft is operated by the Cog type timing belt.
Cylinder block is made of special cast iron and dry cylinder liner is press-fitted in the cylinder. Water jacket is a Siamese type
and piston is made of aluminum alloy and connected with connecting rod by full floating piston pin.
Oil ring no.1 of the piston ring is made of steel, no.2 of special cast iron, piston ring no.1 of barrel face, no.2 of taper face and
oil ring of bevel cutter and coil expander is attached.
ENGINE ASSEMBLY
KD4BB01A
Crankshaft is made of forged steel and supported with main bearing. Pulley attached with torsional damper is installed in the
front of crankshaft and flywheel in the rear of it. Silent shaft is installed to both ends of the cylinder block, operated with cog
belt and rotated at a double speed of crankshaft.
1-2 GENERAL
Timming belt train
KD4BB02A
GENERAL 1-3
2) LUBRICATION SYSTEM
It is a forced lubrication system and the forced oil by the oil pump is sent to the engine compartment through the oil cooler and
oil filter as shown in the illustration and directly operated by the crank shaft.
Maximum oil pressure is controlled by the reducing valve.
Rocker arm shaft
Camshaft
Main
passage
Oil filter
Left silent shaft
To oil pan
Reduing pressure
Crank shaft
Vaccum pump
Right silent shaft
Oil jet
KD4BB03A
1-4 GENERAL
Oil filter is a combined type and full flow filter and bypass filter are built in it. The bypass filter in the full flow filter uses a thick
multi-fiber media to filter dirt (soot).
If oil enters the oil filter, filtered oil from the full flow filter passes through the main passage and the filtered oil from the bypass
filter returns to the oil pan.
Bypass filter
Gasket
Flow filter
From oil pump
To oil pan
Valve
To main passage
KD4BB04A
GENERAL 1-5
3) COOLING SYSTEM
Engine is cooled with the circulated coolant forced by the water pump.
This illustration shows the flow of coolant.
Cold engine
From heater
To heater
Thermostat
Water pump
Water pipe
From heater
Hot engine
Heater
Thermostat
Water pump
Water pipe
KD4BB05A
1-6 ENGINE IDENTIFICATION NUMBER
2. ENGINE INDENTIFICATION NUMBER

1) ENGINE IDENTIFICATION NUMBER LOCATION
The engine identification number is stamped on the right front
side of the top edge of the cylinder block.
Engine
identification
number
2) DESCRIPTION OF ENGINE IDENTIFICATION KAXD010C
NUMBER
D 4 B B 2 0 0 0 0 0 0
Engine fuel
- D : diesel
Engine range
- 4 : In line 4 cycle 4 cylinder
Engine development order

- B : 4D56
Engine capacity
- F : 2476 cc TC
- H : 2476 cc TCI
- B : 2607 cc NA
Production year
- 1 : 2001
- 2 : 2002
- 3 : 2003
- 4 : 2004
Engine production sequence number

- 000000 ~ 999999
TIGHTENING TORQUE TABLE OF STANDARD PARTS 1-7
3. TIGHTENING TORQUE TABLE OF STANDARD PARTS
Bolt nominal Torque (kg m)

Pitch (mm)
diameter (mm) Head Mark 4 Head Mark 7
EADA010R EADA010S EADA010T EADA010U
M5 0.8 0.3 ~ 0.4 0.5 ~ 0.6

M6 1.0 0.5 ~ 0.6 0.9 ~ 1.1
M8 1.25 1.2 ~ 1.5 2.0 ~ 2.5
M10 1.25 2.5 ~ 3.0 4.0 ~ 5.0
M12 1.25 3.5 ~ 4.5 6~8
M14 1.5 7.5 ~ 8.5 12 ~ 14
NOTE
1. The torques shown in the table are standard values under the following conditions.
. Nuts and bolts are made of steel bar, and galvanized.
. Galvanized plain steel washers are inserted.
. All nuts, bolts and plain washers are dry.
2. The torques shown in the table are not applicable.

. When spring washers, toothed washers and the like are inserted.
. If plastic parts are fastened.
. If self-tapping screws or self-locking nuts are used.
3. If you reduce the torques in the table to the percentage indicated below, under the following conditions,
it will be the standard value.
. If spring washers are used : 85%
. If threads and bearing surfaces are stained with oil : 85%
1-8 LUBRICANTS CAPACITES
4. LUBRICANTS CAPACITES
Description Capacities Specified oil
Oil pan 0.7 l
Oil filter 0.5 l Above API CD or SG

Engine oil (10W/30 or 1500W/40)
Oil cooler 9.5 l
Total 0.7 l
Coolant Antifreeze for aluminum
CAUTION
For the best performance and maximum protection of all types of operation, select only those lubricants
which :
1. Satisfy the requirements of the API classification.
2. Have the proper SAE grade number for expected ambient temperature range.Lubricants which do not
have both an SAE grade number and an API service clasification on the container should not be used.
SPECIFICATIONS 1-9
5. SPECIFICATIONS
Description Specification Limit
Type Diesel engine

Number of cylinders 4
Valve system OHC
D4BB D4BF, D4BH
Total displacement
2607cc 2476cc
Cylinder bore 91.1 mm 91.1 mm

General Cylinder stroke 100 mm 95 mm
Comprssion ratio 22 21
Intake valve
- OPEN 20° BTDC
- CLOSE 48° ATDC
Valve timing
Exhaust valve
- OPEN 54° BTDC
- CLOSE 22° ATDC
Firing order 1-3-4-2

Flatness of gasket surface 0.05 mm 0.2 mm
Flatness of manifold mounting surface 0.15 mm 0.3 mm
Overall height 94.0 ~ 94.1 mm
Oversize of valve guide hole
0.05 13.050 ~ 13.068 mm
Cylinder head Rework dimensions
0.25 13.250 ~ 13.268 mm
(both intake and exhaust)
0.50 13.500 ~ 13.518 mm
Oversize rework dimen-
sions of intake valve seat 0.30 43.300 ~ 43.325 mm
hole 0.60 43.600 ~ 43.625 mm
Oversize rework
dimensions of exhaust 0.30 37.300 ~ 37.325 mm
valve seat hole 0.60 37.600 ~ 37.625 mm
Intake 37.05 mm 36.55 mm
Cam height
Exhaust 37.05 mm 36.55 mm
Camshaft Journal O.D. 29.935 ~ 29.950 mm

Oil clearance 0.05 ~ 0.08 mm
End play 0.1 ~ 0.2 mm
I.D 18.910 ~ 18.928 mm
Rocker arm
Rocker arm - to -guide clearance 0.012 ~ 0.050 mm
1-10 SPECIFICATIONS
O.D. 18.878 ~ 18.898 mm

Rocker shaft
Length 451.5 mm
Intake 136.5 mm
Over length
Exhaust 136.5 mm
Intake 7.960 ~ 7.975 mm

Stem diameter
Exhaust 7.930 ~ 7.950 mm
Valve Fage angle 45° ~ 45° 3 0 ”
Thickness of valve head Intake 2 mm 1.0 mm

(Margin) 2 mm
Exhaust 1.0 mm
Stem-to-guide clear- Intake 0.03 ~ 0.06 mm

ance Exhaust 0.05 ~ 0.09 mm
Free height 49.1 mm
Valve spring Load/Installed N kg/mm 276/40.4
height Out-of squareness Max 2°
Intake 71 mm
Over length
Exhaust 74 mm
I.D. 8.000 ~ 8.018 mm
Valve guide
O.D. 13.06 ~ 13.07 mm
Press temperature Ordinary temperature
Seat angle 45°
Valve seat Valve contack widht 0.9 ~ 1.3 mm
Sinkage 0.2
Right
- Front 18.300 ~ 18.467 mm

- Rear 42.975 ~ 42.991 mm
Journal diameter
Silient shaft Left
- Front 18.959 ~ 18.980 mm
- Rear 49.975 ~ 42.991 mm
Front 0.02 ~ 0.06 mm

Oil clearance
Rear 0.05 ~ 0.09 mm
SPECIFICATIONS 1-11
O.D. 79.0 ~ 79.2 mm
TC NA
Piston-to cylinder clearance 0.04 ~ 0.06 0.03 ~ 0.05
Piston
No. 1 ring 2.601 ~ 2.603 2.02 ~ 2.04
Ring groove width No. 2 ring 2.100 ~ 2.102 2.07 ~ 2.09
Oil ring 4.010 ~ 4.035 3.01 ~ 3.035
No. 1 ring 0.35 ~ 0.50 0.25 ~ 0.40 0.8 mm

End gap No. 2 ring 0.41 ~ 0.54 0.45 ~ 0.60 0.8 mm
Oil ring 0.25 ~ 0.45 0.20 ~ 0.40 0.8 mm

Piston ring
Ring-to-ring No. 1 ring 0.056 ~ 0.076 0.03 ~ 0.07 0.15 mm
groove No. 2 ring 0.046 ~ 0.066 0.08 ~ 0.12 0.15 mm
clearance Oil ring 0.02 ~ 0.065 0.02 ~ 0.065 0.1 mm
Piston pin O. D. 28.994 ~ 29.000 mm
Big end center-to small end center length bend 157.95 ~ 158.05 mm
Bend 0.05
Connecting rod
Twist 0.1
Bing end side clearance 0.1 ~ 0.25 mm
End play 0.05 ~ 0.18 mm 0.2 mm

Journal O.D. 66 mm 0.3 mm
Pin O.D. 53 mm
Out of roundness of journal and pin 0.05 mm less than
Out-of taper of journal and pin 0.015 mm less than
Oil clelarance of journal 0.02 ~ 0.05 mm 0.1 mm

Crank shaft Oil clearance of pin 0.02 ~ 0.05 mm
0.25 U.S. 65.735 ~ 65.750 mm
Journal 0.50 U.S. 65.485 ~ 65.500 mm
0.75 U.S. 65.235 ~ 65.250 mm
0.25 U.S. 52.735 ~ 52.750 mm
Pin 0.50 U.S. 52.485 ~ 52.500 mm
0.75 U.S. 52.235 ~ 52.250 mm

1-12 SPECIFICATIONS
O. D. 91.10 ~ 91.13 mm
Cylinder block Flatness of gasket surface 0.05 mm 0.1 mm
Overall height 318.45 ~ 318.55 mm

Flywheel Run out 0.13 mm 0.13 mm
Inner gear 0.22 ~ 0.35 mm 0.5 mm

Tip clearnace
Outer gear 0.12 ~ 0.22 mm 0.4 mm
Oil pump Body clearnace Side clearance 0.04 ~ 0.10 mm 0.15 mm
Inner gear 0.03 ~ 0.09 mm 0.15 mm

Side clearance
Outer gear 0.12 ~ 0.22 mm 0.30 mm
Cooling system Water-cooled forced circulation system

Drive Belt V Belt
Water pump type Centrifugal impeller
Fan clutch type Bimetal thermostat type
Thermo type Wax type
Coolant temperature gauge unit Thermister type
Thermo switch(113°C, A/con) Thermister type
Cooling system Drive belt 10 ~ 13 mm

Valve opening
76.5 2°C / 82 2°C
temperature
Thermostat
Fulley opening
95°C
temperature
Repeat amount 8 or not less than
Coolant temperature 90.5 ~ 117.5 /70°C

Coolant tempera-
ture gauge unit gauge element 21.3 ~ 26.3 /115°C
Resistance
Glow control 22.3 ~ 27.3k /-20°C
element 2.92 ~ 3.58k /20°C
Intake & Air cleaner Paper filter type

Exhaust Muffler Expansion resonance type
TORQUE SPECIFICATIONS 1-13
6. TORQUE SPECIFICATIONS
Deseription Standard (kg m)
Crankshaft pulley bolt 17 ~ 19
Crankshaft sprocket bolt 6.5 ~ 7.5
Timing belt tensioner bolt 2.2 ~ 3.0
Injection pump sprocket nut 8~9
Silent shaft sprocket nut 3.4 ~ 4.0
Timing belt tensioner “ B ” nut 2.2 ~ 3.0
Rocer cover bolt 0.5 ~ 0.7
Rocker arm shft bolt 1.9 ~ 2.1
Cold engine 10.5 ~ 11.5

Cylinder head bolt
Hot engine 11.5 ~ 12.5
Oil pan bolt 0.6 ~ 0.8
Oil pan drain plug 6~8
Front case bolt (upper, lower) 1.2 ~ 1.5
Silent shaft driven gear bolt 3.4 ~ 4.0
Silent shaft plug gap 2.0 ~ 2.7
Silent shaft gear cover bolt 1.5 ~ 1.8
Connecting rod cap nut 4.5 ~ 4.8
Flywheel bolt 13 ~ 14
Crankshaft bearing cap bolt 7.5 ~ 8.5
Silent shaft chamber cover bolt 0.5 ~ 0.7
Oil relief valve plug 3.0 ~ 4.5
Oil pump cover bolt 0.9 ~ 1.4
Oil pressure switch 0.8 ~ 1.2
Oil filter bracket 1.2 ~ 1.5
Oil cooler by-pass valve 5.0 ~ 6.0
Oil jet check valve 3.0 ~ 3.5
Water pump bolt 1.2 ~ 1.5
Water pump pulley bolt 1.0 ~ 1.2

1-14 TORQUE SPECIFICATIONS
Deseription Standard (kg m)
Water outlet fitting attaching bolt 1.0 ~ 1.3
Coolant tempeature gauge unit 3.0 ~ 4.0
Thermo switch (113°) 0.9
Alternator brace bolt 1.2 ~ 1.5
Adjust rocker arm 1.2 ~ 1.5
Alternator support bolt nut 2.0 ~ 2.5
Intake fitting bolt 1.0 ~ 1.3
Intake manifold bolt 1.5 ~ 2.0
M6 0.8 ` 1.0
Heat protector bolt
M8 1.2 ~ 1.5
Oil return pipe bolt 0.8 ~ 1.0
Exhaust fitting nut 5.0 ~ 7.0
Turbo charger nut 5.0 ~ 7.0
Exhaust manifold nut 1.5 ~ 2.0
SEALANTS
Description Sealants Amount
Half circle packing 3M ATR P/No. 8660 or equivalent As required
Oil pan gasket 3M ATR P/No. 8660 or equivalent As required
Coolant gauge unit 3M nut rocking P/No. 4171 or equivalent As required
Thermo switch (113°, A/con) Threebond No.2440 or equivalent As required

SPECIAL TOOLS 1-15
7. SPECIAL TOOLS
Tool (Number and name) Illustration Use
Silent shaft bearing puller Removal of silent shaft rear bearing

(09212-43100)
B1243100
Silent shaft bearing installer Installation of silent shaft rear bearing

(09212-43200)
B1243200
Bearing installer stopper Removal of Right silent shaft rear bear-

(09212-43300) ing
B1243300
Crank shaft front oil seal installer Installation of crankshaft front oil seal
(09214-32000)
B1432000
Crankshaft front oil seal guide Guide for installation of crank shaft front
(09214 - 32100) oil seal
B1621100
Connecting - rod small - end busing Replacement of connecting - rod small -

replacement tool end bushing
(09214-43000)
B1443000
Camshaft oil seal installer Installation of camshaft oil seal

(09221-21000)
ECLA002I
1-16 SPECIAL TOOLS
Cylinder head bolt wrench Loosening and tightening of cylinder

(09221-32000) head bolt
ECLA002A
Valve seat cutter pilot Correction of valve seat

(09221-43200)
ECLA002B
Valve seat cutter 45° Correction of valve seat

(09221-43300)
ECLA002C

(09221-43400)
ECLA002D

(09221 - 43500)
ECLA002E
Valve spring compressor Compression of valve spring

(09222-21000)
B2221000
Valve stem seal installer Installation of valve stem seal

(09222-32100)
B2232100
SPECIAL TOOLS 1-17
Valve guide installer Removal and Installation of valve

(09222-32200) guide
ECLA002F
Silent shaft drive gear oil seal guide Installation of silent shaft drive oil seal
(09222-43200)
B2243200
Crankshaft rear oil seal installer Installation of crankshaft rear oil seal
(09232-32000)
B3132000
Oil pressure switch wrench Removal and Installation of oil pres-

(09260-32000) sure switch
B6032000
Injection pump sprocket puller Removal of injection of pump sprocket

(09314-43000)
C1443000
1-18 TROUBLESHOOTING
8. Troubleshooting
Symptom Probable cause Remedy
Low compression Blown cylinder head gasket Install new head gasket
Worn or broken piston rings Hone cylinder bores and install new rings
Warped or pitted valves Install new valve
Excessive run-out of valve seats on valve faces Reconditioning valve seats and valves
Noisy valves Incorrect of valve cleanrance Adjust as standard and valve
Worn valve guides Install new valves and/or new valve guides with O.S.
Connecting rod Excessive camshaft end play Reconditioning valve seats and valve
noise
Insufficient oil supply Correct end play
Low oil pressure Check engine oil level
Check engine oil level
Thin or diluted oil Inspect oil relief valve and spring
Excessive bearing clearance Change oil to correct viscosity
Connecting rod journals out-of-roundness Measure bearings for correct clearance
Misaligned connecting rods Replace crankshaft or regrind journals
Replace bent connecting rods
Crankshaft Insufficient oil supply Check engine oil level
Bearing noise Low oil pressure Check engine oil level
Inspect oil relief valve and spring.
Thin or diluted oil Change oil to correct viscosilty
Excessive end play Measure bearings for correct clearances
Crankshaft journal out-of-roundness worn Replace crankshft or regrind journals
Loosen flywheel Tighten to correct torque
Piston noise Excessive clearance due to cylinder wear Correct cylinder wear
Piston or piston pin worn Replace piston
Burnt piston Install new piston
Piston ring damaged Install new rings

TROUBLESHOOTING 1-19
Oil leak Oil pan drain plug loose Tighten to torque
Oil pan mounting bolt loose Tighten to torque
Oil pan gasket broken Install new oil seal
Crankshaft front oil seal defective Install new oil seal
Crankshaft front oil seal defective Install new oil seal
Rocker cover gasket broken Install new oil seal
Oil filter loose Tighten to torque
Oil filter gasket broken Install new oil seal
Oil consumption Worn, scuffed, or broken rings Hone cylinder bores and install new rings
Carbon in oil ring slot Install new rings
Ring fitted too tight in grooves Remove the rings. Check grooves. If groove
width is not , proper width, replace pistion.
Faulty valve stem seals Install new valve stem selas
Overheat Low oil level Check engine oil level
Slow idle speed Set idle speed to specification
Faulty oil pressure switch Install new switch
Colgged oil filter Install new oil filter
Worn parts in oil pump Replace worn parts or pump
Thin or diluted oil Change oil to correct viscosity
Excessive bearing clearance Measure bearings for correct clearance
Oil relief valve stuck Remove valve and inspect, clean and reinstall
Oil pump cover bent or cracked Install new oil pump
Oil screen loose or clogged Clean or replace screen
Insufficent coolant Radiator leakage Correct or replace
Loose or damage radiator hose, heater hose Retighten or replace
Themostat water pump leakage Retighten or replace
Radiator clogged Coolant dirty Replenish
Damaged radiator cap Replace

High coolant tem- Damaged themostat Replace
perature
Loose or broken belt Correct or replace
1-20 CHECKING POINT
9. CHECK POINT
CHECKING COOLANT RESERVIOR
1. Use an adapter to attach the cap to the tester.
2. Increase the pressure until the gauge stops moving. Check

that the pressure level is maintained at or above the limit.
Main valve opening pressure 0.75 ~ 1.05 kgf/cm2
Main valve closing pressure 0.65 kgf/cm2
3. Replace the radiator cap if the reading does not remain at or

above the limit.
NOTE
Be sure that the cap is clean before testing, since rust
or other foreign material on the cap seal will cause
an incorrect reading.
CHECKING COOLANT
1. Check that the coolant level of the reservoir tank is between
FULL and LOW marks.
2. Check that the coolant is not mixed with oil.
3. The standard coolant concentration range is as below.
Standard 30 ~ 60% (normal range)
CAUTION
If the concentration of coolant falls below 30% or
above 60%, vapor corrosion is not inhibited, cool-
ing is not efficient or the engine part could become
damaged or not work properly.
3. Antifreeze ratio
Delivery Freezing Coolant quantity (9.5l )

condition temperature(°C) Mixture ratio(%) Antifreeze
quantity(l)
-15 30 10
40% -20 35 2.45
-25 40 2.80
CHECKING POINT 1-21
REPLACE COOLANT
1. Loosen and remove the drain plug.
2. Remove the reservoir tank and drain coolant.
3. After draining the coolant, pour water into the coolant reser-
voir cap and clean the coolant passage.
4. Securely tighten the radiator drain plug.
5. Install the reservoir tank.
6. Fill the reservoir tank up to FULL line with coolant.
3.9l Engine capacity

Coolant
quantity Overall capacity including
9.5l
the reservoir tank and radiator
7. Securely install the coolant reservoir cap.
8. Check the coolant quantity after warming up the engine and

add coolant.
CAUTION
Do not open the coolant reservoir cap when it is hot.
Steam and scalding liquids released from a hot cool-
ing system can burn you badly.
CHECKING ENGINE OIL LEVEL

1. Pull out the engine oil indicator(dipstick) and wipe it clean
with clothing.
2. Insert the indicator into the oil level gauge guide. Good
3. Remove the indicator carefully and check that the oil level is
between LOW and HIGH marks as shown in the illustration. HIGH
CAUTION LOW
• Make sure the vehicle is on a level ground. KCMB018A
• If the engine is running, turn the engine off and
wait a few minutes before checking.
4. If the oil level is below the LOW mark, add enough recom-
mended oil.
Engine oil Diesel Above API CD SAE 10W30
CAUTION
Oil levels above the HIGH mark may cause engine
damage.
5. After starting the engine, let it idle for a few minutes, stop the
engine and recheck the engine oil level is within the normal
range.
1-22 CHECKING POINT
REPLACING ENGINE OIL

CAUTION
When replacing engine oil and oil filter, do not drop
engine oil in the alternator. Engine oil placed in the
alternator may harm the alternator.
Drain plug
1. After warming up the engine, remove the oil filler cap.

Front
KD4B1001
2. Remove the drain plug and drain oil.
CAUTION
Protect yourself from the hot oil.
3. Tighten the drain plug.
4. Add new oil to the oil filler.
CHECKING AND ADJUSTING DRIVE BELT

Belt
TENSION Water pump
1. Inspect tension by pressing in the middle of belt with 10 kg

f as shown in the illustration.
Standard
Alternator
Alternator 10 ~ 13 mm
Crank shaft KD4B1002
CHECKING AND ADJUSTING DRIVE BELT Alternator

TENSION
CAUTION Alternator bolt
Inspect tension after rotating the engine to one turn
counterclockwise.
Alternator pully
Alternator
support bolt
Crankshaft pulley or pulley
KCMB020B
CHECKING POINT 1-23
BELT ADJUSTMENT Alternator brake bolt

1. Loosen the alternator support nut.
Water pump
pully
2. Loosen the alternator brace bolt.
Alternator
3. Move the alternator to increase the belt tension to the stan- pully
dard value. Crank shaft
pully
Standard 10 ~ 13 mm Alternator
support bolt
KCMB020E
4. When using a tension gauge, move the alternator to the stan-

dard tension value. 10kg.m
·
Water pump
Standard pully
Alternator
50 ~ 70 kg pully
Standard 40 kg
Crank shaft
pulley
KCMB020F
VALVE CLEARANCE ADJUSTMENT

1. Warm up the engine until the coolant temperature reaches
80~90°C.
2. Measure the valve clearance at arrow positions shown in

the illustration.
NO.1 NO.2 NO.3 NO.4
Description Hot engine
Exhaust valve 0.25 mm
Intake valve 0.25 mm

Intake valve
Èí±â¹ëºê
Exhaust valve
¹è±â¹ëºê
KD4B1003
1-24 CHECKING POINT
3. If the measured value exceeds the standard, loosen the

locker arm nut and adjust clearance with the adjust screw Cygnus
turning using a thickness gauge. gauge
4. Tighten the lock nut to the specified torque with the adjust-
ing nut fixed not to rotate using a screwdriver.
5. Rotate the crankshaft to 360° place the cylinder no.4 to

the dead point.
KD4B1004
6. Measure valve clearance at arrow positions shown in the

illustration.
NO.1 NO.2 NO.3 NO.4
( ) : Cold engine
Item Hot engine
Exhaust valve 0.25 (0.15) mm
Intake valve 0.25 (0.15) mm

Intake valve
Exhaust valveÈí±â¹ëºê
¹è±â¹ëºê
7. If the measured value exceeds the standard, adjust it as the KD4B1005
procedures (6)~(7).
8. Inspect clearance of the intake and exhaust valves and ad-

just it if required.
Feeler gauge
Standard 0.25 mm
KCMB020G
VALVE CLEARANCE ADJUSTMENT

Pressure gauge
1. Check the engine oil, starter and battery for normal operation.
2. Warm up the engine until the coolant temperature reaches

80~90°C.
3. Engage the gauge adapter and install the preheat plug to the
pressure gauge.
KCMB025A
CHECKING POINT 1-25
4. Crank the engine and measure the pressure.
Limit (250rpm) 19.2 kg/cm2
5. Check that the measured value of each cylinder is within the

limit.
Limit 3.0 kg/cm2
CHECKING COMPRESSED PRESSURE

1. Disassemble the timing belt upper cover. Timing mark
2. Rotate the crankshaft clockwise to place the cylinder no.1 to

the dead point. Check that the timing mark on the sprocket is
aligned.
No.1 cylinder dead
point
KCMB026A
3. Loosen the spiral bolt to a turn and the groove nut to 1-2
turns.
Groove bolt
Spiral bolt
KCMB026B
4. Rotate the crankshaft clockwise to the second gear of the

camshaft sprocket. Cam shaft sprocket
5. Fix the tensioner groove bolt and tighten the spiral bolt to the
specified torque.
Tightening torque 2.2 ~ 3.0 kg m

Second gear
KCMB026C
1-26 CHECKING POINT
6. Rotate the crankshaft counterclockwise to align it to the tim-

ing mark.
7. Check the belt tension by pressing the middle of cam sprocket

and injection pump sprocket with hand.
Standard 4 ~ 5 mm
8. Assemble the timing belt upper cover.

ECLA005E
ADJUSTING TIMING BELT "B" TENSION

1. Disassemble the timing belt upper cover.
2. Rotate the crankshaft clockwise to place the cylinder no.1 to

the dead point.
KCMB026F
3. Remove the access cover.
Access cover
KCMB026D
4. Loosen the spiral bolt to a turn and the groove nut to 1-2
turns.
5. First tighten the tensioner groove bolt and then the spiral bolt
to the specified torque. Spiral bolt
Tightening torque Groove nut

Bolt 2.0 ~ 2.7 kg m
Nut 2.2 ~ 3.0 kg m

KCMB026E
6. Assemble the access cover.
7. Install the timing belt upper cover.

CHECKING POINT 1-27
CHECKING INJECTION TIMING

1. Stop the cold starting advance angle function. Insert a screw-
driver into the lever lower groove and turn it as shown in the
Spacer
illustration. Accelerator (10mm)
lever
Rod
CAUTION
Do not turn the lever too much.
Driver
ECLA005H
2. Insert the spacer (thickness: 10mm) between the rod and ad-
justing screw.
3. Remove the screwdriver.
CAUTION
When checking and adjusting to replace the injection
pump, stop the advance angle function not to result
in lack of power.
WAX TYPE COLD STARTING EQUIPMENT

This unit is adopted at low temperature to properly correct the fuel injection timing according to the engine coolant temperature.
Wax type cold starting equipment
KCLA006A
1-28 CHECKING POINT
STRUCTURE
1. Wax is sealed in the cold starting equipment, so the piston
rod is operated according to the engine coolant temperature.
Piston Wax
KCLA006B
2. The lever is rotated by the piston and the roller puller is oper- Timer
ated by pin(B) to control the injection timing in retard or Piston
Adjusting bolt
advance. The torsion spring pushes the piston to the injec-
tion timing advance angle direction.
Pin (A)
Idle control bolt
Lever (1)
Pin (B)
Outut side lever
Spring
Pump sie lever
KCLA006C
3. According to the engine coolant temperature except for the

injection timing, the rod connected in the accelerator lever
adjusts the engine idle speed.
Accelerator lever
Pin(A) Lever (1)
KCLA006D
CHECKING POINT 1-29
ADJUSTING INJECTION TIMING

Notch Timing indicator
CAUTION
Adjust the injection timing with the engine stopped.
1. Rotate the crankshaft to place the cylinder no.1 to the com-

pression dead point.
Crank pully
KCLA003G
2. Loosen the four union nuts in the injection pump side injec-
tion pipe and temporarily tighten them. Fix the distribution Distribution
holder
holder using a spanner not to be turned during loosening the
union nut. Nut
KCLA003H
3. Loosen the injection pump mounting nut and temporarily

tighten it.
Injection (4)
Bolt (2)
Nut (2)
KCLA003I
4. Remove the timing check plug from the injection pump.
Timing check plug

KCLA003J
1-30 CHECKING POINT
5. Before installing the special tool, check that the push rod is
jutted out about 10mm. Protrusion of the push rod is adjusted
by the inner nut. Push rod 09301-43000
09310 - 43000
Nut
10mm
10 mm
KCLA003K
6. Install the dial gauge by installing the special tool to the injec-
tion pump.
Dial gauge
KCLA003L
7. Align the crank pulley to 30° front of the cylinder no.1 com-
Approx
30˚30° 0
pression dead point.
8. Set the dial gauge to read '0'.
9. Slightly move the crank pulley notch left and right and check
that the pointer moves away from 0 position.
If the pointer is unstable, realign the notch position to 30°
front of the dead point
KCLA003M
10. Rotate the crankshaft to the right to place the pulley notch to
5°. 1 10.03
± 0.03
mmmm
Normal injection timing ATDC 5°
Recheck the dial gauge is within the standard.
Standard 1 0.03 mm
KCLA003N
CHECKING POINT 1-31
11. If the pointer of dial gauge is out of the standard values, move
the injection pump body left or right to correct and tighten the
injection pump mounting nut and bolt to the specified torque. Front View 10.03 mm or more
1±0.03
12. After adjusting, repeat the procedures (7) and (10) to check
that the adjustment is correct.
10.03 mm or less
1±0.03
KCLA003O
13.Detach the dial gauge and special tool and install the gasket
and plug.
14. Install the injection pipe nut.

Fix the spanner not to turn the distribution holder together.
15. Install a new gasket and tighten the plug to the specified Dial gauge
torque.
Plug
Tightening torque 2.3 ~ 3.7 kg m
KCLA003P
CHECKING AND ADJUSTING ENGINE IDLE Idle adjusting screw

SPEED
Speed up
Accelerator Lock nut
CAUTION
lever
Only use the idle speed adjusting screw.
1. Before checking and adjusting

• Engine coolant temperature: 80~90°C
2. Check the injection timing and valve clearance and adjust KCLA004A
them if required.
3. Install the idle speedometer.
4. Measure the engine idle rpm.
Standard 750 100 mm
5. If the measure the value is out of the standard, loosen the

lock nut and adjust it within the standard values by turning
the adjusting screw.
6. After adjusting, tighten the lock nut.

CHAPTER 2. ENGINE MECHANICAL SYSTEM
1. CYLINDER HEAD ASSEMBLY .............................................. 2- 1
2. TIMING SYSTEM ................................................................... 2- 14
3. FRONT CASE ........................................................................ 2- 25
4. MAIN MOVING SYSTEM ....................................................... 2- 31
5. CYLINDER BLOCK ............................................................... 2- 41

CYLINDER HEAD ASSEMBLY 2-1
1. CYLINDER HEAD ASSEMBLY

1) LOCKER ARM & CAM SHAFT
COMPONENTS
0.5 ~ 0.7kg·m
3
3.5 ~ 4.0kg·m
4 10
6
7
16
9
15
8 14
13
1.9 ~ 2.1kg·m
17
12
11
<Disassembly>
1. Breather hose 10. Adjust screw
2. Oil filler cap 11. Camshaft oil seal
3. Rocker cover 12. Camshaft bearing cap - Front
4. Rocker cover gasket 13. Camshaft bearing cap No.2
5. Packing 14. Camshaft bearing cap No.3
6. Rocker shaft 15. Camshaft bearing cap No.4
7. Rocker arm, Intake 16. Camshaft bearing cap - Rear
8. Rocker arm, Exhaust 17. Camshaft
9. Rocker shaft spring
KCMB800A
2-2 CYLINDER HEAD ASSEMBLY
INSPECTION
CAMSHAFT
1. Visually inspect the camshaft journals and replace them if
they are damaged and burned.
If the camshaft journals have burned, check the cylinder head
bearing for damage and the cylinder head oil passage for
Journal
clogging.
KCMB810A
2. Measure the camshaft diameter and bearing inner diameter

and if the oil clearance exceeds the limit value, replace the
camshaft, cylinder head or both.
Standard 0.05 ~ 0.08 mm
Limit 0.13 mm
KCMB100H
3. Check the cam surface for abnormal wear or damage and

replace it if required.
Measure the cam height (bigger diameter) and replace it if it
exceeds the limit.
Standard 37.05 mm
Limit 36.55 mm
ROCKER ARM
1. Check the contact surface with the cam and replace the rocker
arm if it damaged and burned.
2. Visually check the inside for damage or burn and replace it if

required.
3. Measure the inner and outer diameters and if the oil clear-
ance exceeds the limit, replace the rocker arm, shaft or both.
Standard 0.01 - 0.04 mm
Limit 0.08 mm
ROCKER SHAFT
1. Check the oil passage for clogging and clean it if required.
2. Check the rocker arm assembly for damage or burn and

ASSEMBLY
CAM SHAFT
1. Measure A and B, calculate the end play, and if the value
exceeds the limit, replace parts.
B - A = End play
Standard 0.01 - 0.04 mm

A B
Limit 0.08 mm ECLA019C
2. Install the camshaft with the dowel pin upward to the cylinder
head.
Dowel pin
Camshaft
KCMB820A
CAM SHAFT BEARING CAP

Assemble the camshaft bearing cap in sequence of the identifi-
cation number engraving on the upper surface of bearing cap.
CAM SHAFT OIL SEAL

09221--21000
09221 21000
1. Using the special tool, press-fit a new camshaft oil seal to the
front bearing cap portion. Cam shaft
2. Apply oil to the oil seal lip portion.
Oil seal
KCMB820B
ROCKER ARM (EXHAUST, INTAKE)

Take care not to make mistakes of the identification numbers.
ROCKER ARM SHAFT

1. Assemble the oil passage side shown in the illustration, fac-
ing it downward. Front
2. The shaft having one oil passage should be assembled in the

front.
One oil passage Two oil passages
KCMB820C
PACKING
Apply sealant to the marked portion in the illustration.
Specified sealant 3M P/No. 8660 or equivalent

Apply sealanat
KCMB820D
ADJUSTING VALVE CLEARANCE

Timing
1. Rotate the crankshaft clockwise to align the camshaft sprocket Camshaft mark
sprocket
with the timing mark.
KCMB820E
2. Adjust the valve clearance at the arrow position shown in the

illustration.
Ex. In. In. Ex.
KCMB280F
3. Loosen the adjusting screw mounting nut.
4. Adjust the valve clearance by turning the adjusting screw.
Standard (Cold engine)

Intake 0.15 mm
Exhaust 0.15 mm
5. Fix the adjusting screw not to turn using a screwdriver and

install the adjusting nut
ECLA019J
6. Rotate the crankshaft to one turn clockwise to place the cyl-

inder no.4 to the compression dead point.
7. Follow the procedures (2), (3) and (4) to adjust the valve
clearance.
Standard (Hot-engine)
Intake 0.25 mm
Exhaust 0.25 mm
8. After installing the engine assembly to the vehicle, inspect

the valve clearance with hot engine and adjust it if required.
Ex. In. Ex. In.
KCMB280G
2) CYLINDER HEAD & VALVE

COMPONENTS
4
5
10
6
1
7
Cold engine : 10.5~11.5 kg·m
11 Hot engine : 11.5~12.5 kg·m
12
13
14
8
[DISASSEMBLY]
1. Cylinder head bolt 10. Valve stem seal
2. Cylinder head 11. Intake valve guide
3. Cylinder head gasket 12. Exhaust valve
4. Valve spring retainer lock 13. Intake valve seat
5. Valve spring retainer 14. Exhaust valve
6. Valve spring
7. Spring seat
8. Intake valve
9. Exhaust valve
KCMB750A
DISASSEMBLY
CYLINDER HEAD BOLT
Using the special tool, Cylinder Head bolt Wrench (09221-32000),
loosen 18 Cylinder head bolts and remove them. Loosen the bolts
09221 - 32000
in the sequence shown and in two to three steps.
ECLA018B
6 14 16 8
1 10 18 12 4
5 13 15 7 3
2 9 17 11
KCDA052A
VALVE SPRING RETAINER LOCK

1. Using a valve spring compressor (09222 - 21000), compress 09222 - 21000
the spring and fit the retainer lock in position.
2. The valve spring, if compressed excessively, causes the bot-

tom end of retainer to be in contact with, and damages, the
stem seal.
ECLA018D
INSPECTION
CYLINDER HEAD
1. Before cleaning the cylinder head, check for water and oil
leaks, damage, or cracks.
2. Remove oil, scale, sealant, and carbon deposits completely.

After cleaning the oil passages, apply compressed air to en-
sure that the passages are not clogged.
3. If there is gas leak from the cylinder head gasket surface,

measure the surface flatness. If distortion exceeds the limit,
replace the cylinder head.
Standard value 0.05 mm less than
Limit L 0.2 mm
4. Visually check the camshaft bearing internal surfaces for dam-

age or seizure. If defects are evident, replace the bearing.
INTAKE VALVE, EXHAUST VALVE

1. If the valve stem develops wear (taper wear) or damaged,
replace. If there is a dent in the stem end face (the surface in
contact with the rocker arm adjust screw), replace.
Contact
Margin
KCMB770A
2. Check the valve face for contact. If the contact is not proper,
correct with a valve refacer. The contact pattern with the valve
seat must be even at the center of valve face.
3. Replace if the margin (valve head thickness) exceeds the limit.

Contact
Standard value 2.0 mm Margin
Limit 1.0 mm
KCMB770A
VALVE SPRING
1. Measure the free height of spring and replace if the limit is ˚
exceeded.
Standard value 49.1 mm

Free height
Limit 48.1 mm
2. Measure the squareness of the spring and, if the limit is

exceeded, replace.
KCMB100B
Standard value 2° less than
Limit 4°
VALVE GUIDE
Measure the valve guide to stem clearance and, if the measure-
ment exceeds the limit, replace the valve guide or valve, or both.
Exhaust 0.05 ~ 0.09 mm

Standard value
Intake 0.03 ~ 0.06 mm
Intake 0.10 mm
Limit
Exhaust 0.15 mm KCA9281D
RECONDITIONING VALVE SEAT

1. When reconditioning the valve seat, inspect clearance be-
tween the valve guide and valve and replace the valve guide
if required.
Special tool
2. Using the special tool or valve grinder, correct the seat width
and angle to the specified value. Cutter
VALVE SEAT CUTTER
Cutter angle Parts number 0.9 - 1.3 mm
45° 09221-43300 65˚
65° 09221-43400 65˚
30° 09221-43500
45˚
ECLA018E
3. Apply compound to the valve and seat.
VALVE SEAT REPLACEMENT PROCEDURE

0.5 - 1mm
1. Cut the valve seat to be replaced from the inside to thin the
wall thickness. Then, replace the valve seat.
2. Rebore the valve seat hole in cylinder head to the oversize Cutting portion
valve seat diameter.
0.5 - 1mm
Intake valve 0.30 O.S. 43.300 ~ 43.325mm
seat ring hole
diameter 0.60 O.S. 43.600 ~ 43.625mm
KCMB100D
Exhaust valve 0.30 O.S. 37.300 ~ 37.325mm
seat ring hole
diameter 0.60 O.S. 37.600 ~ 37.625mm
3. Before fitting the valve seat, either heat the cylinder head up
to approximately 250°C (482°F) or cool the valve seat in liq-
uid nitrogen to prevent the cylinder head bore from abrasion.
4. After installation, recondition the valve seat.

Height of valve seat
Over size I.D.
KCMB100E
VALVE GUIDE REPLACEMEMT PROCEDURE

1. Using the push rod of Valve Guide installer (09222 - 32200)
and apress, remove the valve guide forward cylinder block.
2. Rebore valve guide hole to the new oversize valve guide out-
side diameter.
0.05 O.S. 13.050 ~ 13.068 mm

0.25 O.S. 13.250 ~ 13.268 mm
0.50 O.S. 13.500 ~ 13.518 mm
CAUTION
Do not reassemble the same size of valve guide.
3. Using Valve Guide Installer (09222-32200), press-fit the valve

guide, working from the cylinder head top surface.
CAUTION
Take care not to change the exhaust and intake valve Push rod
guides because both lengths are not equal. 09222 - 32200
Valve guide
Cylinder head
KCMB770C
Vavle guide Valve guide

(Intake valve) (Exhaust valve)
71mm 74mm
KCMB770D
4. After installing valve guides, insert new valves in them to check

for sliding condition. Vavle guide Valve guide
(Intake valve) (Exhaust valve)
5. When replacing the valve guides, inspect valve contact and
correct the valve seat if required.
71mm 74mm
KCMB770E
INSTALLATION
VALVE STEM SEAL
1. Using Valve Stem Seal Installer (09222 - 32100), install the 09222 - 32100
valve stem seal into the valve guide.
CAUTION
• The valve stem seal must be not reused.
• The special tool must be used for the installation
of the valve stem seal. Improper installation could
result in oil consumption through valve guide.
Valve spring seat
KCMB780A
VALVE SPRING
Direct the valve spring end with identification color to the therocker Spring
Identification
arm.
Retainer
Stem seal
KCMB100F
VALVE SPRING RETAINER LOCK

Using a valve spring compressor (09222 - 21000), compress the 09222 - 21000
spring and fit the retainer lock in position.
CAUTION
The valve spring, if compressed excessively, causes the
bottom end of retainer to be in contact with, and damages,
the stem seal.
ECLA018D
CYLINDER HEDA GASKET

1. Clean contact surfaces between the cylinder head and cylin-
der block gasket.
2. Assemble the gasket facing upward the marking portion in

the illustration.
CYLINDER HEAD BOLT

1. Scrape off gasket adhered to cylinder head assembly.
2. Tighten in the numerical order indicated in the diagram in two

13 5 3 11
or three groups with special tool. 17 9 1 7 15
Specified torque 16
14 6 4 12
18 10 2 8
Limit 11.5 ~ 12.5 kg·m
Cold engine 10.5 ~ 11.5 kg·m KCMB780B

2-14 TIMING SYSTEM
2. TIMING SYSTEM
1) TIMING BELT
COMPONENTS
11 8
2.2 ~ 3.0kg·m
6.5 ~ 7.5kg·m
4 9
8 ~ 9kg·m
12
17 ~ 19kg·m 7
1 13 10
2 3 6
[DISASSEMBLY]
1. Crank shaft pully bolt 8. Timing belt tensioner
2. Washer 9. Tensioner speacer
3. Crank shaft pully 10. Timing belt
4. Timing belt upper cover 11. Camshaft sprocket
5. Timing belt lower cover 12. Injection pump sprocket
6. Acess cover 13. Crank shaft sprocket
7. Flange
KCMB850A
TIMING SYSTEM 2-15
REMOVAL
TIMING BELT
1. Remove the cooling fan, water pump, crankshaft pulley and
timing belt cover.
2. Turn the crankshaft to bring the piston in No. 1 cylinder to the

top dead center on the compression stroke.
3. Mark an arrow on the back of the timing belt and timing belt B
with a chalk to indicate the direction of rotation. This ensures
that the belt is installed in the same direction for reuse.
CAUTION
Stained belts with water or oils may be highly short
enedtheir life. So, the removed timing belt, sprocket
and tensioner should not be washed off, as well as
not be stained with oils. If the belts are seriously
stained, replace them.
ECLA020B
4. The piston in No. 1 cylinder is at the top dead center on the

compression stroke when all timing marks at the three places
are aligned as shown.
KCMB860A
5. Slightly loosen the two bolts securing the tensioner. Then,

slide the tensioner toward the water pump and tighten the Slide toward water pump
bolts temporarily to secure the tensioner in place.
KCMB860B
2-16 TIMING SYSTEM
CAMSHAFT SPROCKET
1. Loosen the bolt securing the camshaft sprocket and remove
the camshaft sprocket.
2. Remove the sprocket nut.
CAUTION
Use care not to give shock to the fuel injection pump
shaft, as it could result in defective fuel injection
KCMB860C
pump. Using Injection Pump Sprocket Puller (09314 -
43000) or suitable tool, remove the sprocket from in-
jection pump.
3. Remove the tensioner and tensioner spring.
INSPECTION
TIMING BELT
Carefully inspect the belt and replace it with a new one if there
are damages presented as below.
1. Hardened back surface of rubber

Back surface is glossy, Non-elastic and so hard that, when
your fingernail is pressed into it, no mark is produced.
ECA9200B
2. Cracked back surface of rubber

Crack Crack
3. Cracked or separating canvas
4. Badly worn out teeth (initial stage)

Separation
5. Badly worn out teeth (last stage) Crack
Crack
KCMB870A
TIMING SYSTEM 2-17
6. Side of belt cracked

Normal belt should have precisely cut side as if produced by
a sharp knife.
Separation
Rounded belt side
Abnormal wear
KCMB100J
7. Cracked tooth bottom

Initial state: Canvas worn (swollen canvas fiber, low quality of
Rubber exosed
rubber, discolored with white, and bad clearness)
Latter state: Canvas worn and rubber exposed (tooth width
narrowed)
Fiber exposed
8. Missing tooth
KCMB100K
TIMING BELT TENSIONER

1. Check it for smooth rotation and abnormal noise and replace
it if required.
2. Check it for clicking sound and rolling and replace it if required.
KCMB870B
TIMING BELT COVER

1. Check it for deformation and crack and replace it if required.
2. Check the seal for wear and damage and replace the timing
belt if required.
2-18 TIMING SYSTEM
INSTALLATION
Crank shaft
CRANKSHAFT SPROCKET
1. Mount the crankshaft sprocket to the crankshaft noting the
direction of the sprocket as well as the flange. Oil pump gear
drive shaft
2. Mount the camshaft sprocket and tighten the flange bolts to
specified torque. Sprocket
Sprocket “ B ”
3. Be careful of the flange installation direction. Flange
KCMB880A
TIMING BELT TENSIONER

1. Install the tensioner, tensioner spring and tensioner spacer.
2. The tensioner moved all the way to the water pump, tempo-
rarily tighten bolt.
CAUTION
When installing, face the short end of tensioner spring
toward the water pump.
KCMB870B
TIMING BELT Camshaft

sprocket Separation
1. Correctly line up timing marks on three sprockets.
2. While ensuring that the tension side of timing belt is not slack,
Injection
install belt onto the crankshaft sprocket, injection pump pump sprocket
sprocket, tensioner and camshaft sprocket, in that order.
Tensioner
CAUTION Separation
• When installing the belt onto the injection pump
sprocket, keep the sprocket in position, as it tends Crankshaft sprocket KD4B2010
to turn by itself at the timing mark alignment

position.
• If the belt is to be reused, make sure that the ar-
row mark made during disassembly faces to the
correct direction at reassembly.
TIMING SYSTEM 2-19
3. Check if all timing marks are aligned correctly.
Bolt A
Bolt B
KCMB870B
4. Back off tensioner bolt A, that have previously been secured

to the water pump side, one to two turns to give tension to the
Camshaft sprocket
belt using tensioner spring tension.
5. Confirm that the timing belt is correctly engaged with three

sprockets.
CAUTION Crank shaft

Turn crankshaft clockwise by the two teeth of the cam-
shaft sprocket and keep the position.
KCMB880C
6. Tighten bolt A.
Deflection
7. Tighten bolt B.
CAUTION
If the bolt B is tightened first, the tensioner should be
turned together, causing an undue tension to be ap-
plied to the timing belt.
8. Turn the crankshaft in the direction of backward rotation to

line up timing marks. KCMB880E
9. In this condition, ensure that the deflection when the center

of belt is pushed by the index finger.
Standard 4 ~ 5 mm
2-20 TIMING SYSTEM
FLANGE INSTALLATION
Notch for timing
adjustment
Note that bolt holes in the flange and those in the injection pump Sprocket
sprocket are offset positioned at one place. When assembling, Offset
position the jlange and sprocket as shown.
Flange
KCMB880F
TIMING SYSTEM 2-21
2) TIMING "B"
COMPONENTS
9
7
3.4 ~ 4.0kg·m
8 2 3 4 5
2.2 ~ 3.0kg·m
3.4 ~ 4.0kg·m
10
1
6
1. Flange
2. Gasket
3. Tensioner spacier
4. Tensioner spring B
5. Timing belt tensioner B
6. Timing belt B
7. Silent shaft sprocket-right
8. Silent shaft sprocket-left
9. Spacier
10. Crank shaft sprocket B
KCMB900A
2-22 TIMING SYSTEM
REMOVAL
TIMING BELT "B"
1. Remove the timing belt.
2. Using chalk or the like, put an arrow on the back of the timing
belt "B" to indicate the direction of drive.
ECLA021B
3. Slightly loosen the bolts and nuts securing the tensioner. Then,
slide the tensioner toward the water pump and tighten the
nuts to secure the tensioner in place temporarily.
4. Remove the timing belt "B".
5. Remove the crankshaft sprocket "B".
6. Remove the two silent shaft sprockets.
SILENT SHAFT SPROKCET(LEFT, RIGHT)

Screw driver [shaft dia. Wrench extension
When loosening the nut and bolt for two silent shaft sprockets, be 8 mm (0.31 in.) bar or similar size rod
sure to lock the silent shaft as shown.
CAUTION
Water, oil, or grease on the belt shortens its life
Slient shaft,
drastically. Use special care to ensure that the re- left
Silent shaft,
moved timing belt, sprockets, and tensioner are free right
from oil and grease.
Right side
Remove this plugh and insert a screwdriver

Remove cover and inseft bar
KCMB910A
TIMING SYSTEM 2-23
INSTALLATION Crank shaft
1. Mount the crankshaft sprocket "B"to the crankshaft, noting

the direction of the sprocket "B".
Oilpump gear
drive shaft
Sprocket “ B ”
KCMB920A
2. The spacer must be installed with its chamfered end facing

toward the silent shaft. If the spacer is installed in the wrong Spacier
direction, damage to oil seal will result. Silent shaft
Tapper
KCMB920B
TIMING BELT "B" TENSIONER Water pump

1. Install the tensioner spring and spacer, with the tensioner
moved all the way to the water pump.
Bolt
2. Tigh ten the nut. Tighten the bolt not fully put finger tight.
Nut
A
Spacier
Tensioner A-A
Gasket
Front lower
case
Tensioner spring “ B ”
KCMB920C
2-24 TIMING SYSTEM
TIMING BELT "B"

Timing mark
1. Line up timing marks on the crankshaft sprocket B, and right
Tensioner "B"
and left silent shaft sprockets.
Timing mark
2. With the timing belt B installed, ensure that its tension side is
not slack. Tension
Timing belt "B"
CAUTION
If the belt is to be reused, make sure that the arrow
mark made during disassembly faces to the correct Crank shaft sprocket "B"
KCMB920D
direction at reinstallation.
3. With the tension side of timing belt B kept tight by pushing

Timing mark
the slack side (indicated by A in illustration) with a finger,
make sure that the timing marks are properly aligned with Timing mark
each other.
Tension
Tension
KCMB920E
4. Back off tensioner B nut, that have previously been secured

to the water pump side, one to two turns to give tension to the
belt using tensioner spring tension.
5. First tighten the timing belt "B" tensioner mounting nut and
then the bolt.
Bolt
CAUTION Nut
If the bolt is tightened first, the tension B should be Tensioner
spring "B"
turned together, resulting in reduced timing belt B
tension. KCMB920F
6. Ensure that the deflection is 4 to 5 mm (0.0394 to 0.1969 in.)

Silent
when the belt is pushed by the index finger at the position
indicated by and arrow.
Belt deflection 4 ~ 5 mm Belt deflection
Crank shaft
sprocket "B"
KCMB920G
FRONT CASE 2-25
3. FRONT CASE
1) FRONT CASE, SLIENT SHAFT, OIL PAN
COMPONENTS
21
19
1.5 ~ 1.8kg·m
11 15
3.4 ~ 4kg·m 16
18 N
17
9
2.0 ~ 2.7kg·m 13 N
20
12
14
19
1.2 ~ 1.5kg·m 21
8N
2N
7
1.2 ~ 1.5kg·m
6
[DISASSEMBLY] 1
1. Oil drain plug 6 ~ 8kg·m
2. Oil drani plug gasket 0.6 ~ 0.8kg·m
3. Oil pan 3
4. Oil screen
5. Oil screen gasket
6. Front upper case
16. Silent shaft driven gear
7. Oil seal
17. Silent shaft driven gear
8. Front upper case gasket
18. Oil seal
9. Plug Cap
19. Silent shaft, right
10. O-ring
20. Silent shaft, left
11. Flange bolt
21. Bearing, rear
12. Flange lower case
13. Flange lower case gasket [Remarks]
14. Front oil seal Assembly is the reverse of disassembly.
15. Silent shaft gear cover Do not reuse N marking parts.
N
KCMB150A
2-26 FRONT CASE
REMOVAL
OIL PAN
Remove the oil pan by tapping the oil pan bottom edge or drain
plug with a soft hammer.
CAUTION
Do not insert a chisel or screwdriver between the oil
pan flange and cylinder block to remove the oil pan.
It may deform the oil pan flange surface. ECLA007H
FLANGE BOLT REMOVAL

Cylinder block right
1. Remove the plug on the right side of the cylinder block.
Plug
KCMB160A
2. Insert a screwdriver (cross slotted) into the plug hole not

to turn the silent shaft.
Driver
3. Remove the flange bolt.
Silent shaft right
KCMB160B
FRONT CASE 2-27
INSPECTION
SILENT SHAFT
1. The oil holes must be free from clogging.
2. Check journal for seizure, damage, and contact with the

bearing. If defects are evident, replace the silent shaft, bearing,
or front case assembly.
3. Check the silent shaft for oil clearance. If wear is excessive,

ECLA007K
replace the silent shaft bearing, silent shaft, or front case
assembly.
STANDARD VALUE
Front left 0.02 ~ 0.6 mm

Front right 0.02 ~ 0.05 mm
Rear 0.05 ~ 0.09 mm
FRONT UPPER CASE, FRONT LOWER CASE

Check them for damage and crack.
Replace them if required.
OIL PAN
Check the gasket surface for deformation and replace it if required.
REPLACEMENT
SILENT SHAFT
09212-43300
1. Use Bearing Installer Stopper (special tool) only for removal
and reinstallation of the right bearing.
ECLA008A
2-28 FRONT CASE
2. Using Bearing Installer Stopper and Silent Shaft Bearing Puller

(09212 - 43300, 09212 - 43100), remove two rear bearings 09212 - 43100 Bearing
from the cylinder block.
09212 - 43300
KCMB180B
3. Using Bearing Installer Stopper and Silent Shaft Bearing Puller

(09212 - 43300, 09212 - 43100), remove two rear bearings 09212 - 43200
from the cylinder block. Bearing
Apply
09212 - 43300 oil
KCMB180C
4. When press-fitting the right bearing, align the bearing oil hole
with the cylinder block oil hole. Bearing oil hole
Silent shaft bearing
Plug
Cylinder block
Oil hole
KCMB180D
INSTALLATION Oil seal

Socket
OIL SEAL
Install special tools in drive gear and apply to engine oil to drive
gear shaft.
KCMB190A
FRONT CASE 2-29
SILENT SHAFT GEAR

Silent shaft
1. Apply engine oil to the gear.
Mating
2. Align the mating marks on the silent shaft drive gear and driven marks
gear and assemble them to the front lower case
KCMB190B
Drive gear
Front lower case
09222 - 43200
Oil seal
KCMB190C
FRONT LOWER CASE

Front lower case
When tightening the bolts, be sure to secure the silent shaft in L = 55
position. L = 25
L = 75
L = 65 L = 25
L = 55 L = 65
L = bolt screw length (mm)
KCMB190D
FRONT OIL SEAL Oil seal Front lower case

1. Install the special tool guide to the crankshaft and apply en- Crank shaft
gine oil to the outer surrounding.
Oil pump
2. Using the special tool, assemble the front oil seal to the case. driver shaft
09214 - 32000
(Apply oil to outer
surrounding) 09214 - 32100
KCMB190E
2-30 FRONT CASE
FLANGE BOLT
1. Insert a screwdriver (cross slotted) into the plug hole not to
turn the silent shaft(right).
2. Assemble the flange bolt and tighten it to the specified torque.
KCMB190F
KCMB190G
OIL PAN
1. Remove the sealant attached in the cylinder block and oil
pan gasket surface.
2. Apply sealant to the oil pan flange to the thickness of 4mm.
3. After applying sealant, assemble the oil pan and tighten the
bolt to the specified torque in 15 minutes.
Tightening torque 0.6 ~ 0.8 kg·m

MAIN MOVING SYSTEM 2-31
4. MAIN MOVING SYSTEM

1) CRANK SHAFT & FLY WHEEL
COMPONENT
13 ~ 14 kg·m
5 1
8
9
7
10 6
14
13
12
11
7.5 ~ 8.5 kg·m
1. Fly wheel assembly 8. Bearing cap

2. Rar plate 9. Crank shaft bearing-Lower
3. Bell housing cover 10. Crank shaft
4. Oil sela case 11. Crank shaft bearing-Upper
5. Gasket [Remarks]
6. Oil separator (1) Assembly is the reverse of disassembly
7. Rear oil seal (2) Do not reuse N marking parts.
KCMB200A
2-32 MAIN MOVING SYSTEM
INSPECTION
CRANKSHAFT
1. Visually inspect the journals and pins for damage and replace
them if required.
2. Measure the journal O.D. and main bearing I.D. and if the
clear ance exceeds the limit, replace the main bearing (and
crank shaft if required).
Or, grind the crankshaft to undersize and replace it with the ECLA009B
undersize main bearing.
Limit 0.01 mm A
1 2
B
KCMB210A
3. When grinding the crankshaft to undersize, ensure correct

2.5 mm R
fillet radius dimensions in journals and pins.
2.5 mm R
2.5 mm R
KCMB210B
CRANKSHAFT OIL CLEARANCE (PLASTIGAGE

Plastic gauge
METHOD)
1. Wipe crankshaft O.D. and bearing I.D. clean of oil.
2. Install the crankshaft.
3. Put a strip of Plastigage lengthwise in the center of the journal.
KCMB210C
4. Replace the main bearing cap carefully and tighten bolts to

specification.
5. Remove bolts and carefully remove the main bearing cap.
6. Using the scale printed on the bag of plastigage, measure

the amount the Plastigage has been flattened (the widest
point).
ECLA009F
CRANKSHAFT FRONT AND REAR OIL SEALS

1. Wear and damage in oil seal lips.
2. Deteriorated or hardened rubber.
3. Cracks or damage on oil seal case.
RING GEAR
1. If the ring gear teeth are worn, damaged, or broken, replace Fly wheel
Ring gear
the ring gear.
2. If the teeth are damaged or broken, check the starting motor

pinion.
3. To remove the ring gear for replacement, tap its outer rim one
place after another. Heating the gear makes it impossible to
remove. To install the ring gear onto the flywheel, heat it up to
KCMB210D
260-280°C (500-536°C) : it is a shrink fit in the flywheel.
FLYWHEEL
1. Visually inspect the flywheel clutch disc surface for wear and
damage and replace it if required
2. If the clutch disc surface rolling exceeds the limit, replace it.
Limit 0.13 mm
DRIVE PLATE (AUTOMATIC TRANSAXLE)

Check the drive plate for deformation, damage and crack and
INSTALLATION Without oil hole With oil hole
1. Install the upper crankshaft bearing to the cylinder block.

There is oil hole in the upper crankshaft bearing. Upper bearing
Lower bearing (No. 1. 2. 4. 5)
(No. 1.2.4.5)
2. Install the lower crankshaft bearings to each bearing cap and (No.(No.
1. 2. 4. 5)
1.2.4.5) Without oil hole
apply engine oil to the bearing surface.
Upper & lower

bearning(middle)
KCMB220A
BEARING GAP
Main bearing cap direction
1. Install the main bearing to the cylinder block. Ensure the cor-
rect cap number and arrow mark direction.
Arrow
(Display engine forward)
Engine direction
No.
Cap No.
KCMB220B
2. Check to ensure that the crankshaft turns smoothly and there

is an adequate end play.
Limit 0.25 mm
ECLA009J
OIL SEAL CASE

Using special tool, press-fit a new crankshaft rear oil seal into the
oil seal case.
09231 - 32000
KCMB210C
OIL SEPARATOR
Push oil separator into the oil seal case. Make sure that the oil
hole in the separator comes at the bottom (indicated by an arrow
in illustration.)
Oil hole
KCMB220C
2) PISTON
COMPONENTS
6
7
9
8
11
10
5
13
12
[DISASSEMBLY]
1. Nut
2. Connect rod cap
3. Connect rod bearing
4. Piston & connecting rod assembly
3
5. Connect rod bearing
6. Bolt
7. Piston ring No.1
8. Piston ring No.2 2
9. Oil ring
10. Piston
11. Snapring 1
12. Piston rod 4.5 ~ 4.8 kg·m
13. Connect rod [Remark]
14. Bushing (1) Assembly is the reverse of disassembly
KCMB250A
INSPECTION
PISTON
1. Check each piston for scuffing, scoring, wear and other
defects. Replace any piston that is defective.
2. Check that the piston pin fits in the piston pin hole.
CAUTION
Replace the piston and piston pin as an assembly.
3. Replace any piston and pin assembly that is defective.
4. The piston pin must be smoothly pressed by hand into the

pin hole (at room temperature).
PISTON RING
1. Check each piston ring for breakage, damage and abnormal
wear. Replace the defective rings.
2. When the piston requires replacement, its ring should also

be replaced.
Item TC NA
No.1 0.056 ~ 0.076 0.03 ~ 0.07
Standard No.2 0.046 ~ 0.066 0.08 ~ 0.12
OIL 0.02 ~ 0.065 0.02 ~ 0.065 ECLA010B
No.1 0.15
imit No.2 0.15
OIL 0.1
3. Measure the clearance between piston ring and ring home.

Thickness
Piston gauge
ECLA010C
4. Place a piston ring in the cylinder bore and set it square by

pushing it down with piston.
Item TC NA
No.1 0.30 ~ 0.50 0.25 ~ 0.40
Standard No.2 0.41 ~ 0.54 0.45 ~ 0.60
OIL 0.25 ~ 0.45 0.20 ~ 0.40
Limit 0.8 Piston Eng gap

ring
KCMB260A
CONNECTING ROD BEARING

1. Check the bearing surfaces for uneven contact pattern,
streaks, scratches, and seizure. If defects are evident, replace.
If the surfaces are seriously nicked and seized, check also
the crankshaft. If the crankshaft is also damaged, replace the
crankshaft or grind to undersize for reuse.
ECLA010E
2. Measure the connecting rod bearing I.D. and crankshaft pin

O.D. If the clearance (oil clearance) exceeds the limit, replace
the bearing and, if necessary, the crankshaft. Or, grind the
crankshaft to an undersize and, at the same time, replace the
bearing with an undersize.
Limit 0.1 mm
ECLA010F
CONNECTING ROD BUSHING Pull out
1. Pull out the bushing using the special tool.
09214 - 43000
Pull out
ECLA010G
2.. Press-fit the bushing using the special tool.

At this time, align the busing with connecting rod small end
oil hole.
09214 - 43000
Apply oil
Bushing
Align to the Chamfer side

oil hole
ECLA010H
3. Adjust the busing inner diameter within the standard values.
Standard 29.015 ~ 29.025 mm
ECLA010I
CAUTION
1. Insert the piston pin, following the front mark.
Front mark
Front mark
KCMB260B
2. Install the snap ring in the following direction.
ECLA010K
INSTALLATION
No. 1
PISTON RING INSTALLATION
No. 2
1. Install the oil ring expander and oil ring to the piston.
Oil
2. Then, install No.2 piston ring and No.1 piston ring, in that
order. Make sure that the ring side, on which manufacturer
and size marks are stamped, faces to the piston crown.
KCMB270B
PISTON & CONNECTING ROD ASSEMBLY

Upper side rail
No. 1
1. Apply engine oil to the piston surface, piston ring and oil ring.
2. Adjust gap between the piston ring and oil ring as shown in
the illustration. Piston pin
No. 2 Lower side rail
KMBC270B
3. Insert the piston and connecting rod assembly from above

the top of cylinder. Ensure that the front mark on piston crown
and that (ID mark) on the connecting rod face toward the front
of engine (to the crank pulley side).
4. Clamp firm the piston rings with the ring band and install the
piston assembly into cylinder. Do not strike it hard into the
piston, as broken piston ring or damaged crank pin could
result.
ECLA010N
5. When assembling, align the bearing cap with the connecting

rod.
If parts are new ones, align notches in the same direction.
6. Make sure the clearance of connecting rod big end side.
Limit 0.4 mm
ECLA010O
CYLINDER BLOCK 2-41
5. CYLINDER BLOCK
1) CYLINDER BLOCK
COMPONENTS
5
4 ~ 5 kg·m
N 2 1
6 5 ~ 6 kg·m 4 0.5 ~ 0.7 kg·m
[DISASSEMBLY]
1. Cover
2. Packing
3. Engine bracket, right
4. Engine bracket, left [Remarks]
5. Cylinder sleeve (1) Assembly is the reverse of disassembly
6. Cylinder block (2) Do not reuse N marking parts
KCMB030A
2-42 CYLINDER BLOCK
INSPECTION
CAUTION
• Before inspection and repair, clean parts to re-
move dirt, oil, carbon, deposits, and scale.
• Before cleaning the cylinder block, be sure to
check for evidences of water leaks and damage.
• Romove contaminants from oil holes with com-
pressed air and, at the same time, make sure that
they are not blocked.
CYLINDER BLOCK C D E
A F
1. Check for scratches, rust, and corrosion. Use also a flaw -
detecting agent for the check. If defects are evident, correct B G
or replace.
2. Using a straightedge and thickness gauge, check the cylin-

der block top surface for flatness. Lay the straightedge
longways and crossways as indicated by A, B,... in illustration.
If flatness is not within the limit, replace the cylinder block. At
ECLA007B
measurement, ensure that the cylinder block top surface is
free from any traces of gasket material.
Standard 0.05 mm
Limit 0.1 mm
3. Check cylinder wall for scratches and seizure. If defects are

evident, correct (to oversize) or replace.
4. Using cylinder gauge, measure the cylinder bore. If it wears

out excessively, bore the cylinder to oversize and replace
the piston and piston rings. Measurement points are as
shown.

Middle
Bottom
KCMB040A
CYLINDER BLOCK 2-43
BORING OF CYLINDER
1. Using the maximum cylinder bore as a basis, determine the
oversize piston to be used.
There are four oversize pistons available :
Size Identification mark
0.25 mm(0.01 in.) O.S. 0.25

0.50 mm(0.02 in.) O.S. 0.50
0.75 mm(0.03 in.) O.S. 0.75
1.00 mm(0.04 in.) O.S. 1.00
CAUTION
Sizes are marked on the pistons.
2. Based on the piston O.D. measured, calculate the boring

dimension.
• Boring dimension
Piston O.D. + 0.04 to 0.06 mm
(piston to cylinder clearance) - 0.02 mm (0.0008 in.)
(honing margin).
Piston O.D.
4. Bore cylinders to obtain the calculated boring dimension.

KCMB040B
CAUTION
To prevent thermal distortion due to temperature rise
during boring operation, bore cylinders in the se-
quence of No. 2, 4, 1 and 3.
5. The cylinders must be honed to finish dimension.
6. Check clearance between piston and cylinder.
TC NA
Clearance
0.02 ~ 0.08 mm 0.03 ~ 0.05 mm
CAUTION
1. When boring cylinders, finish all of four cylin
ders to the same oversize.
2. Don't bore only one cylinder to oversize.
2-44 CYLINDER BLOCK
2) REPLACING CYLINER SLEEVE

REMOVAL
Face the rounded
side toward the block
1. Fix the cylinder block with a boring machine before centering.
Centering should be done in the lower part of the cylinder
sleeve where has little abnormal wear. Thin cylinder
sleeve
2. Bore the sleeve until the thickness is 0.5mm.
KD4B2001
3. Insert the processed screwdriver as shown in the illustration

between the cylinder sleeve and cylinder block and remove
the cylinder sleeve by tapping on the screwdriver slightly. Be
careful not to damage the cylinder block wall.
Attach a round piece
to the screwdriver
KD4B2002
INSPECTION
1. After removing the cylinder sleeve, inspect the cylinder block
sleeve hole surface.
2. If there are damages, scuffing, abnormal wear and other

defects, bore the cylinder block sleeve hole to oversize.
3. Measure the cylinder sleeve O.D. and cylinder block sleeve

Y direction
hole I.D. with a gauge placed as shown in the illustration.
Measure D1, D2 and D3 in the directions of X and Y and if the Xdirection
average value is below 0.12mm, bore the sleeve hole to 0.
5mm oversize and press-fit the oversized sleeve into the sleeve
hole. 12mm D1
Middle D2
CAUTION
Bottom D3
Be sure when boring the cylinder, all sleeves should
KD4B2003
be removed from all cylinders not to make mistakes
during rounding.
CYLINDER BLOCK 2-45
PRESS-FIT Hydraulic press
1. Without boring cylinder block sleeve hole Cylinder sleeve
1) Apply press oil to the cylinder block sleeve hole surface

and sleeve outer surface.
2) Put a flat rounded plate on the sleeve top end and press-
fit it with a hydraulic press.
Press-fit load 2200kg or more

KD4B2004
3) Press-fit the sleeve until the sleeve top end surface is

flush with the block top surface.
Press-fit it toward the chamfer as shown in the illustration.
Upper part
Lower part
KD4B2005
4) To prevent the cylinder sleeve and cylinder block top sur- No slice
faces from roughness and bump, cut the cylinder block
top surface.
Difference between them should be '0' as possible. (The
limit: 0.2mm) Cylinder
sleeve Cylinder
block
KD4B2006
5) Chamfer the cylinder sleeve top end as shown in the

illustration. 1mm Cylinder sleeve
30
KD4B2007
2-46 CYLINDER BLOCK
6) Cylinder sleeve I.D. is processed with 90.08~90.10mm,

after press-fitting the sleeve, hone the bore to be within
the standard value.
Cylinder bore 91.10~91.13mm
Honing surface formation 2~4
Honing rendering angle (Cross-hatch) 15~25°
Cylinder bore perpendicularity 0.05mm
2. Boring cylinder sleeve hole
1. Prepare a 0.5mm oversized cylinder sleeve.
2. Hone the cylinder block sleeve hole to 94.025~94.050mm.
3. Press-fit the cylinder sleeve and render the bore.

For press-fit and process procedures, refer to "Without
boring block sleeve hole".
INSPECTION AFTER ASSEMBLY

Protrusion Piston
Cylinder block
1. After assembling the crankshaft and piston, inspect protru-
sion of the piston.
If the protrusion is out of the limit, replace the piston inserted
into thin one to be the protrusion within the limit.
2. After procedure 1, if the protrusion is not within the limit, re-

place the cylinder block.
KD4B2008
Limit 1.1 mm
CHAPTER 3. LUBRICATION
1. OIL FILTER ............................................................................ 3- 1
2. OIL PAN ................................................................................. 3- 5
3. OIL PUMP .............................................................................. 3- 7

OIL FILTER 3-1
1. OIL FILTER
COMPONENTS
1 4
3.0 ~ 4.5 kg·m
1.2 ~ 1.5 kg·m
2
5.0 ~ 6.0 kg·m
3
0.8 ~ 1.2 kg·m
[DISASSEMBLY] 10
1. Oil filter
2. Oil cooler by - pass valve 9
3. Oil pressure switch
4. Joint 8
5. Tapper plug
7
6. Oil filter bracket
3.0 ~ 3.5 kg·m
7. Check valve
8. Gasket
9. Oil jet
10. Gasket
[Remarks]
(1) Assembly is the reverse of disassembly
(2) Do not reuse N marking parts
KCUB050A
3-2 OIL FILTER
REMOVAL
OIL PRESSURE SWITCH 09260 - 32000
To remove the oil pressure switch, use Oil Pressure Switch Wrench
(09260 - 32000).
CAUTION
During removal, use care to prevent damage to the
sealant applied to threads.
ECLA013B
INSPECTION
OIL FILTER BRACKET
1. The oil filter mounting surface must be free from damage.
2. Check for cracks and oil leaks.
OIL PRESSURE SWITCH

1. Connect a tester (Ω range) between the terminal and the body
of the switch to check for continuity. The switch is normal if
there is continuity. If there is no continuity, replace the switch.
ECLA013C
2. Insert a thin rod in the oil hole of the switch and push it in
lightly. The switch is normal if no continuity is detected (infinite
resistance on the tester). If there is continuity, replace the
Thin rod
switch.
KCDA052A
OIL FILTER 3-3
3. Apply a 0.5 kg/cm2 pressure to the oil hole. The switch is nor-
mal if there is no continuity. Also check for air leaks. If any air
leaks are detected, the cause may be a broken diaphragm.
Replace the switch if it leaks.
OIL JET, CHECK VALVE

1. Check the oil jet and check valve for clogging. Engine oil
2. Check the oil jet for damage and deformation.
Oil jet
Check valve
assembly KCMB520A
OIL COOLER BYPASS VALVE

1. Ensure that the dimension L measures the standard value L
under normal temperature and humidity.
Dimension L 34.5mm
Valve
2. The dimension must be the standard value when measured
after the valve has been dipped in 100°C. KCMB520A
Dimension L 40mm
3-4 OIL FILTER
INSTALLATION
OIL JET
No.1.3
No.1, 3 No.2,
No.2.44
There are two types of oil jets installed: one for No. 1 and 3, and Cylinder Cylinder
the other for No. 2 and 4. Make sure that the correct one is in-
stalled with correct direction as shown.
Oil jet Oil jet
(No.1, 3) (No.2, 4)
Cylinder block
knock pin
Check valve
Oil jet
KCMB530A
OIL JET SWITCH

1. Before installation, apply sealant to the switch threads.
CAUTION
• The sealant must not get into the thread top
surface.
• Use care not to torque excessively.
OIL FAN 3-5
2. OIL PAN
COMPONENTS
3.5~4.5 kg ·m
1 0.6~0.8 kg ·m
1. µ å
1. Drain plug
2. Oil pan
3. Oil screen
4. Gasket
KD4B3001
3-6 OIL FAN
REMOVAL
OIL FAN
When the oil pan is stuck with the gasket, remove it by tapping
the drain plug downward with a plastic hammer or equivalent.
KD4B3002
INSTALLATION
OIL FAN
1. Remove the gaskets attached in the oil pan and cylinder block
using a scrapper, wire brush, etc.
KD4B3003
2. Cut the nozzle attached to the liquefied gasket as shown in

the illustration. The liquefied gasket comes out with 4mm
diameter.
MZ 100080
Semi-dry sealant
THREEBOND TB1212
Cutting part
KD4B3004
3. Squeeze the liquefied gasket from the tube and apply it to the
oil pan as shown in the illustration.
Apply 4mm
sealant Diameter
Bolt hole
KD4B3005
OIL PUMP 3-7
3. OIL PUMP
COMPONENTS
7
4
3.0 ~ 4.5 kg·m
0.9 ~ 1.4 kg·m
2
3
1. Oil pump cover

2. Oil pump outer gear
3. Oil pump inner gear
4. Plug
5. Gasket
6. Relief plunger
7. Relief spring
8. Oil pump case
[Remark]
Do not reuse N marking parts.
KCMB550A
3-8 OIL PUMP
DISASSEMBLY
Inner rotor
Before removing the oil pump outer and inner gears, mark the
outer gear to make sure that it goes back to the position with Marking
correct direction.
Outer rotor
KCMB560A
INSPECTION
OIL PUMP ROTOR
1. Install the outer and inner gear into the front case and make
sure that they turn smoothly with no excessive play between
them.
2. Check the side clearance (the front case and oil pump cover
surface).

Limit 0.15 mm
3. Measure the body clearance and if the measure value ex

ceeds the limit, replace the gear or case.
Item Standard Limit

Inner rotor 0.22 ~ 0.35 mm 0.5 mm
Outer rotor 0.12 ~ 0.22 mm 0.4 mm
4. Check the oil pump cover rotor contact surface for wear and if
there is bump, replace the cover. (If the individual part is not
available, replace it as an oil pump case assembly).
OIL PUMP 3-9
INSTALLATION
OIL PUMP INNER ROTOR/OIL PUMP OUTER ROTOR
1. Apply engine oil to all rotor surfaces.
2. Install the gear in the same direction as markings represented

during disassembly. Inner rotor
Marking
Outer rotor
KCMB560A
3. When air pressure of 0.5kg/cm² is applied to the oil hole, if

there is no continuity, it is normal.
If air leakage is detected, replace the switch because the dia
phragm may be damaged.
OIL JET, CHECK BELT

1. Check the oil jet and check valve for clogging.
2. Check the oil jet nozzles for damage or deformation.

3-10 OIL PUMP
OIL COOLER BYPASS VALVE

L
1. Standard value of 'L' at room temperature.
Standard 34.5mm
2. Limit value of 'L' after coming out from oil of 100°C.

KCMB580B
Limit 40mm not less than

CHAPTER 4. COOLING SYSTEM
1. WATER PUMP & WATER PIPE ............................................ 4- 1
2. RADIATOR FAN MOTOR ...................................................... 4- 4
3. THERMOSTAT ...................................................................... 4- 8
4. RADIATOR ............................................................................ 4- 10
WATER PUMP & WATER PIPE 4-1
1. WATER PUMP AND WATER PIPE

COMPONENTS
10
11 9
1.2 ~ 1.5 kg·m
3.0 ~ 4.0 kg·m
14
2.0 ~ 2.5 kg·m

6 7 8
12
13
1.0 ~ 1.3 kg·m
1.2 ~ 1.5 kg·m
1.0 ~ 1.2 kg·m

[DISASSEMBLY]
1. Drive belt (V belt)
2. Cooling fan
3. Fan clutch
4. Water pump pully
(Power steering pump pully adhere)
5. Water pump pully
6. Water inlet fitting
7. water inlet fitting gasket
8. Thermostat
9. Coolant temperature gauge unit
10. Water inlet pipe
11. O-ring
12. Water pump [Remarks]
13. Water pump gasket (1) Assembly is the reverse of disassembly
14. Thermostat assembly (2) Do not reuse N marking parts
KCMB300A
4-2 WATER PUMP & WATER PIPE
INSTALLATION
DRIVER BELT
Inspect the following items and replace them if required.
1. Loose belt
2. Damage, crack, and wear
WATER PUMP & HOSE

1. Water pipe for crack, damage and clogging
2. Water hose for crack, damage and clogging
WATER PUMP
Check each part for cracks, damage or wear, and replace the
water pump assembly if necessary.
1. Coolant leaks
2. Coolant leaks from A
3. Water pump body for damage and crack A
4. Impeller for damage and crack

ECLA011B
5. Bearing for damage

WATER PUMP & WATER PIPE 4-3
ASSEMBLY
WATER PUMP
1. Clean the gasket contact surfaces inserting between the wa- d
ter pump and cylinder block.
1
2. Bolt sizes are as below. Indication for L(Length)
L
hardness category
Hardness
No category dx1 Torque
1 4T 4T 1.2~1.5 kg·m 2
3
2 4T 4T 1.2~1.5 kg·m
3 7T 7T 2.0~2.7 kg·m
2 2 1
KCUB040A
WATER PIPE & O-RING

O-ring
1. Fit water pipe O-ring in the groove provided at water pipe
end, wet the periphery of water pipe O-ring and insert water
pipe.
CAUTION
Do not apply oil and grease to water pipe O-ring.
KCMB320B
4-4 RADIATOR PAN MOTOR
2. RADIATOR PAN MOTOR

COMPONENTS
0.3 ~ 0.7 kg·m 1.0 ~ 1.2 kg·m 3
1.0 ~ 1.2 kg·m

1 0.3 ~ 0.7 kg·m 2
[DISASSEMBLY]
1. Radiator upper shroud
2. Cooling fan
3. Cooling fan clutch
[Remark]
(1) Assembly is the reverse of disassembly
KCMB420A
RADIATOR PAN MOTOR 4-5
INSPECTION
COOLING FAN
1. Check the blades for damage and cracks.
2. If any portion of fan is damaged or cracked, replacecooling

fan.
FAN CLUTCH
1. Check the case joint and seal for oil leakage from the pan
clutch.
2. Oil leakage may cause overheating the engine resulting from

Bimetal
the pan speed decrease.
3. Check the bimetal strip for damage
KCMB430A
4-6 RADIATOR PAN MOTOR
COMPONENTS
2
(1.0~1.2 kg·m)
1
(1.0~1.4 kg·m)
[DISASSEMBLY]
1. Whter temperature gauge unit
2. Thermo switch (113°C)
(For A/C equipped vehicle)
KCMB450A
RADIATOR PAN MOTOR 4-7
INSPECTION
WATER TEMPERATURE GAUGE UNIT
1. Put the sensor in water and increase the water temperature
measure the resistance.
ECLA012E
2. If the measurement radically deviates from specification,

replace.
3. Measure the resistance across terminal (A) and body for wa- Terminal (A)
Terminal (B)
ter temperature gauge element and across terminal (B) and
body for glow control element.
Standard
Terminal (A) 0.4Ω / 70°C

KCMB460A
(For coolant temp) 23.8Ω / 115°C
Terminal (B) 24.8Ω / -20°C
(For preheat plug) 3.25Ω / 20°C
THERMO SWITCH (FOR A/CON)

1. After inserting the coolant temperature switch into oil, heat
the oil.
2. Check that the coolant temperature switch is turned OFF when

the oil temperature reaches the standard.
Standard
Coolant temperature at A 113 3°C

ECLA012G
Coolant temperature at B 106°C
CAUTION
Only engine oil is available and stir the oil during
heating. Do not overheat.
4-8 THERMOSTAT
3. THERMOSTAT
COMPONENTS
2
3
N6
4
4 1 7
N8 9
12
7 9 10 N 11 12
1.1 kg·m
1.2~1.5 kg·m
2.4 kg·m N5
1.2~1.5 kg·m
1.2~1.5 kg·m
2.4 kg·m 1.2~1.5 kg·m
[THERMOSTAT DISASSEMBLY] [WATER PUMP DISASSEMBLY]

1. Radiator lower hose 1. Radiator lower hose
7. Water inlet fitting 2. Power steering oil hose
8. Gasket 3. Power steering oil pump bracket
9. Themostat 4. Water pump & thermostat
5. Water pump gasket
6. O-ring
10. Thermostat housing
11. Thermostat housing gasket
12. Water pump
KCUB040C
THERMOSTAT 4-9
INSPECTION
1. Check that valve closes tightly at room temperature.
2. Check for defects or damage.
3. Immerse thermostat in container of water.

Water temperature
gauge
82 2°C
Opening valve temperature
76.5 2°C
KCMB310A
ASSEMBLY
˚
Assemble the thermostat in the direction shown in the illustration.
Thermostat Thermostat
brush housing
Thermostat
KCUB040E
4-10 RADIATOR
4. RADIATOR
COMPONENTS
1
5
0.8 ~ 1.1 kg·m
7
6
0.3 ~ 0.7 kg·m
3 4
9 2
0.8 ~ 1.1 kg·m

0.8 ~ 1.1 kg·m
[DISASSEMBLY]
1. Radiator cap 7. Radiator upper shroud
2. Drain plug 8. Radiator lower shroud
3. Over flow tube 9. Radiator
4. Reserve tank [Remark]
5. Radiator upper hose
6. Radiator lower hose (1) Installation is the reverse of removal.
KCMB400A
RADIATOR 4-11
INSPECTION
1. Check between the radiator pins for foreign material.
2. Check the radiator pins for bending or damage.
3. Check the radiator for contamination, damage or rust.
4. Check the radiator hose for crack, damage or deformation.
5. Check the reservoir tank for damage.
6. Check the radiator cap spring for damage.
7. Check the radiator cap packing for damage or crack.

CHAPTER 5. INTAKE AND EXHAUST SYSTEM
1. INTAKE AND EXHAUST MANIFOLD ................................... 5- 1
2. TURBO CHARGER (TC)....................................................... 5- 3
3. AIR CLEANER ...................................................................... 5- 8

INTAKE AND EXHAUST MANIFOLD 5-1
1. INTAKE AND EXHAUST MANIFOLD

COMPONENTS
2 6.0 kg·m
6.0 kg·m
4
6
6.0 kg·m
1. Exhaust fitting
2. Gasket
3. Oil return pipe
4. Oil return pipe gasket
5. Exhaust manifold
6. Turbo charger gasket
7. Turbo charger assembly
KCMB600A
5-2 INTAKE AND EXHAUST MANIFOLD
ASSEMBLY
TURBO CHARGER ASSEMBLY
Remove the heat protector.
CAUTION
Be careful of foreign material not to come in the oil
passage during cleaning.
ECLA015C
EYE BOLT
Before installing the oil pipe eyebolt (turbocharger upper part), fill
the turbocharger with clean engine oil. After full filling, check that
the turbine and compressor wheel are rotating smoothly.
ECLA015D
TURBO CHARGER [TC] 5-3
2. TURBO CHARGER (TC)

COMPONENTS [D4BF]
4 5 2
8 7 6
3
0.4 ~ 0.5 kg·m
2.9 ~ 3.6 ft.lbs.
[DISASSEMBLY]
1. Hose clip
2. Hose
3. Coupling
4. Turbine housing
5. Snap ring
6. Compressor cover
7. O-ring
8. Cartridge assembly
KCUB060A
5-4 TURBO CHARGER [TC]
DISASSEMBLY
TURBINE HOUSING
Before removal, make the mating mark on compressor cover bear-
ing housing and turbine housing. Mating mark
CAUTION
Be sure not to damage the compressor and turbine
wheel blade.
KCMB660A
SNAP RING
Remove the snap ring using snap ring filler.
Snap ring
KCLA016C
CARTRIDGE ASSEMBLY
Remover by tapping the compressor cover of cartridge assembly
with plastic hammer.
NOTE
O-ring installed around the cartridge assembly may Cartridge
cause tight installation sometimes. assembly
CAUTION
KCMB660C
• Use a heavy duty carbon solvent to loosen the
carbon from the parts.
• Do not use caustic solutions, wire brushes, or wire
wheels to remove carbon deposits from any turbo
charger part.
INSPECTION
Contacting surface
TURBINE HOUSING
1. Check the inner housing contacting turbine wheel for crack,
pitching and other damages caused by overheat.
KCMB670A
2. Make sure that the waste gate valve lever operates freely by
hands.
COMPRESSOR COVER
Make sure there are no damages on the inner housing surface
contacting compressor wheel.
C ARTRIDGE ASSEMBLY
Compressor Oil passage Turbine wheel
1. Turbine wheel and shaft assemblies with cracks in the blades wheel
or broken blades can not be used again. If the blades are
slightly bent, it can be used again but severely bent blades
can not be reused.
2. Check if there are foreign materials disturbing the oil flow in

the oil passage of cartridge assembly.
KCMB670B
OIL PIPE AND OIL RETURN PIPE

Check the oil pipe and oil return pipe for clogging and deformation.
Repair or replace them if required.
5-6 TURBO CHARGER [TC]
WASTE GATE INSPECTION

Check the waste gate rod operation under the pressure below.
Pressure
TCI engine Approx. 0.80kg/cm2
ECLA016J
ASSEMBLY
O-RING ASSEMBLY
Apply engine oil to the new O-ring thinly and assemble the car-
tridge assembly.
O-ring
CAUTION
Take care not to damage the O-ring.
KCMB670C
COMPRESSOR COVER/CARTRIGE ASSEMBLY
1. Install the cartridge assembly to the compressor cover with

them mating as marked when disassembling.
2. When replacing it with a new one, install it as shown in the

left illustration. Mating mark
CAUTION
When installing the cartridge assembly to the com-
pressor cover, take care not to damage the compres- KCMB670D
sor wheel blade.
SNAP RING
Snap ring Chamfer
Install the snap ring with the compressor cover downward.
CAUTION
Install the snap ring with the chamfer upward.
Cartridge
assembly
Compressor
cover
KCMB670E
TURBINE HOUSING
Install the cartridge assembly to the compressor cover with them
mating as marked when disassembling.
CAUTION
Take care not to damage the compressor wheel blade.
5-8 AIR CLEANER
3. AIR CLEANER
COMPONENTS
Case assembly
Air cleaner element
Wirng nut
Air cleaner cover

assembly
Dust pan
assembly
T : 0.15 ~ 0.25
kg·m
TORQUE : kg·cm KCYB720A
CHAPTER 6. ENGINE ELECTRICAL
1. GENERAL ............................................................................. 6- 1
2. SPECIFICATIONS ................................................................. 6- 2
3. SERVICE SPECIFICATIONS ................................................ 6- 3
4. TIGHTENING TORQUE ......................................................... 6- 3
5. TROUBLESHOOTING .......................................................... 6- 4
6. ALTERNATOR....................................................................... 6- 11
7. STARTER MOTOR ................................................................ 6- 17
8. GLOW PLUG......................................................................... 6- 26
ENGINE ELECTRICAL SYSTEM 6-1
1. GENERAL
STARTER MOTOR
Starter motor is a reduction drive type.
KD4B6001
ALTERNATOR
Alternator is electronic voltage regulator built-in type.
KD4B6002
6-2 ENGINE ELECTRICAL SYSTEM
GLOW PLUG
Glow plug uses AGS.
Coil
AGS
Identification mark
KD4B6003
2. SPECIFICATIONS
ALTERNATOR
Item Specification Remark
Type Battery voltage sensing

Rated output 12V / 50A
Motor speed 1,000 ~ 10,000 rpm
Voltage regulator type Electronic voltage regulator, with vacuum pump
Regulator setting voltage 14.4 ± 0.3V

Temperature compensated -10 ± 3 mV/°C
STARTER MOTOR
12V / 2.2KW (Generator, Excavator, Loader)

Output
24V / 5KW (Bus aircon)
Number of pinion teeth 13
No-load Terminal voltage 11V

characteristics
Amperage 30A
GLOW PLUG
Item Auto glow
Identification mark Y-115T

Type Sheathed type
3. SERVICE SPECIFICATIONS
ALTERNATOR
Item Standard Limit

Brush length Wear limit
Slip ring O.D. 33mm 32.2mm
Rotor coil resistance (at 20°C) 2.75 ± 0.2Ω
STARTER MOTOR
No-load characteristics voltage (Bus aircon) 11V (23V)
Amperage (Bus aircon) 130A (95A)

Revolution number (Bus aircon) 4500rpm (3300rpm)
Pinion gap 0.5~2.0mm
Commutator O.D. 29.4mm 28.4mm
Undercut 0.5mm 0.2 mm

Outer round 0.05mm 0.1mm
Brush length Wear limit
GLOW PLUG
0.5Ω (Generator, Excavator, Loader)

Resistance AGS
10Ω (Bus aircon)
4. TIGHTENING TORQUE
Item Torque (kg.m) Remark
Lock bolt 1.2 ~ 1.5

Generator support bolt nut 2.0 ~ 2.5
Eye bolt 1.4 ~ 1.9
Starter motor attaching bolt 2.7 ~ 3.4
Glow plug 1.5 ~ 2.0

Glow plug plate attaching nut 0.1 ~ 0.15
5. TROUBLESHOOTING
STARTING SYSTEM
Trouble symptom Probable cause Remedy

Starter spins but engine Starter motor faulty After removing the starter motor, check the
will not crank drive for crack and wear
Flywheel ring gear teeth broken Replace flywheel ring gear or torque con-
verter
Engine will not crank Battery cables loose, corroded or worn out Repair or replace cables
Battery charge low Charge or replace battery

Cables loose or cables wear Tighten or replace cables
Starter motor faulty Repair or replace starter motor
Engine cranks slowly Battery cables loose, corroded or worn out Repair or replace cables
Battery charge low Charge or replace battery
Starter motor faulty Repair or replace starter motor
CHARGING SYSTEM

Low battery Wiring connection loose Tighten loose connections
Overload Check and remove the accessories if re-

quired
Worn battery Replace battery

Generator faulty Repair or replace
Electronic voltage regulator faulty Replace voltage regulato
Battery faulty Check the battery or replace, if necessary

GLOW CONTROL SYSTEM
Engine will not start below Wiring connection loose or bad wiring Repair or replace wiring
50°C
ECT sensor malfunction Replace ECT sensor
Glow plug malfunction Repair or replace glow plug

Glow plug control unit failed Replace glow control unit
After first combustion, en- Wiring connection loose or bad wiring Repair or replace wiring
gine stall or rough idle be-
Glow plug malfunction Check the resistance of glow plug and
low 50°C
replace, if necessary
Glow plug relay malfunction Check the relay and replace, if necessary
Glow plug control unit failed Check the control unit and replace, if nec-
essary
Yellow glow lamp will not Open lamp Replace lamp
turn-ON
Wiring connection loose or bad wiring Repair or replace wiring
Shorted wiring Repair or replace wiring

Glow plug control unit failed Replace control unit, if necessary
VEHICLE INSPECTION
SPECIFICATIONS
B
Diode Charge lamp
trio
L
L
R R
R
D.Power
transistor
Starter coil Battery
F
C
D
Field coil
R
Tr
E
Voltage regulator
Alternator
KD4B6004
NOTE
Register with diode
• According to battery voltage detective type alter-
nator adoption, when the charge warning lamp is
short, to get the charging function, the continuity
circuit of the L terminal (field coil) is installed par-
allel with the circuit of the charge warning lamp.
INSPECTION PREPARATION
Check the following items before inspecting voltage 1. Turn ignition switch to "OFF."
regulator adjusting voltage alternator output current. 2. Disconnect the battery ground cable.
1. Alternator installation 3. Connect a digital voltmeter between the "S(L)"
terminal of the alternator and ground. Connect the
2. Alternator drive belt tension
(+) lead of the voltmeter to the "S(L)" terminal of
3. Battery specific gravity and voltage the alternator. Connect the (-) lead to good ground
or the battery (-) terminal.
4. Fusible link
4. Disconnect the alternator output wire from the gen-
5. Abnormal noise from alternator durng operation
erator "B" terminal.
NOTE 5. Connect a DC ammeter (0 to 100A) in series be-

Use fully charged battery to obtain the stan- tween the "B" terminal and the disconnected out-
dard value. put wire. Connect the (-) lead wire of the ammeter
to the disconnected output wire.
6. Attach the engine tachometer and connect the bat-
tery ground cable.
REGULATED VOLTAGE TEST

1. Set the special tool wiring connector, voltmeter and ammeter as following.
Load
Ignition
switch(IG)
Alternator
Red
Yellow
Battery
Voltmeter Amperemeter
Regulated voltage test

KD4B6005
2. Check as the following procedures.
Determination
No. Check item Operation Cause Remedy
Normal Abnormal
Voltage Ignition switch: 0V Voltage arises Abnormal wiring Correct wiring or
1
between L or alternator repair alternator
OFF
terminal and
earth 0V
Ignition switch: 2~5V
ON Battery voltage Faulty ALTR Repair ALTR
2 Voltage be- Ignition switch: Battery voltage 0V Shor t wiring or Correct wiring or
tween S fusable link replace fusable
OFF
terminal and link
earth
Ignition switch:
ON
Voltage Run the engine 14.4 ±0.5V Highly exceed Abnormal IC Repair ALTR
3
between S and keep the (At 20°C) the standard regulator
terminal and engine at value
earth 2000~3000rpm. Below the If the output fully charge the
(regulator standard value current is 5A or battery.
adjust voltage) more
If the output Repair ALTR

current is 5A or
less, the alterna-
tor is abnormal.
NOTE
• Adjust voltage becomes slightly low in proportion
16 14.6V
to the output current, so it is inspected with low
output current (approx. 5A or less) of IC regulator. 15
Adjust voltage V
• Adjust voltage varies according to the IC regula- 14 14.0V

tor surrounding temperature, so refer to the char-
13
acteristics as shown in the left figure.
• If the battery may be discharged or the head lamp 25°C
is overloaded, the current reads 5A or more. Re- -40 -20 0 20 40 60 80
check the battery lamp this time. IC regulator surface temperature(°C)
KD4B6006
CURRENT OUTPUT TEST

1. Remove battery ground cable.
2. Remove alternator outlet line from alternator "B" terminal. 80A Load
Connect 0-100A test ammeter DC between "B" terminal and 30A
remove outlet line in series.
3. Connect a voltmeter (0 to 20V) between the "B" terminal and Ignition
Battery switch
ground.
4. Attach an engine tachometer. Charge warning lamp
5. Check that the values on voltmeter and battery are the same.
0V is caused by a disconnected wire between the alternator Relay with diode
L
"B" terminal and battery (+), or a blown fusible link, or defec-
S B
tive ground.
6. With headlamp switch ON, start engine. Set headlamps at
high beam and heater blower switch to HIGH. Increase en-
gine speed to 2500 rpm and read the maximum output cur- Voltmeter Amperemeter
rent on the ammeter.
Limit 70% of nominal output current

KD4B6007
NOTE
Read the maximum value quickly as charged current
drops repidly. Nominal output current value is indi-
cated on a plate on the alternator.
7. The value on the ammeter should be over the limit value.

When the value is under the limit and the alternator outlet
wiring [between alternator "B" terminal and battery (+)
terminal] is normal, remove the alternator for inspection.
NOTE
Having headlamps on when checking alternator out-
put current increases the load. Standard current is
generated at low speed of alternator. However, out-
put current is stabilized at about 4000rpm alternator
speed.
Therefore, the output current at 2500 rpm engine
speed exceeds the standard value, and the alternator
can be considered as near normal.
8. Alternator output current changes due to load. Therefore, the

standard output current may not be obtained due th small
electric load despite the charging system being normal. In
this case, increase the load and recheck.
RESULT
1. After output current test, bring engine speed to idle.
Turn ignition switch OFF.
2. Remove battery ground cable.
3. Remove ammeter, voltmeter and engine tachometer.

4. Connect alternator output line to alternator "B" terminal.
5. Connect battery ground cable.
6. ALTERNATOR
COMPONENTS
4
5
T=1.2~1.5 kg·m
T=2.0~2.5 kg·m
1. Lock bolt
2. Nut
3. Support bolt
4. Alternator assembly
5. Alternator brace
KD4B6008
INSTALLATION
ALTERNATOR ASSEMBLY
1. For belt tension, refer to Chapter 5 Engine-Service adjust-
ment procedures.
COMPONENTS
2
5
3
6
8
7
1
13
3 12
11
10
9
[DISASSEMBLY]
1. Pulley
2. Fan
3. Seal
4. Rotor & fan assembly
5. Rear bearing
6. Bearing retainer
7. Front bearing
8. Front bracket
9. Stator assembly
10. Plate
11. Regulator & brush holder [Remarks]
12. Rectifier assembly Assembly is the reverse of disassembly
13. Rear bracket
KD4B6009
DISASSEMBLY
FRONT BRACKET
1. With a screwdriver blade inserted between the front bracket
and stator core, pry it to separate the stator and the front
bracket.
2. If they are hard to separate, lightly strike the bracket with a
plastic hammer while prying with the screwdriver.
KD4B6010
CAUTION
Do not insert the screwdriver too deep as the stator
core could be damaged.
STATOR ASSEMBLY, RECULATOR AND BRUSH Soldering

HOLDER
1. When removing the stator, unsolder the three stator leads
from the main diodes. Rectifier
2. When removing the rectifier from the brush holder, unsolder Plate "B"
Plate "L"
two soldered points.
CAUTION
• When soldering or unsoldering, use care not to
KD4B6011
expose the diode to soldering iron heat for ex-
tended time. Complete soldering or unsoldering
in as short a time as possible.
• Do not overstress the diode leads.
INSPECTION
ROTOR
1. Check the rotor coil continuity. Make sure that there is conti-
nuity between slip rings. Measure the rotor resistance. If it is
excessively small, it indicates a shorted rotor, If without con-
tinuity or shorted, replace the rotor assembly.
Standard value 3 - 5 ohms

KD4B6012
2. Check the rotor coil grounding. Make sure that there is no

continuity between the slip ring and core. Replace the rotor
assembly if there is continuity.
KD4B6013
STATOR
1. Check the stator continuity. Make sure that there is continuity
between coil leads. Replace the stator assembly if there is no
continuity.
KD4B6014
2. Check the coil grounding. Make sure that there is no continu-

ity between the coil and core. Replace the stator assembly if
there is continuity.
KD4B6015
RECTIFIER
1. Inspection of (+) Heat Sink Assembly
Using a circuit tester, check continuity between the (+) heat
sink and the stator coil lead connection terminals. If there is
continuity in both directions, the diode is shorted. Then, re-
place the rectifier assembly.
KD4B6016
2. Inspection of (-) Heat Sink Assembly

Check continuity between the (-) heat sink and the stator coil
lead connection terminals. If there is continuity in both direc-
tions the diode is shorted. Then, replace the rectifier assembly.
KD4B6017
3. Inspection of Diode
Trio With a circuit tester connected to both ends of each diode,
check continuity of the three diodes. If there is continuity or
no continuity in both directions, the diode is damaged. Then,
replace the rectifier assembly.
KD4B6018
BRUSH
1. The brush must be replaced if worn to the wear limit line.
Wear limit line
KD4B6019
2. Unsolder the brush lead wires, and the brush and spring will
come out.
Solder
KD4B6020
3. When installing a new brush, push the brush into the holder
as illustrated and solder the leads.
04570
3314
KD4B6021
REASSEMBLY Rear bracket
ROTOR ASSEMLY
Wire
1. Before installing the rotor on the rear bracket, thread a steel Brush
wire through the small hole provided in the rear bracket to lift
up the brush. After rotor installation, remove the steel wire.
KD4B6022
7. STRATER MOTOR
COMPONENTS
1. Starter motor
2. Nut
3
3. Bolt
KD4B6023
REMOVAL
Remove the starter at the engine room lower portion. S
M B
INSPECTION Battery
PINION GAP ADJUSTMENT

Disconnect
1. Disconnect the field coil wire from the terminal M of the mag- connector Starter
motor
netic switch.
KD4B6024
2. Connect at 12V battery the terminal S and the terminal M.
CAUTION
This test must be performed quickly within 10 sec-
onds to prevent the switch coil from burning.
3. When the battery is connected, the pinion moves out. Now,

push back the pinion with a finger and measure the pinion
stroke (the travel along which the pinion is pushed back). This
Pinion
is the pinion gap.
4. If the pinion gap is not up to specification, adjust by adding or
removing fiber washers between the magnetic switch and front
bracket. Using more washers makes the gap smaller. Pinion
gap
Pinion gap 0.2 ~ 2.0 mm
KD4B6025
PULL-IN TEST OF MAGNETIC SWITCH

The pull-in coil is in good condition if the plunger is pulled in to S
cause the pinion to move out when a battery is connected be-
tween the terminals S and M of the magnetic switch. If the pinion Battery B
12V
does not move out, replace the magnetic switch.
CAUTION Disconnect Starter

• The connector must be disconnected from termi- connector motor
nal M for this test.
KD4B6026
• The test must be finished within 10 seconds.
HOLD-IN TEST OF MAGNETIC SWITCH

+
With a battery connected between the terminal S and body of S
magnetic, manually pull the pinion up to the pinion stopper. The
hold-in coil is in good condition if the pinion remains out when Battery
12V
releasing it.
CAUTION Starter
Disconnect motor
This test must be completed with 10 seconds. connector
KD4B6027
RETURN TEST OF MAGNETIC SWITCH

With a battery connected between the terminal M and body of the M+
magnetic switch, manually pull the pinion out to the pinion stopper.
Body coils are fully operational if the pinion returns immediately Battery
when releasing it.
CAUTION Starter
Disconnect motor
This test must be completed with 10 seconds. connector
KD4B6028
NO-LOAD TEST
Variable resistor
1. Set up a circuit as shown which connects a starter motor,
battery, ammeter, voltmeter, and variable resistance. Ammeter
A
2. The starting motor should be in good condition if it turns
smoothly and steadily when the switch is turned ON with a Starter Battery
maximum variable resistance value. Adjust the variable re- motor V Voltmeter 12V
sistor so that the voltmeter reads 11.5V. If the current and
rpm are out of specification after this adjustment, troubleshoot
according to the table below and take remedial action as KD4B6029
required.
Symptom Possible cause
Large current with low rpm • Contaminated bearing

(torque also being small) • Armature coil rubbing pole piece
• Armature coil shorting
Large current with no rotation • Solenoid switch grounding

• Armature and field coil grounding
• Seized bearing
No current flowing with no • Broken armature and field coils

rotation • Broken brush and pigtail
• Improper contact between brush and commutator
Small current with low rpm (torque • Improper field coil connection (Note, however, that open or improperly
also being small) connected shunt coil only will result in high rpm.)
Large current with high rpm • Shorted field coil

(torque being small)
COMPONENTS
18
13
19
15
23
20
29
12
14
1 16
4
21
22
17
28
5
27
25 26
24
6
11
9
10 7
8
1. Screw 17. Screw

2. Magnetic switch 18. Center bracket
3. Fiber washer 19. Packing
4. Screw 20. Lever spring
5. Screw 21. Washer
6. Rear bracket 22. Gear
7. Brush holder assembly 23. Lever
8. Yoke assembly 24. Snap ring
9. Armature 25. Stop ring
10. Front bearing 26. Pinion gear
11. Rear bearing 27. Spring
12. Screw 28. Pinion shaft assembly
13. Cover 29. Front bracket
14. Snap ring
15. Washer [Remarks]
16. Plate Assembly is the reverse of disassembly
KD4B6030
DISASSEMBLY Magnetic switch

Terminal S
MAGNETIC SWITCH
Terminal M
Remove the field coil wire from the terminal M of magnetic.
Terminal B
Field coil wire
KD4B6031
SNAP RING Plate

Pinion shaft
Measure the pinion shaft end play using the feeler gauge for the Snap ring
purpose of reassembly.
Washer
KD4B6032
SNAP RING AND STOP RING

1. Using an adequate socket, push the stop ring over the snap
Socket
ring.
Pinion gear
Stop ring
KD4B6033
2. Remove the snap ring with a screwdriver, then, remove the stop
ring.
Snap ring
Stop ring
Pinion gear
KD4B6034
CLEANING THE STARTER MOTOR PARTS

1. Do not immerse parts in cleaning solvent. Immersing the yoke
and field coil assembly and/or armature will damage the
insulation. Wipe these parts with a cloth only.
2. Do not immerse the drive unit in cleaning solvent. The over-

run clutch is pre-lubricated at the factory and solvent will wash
lubrication from the clutch.
3. The drive unit may be cleaned with a brush moistened with

cleaning solvent and wiped dry with a cloth.
INSPECTION
CHECKING THE COMMUTATOR
1. Place the armature on a pair of V-blocks, and check the run -
out by using a dial gauge.
Standard value 0 ~ 0.03mm
Limit 0.1mm
KD4B6035
2. Check the outer diameter of the commutator.
Standard value 32 ±0.1mm
Limit 31.4mm
KD4B6036
3. Check the depth of the undercut between segments.
Standard value 0.5mm

Segment Under cut
Limit 0.2mm
Mica
KD4B6037
FIELD COIL OPEN-CIRCUIT TEST

Check for condinuity between field brushes.
There must be continuity.
Yoke
KD4B6038
FIELD COIL GROUND TEST

Check for continuity between the field coil brush and yoke.
Field brush
There must be no continuity.
Yoke
KD4B6039
BRUSH HOLDER
Check for continuity between brush holder plate and brush holder.
There must be no continuity. Brush holder
KD4B6040
OVERRUNNING CLUTCH
1. Ensure that the pinion locks when turned counterclockwise
and turns freely when turned clockwise.
2. Check the pinion for wear and damage.
KD4B6041
BURSHES
1. Check the brush surface in contact with the commutator for
surface roughness. Check also the brush length.
Limit Wear limit line

Wear limit
line
2. If the surface has been refaced or brush has been replaced, KD4B6042
wrap sand paper around the commutator to correct its surface.

3. When removing a worn brush by breaking with pliers, use
care to prevent damage to the pigtail.
New brush
Pigtail Soldering
4. Polish the pigtail end for battery soldering with sand paper. (Brush surface
is free from
5. Insert the pigtail into the hole in a new brush and solder. Make excess solder)
sure that the brush surface is free from excess solder.
Mark
KD4B6043
ARMATURE COIL SHORT TEST Growler
1. Place the armature on a growler.

2. Slowly turn the armature while a thin metal is held above it.
The armature coil is not shorted if the metal does not vibrate.
CAUTION
Before this test, ensure that the armature surface if
free from foreign substances.
KD4B6044
ARMATURE COIL GROUND TEST Growler
Check for insulation between the commutator segment and ar-

mature coil core. There must be no continuity.
KD4B6045
ARMATURE COIL OPEN-CIRCUIT TEST

Check for continuity between segments. There must be
continuity.
KD4B6046
INSTALLATION
STOP RING AND SNAP RING
Using a puller of adequate type, pull the stop ring over the snap
ring.
Stop ring
Pinion gear
KD4B6047
8. GLOW PLUG
COMPONENTS
T=1.5~2.0 kg·m
T=1.5~2.0 kg·m
1. Connector
2. Glow plug plate
3. Glow plug
KD4B6048
REMOVAL
GLOW PLUG
Especially ceramic part of glow plug is so fragile that the screw
should be removed with the hand after unscrewing it several turns
with a tool.
INSPECTION
1. Check for rust on glow plug plate.
2. Check glow plug for damage.
NOTE
Do not use the plug dropped at the height of 10cm or
higher.
3. Check the continuity between the terminal and body as

illustrated. Replace if discontinuity or with large resistance.
Standard value 500Ω(20°C)
NOTE
Remove oil from plug before measuring as glow plug
resistance is very small.
KD4B6049
INSTALLATION
GLOW PLUG
Especially ceramic part of glow plug is so fragile that the screw
should be removed with the hand after unscrewing it several turns
with a tool.
CHAPTER 7. FUEL SYSTEM
1. GENERAL ............................................................................. 7- 1
2. INJECTION NOZZLE ............................................................ 7- 8
3. INJECTION NOZZLE HOLDER ............................................ 7- 10
4. INJECTION PUMP ................................................................ 7- 12
5. TROUBLESHOOTING .......................................................... 7- 15
GENERAL 7-1
1. GENERAL IMFORMATION
OVERALL
A distribution-type fuel injection pump is installed in the front upper case and is driven by the timing belt. The fuel is drawn
from the fuel tank by a pump inside the fuel injection pump and sent to the injection pump through a filter which contains a
water separator. The fuel under pressure enters the pump chamber, where the fuel pressure is regulated by a regulating
valve. From the pump chamber, the fuel is sent through the distributor head passage and then the inlet port in the barrel to
the high pressure chamber above the plunger. The plunger pumps the fuel and the highly pressurized fuel is injected from the
nozzle in accordance with the injection sequence. The excess fuel in the pump housing chamber is returned through the
overflow valve and the overflow pipe to the fuel tank. The injection pump is cooled and lubricated by means of fuel circulation.
The excess fuel at the nozzle holder is also returned through the overflow pipe with unions on the injection pump to the fuel
tank. Since the injection pump is lubricated by fuel, water in the fuel will shorten the pump life to a great degree. Therefore,
special care must be taken to prevent the entry of water, dust, etc. into the system.
High speed adjust bolt
Low speed adjust bolt
Control lever Hole rodadjust screw
Fuel cut solenoid
Drive shaft Plunger
Feed pump
Roller holder
Cam disc
Timer
Plunger spring Delivery valve
EFLB001A
7-2 GENERAL
SPECIFICATIONS

Fuel filter type Cartridge paper filter element type
Fuel injiction Type Distribution type
pump
Turning direction Clockwise as viewed from drive side
1-3-4-2
Injection sequence
Governor type Half All Speed
Feed pump type Vane type
Injection Nozzle type Throttle type

nozzle Holder type Screw-on type
SERVICE SPECIFICATIONS
Item Standard Limit

Injiction pump Injection timing ATDC 5°
Cam lift 2.2mm
Plunger diameter 10mm
Delivery valve opening pressure 21.5kg/cm2
Fuel cut solenoid 12V/8Ω
Injiction Injection orifice (Number-diameter) 1 ~ 1.02mm

Pressure Opening pressure 120kg/cm2 110kg/cm2
Adjust pressure 125 ~ 135kg/cm2
Idle speed 820 ~ 880rpm
GENERAL 7-3
TOQUE SPECIFICATIONS
Item Torque (kg.m)

Injection pipe clamp bolts 0.4 ~ 0.6
Injection pipe union nuts 2.3 ~ 3.7
Pump bracket-to-cylinder block bolts 1.8 ~ 2.5
Injection pump-to-pump bracket bolts 2.0 ~ 2.7
Injection pump mounting nuts 1.5 ~ 2.2

Fuel return pipe nuts 3.0 ~ 4.0
Injection nozzle 5.0 ~ 6.0
ning nut-to-nozzle body 3.0 ~ 5.0
Pump sprocket nut 8.0 ~ 9.0
SPECIAL TOOLS
09310-43000 Injection timing adjustment

Prestroke measuring adapter
D1043000
09314-43100 Removal of nozzle holder

Nozzle holder socket wrench
D1443100
09314-43000 Removal of injection pump sprocket

Injection pump sprocket puller
C1443000
7-4 GENERAL
INSPECTION AND ADJUSTMENT

ACCELERATOR CABLE
1. Warm engine until stabilized at idle.
2. Confirm idle rpm is at prescribed rpm.

3. Stop engine.
4. Confirm there are no sharp bends in accelerator cable.
5. Check inner cable for correct slack.

6. If there is too much slack, adjust slack by the following
procedures.
1) Loosen adjusting nut. Fully close throttle lever.

2) Tighten adjusting nut until throttle lever just starts moving. Adjusting nut
Return 1 turn and lock with lock nut. This adjusts accel-
erator cable play to standard value.
Standard value approx. 1 mm (0.04 in.)
Lock nut
EFLB07A
3) Adjust so that accelerator pedal stopper touches pedal

arm when throttle lever is fully opened.
4) After adjusting, confirm that throttle level fully opens and
closes by operating pedal.
EVACUATION OF AIR FROM FUEL LINE

1. When fuel is drained and re-filled for service.
2. When fuel filter is replaced.
3. When main fuel line is removed.

1) Loosen fuel filter air plug.
2) Place rags around air plug hole. Operate hand pump re-
peatedly until no bubbles come from plug hole. Tighten
air plug.
3) Repeat until hand pump operation becomes stiff.
GENERAL 7-5
EVACUATION OF WATER FROM FUEL FILTER

Water is in the filter when fuel filter indicator lights. Evacuate wa-
ter by the following procedures.
1. Loosen drain plug.
Drain plug
2. Drain water with hand pump. Finger-tighten drain plug.
EFLB009A
INJECTION NOZZLE
INJECTION START PRESSURE
1. Set injection nozzle in nozzle tester and check the following.
2. Move nozzle tester handle at about one stroke per second.
3. The pressure gauge pointer rises slowly and swings when

injection is made. Read the position at which the pointer
started to swing. Check the injection start pressure is the stan-
dard value. EFLB010A
Standard Opening pressure 120kg/cm2

value Adjust preesure 125~135kg/cm2
Limit 112kg/cm2 or more
4. If the nozzle is faulty, disassemble and adjust injection start

pressure to the standard value by changing the shim thickness.
Injection pressure increases by approx. 1,000 kPa (10 kg/
cm2,142 psi) as shim thickness is increased by 0.1 mm (0.
0039 in.).
CAUTION
When disassembling nozzle holder, be careful not to
allow entry of dirt or water.
7-6 GENERAL
5. If the injection start pressure can not be adjusted by chang-

ing the shim thickness, replace nozzle assembly.
Shim
EFLB011A
INJECTION STATUS Not good
Move nozzle tester handle at about 1 stroke per second.

Large
injection Direction Split Intermittent
Good angle imbalance injection injection
EFLB012A
NEEDLE VALVE VIBRATION

Inject on is normal if the characteristic intermittent sound is heard
as the handle is operated, and vibration of the needle valve is felt
at the handle.
GENERAL 7-7
SPRAY
1. Check that the spray is good, as illustrated in the figure, in
the test, the spray may be bolt shaped with a course mist and
fuel may remain. This is phenomenon common in this type of
inspection, and the nozzle function is normal.
2. Move nozzle tester handle at 4 to 6 strokes per second.
3. Confirm the spray is cone shaped with an angle of about 15°.
This indicates a good condition.
EFLB013A
4. If the injection is not good, disassemble nozzle and replace

nozzle tip or entire assembly.
5. Confirm fuel does not drip after injection.
6. If dripping, disassemble injection nozzle and replace nozzle
tip or entire assembly.
NOZZLE OIL-SEAL
1. Maintain internal nozzle pressure (pressure gauge indication
value) with the nozzle tester at 10,000-11,000 kPa (100-110
kg/cm2, 1,422-1,565 psi). Check for fuel leaking from nozzle
tip in this condition.
EFLB014A
2. If there is leakage, disassemble injection nozzle and replace

nozzle tip or entire assembly.
7-8 INJECTION NOZZLE
2. INJECTION NOZZLE
COMPONENTS
0.4 ~ 0.6
4
1
1
3.0 ~ 4.0
5
6
7 0.4 ~ 0.6
8
9
5.0 ~ 6.0 3
2.3 ~ 3.7
1 Injection pipe clamp 6 Fuel return pipe gasket

2 Injection pipe 7 Nozzle holder
3 Fuel return hose 8 Holder gasket
4 Nut 9 Nozzle gasket
5 Fuel return pipe
TORQUE : kg·m
EFLB015A
REMOVAL
Delivery
1. Injection pipe holder
When loosening the union nuts, hold delivery valve holder on Nut
fuel injection pump head or hexagon nut of fuel return pipe
with a wrench to prevent it from rotating along with the union
nut.
CAUTION
Because VE type injection pipe is different from DPC
EFLB016A
type injection pipe, be careful when you install. (VE
type injection pipe is coated yellow)
INJECTION NOZZLE 7-9
2. Fuel return pipe

When removing the fuel return pipe nut, hold the fuel return
pipe by the hexagon nut with a wrench.
CAUTION Nut Fuel return pipe

If you remove the hexagon nut without holding the
fuel return pipe nut, the pipe might be damaged. So
you must remove the hexagon nut with holding re-
turn pipe.
EFLB017A
3. Return holder
Using a deep socket wrench, loosen the injection nozzle and
remove.
09314-43100
CAUTION
Write the number of the cylinder on the injection
nozzle that has been removed. Cover the opening with
an appropriate cap to prevent entry of dust, water and
foreign material into the fuel passage land combus-
tion chamber. EFLB018A
INSTALLATION
NOZZLE HOLDER
1. Clean nozzle holder installation area of the cylinder head.
Holder gasket
CAUTION Nozzle gasket

Gasket groove may cause lack of idle RPM.
EFLB019A
2. Fit a new nozzle gasket and holder gasket into the nozzle
holder hole in the cylinder head.
7-10 INJECTION NOZZLE HOLDER
3. INJECTION NOZZLE HOLDER

COMPONENTS
6
3.5 ~ 4.0
5 1
1 Retaining nut 4
2 Nozzle tip
3 Distance piece
4 Retaining pin
5 Pressure spring
6 Shim
7 Nozzle holder body
TORQUE : kg·m
EFLB020A
DISASSEMBLY
RETAINING NUT
Deep socket
1. Retaining nut Lightly clamp the retaining nut with a cushion wrench
bracket .
2. Hold the retaining nut with a box wrench, and loosen the nozzle
holder body using a deep socket wrench.
EFLB021A
INJECTION NOZZLE HOLDER 7-11
NOZZLE TIP
1. Check the nozzle tip for carbon deposits: Scrape off carbon
deposits with a piece of wood land clean each part with patrol.
After cleaning, keep parts submerged in diesel fuel. Take par-
Plunger
ticular care to protect the nozzle tip needle valve from damage.
2. While the nozzle tip is submerged in diesel fuel, check that Nozzle tip
the needle valve slides smoothly. If the needle valve does not
slide smoothly, replace the nozzle tip. When replacing the
nozzle tip, completely wash off the anticorrosive oil from the EFLB022A
new nozzle tip with clean diesel fuel before using it.
3. Check plunger tip "A" for deformation and breakage. If "A" is

damaged or broken replace it. Check the surface in contact
with the nozzle holder body by using minimum. Check spring
for weakness and breakage.
RETAINING NUT
1. Finger-tighten the nozzle holder body.
2. clamp the retaining nut in a vise with cushion plates. Deep socket
wrench
3. While holding the retaining nut with a box wrench, tighten the
nozzle holder body to the specified torque with a deep socket
wrench.
EFLB021A
7-12 INJECTION PUMP
4. INJECTION PUMP
COMPONENTS
1.0 ~ 1.2
2.3 ~ 3.7
0.4 ~ 0.6
8.0 ~ 9.0
0.4 ~ 0.6
1.5 ~ 2.2
2.0 ~ 2.7
[REMOVAL]
1 Fuel injection pump connector
6 Fuel injection pump sprocket
1A Electrical system connector
7 Fuel injection pump
2 Fuel hose
3 Accelerator cable
4 Fuel injection pipe [Remarks]
5 Upper timming cover Assembly is the reverse of disassembly
TORQUE : kg·m
EFLB024A
INJECTION PUMP 7-13
REMOVAL
FUEL INJECTION PIPE
To remove the fuel injection pipe, refer to Injection nozzle
EFLB025A
FUEL INJECTION PUMP SPROCKET

1. Rotate the crankshaft to place it to the first cylinder piston
compression dead point.
2. Place the belt tensioner to the full loose position of timing
belt..
3. After removing the sprocket mounting nut, remove the sprocket

from the pump drive shaft using the special tool or equivalent
puller. 09314-43000 EFLB026A
CAUTION
Do not tap on the pump drive shaft with a hammer.
4. Leave the sprocket in the timing belt lower cover with the tim-
ing belt engaged.
CAUTION
• Do not burden the timing belt with twist, bend, etc.
• After removing, do not rotate the crank shaft.
• When holding the injection pump, do not pull down
the accelerator lever or fast idle lever.
Do not these levers. It may cause malfunction of
the injection pump.
7-14 INJECTION PUMP
INSTALLATION OF FUEL INJECTION PUMP SPROCKET

Timing mark
When installing the sprocket to the injection pump, be sure the
timing mark is aligned and tighten the nut to the specified torque.
CAUTION
After installing the sprocket, adjust the belt tension.
(Refer to Timing belt of EM group)
No.1 TDC
EFLB027A
5. TROUBLESHOOTING
FUEL TANK AND FUEL LINE
Engine fault caused by Bend and twist of fuel pipes and hoses Correct or replace
low fuel supply
Fuel pipes and hoses clogged Clean or replace
Fuel filter clogged Replace
Water in fuel filter Drain water from the fuel filter
Air in fuel filter Bleed the fuel filter
Fuel tank inside damaged and rusted Clean or replace
Fuel pump fault Replace

7-16 TROUBLESHOOTING
FUEL INJECTION SYSTEM

Engine does not start No voltage at fuel cut-off solenoid on injec- Check for voltage with test light. If necessary,
tion pump replace fuse or faulty wires.
Fuel cut-off solenoid on injection pump loose Tighten solenoid. Check that solenoid clicks
or faulty when key is turned OFF and ON. Replace
faulty solenoid.
No voltage at glow plug bus If test light shows no voltage at bus with key
at "O" position, test relay and wiring.
Glow plug faulty Test and, if necessary, replace glow plug.
Air in fuel system Bleed fuel system.
Injection pump not delivering fue If no fuel emerges from a looseness injec-
tion pipe during cranking, check timing belt
and fuel supply from filter.
Injection pipes misconnected Connect pipes in correct location
Injection timing incorrect Adjust injection timing.
Faulty injection nozzles Check and, if necessary, repair or replace

nozzles.
Faulty injection pump Try to start engine with new pump installed.
If necessary, replace pump permanently.
Idle speed incorrect or idle speed incorrectly adjusted Check and, if necessary, adjust the idle
rough irregular speed.
Accelerator control binding Check that lever on pump is not loose, then
adjust accelerator cable.
Loose fuel hose between filter and injection Replace hose or secure with clamps, bleed
pump air from system.
Inadequate fuel supply owing to clogged fuel Inspect and, if necessary, replace lines and
filter, or fuel return line and injection pipes hoses or replace fuel filter.
leaking, dirty, kinked, or squeezed at con-
nections

injection nozzles. .
Faulty injection pump Try engine at idle with new pump installed. If
necessary, replace pump permanently.

Smoky exhaust Maximum rpm incorrect Check and if necessary, replace injection
(black, blue or white) pump.

injection nozzles.
Faulty injection pump Observe exhaust with new pump installed if
necessary, replace pump permanently.
Poor power output, slow Injection pump accelerator lever loose or not Tighten lever, check that accelerator pedal
acceleration reaching maximum rpm adjusting screw travel is not restricted, then adjust accelera-
(speedometer accurate, tor cable.
clutch not slipping)
Maximum rpm incorrect Check and, if necessary, replace injection
pump.
Inadequate fuel supply owing to clogged fuel Inspect and, if necessary, replace lines and
filter, or fuel return line and injection pipes hoses, replaced fuel filter.
leaking, dirty, kinked, or squeezed at con-
nections
Ice or solidified wax in fuel lines. (winter time Move car to a warm garage until ice or wax
only) has become liquid, then bleed fuel system.
injection nozzles.
Faulty injection pump Check acceleration and speed with new
pump installed. If necessary, replace pump
permanently.
Excessive fuel Fuel leaks Check and, if necessary, replace or tighten

consumption all pipes, hoses and connections.
Return pipe and hose blocked Check return line for kinks and dents. Re-
place faulty lines. If line is clogged, blow it
out with compressed air, then bleed fuel
system.
Idle speed too fast or maximum rpm too high Check and, if necessary, adjust idle speed
or replace injection pump.
Injection timing incorrect Check and, if necessary, repair or replace
injection nozzles.
Faulty injection pump Check fuel consumption with new pump

installed, if unnecessary, replace pump
permanently.

Manual de Servicio Hyundai d4b Foreword.p65

Uploaded by

Copyright:

Available Formats

Manual de Servicio Hyundai d4b Foreword.p65

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Manual de Servicio Hyundai d4b Foreword.p65

Uploaded by

Copyright:

Available Formats

MODEL D4B

Hyundai Motor Co., Inc.

O.E.M Parts Export Team

NOTE, CAUTION, WARNING

NOTE : Information needed in reference to a repair service.

Always wear safety glasses for eye protection.

Do not smoke while working on an engine.

Keep hands and other objects clear of the radiator fan.

2. ENGINE MECHANICAL SYSTEM 2-1

3. LUBRICATION SYSTEM 3-1

4. COOLING SYSTEM 4-1

5. INTAKE AND EXHAUST SYSTEM 5-1

6. ENGINE ELECTRICAL SYSTEM 6-1

7. FUEL SYSTEM 7-1

2. ENGINE IDENTIFICATION NUMBER ..................................... 1- 6

3. TIGHTENING TORQUE OF STANDARD PARTS.................... 1- 7

4. RECOMMENDED LUBRICANTS AND CAPACITIES .............. 1- 8

6. TORQUE SPECIFICATIONS .................................................. 1- 13

7. SPECIAL TOOLS ................................................................... 1- 15

9. CHECKING POINT ................................................................. 1- 20

Timming belt train

Rocker arm shaft

2. ENGINE INDENTIFICATION NUMBER

2) DESCRIPTION OF ENGINE IDENTIFICATION KAXD010C

Engine development order

Engine production sequence number

3. TIGHTENING TORQUE TABLE OF STANDARD PARTS

Bolt nominal Torque (kg m)

EADA010R EADA010S EADA010T EADA010U

M5 0.8 0.3 ~ 0.4 0.5 ~ 0.6

2. The torques shown in the table are not applicable.

Oil pan 0.7 l

Oil filter 0.5 l Above API CD or SG

Coolant Antifreeze for aluminum

Type Diesel engine

Cylinder bore 91.1 mm 91.1 mm

Firing order 1-3-4-2

Camshaft Journal O.D. 29.935 ~ 29.950 mm

Description Specification Limit

O.D. 18.878 ~ 18.898 mm

Intake 7.960 ~ 7.975 mm

Valve Fage angle 45° ~ 45° 3 0 ”

Thickness of valve head Intake 2 mm 1.0 mm

Stem-to-guide clear- Intake 0.03 ~ 0.06 mm

- Front 18.300 ~ 18.467 mm

Front 0.02 ~ 0.06 mm

Description Specification Limit

O.D. 79.0 ~ 79.2 mm

Ring groove width No. 2 ring 2.100 ~ 2.102 2.07 ~ 2.09

Oil ring 4.010 ~ 4.035 3.01 ~ 3.035

No. 1 ring 0.35 ~ 0.50 0.25 ~ 0.40 0.8 mm

Oil ring 0.25 ~ 0.45 0.20 ~ 0.40 0.8 mm

End play 0.05 ~ 0.18 mm 0.2 mm

Out of roundness of journal and pin 0.05 mm less than

Out-of taper of journal and pin 0.015 mm less than

Oil clelarance of journal 0.02 ~ 0.05 mm 0.1 mm

0.25 U.S. 65.735 ~ 65.750 mm

Journal 0.50 U.S. 65.485 ~ 65.500 mm

0.75 U.S. 65.235 ~ 65.250 mm

0.25 U.S. 52.735 ~ 52.750 mm