Scribd Logo
Upload

Welcome to Scribd!

  • 21 views

    Para-Flex Spacer Couplings: Installation

    Uploaded by

    Jon

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Para-Flex Spacer Couplings: Installation

    Uploaded by

    Jon
    21 views2 pages

    Original Title

    MN4039

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    21 views2 pages

    Para-Flex Spacer Couplings: Installation

    Uploaded by

    Jon

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 2

    PARA-FLEX® Spacer Couplings

    These instructions must be read thoroughly before installing or operating this product.

    INSTALLATION: 4. Holding the replacement flexible element upright with the


    split open and up, slip each flange into the element. Place
    1. Install hubs on shaft per instructions packaged with this assembly on one end and work the element down on
    bushings. Shaft ends must not project beyond hub ends. the flange seats, using a small mallet if necessary, until
    2. Place shafts into position. If shaft end float is to occur, the split of the element is closed. Holding the split closed,
    locate the shafts at the mid-position of the end float.* tighten (by half turns) two screws in the top flange which
    Dimension “A”, see drawing, should be the same as the are directly opposite the split in the element. Using both
    figure stamped on the end of the flange after the coupling hands, knead the tire pulling it toward the split. Hold split
    number. closed and tighten (by half turns) next two screws farthest
    3. Check shaft angular misalignment by measuring dimension from split. Repeat this procedure on all remaining clamp
    “A” at four places 90º apart. Adjust the equipment until the screws. Retighten (by half turns) all clamp ring screws
    four measurements do not vary more than value “B” per the repeatedly, stopping when metal-to-metal contact is felt
    table. Check the parallel offset by laying a straight edge upon bottoming of the clamp ring to the flange. With the
    across the O.D. of shaft hubs in four places 90º apart. clamp ring thus bottomed to the flange and the rubber
    The gap between the flange and straight edge should not element thus compressed to its limitation, retighten each
    exceed 1/32”. To realize maximum coupling life, align the screw with a torque wrench to the torque specified in the
    coupling as accurately as possible at initial installation. table for clamp ring screws. Turn the assembly over and
    4. Check the torque on the clamp ring screws per the table. using the procedure specified above, tighten the screws in
    Tighten if necessary. Compress the center assembly (using the remaining flange.
    “C” clamps if necessary) and slip between the hubs until 5. Replace center assembly per Step 4 of Installation.
    the pilots engage. Install hub screws and tighten with a
    torque wrench to the torque specified in the table for hub Wrench Torque (Pound-Inches)
    screws.
    Coupling Size Clamp Ring Screws Hub Screws “B”
    PS40 130 130 1/64
    FLEXIBLE ELEMENT REPLACEMENT:
    PS50 130 180 1/64
    1. Remove hub screws. Compress the center assembly (using PS60 240 180 1/64
    “C” clamps if necessary) and remove from place.
    PS70 290 180 1/64
    2. Loosen all clamp ring screws. Grasp one end of flexible
    element at the split and peel off of flanges. PS80 290 300 1/64
    3. Check to see that only 2 or 3 threads of each clamp ring PS90 480 300 1/32
    screw are engaged. PS100 480 300 1/32
    PS110 480 300 1/32
    WARNING: Because of the possible danger to persons(s)
    or property from accidents which may result from the PS120 1080 720 1/32
    improper use of products, it is important that correct PS140 1080 720 1/32
    procedures be followed. Products must be used in
    accordance with the engineering information specified PS160 2160 1296 1/16
    in the catalog. Proper installation, maintenance and PS200 2160 1296 1/16
    operation procedures must be observed. The instructions
    in the instruction manuals must be followed. Inspections
    should be made as necessary to assure safe operation If replacing clamp ring screws and washers, use only SAE
    under prevailing conditions. Proper guards and other Grade 8 screws and hardened washers.
    suitable safety devices or procedures as may be desirable * If limited end float is required or sleeve bearings are used,
    or as may be specified in safety codes should be provided, consult DODGE product support.
    and are neither provided by Baldor Electric Company nor
    are the responsibility of Baldor Electric Company. This unit
    and its associated equipment must be installed, adjusted
    and maintained by qualified personnel who are familiar
    with the construction and operation of all equipment in
    the system and the potential hazards involved. When risk
    to persons or property may be involved, a failsafe device
    must be an integral part of the driven equipment beyond
    the speed reducer output shaft.
    1
    P.O. Box 2400, Fort Smith, AR 72902-2400 U.S.A., Ph: (1) 479.646.4711, Fax (1) 479.648.5792, International Fax (1) 479.648.5895
    Dodge Product Support
    6040 Ponders Court, Greenville, SC 29615-4617 U.S.A., Ph: (1) 864.297.4800, Fax: (1) 864.281.2433
    www.baldor.com
    © Baldor Electric Company All Rights Reserved. Printed in USA.
    MN4039 4/11 Printshop 10000
    *4039-0411*

    You might also like