Screw pump

AFI horizontal

Utilization
For pumping heating oils, fuels (including low-sulfur ship
fuel and marine diesel), lubrication oils, hydraulic oils or
other lubricating liquids. The pumped liquids may not
contain any abrasive components nor chemically attack the
pump material.
Main field of application
ALLFUEL pumps are employed as transfer, booster and
burner operation pumps in oil fired systems, as transfer
pumps in (marine) fuel systems, as feeder and filling
pumps in tank systems and as lube-oil pumps in virtually all
areas of industry. They are also used in oil hydraulic
systems of all types.
Design
Single pump/motor assembly in compact design; vertical
and horizontal configuration without integrated filter.
Abbreviation

 Theoretical capacity Q[l/min] at 1.450 1/min and

AFI vertikal 46-degree pitch angle.
 D = antifriction bearing outside.
 Unheated, uncooled mechanical shaft seal.
 Version with electric heating of mechanical seal available at
additional charge.
 V = vertical; H = horizontal.
 F = counter flange; A = adapter flange.

GB/2016.06 – Ident-No. 488130 1

Structural design Filter and twin units
Internal bearing, three screw, self priming screw pump. A separate system filter is essential when pumping oil with
Together with the rotor housing, bearing, mechanical seal, these no-filter AFI pumps. However, these pumps are also
and pump cover, the hardened and polished screws form available with an integrated radial screen filter (AFI-F
an insert unit that can be exchanged quickly and easily. version) for protection against contamination. Filter mesh
The drive spindle is hydraulically balanced. A special screw size 0,4 mm. Refer to document number 488083 for more
design absorbs the axial thrust of the idler screws. It is information. Twin units (version AFI-T) are provided when
hydraulically driven. Only the torque resulting from liquid a reserve pump is required. Refer to document number
friction is transferred to the thread flanks. The thread flanks 488083 for more information.
are therefore virtually free of loads and are not subject to Heating
wear. The pumped liquid lubricates all sliding parts and can If heating is required, these pumps can be delivered with
be categorized as full fluid friction. The radial and axial electric heating cartridges for the mechanical seal chamber
bearing of the drive screw is provided by an outer-lying (subject to additional cost)
groove ball bearing that is separated from the liquid. A
mechanical seal is used as the shaft seal. Pump size Connection Heating cartridge
A return bore connects the seal chamber and the suction for output
area to each other. As a result, only suction pressure acts (Pressure side)
on the shaft seal, regardless of discharge pressure. When 10 230 V 200 W
a complete pump/motor assembly is delivered, a pump 20 230 V 200 W
bracket connects the pump to the drive motor.
40 230 V 300 W
Three sizes and various screw pitches ensure fine
gradation of the entire flow rate range. Heating capacity is dimensioned so that when outlet
The ALLFUEL family is designed with an insert unit temperature is 20 °C heating time of 60 minutes will be
consisting of a pre-assembled unit with liner, spindle set, adequate for highly viscous liquids. When temperatures
mechanical seal, bearing and cover. are lower, a corresponding longer heat-up time will be
In case of changing operation condition which request a required. Heating is not designed to achieve noticeable
different material combination or in case of replacement higher liquid temperatures during operation. To avoid
this insert unit can be implemented quickly and easily potential damage to the bearing, do not exceed the
without dismantling the pump housing from the pipe works permitted temperature of the pumped liquid.
(process design). Leaks
The insert unit fits into all existing ALLFUEL pump- Formation of a lubricating film between the sliding surfaces
housings as well as into pump-housings of the predecessor is the most important factor in the functionality of a
SPF-family (and all correlated derivates). mechanical seal. This film is formed by the liquid being
sealed. This "standard leak" of a few ml/h is essential for
maintaining lubrication of the sliding surfaces. Absence or
inadequate formation of a lubricating film is a common
cause of damage.
When pumping liquids with low volatility, such as HFO, the
user must therefore expect increasing deposits on the
atmosphere side as time passes. As a result, it is
physically not possible to achieve a 100% seal with a
mechanical seal. If this is not acceptable, the magnetically-
coupled version of ALLFUEL will be the right choice. Refer
to document number .. for more information.
Flanges and connections
Functionality Feed and pressure ports as counter flange based on SAE
Specially shaped thread flanks cause the three spindles to (SAE J518C, hole pattern 3000 PSI).
form sealed chambers; rotation of the spindles then causes Connections at present: E7 Venting of pump
the contents of the chambers to move continuously in the H7 Heating cartridge
axial direction from the pump's suction side to its pressure M1, M2, Pressure gauge.
side. Despite rotation of the spindles, no turbulence results. Temperature gauge
The uniform chamber volumes eliminate crushing forces. Shaft seal
Performance data The shaft is sealed with a maintenance-free, unbalanced
Capacity  Q up to 112 l/min mechanical seal.
Suction pressure ps up to 6 bar Part name Material design
Discharge pressure  pd up to 40 bar Rotating ring silicon carbide
Liquid temperature  t up to 150 ° C Counter ring silicon carbide
Viscosity range ν 1 up to 750 mm²/s Seal ring peroxide cross-linked FKM
Spring CrNiMo steel
 at n = 2.900 1/min and ν = 750 mm²/s. Metal parts CrNiMo steel
 Refer to the individual reference curves for the achievable
Noise level and pulsation
pump pressure in relation to viscosity and rotational speed.
Pressure specifications are applicable only to nearly static The design and operation of the screw pump enable a very
pressure loads. Please inquire about dynamically alternating low noise level and virtually pulsation-free pumping.
pressure loads.
Consultation required if temperatures higher.

2 GB/2016.06 – Ident-No. 488130

Overload protection and main dimensions according to DIN EN 50347. Motors
A pressure-relief valve is integrated into each pump as a configured for 50 Hz may also be operated in 60 Hz
means of overload protection. Its standard trigger pressure networks.
is set to approximately 10% above the working pressure. Power is transferred over an elastic coupling. Additional
Please make sure your order specifies if a different trigger radial forces may not act on the drive spindle.
pressure is desired.
Explosion protection
Installation The pump fulfills the requirements according to EU
To avoid air trapped inside the pump, the pump may not be explosion-protection directive 2014/34/EC (ATEX 100a) for
installed with the flanges pointing down. devices in device class II, category 2 G. Classification into
When installed vertically, a “motor down” arrangement is temperature classes according to
not permitted for safety reasons. In addition, the vent screw DIN EN 13463-1 depends on the temperature of the
(160) may not point down. pumped liquid. Refer to the proposal or order
Drive documentation for the maximum permissible liquid
A motor bracket facilitates connection of a wide variety of temperature for the respective temperature classes.
electric motors or other drive units. Note: When operating the pump in category 2, suitable
The following motor versions are normally provided with measures must be provided to prevent impermissible
delivery of complete pump/motor assemblies: warming of the pump surfaces in the event of disturbance.
Surface-cooled three-phase squirrel-cage motors, IMV 1
design type, IP 55 protection class according to IEC
standard, insulation class F utilized according to B, output

Materials
Denomination Material design
W196  W196 E  W198  W198 E 
Pump casing EN-GJS-400-15 EN-GJS-400-15
Casing insert Alu Alu EN-GJL-250 tenifer. EN-GJL-250 tenifer.
Pump cover end drive EN-GJS-400-15 EN-GJS-400-15 EN-GJS-400-15 EN-GJS-400-15
Drive screw
16MnCrS5 16MnCrS5 16MnCrS5 PVD 16MnCrS5 PVD
Idler screw
 Recommended material for all liquids incl. HFO up to 40 bar (except: Low Sulphur MGO / MDO)
 Size 40 : Recommended material for critical liquids up to 40 bar (e.g. HFO, Low Sulphur MGO / MDO)
 
 
 

NPSH – values [m]

NPSH req. for the pump without filter
AFI Speed 1/min
950 / 1.140 1.450 / 1.750 2.900 3.400
Kinematic viscosity mm²/s
3-40 150 750 3-40 150 750 3-40 150 750 3-40 150 750
10-28 2,5 2,8 3,2 2,5 2,9 3,6 2,5 2,9 4,2 2,6 3,1 4,3
10-38 2,5 2,8 3,6 2,5 2,9 3,9 2,5 3,1 4,6 2,6 3,3 5,1
10-46 2,5 2,9 3,9 2,5 3,0 4,2 2,6 3,3 5,1 2,8 3,5 6,6
10-56 2,5 2,9 4,3 2,5 3,1 4,5 2,8 3,7 7,3 3,1 4,1 7,0
20-38 2,5 2,9 3,9 2,5 2,9 4,1 2,5 3,2 5,0 2,7 3,5 5,6
20-46 2,5 2,9 4,2 2,5 3,1 4,4 2,7 3,5 6,2 3,0 3,9 7,0
20-56 2,5 3,0 4,5 2,5 3,3 5,1 3,2 4,1 7,2 3,6 4,6 9,1
40-38 2,5 2,9 3,8 2,5 3,1 4,3 2,7 3,5 5,6 2,9 3,8 6,3
40-46 2,5 3,0 4,2 2,6 3,3 4,8 3,0 4,0 6,8 3,4 4,4 7,8
40-54 2,5 3,2 4,8 2,7 3,6 5,4 3,6 4,7 8,2 4,2 5,5 9,7

GB/2016.06 – Ident-No. 488130 3

Performance table (Specifications for n =1.450 1/min and 3.500 1/min)
Frequenzy 50 Hz 60 Hz
Speed 1.450 min-1 3.500 min-1
Pump size Discharge Kinematic viscosity mm²/s Kinematic viscosity mm²/s
pressure 3 12 150 750 3 12 150 750
Q P Q P Q P Q P Q P Q P Q P Q P
Allfuel bar l/min kW l/min kW l/min kW l/min kW l/min kW l/min kW l/min kW l/min kW
5 4,51 0,15 4,85 0,15 5,10 0,25 5,16 0,47 11,86 0,52 12,21 0,52 12,45 0,89 12,51 1,72
10 3,96 0,20 4,58 0,20 5,02 0,30 5,12 0,52 11,31 0,62 11,93 0,62 12,38 1,00 12,47 1,82
15 3,44 0,24 4,32 0,24 4,95 0,34 5,09 0,56 10,80 0,73 11,67 0,73 12,30 1,10 12,44 1,93
20 2,96 0,28 4,08 0,28 4,88 0,38 5,06 0,60 10,31 0,83 11,43 0,83 12,23 1,21 12,41 2,03
10-28
25 2,49 0,33 3,84 0,33 4,82 0,43 5,03 0,65 9,84 0,94 11,20 0,94 12,17 1,31 12,38 2,14
30 2,03 0,37 3,62 0,37 4,75 0,47 5,00 0,69 9,39 1,04 10,97 1,04 12,10 1,42 12,35 2,24
35 1,59 0,41 3,40 0,41 4,69 0,51 4,97 0,73 8,94 1,14 10,75 1,14 12,04 1,52 12,32 2,34
40 1,16 0,46 3,18 0,46 4,63 0,56 4,94 0,78 8,51 1,25 10,53 1,25 11,98 1,62 12,30 2,45
5 6,89 0,18 7,34 0,18 7,67 0,28 7,74 0,50 17,92 0,57 18,37 0,57 18,70 0,94 18,77 1,77
10 6,16 0,24 6,98 0,24 7,57 0,34 7,70 0,56 17,19 0,73 18,01 0,73 18,60 1,10 18,72 1,93
15 5,48 0,31 6,64 0,31 7,47 0,41 7,65 0,63 16,51 0,88 17,67 0,88 18,50 1,26 18,68 2,08
20 4,84 0,37 6,32 0,37 7,38 0,47 7,61 0,69 15,87 1,04 17,35 1,04 18,41 1,42 18,64 2,24
10-38
25 4,23 0,44 6,01 0,44 7,29 0,54 7,57 0,76 15,25 1,20 17,04 1,20 18,32 1,57 18,60 2,40
30 3,63 0,50 5,71 0,50 7,21 0,60 7,54 0,82 14,65 1,35 16,74 1,35 18,24 1,73 18,56 2,55
35 3,04 0,57 5,42 0,57 7,13 0,67 7,50 0,89 14,07 1,51 16,45 1,51 18,15 1,89 18,53 2,71
40 2,47 0,63 5,14 0,63 7,05 0,73 7,46 0,95 13,50 1,67 16,16 1,67 18,07 2,04 18,49 2,87
5 9,30 0,20 9,84 0,20 10,24 0,30 10,32 0,52 23,99 0,62 24,53 0,62 24,93 1,00 25,01 1,82
10 8,42 0,28 9,41 0,28 10,11 0,38 10,27 0,60 23,11 0,83 24,10 0,83 24,80 1,21 24,95 2,03
15 7,62 0,37 9,00 0,37 10,00 0,47 10,21 0,69 22,30 1,04 23,69 1,04 24,69 1,41 24,90 2,24
20 6,85 0,46 8,62 0,46 9,89 0,56 10,17 0,78 21,54 1,25 23,31 1,25 24,58 1,62 24,86 2,45
10-46
25 6,11 0,54 8,25 0,54 9,78 0,64 10,12 0,86 20,80 1,46 22,94 1,46 24,47 1,83 24,81 2,66
30 5,39 0,63 7,89 0,63 9,68 0,73 10,07 0,95 20,08 1,67 22,58 1,67 24,37 2,04 24,76 2,87
35 4,69 0,72 7,54 0,72 9,58 0,82 10,03 1,04 19,38 1,88 22,23 1,88 24,27 2,25 24,72 3,08
40 - - 7,20 0,80 9,49 0,90 9,99 1,12 18,69 2,08 21,89 2,08 24,18 2,46 24,68 3,28
5 12,07 0,23 13,31 0,23 14,20 0,33 14,39 0,55 32,64 0,71 33,88 0,71 34,77 1,08 34,96 1,91
10 10,87 0,35 12,71 0,35 14,03 0,45 14,32 0,67 31,44 1,00 33,28 1,00 34,60 1,37 34,89 2,20
15 9,92 0,47 12,23 0,47 13,89 0,57 14,26 0,79 30,49 1,29 32,80 1,29 34,47 1,67 34,83 2,49
20 9,09 0,60 11,82 0,60 13,78 0,70 14,20 0,92 29,66 1,58 32,39 1,58 34,35 1,96 34,78 2,78
10-56
25 8,35 0,72 11,45 0,72 13,67 0,82 14,16 1,04 28,92 1,88 32,02 1,88 34,24 2,25 34,73 3,08
30 - - 11,11 0,84 13,58 0,94 14,12 1,16 28,24 2,17 31,68 2,17 34,15 2,54 34,69 3,37
35 - - 10,80 0,96 13,49 1,06 14,08 1,28 27,61 2,46 31,37 2,46 34,06 2,84 34,65 3,66
40 - - 10,50 1,08 13,40 1,18 14,04 1,40 27,02 2,75 31,07 2,75 33,97 3,13 34,61 3,95
5 14,31 0,27 14,87 0,27 15,27 0,40 15,36 0,67 36,12 0,84 36,68 0,84 37,09 1,32 37,17 2,34
10 13,41 0,40 14,42 0,40 15,14 0,53 15,30 0,80 35,22 1,15 36,23 1,15 36,96 1,63 37,12 2,65
15 12,58 0,53 14,00 0,53 15,03 0,66 15,25 0,93 34,39 1,46 35,82 1,46 36,84 1,94 37,06 2,96
20 11,78 0,65 13,61 0,65 14,91 0,78 15,20 1,05 33,60 1,77 35,42 1,77 36,73 2,25 37,01 3,27
20-38
25 11,02 0,78 13,23 0,78 14,81 0,91 15,15 1,18 32,84 2,08 35,04 2,08 36,62 2,56 36,97 3,58
30 10,28 0,91 12,86 0,91 14,70 1,04 15,10 1,31 32,10 2,39 34,67 2,39 36,52 2,87 36,92 3,89
35 9,56 1,04 12,50 1,04 14,60 1,17 15,06 1,44 31,38 2,70 34,31 2,70 36,42 3,19 36,87 4,20
40 8,86 1,17 12,14 1,17 14,50 1,30 15,01 1,57 30,67 3,01 33,96 3,01 36,32 3,50 36,83 4,51
5 18,71 0,31 19,50 0,31 20,07 0,44 20,20 0,71 47,41 0,93 48,20 0,93 48,77 1,42 48,90 2,43
10 17,43 0,48 18,86 0,48 19,89 0,61 20,12 0,88 46,13 1,34 47,56 1,34 48,59 1,83 48,82 2,84
15 16,25 0,65 18,27 0,65 19,73 0,78 20,04 1,05 44,95 1,75 46,97 1,75 48,43 2,24 48,74 3,25
20 15,13 0,82 17,71 0,82 19,57 0,95 19,97 1,22 43,83 2,16 46,41 2,16 48,27 2,65 48,67 3,66
20-46
25 14,04 0,99 17,17 0,99 19,42 1,12 19,90 1,39 42,74 2,57 45,87 2,57 48,12 3,05 48,60 4,07
30 13,00 1,16 16,65 1,16 19,27 1,29 19,84 1,56 41,70 2,98 45,35 2,98 47,97 3,46 48,54 4,48
35 11,97 1,32 16,14 1,32 19,12 1,45 19,77 1,72 40,67 3,38 44,84 3,38 47,82 3,87 48,47 4,88
40 - - 15,64 1,49 18,98 1,62 19,71 1,89 39,67 3,79 44,34 3,79 47,68 4,28 48,41 5,29
5 23,75 0,38 26,09 0,38 27,76 0,51 28,12 0,78 63,93 1,10 66,27 1,10 67,94 1,58 68,30 2,60
10 21,49 0,61 24,96 0,61 27,44 0,74 27,98 1,01 61,67 1,67 65,14 1,67 67,62 2,16 68,16 3,17
15 19,69 0,85 24,05 0,85 27,19 0,98 27,87 1,25 59,87 2,24 64,23 2,24 67,37 2,73 68,05 3,74
20 18,13 1,09 23,28 1,09 26,97 1,22 27,77 1,49 58,31 2,81 63,46 2,81 67,15 3,30 67,95 4,31
20-56
25 16,74 1,32 22,58 1,32 26,77 1,45 27,68 1,72 56,92 3,38 62,76 3,38 66,95 3,87 67,86 4,88
30 - - 21,94 1,56 26,59 1,69 27,60 1,96 55,64 3,96 62,12 3,96 66,77 4,44 67,78 5,46
35 - - 21,34 1,80 26,42 1,93 27,52 2,20 54,45 4,53 61,52 4,53 66,60 5,01 67,70 6,03
40 - - 20,78 2,03 26,26 2,16 27,45 2,43 53,33 5,10 60,96 5,10 66,44 5,59 67,63 6,60
5 28,45 0,41 30,19 0,41 31,44 0,54 31,71 0,81 73,59 1,35 75,33 1,35 76,58 2,03 76,85 3,38
10 25,65 0,67 28,79 0,67 31,04 0,80 31,53 1,07 70,79 2,00 73,93 2,00 76,18 2,67 76,68 4,02
15 23,07 0,94 27,50 0,94 30,68 1,07 31,37 1,34 68,21 2,64 72,64 2,64 75,82 3,31 76,51 4,66
20 20,61 1,20 26,27 1,20 30,33 1,33 31,21 1,60 65,75 3,28 71,41 3,28 75,47 3,96 76,36 5,31
40-38
25 18,25 1,47 25,09 1,47 30,00 1,60 31,06 1,87 63,39 3,92 70,23 3,92 75,14 4,60 76,21 5,95
30 15,95 1,74 23,94 1,74 29,67 1,87 30,92 2,14 61,10 4,57 69,08 4,57 74,81 5,24 76,06 6,59
35 13,72 2,00 22,82 2,00 29,35 2,13 30,78 2,40 58,86 5,21 67,97 5,21 74,50 5,88 75,92 7,23
40 11,53 2,27 21,73 2,27 29,04 2,40 30,64 2,67 56,67 5,85 66,87 5,85 74,19 6,53 75,78 7,88
5 38,28 0,54 40,42 0,54 41,96 0,72 42,30 1,08 98,46 1,57 100,61 1,57 102,15 2,24 102,48 3,59
10 34,83 0,90 38,70 0,90 41,48 1,08 42,08 1,44 95,02 2,43 98,89 2,43 101,66 3,10 102,27 4,45
15 31,65 1,25 37,11 1,25 41,03 1,43 41,88 1,79 91,84 3,28 97,30 3,28 101,21 3,96 102,06 5,31
20 28,63 1,61 35,60 1,61 40,60 1,79 41,69 2,15 88,81 4,14 95,78 4,14 100,78 4,81 101,87 6,16
40-46
25 25,71 1,96 34,14 1,96 40,19 2,14 41,50 2,50 85,90 4,99 94,33 4,99 100,37 5,67 101,69 7,02
30 22,89 2,32 32,73 2,32 39,79 2,50 41,33 2,86 83,07 5,85 92,91 5,85 99,97 6,53 101,51 7,88
35 20,13 2,67 31,35 2,67 39,40 2,85 41,15 3,21 80,32 6,71 91,54 6,71 99,58 7,38 101,34 8,73
40 - - 30,00 3,03 39,02 3,21 40,98 3,57 77,62 7,56 90,19 7,56 99,20 8,24 101,17 9,59
5 48,83 0,67 53,02 0,67 56,02 0,85 56,68 1,21 129,71 1,86 133,90 1,86 136,91 2,54 137,56 3,89
10 44,76 1,14 50,99 1,14 55,45 1,32 56,42 1,68 125,65 3,01 131,87 3,01 136,33 3,69 137,31 5,04
15 41,53 1,62 49,37 1,62 54,99 1,80 56,22 2,16 122,41 4,16 130,25 4,16 135,88 4,84 137,10 6,19
20 38,73 2,10 47,97 2,10 54,60 2,28 56,04 2,64 119,62 5,32 128,86 5,32 135,48 5,99 136,92 7,34
40-54
25 36,23 2,57 46,72 2,57 54,24 2,75 55,88 3,11 117,11 6,47 127,60 6,47 135,13 7,14 136,77 8,49
30 - - 45,57 3,05 53,92 3,23 55,74 3,59 114,81 7,62 126,45 7,62 134,80 8,29 136,62 9,64
35 - - 44,50 3,53 53,62 3,71 55,60 4,07 112,68 8,77 125,38 8,77 134,50 9,44 136,49 10,79
40 - - 43,50 4,00 53,33 4,18 55,48 4,54 110,67 9,92 124,38 9,92 134,21 10,59 136,36 11,94

Note: Refer to the proposal or order documentation for exact performance data for individual operating points.

4 GB/2016.06 – Ident-No. 488130

Assembly AFI

Idler screw Insert casing Motor

Pump cover
Drive screw (drive side) Coupling

Pressure relief valve

Shaft seal Mounting foot

Motor bracket

Heating

Pump casing

Pump foot

GB/2016.06 – Ident-No. 488130 5

Main dimensions AFI
AFI horizontal configuration

n
A

K
J dd ds
L

hd
hs
j

S
g

T
k

v1

m
C
B
H7
M2 M1
V

Id Is
v2

Ds
Fs
N
M
w

Gd Gs
Dd

Fd

E7
a
x

Shaft end

P
R
Q

key acc.to
DIN 6885

6 GB/2016.06 – Ident-No. 488130

Main dimensions AFI
AFI vertical configuration

n
M
N E

K
J
L
E7 V
C

H7

dd
Gd

A
Dd
Id

hd
M2 hs
B

Fd
c
Is
Gs

ds

M1
t

Ds
Fs S
T
e2
f2 Pump foot

y1
y2
e1
f1

GB/2016.06 – Ident-No. 488130 7

Main dimensions AFI
AFI size Pump dimensions
A B C E J K L M N P Q R S T V
10 247 110 55,5 82,55 -0,05 19,4 21,6 13 130 106 16 14 j6 5 60 132 11
20 293,5 125 15 65 145
77,5 101,6 -0,05 27 26 175 146 21,5 19 j6 6 14
40 342,5 135 17 80 164

AFI size Unit dimensions

Motor size
a c e1 e2 f1 f2 g j k m
80 162 209 452
90S 89,5 140
10 150,5 200 160 181 218 496
90L
100L 111,5 202 223 160 546
90S
151,5 181 218 140 558
90L
20 100L 163 220 180 202 223 564
128,5 160
112M 120 84 227 238 571
132S 141,5 266 278 170 683
90L 151,5 181 218 140 558
100L 202 223 564
128,5 160
112M 227 238 571
40 132S 212 240 200
141,5 266 278 170 683
132M
150/
160M 320 314 235 862
415 

Unit dimensions
AFI size Motor size
n s t v1 v2 w x y1 y2 z
80 602
90S 200 160
10 646
90L
100L 696 250 200
100 14
90S
721 200 160
90L
20 100L 727
8 250 200
112M 734 8 14 7 38
132S 846 120 300 250 14,5
90L 770 200 160
100L 776 100
250 200 14
112M 783
40
132S
895 120 300 250
132M 14,5
160M 1074 18 305 350 300 18 

Connections Dimensions in mm,

AFI size Venting Heating Cartridge Pressure gauge Direction of rotation:
Clockwise as seen from
E7 H7 M1/M2 the drive side.
10 G 1/8
M8x1 M12x1
20 and 40 G 1/4  SAE J518C, hole
pattern 3.000 PSI.
 Dimensions are
AFI size Connection dimensions reference only and may
SAE-suction flange  SAE-pressure flange  deviate depending on
motor manufacturer.
Inch Ds Fs Gs Is ds hs Inch Dd Fd Gd Id dd hd  Foot mounted design
10 ¾ 22 47,63 22,23 28 96 ¾ 22 47,63 22,23 28 96 on pump size 40 for
4 x M10 motor size 160M with 4
20 1 25 52,37 26,19 35 103 1 4 x M10 103
25 52,37 26,19 35 screws, see ALL2CAD
40 1 ¼ 32 58,72 30,18 4 x M12 43 121 1 118 for dimensions.

8 GB/2016.06 – Ident-No. 488130

Benefits
 Economical use of space  Flawless start-up
The installed pump requires little The vent screw ensures the best possible
space. venting of the mechanical seal chamber each
time the pump is started, even when installed
vertically.

 Reliable process stability  Outstanding reliability

Specially-shaped thread flanks The conical valve provides
produce virtually pulsation-free, permanent protection against
low-noise pumping action. impermissibly high
pressures.

 Impressive service life

Hydrodynamic axial thrust com-
pensation minimizes loads on the
screws and extends service life.

 Flawless pump starting

Optional heating of the casing
ensure that the pump starts
without issue even when the
ambient temperature is low.

 Extraordinary flexibility  Versatile and adaptable

A wide range of available The ability to install the pump
materials makes it possible to horizontally or vertically lets the
adapt to special operating operator adapt to even small
conditions and various liquids. spaces.

GB/2016.06 – Ident-No. 488130 9

Subject to technical alteration!

ALLWEILER GmbH
Postfach 1140  78301 Radolfzell
Allweilerstr. 1  78315 Radolfzell
Germany
Tel. +49 (0)7732-86-0
Fax +49 (0)7732-86-436
E-mail: [email protected]
Internet: http://www.allweiler.com
GB/2016.06 – Ident-No. 488130