Question 1 Question 5 The correct answer is: 2000

If a resistor rated at 5 watts Find the total force producing

Question 10
and 6 volts are connected magnetic flux of a circuit
across a battery with an open having 40 V applied across a A circuit of resistance R
circuit voltage of 6 volts. relay coil with 80 turns on 2 ohms and inductance L
What is the internal ohms resistance. Henry has a direct voltage of
resistance of the battery if the 230 volts applied to it. 0.30
resulting current is 0.8 A? The correct answer is: 1,600 second after switching on,
AT the current was found to be 5
The correct answer is: 0.30 amperes. After the current
Question 6
ohm had reached its final value,
What is the force between a the circuit was suddenly
Question 2 point charge 2 x 10^-5 short-circuited. The current
In a test of a 10-ampere coulomb and another 3 x 10^- was again found to be 5
watthour meter having a 6 coulomb when they are 10 ampere at 0.30 second after
constant of 0.40, the disk cm apart in vacuum? short-circuiting the coil. Find
makes 40 revolutions in 55 the value of R and L.
seconds. The average volts The correct answer is: 53.95
and amperes during this kg The correct answer is: 23
period are 116 volts and 10 ohms, 10 H
Question 7
amps. Determine the percent
A constant voltage is applied Question 11
accuracy of this meter at this
to a series RL circuit at t = 0 The open-circuited voltage at
load.
by closing the switch. The terminals of load RL is 30 V.
The correct answer is: voltage across L is 25 volts at Under the conditions of
90.28% t = 0 and drops to 5 volts at t maximum power transfer, the
= 0.025 second. If L = 2 H, load voltage would be ____.
Question 3 what must be the value of R
Calculate the magnetic field in ohms? The correct answer is: 15 V
intensity to produce a
The correct answer is: 128.80 Question 12
magnetic flux density of 10 x
10^-3 Tesla at the center of a How much time is required
Question 8
long solenoid. for electromagnetic energy to
Point charges in air are travel one nautical mile and
The correct answer is: 7958 located accordingly: Q1 = 3 x return to the source?
AT/m 10^-8 C at (0, 0) meters, Q2
= 5 x 10^-8 C at (3, 0) meters The correct answer is: 12.36
Question 4 and Q3 = -5 x 10^-8 C at (0, microseconds
A series circuit consists of a 4) meters. Calculate the field
Question 13
20-ohm resistance, a 150 mH intensity at (3, 4) meters.
inductance and an unknown A magnetomotive force is
capacitance. The circuit is The correct answer is: 59.97 supplied by a current of one
supplied with a voltage v = V/m ampere through 100 turns.
100 sin 377t. Find the value The magnetic circuit consists
Question 9
of capacitance at resonance. of a steel core of 1000
The magnetic flux of 2000 permeability, 10 cm long and
The correct answer is: 47 uF lines is how many in 4 sq. cm area and an air gap
maxwells?
one cm long. What is the field the current drawn by the coil The correct answer is: R/4
intensity at the air gap? alone across a 220 V, 60 Hz
Question 22
source. Determine the
The correct answer is: 124.4 resistance of the non- A 100,000-ohm voltmeter is
oersted inductive resistor. used in measuring the
insulation resistance of a
Question 14
The correct answer is: 3.63 motor. When connected in
A plant has a load of 290 ohms series with the insulation
kilowatt with an average across a 250-Volt line, the
power factor of 70%. The Question 18
instrument reads 1 Volt. What
owner requests you to correct Twenty-four (24) dry cells are is the insulation resistance of
the power factor to reduce its arranged in rows of six (6) in the motor?
power consumption. How series and the four (4) rows
much capacitor kVAR is in parallel. The emf of each The correct answer is: 25.1
required to increase the cell is 1.40 Volt, and internal Mega-ohms
power factor to 90%? resistance of each is 0.08
Question 23
ohm. Determine the current
The correct answer is: 155.39 to an external resistor of 3.2 A lead-sheath cable for
ohms. underground service has a
Question 15
copper conductor (diameter =
The capacitor that stores the The correct answer is: 5.23 A 0.350 inch) surrounded by
charge of 0.5 C at 10 volts 0.20 inch wall of rubber
has a capacitance of ____ Question 19
insulation. Assuming the
farad. Determine the mutual dielectric constant of 4.3 for
inductance between two rubber, calculate the
The correct answer is: 0.05 unity-coupled coils of 6 H and capacitance of the cable per
8 H.
Question 16 mile length.
A 1% d Arsonval meter The correct answer is: 48 H The correct answer is: 0.504
movement has coil and
uF/mile
swamping resistance adding Question 20
to 200 ohms. The full-scale A series RLC circuit when Question 24
voltage is 50 mV. Determine existed by a 10 V sinusoidal An alkaline cell is discharged
the shunt resistance required voltage source of variable at a steady state current of 4
producing 1 A full scale frequency, exhibits amp at 12 hours, the average
current meter. resonance at 100 HZ and has terminal voltage being 1.2
a 3 dB band width of 5 Hz. volt. To restore it to its
The correct answer is: 50.01 The voltage across the original state of charge, a
milli-ohms inductor L at resonance is steady current of 3 amp for
Question 17 20 hrs is required, the
The correct answer is: 200 V
A coil has a resistance of 6 average terminal voltage
ohms and an inductance of Question 21 being 1.44 volts. What is its
0.02 H. When a non-inductive A certain wire has a watt-hour efficiency?
resistor is connected in series resistance R. The resistance
The correct answer is:
with the coil, the current of another wire identical with
66.67%
drawn when connected to the first except for having
220 V DC source is equal to twice its diameter is Question 25
What is the coefficient of = 0.025 inches; A = 6 square to measure 150 volts at full
coupling of two coils whose inches. What is the scale?
mutual inductance is 1 H and capacitance of the capacitor?
whose self-inductances are The correct answer is: 70
1.2 and 2 H? The correct answer is: 4372 kilo-ohms
picofarad
Question 34
The correct answer is: 0.645
Question 30 One leg of a radio tuned
Question 26 The torque of a spring circuit has a capacitance of 1
What is the energy stored in controlled ammeter varies as x 10^-9 F. It is tuned at 200
a 50 uF capacitor if the the square of the current thru kHz. What is the inductance
impressed voltage is 220 it. If the current of 5 amperes of the other leg in Henry?
volts? produces deflection of 90
degrees, the deflection in The correct answer is: 6.33 x
The correct answer is: 1.21 degrees for a current of 3 10^-4
joules
Question 35
The correct answer is: 32.4
Question 27 A piece of conductor 10 cm
A wound rotor motor, 7.5 HP, Question 31 long moves across a
230 volts, 3-phase takes a Given the following line magnetic field of 10,000
line current of 18.4 ampere, voltages and two load gauss at a velocity of 120
when operating at rated impedances: Vab = 117 cis cm/sec. What voltage
output at an efficiency of (0 deg) V; Vbc = 117 cis (240 appears across the
88%. Calculate the indication deg) V; Vca = 117 cis (120 conductor?
on the wattmeter when this is deg) V; Zab = 5 + j12 ohms;
inserted to measure power by Zbc = 13 + j0 ohms. Solve for The correct answer is: 0.12 V
the T-method. the current in line c.
Question 36

The correct answer is: 3.179 The correct answer is: 17.95 A certain capacitor is charged
kW A at 48 volts after which its
stored energy is 5.76 x 10^-2
Question 28 Question 32 joules. What is the
A coil of 10 ohms resistance A certain process uses warm capacitance of the capacitor?
and 0.1 H inductance is water at rate of 2 liters per
connected in parallel with a minute. The water enters at The correct answer is: 50 uF
capacitor of unknown electric heater at 25 deg C to
Question 37
capacitance. If the total 50 deg C. Assuming no heat
A dc ammeter has an internal
impedance of the losses, what is the wattage of
resistance of 0.1 ohm. A
combination is 100 ohms, the heater?
shunt of 1.010 x 10^-3 ohm is
determine the value of the
The correct answer is: 2420 connected to the ammeter.
capacitance.
What is the multiplier of the
Question 33 setup?
The correct answer is: 50 uF
A voltmeter with an internal
Question 29 resistance of 5000 ohms is The correct answer is: 100
Question text calibrated to read 10 volts at
Question 38
A parallel plate capacitor has full-scale. How much series
Two series connected 7 H
the following values: k = 81, d resistance is needed in order
inductors are adjacent to
each other. Their coefficient The correct answer is: 10 The correct answer is: 0.50
of coupling is 0.64. What is Amperes uF
the value of M?
Question 43 Question 47
The correct answer is: 4.48 H A moving coil instrument
having meter resistance of 5
Question 39 A copper wire has a
ohms is to be used as a
Two point charges Q1 = 50 voltmeter 0 - 100 volts. If the resistance of 2.4 ohms at 20
microcoulombs and Q2 = 10 full-scale deflection current is degrees Celsius. Find the
microcoulombs are located at 10 mA, the required series resistance at 75 degrees
(-1, 1, 3) and (3, 1, 0) meters resistance is Celsius. Resistance
respectively. Find the temperature coefficient at 20
magnitude of the force on The correct answer is: 9995 degrees Celsius is
Q1. ohms 0.034/degrees Celsius.

The correct answer is: 4.9 N Question 44 The correct answer is: 6.89
A current transformer has a ohms
Question 40
single turn primary and a 200
An electronic device draws Question 48
turn secondary and is used to
300 watts from its 24 volt measure a.c. current with the A three-phase 230-V circuit
power source. Find effective help of a standard 5-A a.c. serves two single-phase
resistance. ammeter. These loads, A and B. Load A is an
arrangements can measure a induction motor rated 8 hp,
The correct answer is: 1.92 230 V, 0.70 pf, 0.90
line current of up to ____
ohms efficiency, which is connected
ampere,
across lines a and b. Load B
Question 41
The correct answer is: 1000 draws 5 kW at 1.0 pf and is
A magnetic circuit consists of
connected across lines b and
silicon steel of 3000 Question 45
c. Assume a sequence of a-
permeability, of 10 cm length A series loop contains the b-c, solve for the total power
and a cross section of 1.5 sq. following circuit elements in factor of the load.
cm and an air gap of the order: an 8-Volt source, 2 k
same cross section and of 2 ohms resistor. A 3 k ohms The correct answer is: 0.864
cm length. A 1/2 ampere resistor, a 16-Volt source and
current flows through the Question 49
a 7 k ohms resistor. What is
5000 turn coil. What is the the voltage across the 2 k Ten impedances connected
field intensity at the air gap? ohms resistor? Source in parallel draw the following
Voltage are additive. individual current: 5 cis(0
The correct answer is: 1567 deg), 5 cis (5 deg), 5 cis (10
oersted The correct answer is: 4 Volts deg), 5 cis (15 deg), 5 cis (20
deg), 5 cis (25 deg), 5 cis (30
Question 42 Question 46
deg), 5 cis (35 deg), 5 cis (40
Find the current in a If two 0.25 uF capacitors are deg), 5 cis (45 deg). What is
conductor through which 2.5 connected in parallel, what the equivalent power factor of
x1 0^21 electrons pass in 10 will be the total effective the circuit?
seconds. capacitance?
The correct answer is: 0.924
Question 50 78.4 cis (214 deg) A, Ic = 75 A magnetic coil produces
If an oscilloscope with a cis (80 deg) A. If the voltages 100,000 Maxwell with 2,000
vertical deflection of 0.1 volt impressed on the load are turns and with a current of 2
rms per centimeter (cm), is balanced 3-phase, having a A. The voltage is cut-off and
used in conjunction with a 10 magnitude of 4140 volts line the flux collapses in 0.01 sec.
ohm shunt resistor to to line, solve for the total What is the average voltage
measure a 25 milli-amp power in kW. that will appear across the
current, compute the vertical coil?
deflection? Select one:
The correct answer is:
The correct answer is: 2.5 cm The correct answer is:
506.85 200 V
Question 1
Question 7

One ampere-turn is
equivalent to _____ gilberts. A conductor 0.5 m long is
moved at right angle to a
The correct answer is: uniform field strength of 0.12
Wb/m^2 at a speed of 0.2
1.26 Question 4
meter per second. Find the
value of emf induced.
A conductor, 50 mm long,
moves at a velocity of 2.5 The correct answer is:
Question 2 meters per second across a
magnetic field of 0.90 0.012 V
A parallel plate capacitor with Wb/m^2. What is the voltage
air between its plates is generated? Question 8
charged until the potential
difference V appears across The correct answer is: Question text
it. Another capacitor having 0.1125 V Two metallic plates
hard rubber (dielectric separated by 1 cm are
constant = 3) between its Question 5
connected across a 12 V
plates but otherwise identical, battery. A certain material is
is also charged to the same To roughly check his kWh
inserted completely filling the
potential difference. If the meter an electrician hook-up
space between the plates
energy of the first capacitor is a wattmeter, he switched on
and the charge on each plate
W, that of the second is the load, he counted 5 rev in
observed to double. What is
18 sec, the meter constant is
the dielectric constant of the
The correct answer is: 3.2. The wattmeter reads 368
plastic material?
Watts. What is the error of
3W the meter? The correct answer is:

Question 3 The correct answer is: 2

8% slower Question 9
A 3-phase, 3-wire load draws
the following line currents: Ia
Question 6
= 60 cis (330 deg) A, Ib =
A certain capacitor is charged susceptance of 8 mhos and a permeability and an air gap.
at 48 volts after which its capacitive reactor having a The length of the steel core is
stored energy is 5.76 x 10^-2 susceptance of 5 mhos. What 10 cm and the air gap is 2
joules. What is the is the impedance of the cm. Both have same cross
capacitance of the capacitor? section of 1.5 sq cm. A
circuit? current of 1/2 ampere flows
The correct answer is: through the windings to
The correct answer is:
produce 2351 maxwells flux.
50 uF
0.16 + j0.12 ohms How many turns are there in
the coil?
Question 10
Question 13
The correct answer is:
To test the accuracy of a
Question text
kilowatt-hour meter an 5,000 turns
electrician used a wattmeter. A current transformer has a
He found out that the meter single turn primary and a 200 Question 16
makes 5 revolutions in 18 turn secondary and is used to
seconds. The meter constant measure a.c. current with the A one-meter rod of 2 cm
is 3.2. What is the help of a standard 5-A a.c. diameter is drawn until its
percentage error if the ammeter. These resistance is 100 times the
wattmeter reading is 3368? arrangements can measure a initial resistance, its length
line current of up to ____ afterward is?
The correct answer is:
ampere,
The correct answer is:
5% slower The correct answer is:
12.5 m
Question 11 1000
Question 17
A 5-ohm resistance is Question 14
connected in parallel with a Point charges in air are
10-ohm resistance. Another When two inductors are located accordingly: Q1 = 3 x
set, a 6-ohm and an 8-ohm connected in series aiding, 10^-8 C at (0, 0) meters, Q2
resistances are also their total inductance is 40 = 5 x 10^-8 C at (3, 0) meters
connected in parallel. The mH, when connected series and Q3 = -5 x 10^-8 C at (0,
two sets are connected in opposing the inductance is 4) meters. Calculate the field
series. What is the equivalent 17.5 mH. What is the value of intensity at (3, 4) meters.
resistance?
mutual inductance? Feedback
The correct answer is:
The correct answer is:
The correct answer is:
6.76 ohm
59.97 V/m
562.5
Question 12
Question 18
Question 15
A parallel circuit consists of a
An isolated sphere 10 cm in
resistor having a A magnetic circuit consists of
radius is charged in air to 500
conductance of 4 mhos, an silicon steel of 3000
inductive reactor having a
Volts. How much charge is Three loads, units A, B and C The correct answer is:
required? are connected in parallel and
take currents that are 3 mH
The correct answer is: respectively 12, 10 and 15 A
respectively. Assuming Ia to Question 26
5.563 nC be the reference phasor. Ib
leads Ia by 30 deg and Ic An ammeter has a range of 0
Question 19
lags behind Ia by 65 deg, - 10 amps. What is shunt
calculate the total (resultant) resistance to be connected if
A 120-V per phase, three- the range is increased to 100
current.
phase Y-connected source amps? The internal
delivers power to the The correct answer is: 28.33 resistance of the ammeter is
following delta-connected A 0.10 ohms.
load: Phase 1 = 40 cis (0
deg), Phase 2 = 20 cis (-60 Question 23 The correct answer is:
deg), Phase 3 = 15 cis (45
deg). Solve for the three line 0.0111 ohms
One (1) kW is equal to ____
currents. hp.
Question 27
The correct answer is: The correct answer is:
An ammeter rated 5 A,
13.49 A, 9 A, 22.45 A 1.34 having a resistance of 0.5
ohm, is to be converted into a
Question 20 Question 24 200-V voltmeter by
connecting a resistor in
A voltmeter using a 20 micro- A certain 50 micro-A meter series with the ammeter.
amp meter movement has an movement has a resistance Calculate the value of this
ohm/V rating of of 90 ohms. What value of resistance.
series multiplier is needed to
The correct answer is: The correct answer is:
make an instrument that will
read 5 volts (maximum)?
50 kilo-ohms/V 39.5 ohms
The correct answer is:
Question 21 Question 28
99.91 kilo-ohms
In a series RC circuit, the A battery is formed of five
voltage across the capacitor Question 25 cells joined in series. When
and the resistor are 60 and the external resistance is 4
80 volt respectively, the total A coil of inductance 8 mH, ohms, the current is 1.5 A
voltage is produces 80 uWb of and when the external
magnetic flux. Of this total resistance is 9 ohms, the
The correct answer is:
flux, 60 uWb are linked to a current falls to 0.75 A. Find
100 V second coil of inductance 2 the internal resistance of
mH, how much is the mutual each cell.
Question 22 inductance between the
coils? The correct answer is:

0.2 ohm
Question 29 Question 33 A galvanometer has a
resistance of 300 ohms.
How much current is A copper wire of unknown What is the ohmic resistance
necessary for a coil of 200 length has a resistance of to make it read one is to ten?
turns to provide a 400 0.80 ohm. By successive
ampere turn magnetizing passes through drawing dies, The correct answer is:
force? the length of the wire is
33.33
increased by 2 1/2 times its
The correct answer is: original value. Assuming that
Question 37
resistivity remains unchanged
2A
during the drawing process,
To double the current range
determine the new value of
Question 30 of a 50-micro-amp, 2 kilo-
its resistance.
ohm moving coil meter
Three resistors having the The correct answer is: movement, the shunt
same resistances are resistance should be
connected in star and across 5 ohms
480 V 3-phase lines. To what The correct answer is:
value should the line voltage Question 34
2 kilo-ohms
be changed to obtain the
same line currents with the The voltage across the Question 38
resistors delta-connected? resistor, inductor and
capacitor in series is 60 V, 90 A single-phase three wire, 60
The correct answer is:
V and 10 V respectively. Hz, 220 V, watthour meter
160 V What is the voltage across has a disc constant of 1.2.
this circuit? Determine the energy
Question 31 recorder by the meter after
The correct answer is:
18,000 revolutions of the
If three shielded 100 mH coils 100 V disc.
are connected in series, what
is the total effective The correct answer is:
Question 35
inductance?
21.6 kW-hr
A capacitor with air between
The correct answer is:
its plates has a capacitance Question 39
300 mH of 3 uF. What is the
capacitance when wax of A three-phase balanced load
Question 32 dielectric constant 2.8 is draws a line current of 80 A
between the plates? at 0.90 lagging power factor.
If relative permittivity of mica Solve for the minimum size in
The correct answer is:
is 5, its absolute permittivity kVAR of the capacitor bank
is 1.07 uF needed to raise the power
factor to 0.96 leading, if the
The correct answer is:
Question 36 line to line voltage is 13,200
5*(permittivity of free volts.
space)
The correct answer is: The correct answer is: Four 3 pCoul spheres are in
1338.25 corners of square q 1 cm on
1.25 sin (wt + 75.5 deg) sides. Find the force in
Question 40 Newton?
Question 44

Calculate the equivalent The correct answer is:

power in watt of 100 joules A capacitor of 2 microfarad
with an initial charge q0 is 15.5 x 10^(-10)
per second.
connected across the
Question 48
The correct answer is: terminals of a 10 ohm resistor
and the switch is closed at t =
100 watts 0. Find q0 (micro-coulomb) if Four capacitors A, B, C and
the transient power in the D are connected across a 15-
Question 41 V DC source. The charges
resistor is known to be pR =
360*e^(-10^-5*t) accumulated in A, B and C
The current in an electric are equal to 2000, 750 and
lamp is 5 amperes. What The correct answer is: 1500 uC, respectively. If the
quantity of electricity flows total capacitance of the
toward the filament in 6 120 combination is known to be
minutes? 35 uF, how much charge is
Question 45
accumulated in capacitor D?
The correct answer is:
A piece of conductor 10 cm The correct answer is:
1800 C long moves across a
magnetic field of 10,000 1000 uC
Question 42
gauss at a velocity of 120
Question 49
cm/sec. What voltage
A one-meter of annealed appears across the
copper 2.5 cm in diameter is conductor? A series RLC circuit with R =
drawn until its resistance is 1 k-ohm, L = 1 H and C =
100 times the initial The correct answer is: 6.25 uF is suddenly
resistance, its diameter connected across a 24 V dc
afterward is? 0.12 V source. At t = 0, i = 0 and q =
0. Determine the current after
The correct answer is: Question 46
0.01 sec.
0.25 cm Calculate the magnitude of The correct answer is:
the electric field at a point
Question 43 5.40 mA
that is 30 cm from a point
charge Q = -3.2 x 10^-6 C.
A coil of 50-ohm resistance Question 50
and of 150-mH inductance is The correct answer is:
connected in parallel with a Three impedances each 10 +
50-uF capacitor. If the source 3.0 x 10^5 N/C j5 ohms are connected delta
voltage is 100 sin (wt + 30 on a balanced three-phase
Question 47
deg), what is the equation of source. If the equation of the
the line current? phase Van = 120 sin wt.
What is the equation of the
line current through the
impedance connected across
phase A and B?

The correct answer is:

18.59 sin (wt + 3.44

degrees)
 A dc ammeter has an internal Feedback arrangements can measure a
resistance of 0.1 ohm. A line current of up to ____
shunt of 1.010 x 10^-3 ohm is The correct answer is: 111 A ampere,
connected to the ammeter.
What is the multiplier of the Find the voltage drop Select one:
setup? developed across D Arsonval
meter movement having an a. 1000
Select one: internal resistance of 1 kilo-
ohms and full current of 150 b. 200
a. 10 micro amperes.
c. 40
b. 80 Select one:
d. 5000
c. 100 a. 150 mV
Feedback
d. 50 b. 150 V
The correct answer is: 1000
Feedback c. 150 kV
A copper disc of radius 0.1m
The correct answer is: 100 d. 150 micro V is rotated about its centre
with 20 revolutions per
Find the flux density having a Feedback second in a uniform magnetic
flux of 20,000 Maxwells field of 0.1 T with its plane
through a perpendicular area The correct answer is: 150 V perpendicular to the field.
of 2 cm squared. The emf induced across the
A coil of 15 H inductance radius of the disc is
Select one: and 10 ohms resistance is
suddenly connected to a 20 Select one:
a. 10,000 gauss volts DC source by closing
switch. The energy stored in a. pi/20 volt
b. 22,000 gauss the magnetic field 2 seconds
after the switch is closed is; b. pi/10 volt
c. 40,000 gauss
Select one: c. 10pi millivolt
d. 20,000 gauss
a. 10 joules d. 20pi millivolt
Feedback
b. 30 joules Feedback
The correct answer is: 10,000
gauss c. 20 joules The correct answer is: 20pi
millivolt
The average value of a d. 16.43 joules
sinusoidal current is 100 A. A coil of 250 turns is wound
Its r.m.s. value is ____. Feedback on a closed iron ring whose
cross sectional area is 20
Select one: The correct answer is: 16.43 cm^2 and mean length of 100
joules cm. Determine the energy
a. 111 A stored in the magnetic field if
A current transformer has a a current of 2 A is passed
b. 63.7 A single turn primary and a 200 through it. Assume a
turn secondary and is used to permeability of iron is 900.
c. 70.7 A measure a.c. current with the
d. 141.4 A help of a standard 5-A a.c. Select one:
ammeter. These
a. 1.88 J If a current of 5A flowing in going into the wattmeter is
a coil of inductance 0.1 H is 115 volts. What is the MW
b. 2.03 J reversed in 10 ms, e.m.f. indicated when the wattmeter
induced in it is ____ volt. reads 800 watts?
c. 2.83 J
Select one: Select one:
d. 3.12 J
a. 1 a. 19.2 MW
Feedback
b. 100 b. 192 MW
The correct answer is: 2.83 J
c. 50 c. 150 MW
A balanced 3-phase load
draws 75 amperes line d. 10,000 d. 15.0 MW
current at 230 volts line to
line and 0.848 lagging power Feedback Feedback
factor. If the two-wattmeter is
used, solve for the readings The correct answer is: 100 The correct answer is: 192
of the two wattmeters. MW
If an oscilloscope with a
Select one: vertical deflection of 0.1 volt Question 14
rms per centimeter (cm), is
a. 17.24 kW, 8.10 kW used in conjunction with a 10 Correct
ohm shunt resistor to measure
b. 15.32 kW, 10.02 kW a 25 milli-amp current, Mark 1.00 out of 1.00
compute the vertical Flag question
c. 17.86 kW, 7.48 kW deflection?
d. 16.42 kW, 8.92 kW Question text
Select one:
Feedback The ohmic resistance of a
a. 25 cm large magnetic contactor is
The correct answer is: 17.24 b. 0.25 cm measured to be 20 ohms. A
kW, 8.10 kW 230 V is impressed on the
c. 0.025 cm contractor and the current is
The decay of a coil is taken as 3.2 A. Neglecting
recorded, it is found that iL = d. 2.5 cm core loss, determine the
10 A at t = 2ms and iL = 3.58 inductance of the contractor
A at t = 6 ms. what is the Feedback in mH?
time constant of the coil.
The correct answer is: 2.5 cm Select one:
Select one:
Question 13 a. 261
a. 6 ms
Correct b. 315
b. 4 ms
Mark 1.00 out of 1.00 c. 251
c. 2 ms
Flag question d. 183
d. 3 ms
Question text Feedback
Feedback
At a 115 kV substation, the The correct answer is: 183
The correct answer is: 4 ms PT ratio is 100 and the CT
ratio is 1200/5. The potential Question 15
Incorrect The correct answer is: 1.44 x a. 1 ohm
10^-3 J
Mark 0.00 out of 1.00 b. 0.25 ohm
Question 17
Flag question c. 4 ohms
Correct
Question text d. 2 ohms
Mark 1.00 out of 1.00
A coil of 40 ohms resistance Feedback
has an inductance of 100 mH Flag question
and is connected in parallel The correct answer is: 0.25
with a 40 uF capacitor. What Question text ohm
is the resonance frequency of
the circuit? A battery is formed of five Question 19
cells joined in series. When
Select one: the external resistance is 4 Correct
ohms, the current is 1.5 A
a. 79.6 Hz and when the external Mark 1.00 out of 1.00
resistance is 9 ohms, the Flag question
b. 47.75 Hz current falls to 0.75 A. Find
the internal resistance of each Question text
c. 60 Hz cell.
d. 23.7 Hz A parallel plate capacitor has
Select one: the following values: k = 81,
Feedback d = 0.025 inches; A = 6
a. 0.3 ohm square inches. What is the
The correct answer is: 47.75 b. 0.2 ohm capacitance of the capacitor?
Hz
c. 0.5 ohm Select one:
Question 16
d. 1.0 ohm a. 437.2 picofarad
Correct
Feedback b. 4372 picofarad
Mark 1.00 out of 1.00
The correct answer is: 0.2 c. 4.372 picofarad
Flag question ohm d. 43.72 picofarad
Question text Question 18 Feedback
A 20 uF capacitor is charged Correct
by a 12-V battery. What is The correct answer is: 4372
the stored energy in the Mark 1.00 out of 1.00 picofarad
capacitor?
Flag question Question 20
Select one:
Question text Incorrect
a. 1.07 x 10^-3 J
Four cells, each of internal Mark 0.00 out of 1.00
b. 2.88 x 10^-3 J resistance 1 ohm, are Remove flag
connected in parallel. The
c. 2.88 x 10^-2 J battery resistance will be Question text
d. 1.44 x 10^-3 J ____
An ammeter has a range of 0
Feedback Select one: - 10 amps. What is shunt
resistance to be connected if Correct c. none of the above
the range is increased to 100
amps? The internal resistance Mark 1.00 out of 1.00 d. 54 ohms
of the ammeter is 0.10 ohms.
Flag question Feedback
Select one:
Question text The correct answer is: 2
a. 1.111 ohms ohms
A wye-connected, balanced
b. 2.111 ohms three-phase load draws 75 A Question 24
from 230 V, 60 Hz source.
c. 0.111 ohms To measure the total power, Correct
two wattmeters are connected
d. 0.0111 ohms in lines A and C and reads Mark 1.00 out of 1.00
8,625 W and 17,250 W, Flag question
Feedback respectively. Determine the
The correct answer is: 0.0111 impedance of the balanced Question text
ohms load.
If relative permittivity of
Question 21 Select one: mica is 5, its absolute
permittivity is
Incorrect a. 1.77 cis (-30 deg) ohms
Select one:
Mark 0.00 out of 1.00 b. 3.07 cis (30 deg) ohms
a. (permittivity of free
Remove flag c. 1.77 cis (30 deg) ohms space)/5

Question text d. 3.77 cis (-30 deg) ohms b. 8.854 x 10^-12

A series RLC circuit is Feedback c. 5*(permittivity of free

consisting of 20 ohms The correct answer is: 3.77 space)
resistor, 20 mH inductor, 100 cis (-30 deg) ohms
uF in series is connected to a d. 5/(permittivity of free
100 V dc source. Find the Question 23 space)
additional resistance just to
prevent the oscillation of the Correct Feedback
resulting transient current The correct answer is:
Mark 1.00 out of 1.00
Select one: 5*(permittivity of free space)
Flag question
a. 82.8 ohms Question 25
Question text
b. 26.2 ohms Correct
If 18 resistances, each of
c. 282 ohms value 36 ohms, are connected Mark 1.00 out of 1.00
in parallel, then the total Flag question
d. 8.28 ohms resistance is ____
Feedback Question text
Select one:
The correct answer is: 8.28 If two 0.25 uF capacitors are
a. 2 ohms connected in parallel, what
ohms
b. 36 ohms will be the total effective
Question 22 capacitance?
Select one: Question text Question 29

a. 0.50 uF A certain capacitor is charged Incorrect

at 48 volts after which its
b. 0.125 uF stored energy is 5.76 x 10^-2 Mark 0.00 out of 1.00
joules. What is the
c. 0.624 uF capacitance of the capacitor? Flag question

d. 2.5 uF Select one: Question text

Feedback a. 50 uF A 12 micro-farad capacitor

charged at 500 Volts and a 6
The correct answer is: 0.50 b. 60 uF micro-farad capacitor
uF charged at 250 Volts are
c. 30 uF connected in parallel. What is
Question 26 the potential difference in the
d. 2 F combination?
Incorrect
Feedback Select one:
Mark 0.00 out of 1.00
The correct answer is: 50 uF a. 750 Volts
Remove flag
Question 28 b. 417 Volts
Question text
Incorrect c. 500 Volts
A milliameter with full-scale
deflection of 1 mA and a Mark 0.00 out of 1.00 d. 450 Volts
resistance of 25 ohms was
used to measure an unknown Remove flag Feedback
current by shunting the meter
with a 1-ohm resistor. The Question text The correct answer is: 500
meter then reads half-scale. Volts
What is the unknown value? To roughly check his kWh
meter an electrician hook-up Question 30
Select one: a wattmeter, he switched on
the load, he counted 5 rev in Correct
a. 12.5 mA 18 sec, the meter constant is
3.2. The wattmeter reads 368 Mark 1.00 out of 1.00
b. 130 mA Watts. What is the error of
the meter? Flag question
c. 125 mA
Select one: Question text
d. 13 mA
a. 8% slower A coil has a resistance of 6
Feedback ohms and an inductance of
b. 8% faster 0.02 H. When a non-
The correct answer is: 13 mA inductive resistor is
c. 5% faster connected in series with the
Question 27 coil, the current drawn when
d. 5% slower connected to 220 V DC
Correct
source is equal to the current
Feedback drawn by the coil alone
Mark 1.00 out of 1.00
The correct answer is: 8% across a 220 V, 60 Hz source.
Flag question slower
Determine the resistance of Question text Feedback
the non-inductive resistor.
Given: Vab = 240 cis (0 deg) The correct answer is: 80%
Select one: V, Vbc = 240 cis (240 deg)
V, Vca = 240 cis (120 deg) Question 34
a. 3.69 ohms V, Zab = 6 + j8 ohms, Zbc =
5 + j8.6 ohms, Zca = 10 + j0 Correct
b. 3.96 ohms ohms. Solve for the three line Mark 1.00 out of 1.00
c. 6.39 ohms currents Ia, Ib and Ic.
Flag question
d. 3.63 ohms Select one:
Question text
Feedback a. Ia = 45 A, Ib = 43 A, Ic =
20 A Two coils A and B are
The correct answer is: 3.63 connected in series such that
ohms b. Ia = 48 A, Ib = 43 A, Ic = the total inductances are 1 H
24 A and 0.4 H depending on the
Question 31 direction of current in the
c. Ia = 48 A, Ib = 42 A, Ic =
24 A coils. Calculate the coupling
Incorrect factor between the coils if the
Mark 0.00 out of 1.00 d. Ia = 45 A, Ib = 42 A, Ic = self-inductance of coil B is
20 A 0.5 H.
Remove flag
Feedback Select one:
Question text
The correct answer is: Ia = 48 a. 35%
Two similar charges of 250 A, Ib = 42 A, Ic = 24 A
statC are situated on small b. 85%
spheres 15 cm apart. What is Question 33
c. 47%
the potential at point midway
between the spheres? Correct
d. 79%
Select one: Mark 1.00 out of 1.00
Feedback
a. 66.7 statV Flag question
The correct answer is: 47%
b. 16.7 statV Question text
Question 35
c. 25 statV A 25 ohms resistor connected
in series with a coil of 50 Correct
d. 33.3 statV ohms resistance and 150 mH Mark 1.00 out of 1.00
inductance. What is the
Feedback power factor of the circuit? Flag question
The correct answer is: 16.7 Select one: Question text
statV
a. 75% A moving coil instrument
Question 32 having meter resistance of 5
b. 80% ohms is to be used as a
Correct voltmeter 0 - 100 volts. If the
c. 90%
Mark 1.00 out of 1.00 full-scale deflection current is
d. 85% 10 mA, the required series
Flag question resistance is
Select one: Question text The correct answer is: 682

a. 9995 ohms A capacitor whose plates is Question 39

20 cm x 3.0 cm and is
b. 1000 ohms separated by a 1.0-mm air Correct
gap is connected across a 12-
c. 20 ohms V battery. Determine the Mark 1.00 out of 1.00

d. none of these charge accumulated on each Flag question

plate after a long time.
Feedback Question text
Select one:
The correct answer is: 9995 Two capacitors 30 and 10
ohms a. 8.1 x 10^-11 C microfarad are connected in
b. 5.3 x 10^-12 C series, what is the total
Question 36 capacitance?
Correct c. 6.4 x 10^-10 C
Select one:
Mark 1.00 out of 1.00 d. 7.2 x 10^-9 C
a. 40 microfarad
Flag question Feedback
b. 7.5 microfarad
Question text The correct answer is: 6.4 x
10^-10 C c. 20 microfarad
Given the following line d. 300 microfarad
voltages and two load Question 38
impedances: Vab = 117 cis (0 Incorrect Feedback
deg) V; Vbc = 117 cis (240
deg) V; Vca = 117 cis (120 Mark 0.00 out of 1.00 The correct answer is: 7.5
deg) V; Zab = 5 + j12 ohms; microfarad
Zbc = 13 + j0 ohms. Solve Remove flag
for the current in line c. Question 40
Question text
Select one: Correct
The power factor of a load on
a. 18.46 A a 120 volt, 60 Hz source is Mark 1.00 out of 1.00
raised from 0.707 to 0.866 Flag question
b. 16.62 A lagging by connecting a 53
micro-farad capacitor across Question text
c. 17.41 A the load. What is the true
d. 17.95 A power of the load in watts? If a current of 5 A flows
through a long wire of radius
Feedback Select one: 0.004 meter, what is the
magnetic intensity produced
The correct answer is: 17.95 a. 862 0.02 meter away from the
A b. 682 surface of the wire?

Question 37 c. 286 Select one:

Correct d. 268 a. 39.80 AT/m

Mark 1.00 out of 1.00 Feedback b. 33.17 AT/m

Flag question c. 66.34 AT/m

d. 19.70 AT/m b. 40 joules 90 ohms. What value of
series multiplier is needed to
Feedback c. 10 joules make an instrument that will
read 5 volts (maximum)?
The correct answer is: 39.80 d. 20 joules
AT/m Select one:
Feedback
Question 41 a. 102 kilo-ohms
The correct answer is: 20
Correct joules b. 99.91 kilo-ohms
Mark 1.00 out of 1.00 Question 43 c. 98 kilo-ohms
Flag question Correct d. 110 kilo-ohms
Question text Mark 1.00 out of 1.00 Feedback
The resistance of 120 meters Flag question The correct answer is: 99.91
of wire is 12 ohms. What is kilo-ohms
its conductance? Question text
Question 45
Select one: A magnetic coil produces
100,000 Maxwell with 2,000 Correct
a. 6 siemens turns and with a current of 2
A. The voltage is cut-off and Mark 1.00 out of 1.00
b. 12 siemens the flux collapses in 0.01 sec.
What is the average voltage Flag question
c. 0.0521 siemens that will appear across the
coil? Question text
d. 0.0833 siemens
Select one: What is the flux density
Feedback having a flux of 12,000
a. 2,000 kV maxwells through a
The correct answer is: 0.0833 perpendicular area of 6 cm
siemens b. 2 kV squared?
Question 42 c. 200 V Select one:
Incorrect d. 20 kV a. 72 gauss
Mark 0.00 out of 1.00 Feedback b. 2,000 gauss
Remove flag The correct answer is: 200 V c. 200 gauss
Question text Question 44 d. 72,000 gauss
A coil of resistor of 5 ohms Correct Feedback
and inductance 0.4 H is
connected to a 50 V d.c. Mark 1.00 out of 1.00 The correct answer is: 2,000
supply. The energy stored in gauss
the field is Flag question
Question 46
Select one: Question text
Correct
a. 80 joules A certain 50 micro-A meter
movement has a resistance of Mark 1.00 out of 1.00
Flag question Feedback emf induced is 9 V, then the
value of X is
Question text The correct answer is: 2
Select one:
A certain wire 20 ft long and Question 48
100 circular mil area has a a. 0.66 Wb-s^-2
resistance of 1.6 ohms. What Correct
is its resistivity? b. -1.5 Wb-s^-2
Mark 1.00 out of 1.00
Select one: c. -0.66 Wb-s^-2
Flag question
a. 2.2 ohm-CM/ft d. 1.5 Wb-s^-2
Question text
b. 8 ohm-CM/ft Feedback
The resistance of the field
c. 10.3 ohm-CM/ft winding of a DC machine is The correct answer is: -1.5
0.25 ohm at 25 degrees C. Wb-s^-2
d. 15.2 ohm-CM/ft When operating at full-load,
the temperature of the Question 50
Feedback winding is 75 degrees C. The
temperature coefficient of Incorrect
The correct answer is: 8 ohm- resistance of copper is
CM/ft Mark 0.00 out of 1.00
0.00427 per degree C at 0
Question 47 degrees C. Find the resistance Remove flag
of the field winding at full-
Correct load. Question text

Mark 1.00 out of 1.00 Select one: A 100 W, 110 V and 50 W,

110 V lamps are connected in
Flag question a. 0.298 ohm series across a 220 V DC
source. If the resistances of
Question text b. 0.315 ohm the two lamps are assumed to
c. 0.512 ohm remain constant, the voltage
Two metallic plates separated across the 100 W lamp is
by 1 cm are connected across _____ volt.
a 12 V battery. A certain d. 0.271 ohm
material is inserted Feedback Select one:
completely filling the space
between the plates and the The correct answer is: 0.298 a. 73.3 V
charge on each plate ohm
observed to double. What is b. 110 V
the dielectric constant of the Question 49
plastic material? c. 220 V
Incorrect
Select one: d. 146.7 V
Mark 0.00 out of 1.00
a. 6 Feedback
Remove flag
b. 2 The correct answer is: 73.3 V
Question text
c. 0.5 A flat circular coil having 50
A varying magnetic flux loops of wire on in has a
d. 4 linking a coil is given by phi diameter of 48 cm. What
= Xt^2. If at time t = 3 s, the current must flow in its wires
to produce a flux density of Question text The correct answer is: 8.28
0.005 Tesla at its center? ohms
Two similar electric charges
Select one: of 1 C each are placed 1 m Question 5
apart in air. Force of
a. 40.5 amperes repulsion between them Correct
would be nearly ____
b. 38.2 amperes Newton. Mark 1.00 out of 1.00

c. 45.5 amperes Select one: Flag question

d. 32.8 amperes a. 1 Question text

Feedback b. 8.854 x 10^-12 A 5-ohm resistor is connected

in parallel with a 10-ohm
The correct answer is: 38.2 c. 4*pi inductive reactance. The
amperes combination is then
d. 9 x 10^9 connected in series with a 4-
Question 2 ohm capacitive reactance.
Feedback The whole combination is
Incorrect
connected across a 100-volt,
The correct answer is: 9 x 60 Hz supply. How much is
Mark 0.00 out of 1.00 10^9 the total current drawn by the
Remove flag Question 4 circuit?
Question text Correct Select one:
Calculate the capacitance Mark 1.00 out of 1.00 a. 22.36 A
between two parallel plates
each of which is 100 cm^2 Flag question b. 19.89 A
and 2 mm apart in air.
Question text c. 23.16 A
Select one:
A series RLC circuit is d. 20.45 A
a. 0.443 uuF consisting of 20 ohms Feedback
resistor, 20 mH inductor, 100
b. 0.502 uF uF in series is connected to a The correct answer is: 22.36
c. 0.515 uF 100 V dc source. Find the A
additional resistance just to
d. 0.452 uF prevent the oscillation of the Question 6
resulting transient current
Feedback Correct
Select one:
The correct answer is: 0.443 Mark 1.00 out of 1.00
uuF a. 82.8 ohms
Flag question
Question 3 b. 282 ohms
Question text
Correct c. 26.2 ohms
The potential difference
Mark 1.00 out of 1.00 d. 8.28 ohms measured across a coil is 4.5
V, when it carries a direct
Flag question Feedback current of 9 A. The same coil
when carries an alternating
current of 9 A at 25 Hz, the Correct c. 3.33 H
potential difference is 24 V.
Find the power when it is Mark 1.00 out of 1.00 d. 0.49 H
supplied by 50 V, 50 Hz
supply. Flag question Feedback

Select one: Question text The correct answer is: 1.43 H

a. 54 W The electric energy required Question 10

to raise the temperature of
b. 63 W water in a pool is 1000 kWh. Correct
If the heat losses are 25%, the
c. 30 W heating energy required will Mark 1.00 out of 1.00
be ____. Flag question
d. 45 W
Select one: Question text
Feedback
a. 1111 kWh A plate capacitor is made up
The correct answer is: 45 W
b. 1750 kWh of 501 sheet of aluminum 25
Question 7 cm x 30 cm with a dielectric
c. 1333 kWh of paraffin paper 0.0015 cm
Correct thick. What is the capacitance
d. 1266 kWh in microfarads of the
Mark 1.00 out of 1.00 condenser (K for paraffin
Feedback paper is 2.3)?
Flag question
The correct answer is: 1333 Select one:
Question text kWh
a. 75
A galvanometer with a 20- Question 9
ohm coil resistance has a full- b. 35
scale deflection current of 10 Incorrect
mA. If a 0.02 ohm is placed c. 50
across the meter to increase Mark 0.00 out of 1.00
its capacity, what is the d. 25
approximate new full scale Remove flag
current of the meter? Feedback
Question text
Select one: The correct answer is: 25
Two coils of inductance 6 &
a. 10.11 A 4 Henries are connected in Question 11
parallel such that its
b. 10.01 A coefficient of coupling is Correct
41% with mutual inductance
c. 11.01 A opposes the self-inductance. Mark 1.00 out of 1.00
What is the total inductance Flag question
d. 10.10 A of the combination?
Feedback Question text
Select one:
The correct answer is: 10.01 A 1% d Arsonval meter
a. 0.94 H movement has coil and
A
b. 1.43 H swamping resistance adding
Question 8 to 200 ohms. The full-scale
voltage is 50 mV. Determine Question 13 d. 12pi x 10^-7 H/m
the shunt resistance required
producing 1 A full scale Correct Feedback
current meter.
Mark 1.00 out of 1.00 The correct answer is: 4pi x
Select one: 10^-7 H/m
Flag question
a. 52.02 milli-ohms Question 15
Question text
b. 50.01 milli-ohms Correct
A dc motor 10 hp, 230 volts
c. 49.22 milli-ohms has 0.85 efficiency. The Mark 1.00 out of 1.00
allowable voltage drop is
d. 48.74 milli-ohms 10% of input voltage. Find Flag question
the area of wire in circular
Feedback mil if the length is 150 ft. and Question text
resistivity of copper is 10.4 Find the voltage drop
The correct answer is: 50.01 ohm-cmil per ft.
milli-ohms developed across D Arsonval
Select one: meter movement having an
Question 12 internal resistance of 1 kilo-
a. 2588 ohms and full current of 150
Incorrect micro amperes.
b. 3088
Mark 0.00 out of 1.00 Select one:
c. 6176
Flag question a. 150 mV
d. 5176
Question text b. 150 V
Feedback
To test the accuracy of a c. 150 micro V
kilowatt-hour meter an The correct answer is: 5176
electrician used a wattmeter. d. 150 kV
He found out that the meter Question 14
makes 5 revolutions in 18 Feedback
seconds. The meter constant Incorrect
is 3.2. What is the percentage The correct answer is: 150 V
error if the wattmeter reading Mark 0.00 out of 1.00
Question 16
is 3368? Remove flag
Correct
Select one: Question text
Mark 1.00 out of 1.00
a. 8% slower Knowing that the absolute
permittivity of air is 8.854 x Flag question
b. 8% faster
10^-12 F/m, determine the
absolute permeability of air. Question text
c. 5% faster
Select one: A 6 H coil whose resistance
d. 5% slower is 12 ohms is connected in
Feedback a. 3pi x 10^-7 H/m series with a 24 ohms resistor
and to a 144 V battery and a
The correct answer is: 5% b. 2pi x 10^-7 H/m switch. The switch is closed
slower at t = 0. Determine the time
c. 4pi x 10^-7 H/m
constant and the steady state Correct Feedback
current of the circuit.
Mark 1.00 out of 1.00 The correct answer is:
Select one: 5*(permittivity of free space)
Flag question
a. 0.66 sec, 3 A Question 20
Question text
b. 0.36 sec, 12 A Incorrect
The maximum value of a sine
c. 0.50 sec, 6 A wave AC voltage which will Mark 0.00 out of 1.00
produce heat in a resistor at
d. 0.45 sec, 4 A the same average rate as 115 Remove flag
V of direct current is ____.
Feedback Question text
Select one:
The correct answer is: 0.50 A 100,000-ohm voltmeter is
sec, 6 A a. 230 V used in measuring the
insulation resistance of a
Question 17 b. 81.3 V motor. When connected in
series with the insulation
Incorrect c. 162.6 V across a 250-Volt line, the
Mark 0.00 out of 1.00 instrument reads 1 Volt.
d. 115 V What is the insulation
Flag question Feedback resistance of the motor?

Question text The correct answer is: 162.6 Select one:

V a. 25.1 Mega-ohms
A non-magnetic ring having a
mean diameter of 30 cm the Question 19
cross-section area is 4 sq. cm b. 29.4 Mega-ohms
and uniformly wound with Correct c. 18.7 Mega-ohms
two conductors A and B over
one another. A has 90 turns Mark 1.00 out of 1.00 d. 24.9 Mega-ohms
and B has 240 turns.
Calculate the first principle of Flag question Feedback
mutual inductance between Question text
the cores. The correct answer is: 25.1
If relative permittivity of Mega-ohms
Select one: mica is 5, its absolute Question 21
a. 11.52 permittivity is
Correct
b. 11.00 Select one:
Mark 1.00 out of 1.00
c. 10.55 a. 5*(permittivity of free
space) Flag question
d. 10.62
b. (permittivity of free Question text
Feedback space)/5
How many circular mils does
The correct answer is: 10.62 c. 5/(permittivity of free a round copper rod of 0.25
space) inch diameter have?
Question 18
d. 8.854 x 10^-12 Select one:
a. 196,000 radius, its capacitance to Flag question
infinity is
b. 62,500 Question text
Select one:
c. 1,963,500 Four 3 pCoul spheres are in
a. 55 uF corners of square q 1 cm on
d. 49,000 sides. Find the force in
b. 55 F Newton?
Feedback
c. 55 pF Select one:
The correct answer is: 62,500
d. 55 nF a. 15.5 x 10^(-10)
Question 22
Feedback b. 4.05 x 10^(-10)
Correct
The correct answer is: 55 pF c. 8.11 x 10^(-10)
Mark 1.00 out of 1.00
Question 24 d. 20.25 x 10^(-10)
Flag question
Correct Feedback
Question text
Mark 1.00 out of 1.00 The correct answer is: 15.5 x
If two identical 3 A, 4 ohms 10^(-10)
Norton equivalent circuits are Flag question
connected in parallel with Question 26
like polarity to like, the Question text
combined Norton equivalent Correct
circuit is A capacitor of 2 microfarad
with an initial charge q0 is Mark 1.00 out of 1.00
Select one: connected across the
terminals of a 10 ohm resistor Flag question
a. 6 A, 4 ohms and the switch is closed at t =
0. Find q0 (micro-coulomb) Question text
b. 6 A, 8 ohms if the transient power in the
resistor is known to be pR = In a parallel RLC resonant
c. 6 A, 2 ohms 360*e^(-10^-5*t) circuit R = 10 k ohms, C =
0.47 uF, the bandwidth will
d. 3 A, 2 ohms Select one: be.
Feedback a. 2100 Select one:
The correct answer is: 6 A, 8 b. 120 a. 212.76 rad/sec
ohms
c. 102 b. 100 rad/sec
Question 23
d. 1200 c. 2.12 x 10^10 rad/sec
Correct
Feedback d. none of the above
Mark 1.00 out of 1.00
The correct answer is: 120 Feedback
Flag question
Question 25 The correct answer is: 212.76
Question text rad/sec
Correct
If a body is considered as a Question 27
conducting sphere of 0.5 m Mark 1.00 out of 1.00
Correct The correct answer is: 33.33 c. 3.2 x 10^6 N/C

Mark 1.00 out of 1.00 Question 29 d. 2.8 x 10^6 N/C

Flag question Incorrect Feedback

Question text Mark 0.00 out of 1.00 The correct answer is: 3.0 x
10^5 N/C
Assuming an ideal capacitor, Flag question
with no leakage, what is the Question 31
capacitive reactance of 10 Question text
microfarad capacitance of Correct
DC (0 Hz)? A voltmeter with an internal
resistance of 5000 ohms is Mark 1.00 out of 1.00
Select one: calibrated to read 10 volts at
full-scale. How much series Flag question
a. 16000 ohms resistance is needed in order
to measure 150 volts at full Question text
b. 0 ohms scale? A single-phase three wire, 60
c. infinite capacitive Select one: Hz, 220 V, watthour meter
reactance has a disc constant of 1.2.
a. 78 kilo-ohms Determine the energy
d. 1,000,000 ohms recorder by the meter after
b. 70 kilo-ohms 18,000 revolutions of the
Feedback disc.
c. 75 kilo-ohms
The correct answer is: infinite Select one:
capacitive reactance d. 72 kilo-ohms
a. 21.6 kW-hr
Question 28 Feedback
b. 27.6 kW-hr
Correct The correct answer is: 70
kilo-ohms c. 25.4 kW-hr
Mark 1.00 out of 1.00
Question 30 d. 20.5 kW-hr
Flag question
Correct Feedback
Question text
Mark 1.00 out of 1.00 The correct answer is: 21.6
A galvanometer has a kW-hr
resistance of 300 ohms. What Remove flag
is the ohmic resistance to Question 32
make it read one is to ten? Question text
Correct
Select one: Calculate the magnitude of
the electric field at a point Mark 1.00 out of 1.00
a. 10 that is 30 cm from a point
charge Q = -3.2 x 10^-6 C. Flag question
b. 33.33
Select one: Question text
c. 30
a. 2.4 x 10^5 N/C Three (3) 10-uF capacitors
d. 100 are connected in series. What
b. 3.0 x 10^5 N/C is the total capacitance?
Feedback
Select one: Two coils of inductances 4 H Question 36
and 6 H are connected in
a. 3.33 uF parallel such that their mutual Incorrect
inductance is 3 H assists the
b. 60 uF self-inductance. The total Mark 0.00 out of 1.00

c. 30 uF inductance of the Remove flag

combination is ____.
d. 6.66 uF Question text
Select one:
Feedback Two similar coils have a
a. 3.75 H coupling coefficient of 0.25
The correct answer is: 3.33 and a mutual inductance of
uF b. 0.94 H
0.9 H. The self-inductance of
c. 2.06 H each coil is ____ Henry.
Question 33
d. 8.25 H Select one:
Correct
Feedback a. 0.2
Mark 1.00 out of 1.00
The correct answer is: 3.75 H b. 0.6
Flag question
Question 35 c. 0.36
Question text
Incorrect d. 0.4
A small single-phase, 240 V
induction motor is tested in Mark 0.00 out of 1.00 Feedback
parallel with 160 ohms
resistor. The motor takes 2 Remove flag The correct answer is: 0.6
amperes and the total current
is 3 amperes. What is the Question text Question 37
power of the whole circuit?
The total inductance of two Correct
Select one: coils, A and B when
connected in series aiding is Mark 1.00 out of 1.00
a. 360 W 0.5 H and 0.2 H when Flag question
connected in series opposing.
b. 800 W Coil A when isolated from Question text
c. 580 W coil B has a self-inductance
of 0.2 H. Calculate the self- Three capacitors of 20, 10
d. 220 W inductance of coil B. and 15 uF respectively are
connected in series across a
Feedback Select one: 100-V supply. Find the
voltage across the 10 uF
The correct answer is: 800 W a. 0.15 H capacitor.
Question 34 b. 0.16 H Select one:
Correct c. 0.20 H a. 46.15 V
Mark 1.00 out of 1.00 d. 0.12 H b. 42.38 V
Flag question Feedback c. 38.25 V
Question text The correct answer is: 0.15 H d. 54.52 V
Feedback b. 2.88 x 10^-3 J Select one:

The correct answer is: 46.15 c. 1.44 x 10^-3 J a. 12 siemens

V
d. 1.07 x 10^-3 J b. 0.0521 siemens
Question 38
Feedback c. 6 siemens
Incorrect
The correct answer is: 1.44 x d. 0.0833 siemens
Mark 0.00 out of 1.00 10^-3 J
Feedback
Flag question Question 40
The correct answer is: 0.0833
Question text Correct siemens

Two straight parallel wires 2 Mark 1.00 out of 1.00 Question 42

m long and 3 mm apart
carries a current of 8.0 A in Flag question Correct
opposite direction. Calculate
the force between these Question text Mark 1.00 out of 1.00
conductors. A 240-V, 25 Hz sinusoidal Flag question
Select one: generator is connected to a 20
ohms resistor. Determine the Question text
a. 8.53 x 10^-3 N instantaneous current when
elapsed time is 0.01 second. A three-phase 230-V circuit
b. 8.75 x 10^-3 N serves two single-phase
Select one: loads, A and B. Load A is an
c. 8.33 x 10^-3 N induction motor rated 8 hp,
a. 16.30 A 230 V, 0.70 pf, 0.90
d. 8.25 x 10^-3 N efficiency, which is
b. 15.43 A connected across lines a and
Feedback b. Load B draws 5 kW at 1.0
c. 12.00 A pf and is connected across
The correct answer is: 8.53 x lines b and c. Assume a
10^-3 N d. 16.97 A
sequence of a-b-c, solve for
Question 39 Feedback the total power factor of the
load.
Correct The correct answer is: 16.97
A Select one:
Mark 1.00 out of 1.00
Question 41 a. 0.864
Flag question
Correct b. 0.886
Question text
Mark 1.00 out of 1.00 c. 0.704
A 20 uF capacitor is charged
by a 12-V battery. What is Flag question d. 0.907
the stored energy in the Feedback
capacitor? Question text

The resistance of 120 meters The correct answer is: 0.864

Select one:
of wire is 12 ohms. What is
its conductance? Question 43
a. 2.88 x 10^-2 J
Correct a. 35% The two circuits have the
following values: R1 = 5
Mark 1.00 out of 1.00 b. 79% ohms X1 = 3 ohms inductive,
R2 = 7 ohms and X2 = 4
Flag question c. 85% ohms capacitive. If the
Question text d. 47% terminal voltage is 120 volts,
what is the total current?
A circuit whose resistance is Feedback
20 ohms and inductance of Select one:
10 H has a steady state The correct answer is: 47%
a. 35.5
voltage of 100 volts suddenly
applied to it. For the instant Question 45
b. 20.6
of 0.50 second after the Correct
voltage is applied, determine c. 30.8
the total power input to the Mark 1.00 out of 1.00
circuit. d. 14.9
Flag question
Select one: Feedback
Question text
a. 500 watts The correct answer is: 30.8
To roughly check his kWh
b. 116 watts meter an electrician hook-up Question 47
a wattmeter, he switched on Correct
c. 200 watts the load, he counted 5 rev in
d. 316 watts 18 sec, the meter constant is Mark 1.00 out of 1.00
3.2. The wattmeter reads 368
Feedback Watts. What is the error of Flag question
the meter?
The correct answer is: 316 Question text
watts Select one:
A one-meter rod of 2-cm
Question 44 a. 5% faster diameter is drawn until its
resistance is 100 times the
Incorrect b. 5% slower initial resistance. Its length
afterwards is?
Mark 0.00 out of 1.00 c. 8% slower
Select one:
Flag question d. 8% faster
a. 5 m
Question text Feedback
b. 10 m
Two coils A and B are The correct answer is: 8%
connected in series such that slower c. 12.5 m
the total inductances are 1 H
and 0.4 H depending on the Question 46 d. 100 m
direction of current in the Correct
coils. Calculate the coupling Feedback
factor between the coils if the Mark 1.00 out of 1.00 The correct answer is: 10 m
self-inductance of coil B is
0.5 H. Flag question Question 48
Select one: Question text Incorrect
Mark 0.00 out of 1.00 d. 862

Flag question Feedback

Question text The correct answer is: 682

The relative permeability of a Question 50

certain silicon steel is 4500.
A certain magnetic loop Correct
consists of a silicon steel of
10 cm square, 20 cm long Mark 1.00 out of 1.00
and an air gap of 1/4 cm, Flag question
what is the reluctance of the
magnetic circuit? Question text
Select one: The stator of a 440 V, 50 HP
shunt motor is tested at 75
a. 6.44 x 10^-4 degrees C for its insulation
b. 2.54 x 10^-2 resistance between terminals
connected together and the
c. 6.44 x 10^-3 ground frame. When a 50,000
ohm voltmeter is connected
d. 2.54 x 10^-3 in series with a 600 V DC
source, the meter indicates
Feedback 125 V. Calculate the
insulation resistance.
The correct answer is: 2.54 x
10^-2 Select one:
Question 49 a. 170 kilo-ohms
Correct b. 180 kilo-ohms
Mark 1.00 out of 1.00 c. 190 kilo-ohms
Flag question d. 200 kilo-ohms
Question text Feedback
The power factor of a load on The correct answer is: 190
a 120 volt, 60 Hz source is kilo-ohms
raised from 0.707 to 0.866
lagging by connecting a 53
micro-farad capacitor across
the load. What is the true
power of the load in watts?

Select one:

a. 286

b. 268

c. 682