The GE90 - An Introduction

GE-90 TURBOFAN ENGINE (CUT-AWAY VIEW)

Built by General Electric in conjunction with SNECMA of France, IHI of Japan and
FiatAvio of Italy, and first commissioned by the British Airways for its new fleet of
Boeing 777s recently (September 1995), it is the most powerful commercial aircraft
engine today. Certified at a Take-Off Thrust of 380 kN (85,000 lb.), only two engines
suffice for a huge aircraft like the 777 with a seating capacity of 375 (weight approx.
230 tonnes). A derivative of the GE/NASA Energy Efficient Engine (E3) program, it is
also the most fuel efficient, silent and environment friendly engine of today. In
addition to the highest thrust to be offered, the GE90 is expected to provide airlines
with a 5-6% improvement in fuel burn, lower noise pollution, and NOX emissions
33% lower than today’s high bypass ratio engines.

This seminar attempts at highlighting the various aspects of the engine by

presenting a brief insight into its features.

1
COMPARISON
HIGH THRUST CLASS TURBOFAN ENGINES (> 200 kN) (modified
after [2])
GE-90 CF6-50C2 CF6-80C2
Company General Electric (USA) General Electric (USA) General Electric (USA)
In use since September 1995 1978 October 1985
First flew on Airbus A-340 & B-777 KC-10 (Military) A-300/310, 747/767
Description High Bypass TF Two-Shaft High BPR TF Two-Shaft High BPR TF
Weight (Dry) --- 3960 kg 4144 kg
Overall Length 4775 mm 4394 mm 4087 mm
Intake/Fan Diameter 3124 mm 2195 mm 2362 mm
Pressure Ratio 39.3 29.13 30.4
Bypass Ratio 8.4 5.7 5.05
Thrust at TO 388.8 kN 233.5 kN 276 kN
Thrust during Cruise 70 kN 50.3 kN 50.4 kN
S.F.C. (SLS) 8.30 mg/N-s 10.51 mg/N-s 9.32 mg/N-s
Air mass flow rate 1350 kg/s 591 kg/s 802 kg/s
Presence of FADEC* Yes No Yes
Other information 33 % lower NOx TET of LPT is 1144 K. Lower fuel burn (s.f.c.)
emission . Less noise than other engines, long
than other TFs in its life, high reliability.
class (due to low fan
tip speed)

RB-211-524G/H Trent-882 JT-9D-7R4

Company Rolls Royce (UK) Rolls Royce (UK) Pratt & Whitney (USA)
In use since February 1990 August 1994 (Cert.) February 1969 (first)
First flew on 747-400 & 767-300 Boeing 777 Boeing 747/767, A310
Description Three-Shaft Axial TF Three Shaft TF Twin-Spool TF
Weight (Dry) 4479 kg 5447 kg 4029 kg
Overall Length 3175 mm 4369 mm 3371 mm
Intake/Fan Diameter 2192 mm 2794 mm 2463 mm
Pressure Ratio 33 33+ 22
Bypass Ratio 4.3 4.3+ 5
Thrust at TO 269.4 kN 366.1 kN 202.3 kN
Thrust during Cruise 52.1 kN 72.2 kN 176.3 kN
S.F.C. 15.95 mg/N-s (cruise) 15.66 mg/N-s (cruise) 10.06 mg/N-s
Air mass flow rate 728 kg/s 728+ kg/s 687 kg/s
FADEC (Y/N) No Yes No
Other information Most powerful
conventional a/c engine
in contract (till Sept. ‘95)
in the world (Trent 772)

*FADEC - Fully Automated Digital Engine Control

• gives improved fuel consumption.
• better engine control and reduces pilot work load by interacting with aircraft computers.
• lower aircraft operating costs.

LOW THRUST CLASS TURBOFAN ENGINES (< 200 kN) (modified

after [2])

2
 CFM56-5C2 JT-8D-17R V 2500-A1
Company CFM International Pratt & Whitney (USA) Intl. Aero Engines (USA)
(France) & GE (USA)
In use since Late 1992 February 1970 July 1988
First flew on Airbus A-340 Boeing 727/737 & DC-9 Airbus A-320
Description Two Shaft Subsonic TF Axial Flow Twin-Spool Twin Spool Subsonic TF
TF
Weight (Dry) 2492 kg (Bare Engine) 1585 kg 2242 kg (Bare Engine)
3856 kg (approx.) 3311 kg (with
powerplant)
Overall Length 2616 mm 3137 mm 3200 mm
Intake/Fan Diameter 1836 mm 1080 mm 1600 mm
Pressure Ratio 37.4 17.3 29.4
Bypass Ratio 6.6 1.00 5.42
Thrust at TO 138.8 kN 72.9 kN 111.25 kN
Thrust during 30.78 kN 18.9 kN 21.6 kN
Cruise
S.F.C. 16.06 mg/N-s 23.37 mg/N-s 16.29 mg/N-s
Air mass flow rate 466 kg/s 148 kg/s 355 kg/s
FADEC (Y/N) Yes No Yes
Other information

3
GE-90 TURBOFAN CYCLE ANALYSIS
Following are the results of a simple high bypass ratio turbofan engine cycle analysis
carried with the help of a computer program. The theory of the analysis can be found
in [3]. A more extensive and accurate analysis can be obtained from [4]. The
available data on the GE90 engine was merely limited to its take-off thrust, bypass
ratio (BPR) and overall pressure ratio (OPR). The rest of the data is tentative and is
assumed on the basis of other similar GE engines (like CF6-80C2 and CFM56) with
the appropriate improvements considered.

ENGINE DATA
Intake efficiency = 0.980
Fan polytropic efficiency = 0.930
Compressor polytropic efficiency = 0.910
Turbine polytropic efficiency = 0.930
Isentropic nozzle efficiency = 0.950
Mechanical efficiency = 0.990
Combustion pressure loss (ratio) = 0.050
Fuel combustion efficiency = 0.990

Area of hot nozzle = 1.0111 m2

Area of cold nozzle = 3.5935 m2

Design Point Off-Design Point

(Cruise) (Take-off)
Height (km) 10.668 0.000
Mach No. 0.850 0.000
RAMPR 1.590 1.000
FPR 1.650 1.580
LPCPR 1.140 1.100
HPCPR 21.500 23.000
OPR 40.440 39.970
Pa (bars) 0.239 1.014
Ta (K) 218.820 288.160
Ca (m/s) 252.000 0.000
BPR 8.100 8.400
TIT (K) 1380.000 1592.000
ma (kg/s) 576.000 1350.000
THRUST (kN) 69.200 375.300
mf (kg/s) 1.079 2.968
SFC (mg/N-s) 15.600 7.910
Sp. Thrust (N-s/kg) 120.100 278.100

The computed value of the cruise thrust is found to be in close agreement with the
thrust required by the Boeing 777 aircraft with two GE90 engines which is around
65-70 kN per engine.

4
GRAPHS FOR DESIGN POINT OPERATIONS (CRUISE)

Thrust & SFC vs FPR

70 17.00

69 16.75

68 16.50
Thrust (kN)

67 16.25
THRUST
66 16.00 SFC

65 15.75

64 15.50
1.40
1.43
1.46
1.49
1.52
1.55
1.58
1.61
1.64
1.67
1.70
1.73
1.76
1.79
FPR

Thrust & SFC vs OPR

78 18.0

76 17.5

74 17.0
Thrust (kN)

72 16.5 THRUST
SFC
70 16.0

68 15.5

66 15.0
20 22 24 26 28 30 32 34 36 38 40 42 44 46
OPR

5
Thrust & SFC vs BPR

110.0 19.0

102.5 18.5

95.0 18.0

87.5 17.5
Thrust (kN)

80.0 17.0
THRUST
72.5 16.5 SFC

65.0 16.0

57.5 15.5

50.0 15.0
4.0
4.4
4.8
5.2
5.6
6.0
6.4
6.8
7.2
7.6
8.0
8.4
8.8
9.2
9.6
BPR

Thrust & SFC vs TIT

100 21

90 20

80 19
Thrust (kN)

70 18 THRUST
SFC
60 17

50 16

40 15
1300 1350 1400 1450 1500 1550 1600 1650 1700 1750 1800
TIT (K)

6
CERTIFICATION ([1] and [2])
MILESTONES

Date Event
November 1992 First core test
March 1993 First engine to test with 377.8 kN thrust
April 1993 First engine to test with 468.5 kN thrust
December 1993 First GE90 flying testbed on Boeing 747
November 1994 GE90 certifies at 388.8 kN thrust
December 1994 First Boeing 777 flight test
August 1995 Boeing 777/GE90 aircraft certification
September 1995 Boeing 777/GE90 entry into service

GE90 Ground and Flight Testing -

With FAA certification of the GE90, GE Aircraft Engines brought to close one
of the most extensive ground and flight test programs ever undertaken by an
engine manufacturer.
GE announced the development of the GE90 in January 1990. In November
1992, the first full-scale engine core went to test; the first full engine followed
in March of 1993. Since that time, GE and its revenue sharing participants
have run a total of 13 development engines which have verified the engine’s
inherent design benefits. Overall, the engines have logged more than 5,000
hours, including 228 flight hours on GE’s modified Boeing 747 flying test bed.
GE90 endurance engines completed more than 14,000 cycles and
demonstrated excellent section durability. Seven engines have operated at
more than 100,000 lb. (444.5 kN) of thrust, with one achieving a record-
breaking 110,000 lb. (489 kN) of thrust. In fact, GE90 development engines
have sustained thrust levels in excess of 100,000 lb. (444.5 kN) for more than
65 hours.
As part of the required certification testing, the GE90 successfully completed
both the 2.5 and 8 lb. (1.13 and 3.63 kg) bird ingestion tests on the engine’s
composite blades.
In October 94, four 2.5 lb. birds were ingested with the engine running at
speeds required to produce 85,000 lb. (377.8 kN) of thrust at takeoff on a hot
day. There was no thrust loss and the engine responded to all throttle
commands during the required 20 minutes of operation following the
ingestion. All fan blades were in excellent condition and have continued to
run in other engine tests.
In mid-November 94, GE conducted the fan bladeout test with the FAA
present. The release blade was detonated at a fan speed of 2,485 rpm, 10
rpm over the target, with the engine generating more than 105,000 lb. (466.8
kN) of sea level static (SLS) corrected thrust. The engine mount system
performed as designed and the test demonstrated fan blade containment.
The ruggedness of the composite fan blade was successfully demonstrated,

7
and the observed trailing blade damage matched pre-test analysis, verifying
the inherent benefits of the composite blade design.
The GE90 flew for the first time in late 1993 installed on the 747 flying
testbed. Throughout the first phase of testing, the engine accumulated nearly
228 hours in 45 flights. The engine performed exceptionally well,
demonstrating performance levels that were better than specification and
provided pilots unrestricted throttle movement throughout the flight envelope.

WHY AN ALL-NEW ENGINE?

Requirement by Market
Historically, aircraft have grown in weight and thrust requirements. Today, the
market favors heavier and longer range aircraft with thrust growth built in.

Growth Chart 1 Growth Chart 2

The above growth charts show that trend favors GE90-powered large
widebody aircraft.

Positioned for the Airline’s Future

• Common engine for entire families of new, larger aircraft.
• New widebody aircraft demand 20-30% higher thrust than today’s engines.
• Aircraft historically require 20-30% additional thrust for increases in TOGW.

Modern cycle design has built-in total performance advantages

• 10% better SFC than today’s engines.
• High thrust growth with commonality.
• Low noise and emissions.

Reliability of Proven Technology incorporating “Lessons Learned”.

GE90 DESIGN
The GE90 is designed for :
• Thrust Growth.
• Engine commonality for the 777 Airplane Family.
• Fuel Efficiency.
• 180-Minute ETOPS (Extended Twin OPerationS).

8
• Low Emissions.
• Low Noise.
• Reduced Operating Cost.

Cycle Selected for significant fuel savings.

• Bypass ratio optimized.
• Overall pressure ratio optimized.
• Designed for lowest SFC and fuel burn.

Designs selected for maximum airline benefit.

• Designed and demonstrated technologies for high reliability.
• Builds on CF6 and CFM56 reliability.
• ETOPS approval.
• Operator developed maintenance procedures.
• Designed for low noise and low emissions.
• Designed for Lowest Operating Cost.

Engine Sized For Future Aircraft Requirements.

• Initial certification at 84,700 lb. (376.5 kN) thrust - February 1995
• First growth certification at 92,000 lb. (408.9 kN) thrust - May 1996.
• Potential to grow to 120,000 lb. (533.4 kN).

HIGH THRUST AND TEST EXPERIENCE

Summary
• Over 145 Hours at > 422.3 kN
• Over 95 Hours at > 435.6 kN
• Over 75 Hours at > 440.0 kN
• Over 65 Hours at > 444.5 kN
• 20 Hours of Continuous Running on 900-105/1A at > 444.5 kN

Note : Sea Level Static (SLS) Corrected Thrust Levels

Eight GE90 engines have operated at or above 445 kN of SLS Thrust.

Various tests carried out

• Fan Mapping.
• Booster Stress Survey.
• Overspeed Certification (490.3 kN).
• “Dress Rehearsal” for Triple Redline Block Test.
• 1.13 kg Bird Certification / Blade Out Certification.

9
THE ENGINE AND ITS COMPONENTS ([2])

GE-90 TURBOFAN ENGINE (CROSS-SECTIONAL VIEW)

The following are the main components of the engine -

1. Composite fan
2. Low Pressure Compressor (LPC) / Booster
3. High Pressure Compressor (HPC)
4. Dual Dome Combustor
5. High Pressure Turbine (HPT)
6. Low pressure Turbine (LPT)

10
COMPOSITE FAN

GE90 Fan Design

Fan Diagram

• 22 composite wide-chord blades and platforms.

• Large fan diameter for higher air mass flow.
• Fan geared - reduces fan tip speed thus producing less noise.
• Low tip speed and pressure ratio for quiet efficient operation.
• Lightweight tri-web disk for inspectibility and reduced weight.
• Hybrid (conical/elliptical) spinner for low core debris ingestion.
• Fan Pressure Ratio (FPR) about 1.60-1.65 (tentative).

GE90 Fan Blade

Fan Blade

• Wide Chord Composite Fan - high performance and low weight.

• Environmental resistance - GE90 fan material system displays equal
environmental resistance like those of current aircraft composites.

11
• GE90 fan composite material system demonstrated similar to those
currently in service.
• Laminated specimens fully exposed to aircraft fluids typically maintained 95
percent base properties.
• Actual blade fully protected by polyurethane coating.
• No exposure to ultraviolet radiation.

Composite Fan Development History

• GE90 Composite Blade Benefits from 25 Years of Development.
• Materials, manufacturing and computing advances have provided the
necessary technology.

12
COMPRESSOR

Compressor Diagram First Stage HPC blade

• Structure similar to successful CFM56.

• Compact engine construction.
• Rugged, low aspect ratio airfoils.
• Reduced part count.
• Reduced operating cost.
• Short LPC/booster - 3 stages.
• LPC Pressure Ratio (LPCPR) around 1.10-1.14 (tentative).
• Low LPT entry temperatures for thrust growth.
• 10 stage HPC with 23-to-1 Pressure Ratio (HPCPR).
• Scale-up of the NASA Energy Efficient Engine (E3) demonstrated
performance and operability in both test cell and flight test.

COMBUSTOR

• Dual dome annular combustor from successful advanced military

programs.
• Reduced NOX emission levels (as low as 10 ppm.).
• Reduced unburned hydrocarbon, carbon monoxide and smoke levels.
• Improved operability.
• Long-life liner construction.
• Dome aero-thermo tuned for power setting.
• Altitude re-light capability 30,000 ft (9.144 km) with margin.

13
TURBINE

Turbine Diagram HP Turbine Blade - Stages 1 & 2 resp.

• High Pressure Turbine incorporates proven design technology.

• 6-stage LPT and 2-stage HPT.
• Stiff, simply supported rotor system like CFM56 for dynamic stability.
• Boltless assembly airfoil and shroud cooling circuits modeled after
successful CF6-80 design.
• Introduces film-cooled technology from proven turbine experience.
• Multihole turbine cooling technology - better cooling effectiveness.
• Successful CF6-80 designs and passive clearance control system features.
• Stage 1 HPT blade casting with laser drilled cooling hole pattern (Material
N5).
• Stage 2 HPT blade with laser drilled cooling hole pattern (Material N5).
• Modular nozzle assemblies based on CFM56 and CF6-80 designs.

14
OTHER FEATURES ([2])

GE90 AND THE ENVIRONMENT

Reduced Emissions and Smoke
• Dual Dome Combustor.
• Reduced Noise.
• Low Fan Pressure Ratio and large aspect ratio low pressure turbine.
• Overall lower mission total fuel burn = Lower total mission pollutants.
• Higher thrust to core flow ratio.

GE90 Combustor Provides Improved Operability with Reduced Emission

Levels
• Double Annular Combustor.
• Pilot dome optimized for operability - main dome optimized for high power.
• Emissions reduction Based on 15 years of NASA and Advanced Military
Engine Development.
• Full-scale GE90 Testing.
• Exit temperature profiles meet design intent.
• Emission levels verified.

TRANSPORTABILITY
• Designed for Standard Engine Transport Methods.

GE90 Propulsor
• Smaller than the high bypass turbofans of today

GE90 Modular Design

• Allows replacement of propulsor only
• Separate Propulsor/Nozzle from Fan Stator Module
• Fan stator module remains at main base or with aircraft
• Removal and Replacement Time Estimated at Less than 6 Hours

15
FUTURE OF GE90 ([2])

THRUST GROWTH
GE90 components are sized for growth. If the market requires it, 110,000 lb.
(511 kN) of thrust could be produced by a GE90 with further investment. The
following are the ways General Electric intends to achieve the thrust
increment -

• 376.5 kN Fan
Certification Engine.
B777 “B” Market.

• 409 kN Fan
Improved LPT Materials.
Increased HPT Cooling and 1st Stage Blade TBC.
B777 “B” Market.
B777 Stretch.

• 422.3 - 435.6 kN Fan

Improved Turbomachinery.

• 466.8 kN Fan
Higher P/P Fan with Destaged Core.

• 511.2 + kN TF
Higher Speed and P/P Fan with Destaged Core.

16
CONCLUSION
It is seen that GE90 is indeed the most powerful and efficient commercial
transport engine of the 90’s. It also has ample scope for thrust growth to keep
up with the future requirements. Although unavailability of exact technical
information on the engine such as its weight, pressure ratio, TIT, cruise thrust,
s.f.c, etc. render the data in this report tentative, its comparison with other
engines clearly shows that it is a class apart from them in terms of thrust and
fuel efficiency.

17
REFERENCES
1. “The Leading Edge”, General Electric Aircraft Engines (GEAE), Spring 1993.
2. World Wide Web (WWW) Site - http://www.ge.com/geae/ge90.
3. H.Cohen, G.F.C. Rogers & H.I.H Saravanamuttoo, “Gas Turbine Theory”,
Longman, USA, Chap. 3., 3 ed., 1993.
4. J.D.Mattingly, W.H.Heiser & D.H.Daley, “Aircraft Engine Design”, AIAA
Education Series, USA, Chap. 4-5, 1987.
5. “Energy Efficient Engine”, NASA-CR-159859, June 1980.
6. D.Eckardt, “Future Engine Design Trade Offs”, X ISOABE, Sept. 1991.
7. “Jane’s All the World’s Aircraft”, UK, 1991-92.

18