meno%8 Connecting Wayne DART Pumps me > Support» Setup Pumps > Connecting Wayne BART Pp CONNECTING WAYNE DART PUMPS Wayne DART protocol originates in Furope, with pumps manufactured in Sweden and Germany, but is used widely as one of Dresser Wayne's main protocols along with US Current Loop. Wayne Pignone and Nuovo Pignone ‘Nuovo Pignone was an allan company with many pump models and their own unique protocol and hardware layer, However, their newer pumps supported Wayne DART asa connection option. In 2004 Dresser-Wayne purchased NP and the resulting company is now known as Dresser Wayne Pignone. DART is their main protocol for new models, Other Brands Using DART Protocol AAs one of the most widely used European protocols, DART is also supported by ether manufacturers besides Wayne and Wayne Pignone, with varying levels of accuracy. For example: Europump, Protocol Variations “Tis protocol has two main levels of feature support + Standard DART - orginal protacol used on older Wayne pump computers such as Duplex + Full DART - updated protocol which adds extra features electronic totals, pause+ resume instead of stop only, price level contra, and lights contro. Enabler supports these two feature levels va Pump Type, and aso allows features o be turned on or off via advanced settings. ‘Asa rule of thumb, pumps manufactured sine about year 2000 wil likely support Full DART, those before may only hve standard DART. See our general \Wayne information for pump models and background, Wayne Dart pumps manufactured in China use the Full art protocol but require the advanced setting ETOTALS=1 to succesfully retrieve the electronic totals, ‘Note: Reliable communication with DART pumps requires Enabler Card Firmware version of a least v2.85 build 07. Ifyou have an version, authorisation and other important communications may be less reliable. hntpshww.integration.co.nziprvdocs/FAG-WayneDART.ntmn 18meno%8 Connecting Wayne DART Pumps What will | need? “The physical connection for DART pumps i RS48S, “To connect these pumps you will quire: 1, FOM Part: FDMog2 Passive © Jumper 12 set to RSAB5 position ot FSA 2, No power supply is required for this FOM, fo ole oo ofc of -pooho oho) 3, D825 female connector with backshel cable clamp, ete 4, Multstrand cable with 3 oF more cores to sult dstance between PC and FDM - maximum 15 metres (45 feed). For example, CATS or CATE cable, Note that 2 cores is not enough as aground is needed as well 5. Tools wie stripper soldering iron, solder, 3mm flat blade screwdriver. 6.Cabling to pumps if necessary. You can use the same shielded multi-core, mul-strand cable as above hntpshww.integration.co.nziprvdocs/FAG-WayneDART.ntmn 218meno%8 Connecting Wayne DART Pumps Physical Connection Connecting FDM to Enabler Select which Enabler por (1-3) you will use. Strip the ends ofthe cable, Solder one end tothe port pins on the DB2S socket. Leave the other ends bare to connect to the FDM: Make sure you connect the FDM RS-485 ground to the Enabler D825 ground pins. This provides protection to the Enabler cara against surges, such as nearby lightning strikes (if you have an old revision 1 FDM, there sno ground pin} °° cou a Upto 10M ‘once completed tthe clamp tothe cables entering the D825, and close the backshell onthe 0828. Connecting FDM to Pump Connect the two wires fom the pumps) to any ofthe pump connectors on the FOM, and set the switch tothe On (Down) postion, AA soe IF all pamps are connected correctly the voltage from A to B should be between TV and AV DC. fits negative, you may have the A and 8 from The Enabler connected back to font. hntpshww.integration.co.nziprvdocs/FAG-WayneDART.ntmn 318meno%8 Connecting Wayne DART Pumps Configuring the Pump ‘See our main Wayne FAQ for more information. For pumps with communication options set the baud rate to 9600 and the protocol to Standard or Full DART. For pumps using the iGEM computer, make sure parameter F23.02is set to around 10 or higher fit is zero, no running totals will be sent by the pump and delivery progress can't be monitored. It should not be a small number or the pump may accasionally go offline between Enabler poll. “The DART protocol allows addressing of up to 32 purnps, however The Enabler only supports Polling Addresses from 1 to 16, Make sure you set the address in the pump to a value inthe range 1-16 (0x50 to OxSF). Each af the communications ports on the Enabler PCI card can communicate with 16 logis! pumps; to cannect more than 16 logical pumps, you nead to use two (or more) ports. Some older Wayne DART pumps need to be turned off and back on before they stat communicating. hntpshww.integration.co.nziprvdocs/FAG-WayneDART.ntmn 418meno%8 Connecting Wayne DART Pumps Enabler Configuration Using the Web Appiations > Configuration + on the Pos page set the loop type to Wayne DART ‘+ On the Pumps page foreach pump: © Set the pump type to "Wayne DART” for standard DART behaviour, ‘Wayne DART Full” for the full DART feature set, or one ofthe Nuovo Pignone types as discussed below. © Select the appropriate display format. © Set the polling aciress to match the pump adress Notes: 1. After the ports have been configured, you will need to restart the Enabler Pump server toload the correct pump drives, Nuove Pignone Pumps in DART Made “The NP emulation of DART isnot identical toa Wayne pump. For corect operation with multi-hose Nuovo Pignone Pumps, you should install the latest Pump Driver Update, and select one ofthe Nuovo Pignane DART pump types Pump Type Description Nuova Pignone DART 1 - Disables swtching off pump (via EnbPumpx PumplightsOn property). Pumps that do net support “allowed hoses” command, 0 uses minarvastion to authorisation sequence, Nuove Pignone DART 2. - Disables witching off purnp (va EnbPumpX PurmplightsOn property Pumps do support “allowed hoses” command. = Pumps that support authorisation limits. 2A DART 2A dlspenser brands emulating Nuovo Pignone DART 1 For CNG (NGW dispensers you should set the Pump Type to "Wayne DART” or Wayne DART Fll hntpshww.integration.co.nziprvdocs/FAG-WayneDART.ntmn 58meno%8 Advanced Settings Connecting Wayne DART Pumps See also: Using Advanced Settings. For Wayne DART pumps the following advanced settings are supported: ‘Advanced Setting Description Optional Behaviours RESETONCLEAR=1 Defauk 0 This setting will cause the purnp dlsply to be cleared when the delivery is eleaed (sold or stacked), instead of waiting nti the next delivery starts. This is not supported by all DART computers. (On {GEM pumps this behaviours determined by » Pump Configuration Setting, \We recommend you check for local regulations regarding the dsplay ofthe last fuel sale - in some countries the last sale ‘must remain onthe display until another delivery is started. ‘Nozzle Lift Conditions By defaut, the Enabler will nt show the nozzle ited (aling) until the previous delvery has been cleared (stacked or sole). This is because, for malt- hose pumps, cortectly determining which nozaleis out may require clearing the pump displays. ‘You make the Enabler report the nozzle lifted without clearing the delivery, in two alternative ways, as below, Which one is suitable depends on what behaviour is acceptable fr the site, nd how the pump behaves, Defaul 0 RESETWITHCURRENT=1 Default 0 This seting causes Enabler to report the nozzle out while the previous delivery has not been cleared, without sending » Reset to the pum, + Good: The pump cisplay will not be cleared + Bad: On multichose pumps, the wrong hose may be reported This setting canbe used on any single hose pump without concern This setting causes Enabler to report the nozzle out while the previous delivery has not been cleared, by sending a Reset to the pump as soon asthe nozzles ited, + Good: The correct hase will be shown, + Bad: The pump dsplay may be cleared, Feature Control USEREMOTEUIMIT=1 Defaul 0 By default The Enabler sends mits to the cispenser and relies on itto stop, This works with most pumps Ina few cases ‘the pump may not support limits inthis case you can set this advanced setting to cause Enabler to monitor the delivery and stop it approximately atthe limit. hntpshww.integration.co.nziprvdocs/FAG-WayneDART.ntmn 68menor Connecting Wayne DART Pumps ETOTALS=x USERAUSE= CChnages the behavior ofthe Electronic Totals ‘Many DART pumps do not support Electronic Total. you enable electronic totals but the pump does nat support them, there willbe along pause afte each delivery while Enabler attempts to retrieve the totals For DART driver v3.5.3 and onwards: 8y default this setting is off) for Dart and on for Full Dart. In ase your Full DART pump does NOT correctly report the ‘otalzers, then please change your pump type to Standard DART and change this setting accordingly + With ETOTALS=1, both the volume and value ttalzeris requested, This is a diferent totaizer request to the Full DART pump type + With ETOTALS=2, only the volume totlizers requested ‘+ With ETOTALS=3, only the value totaizer ie requestec. For DART diver v3.6.1 and onwards: By default the ETOTALS value willbe determined by the pump type defauki(see table). This setting applies to all pump types and affects how/i the totals are requested. ETOTALS | Totalsrequested | Default for pump types _| Method ° Totalsnot requested Dart, NP Dar 1, NP Dart 2 1 Money, Volume i cp101 2 Volume only 2ndan oro 3 Money only I cp101 4 Money, Quantity Dart Full oe s Volume only ws 6 Money only a 7 Money, Volume Europump 101, comer [Note:The Chinese Wayne Dart Full pumps use the CDS totals method for something else so the ETOTALS=1 setting needs to be used, ‘Switches the pause resume feature on (1) oof (0). Ths feature defaults to on for Full DART and off fr Standard DART. Requires Driver v2.220 or newer. This refers to the numberof decimal digits used for translating Electronic Volume Totals, If this Advanced Setting snot set or is negative, the default values the number of decimal digits for rasaction volume minus 1 ‘Accepts decimal digit values of 0103 This refers tothe number of decimal digits used for translating Electronic Money Totals If this Advanced Setting isnot set or is negative, the default values the same asthe number of decimal digits for transaction money. ‘Accepts decimal digit values of 0 to 3 READNOZZLEINPRI Default Requires Driver v2232 or newer. Set this if you want the driver to read the hose price on delivery completion or once nozzle is returned, "Normally, OART pumps retum the price once the nozzles ited and the pump is authorized, But for some pumps, the price retuned on this scenario i the price of the previous delivery IGNOREMON' Defaul 0 Set this ifyou want the diver to return a delivery or volume only pumps ~ pumps which return zero delivery smoney/value Under normal situations, Enabler expects both the delivery volume and delivery value to be non-zero (deliveries with zo volume of zero value are ignored and not logged), hntpshwww.integration.co.nziprvdocs/FAQ-WayneDART.ntmn 78meno%8 Connecting Wayne DART Pumps Troubleshooting Symptom | Possible Cause(s) Prices Not Ithe price ie not abe tobe set but the pump is otherwise working then you may need to add additional nozzles. DART computers set will nt accept prices unless there is a price for every nozzle, even nezales that are net physically connected. Unfortunately the protocol dees net support any way to detect how many nozzles the pump is expecting, nor does the pump report iit did nat accept the prices, so you may need to experiment wit several adltional hoses, For example, with an X2003-6 computer ty upto 6 hoses. You may be able to tell by examining the pump's internal configuration how many nozzles itis expecting No running Make sure parameter F23.02is sett around 10 or higher, its zero, no running totals wil be sent by the pump and delivery Totalson progress can't be monitored. It shoul not be a small number, oF the pump may occasionally go ofine between Enabler pol {GEM pump Nozzle Lift is Examine and test the advanced settings for Nozze Lift Conditions a discussed above, rot Shown Long Pause You have configured Enabler to a5k for Electronic Totals but the pump does not supper them. Aller Each Delivery No Electronic Ensure you have the latest Enabler Pump Driver Update, then try the Wayne DART Full pump type, or the ETOTALS=1 advanced Towlsare setting. Retieves ‘Many older DART pumps do not have E-Totals and this cannot be remedied in Enabler. Contact the pum distributor to seein ‘upgrade is possible - we believe this should be possible for atleast modern iGEM-based pumps. You may also be able to switch the ‘pump (and Enabler) to Wayne US Current Loop protocol For Teosis pump computers ‘Teosis pump firmware protocol version 2.8 onwards is required. Te request the electronic totals: Install DART pump diver version 3.4.2 or higher, set Enabler with protocol = "Wayne Dar and ETOTALS=1 in advanced setting, No Electronic Teesis pump frmaware pratocol version 28 onwards is required. Te request the electronic totals: Totals are Install DART pump driver version 3.4.2 or higher, set Enabler with protocol = "Wayne Dart and ETOTALS=1 in advanced setting Retrieved for Teosis pump computers Delivery Lost | Install the latest Enabler Pump Driver Update ‘on Power or ‘comms Failure ‘Authorisation Occasionally Does Not Work Check thatthe Enabler Card Firmware version isa least v2.77 build 1. In that version we fixed an occasional reliability issue hntpshww.integration.co.nziprvdocs/FAG-WayneDART.ntmn 88