Scribd
Upload
80 views6 pages

Assignment 2

The document provides instructions for revising a parking lot design assignment to meet ADA requirements. Students are to: 1) Calculate the required number of parking spaces using the building's interior square footage and local codes. Draw the interior space in AutoCAD to calculate the area. 2) Determine the required number of ADA parking spaces using provided tables and guidelines. Draw ADA parking spaces and aisles per regulations. 3) Email the revised AutoCAD drawing and get feedback on interior square footage calculations. 4) Refer to a grading rubric for assignment standards. Additional ADA drawing reference material is provided on pages 2-6.

Uploaded by

LEO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
80 views6 pages

Assignment 2

The document provides instructions for revising a parking lot design assignment to meet ADA requirements. Students are to: 1) Calculate the required number of parking spaces using the building's interior square footage and local codes. Draw the interior space in AutoCAD to calculate the area. 2) Determine the required number of ADA parking spaces using provided tables and guidelines. Draw ADA parking spaces and aisles per regulations. 3) Email the revised AutoCAD drawing and get feedback on interior square footage calculations. 4) Refer to a grading rubric for assignment standards. Additional ADA drawing reference material is provided on pages 2-6.

Uploaded by

LEO
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

1

Assignment-2 “ADA Parking Lot Revisions”

Due: Progress drawings by Friday, November 5th, 7:00 PM

1) From the websites below, using the “Class 1.Office” space, note the parking spaces for every 1000 square feet of
building space. Figure out how much interior square footage you have inside the building. From within AutoCAD, create
a new layer called AREA and use the AutoCAD AREA command and draw an interior polyline around all the interior of
the exterior wall until it closes. After you do this, type Area in the command line and select “O” for Object and select
your new polyline. Then, on the command line, it will show you the area square footage. Once you find this, email me
the number and I will tell you if you are close within 100 square feet or not and then go back and design the ADA
parking & regular parking spaces in the building area shown on Assignment-1 and revise the parking from Assignment-1
to match the required parking of Assignment-2.

City of Houston Codes:

Section 26-Parking Requirements dependent on building type:

https://library.municode.com/tx/houston/codes/code_of_ordinances/178617?nodeId=COOR_CH26PA_ARTVIIIOREPALO
_DIV2REPASP_S26-492PASPCETYOC

2) Visit this website to figure out how many ADA parking spaces required for this project and how to draw ADA parking
spaces and aisles at:

https://www.tdlr.texas.gov/ab/abtas.htm

See “Table 208.2 Parking Spaces” and it will show you the amount of ADA parking spaces required based on your total
number of parking spaces.

See Chapter 4: Accessible Routes, 406 Curb Ramps to draw a curb cut (curb ramp).

See Chapter 5: 502 Parking Spaces. See 502.2 Vehicle Spaces and 502.3 Access Aisle

3) Email the revised assignment as “Your initials”_Bicycle Shop-A2.dwg to: [email protected]

4) See “Grading Rubric” for point subtraction for all assignments in the *START HERE* folder. This explains how you
will be graded on all these assignments.

**See pages 2-6 below for additional ADA drawing info:


2

Continued
3
4

Continued

Continued
5

Continued
6

You might also like