133R0262 HLP-SP110 Series Operating Manual V2016-01 20160328

Download as pdf or txt
Download as pdf or txt
You are on page 1of 196

HLP-SP110 Series Operating

Manual
HLP-SP110 Series

Introduction
Thank you for purchasing and using the general-purpose vectordrive of
HLP-SP110 series.
Please read caref ully the operation manual before putting the drive
to use so as to correctly install and operate the drive, give f ull play to its
f unctions and ensure the safety. Please keep the operation manual handy for
f uture reference, maintenance, inspection and repair.
Due to the driveof a kind of powerelectronics product it must be
installed, tested and adjusted with specialized electrical engineering workers.
The marks of (Danger) , (Caution) and other symbols in
the manual remind you of the saf ety and prevention cautions during
the handling, installation, r unning and inspection. Please f ollow these
instructions to make sure the safe use of the drive. In case of any doubt
please contact our local agent for consultation. Our professional persons are
willing and ready to serve you.
The manual is subject to change without notice.

HLP-SP110 Series Operating Manual


HLP-SP110 Series

Index
Introduction I
Chapter 1 Safety Precautions 1
1.1 Before Power-up 1
1.2 During the Power-up 3
1.3 During the Operation 3
1.4 After the Power-off 4
Chapter 2 Standards and Specifications 5
2.1 Label Description 5
2.2 Particular Specifications 6
2.3 Technical Specifications 7
2.4 Derating Specifications 9
2.5 Accessories 10
Chapter 3 Mechanical and Electrical Installation 11
3.1 Mechanical Installation 11
3.1.1 Installation Environment Requirements 11
3.1.2 External and Installation Dimensions 11
3.1.3 Installation and Direction 15
3.1.4 Accessories Installation 16
3.1.5 Removal of the Front Cover 21
3.1.6 Slide Insulating Cover Operation 23
3.2 Peripheral Electrical Devices 25
3.2.1 Selection of MCCB/Fuse/Contactor 27
3.2.2 Selection of Braking Unit and Braking Resistor 28
3.2.3 Selection of EMC Filter 30
3.3 Description of Main Circuit 31
3.3.1 Schematic of Main Circuit Terminals 31
3.3.2 Main Circuit Terminal Screws and Wiring Recommended
Specifications 33
3.4 Description of Control Circuit 34
3.4.1 Schematic of Control Circuit Terminals 34
3.4.2 Control Terminals’ Screws and Wiring Recommended
Specifications 36
3.4.3 Control Curcuit Wiring 36

HLP-SP110 Series Operating Manual


HLP-SP110 Series

3.4.4 Digital Input Terminals Usage Specification 38


3.5 EMC instructions 38
3.5.1 Introduction to EMC Standard 38
3.5.2 Noise Abatement 38
3.5.3 Grounding 39
3.5.4 Leakage Current Suppression 40
3.5.5 Induction Voltage Suppression 41
Chapter 4 Operation and Display Interface 42
4.1 Local Control Panel 42
4.2 Parameter Setting 43
4.3 FWD/REV Status 44
4.4 Data Read-outs 45
4.5 View Alarm Record 47
4.6 View State Parameter 48
4.7 LED Display 49
Chapter 5 Parameter Overview 50
Chapter 6 Parameter Description 73
6.1 Group 00: Operation/Display 73
6.2 Group 01: Load and Motor 78
6.3 Group 02: Brakes 90
6.4 Group 03: Reference/Ramps 94
6.5 Group 04: Limits/Warnings 99
6.6 Group 05: Digital In/Out 104
6.7 Group 06: Analog In/Out 109
6.8 Group 07: Controllers 117
6.9 Group 08: Communication 121
6.10 Group 13: Simple PLC 125
6.11 Group 14: Special Functions 133
6.12 Group 15: Drive Information 139
6.13 Group 16: Data Readouts 141
Chapter 7 Quick Application Guide 158
7.1 Using LCP to Start/Stop the Drive 158
7.2 Using Digital Input Terminals to Start/Stop the Drive 158
7.2.1 Two-line Mode 1 158
7.2.2 Two-line Mode 2 158
7.2.3 Three-line Mode 1 159

HLP-SP110 Series Operating Manual


HLP-SP110 Series

7.2.4 Three-line Mode 2 159


7.3Multi-speed 160
7.4Analog Input as the Frequency Source 160
7.5Pulse Input as the Frequency Source 161
7.6Speed up/down 161
7.7Parameter Initialization 162
7.8Automatic Motor Adaption (AMA) 162
7.9Simple PLC 162
7.9.1 Order Execution 162
Chapter 8 Faults and Solutions 165
8.1 Fault List 165
Chapter 9 Maintenance 171
9.1 Note 171
9.2 Storage and Transport 171
Appendix A Modbus Communication Specification 172
Appendix B Copy Card Specification 189

HLP-SP110 Series Operating Manual


HLP-SP110 Series

Chapter 1 Safety Precautions


Caution Indicates misuse may damage the drive or
mechanical system .

Danger Indicates misuse may result in casualty.

1.1 Before power-up

Caution
● Check to be sure that the voltage of the main circuit AC power
supply matches the input voltage of the drive.
● Install the drive in a safe location, avoiding high temperature,
direct sunlight, humid air or water.
● The d rive can only be used at the places accredited by our
company. Any unauthorized working environment may have the
risks of fire, gas explosion, electric shock and other incidents.
● If more than one drive installed on the same control cabinet, make
additional cooling fan, so that the inside temperature is lower than
40℃,in order to prevent overheating or fire occurs.
● It will affect the service life of the drive if a contactor is installed
on the input side to control the start and stop. Generally it is
required to cont rol it th rough ter minal com mands. Special
attention should be paid to its use in the case of the start and stop
more frequently places.
● Do not install any switch component like circuit breaker or
contactor at the output of the drive. If any of such components
must be installed due process and other needs, it must be ensured
that the drive has no output when the switch acts. In addition, it
is forbidden to install any capacitor for improvement of power
factor or any varistor against thunder at the output. Otherwise
it will cause malfunctions, tripping protection and damages of
components of the drive.
● Please use an independent power supply for the drive. Do avoid
using the common power supply with an electrical welder and
other equipment with strong disturbance. Otherwise it will cause
the drive to protect or even damage the drive.
● Motor overload protection is not included in the default settings. If
this function is desired, set C01.09 (motor thermal protection) to

HLP-SP110 Series Operating Manual -1-


HLP-SP110 Series

date value ETR trip or date value ETR warning.


● Do not make any high voltage test with any component inside the
drive. These semi-conductor parts are subject to the damage of
high voltage.
● The IC board of the drive are susceptible to the effect and damage
of static electricity. Don’t touch the main circuit board.
● Installation, commissioning and maintenance must be performed
by qualified professional personnel.
● Don’t carry the front cover of the drive directly when handling.
It should be handled with the base to prevent the front cover off
and avoid the dropping of the drive, which may possibly cause the
injuries to people and the damages to the drive.

Danger
● Be sure to turn off the power supply before wiring.
● Mount the drive in the metal and other non-combustible materials
to avoid the risk of fire.
● Don’t install the drive in a space with explosive gas, otherwise,
they lead to explosion.
● R, S, T terminals are power input terminals, never mixed with
U.V.W terminals. Be sure that the wiring of the main circuit is
correct. Otherwise it will cause damages of the drive when the
power is applied to it.
● The ter minal of must be grounded separately and never
connected to N-line. Otherwise it will easily cause the protection
or errors of the drive.
● Do not dissemble or modify any internal connecting cord, wiring
or component of the drive by yourself.
● Never remodel it or exchange control boards and components by
yourself. It may expose you to an electrical shock or explosion,
etc.
● Kee p t he d r ive f rom t he rea ch of ch ild ren or pe r son s not
concerned.

-2- HLP-SP110 Series Operating Manual


HLP-SP110 Series

1.2 During the power-up

Danger
● Do not plug the connectors of the drive during the power up to
avoid any surge into the main control board due to plugging,
which might cause the damage of the drive.
● Always have the protective cover in place before the power up to
avoid electrical shock injury.

1.3 During the operation

Caution
● Do not measure the signals on circuit boards while the drive is
running to avoid danger.
● The drive has been optimized before sold. Please make proper
adjustments according to the desired functions.
● Do consider the vibration, noise and the speed limit of the motor
bearings and the mechanical devices.

Danger
● Never connect or disconnect the motor set while the drive is in
running. Otherwise it will cause over-current trip and even burn
up the main circuit of the drive.
● Never remove the front cover of the drive while the drive is
powered up to avoid any injury of electric shock.
● Do not come close to the machine when the Reset Function is
used to avoid anything unexpected. The motor may automatically
recover from fault.

HLP-SP110 Series Operating Manual -3-


HLP-SP110 Series

1.4 After the power-off

Caution
● Even in the case of the main power, the other voltage inputs and
the share load (linkage of DC intermediate circuit) all have been
disconnected from the mains, the internal of the drive still have
residual energy. Before touching any potentially live parts of the
drive, please wait at least 4 minutes for the drives of less than
22KW (including 22KW), and wait at least 15 minutes for the
drives of more than 30kW (including 30kW). Otherwise, it will
expose you to a risk of electrical shock.

-4- HLP-SP110 Series Operating Manual


HLP-SP110 Series

Chapter 2 Standards and Specifications


2.1 Label Description
SP110
SP110

Significance of the type code:


T/C: HLP-SP110 07D5 43 P20 X B X 1 C X 0 AXXVXXX
1-9 10-13 14-15 16-18 19 20 21 22 23 24 25 26 27-28 29-32

1-8 HLP-SP110Indicate Product Series


9-12 07D5 Indicate 7.5KW
13-14 43 Indicate 3-Phase AC 380V
15-17 P20 IP rating is 20
18 X Without AC choke
A With AC choke
19 X Without Brake unit
B With Brake unit
20 X Without DC choke
B With DC choke
21 1 Control panel with LED display and potentiometer
22 C With coating on PCB
23 X Reserved
24 0 Domestic sale
1 Overseas sale
25 A Basic IO board
B Advanced IO board
26-27 XX Reserved
28-31 VXXX Indicate software version number,
such as V235 means the version number is 2.35.

Note: For SP110 power less than 7.5kW (including) model, advanced IO
board is standard conf iguration, basic IO board is optional, please specif y
when ordering if need basic IO board; For 11kW and above power model, only
advanced IO board is supported.

HLP-SP110 Series Operating Manual -5-


HLP-SP110 Series

2.2 Particular Specifications


Input Output Rated Suit-
Net
cur- cur- pow- able
Model Input voltage weight
rent rent er motor
/KG
/A /A /KW /kW
3×380-440V50/60Hz 3.7 2.3
HLP-SP1100D7543 0.75 0.75 1.3
3×440-480V50/60Hz 3.2 2.1
3×380-440V50/60Hz 6.4 4
HLP-SP11001D543 1.5 1.5 1.3
3×440-480V50/60Hz 5.5 3.6
3×380-440V50/60Hz 8.9 5.6
HLP-SP11002D243 2.2 2.2 1.3
3×440-480V50/60Hz 7.7 5.1
3×380-440V50/60Hz 15.8 9.9
HLP-SP11004D043 4.0 4.0 2
3×440-480V50/60Hz 13.6 9
3×380-440V50/60Hz 21.3 13.3
HLP-SP11005D543 5.5 5.5 2
3×440-480V50/60Hz 18.4 12.1
3×380-440V50/60Hz 28.3 17.7
HLP-SP11007D543 7.5 7.5 2.5
3×440-480V50/60Hz 24.4 16.1
3×380-440V50/60Hz 35.9 25
HLP-SP110001143 11 11 5.8
3×440-480V50/60Hz 31.4 22.7
3×380-440V50/60Hz 43.4 32
HLP-SP110001543 15 15 5.8
3×440-480V50/60Hz 38.8 29.1
3×380-440V50/60Hz 51.5 38
HLP-SP11018D543 18.5 18.5 8
3×440-480V50/60Hz 46.1 34.5
3×380-440V50/60Hz 61.0 45
HLP-SP110002243 22 22 8
3×440-480V50/60Hz 54.5 40.9
3×380-440V50/60Hz 73 61
HLP-SP110003043 30 30 19
3×440-480V50/60Hz 64 52
3×380-440V50/60Hz 72 75
HLP-SP110003743 37 37 22
3×440-480V50/60Hz 65 68
3×380-440V50/60Hz 86 91
HLP-SP110004543 45 45 26
3×440-480V50/60Hz 80 82
3×380-440V50/60Hz 110 112
HLP-SP110005543 55 55 26
3×440-480V50/60Hz 108 110
3×380-440V50/60Hz 148 150
HLP-SP110007543 75 75 37
3×440-480V50/60Hz 135 140
3×380-440V50/60Hz 175 180
HLP-SP110009043 90 90 60
3×440-480V50/60Hz 154 160
3×380-440V50/60Hz 206 215
HLP-SP110011043 110 110 60
3×440-480V50/60Hz 183 190
3×380-440V50/60Hz 251 260
HLP-SP110013243 132 132 60
3×440-480V50/60Hz 231 240
3×380-440V50/60Hz 304 315
HLP-SP110016043 160 160 99
3×440-480V50/60Hz 291 302

-6- HLP-SP110 Series Operating Manual


HLP-SP110 Series

3×380-440V50/60Hz 350 365


HLP-SP110018543 185 185 99
3×440-480V50/60Hz 320 335
3×380-440V50/60Hz 381 395
HLP-SP110020043 200 200 99
3×440-480V50/60Hz 348 361
3×380-440V50/60Hz 420 435
HLP-SP110022043 220 220 99
3×440-480V50/60Hz 383 398
3×380-440V50/60Hz 472 480
HLP-SP110025043 250 250 250
3×440-480V50/60Hz 436 443
3×380-440V50/60Hz 525 540
HLP-SP110028043 280 280 250
3×440-480V50/60Hz 475 490
3×380-440V50/60Hz 590 605
HLP-SP110031543 315 315 250
3×440-480V50/60Hz 531 540
3×380-440V50/60Hz 647 660
HLP-SP110035543 355 355 250
3×440-480V50/60Hz 580 590
3×380-440V50/60Hz 718 745
HLP-SP110041543 415 415 250
3×440-480V50/60Hz 653 678
3×380-440V50/60Hz 771 800
HLP-SP110045043 450 450 250
3×440-480V50/60Hz 704 730

2.3 Technical Specifications

Item Specification
Supply voltage three phase 380~480V -20%~+10%;
Power
Frequency 48~62Hz;
supply
Max. imbalance 3%;
three phase 0-100% of supply volt-
Motor Output voltage
age;
output
Output frequency V/F : 0-400Hz , VVC+: 0-200Hz;
Control mode V/F, VVC+;
Start torque 0.5Hz 150%;
Overload capacity 110% 60s, 150% 1s;
PWM switch frequen-
2~16kHz;
cy
Main
control Digital: 0.001Hz;
Speed setting resolu-
functions Analogy: 0.5‰ of the max. operating
tion
frequency ;
Speedopen-loop
30~4000 rpm: tolerance±8 rpm;
control accuracy
Control command
LCP, digital terminal, local bus;
source

HLP-SP110 Series Operating Manual -7-


HLP-SP110 Series

Frequency setting
LCP, analog, pulse, local bus;
source
Selectable 4-speed steps ramp up and
Ramp control
down times 0.05-3600.00s;
Speed Open-loop Control; Process Closed-loop Control;
Torque Open-loop Control; AMA Function;Motor Magnetisa-
Basic tion; Slip Compensation;Torque compensation;Automatic
Functions Voltage Regulation; V/F Control, DC Brake; AC brake; Speed
Limit; Current Limit; FlyingStart; Reset Function; Counter;
Timer;
Wobble Function; Jogging; Multi-speed Control via Digital
Applica-
input; SLC(including Order Control and Parallel Control);
tion Func-
Mechanical Braking; UP/DOWN ; Catch up /Slow down;
tions
Relative Scaling Reference etc.
Missing Motor Phase Protection; Low-voltage Protection;
Over-voltage Protection; Over-current Protection; Output
Phase Loss Protection; Output Short Circuit Protection;
Protection Output Grounding Fault Protection;Motor Thermal Protec-
Functions tion; Live Zero Timeout Function;AMA Fails; CPU Fault;
EEPROM Faults; Buttonfreeze; Duplicate Fails; LCP Invalid;
LCP Incompatible; Parameter Read-only; Reference Out of
Range; Invalid While Running etc.
5 digital inputs
2 analoginput, both can receive voltage or
Input current signals.
Advanced In the AI terminal can choose the current or
IO resistance signal by jumper.
board 6relay output;
control Output 2 analogoutput (1 can be selected as current
terminals output or voltage output via jumper switch).
1 +10V, max current output 10mA;
Power supply
1 24V, max current output 200mA;
Communication RS+, RS-, max baud rate 115200bit/s;
5 digital inputs;
Input 2analog input, it can receive voltage or cur-
Basic rent signals.
IO 2relay output;
board Output 2analog input; it can be selected as current
control output or voltage output via jumper switch.
terminals
Power supply 1 +10V, max current output 10mA;
Communication RS+, RS-, max baud rate 115200bit/s;

-8- HLP-SP110 Series Operating Manual


HLP-SP110 Series

8 segments, 5 numeric Display frequency, warnings, status


displays and so on;
Light FWD, REV, HZ, A, RPM
Indicator
display various status of the drive;
Frequency setting, output frequen-
cy, feedback value, output current,
Display DC link voltage, output voltage,
output power, input terminals state,
Data read-outs output terminals state, analogue
input , analogue output, 1-10 fault
records and accumulated working
time etc.;

Enclosure IP20;
-10℃~50℃, derating use when over
Ambient temperature
40℃;
5%-85% (95% without conden-
Humidity
sation);
Environ-
ment ≤75kW: 1.14g;
Vibration test
≥90kW: 0.7g;
Max. altitude above 1000m, derating use when more
sea level than 1000 meters;
Shield cable: 50 meters, unshield
Motor cable length
cable: 100 meters;
DC choke ≥37kW Built-in
others
Braking unit ≤22kW Built-in

2.4 Derating Specifications


Derating for ambient temperature: If the drive is operated over
40℃ ambient temperature, the continuous output cur rent should
be decreased.The d r ive has been desig ned for operation at max
50℃ ambient temperationwith one motor size smaller than normal.
Continuous operation at full load at 50℃ ambient temperation will
reduce the lifetime of the drive.
Deratingfor low air pressure: The cooling capability of air is
decreased at low air pressure. Below 1000m altitude no de-rating is
necessary but above 1000m the ambient temperature or the maximum
output current should be decreased.Dcrease the output by 1% per 100m
altitude above 1000m or reduce the max.ambient temperature by 1
degree per 200m.

HLP-SP110 Series Operating Manual -9-


HLP-SP110 Series

2.5 Accessories
LCP-02

Network
Cable Cradle-01
HLP-SP110

LCP-03

CopyCard-01

Base-01 Base-02 Base-03

Model Specif ication Remark


LCP-02 has the same external
and installation dimensions and
installation method with LCP-01.
LCP-02 Random standard
The standard length of extension
cable is 15 meters when mounting
LCP on control cabinet.
LCP-03 has the same installation Optional, please
LCP-03 dimensions with HLP-A control specify when
panel (OP-AB01). ordering
Optional, please specify
Cradle-01 LCP-02 installation.
when ordering
Copy Card can copy parameters Optional, please specify
CopyCard-01
from one drive to another when ordering
Network Connect LCP to the drive when Do not offer, self
Cable mounting LCP on control cabinet. procurement
Optional, please
Base-01 For 110~160kW
specify when ordering
Optional, please
Base-02 For 185~250kW
specify when ordering
Optional, please
Base-03 For 280~450kW
specify when ordering

- 10 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Chapter 3 Mechanical and Electrical Installation


3.1 Mechanical Installation
3.1.1 Installation Environment Requirements
1. Ambient temperature in the range of -10℃~ 50℃;
2. Drive should be installed on surface of flame retardant object,
with adequate surrounding space for heat dissipation;
3. Installation should be performed where vibration is less than 1.14g
(<= 75kW) or 0.7g (>= 90kW);
4. Avoid from moisture and direct sunlight;
5. Do not expose to an atmosphere with flammable gases, corrosive
gases, explosive gases or other harmful gases;
6. Protect the cooling fan by avoiding oil, dust and metal particles;
7. Prevent drilling residues, wire ends and screws falling into drive;

3.1.2 External and Installation Dimensions

three phase 380V0.75~7.5kW

HLP-SP110 Series Operating Manual - 11 -


HLP-SP110 Series

three phase 380V 11~22kW

three phase 380V 30~90kW

- 12 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

three phase 380V 110~250kW

HLP-SP110

Base Profile

three phase 380V 280~450kW

HLP-SP110 Series Operating Manual - 13 -


HLP-SP110 Series

External and installation dimensions(unit: mm)


Model A B C D E F G
HLP-SP1100D7543
HLP-SP11001D543 104 125 194 210 150 4.5 -
HLP-SP11002D243
HLP-SP11004D043
124 145 230 250 165 4.5 -
HLP-SP11005D543
HLP-SP11007D543 133 155 243 263 175 4.5 -
HLP-SP110001143
148 192 340 365 189 6.5 -
HLP-SP110001543
HLP-SP11018D543
150 214 395 420 194 6.5 -
HLP-SP110002243
HLP-SP110003043
HLP-SP110003743 240 292 492 517 229 9 -
HLP-SP110004543
HLP-SP110005543
240 292 537 562 249 9 -
HLP-SP110007543
HLP-SP110009043 240 292 640 655 277 9
HLP-SP110011043
HLP-SP110013243 220 350 765 799 375 10.5 280
HLP-SP110016043
HLP-SP110018543
HLP-SP110020043
345 486 863 900 390 10.5 410
HLP-SP110022043
HLP-SP110025043
HLP-SP110028043
HLP-SP110031543
HLP-SP110035543 424 600 304 1560 500 15 -
HLP-SP110041543
HLP-SP110045043

- 14 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

3.1.3 Installation and Direction


1.Single Installation
The drive must be installed vertically with smooth ventilation.
Enough space must be left around the drive to ensure good
cooling, as shown below:

Min:100mm

Min:100mm

2.Side by Side Installation


The drive can be mounted side by side, a minimum space must be
reserved above and below the enclosure, as shown below:

Min:100mm

Min:100mm

HLP-SP110 Series Operating Manual - 15 -


HLP-SP110 Series

3.Upper and Lower Installation


If several drives need to be installed together in one cabinet, upper
and lower installation can be adopted. Enough space must be
reserved to ensure effective cooling, as shown below:

Min:100mm

Min:100mm

Min:100mm

3.1.4 Accessories Installation


1. LCP-02 Installation
LCP-02 is the length of extension cable (network cable) when
mounting LCP on control cabinet.
LCP-02 are shown below (unit: mm):

- 16 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

LCP-02 outside, a cradle is needed. The external dimensions of the


cradle are shown below (unit: mm):

LCP-02 are shown below:

This cradle
is suitable
for 1.0-
2.0mm
thickness
sheet metal
parts.
Press and hold
the snap roots
when install-
ation,using
buckle defor-
mation install
Stepl:Open a hole in line with the size sheet metal.
of the control panel in the position need Step2:Install the LCP according to the
to instal the LCP,hole size,as shown: direction of the arrow.

Recommended
to install
vertical
mounting
position
arrow,press
with uniform
force.
Step 4: Install the external LCP
Step 3:The LCP is installed in the cradle, communication cable, insert into RJ45
according to the direction of the arrow. terminal from the bottom of hole.

HLP-SP110 Series Operating Manual - 17 -


HLP-SP110 Series

2. LCP-03 Installation
The external dimensions of LCP-03 are shown below (unit: mm):

The installation steps of LCP-03 are shown below:

Step1:该小面板适用于厚度
步骤 1:Open a hole in the control panel where
1.0mm~2.0mm 钣 Step 2: Install the LCP according to the
步骤 2:按照箭头方向,将小面板固定在
it is needed to install LCP-01 or LCP-02, the
金件,在需要安装小面板的位置开一个孔,开 direction of the arrow.
钣金上面。
hole size is as shown.
孔尺寸如图所示:
Projection Scale / Paper size Matr.

1:1 / A3 Danf

Last revised by Date Desig

DANFOSS DRIVES A/S


Confidential: Property of Danfoss Drives A/S. Not to be handed over to,
copied or used by third party. Two- or three dimensional reproduction Part
of contents to be authorized by Danfoss Drives A/S.
PDM controlled drawing. - Hard copy not valid without frozen date in ID stamp. Rev.

Step 3: Install the LCP communication cable,


步骤 3:安装外引键盘
insert RJ45from
into RJ45 terminal 通讯电缆,从底部
the bottom
hole.孔插入。
RJ45

Projection Scale / Paper size


- 18 - HLP-SP110 Series Operating Manual
Matr./Spec.

1:1 / A3 Danfoss standard

revised by Date Designation


odel: LCP.ASSEM

DANFOSS DRIVES A/S


nfidential: Property of Danfoss Drives A/S. Not to be handed over to,
ied or used by third party. Two- or three dimensional reproduction Part no. Sh.
ontents to be authorized by Danfoss Drives A/S. LCP 2 of 2
M controlled drawing. - Hard copy not valid without frozen date in ID stamp. Rev.
HLP-SP110 Series

3. Base Installation
Base-01 is for 90~132kW, its external dimensions are shown below
(unit: mm):
251.5

251.5

370 370 349 349

Base-02 is for 160~220kW, its external dimensions are shown


below (unit: mm):
251.5
251.5

4 The parts must be installed


4 The parts
to the
must
position,
be installed to the position,
according to the requirements
accordingoftothe
thedrawings.
requirements of the drawings.
5 133B4391 5 133B4391
screw flat M5x12 screw flat M5x12
16
4 358
506 133B5810-4-1 4 133B5810-4-1
ka kou ka kou 2
3 358
506 133B5809-14 3 133B5809-14
front plate,a7 front plate,a7 1 ST
2 133B5810-3 2 133B5810-3
right plate,a7 right plate,a72 ST
Base-03 is for 250~450kW,
1 its external dimensions are shown
133B5809-1 1 133B5809-1
bottom frame,a7 bottom frame,a7
1 ST
NO Part number
NO Part number
Designation Designation
quantity Ma
below (unit: mm): Projection Scale / Paper size Projection Scale / Paper size Matr./Spec.

see
1:5 / A3 1:5 / A3 Danfoss standard

Last revised by Date Last revised by Date Designation

jinping jinping DANFOSS


2013.1.10 DRIVES A/S
2013.1.10 botto
DANFOSS DRIVES
The
Confidential: Property of Danfoss Drives4Confidential:
A/S. Not parts
to be handedmust
Property ofover to,beDrives
Danfoss installed
A/S. Not to the
to be position
handed over to,
Part no.
copied or used by third party. Two- or three according
copied
dimensional
or used by thirdto theTwo-
reproduction
party. requirements ofreproduction
or three dimensional the drawings
of contents to be authorized by Danfoss ofDrives
contents
A/S. to be authorized by Danfoss Drives A/S. 133B580
The parts must be installed to the position
valid5
4 controlled drawing. - Hard copy notPDM
PDM
133B4391controlled
without frozen
drawing.
date-inHard
ID stamp. Rev.
copy not valid without frozen date in ID stamp.
screws flat M5x12 001
according to the requirements
4 of the drawings ka kou
133B5810-4-1
3 133B5810-4 front plate,a8
5 133B4391 screws flat M5x12 16
2 133B5810-3 right plate,a8
4 133B5810-4-1 1 ka kou
133B5810-1 bottom frame,a82
3 133B5810-4 NO front
Partplate,a8
number 1
Designation ST12
2 133B5810-3 right plate,a8 Projection 2 Scale / Paper size ST12
1 133B5810-1 bottom 1:5
frame,a8
/ A3 1 ST12
NO Part number Designation quantity Matria
Last revised by Date
Projection Scale / Paper size Matr./Spec.

jinping 2013.1.8 DANFOSS DRIVESsee


A/S no
1:5Confidential:
/ A3 Property of Danfoss Drives A/S. Not to be handed over to, Danfoss standard

copied or used by third party. Two- or three dimensional reproduction


of contents to be authorized by Danfoss Drives A/S.
Last revised by Date Designation
PDM controlled drawing. - Hard copy not valid without frozen date in ID stamp.
jinping 2013.1.8 DANFOSS DRIVES A/S
Confidential: Property of Danfoss Drives A/S. Not to be handed over to,
bottom,
copied or used by third party. Two- or three dimensional reproduction Part no.
of contents to be authorized by Danfoss Drives A/S. 133B5810
PDM controlled drawing. - Hard copy not valid without frozen date in ID stamp. Rev.
001

HLP-SP110 Series Operating Manual - 19 -


HLP-SP110 Series

The installation steps of Base-01 and Base-02 are the same, shown
below:

Step1: Original state.

Step2: Remove the bottom cable entry sheet metal and fixing screws.

Step3: Move the rubber pieces from the bottom of the sheet metal to the
Base.

Step4: Use M5 * 12 screws to fix the Base and drive.


HL
P-S
K1
90

Projection Scale / Paper size Matr./Spec.

1:5 / A1 Danfoss standard

Last revised by Date Designation

DANFOSS DRIVES A/S


Confidential: Property of Danfoss Drives A/S. Not to be handed over to,
copied or used by third party. Two- or three dimensional reproduction Part no. S
of contents to be authorized by Danfoss Drives A/S. HP103_110KW 2
PDM controlled drawing. - Hard copy not valid without frozen date in ID stamp. Rev.
001

- 20 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

The installation steps of Base-03 are shown below:

Step1: Original state

HLP
-SK1
90

Step2: Use 12 M8 * 20 screws to fix the Base and drive. HLP-S


K190

3.1.5 Removal of the Front Cover


It is needed to remove the front cover before wiring the main
circuit and control circuit.

≤7.5kW
Use a screwdriver to push out the hook of the front cover inward.

HLP-SP110 HLP-SP110

HLP-SP110 Series Operating Manual - 21 -


HLP-SP110 Series

11~22kW
Use a screwdriver to push out the hook of the front cover inward.

HLP-SP11
HLP-SP11 0
0

30~250kW
Use a screwdriver to loosen the screws on the front cover.

HLP-S
P110
HLP-S
HLP-S P110
P110

- 22 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

280~450kW
Screw the lock on the door.

HLP-SP110

Lock

3.1.6 Slide Insulating Cover Operation


The drive which power is ≤ 7.5kW has built-in slide insulating
cover between main circuit and control circuit. Its operation is
shown below:
Step 1: Open the front cover, push the slide insulating cover handles
inwards and pull them to the top.

Push the slide insulating cover handles


Front Cover inwards and pull them to the top.

HLP-SP110 Series Operating Manual - 23 -


HLP-SP110 Series

Step 2: Wiring IO and main circuit, push the slide insulating cover
handles inwards and pull them to the bottom, cover the front cover.

Front Cover Push the slide insulating cover handles


inwards and pull them to the bottom.
Note: If the slide insulating cover is not be pulled down, the front cover will
be not assembled in place.

The slide insulating


Front Cover Error
cover is on top

- 24 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

3.2 Peripheral Electrical Devices


The peripheral electrical devices of the drive are shown below:

Power supply

MCCB

Electromagnetic
contactor

AC input
reactor

Noise filter on
input side HLP-SP110

Noise filter on
output side

Braking unit
AC output
reator
Braking resistor

Motor

HLP-SP110 Series Operating Manual - 25 -


HLP-SP110 Series

Part Mounting Location Function Description


Interrupt the power supply
Power receiving
MCCB when overcurrent occurs
side
ondownstream devices.
Do not start and stop the drive
Between MCCB frequently by switchingthe
Contactor and drive input contactor on and off (less than
side twice per minute) noruse it to
directly start the drive.
Improve the power factor of the
input side;
Eliminate the input
current unbalance due to
unbalancebetween the power
AC input reactor Drive input side phases;
Eliminate the higher harmonics
of the input sideeffectively;
prevent other devices from
beingdamaged due to distortion
of the voltage waveform;
Decrease the conduction
interference flowing from the
power end to the drive and
improve the antiinterference
EMC Input filter Drive input side
capacity of the drive;
Reduce the external conduction
and radiation
interference of the drive;
≤22kW Braking
Braking unit Consume the motor feedback
unit is standard
Braking resistor energy to achieve rapid braking.
configuration
Reduce the external conduction
EMC Output filter Drive output side and radiation
interference of the drive.
Degrade the motor insulation
performance and damage the
Between the drive motor in the long run;
output side and Generate large leakage current
AC output reactor and cause frequent ACdrive
themotor, close to
protection trips;
the drive If the distance between the drive
and the motor isgreater than 100
m, install an AC output reactor;

- 26 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

3.2.1 Selection of MCCB/Fuse/Contactor

Model MCCB (A) Fuse (A) Contactor (A)


HLP-SP1100D7543 10 10 10
HLP-SP11001D543 10 10 10
HLP-SP11002D243 16 16 10
HLP-SP11004D043 25 25 25
HLP-SP11005D543 32 32 25
HLP-SP11007D543 40 40 32
HLP-SP110001143 63 63 40
HLP-SP110001543 63 63 63
HLP-SP11018D543 100 100 63
HLP-SP110002243 100 100 100
HLP-SP110003043 150 150 100
HLP-SP110003743 150 150 100
HLP-SP110004543 175 175 135
HLP-SP110005543 200 200 150
HLP-SP110007543 250 250 200
HLP-SP110009043 300 300 240
HLP-SP110011043 350 350 260
HLP-SP110013243 400 400 350
HLP-SP110016043 500 500 450
HLP-SP110018543 630 630 450
HLP-SP110020043 630 630 550
HLP-SP110022043 800 800 550
HLP-SP110025043 800 800 630
HLP-SP110028043 800 800 630
HLP-SP110031543 1000 1000 630
HLP-SP110035543 1000 1000 800
HLP-SP110041543 1200 1200 800
HLP-SP110045043 1200 1200 1000

HLP-SP110 Series Operating Manual - 27 -


HLP-SP110 Series

3.2.2 Selection of Braking Unit and Braking Resistor


1. The guide of AC input reactor selection

Inductance
Maximum
Ratedcurrent (mH)
Model continuous
(A) & 3% Impedance
current(A)

HLP-SP1100D7543 3.5 5.2 16


HLP-SP11001D543 6 9 8
HLP-SP11002D243 8.5 13 5.5
HLP-SP11004D043 14.5 22 2.99
HLP-SP11005D543 20 30 2.2
HLP-SP11007D543 25 37.5 1.6
HLP-SP110001143 33 49.5 1.08
HLP-SP110001543 42 63 0.8
HLP-SP11018D543 50 75 0.65
HLP-SP110002243 60 90 0.54
HLP-SP110003043 80 120 0.45
HLP-SP110003743 80 120 0.36
HLP-SP110004543 100 150 0.3
HLP-SP110005543 120 180 0.25
HLP-SP110007543 160 240 0.18
HLP-SP110009043 200 300 0.15
HLP-SP110011043 250 375 0.12
HLP-SP110013243 300 450 0.1
HLP-SP110016043 350 525 0.085
HLP-SP110018543 400 600 0.07
HLP-SP110020043 450 675 0.065
HLP-SP110022043 500 750 0.06
HLP-SP110025043 560 710 0.05
HLP-SP110028043 630 780 0.03
HLP-SP110031543 700 880 0.0215
HLP-SP110035543 770 970 0.017
HLP-SP110041543 860 1070 0.012
HLP-SP110045043 860 1070 0.012

- 28 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

2. the guide of AC output reactor selection

Rated Saturation
Inductance
Model current current (A)
(mH)
(A) & 3% Impedance
HLP-SP1100D7543 2.3 4.8 14.39
HLP-SP11001D543 4 8.5 7.19
HLP-SP11002D243 5.6 11.9 4.9
HLP-SP11004D043 9.9 21 2.69
HLP-SP11005D543 13.3 28.2 1.96
HLP-SP11007D543 17.7 37.5 1.43
HLP-SP110001143 25 53 0.98
HLP-SP110001543 32 67.8 0.72
HLP-SP11018D543 38 80.6 0.58
HLP-SP110002243 45 95.4 0.49
HLP-SP110003043 61 129 0.362
HLP-SP110003743 75 159 0.294
HLP-SP110004543 91 193 0.242
HLP-SP110005543 112 238 0.197
HLP-SP110007543 150 318 0.147
HLP-SP110009043 180 382 0.123
HLP-SP110011043 215 456 0.103
HLP-SP110013243 260 551 0.085
HLP-SP110016043 315 668 0.070
HLP-SP110018543 365 774 0.060
HLP-SP110020043 395 838 0.056
HLP-SP110022043 435 923 0.051
HLP-SP110025043 480 1020 0.009
HLP-SP110028043 540 1145 0.008
HLP-SP110031543 605 1280 0.0055
HLP-SP110035543 660 1400 0.004
HLP-SP110041543 745 1580 0.0035
HLP-SP110045043 745 1580 0.003

HLP-SP110 Series Operating Manual - 29 -


HLP-SP110 Series

3.2.3 Selection of EMC Filter

EMC Input Filter EMC Output Filter


Model Rated Rated
Recommend- Recommend-
Current Current
ed Model* ed Model*
(A) (A)
HLP-SP1100D7543 5 NFI-005 5 NFO-005
HLP-SP11001D543 5 NFI-005 5 NFO-005
HLP-SP11002D243 10 NFI-010 10 NFO-010
HLP-SP11004D043 10 NFI-010 10 NFO-010
HLP-SP11005D543 20 NFI-020 20 NFO-020
HLP-SP11007D543 20 NFI-020 20 NFO-020
HLP-SP110001143 36 NFI-036 36 NFO-036
HLP-SP110001543 36 NFI-036 36 NFO-036
HLP-SP11018D543 50 NFI-050 50 NFO-050
HLP-SP110002243 50 NFI-050 50 NFO-050
HLP-SP110003043 65 NFI-065 65 NFO-065
HLP-SP110003743 80 NFI-080 80 NFO-080
HLP-SP110004543 100 NFI-100 100 NFO-100
HLP-SP110005543 150 NFI-150 150 NFO-150
HLP-SP110007543 150 NFI-150 150 NFO-150
HLP-SP110009043 200 NFI-200 200 NFO-200
HLP-SP110011043 250 NFI-250 250 NFO-250
HLP-SP110013243 250 NFI-250 250 NFO-250
HLP-SP110016043 300 NFI-300 300 NFO-300
HLP-SP110018543 400 NFI-400 400 NFO-400
HLP-SP110020043 400 NFI-400 400 NFO-400
HLP-SP110022043 600 NFI-600 600 NFO-600
HLP-SP110025043 900 NFI-900 900 NFO-900
HLP-SP110028043 900 NFI-900 900 NFO-900
HLP-SP110031543 900 NFI-900 900 NFO-900
HLP-SP110035543 1200 NFI-1200 1200 NFO-1200
HLP-SP110041543 1200 NFI-1200 1200 NFO-1200
HLP-SP110045043 1200 NFI-1200 1200 NFO-1200
* Recom mended models is the Shanghai Eag top Elect ronic
Technology Co., Ltd. products, website: http://www.eagtop.com/

- 30 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

3.3 Description of Main Circuit


3.3.1 Schematic of Main Circuit Terminals

three phase380V 7.5~22kW

Three phase 380V 30~90kW

HLP-SP110 Series Operating Manual - 31 -


HLP-SP110 Series

Three phase 380V 110~250kW

Three phase 380V 289~450kW


Description of main circuit terminals:
Symbol Function
R, S, T Power input, Single phase connected to R, T
U, V, W Power output, connect to the motor
PE Ground terminal

- 32 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

3.3.2 Main Circuit Terminal Screws and Wiring


Recommended Specifications
Input Input Ground
Ground
Input Output and and
Termi- Terminal
Model Cable Cable Output Output
nal Torque
(mm2) (mm2) Terminals’ Terminals’
Screw
Screws Torque
HLP-SP1100D7543 1 1 M3.5 0.8-1.0 M4 1.0-1.2
HLP-SP11001D543 1 1 M3.5 0.8-1.0 M4 1.0-1.2
HLP-SP11002D243 1 1 M3.5 0.8-1.0 M4 1.0-1.2
HLP-SP11004D043 1.5 1.5 M4 1.0-1.2 M4 1.0-1.2
HLP-SP11005D543 1.5 1.5 M4 1.0-1.2 M4 1.0-1.2
HLP-SP11007D543 2.5 1.5 M4 1.0-1.2 M4 1.0-1.2
HLP-SP110001143 4 2.5 M4 1.0-1.2 M6 2.0-2.5
HLP-SP110001543 6 4 M4 1.0-1.2 M6 2.0-2.5
HLP-SP11018D543 10 4 M5 1.6-2.0 M6 2.0-2.5
HLP-SP110002243 10 6 M5 1.6-2.0 M6 2.0-2.5
HLP-SP110003043 10 10 M8 8-10 M6 2.0-2.5
HLP-SP110003743 16 16 M8 8-10 M6 2.0-2.5
HLP-SP110004543 16 16 M8 8-10 M6 2.0-2.5
HLP-SP110005543 25 25 M8 8-10 M6 2.0-2.5
HLP-SP110007543 35 35 M8 8-10 M6 2.0-2.5
HLP-SP110009043 70 70 M10 12-16 M10 12-16
HLP-SP110011043 70 70 M10 12-16 M10 12-16
HLP-SP110013243 95 95 M10 12-16 M10 12-16
M12*1
HLP-SP110016043 120 150 12-16 M10*2 12-16
(M10*2)
M12*1
HLP-SP110018543 150 185 12-16 M10*2 12-16
(M10*2)
M12*1
HLP-SP110020043 185 185 12-16 M10*2 12-16
(M10*2)
M12*1
HLP-SP110022043 240 240 12-16 M10*2 12-16
(M10*2)
HLP-SP110025043 70*2 70*2 M10*1 26-33 M8*1 13-16
HLP-SP110028043 95*2 95*2 M10*1 26-33 M8*1 13-16
HLP-SP110031543 95*2 95*2 M10*1 26-33 M8*1 13-16
HLP-SP110035543 120*2 120*2 M10*1 26-33 M8*1 13-16
HLP-SP110040043 120*2 120*2 M10*1 26-33 M8*1 13-16
HLP-SP110041543 120*2 120*2 M10*1 26-33 M8*1 13-16
HLP-SP110045043 120*2 120*2 M10*1 26-33 M8*1 13-16

HLP-SP110 Series Operating Manual - 33 -


HLP-SP110 Series

Note: This specification is under using single-core line VV and


25℃, if use other cables or under higher temperature environment, please
refer to electrical manual.

3.4 Description of Control Circuit


3.4.1 Schematic of Control Circuit Terminals
1. Schematic of Basic IO board

2.Schematic of Advanced IO board

- 34 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Terminals’ specification:
Symbol Description Specification
24Vpower Maxload 200mA, with over load and short
VDD
supply circuit protection functions.
Maxload 10mA, with over load and short
+10V 10Vpower supply
circuit protection functions.
1. Logic:
FOR, >DC 19V Logic: 0;
REV, DI1, <DC 14V Logic: 1;
Digital input
DI2, 2. Voltage: DC0-24v;
DI3, 3. Input resistance: 5kΩ;
4. Input voltage Rang:Max ±30v;
COM Digital ground Isolated from internal GND.
Both VI and AI can be configurated to
0-20mA or 0-10Vby paramters:
VI, AI Analog input
1. Input Impedance: about 10kΩ;
2. Input Impedence: ≤200Ω;
VO can be selected to the current output
or voltage output via J2, default is: voltage
output;
VO, AO Analog output AO only has current output mode;
1. Output Mode: 0~20mAor 0~10V;
2. Voltage Output: load larger than 500Ω;
3. Current Output: load larger than 500Ω;
Analog
GND and communica- Isolated from internal COM.
tion ground
Relay
1. Resistive Load: 250VAC 3A/30VDC 3A;
(FA-FB-
Relay output 2. Inductive Load: 250VAC 0.2A/24VDC
FC, KA-
0.1A (cosφ= 0.4);
KB)
RS485
RS+、RS- Max baud rate: 115200bit/s;
communication
(FA-FB-
FC、KA1-
1、Resistive load:250VAC 3A/30VDC
KB1、KA2-
Ready 3A;
KB2、KA3-
2、Inductive load:250VAC 0.2A/24VDC
KB3、KA4-
0.1A
KB4、KA5-
KB5)

HLP-SP110 Series Operating Manual - 35 -


HLP-SP110 Series

3.4.2 Control Terminals’ Screws and Wiring Recommended


Specifications
Cable types Cable specifications (mm 2) Torque (n∙m)
Shielded cables 0.4 0.4

3.4.3 Control Curcuit Wiring


1. Basic IO board wiring:

- 36 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

2. Advanced IO board wiring

HLP-SP110 Series Operating Manual - 37 -


HLP-SP110 Series

3.4.4 Digital Input Terminals Usage Specification


1. Open collector NPN mode wiring
External Drive
Controller

Jumper Switch J3

Opto-
Isolator
Y1

Opto-
Isolator
Yn

Shielded
Cable Near-
end Ground

While using this mode, J3 1-2 must be connected (default state:


VDD connects to OP). Basic IO board only supports this mode.

3.5 EMC instructions


3.5.1 Introduction to EMC Standard
The HLP-SP110 series satisfies the requirements of standardIEC/
EN61800-3: 2004 (Adjustable speed electricalpower drive systems part
3:EMC requirements and specific test methods).

3.5.2 Noise Abatement


1. When peripheral equipment and the drive share the power supply
of one system, noise from the drive may be transmitted to other
equipment in this system via power lines and result in misoperation
and/or faults. In such a case, the following measures could be taken:
a. Mount input noise filter at input terminal of the drive;
b. Mount power supply filter at power input terminal of affected
equipment;
c. Use isolation transformer to isolate the noise transmission path
between other equipment and the drive.
2. As the wiring of peripheral equipment and the drive constitutes a
circuit, the unavoidable earthing leakage current of drive will cause
equipment misoperation and/or faults. Disconnect the grounding

- 38 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

connection of equipment may avoid this misoperation and/or faults.


3. Sensitive equipment and signal lines shall be mounted as far away
from drive as possible.
4. Signal lines should be provided with shielded layer and reliably
grounded. Alternatively, signal cable could be put into metallic
conduits between which the distance shall be no less than 20cm,
and shall be kept as far away from drive and its peripheral devices,
cables as possible. Never make signal lines in parallel with power
lines or bundle them up.
5. Signal lines must or thogonally cross power lines if this cross
inevitable.
6. Motor cables shall be placed in thick protective screen like more
than 2mm-thick pipelines or buried cement groove, also, power lines
can be put into metallic conduit and grounded well with shielded
cables.
7. Use 4-core motor cables of which one is grounded at close side of the
drive and the other side is connected to motor enclosure.
8. Input and output terminals of drive are respectively equipped with
radio noise filter and linear noise filter. For example, ferrite common
mode choke can restrain radiation noise of power lines.

3.5.3 Grounding
Recommended ground electrode is shown in the figure below:

Drive Other
Devices

1. Use to the fullest extent the maximum standard size of grounding


cables to reduce the impedance of grounding system;
2. Grounding wires should be as short as possible;
3. Grounding point shall be as close to the drive as possible;
4. One wire of 4-core motor cables shall be grounded at the drive side
and connected to grounding terminal of motor at the other side.
Better effect will be achieved if motor and drive are provided with

HLP-SP110 Series Operating Manual - 39 -


HLP-SP110 Series

dedicated ground electrodes;


5. When grounding terminals of various parts of system are linked
together, leakage current turns into a noise source that may influence
other equipment in the system, thus, grounding terminals of the
drive and other vulnerable equipment should be separated;
6. Grounding cable shall be kept away from input& output of noise-
sensitive equipment.

3.5.4 Leakage Current Suppression


Leakage current passes through the line-to-line and ground distributed
capacitors at input & output sides of drive, and its size is associated
with the capacit ance of dist r ibuted capacitor and the car r ier
frequency. Leakage current is classified into ground leakage current
and line-to-line leakage current.
1. Ground leakage current not only circulates inside drive system, but
may also influence other equipment via ground loop. Such a leakage
current may result in malfunction of RCD and other equipment.
The higher the carrier frequency of drive is, the bigger the ground
leakage current would be. The longer the motor cables and the
bigger the parasitic capacitance are, the bigger the ground leakage
current would be. Therefore, the most immediate and effective
method for suppression of ground leakage current is to reduce
carrier frequency and minimize the length of motor cables.
2. The higher harmonics of line-to-line leakage current that passes
through between cables at output side of drive will accel the aging
of cables and may bring about malfunction of other equipment. The
higher the carrier frequency of drive is, the bigger the line-to-line
leakage current would be. The longer the motor cables and the bigger
the parasitic capacitance are, the bigger the line-to-line leakage
current would be. Therefore, the most immediate and effective
method for suppression of ground leakage current is to reduce
carrier requency and minimize the length of motor cable. Line-to-
line leakage current can also be effectively suppressed by mounting
additional output reactors.
3. For the SP110 serials, the models which power is less than 22kW
(including) can be removed RFI screws; the models which power is
greater than 30kW (including) can be set C14.50 = 0 to cut RFI filter
to reduce the leakage current;

- 40 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

3.5.5 Induction Voltage Suppression


The drive outputs pulse voltage which will form induction voltage in
the surface of the motor when the drive is not grounded. The induction
voltage can be reduced by connecting the drive's PE terminal to the
motor and closing RFI screws (models which power <= 22kW ) or
setting C14.50 = 1 (models which power >= 30kW).

HLP-SP110 Series Operating Manual - 41 -


HLP-SP110 Series

Chapter 4 Operation and Display Interface


4.1 LCP Digital Operator
Local Control Panel (LCP)can do the operation of parameters
modifications, status monitoring and drive control (start, stop), its
appearance is shown blow:

Screen

Incremental
Function LED potentiometer

Menu key Shift key

HAND key AUTO key


HAND LED AUTO LED

Off/Reset key OFF LED

1. State LED
The drive has three operating states: HAND control state, AUTO
control state and OFF state. The operating states are indicated by
HAND, AUTO and OFF Led.
HAND LED: The drive is in the HAND control state when it is
on. The frequency can be changed by tur ning the incremental
potentiometer. Push “HAND” key to set the drive in the HAND state.
OFF Led: The drive is in the OFF state when it is on. Push “OFF” key
to set the drive in the HAND state.
AUTOLED: The drive is in the AUTO state when it is on. In the AUTO
state, the drive is controlled by control terminals or communication.
Push “AUTO” key to set the drive in the AUTO state.

2. FunctionLed
FWD, REVLed: Indicates that the drive runs forwards or reverse.
Hz, A, RPM Led: Indicates the meaning of data displayed on the
screen.
Local remote running lights running lights, OFF LEDs, three LED
lights indicate.

- 42 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

3. Screen
There are 5 LED which can display reference, output frequency,
monitoring data and warning/alarm code.

4. Keys

Symbol Name Function

MENU Programming Enter or exit menu.


Select the displayed parameters in turn in
Shift the stop or running state; Select the digit to
be modified when modifying parameters.
Push it to set the drive in the HAND
HAND Hand
control state.
Stop the drive when it is in the running
OFF Off/Reset state and perform the reset operation when
it is in the fault state.
Push it to set the drive in the AUTO control
AUTO Auto
state.

Push the incremental potentiometer. Enter


Confirm
the menu or confirm the parameter setting.

5. Incremental Potentiometer
Increase/decrease data or parameter, clockwise to increase, counter-
clockwise to decrease.

4.2 Parameter Setting


Example: Set C03.10 [0] to 20.5:

Key-press LCP Display Action Description


Press key to display the first basic
C00.03
C00.03
Turn clockwise to select
C03.00
parameter group C03

HLP-SP110 Series Operating Manual - 43 -


HLP-SP110 Series

Key-press LCP Display Action Description

C03.00 Press key to shift to fractional part

Turn clockwise to select


C03.10
parameter C03.10

Press key show the first option of


[0]
C03.10

Press key to show the value of


0000
the first option of parameter C03.10
Turn clockwise to change the
000.5
f ractional part to 5

000.5 Press key to shif t to integral part

Press key to change the integral part


020.5
to 20

Press key to accept the change and


END
save it as 20.5

4.3 FWD/REV Status


Confirm the direction of the motor according to the set value, as shown in
the following table:
Reference: Running status Indicator Display

≥0 STOP

<0 STOP

- 44 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Reference: Running status Indicator Display

≥0 FWD

≥0 REV

<0 FWD

<0 REV

Note: A flash light denotes the status coming, Light on indicates the
current state, and light off means not in this state.
Example 1: The first line of the table indicates the drive is stop and the
reference is greater than or equal to 0, means the dirve at some
time in the future will run forward.
Example 2: The fourth line of the table represents the current drive is
reverse running, and the reference setting is greater than or equal
to 0, it means the drive at some time in the future will run forward.

4.4 Data Read-outs


Press key to change the display items on LCP while displaying

output frequency.

Display Items Key-press LCP Display Action Description


Show the output
Output Initial f requency
Frequency interface C16.13is50.0Hz, display
accuracy: 0.1

Show the reference


Reference (%) C16.01 is 50.000, display
accuracy: 0.001

HLP-SP110 Series Operating Manual - 45 -


HLP-SP110 Series

Display Items Key-press LCP Display Action Description

Show the motor


Motor Current current C16.14 is 9.00A,
display accuracy: 0.01

Show the motor


Motor Voltage voltage C16.12 is 380V,
display accuracy: 1

Show the motor speed


Motor Speed C16.05 is 1440rpm,
display accuracy:1

Show the DC Voltage


C16.30is
DC Voltage
540V,display
accuracy: 1

Show the Drive


Drive
temperature C16.34 is
temperature
45℃, display accuracy:1

Show the feedback


Feedback
valueC16.52 is 28.000,
Value
display accuracy: 0.001

Show counter A
Counter A C16.72 is 65535, display
accuracy:1

Show counter B
Counter B C16.72 is 65535, diaplay
accuracy : 1

- 46 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Display Items Key-press LCP Display Action Description

Show analog in VI
Analog in VI C16.62 is 10.00V, display
accuracy: 0.01

Show Analog in AI
Analog in AI C16.63 is 20.00mA,
display accuracy: 0.01

Show pulse
inputC16.68is
Pulse Input
50.000kHz, display
accuracy: 0.001

Show pulse output


Pulse Output (C16.69) is50000Hz,
display accuracy: 1

Note: The drive only monitor output frequency, reference and output
current reference by default. For monitoring other status
(DC voltage, etc.), please set the parameter C00.33 (refer to
instructions).

4.5 View Alarm Record


If the drive trips, fault code will be showed to illustrate the reason,the
drive will save the last 10 trip record.

Key-press LCP Display Action Description

Press key to display the first basic


C00.03
C00.03.

Turn clockwise to select par.


C15.00
group No. C15.

HLP-SP110 Series Operating Manual - 47 -


HLP-SP110 Series

Key-press LCP Display Action Description

C15.00 Press to select parameter number.

C15.30 Turn clockwise to select C15.30

Press to show the first option of


[0]
C15.30

Press to show the first fault


**
record.

Press to show the second fault

[1]
record, it can display up to ten recent
fault records in turn.

4.6 View State Parameter


By viewing the group 16th parameters can learn the current status of the
drive. For example: C16.60 indicators the current state of digital input
terminals.

Key-press LCP Display Action Description


Press to display the first basic
C00.03
parameter C00.03.

Turn clockwise to select Par.


C16.00
group No. C16

- 48 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Key-press LCP Display Action Description

C16.00 Press to select parameter No.

C16.60 Turn clockwise to select C16.60

Press to view the value in C16.60,

2
2 indicates status of FOR, DI1, DI2, DI3,
DI4 is 0, and status of REV is 1.

4.7 LED Display

HLP-SP110 Series Operating Manual - 49 -


HLP-SP110 Series

Chapter 5 Parameter Overview

Par.
Group Par. No. Name Range Unit Default

0: 50Hz
*C00.03 Regional Settings 0
1: 60Hz
0: Resume
1: Forced stop,
Operating State at
C00.04 ref=old 1
Power-up
2: Forced stop,
ref=0
*C00.06 Grid Type 0~122 *
1: Set-up 1
C00.10 Active Set-up 2: Set-up 2 1
9: Multi Set-up
1: Set-up 1
C00.11 Edit Set-up 1
Parameter Group 00: Operation/Display

2: Set-up 2
0: Not linked
*C00.12 Link Set-up 20
20: Linked
Custom Readout
C00.31 0.00 - 99999.00 0.00
Min. Value
Custom Readout
C00.32 0.00 - 99999.00 100.00
Max. Value
C00.33 LCP Display Option 0~4095 0
0: Disabled
C00.40 HAND Key Option 0
1: Enabled
0: Disabled
1: Enabled
C00.41 OFF Key Option 1
2: Enabled reset
only
0: Disabled
C00.42 AUTO Key Option 1
1: Enabled
0: Disabled
5: 5s
One Key Recovery
C00.46 10: 10s 5
Time
15: 15s
20: 20s
0: 0.1
LCP Potentiometer
C00.47 1: 1 0
Step
2: 10

- 50 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
0: No copy
Parameter Group 00: Operation/Display

1: Copy from set-up


1
*C00.51 Set-up Copy 2: Copy from set-up 0
2
9: Copy from fac-
tory setting
0: Disabled
C00.60 Set-up Locked 0
1: Enabled
C00.62 Time lock password 0~65535 0
Time lock password
C00.63 0~65535 0
value
TimePassword con-
C00.64 0~65535 0
firmation value
0: Speed open loop
3: Process closed
C01.00 Configuration Mode 0
loop
4: Torque open loop
Motor Control Prin- 0: V/F
*C01.01 1
ciple 1: VVC+
0: Constant torque
Torque Characteris- 1: Variable torque
*C01.03 1
tics 3: Auto Energy Op-
Par. Group01: Load/Motor

timization (AEO)
0: No function
Application Configu-
*C01.07 1: Water supply 0
ration Mode
function
*C01.20 Motor Power Motor dependant kW *
*C01.22 Motor Voltage 50~1000 V *
*C01.23 Motor Frequency 20~400 Hz *
*C01.24 Motor Current Motor dependant A *
*C01.25 Motor Speed 100~9999 rpm *
0: Disabled
1: Enable complete
Automatic Motor
*C01.29 AMA 0
Adaption (AMA)
2: Enable reduced
AMA
Stator Resistance
*C01.30 Motor dependant Ω 0.001
(Rs)
Stator Leakage Reac-
*C01.33 Motor dependant Ω 0.001
tance (X1)

HLP-SP110 Series Operating Manual - 51 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default

*C01.35 Main Reactance (Xh) Motor dependant Ω 0.01


*C01.39 Motor Poles 2~100 P 4
*C01.42 Motor Cable Length 0~150 m 50
Motor Magnetisation
C01.50 0~300 % 100
at Zero Speed
Min Speed Normal
C01.52 0.0~10.0 Hz 1.0
Magnetising
C01.55 V/F Characteristic-V 0.0~999.9 V *
C01.56 V/F Characteristic-F 0.0~400.0 Hz *
Low Speed Load
C01.60 0~199 % 100
Compensation
High Speed Load
C01.61 0~199 % 100
Compensation
C01.62 Slip Compensation -400~399 % 0
Slip Compensation
C01.63 0.05~5.00 s 0.30
Time Constant
Par. Group01: Load/Motor

Resonance Dampen-
C01.64 0~3000 % *
ing
Resonance Dampen-
C01.65 0.005~0.050 s 0.005
ing Time constant
C01.71 Start Delay 0.0~10.0 s 0.0
0: DC Hold
C01.72 Start Function 2
2: Coast
0: Disabled
*C01.73 Flying Start 0
1: Enabled
C01.75 Min. Start Frequency 0.00~10.00 Hz 0.00
C01.76 Jump Frequency 0.0~20.0 Hz 0.0
0: Coast
C01.80 Function at Stop 0
1: DC Hold
Min Speed for Func-
C01.82 0.0~400.0 Hz 0.0
tion at Stop
0: No protection
1: Thermistor warn-
Motor Thermal ing
C01.90 0
Protection 2: Thermistor trip
3: ETR warning
4: ETR trip
Thermistor Resource 0: None
*C01.93 0
1: Terminal VI

- 52 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default

C02.00 DC Hold Current 0~150 % 50


C02.01 DC Brake Current 0~150 % 50
C02.02 DC Braking Time 0.0~60.0 s 10.0
DC Brake Cut in
C02.04 0.0~400.0 % 0.0
Speed
Motor Demagnetiza-
C02.08 0~100 % 100
tion
Par. Group 02: Brake Function

0: Off
C02.10 Brake Function 0
2: AC brake
Over-voltage Control
C02.15 Grid type dependant V *
Threshold Voltage
AC Brake, Max Cur-
C02.16 0~150 % 100
rent
0: Disabled
C02.17 Over-voltage Control 2: Mode 1 3
3: Mode 2
Over-voltage Control
C02.18 0.01~0.10 s 0.05
Integral Time
Over-voltage Control
C02.19 0~200 % 100
Proportional Gain
Release Brake Cur-
C02.20 0.00~1200.00 A 0.00
rent
C02.22 Activate Brake Speed0.0~400.0 Hz 0.0
0: 0~Max
C03.00 Reference Range 0.000
1: -Max~+Max
C03.03 Maximum Reference C03.02~4999.000 50.000
Par. Group 03: Reference/Ramps

0: Presetreference +
Reference source1,
Main Reference
C03.07 2, 3 0
Calculation
1: Presetreference
priority
C03.10 PresetReference -100.00~100.00 % 0.00
C03.11 Jog speed 0.0~400.0 Hz 5.0
Catch up/Slow down
C03.12 0.00~100.00 % 0.00
Value
Speed Up/Down
C03.13 0.01~50.00 Hz 0.10
Value
Preset RelativeRefer-
C03.14 -100.00~100.00 % 0.00
ence

HLP-SP110 Series Operating Manual - 53 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default

C03.15 Reference Source1 0: No function 1


C03.16 Reference Source2 1: Terminal VI 0
2: Terminal AI
C03.17 Reference Source3 11
11: Local bus
Relative Reference 21: LCP potentiom-
C03.18 0
Source eter
0: No function
Speed Up/Down
C03.19 1: Stop save 0
Value Store
2: Power down save
0: Linear
C03.40 Ramp 1 Type 0
2: S ramp
Ramp 1 Ramp Up
Par. Group 03: Reference/Ramps

C03.41 0.05~3600.00 s *
Time
Ramp 1 Ramp Down
C03.42 0.05~3600.00 s *
Time
0: Linear
C03.50 Ramp 2 Type 0
2: S ramp
Ramp 2 Ramp Up
C03.51 0.05~3600.00 s *
Time
Ramp 2 Ramp Down
C03.52 0.05~3600.00 s *
Time
0: Linear
C03.60 Ramp 3 Type 0
2: S ramp
Ramp 3 Ramp Up
C03.61 0.05~3600.00 s *
Time
Ramp 3 Ramp Down
C03.62 0.05~3600.00 s *
Time
0: Linear
C03.70 Ramp 4 Type 0
2: S ramp
Ramp 4 Ramp Up
C03.71 0.05~3600.00 s *
Time
Ramp 4 Ramp Down
C03.72 0.05~3600.00 s *
Time
C03.80 Jog Ramp Time 0.05~3600.00 s *
Limits/Warnings
Par. Group 04:

0: Clockwise
Motor Speed Direc- 1: Counter clock-
*C04.10 2
tion wise
2: Both directions

- 54 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
Motor Speed Low
*C04.12 0.0~C04.14 Hz 0.0
Limit
Motor Speed High-
*C04.14 C04.12~C04.19 Hz 50.0
Limit
C04.18 Current Limit 0~300 % 120
Max Output Frequen-
*C04.19 0.0~400.0 Hz 50.0
cy
0: No function
1: Terminal VI
Frequency Upper 2: Terminal AI
*C04.21 0
Limit Source 11: Local bus
21: LCP potentiom-
eter
0: Disable
1: Counter A save
Par. Group 04: Limits/Warnings

Counter Store at
C04.42 2: Counter B save 0
Power down
3: Both counter A
and B save
Warning Current
C04.50 0.00~I max A 0.00
Low
Warning Current
C04.51 0.00~I max A *
High
Warning Frequency
C04.52 0.0~400.0 Hz 0.0
Low
Warning Frequency-
C04.53 0.1~400.0 Hz 65.0
High
Warning Reference
C04.54 -4999.000~4999.000 0.000
Low
Warning Reference
C04.55 -4999.000~4999.000 50.000
High
Warning Feedback
C04.56 -4999.000~4999.000 0.000
Low
Warning Feedback
C04.57 -4999.000~4999.000 50.000
High
Missing Motor Phase 0: Disable
*C04.58 1
Function 1: Enable
Current limit warn- 0: warning off
C04.59 1
ing fucntion 1: warning on
C04.61 Bypass Speed From 0.0~400.0 Hz 0.0
C04.63 Bypass Speed to 0.0~400.0 Hz 0.0

HLP-SP110 Series Operating Manual - 55 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
C05.04 DI Filter Time 2~16 ms 4
C05.05 DI terminal logic function 0 ~ 255 0
DO/RL terminal logic
C05.06 0 ~ 255 0
function
0: invalid
1: freeze output frequency
DI external fault function 2: stop
C05.09 3: jog frequency 0
4: max frequency
5: stop and alarm
C05.10 Terminal FOR 0: No operation 8
1: Reset
C05.11 Terminal REV 2: Coast inverse 11
C05.12 Terminal DI1 3: Coast and reset nverse 15
6: Stop inverse
C05.13 Terminal DI2 8: Start 16
9: Latched start
C05.14 Terminal DI3 10: Reversing 17
11: Start reversing
12: Enable start
forward only
13: Enable start reverse only
14: Jog
15: Preset ref. bit0
Par. Group 05: Digital In/Out

16: Preset ref. bit1


17: Preset ref. bit2
18: Preset ref. bit3
19: Freeze reference
20: Freeze output
21: Speed up
22: Speed down
23: Set-up select
28: Catch up
29: Slow down
34: Ramp bit0
35: Ramp bit1
37: Latched eversing
42: Coast; 46: Stop
60: Counter A
62: Reset counter A
63: Counter B
65: Reset counter B
110: invalid closed-loop
160: multi pump control,
pump 1 enable terminal
161: multi pump control:
pump 2 enable terminal
162: multi pump control:
pump 3 enable terminal
163: multi pump control:
pump 4enable terminal
164: multi pump control:
pump 5enable terminal
165: multi pump control:
pump 6 enable terminal
171: water supply
function: the speed of
the open loop speed
running
signal, taking the
VI channel setting
value as the target
frequency value

- 56 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default

0: No operation
1: Drive ready
3: Remote control
ready
4: Drive running/
No warning
5: Drive running
7: Run in range/No
warning
8: Run on
reference/No
warning
9: Alarm
10: Alarm or
warning
12: Out of current
range
13: Below current
low
14: Above current
high
15: Out of
frequency range
Par. Group 05: Digital In/Out

16: Below
frequency low
17: Above requency
high; 18: Out of
feedback range
C05.40 Relay Function 19: Below feedback 5, 9
low; 20: Above
feedback high
21: Thermal warning
22: Ready
23: Remote ready
24: Ready, voltage
OK
25: Reverse;26: Bus
OK
32: Mech. brake
control
36: Control word
bit11
37: Control word
bit12
40: Out of reference
range, reference is
outside the range set
in
C04.54 and C04.55;
41: Below reference
low, reference is
lower than set in
C04.54;
42: Above reference
high, reference is
higher than set in
C04.55;

HLP-SP110 Series Operating Manual - 57 -


HLP-SP110 Series

Par.
Par. No. NameName Range Unit Default
Group
51: Drive in HANDstate;
52: Drive in AUTOstate;
56: Drive in HANDstate;
57: Drive in AUTOstate;
60: Comparator 0,
using a simple PLC, the
results of comparator 0;
61: Comparator 1,
using a simple PLC, the
results of comparator 1;
62: Comparator 2,
using a simple PLC, the
results of comparator 2;
63: Comparator 3,
using a simple PLC, the
results of comparator 3;
70: Logic rule 0, using a
simple PLC, the results
of logic rule 0;
71: Logic rule 1, using a
simple PLC, the results
Par. Group 05: Digital In/Out

of logic rule 1;
72: Logic rule 2, using a
simple PLC, the results
of logic rule 2;
C05.40 Relay Function 73: Logic rule 3, using a
simple PLC, the results 5,9
of logic rule 3;
80: Simple PLC digital
rutput 1, only active for
DO1;
81: Simple PLC digital
output 2, only active for
DO2;
82: Simple PLC relay 1,
only active for relay 1;
83: Simple PLC relay 2,
only active for relay 2;
84: Simple PLC relay 2,
only active for relay 3;
160: Water supply: low
voltage alarm control
161: Water supply: Over
voltage alarm control
162: Water supply:
Sleep
163: Water supply:Belt
breaking signal
164: Water supply:No
inverter available
192: Water supply:Relay
control

- 58 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
FA/FB/FC;
KA1/KB1;
KA2/KB2;
KA3/KB3;
C05.41[x] Closed relay delay KA4/KB4; S 0.00
Par. Group 05: Digital In/Out

KA5/KB5
0~5:Correspond to
Range:
0.00~600.00
FA/FB/FC;
KA1/KB1;
KA2/KB2;
KA3/KB3;
C05.42[x] Open relay delay KA4/KB4; S 0.00
KA5/KB5
0~5:Correspond to
Range:
0.00~600.00
Live Zero Timeout-
C06.00 1~99 s 10
Time
0: Off
1: Freeze output
Live Zero Timeout 2: Stop
C06.01 0
Function 3: Jogging
4: Max. speed
5: Stop and trip
Par.Group 06: AnalogIn/Out

Te r m i n a l V I L o w 0.00~9.99
C06.10 V 0.07
Voltage
Terminal VI High
C06.11 0.10~10.00 V 10.00
Voltage
Te r m i n a l V I L o w 0.00~19.99
C06.12 mA 0.14
Current
Terminal VI High
C06.13 0.01~20.00 mA 20.00
Current
Te r m i n a l V I L o w
C06.14 -4999.000~4999.000 0.000
Ref./Feedb. Value
Terminal VI High
C06.15 -4999.000~4999.000 50.000
Ref./Feedb. Value
Te r m i n al V I Fi lt e r 0.01~10.00
C06.16 s 0.010
Time
Terminal VI Zero 0.0~20.00 V/
C06.18 0.00
Dead Band mA

HLP-SP110 Series Operating Manual - 59 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
0: Voltage mode
C06.19 Terminal VI Mode 0
1: Current mode
Te r m i n a l A I L o w 0.00~9.99
C06.20 V 0.07
Voltage
Te r m i n a l A I H i g h 0.10~10.00
C06.21 V 10.00
Voltage
Te r m i n a l A I L o w 0.00~19.99
C06.22 mA 4.00
Current
Te r m i n a l A I H i g h 0.10~20.00
C06.23 mA 20.00
Current
Te r m i n a l A I L o w -4999.000~4999.000
C06.24 0.000
Ref./Feedb. Value
Te r m i n a l A I H i g h -4999.000~4999.000
C06.25 50.000
Ref./Feedb. Value
C06.26 Terminal AI Filter Time0.01~10.00 s 0.010
V/
C06.28 Te r m i n a l A I Z e r o 0.0~20.00 0.00
Dead Band mA
0: Voltage mode
C06.29 Terminal AI Mode 1: Current mode 1
Par.Group 06: AnalogIn/Out

2:Resistance signal
C06.30 Analog AI minimum 0~400 Ω 0.0
input resistor
C06.31 Analog maximum AI 0~600 Ω 400.0
input resistor
0: 0-20mA
C06.70 Terminal VO Mode 1: 4-20mA 3
3: 0-10V
C06.71 Terminal VO Analog 0~23 0
Output
C06.73 Terminal VO Output 0.00~200.00 % 0.00
Min. Scale
C06.74 Terminal VO Output 0.00~200.00 % 100.00
Max. Scale
Te r m i n a l VO m i n 0.00~C06.76
C06.75 output 0
Voltage mode:
C06.76 Te r m i n a l VO m a x C06.75~10.00 10.00
output Current mode:
C06.75~20.00
C06.81 LCP Pot.Min. Ref. -4999.000~4999.000 0.000
C06.82 LCP Pot.Max. Ref. -4999.000~4999.000 50.000
C06.90 Terminal AO Mode 0: 0-20mA 0
1: 4-20mA
Terminal AO Analog
C06.91 Output 0~23 0
Terminal AO Output
C06.93 Min. Scale 0.00~200.00 % 0.00

C06.94 Terminal AO Output 0.00~200.00 % 100.00


Max. Scale

- 60 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
Te r m i n a l AO m i n 0.00~C06.96
C06.95 0
output
Te r m i n a l AO m a x Current
C06.96 20.00
output mode:C06.95~20.00
Torque PI Propor-
C07.12 0~500 % 100
tional Gain
Torque PI Integration
C07.13 0.002~2.000 s 0.020
Time
0: No function
Process PID Feed- 1: Terminal VI
C07.20 2: Terminal AI 2
back Source 8: Pulse input DI4
11: Local bus
Process PI Normal/ 0: Normal
C07.30 0
Inverse 1: Inverse
Process PI Anti 0: Disable
C07.31 1
Windup 1: Enable
C07.32 Process PIStart 0.0~200.0 Hz 0.0
Process PI Propor-
C07.33 0.00~10.00 1.2
tional Gain
Par. Group 07: Controllers

Process PID Integral


C07.34 0.10~9999.00 s 5
Time
Process PID Differ-
C07.35 0.00~10.00 s 0.02
entiation Time
C07.36 PID differential limit 1.00~50.00 s 5.00
Process PID Feed
C07.38 0~400 % 0
Forward Factor
On Reference Band-
C07.39 0~200 % 0.1
width
Process PID Output
C07.41 -100~100 % 0.00
Low
Process PID Output
C07.42 -100~100 % 100.00
High
0:set valu   1:VI
Feed forward factor
C07.45 2:AI  11: Local bus 0
source
21:LCP
Feed forward factor 0:Positive logic
C07.46 0
control mode 1:Anti logic
C07.50 I Integral limit 100.00~100.00 % 0.00
C07.51 I Integral term limit 100.00~100.00 % 100.00
0:Mode0
Bandwidth control
C07.55 1:Mode1 0
mode
2:Mode2

HLP-SP110 Series Operating Manual - 61 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
0: Digital and con-
trol word
C08.01 Control Site 1: Digital only 0
2: Control word
only
Control Word Selec- 0: Disable
C08.02 1
tion 1: Enable
Control Word Time-
C08.03 0.1~6500.0 s 1.0
out Time
0: Off
1: Freeze output
Control Word Time- 2: Stop
C08.04 0
out Function 3: Jogging
4: Max. speed
5: Stop and trip
Reset Control Word 0: Do not reset
C08.06 0
Par. Group 08: Communiction

Timeout 1: Do reset
C08.20 Diagnostic function 0:off; 1:start 1
0: FC
C08.30 Protocol 2: Modbus RTU 0
6: Modbus ASCII
C08.31 Address 0~247 1
0: 2400
1: 4800
2: 9600
3: 19200
bit/s
C08.32 Baud Rate 4: 38400 2
5: 57600
6: 76800
7: 115200
8~9: Reserved
0: Even parity (1
stop bit)
1: Odd parity (1 stop
bit)
C08.33 Parity/Stop Bits 2
2: No parity (1 stop
bit)
3: No parity (2 stop
bit)
C08.35 Min. Response Delay 0.000~0.500 s 0.002
C08.36 Max. Response Delay0.010~10.000 s 5.000

- 62 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
0: Normal
1: Only response
C08.38 Message Response 0
exception message
Par. Group 08: Communiction

2: Not response
0: Not saved at
Modbus Parameter power down
C08.39 0
Write Store 1: Saved at power
down
C08.50 Coasting Select 3
C08.53 Start Select 0: Digital input 3
C08.54 Reversing Select 1: Bus 3
2: Logic AND
C08.55 Set-up Select 3
3: Logic OR
Preset Reference
C08.56 3
Select
0: Off
C13.00 Simple PLC Mode 1: Order execution 0
2: Parallel execution
0: False
1: True
2: Running
3: In current range-
No warning
4: On reference-No
Par. Group 13: SimplePLC

warning
7: Out of current
range
8: Below current
low
C13.01 Start Event 9: Above current 39
high
10: Out of frequency
range
11: Below frequency
low
12: Above frequen-
cy high
13: Out of feedback
range
14: Below feedback
low

HLP-SP110 Series Operating Manual - 63 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
15: Above feedback
high
16: Thermal warn-
ing
17: Mains out of
range
18: Reversing
19: Warning
20: Alarm (trip)
21: Alarm (trip lock)
22: Comparator 0
23: Comparator 1
24: Comparator 2
25: Comparator 3
26: Logic rule 0
27: Logic rule 1
28: Logic rule 2
29: Logic rule 3
30: Simple PLC
Par. Group 13: SimplePLC

time-out 0
31: Simple PLC
time-out 1
32: Simple PLC
time-out 2
33: Terminal FOR
34: Terminal REV
35: Terminal DI1
36: Terminal DI2
37: Terminal DI3
38: Terminal DI4
39: Start command
40: Drive stopped
50: Simple PLC
time-out 3
51: Simple PLC
time-out 4
52: Simple PLC
time-out 5
53: Simple PLC
time-out 6
54: Simple PLC
time-out 7
C13.02 Stop Event 0~54 40
0: Do not reset
C13.03 Reset Simple PLC 0
1: Do reset

- 64 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default

0: No function
1: Power down save
C13.04 Simple PLCStore 2: Stop save 0
3: Both power down
and stop save
0: Disabled
1: Reference
2: Feedback
3: Motor speed [Hz]
4: Motor current [A]
6: Motor power
[kW]
7: Motor Voltage
C13.10 Comparator Operand 0
[V]
12: Terminal VI
input
Par. Group 13: SimplePLC

13: Terminal AI
input
20: Fault number
30: Counter A
31: Counter B
0: Less than
C13.11 Comparator Operator 1: Approx. Equal 1
2: Greater than
C13.12 Comparator Value -9999.0~9999.0 0.0
C13.20 Simple PLC Timer 0.00~3600.00 s 0.00
Logic Rule Boolean The same as
C13.40 0
1 C13.01’s
0: Disabled
1: AND
2: OR
3: AND NOT
Logic Rule Operator
C13.41 4: OR NOT 0
1
5: NOT AND
6: NOT OR
7: NOT AND NOT
8: NOT OR NOT
Logic Rule Boolean The same as
C13.42 0
2 C13.01’s

HLP-SP110 Series Operating Manual - 65 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
Logic Rule Operator The same as
C13.43 0
2 C13.41’s
Logic Rule Boolean The same as
C13.44 0
3 C13.01’s
The same as
C13.51 Simple PLC Event 0
C13.01’s
0: Disabled
1: No action
2: Select set-up 1
3: Select set-up 2
10: Select preset ref 0
11: Select preset ref 1
12: Select preset ref 2
13: Select preset ref 3
14: Select preset ref 4
15: Select preset ref 5
Par. Group 13: SimplePLC

16: Select preset ref 6


17: Select preset ref 7
18: Select ramp 1
19: Select ramp 2
20: Select ramp 3
21: Select ramp 4
22: Run
C13.52 Simple PLC Action 23: Run reverse 0
24: Stop
27: Coast
28: Freeze output
29: Start timer 0
30: Start timer 1
31: Start timer 2
32: Set terminal
DO1 low
33: Set terminal
DO2 low
34: Set relay 1 low
35: Set relay 2 low
38: Set terminal
DO1 high
39: Set terminal
DO2 high
40: Set relay 1 high

- 66 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default

41: Set relay 2 high


50: Select preset ref 8
51: Select preset ref 9
52: Select preset ref 10
Par. Group 13: SimplePLC

53: Select preset ref 11


54: Select preset ref 12
55: Select preset ref 13
56: Select preset ref 14
57: Select preset ref 15
60: Reset counter A
61: Reset counter B
65: Start timer 3
66: Start timer 4
67: Start timer 5
68: Start timer 6
69: Start timer 7
2~6: 2~6kHz
7: 8kHz
C14.01 Switching Frequency 8: 10kHz kHz 5
9: 12kHz
10: 16kHz
0: Off
*C14.03 Overmodulation 1
1: On
Par. Group 14: SpecialFunctions

C14.08 Damping Gain Factor0~200 % 96


0: Trip (Low sensi-
tivity)
1: Warning (Low
sensitivity)
2: Disabled
Function at Mains
C14.12 4: Warning (Middle 0
Imbanlance
sensitivity)
5: Trip (Middle
sensitivity)
6: Trip (High sensi-
tivity)
0: Disable
C14.16 Low Voltage Mode 0
1: Enable
Automatic Voltage 0: Disable
C14.17 1
Regulation 1: Enable

HLP-SP110 Series Operating Manual - 67 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
Delay Time of Auto
C14.18 RestartWhen Power 0.0~3600.0 s 0.0
up Again
0: Manual reset
1~10: Auto reset
1-10 times
C14.20 Reset Mode 0
11: Auto reset 15 times
12: Auto reset 12 times
13: Infinite auto reset
Automatic Restart
C14.21 0~600 s 10
Time
0: Normal operation
2: Initialization
3: Backup user set-
C14.22 Operation Mode 0
tings
4: Recover user set-
Par. Group 14: SpecialFunctions

tings
0: Disable
C14.23 Trip lock 1
1: Enable
Current limit alarm
14.24 0~60 s 60
delay
Torque limit alarm
14.25 0~60 s 60
delay
0: Trip
C14.27 Action at Drive Fault 0
1: Warning
Current Controller 1
C14.30 0~300 % 100
Proportional Gain
Current Controller
C14.31 0.005~2.000 s 0.020
1Integration Time
Current Controller
C14.32 2.0~100.0 ms *
Filter Time
Current Controller 2
C14.33 0~300 % 0
Proportional Gain
Current Controller
C14.34 0.001~2.000 s 0.020
2Integration Time
*C14.40 VT Level 40~90 % 90
AEO Min. Magneti-
*C14.41 40~75 % 66
sation
0: Off
*C14.50 RFI Filter Selection 1: On 1
2: Reserved
0: Off
*C14.51 DC Link Compensation 0
1: On

- 68 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default

C15.00 Operating Days 0~9999 d


C15.01 Running Hours 0~60000 h
C15.02 kWh Counter 0~65535 kWh
Par. Group 15: DriveInformation

C15.03 Power Up’s 0~2147483647


C15.04 Over Temperatures 0~65535
C15.05 Over Voltages 0~65535
0: Do not reset
C15.06 Reset kWh Counter 0
1: Do reset
Reset Running Hours 0: Do not reset
C15.07 0
Counter 1: Do reset
C15.30 Alarm Code 0~255
C15.31 Internal Fault Reason -32767~32767
C15.38 Warning Code 0~255
C15.43 Software Version
C16.00 Control Word 0~65535
C16.01 Reference -4999.000~4999.000
C16.02 Reference -200.0~200.0 %
C16.03 Status Word 0~65535
0: Set-up 1
C16.04 Active Set-up 1: Set-up 2
2: Multi Set-up
Par. Group 16: DataReadouts

C16.05 Motor Speed 0 - 15000 rpm


C16.09 Custom Readout 0.00 - 9999.00
C16.10 Output Power 0.000 ~ 1000.000 kW
C16.11 Output Power 0.000 ~ 1000.000 hp
C16.12 Motor Voltage 0~65535 V
C16.13 Output Frequency 0.0~400.0 Hz
C16.14 Output Current 0.00~655.35 A
C16.15 Output Frequency 0.0~200.0 %
C16.16 Output Torque -65535.0~65535.0 Nm
C16.18 Motor Thermal 0~100 %
C16.30 DC Link Voltage 0~65535 V
C16.34 IGBT Temperature 0~65535 ℃
C16.35 Drive Thermal 0~255 %

HLP-SP110 Series Operating Manual - 69 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
Drive NominalCur-
C16.36 0.00~1200.00 A
rent
C16.37 Drive Max. Current 0.00~2400.00 A

C16.38 Simple PLC State 0~255


Powe r Boa rd Te m-
C16.48 -128~127 ℃
perature
Rectif ier Tempera-
C16.49 -128~127 ℃
ture
C16.50 Main Reference -200.0~200.0 %

C16.52 Feedback -4999.000~4999.000

C16.60 Digital Input 0~65535


0: 0~20mA
C16.61 Terminal VI Setting
1: 0~10V
Par. Group 16: DataReadouts

V/
C16.62 Analog Input VI 0.00~20.00
mA
0: 0~20mA
C16.63 Terminal AI Setting
1: 0~10V
V/
C16.64 Analog Input AI 0.00~20.00
mA
V/
C16.65 Analog Output VO 0.00~20.00
mA
C16.66 Digital Output 0~255

C16.71 Relay Output 0~65535

C16.72 Counter A 0~2147483647

C16.73 Counter B 0~2147483647

C16.78 Analog Output AO 0.00~20.00 mA


Communication
C16.86 -32768~32767
Reference
C16.90 Alarm Word 1 0~0xFFFFFFFFUL

C16.91 Alarm Word 2 0~0xFFFFFFFFUL

C16.92 Warning Word 1 0~0xFFFFFFFFUL

C16.93 Warning Word 2 0~0xFFFFFFFFUL

- 70 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default
1:Mode1
C25.01 Pump type 2:Mode2 3
3:Mode3
0:Use enable
C25.02 Pump enable signal 1:Do not use to en- 0
able
C25.03 Pump number 0~5 0
C25.09 Pump status display 0~65535 0
Built in acceleration
C25.13 0.00~3600.00 S 0.00
time
Internal deceleration
C25.14 0.00~3600.00 S 0.00
time
C25.20 Low frequency set 1 0.0~400.0 HZ 25.0
Low frequency dura-
C25.21 0.00~3600.00 HZ 25.0
tion
C25.22 Low frequency set 2 0.0~400.0 HZ 25.0
Par. Group 25: Wobble

C25.23 Low frequency set 3 0.0~400.0 HZ 25.0


C25.25 High frequency set 1 0.0~400.0 HZ 25.0
High frequency dura-
C25.26 0.00~3600.00 S 100.0
tion
C25.27 High frequency set 2 0.0~400.0 HZ 50.0
C25.28 High frequency set 3 0.0~400.0 HZ 50.0
Under pressure alarm
C25.30 0.0~101.0 % 0.0
pressure
Under pressure alarm
C25.31 0.00~3600.00 S 10.0
duration
Under pressure alarm
C25.32 0.0~101.0 % 0.1
reset value
Under pressure alarm
C25.33 0.00~3600.00 S 10.0
reset time
Over pressure alarm
C25.34 0.0~200.0 % 199.0
pressure
Over pressure alarm
C25.35 0.00~3600.00 S 10.0
duration
Over pressure alarm
C25.36 0.0 - 200.0 % 199.0
reset value
Over pressure alarm
C25.37 0.00 ~ 3600.00 S 10.0
reset time
C25.40 Pump lock time 0.00~3600.00 S 1.0
The auxiliary pump
C25.42 0.00~3600.00 H
running time

HLP-SP110 Series Operating Manual - 71 -


HLP-SP110 Series

Par.
Group Par. No. Name Range Unit Default

Change pump fre-


C25.43 0.0~400.0 HZ 50.0
quency
C25.45 Start delay time 0.00~3600.00 S 1.0
Automatic pump time
C25.46 0~6000.0 H
display
Multi pump control
C25.48 0~65535
state display
C25.49 Relay status display 0~65535
0:Invalid
C25.50 Sleep mode 0
2:Effective
C25.51 Sleep pressure level 0.0~150.0 % 95%
Sleep pressure dura-
C25.52 0.0~300.0 S 20.0
tion
Par. Group 25: Wobble

C25.53 Sleep frequency 0.0~400.0 HZ 20.0


Sleep frequency
C25.54 0.0~300.0 S 20.0
duration
Wake up pressure
C25.57 0.0~150.0 % 80%
level
0:Disabled
Belt breakage detec-
C25.85 1:warning 0
tion
2:jump off
The frequency of belt
C25.86 breakage detection 0.0~400.0 HZ 0.5
value
The belt breakage
C25.87 detecting current 0.0~3000.0 A 0.0
value
0:Greater than
The belt breaking
C25.87 set values
C25.88 current direction A 0
1:Less than C25.87
detection
set value
Belt breakage detec-
C25.89 0.0~600.0 S 20
tion: time delay
Note: Reference signed with “*”inPar. No. column means this parameter can’t
be modified when the motor is running. In factory setting column, “*”
means the default setting for this parameter is determined by the drive
type.

- 72 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Chapter 6 Parameter Description


6.1 Group 00: Operation/Display
C00.0* Basic Settings

Par. No. Name Range Unit Default


Regional 0: 50Hz
*C00.03 0
Settings 1: 60Hz

This parameter is used to select motor frequency default value according


to different regions.
0: 50Hz, Motor frequency default value is 50 Hz, see C01.23;
1: 60Hz, Motor frequency default value is 60 Hz, see C01.23;
Attention: This parameter can not be adjusted when motor is running.
Change this parameter may result in changes in the value of
the following parameters: C01.23, C01.25, C01.39, C01.56,
C01.30, C01.33, C01.35.

Par. No. Name Range Unit Default


Operating 0: Resume
C00.04 State at 1: Forced stop, ref=old 1
Power-up 2: Forced stop, ref=0
Selects the operating mode upon reconnection of the drive to mains
voltage after power down in Hand operation mode.
0: Resume, restarts the drive maintaining the same local reference
and the same start/stop settings as before the drive was powered down.
1: Forced stop, ref= old, restarts the drive with a saved local
reference, after mains voltage reappears and after pressing HAND key.
2: Forced stop, ref=0, resets the local reference to 0 upon restarting
the drive.
Attention: This parameter is only active in Hand operation mode.

Par. No. Name Range Unit Default


*C00.06 Grid Type 10~122 *
Selects the grid type. Output frequency and voltage will be changed
according to the grid type.

10: 380-440V/50Hz/IT-Grid
11: 380-440V/50Hz/IT-Delta
12: 380-440V/50Hz
20: 440-480V/50Hz/IT-Grid

HLP-SP110 Series Operating Manual - 73 -


HLP-SP110 Series

21: 440-480V/50Hz/IT-Delta
22: 440-480V/50Hz
100: 200-240V/60Hz/IT-Grid
101: 200-240V/60Hz/IT-Delta
102: 220-240V/60Hz
110: 380-440V/60HZ/IT-Grid
111: 380-440V/60Hz/IT-Delta
112: 380-440V/60Hz
120: 440-480V/60Hz/IT-Grid
121: 440-480V/60Hz/IT-Delta
122: 440-480V/60Hz

C00.1* Set-up Operations

Define and control the individual parameter setups.


T he d r ive h a s t wo pa r a met e r set up s t h at ca n b e p rog r a m me d
independently of each other. This makes the drive very flexible and able
to solve advanced control functionality problems, often saving the cost
of external control equipment. For example these can be used to program
the drive to operate according to one control scheme in one setup (e.g.
motor 1 for horizontal movement) and another control scheme in another
setup (e.g. motor 2 for vertical movement). Alternatively they can be
used by an OEM machine builder to identically program all their factory
fitted drives for different machine types within a range to have the same
parameters and then during production/commissioning simply select a
specific setup depending on which machine the drive is installed on.

Par. No. Name Range Unit Default


1: Set-up 1
C00.10 Active Set-up 2: Set-up 2 1
9: Multi Set-up

Selects the set-ups to control the drive functions.


1: Set-up 1, Set-up 1 to Set-up 2 are the two separate parameter set-
ups within which all parameters can be programmed.
2: Set-up 2
9: Multi Set-up, two set-ups can be changed each other via digital
input or communication commands.

- 74 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par. No. Name Range Unit Default


1: Set-up 1
C00.11 Edit Set-up 1
2: Set-up 2

Selects the set-up to be edited during operation, either the active set-up or
one of the inactive set-ups.

Par. No. Name Range Unit Default


0: Not linked
C00.12 Link Set-up 20
20: Linked

0: Not linked, parameters between two set-ups can notbe changed


each other while the motor is running;
20: Linked, parameters between two set-ups can be changed each
other while the motor is running viadigital input or communication
commands. But this facility is best for the same motor, else the link will
synchronize the parameters that can not be changed while the motor is
running (mainly motor parameters).

C00.3* LCP Custom Readout

Par. No. Name Range Unit Default


Custom Readout Min.
C00.31 0.00 ~ 99999.00 0.00
Value
Custom Readout Max.
C00.32 0.00 ~ 99999.00 100.00
Value

It is possible to customize a readout value in the drive. Custom Readout


Value is linear proportional to speed, it is stored in parameter C16.09.
The calculation of Custom Readout Value (C16.09) is shown below:
C16.09 = (C00.32 - C00.31) × C16.13 ÷ C04.14 + C00.31

Par. No. Name Range Unit Default


C00.33 LCP Display Option 0~4095 0

The LCP is fixed to display the output frequency、reference and motor


current (switch by ◄ key). This parameter is used to show another 11
basic operating states of the drive, each states corresponds to a binary
code : “1” means display the item, “0” means does not display the item.
For example, if you want to display the states of the temperature and the
terminal VI on LCP. Transform the binary code to decimal digit,
C00.33=1×23+1×27=136.

HLP-SP110 Series Operating Manual - 75 -


HLP-SP110 Series

Bit Bit
Bit 9 Bit 8 Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
11 10
Custom Readout

Pulse Output

Pulse Input

AI

VI

Counter B

Counter A

Feedback Value

Temperature

DC-Voltage

Motor Speed

Motor Voltage
0 0 0 0 1 0 0 0 1 0 0 0

C00.4* LCP Keypad


Enable, disable individual keys on the LCP.

Par. No. Name Range Unit Default


0: Disabled
C00.40 HAND Key Option 0
1: Enabled

0: Disabled, No effect when HAND key is pressed. Select [0]


Disabled to avoid accidental start of the drive in Hand operation mode;
1: Enabled, HAND key is functional;

Par. No. Name Range Unit Default


0: Disabled
C00.41 OFF Key Option 1: Enabled 1
2: Enabled reset only

0: Disabled, avoids accidental stop of the drive;


1: Enabled, OFF key stop signal and reset of any fault;
2: Enabled reset only, reset only (fault), stop (off ) function is
disabled;

Par. No. Name Range Unit Default


AUTO Key 0: Disabled
C00.42 1
Option 1: Enabled

0: Disabled, avoids accidental start of the drive in AUTO operation


mode;
1: Enabled, AUTO key is functional;

- 76 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par. No. Name Range Unit Default


0: Disabled
5: 5s
One Key Recovery
C00.46 10: 10s 5
Time
15: 15s
20: 20s

“One Key Recovery”is that user can press OFF key to recover the backup
settings if the settings have been backuped. If the settings have not been
backuped, this function is disabled.
One key Recovery Time is used to determine how many seconds should
OFF key pressed to recover the backup settings, it is set to 0 to disable
one key recovery function.
Note: If an alarm happens, press OFF key will reset alarm first.

Par. No. Name Range Unit Default


LCP 0: 0.1
C00.47 Potentiometer 1: 1 0
Step 2: 10

This parameter determines the reference value increase or decrease when


the LCP potentiometer rotates.

C00.5* Copy/Save

Par. No. Name Range Unit Default


0: No copy
1: Copy from set-up 1
C00.51 Set-up Copy 2: Copy from set-up 2 0
9: Copy from factory
setting

0: No copy;
1: Copy from set-up 1, Copies all parameters in the Set-up 1 to the
edit set-up (defined in C00.11);
2: Copy from set-up 2, Copies all parameters in the Set-up 2 to the
edit set-up (defined in C00.11);
9: Copy from factory setting, Copies factory setting to the edit set-
up (defined in C00.11);
Attention: Whenselected set-up is thesame to the editset-up,copy
function doesn’t work; bothLCP and parameter database are locked while
copying.

HLP-SP110 Series Operating Manual - 77 -


HLP-SP110 Series

C00.6* Protection

Par. No. Name Range Unit Default


0: Disabled
C00.60 Set-up Locked 0
1: Enabled

0: Disabled
1: Enabled, prevent unauthorized editing of parameters.
Attention: This function is only valid to LCP, not active to local bus.

Par. No. Name Range Unit Default


C00.62 Time lock password 0~65535 0
Time lock password
C00.63 0~65535 0
value
TimePassword
C00.64 0~65535 0
confirmation value

6.2 Group 01: Load and Motor


C01.0* General Settings

Par. No. Name Range Unit Default


0: Speed open loop
Configuration
C01.00 3: Process closed loop 0
Mode
4: Torque open loop
0: Speed open loop, Enables speed control (without feedback signal
from motor) with automatic slip compensation for almost constant speed
at varying loads. Compensations are active but can be disabled in the
Load/Motor par. group C01.0*;
3: Process closed loop, Enables the use of process control in the
drive. The process control parameters are set in par. groups 7-2* and 7-3*.
4: Torque open loop, Enables the use of torque open loop in VVC+
mode (C01.01 Motor Control Principle). The torque PID parameters are
set in par. group C07.1*;
Attention: If configuration mode is changed, C03.00, C03.03 will be
restored to factory setting.

Par. No. Name Range Unit Default


Motor Control 0: V/F
*C01.01 1
Principle 1: VVC+

- 78 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Selects which motor control principle to employ.


0: V/F, for special motor or parallel connected motors in special
motor applications. When V/F is selected the characteristic of the control
principle can be edited in C01.55 V/F Characteristic - V and C01.56 V/F
Characteristic – F;
1: VVC+, Voltage Vector Control principle suitable for higher
requirements on control performance applications. The main benefit of
VVC+ operation is that it uses a robust motor model;
Attention: When V/F control principle is selected, slip compensation
and load compensation are invalid; When VVC+ control principle is
selected,it includes slip compensation and load compensation itself.

Par. No. Name Range Unit Default


0: Constant torque
Torque 1: Variable torque
*C01.03 1
Characteristics 3: Auto Energy
Optimization (AEO)

Select the torque characteristic required. VT and AEO are both


energy saving operations.
0: Constant torque, Motor shaft output provides constant torque
under variable speed control.
1: Variable torque, Motor shaft output provides variable torque
undervariable speed control, usually used for fan or pump applications.
Set the variable torque level in C14.40 VT Level.
3: Auto Energy optimization (AEO), Automatically optimises
energy consumption by minimising magnetisation and frequency
viaC14.41 AEO Minimum Magnetisation;

Par. No. Name Range Unit Default


Application
0: No function
*C01.07 Configuration 0
2:water control
Mode

This parameter enables a choice of a configuration setting that fits


different applications. Wobble function is only valid under speed open
loop. If wobble function is selected, parameterC03.00 will be set to “0”.
0: No function;
2: water control,see parameter group C25.*;

HLP-SP110 Series Operating Manual - 79 -


HLP-SP110 Series

C01.2* Motor Date

Par. No. Name Range Unit Default


*C01.20 Motor Power Motor dependant kW *
*C01.22 Motor Voltage 50~1000 V *
*C01.23 Motor Frequency 20~400 Hz *
*C01.24 Motor Current Motor dependant A *
*C01.25 Motor Speed 100~9999 rpm *
Set the parameters according to the motor nameplate no matter whether
V/F control or VVC+ control is adopted.
Cha ng i ng t he value of C01.20 - C01.22 , C01.30 - C01.35 w i l l be
automatically modified to factory settings.

Par. No. Name Range Unit Default


0: Disabled
1: Enable complete
Automatic Motor
*C01.29 AMA 0
Adaption (AMA)
2: Enable reduced
AMA

The AMA function optimises dynamic motor performance by


automatically optimising the advanced motor parameters (C01.30 Stator
Resistance (Rs) to C01.35 Main Reactance (Xh)) at motor standstill.
Activate the AMA function by pressing HAND key after selecting [1]
or [2]. See also the chapter 7.
0: Disabled;
1: Enable complete AMA, Performs AMA of the stator resistance
RS, therotor resistance Rr, the stator leakage reactance X1 and the main
reactance Xh. Do not select this option if an LC filter is used between the
drive and the motor;
2: Enable reduced AMA, Performs a reduced AMA of the stator
resistanceRs in the system only.

C01.3* Adv.Motor Data

Par. No. Name Range Unit Default


*C01.30 Stator Resistance (Rs) Motor dependant Ω *
Stator Leakage
*C01.33 Motor dependant Ω *
Reactance (X1)
*C01.35 Main Reactance (Xh) Motor dependant Ω *

- 80 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Parameters for advanced motor data. The motor data in C01.30 Stator
Resistance (Rs) to C01.35 Main Reactance (Xh) must match the relevant
motor in order to run the motor optimally. The default settings are figures
based on common motor parameter values from standard motors. If the
motorparameters are not set correctly, a malfunction of the drive system
may occur. If the motor data is not known, running an AMA (Automatic
Motor Adaptation) is recommended.

Par. No. Name Range Unit Default


*C01.39 Motor Poles 2~100 P 4

Enter the motor poles from the nameplate data.

C01.4* Motor Cable Length

Par. No. Name Range Unit Default


*C01.42 Motor Cable Length 0~150 m *

Enter the motor cable length connected between the motor and the drive.
Set correct cable length can suppress noises resulted from the motor.

C01.5* Load Indep.Setting

Par. No. Name Range Unit Default


Motor Magnetisation at Zero
C01.50 0~300 % 100
Speed
Min Speed Normal
C01.52 0.0~10.0 Hz 1.0
Magnetising

Use C01.50 Motor Magnetisation at Zero Speed along with C01.52 Min
SpeedNormal Magnetising to obtain a different thermal load on the
motor when running at low speed (under C01.52).
The value of C01.50 is a percentage of the motor current. If the setting is
too low, the torque on the motor shaft may be reduced.

Magn.current
C01.50
100%

C01.52 Hz

HLP-SP110 Series Operating Manual - 81 -


HLP-SP110 Series

Par. No. Name Range Unit Default


C01.55 V/F Characteristic-V 0.0~999.9 V *
C01.56 V/F Characteristic-F 0.0~400.0 Hz *

These parameters are array parameters [0-5], used to manually form a V/


F characteristic matching the motor. The frequency points [F0-F5] are
defined in C01.56 V/F Characteristic - F. The voltage at each point [V0-V5]
is defined in C01.55 V/F Characteristic - V. These parameters are only
accessible when C01.01 Motor Control Principle is set to V/F.
Voltage

Frequency
C01.55[0]~C01.55[5] is respective to V0~V5, C01.56[0]~C01.56[5] is
respective to F0~F5, Vn is motor rated voltage, Fn is the motor rated
frequency.
The set of C01.56 must met F0=0 and F1≤F2≤F3≤F4≤F5.
Simplify V/F characteristic by merging 2 or more points (voltages and
frequencies), which respectively are set equal.
The slope (ratio of V/F) after point (F5, V5) must be equal to the slope
between point (F5, V5) and the previous point.
Voltage

Frequency

- 82 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

The default settings of V/F Characteristic are:


200V model:
[0] [1] [2] [3] [4] [5]
C01.55 0.0 7.0 230.0 230.0 230.0 230.0
C01.56 0.0 0.5 50.0 50.0 50.0 50.0

400V model:

[0] [1] [2] [3] [4] [5]


C01.55 0.0 12.0 400.0 400.0 400.0 400.0

C01.6* Load Depen.Setting

Par. No. Name Range Unit Default


C01.60 Low Speed Load Compensation 0~199 % 100
C01.61 High Speed Load Compensation 0~199 % 100

Enter the % value to compensate voltage in relation to load when the


motor is running at low speed (C01.60)/high speed (C01.61) and obtain
the optimum V/F characteristic.
The low speed and high speed change-over point is automatically
calculated based on motor size.Usually it is 5Hz.

Voltage
100%

60%

0
Change-over Frequency

Par. No. Name Range Unit Default


C01.62 Slip Compensation -400~399 % 0

When the motor is driving an electric-driven load, motor speed dropswith


the increase of load. When the motor is driving a power generating load,
motor speed will increase with the increase of load. Appropriate slip
compensation can maintain constant motor speed when the motor load is
changing.

HLP-SP110 Series Operating Manual - 83 -


HLP-SP110 Series

If this parameter is set to 100%, it indicates that the compensation when


the motor bears rated load is the rated motor slip.
Diagram of slip compensation is shown below:
Motor speed
Slip compensation 100%
Slip compensation 50%
Slip compensation 0%

n1=rated motor speed+100%*rated slip


n2=rated motor speed+50%rated slip
n3=rated motor speed
Motor load
Rated load
slip compensation on electric driven load

Motor speed

Slip compensation 0%

Slip compensation 50%

Slip compensation 100%


n3=rated motor speed
n2=rated motor speed+50%rated slip
n1=rated motor speed+100%*rated slip

Motor load
Rated load
slip compensation on power generating load
When having more than one motor on the same shaft there is a need for
some kind of load share between the drives controlling the motors. This
has typically been made with two drives running in speed open loop
mode and one with negative slip compensation.

Par. No. Name Range Unit Default


Slip Compensation Time
C01.63 0.05~5.00 s 0.30
Constant

Enter the slip compensation reaction speed. A high value results in slow
reaction, and a low value results in quick reaction. If low-frequency
resonance problems arise, use a longer time setting.

- 84 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par. No. Name Range Unit Default


C01.64 Resonance Dampening 0~3000 % *

Motor (especially >=30kW motor) speed and current resonance is likely


to occur due to load vibration, and may lead to system failure even over
current protection. This is particularly obvious during no-load or light-
load applications.
Do not change this parameter if the motor has no resonance. Increase the
value properly only when the motor has obvious resonance. The larger
the value is, the better the resonance dampening result will be.

Par. No. Name Range Unit Default


Resonance Dampening
C01.65 0.005~0.050 s 0.005
Time constant
Enter the resonance dampening reaction speed. A high value results in
slow reaction, and a low value results in quick reaction.

C01.7* Start Adjustments

Par. No. Name Range Unit Default


C01.71 Start Delay 0.0~10.0 s 0.0

This parameter enables a delay of the starting time. The drive begins
with the start function selected in C01.72. Enter the time delay required
before commencing acceleration. Setting start delay to 0.0 sec. disables
start function when start command is given.

Par. No. Name Range Unit Default


0: DC Hold
C01.72 Start Function 2
2: Coast

Select the start function during start delay. This parameter is linked to
C01.71 Start Delay.
0: DC Hold, Energizes motor with a DC holding current (C02.00 DC
Hold Current) during the start delay time;
2: Coast, Motor coasted during the start delay time (drive off);

Par. No. Name Range Unit Default


0: Disabled
*C01.73 Flying Start 0
1: Enabled

HLP-SP110 Series Operating Manual - 85 -


HLP-SP110 Series

This function applies for the inertia load to restart due to mains drop-out;
If [0] Clockwiseis selected in C04.10, and no rotating motor is found, It
is possible to use DC-brake command to ramp down the motor speed to 0
rpm, and then start the motor in the normal way; If [2]Both directions is
selected in C04.10, and no rotating motor is found, the drive will assume
the motor is stationary or in low-speed rotation, and then start the motor
in the normal way. When Flying start is enabled, C01.71 Start delay and
C01.72 Start function is disabled.
Warning: This function is not suitable for hoisting applications.
Par. No. Name Range Unit Default
C01.75 Min. Start Frequency 0.00~10.00 Hz 0.00
If the drive frequency reference is less than C01.75 Min. Start Frequency,
the drive will not run even the start command is given (the start command
will be shielded). Only the drive frequency reference is greater than or
equal C01.75, then the drive starts to run. The drive still accelerates from
0 to frequency reference using ramp time.

Par. No. Name Range Unit Default


C01.76 Jump Frequency 0.0~20.0 Hz 0.0

If the drive frequency reference’s absolute value (not zero, frequency


reference maybe negative)is less than C01.76Jump Frequency, the drive
will run at jump frequency (maybe reversing if the reference is negative).
For example:
Set C01.76 = 3. if the frequency reference is 2, the drive will run forward
at 3Hz; If the frequency reference is -2, the drive will run reversing at
3Hz; If the frequency reference is 0, the drive will stop. If the frequency
reference is 20, the drive will run at 3Hz immediately, thenaccelerates
from 3Hz to 20Hz using ramp time.
Note: it is not recommended for using C01.75 and C01.76 together.
If C01.75 and C01.76 are used together, the following talbe is its
behaviour.

- 86 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Freq. ref.
3Hz 8Hz 15Hz
Par. setting
Freq. ref > Freq. ref > C01.75,
C01.75, the start command
Freq. ref <
the start is given,
C01.75
command is Freq. ref > C01.76
C01.75 = 5.00 the start
given, the drive runs at
C01.76 = 10.0 command is
Freq. ref < 10Hz immediately,
shielded, the
C01.76 then accelerates
drive stop.
the drive runs from 10Hz to 15Hz
at 10.0Hz using ramp time.
Freq. ref > C01.75,
the start command
Freq. ref < Freq. ref <
is given,
C01.75 C01.75
Freq. ref > C01.76
C01.75 = 10.00 the start the start
the drive runs at
C01.76 = 5.0 command is command is
5Hz immediately,
shielded, the shielded, the
then accelerates
drive stop. drive stop.
from 5Hz to 15Hz
using ramp time.

Attention: When C01.76 Jump Frequency and C02.04 DC Brake Cut


in Speed are not zero, DC brake will only be active when
C02.04 > C01.76.

HLP-SP110 Series Operating Manual - 87 -


HLP-SP110 Series

C01.8* Stop Adjustments

Par. No. Name Range Unit Default


0: Coast
C01.80 Function at Stop 0
1: DC Hold

Select the drive function after stop command is given or start command
is removed (standby), and output frequency is ramped down to C01.82
Min Speed for Function at Stop.
0: Coast, Leaves motor in free mode. the drive is off;
1: DC Hold, the motor is energized with a DC current. See C02.00
DC Hold Current for more information;
Diagram of Function at Stop is shown below:

Output
输出频率 Output
输出频率
Frequency Frequency

C01.82 C01.82

Time
时间 Time
时间
Output
输出电压 Output
输出电压
Voltage Voltage

0V C02.00

Time
时间 Time
时间
Start
运行信号 OFF Start
运行信号
ON ON OFF
Command Command
或 ON 或 ON
or Stop OFF or Stop
OFF
Command
停止信号 Command
停止信号
Coast
惯性停车 DC Hold
直流夹持
Par. No. Name Range Unit Default
Min Speed for
C01.82 0.0~400.0 Hz 0.0
Function at Stop

Set the output frequency at which to activate C01.80 Function at Stop.

- 88 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C01.9* Motor Temperature


Par. No. Name Range Unit Default
0: No protection
1: Thermistor warning
Motor Thermal
C01.90 2: Thermistor trip 0
Protection
3: ETR warning
4: ETR trip

The drive determines the motor temperature for motor protection in two
different ways:
• Via a thermistor sensor connected to the analog input terminal VI
(C01.93 Thermistor Source).
•Via calculation (ETR = Electronic Terminal Relay) of the thermal
load,
based on the actual load and time. The calculated thermal load
is compared with the rated motor current IM,N and the rated motor
frequency fM,N. The calculations estimate the need for a lower load at
lower speed due to less cooling from the fan incorporated in the motor.
0: No protection;
1: Thermistor warning, a thermistor connected to analog input VI
gives a warning if upper limit of motor temperature range is exceeded, (see
01.93, Thermistor Resource);
2: Thermistor trip, a thermistor connected to analog input VI gives
an alarm and makes the drive trip if upper limit of motor temperature
range is exceeded, (see 01.93, Thermistor Resource);
3: ETR warning,if calculated upper limit of motor temperature
range is exceeded, a warning occurs
4: ETR trip,if calculated upper limit of motor temperature range is
exceeded, an alarm occurs and the drive trips.

Par. No. Name Range Unit Default


Thermistor 0: None
*C01.93 0
Resource 1: Terminal VI
Select the input to which the ther mistor (PTC sensor) should be
connected.
0: None
1: Terminal VI, Connect thermistor to analog input terminal VI;
Attention: Analog input can’t be selected for other purpose when selected
as thermistor resource.
Thermistor specifications:
Input Signal Type Voltage Supply Termistor Threshold
Analog 10V <0.8kΩ, >2.9kΩ

HLP-SP110 Series Operating Manual - 89 -


HLP-SP110 Series

6.3 Group 02: Brakes


C02.0* DC-Brake

Par. No. Name Range Unit Default


C02.00 DC Hold Current 0~150 % 50
Enter a value for holding current as a percentage of the rated motor
cu r rent set in C01.24 Motor Cu r rent. 100% DC holding cu r rent
corresponds to IM,N. This parameter either holds the motor (holding
torque) or pre-heats the motor. This parameter is active if DC Hold has
been selected in either C01.72 Start Function or C01.80 Function at Stop.
Attention: Avoid 100% current too long as it may overheat the motor.

Par. No. Name Range Unit Default


C02.01 DC Brake Current 0~150 % 50
Enter a value for current as a percentage of the rated motor current IM,N,
see C01.24 Motor Current. 100% DC braking current corresponds to
IM,N.
DC brake current is applied on a stop command, when the speed is lower
than the limit set in C02.04 DC Brake Cut In Speed; or via the serial
communication port. The braking current is active during the time period
set in C02.02 DC Braking Time.
Par. No. Name Range Unit Default
C02.02 DC Braking Time 0.0~60.0 s 10.0
This parameter defines DC brake current (C02.01) time during which
DC-brake current is applied to the motor.

Par. No. Name Range Unit Default


C02.04 DC Brake Cut in Speed 0.0~400.0 % 0.0
Set the DC brake cut-in speed for activation of the DC braking current set
in C02.01 DC Brake Current, upon a stop command.

Par. No. Name Range Unit Default


C02.08 Motor Demagnetization 0~100 % 100
when the drive output frequency less than DC brake cut in frequencies,
motor demagnetization process needs to be done before starting a
DC brake for preventing overcurrent at a high speed or great inertia
starting DC brake. The smaller this parameter is, the faster motor
demagnetization will be done, the time shorter entering the DC brake.
If the Load inertia is small and DC brake cut in frequency is lower, this

- 90 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

parameter can be reduced to 0.


Diagram of DC Brake process is shown below:

Output
输出频率Hz
Frequency

DC直流制动
Brake
Cut切入频率
in Speed
Time
时间t
Demagnetization
电机消磁时间 Time
Output
输出电压V
DC Braking Time
直流制动时间
Voltage

DC Brake
直流制动量

Time
时间t
ON
Start
运行命令
Command OFF

C02.1* Brake Energy Funct.

Par. No. Name Range Unit Default


0: Off
C02.10 Brake Function 0
2: AC brake
0: Off;
2: AC brake, dissipate surplus energy in the motor core, and prevent
the energy back into drive causing trips. It is important to keep in
mind that frequent use of this function will cause an increase in motor
temperature;
Attention: Resistor brake is only functional when the drive build-in
braking unit or external braking unit must be installed.

Par. No. Name Range Unit Default


C02.16 AC Brake, Max Current 0~150 % 100

Enter the maximum permissible current when using AC brake to avoid


overheating of motor windings. 100% equals motor current set in C01.24.

Par. No. Name Range Unit Default


0: Disabled
C02.17 Over-voltage Control 2: Mode 1 3
3: Mode 2

HLP-SP110 Series Operating Manual - 91 -


HLP-SP110 Series

Over-voltage control (OVC) reduces the risk of the drive tripping due to
an over voltage on the DC link caused by generative power from the load.
0: Disabled;
2: Mode 1, used to consume surplus energy by increasing the output
frequency;
3: Mode 2, used for very short deceleration;
Attention: If C02.10 = 1 (Resistor brake), C02.17 = 2 or 3, resistor brake
function starts first, if the DC link voltage still can not be
controlled, OVC starts.

Par. No. Name Range Unit Default


Over-voltage Control
C02.18 0.01~0.10 s 0.05
Integral Time

Par. No. Name Range Unit Default


Over-voltage Control
C02.19 0~200 % 100
Proportional Gain

Over-voltage control (OVC) reduces the risk of the drive tripping due to
an over voltage on the DC link caused by generative power from the load.
Note: These parameters are only active when selecting [2] Mode 1or [3]
Mode 2 in C02.17 Over-voltage Control

C02.2* Mechanical Brake


Parameters for controlling operation of an electro-magnetic (mechanical)
brake, typically required in hoisting applications.
To control a mechanical brake, a relay output (FA-FB-FC or KA-KB) or
a programmed digital output (DO1 or DO2) is required. Normally this
output must be closed during periods when the drive is unable to ‘hold’
the motor, e.g. due to an excessive load. Select [32] Mechanical Brake
Control for applications with an electro-magnetic brake in C05.40 Relay
output, C05.30 DO1 Output, or C05.31 DO2 Output. When selecting
[32] Mechanical brake control, the mechanical brake is closed from start
up until the output current is above the level selected in C02.20 Release
Brake Current. During stop, the mechanical brake activates when the
speed falls below the level specified in C02.22 Activate Brake Speed.
If the drive enters an alarm condition or an over-current or over-voltage
situation, the mechanical brake immediately cuts in. This is also the case
during safe stop.

Par. No. Name Range Unit Default


Release Brake
C02.20 0.00~1200.00 A 0.00
Current

- 92 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Set the motor current for release of the mechanical brake, when a start
condition is present.
Attention: When Mechanical brake control output is selected but no
mechanical brake is connected, the function will not work.
If start delay time has passed, and motor current is below
Release brake current, drive trips.

Par. No. Name Range Unit Default


C02.22 Activate Brake Speed 0.0~400.0 Hz 0.0
Set the motor frequency for activation of the mechanical brake, when a
stop condition is present.
Diagram of Mechanical Brake Control process is shown below:

Output
输出频率Hz
Frequency

Activate
机械制动
Brake频率
Speed

Time
时间t
Output
输出电流A
Current

Release
机械制动
Brake
电流
Current
Time
时间t
Mechanical
抱闸控制
Brake
Control ON ON

OFF
Time
时间t
Start
运行命令 ON
command OFF

HLP-SP110 Series Operating Manual - 93 -


HLP-SP110 Series

6.4 Group 03: Reference/Ramps


C03.0* Reference Limits
ence is the drive control target. Reference value is a dimensionless
number, reference unit depends on configuration mode (C01.00). When
select [0] speed open loop in configuration mode, motor frequency is
the drive control target, the reference unit is Hz; When select [4] torque
open loop in configuration mode, motor torque is the drive control
target, the reference unit is Nm; When select [3] process closed loop in
configuration mode, process variable (such as temperature, pressure) is
the drive control target, the reference unit may be °C or kg, etc.

Par. No. Name Range Unit Default


0: 0~Max
C03.00 Reference Range 0
1: -Max~+Max

Select the range of the reference.


0: 0~Max, Reference set point ranges can have positive values only;
1: -Max~+Max, Ranges can have both positive and negative values;

Par. No. Name Range Unit Default


C03.03 Maximum Reference C03.02~4999.000 50.000

Enter value for Maximum Reference. The Maximum Reference is the


highest value obtainable by summing all references.

Par. No. Name Range Unit Default


Main 0: Preset reference +
C03.07 Reference Reference source1, 2, 3 0
Calculation 1: Preset reference priority

Select main reference calculation method.


0: Preset reference + reference source1, 2, 3
1: Preset reference priority
For option [1],
Preset reference[1-N] when use preset reference
1-N
Main reference =
Preset reference [0] + Reference source 1, 2, 3
when use preset reference 0

- 94 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C03.1* References
Diagram of Reference Calculation is shown below:

Par. No. Name Range Unit Default


C03.10 Preset Reference -100.00~100.00 % 0.00

This parameter is an ar ray-16 to be used for presetting different


references. 16 preset references are selectable via digital terminals or
local bus. See C05.1*. 0% equals 0, 100% equals value set in C03.03.

HLP-SP110 Series Operating Manual - 95 -


HLP-SP110 Series

Par. No. Name Range Unit Default


C03.11 Jog Speed 0.0~400.0 Hz 0.0

The jog speed is a fixed output speed at which the drive is running when
the jog function is activated.
The drive with the highest priority will operate at jog speed when a
variety of run command activates. Removing the jog signal makes the
drive run according to the selected configuration, this parameter is set
limited by C04.14.
Par. No. Name Range Unit Default
C03.12 Catch up/Slow down Value 0.00~100.00 % 0.00

This parameter enables the entry of a percentage value (relative) which


will to be either added to or deducted from the total reference.
The Catch up/Slow down function is activated by a digital input terminal
(See C05.1*,choose [28]/[29]). If this function is active, the catch up/slow
down value will be added to the total reference constituting new setting
at which the drive is going to run, calculated as follows:
Reference= total reference ± total reference × (Catch up/Slowdown value)
If this function is inactive, the reference returns to its original value.

Par. No. Name Range Unit Default


C03.13 Speed Up/Down Value 0.01~50.00 Hz 0.10

Enter the Speed Up/Down value.


Par. No. Name Range Unit Default
C03.14 Preset Relative Reference -100.00~100.00 % 0.00

Define an adjustable Preset Relative Reference which is to be added


to the total reference as a percentage value of the actual reference. Its
calculation refers to Reference Calculation Diagram.
Par. No. Name Range Unit Default
C03.15 Reference Source 1 0: No function 1
C03.16 Reference Source 2 1: Terminal VI 0
2: Terminal AI
C03.17 Reference Source 3 11: Local bus 11
21: LCP potentiometer

Select the reference input to be used for the first, second and third
reference source.
0: No function;
1: Terminal VI, useanalog input VI as reference source, see C06.1*;

- 96 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

2: Terminal AI, useanalog input AI as reference source, see C06.2*;


11: Local bus, use local bus reference as reference source, see
C08.**;
21: LCP potentiometer, use LCP potentiometer as reference source,
see C06.8*;

Par. No. Name Range Unit Default


0: No function
Speed Up/Down
C03.19 1: Stop save 0
Value Store
2: Power down save

This parameter is used for setting whether to save the data changed in the
Speed Up/Down function if the drive stops or after it power down.

C03.4* Ramp1
There are 4 ramps built in the drive. For each of four ramps (C03.4*,
C03.5*, C03.6* and C03.7*), configure the ramp parameters: ramp type,
ramp up time and ramp down time.

Par. No. Name Range Unit Default


0: Linear
C03.40 Ramp 1 Type 0
2: S ramp
C03.41 Ramp 1 Ramp Up Time 0.05~3600.00 s *
Ramp 1 Ramp Down
C03.42 0.05~3600.00 s *
Time
0: Linear
C03.50 Ramp 2 Type 0
2: S ramp
C03.51 Ramp 2 Ramp Up Time 0.05~3600.00 s *
Ramp 2 Ramp Down
C03.52 0.05~3600.00 s *
Time
0: Linear
C03.60 Ramp 3 Type 0
2: S ramp
C03.61 Ramp 3 Ramp Up Time 0.05~3600.00 s *
Ramp 3 Ramp Down
C03.62 0.05~3600.00 s *
Time
0: Linear
C03.70 Ramp 4 Type 0
2: S ramp
C03.71 Ramp 4 Ramp Up Time 0.05~3600.00 s *
Ramp 4 Ramp Down
C03.72 0.05~3600.00 s *
Time

HLP-SP110 Series Operating Manual - 97 -


HLP-SP110 Series

Ramp Type:
0: Linear, motor ramps up/down with constant acceleration /
deceleration;
2: S ramp, motor rampsup/down with non-linear acceleration/
deceleration;
Ramp UpTime is the time motor accelerates from 0Hz to rated motor
frequency (C01.25).
Ramp Down Time is the time motor decelerates from rated motor
frequency (C01.25) to 0Hz.
Diagram of Ramp Type, Ramp Up Time and Ramp Down Time are
shown below:

Output Frequency

Rated
Motor S ramp
Linear
Speed Deceleration
Acceleration
Linear
S ramp
Deceleration
Acceleration
Ramp Up Time Ramp Down Time
Time

C03.8* Other Ramps

Par. No. Name Range Unit Default


C03.80 Jog Ramp Time 0.05~3600.00 s *

Enter the jog ramp time, i.e. the acceleration/deceleration time between
0Hz and the rated motor frequency (C01.25).
Jog ramp time starts upon activation of a jog signal via a selected digital
input or serial communication port.

- 98 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

6.5 Group 04: Limits/Warnings


C04.1* Motor Limits

Par. No. Name Range Unit Default


0: Clockwise
Motor Speed
*C04.10 1: Counter clockwise 2
Direction
2: Both directions

elect the motor speed direction(s) required. Use this parameter to


prevent unwanted reversing.
0: Clockwise, the motor shaft rotates in clockwise direction, this
setting prevents the motor from running in counter clockwise direction;
1: Counter clockwise, motor shaft rotates in counter clockwise
direction, this setting prevents the motor from running in clockwise
direction;
2: Both directions, with this setting, the motor can run in both
directions;

Par. No. Name Range Unit Default


*C04.12 Motor Speed Low Limit 0.0~C04.14 Hz 0.0

Set the minimum limit for Motor Speed, the motor speed low limit can
be set to correspond to the minimum output frequency of the motor shaft.
The Motor Speed Low
Limit must not exceed the setting in C04.14 Motor Speed High Limit

Par. No. Name Range Unit Default


*C04.14 Motor Speed C04.12~C04.19 Hz 50.0

Set the maximum limit for Motor Speed, the motor speed high limit can
be set to correspond to the maximum manufacture’s rated motor speed.
The motor speed high limit must exceed the Motor Speed Low Limit in
C04.12.

Par. No. Name Range Unit Default


C04.18 Current Limit 0~300 % 140

This parameter is used to set drive output current limit, 100% equals
motor current set in C01.24. If the output current exceeds the C04.18
motor current limit, the drive will report A.59 warning and current limit
controllers (see C14.3*) start.

HLP-SP110 Series Operating Manual - 99 -


HLP-SP110 Series

Par. No. Name Range Unit Default


*C04.19 Max Output Frequency 0.0~400.0 Hz 55

Provides a final limit on the output frequency for improved safety in


applications where you want to avoid accidental over-speeding. This
limit is final in all configurations (independent of the setting in C01.00
Configuration Mode).

Par. No. Name Range Unit Default


0: No function
Frequency Upper 1: Terminal VI
*C04.21 0
Limit Source 2: Terminal AI
11: Local bus

In some occasions, it needs to set a dynamic frequency upper


limit.For example, to avoid runaway in torque control mode in winding
application, you can set the frequency upper limit by means of analog
input. When the drive reaches the upper limit, it will continue to run at
this speed.
0: No function, use C04.19 as frequency upper limit;
1: Terminal VI, use analog input VI as frequency upper limit, see
C06.1*;
2: Terminal AI, use analog input AI as frequency upper limit, see
C06.2*;
11: Local bus, use local bus reference as frequency upper limit, see
C08.**;
21: LCP potentiometer, use LCP potentiometer as frequency upper
limit, see C06.8*;

Par. No. Name Range Unit Default


0: Disable
1: Counter A save
Counter Store at
C04.42 2: Counter B save 0
Power down
3: Both counter A and B
save
This parameter is used to control whether counter A/B’s value is saved at
power down.

- 100 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C04.5* Adjustable Warnings


This parameter group is used to adjust warning limits for current, speed,
reference and feedback. Warnings can be programmed as an output or
sent via serial bus.

Par. No. Name Range Unit Default


C04.50 Warning Current Low 0.00~Imax A 0.00
C04.51 Warning Current High 0.00~Imax A *

Enter the I low / I high value. When the motor current falls below I low or
exceeds I high, a signal can be produced on relays or terminal DO1/DO2.
See [12] Out of current range, [13] Below current low and [14] Above
current high in C05.30/31/40.
Diagram of Warning Current Low and Warning Current High are shown
below:
Output
Current
C04.51 Warning Current High

C04.50 Warning Current Low

Terminal DO1/DO2/Relays Time


ON ON ON
[12]Out of current range
OFF OFF

Terminal DO1/DO2/Relay
ON
[13]Below current low
OFF

ON
Terminal DO1/DO2/Relays
OFF OFF
[14]Above current high

Par. No. Name Range Unit Default


C04.52 Warning Frequency Low 0.0~400.0 Hz 0.0
C04.53 Warning Frequency High 0.1~400.0 Hz 65.0
Enter the f low / f high value. When the motor frequency falls below f low or
exceeds f high, a signal can be produced on relays or terminal DO1/DO2.
See [15] Out of frequency range, [16] Below frequency low and [17]
Above frequency high in C05.30/31/40.
Diagram of Warning Frequency Low and Warning Frequency High are
shown below:

HLP-SP110 Series Operating Manual - 101 -


HLP-SP110 Series

Output Frequency

C04.53 Warning Frequency High

C04.52 Warning Frequency Low

Terminal DO1/DO2/Relays ON Time


ON ON
[15]Out of frequency range
OFF OFF

Terminal DO1/DO2/Relays
ON
[16]Below of frequency low
OFF

ON
Terminal DO1/DO2/Relays
OFF OFF
[17]Above frequency high

Par. No. Name Range Unit Default


C04.54 Warning Reference Low -4999.000~4999.000 0.000
C04.55 Warning Reference High -4999.000~4999.000 50.000

Enter the low/high reference warning value. When the actual reference
falls below C04.54 or exceeds C04.55, a signal can be produced on
relays or terminal DO1/DO2. See [40] Out of reference range, [41] Below
reference low and [42] Above reference high in C05.30/31/40.

Par. No. Name Range Unit Default


C04.56 Warning Feedback Low -4999.000~4999.000 0.000
C04.57 Warning Feedback High -4999.000~4999.000 50.000

Enter the low/high feedback warning value. When the feedback falls
below C04.56 or exceeds C04.57, a signal can be produced on relays or
terminal DO1/DO2. See [18] Out of feedback range, [19] Below feedback
low and [20] Above feedback high in C05.30/31/40.

Par. No. Name Range Unit Default


0: Disable
*C04.58 Missing Motor Phase Function 1
1: Enable
Displays an alarm in the event of a missing motor phase (alarm 30, 31
or 32). Select disabled for no missing motor phase alarm. It is strongly
recommended to make an active setting to avoid motor damage.

- 102 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par. No. Name Range Unit Default


Current Limit 0: Warning off
*C04.59 1
warning function 1: Warning on
The function is valid for warning (A.59) . When C04.59 = 0, The
warning(A.59) will not be displayed.

C04.6* Speed Bypass

Par. No. Name Range Unit Default


C04.61 Bypass Speed From 0.0~400.0 Hz 0.0
C04.63 Bypass Speed to 0.0~400.0 Hz 0.0

Some systems call for avoiding certain output frequencies, due to


resonance problems in the system. A maximum of three frequency ranges
can be avoided. The drive will pass quickly when it approaching to the
Bypass Speed area.
These parameters are dyadic array, [0] is used to set the bypass speed
range 1, [1] is used to set the bypass speed range 2, and [2] is used to set
the bypass speed range 3.
Diagram of bypass speed ranges are shown below:
Output
Frequency
C04.63[2]
C04.61[2] Bypass Frequency
Range3
C04.63[1]
C04.61[2] Bypass Frequency
Range2
C04.63[0]
C04.61[2] Bypass Frequency
Range1

Time

HLP-SP110 Series Operating Manual - 103 -


HLP-SP110 Series

6.6 Group 05: Digital In/Out


C05.1* Digital Input

Par. No. Name Range Unit Default


C05.04 DI Filter Time 2~16 ms 4
It is used to set the software filter time of DI terminal status. If DI
terminals are liable to interference and may cause malfunction, increase
the value of this parameter to enhance the anti-interference capability.
However, increase of DI filter time will reduce the response of DI
terminals.
Par. No. Name Range Unit Default
C05.05 DI Logical function 0~255 0
C05.06 DO/RL Logical function 0~255 0
0: Inivalid
1: Freeze output frequency
DI external fault 2: Stop
C05.09 0
function 3: Jog Frequency
4: Max Frequency
5: Stop and fault
C5.05 and C5.06 these two parameters define signal for input/output
terminal;
C5.05 Bit4 Bit3 Bit2 Bit1 Bit0
terminal DI3 DI2 DI1 REV FOR
bit:0:express positive logic; 1:express negative logic;
C5.06 Bit4 Bit3 Bit2 Bit1 Bit0
terminal KA4-KB4 KA3-KB3 KA2-KB2 KA1-KB1 FA-FB-FC
bit:0:express positive logic; 1:express negative logic;
Par. No. Name Range Unit Default
C05.10 Terminal FOR 8
C05.11 Terminal REV 0
C05.12 Terminal DI1 0~111 0
C05.13 Terminal DI2 0
C05.14 Terminal DI3 0
The digital inputs are used for selecting various functions inthe
drive. All digital inputs can be set to thefollowing functions:
0: No operation, no reaction to signals transmitted to the terminal;
1: Reset, reset the drive after a Trip/Alarm;
2: Coast inverse, no output, leaving the motor coasting to stop.
Terminal logic ‘0’ => coasting stop;
3: Coast and reset inverse, the drive resets leaving the motor

- 104 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

coasting to stop. Terminal logic ‘0’ => coasting stop;


6: Stop inverse, the drive is stopped according to selected ramp time.
Terminal logic ‘0’ => stop;
8: Start, select start for a start/stop command. Terminal logic ‘1’ =
start, logic ‘0’ = stop;
9: Latched start, The motor starts, if a pulse is applied for min. 4ms.
The motor stops when [6]Stop inverse/[46]Stop is activated;
10: Reversing, change direction of motor shaft rotation, reversing
signal only changes direction of rotation, it does not activate start
function, C04.10 must choose [2] Both directions;
11: Start reversing, used for start/stop and for reversing at the same
time;
12: Enable start forward only, disengages the counterclockwise
movement and allows for the clockwise direction;
13: Enable start reverse only, disengages the clockwise movement
and allows for the counterclockwise direction;
14: Jog, used for activating jog speed, see C03.11;
15: Preset ref. bit0, Preset ref.bit0, bit1, bit2, bit3 enables a
choicebetween one of the sixteenpreset references (see C03.10) according
to the table below;
16: Preset ref. bit1, same as [15];
17: Preset ref. bit2, same as [15];
18: Preset ref. bit3, same as [15];
Terminal of Terminal of
Terminal of Preset ref.
Preset ref. Preset ref. Parameter
Preset ref. bit1 bit0
bit3 bit2
OFF OFF OFF OFF C03.10[0]
OFF OFF OFF ON C03.10[1]
OFF OFF ON OFF C03.10[2]
OFF OFF ON ON C03.10[3]
OFF ON OFF OFF C03.10[4]
OFF ON OFF ON C03.10[5]
OFF ON ON OFF C03.10[6]
OFF ON ON ON C03.10[7]
ON OFF OFF OFF C03.10[8]
ON OFF OFF ON C03.10[9]
ON OFF ON OFF C03.10[10]
ON OFF ON ON C03.10[11]
ON ON OFF OFF C03.10[12]
ON ON OFF ON C03.10[13]
ON ON ON OFF C03.10[14]
19: Freeze reference, freezes the actual reference,If freezing
reference is active, stop the drive via a terminal programmed for [2]

HLP-SP110 Series Operating Manual - 105 -


HLP-SP110 Series

Coast inverse, [3] Coast and reset inverse, [42] Coast and [46] Stop;
20: Freeze output, freezes the output frequency, If freezing output is
active, stop the drive via a terminal programmed for [2] Coast inverse, [3]
Coast and reset inverse, [42] Coast and [46] Stop;
21: Speed up, when Speed up is activated for less than 400 ms. the
resulting reference will be increased by C03.13 Speed Up/Down Value. If
Speed up is activated for more than 400 ms, the resulting reference will
ramp according to ramp 4;
22: Speed down, similar to [21] Speed up;
23: Set-up select, select one of the two set-ups, see C00.10;
28: Catch up, select catch up to increase the resulting reference value
by the percentage set in C03.12Catch up/slow Down Value;
29: Slow down, similar to [28]Catch up;
32: Pulse input, select pulse input when using a pulse sequence as
either reference or feedback. Scaling is done in par. group C05.5*, the
function is available for C05.15 Terminal DI4 only;
34: Ramp bit0, ramp bit0, bit1 are used for select one of the four
ramps;
35: Ramp bit1, same as [34];

Terminal of Preset ref. bit1 Preset ref. bit0 Parameter


OFF OFF Ramp1 (C03.41, C03.42)
OFF ON Ramp2 (C03.51, C03.52)
ON OFF Ramp3 (C03.61, C03.62)
ON ON Ramp4 (C03.71, C03.72)
42: Coast, similar to [2] coast reverse, but logic contrary: Terminal
logic ‘1’ => coasting stop;
46: Stop, similar to[6] stop reverse, but logic contrary: Terminal
logic ‘1’ => stop;
60: Counter A, to count the pulse number inputted into the terminal;
62: Reset counter A, to clear counter A to “0”;
63: Counter B, to count the pulse number inputted into the terminal;
65: Reset counter B, to clear counter B to “0”;
110: invalid closed-loop
160: multi pump control, pump 1 enable terminal
161: multi pump control: pump 2 enable terminal
162: multi pump control: pump 3 enable terminal
163: multi pump control: pump 4enable terminal
164: multi pump control: pump 5enable terminal
165: multi pump control: pump 6 enable terminal
171: water supply function: the speed of the open loop speed running
signal, taking the VI channel setting value as the target frequency value.

- 106 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C05.4* Relay

Par. No. Name Range Unit Default


C05.40 Relay Function 0~192 5, 9

This parameter is an array[2] parameter. C05.40[0] corresponds to


the relay 1 (FA-FB-FC), C05.40[2] the corresponds to relay 2 (KA-KB).
0: No operation;
1: Drive ready
2: Drive ready, the drive control card have received supply voltage;
3: Remote control ready, the drive is ready for operation and is in
AUTO mode;
4: Drive running/No warning, the drive is running and no warning
is present;
5: Drive running, the drive is running;
7: Run in range/ No war ning, the drive is r unning within the
programmed speed ranges set in C04.12 Motor Speed Low Limitand
C04.14 Motor Speed High Limit. No warnings are present;
8: Run on reference/No warning, the drive runs at reference speed
without warnings;
9: Alarm, the drive alarms;
10: Alarm or warning, an alarm or warning occurs;
12: Out of current range, output current is outside the range set in
C04.50 and C04.51;
13: Below current low, output current is lower than set in C04.50;
14: Above current high, output current is higher than set in C04.51;
15: Out of frequency range, output frequency is outside the range set
in C04.52 and C04.53;
16: Below frequency low, output frequency is lower than set in
C04.52;
17: Above frequency high, output frequency is higher than set in
C04.53;
18: Out of feedback range, feedback is outside the range set in
C04.56 and C04.57;
19: Below feedback low, feedback is lower than set in C04.56;
20: Above feedback high, feedback is higher than set in C04.57;
21: Thermal warning, a thermal warning occurs;
22: Ready, no Thermal warning, the drive is ready for operation and
no over-temperature warning is present;
23: Remote ready, no Thermal Warning, the drive is ready for
operation in AUTO mode, and no over-temperature warning is present;
24: Ready, voltage OK, the drive is ready for operation, no over-
voltage or under-voltage is present;
25: Reverse, the drive runs in counter clockwise;
26: Bus OK, local bus communication is normal;

HLP-SP110 Series Operating Manual - 107 -


HLP-SP110 Series

32: Mech. brake control, enter mechanical brake control signal, see
C02.2*;
36: Control word bit11, bit11 in control word is active;
37: Control word bit12, bit12 in control word is active;
40: Out of reference range, reference is outside the range set in
C04.54 and C04.55;
41: Below reference low, reference is lower than set in C04.54;
42: Above reference high, reference is higher than set in C04.55;
51: Drive in HANDstate;
52: Drive in AUTOstate;
56: Drive in HANDstate;
57: Drive in AUTOstate;
60: Comparator 0, using a simple PLC, the results of comparator 0;
61: Comparator 1, using a simple PLC, the results of comparator 1;
62: Comparator 2, using a simple PLC, the results of comparator 2;
63: Comparator 3, using a simple PLC, the results of comparator 3;
70: Logic rule 0, using a simple PLC, the results of logic rule 0;
71: Logic rule 1, using a simple PLC, the results of logic rule 1;
72: Logic rule 2, using a simple PLC, the results of logic rule 2;
73: Logic rule 3, using a simple PLC, the results of logic rule 3;
80: Simple PLC digital rutput 1, only active for DO1;
81: Simple PLC digital output 2, only active for DO2;
82: Simple PLC relay 1, only active for relay 1;
83: Simple PLC relay 2, only active for relay 2;
84: Simple PLC relay 2, only active for relay 3;
160: Water supply: low voltage alarm control
161: Water supply: Over voltage alarm control
162: Water supply: Sleep
163: Water supply:Belt breaking signal
164: Water supply:No inverter available
192: Water supply:Relay control
Par. No. Name Range Unit Default
FA/FB/FC;
KA1/KB1;
KA2/KB2;
C05.41[x] Closed relay delay s 0.00
KA3/KB3;
KA4/KB4;
KA5/KB5
Par. No. Name Range Unit Default
FA/FB/FC;
KA1/KB1;
KA2/KB2;
C05.42[x] Open relay delay s 0.00
KA3/KB3;
KA4/KB4;
KA5/KB5

- 108 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

6.7 Group 06: Analog In/Out


C06.0* Analog I/O Mode

Par. No. Name Range Unit Default


C06.00 Live Zero 1~99 s 10

Live Zero Time-out Function is used for analog input signal detection.
To active the Live Zero Timeout Function, if voltage input is selected,
then the low input voltage (C06.10, C06.20) settings must be greater than
1V; if current input is selected, the low input current (C06.12, C06.22)
settings must be greater than 2mA or more. If the analog input signal is
lower than 50% of the settings of parameters of C06.10, C06.12, C06.20,
C06.22, and lasts longer than the settings of C06.00Live Zero Timeout
Time, this feature takes effect.
If the analog input signal is back to normal within the delay time,
thenreset the timer.
Diagram of Live Zero Timeout Function is shown below:
Analog Input

50%
C06.10,C06.12,
C06.20,C06.22, Live Zero Timeout

C06.00 Time
Live Zero Timeout
Time

Par. No. Name Range Unit Default


0: Off
1: Freeze output
2: Stop
C06.01 Live Zero Timeout Function 0
3: Jogging
4: Max. speed
5: Stop and trip

Select the live zero time-out function.


0: Off;
1: Freeze output, frozen at the present value;
2: Stop, overruled to stop;
3: Jogging, overruled to jog speed;
4: Max. speed, overruled to Max.speed;
5: Stop and trip, overruled to stop with subsequent trip.
HLP-SP110 Series Operating Manual - 109 -
HLP-SP110 Series

C06.1*Analoge Input VI

Parameters for configuring the scaling and limits for analog input VI.

Par. No. Name Range Unit Default


C06.10 Terminal VI Low Voltage 0.00~C06.11 V 0.07
C06.11 Terminal VI High Voltage C06.10~10.00 V 10.00
C06.12 Terminal VI Low Current 0.00~C06.13 mA 0.14
C06.13 Terminal VI High Current C06.12~20.00 mA 20.00
Terminal VI Low Ref./ -4999.000 ~
C06.14 0.000
Feedb. Value 4999.000
Terminal VI High Ref./ -4999.000 ~
C06.15 50.000
Feedb. Value 4999.000

C06.10is used to set low voltage input;C06.12is used to set low current
input; The low voltage and current analog input scaling value corresponds
to the lowref./feedb. value, set in C06.14.
C06.11is used to set high voltage input;C06.12is used to set high
current input; The high voltage and current analog input scaling value
corresponds to the high ref./feedb. value, set in C06.15.
There are 4 kind of curves between terminal VI input voltage/current and
its scale value:

Ref./Feedb.

VI Input

and

- 110 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Ref./Feedb.
参考值/反馈值
C06.15

C06.10
/C06.12
0
C06.11 10V/ VI Input
VI模拟量值
/C06.13 20mA
C06.14

and

Ref./Feedb.
参考值/反馈值

C06.14

C06.15
0
C06.10 C06.11 10VI VI Input
VI模拟量值
/C06.12 /C06.13 20mA

and

Ref./Feedb.

VI Input

and

HLP-SP110 Series Operating Manual - 111 -


HLP-SP110 Series

Terminal VI reference/feedback value calculated as follows:


If C06.10 <= VI Input<= C06.11,
VI Ref./Feedb.Value = (C06.15 - C06.14) ÷ (C06.11 - C06.10) × (VI input
- C06.10) + C06.14;
If VI Input< C06.10,
VI Ref./Feedb.Value= C06.14;
If VIInput> C06.11,
VI Ref./Feedb.Value= C06.15;
Note: Above formulasare for voltage input.If it is a current input, C06.10
and C06.11 use C06.12 and C06.13 instead respectively.

Par. No. Name Range Unit Default


C06.16 Terminal VI Filter Time 0.01~10.00 s 0.01

Enter the terminal VI filter time. This is a first-order digital low pass
filter for suppressing electrical noise in terminal VI.A high time constant
value improves dampening but also increases the time delay through the
filter.

Par. No. Name Range Unit Default


C06.18 Terminal VI Zero Dead Band 0.0~20.00 V/mA 0.00

Set the dead-band of VI at 0 speed. When analog input VI ref. low and
ref. high have opposite signs, there must be a set point that corresponding
to an analogue value equals 0. In order to prevent the set point jitter
at zero point due to analog interference, this parameter should be set
properly.

Ref./Feedb.
C06.15

B
0 A C
VI Input

C06.18
C06.14

Point A as shown in the figure is the analog value that corresponds to


a setpoint that equals 0. It is calculated via analog low, high values and
low, high reference/feedback values. After setterminal VI zero dead
band, UAB=UAC=C06.18/2. If the VI input is between B and C, the VI
reference/feedback is 0.

- 112 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par. No. Name Range Unit Default


0: Voltage mode
C06.19 Terminal VI Mode 0
1: Current mode

Select the input to be present on analog input VI.

C06.2* Analog Input AI

Par. No. Name Range Unit Default

Terminal AI Low
C06.20 0.00~C06.21 V 0.07
Voltage
Terminal AI High
C06.21 C06.20~10.00 V 10.00
Voltage
Terminal AI Low
C06.22 0.00~C06.23 mA 0.14
Current
Terminal AI High
C06.23 C06.22~20.00 mA 20.00
Current
Terminal AI Low
C06.24 -4999.000~4999.000 0.000
Ref./Feedb. Value
Terminal AI High
C06.25 -4999.000~4999.000 50.000
Ref./Feedb. Value
Terminal AI Filter
C06.26 0.01~10.00 s 0.01
Time
Terminal AI Zero
C06.28 0.0~20.00 V/mA 0.00
Dead Band
0: Voltage mode
C06.29 Terminal AI Mode 1: Current mode 0
2: Resisitor(RI) mode

C06.30 AI low input resistor 0.0 ~ 400.0 Ω 0.00

C06.31 AIhighinputresistance 0.0 ~ 600.0 Ω 400.0

The usage of terminal AI is similar to terminal VI, please refer to C06.1*


Analog Input VI.

Whenresistor signal enter into AI terminal, we need set C6.29 is 2 and


connect connector to RI;
Wiring scheme refer to under chart

HLP-SP110 Series Operating Manual - 113 -


HLP-SP110 Series

C06.7* Analog Output VO

Par. No. Name Range Unit Default


0: 0-20mA
C06.70 Terminal VO Mode 1: 4-20mA 3
3: 0-10V

Select output to be present on analog output VO.


Attention: This parameter is in relation with the jumper switch, if voltage
output is selected, junmperswithJ2 leg1, 2 should be asserted on; if
current output is selected, junmperswithJ2 leg2, 3 should be asserted on.

Par. No. Name Range Unit Default

C06.71 Terminal VO Analog Output 0~23 0

Select choices of the analog output VO.

Option Function Scale

0 No Function

10 Output Frequency 0% = 0Hz, 100% = 200Hz

If C03.00 = 0,
then 0% = 0, 100% = C03.03;
11 Reference
If C03.00 = 1,
then 0% = -C03.03, 100% = C03.03;

12 Feedback
13 Output current 0% = 0, 100% = C16.37
16 Power 0% = 0, 100% = C01.20

- 114 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

17 Speed 0% = 0, 100% = C01.25


18 Motor Voltage 0% = 0, 100% = C01.22
20 Bus Control
0% = C06.10/C06.12,
22 Terminal VI Input
100% = C06.11/C06.13

0% = C06.20/C06.22,
23 Terminal AI Input
100% = C06.21/C06.23

Par. No. Name Range Unit Default


Terminal VO Output Min.
C06.73 0.00~200.00 % 0.00
Scale
Terminal VO Output Max.
C06.74 0.00~200.00 % 100.00
Scale

Scale minmum/maximum output of selected ananlog signal at terminal


VO as percentage of minmum/maximum signal value.
VO Output Min./Max. is related with VO mode:

VO Mode VO Output Min. VO Output Max.


0~20mA 0mA 20mA
4~20mA 4mA 20mA
0~10V 0V 10V

Par. No. Name Range Unit Default

Terminal VO
C06.75 0.00~C06.76 % 0.00
Min Output
Terminal VO Voltage mode: C06.75~10.00
C06.76 % 10.00/20.00
Max Output Current mode: C06.75~20.00

These two parameters is used to set VO min and max value for terminal VO,.
Example:
Under speed open mode, set C03.03 =50.000,C06.70 = 3(0 ~ 10V),
     C06.71 = 10(output frequency, 0% = 0Hz, 100% = 50Hz),
     C06.73 = 0.00%(0Hz),C06.74= 100.00%(50Hz),
     C06.74 = 100.00%(50Hz), C06.75 = 2V,C06.76 = 8V
Relationship betweenoutput frequencyandoutputvoltageVOis shown
below:

HLP-SP110 Series Operating Manual - 115 -


HLP-SP110 Series

VO

8V

2V

0Hz 50Hz 200Hz Fout


If C06.73 = 80.00% , (40Hz) , C06.74 = 10.00% (5Hz)
Relationship betweenoutput frequencyandoutputvoltageVOis shown
below:
VO

8V

2V

5Hz 40Hz 200Hz Fout

C06.8* LCP Potentiometer

The LCP Potentiometer can be select either as reference resource or


relative reference source.

Par. No. Name Range Unit Default

C06.81 LCP Pot. Min. Ref. -4999.000~4999.000 0.000

C06.82 LCP Pot. Max. Ref. -4999.000~4999.000 50.000

These parameters are used to set the minimum/maximum reference of


LCP Potentiometer. The reference of LCP potentiometer's per division
depends on the set of the C00.47 LCP potentiometer step.

C06.9* Analog Output AO

Par. No. Name Range Unit Default


0: 0-20mA
C06.90 Terminal AO Mode 0
1: 4-20mA

- 116 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C06.91 Terminal AO Analog Output 0~23 0

C06.93 Terminal AO Output Min. Scale 0.00~200.00 % 0.00

C06.94 Terminal AO Output Max. Scale 0.00~200.00 % 100.00

C06.95 AO min output 0.00~C06.96 0


Current mode:
C06.96 AO max output 20.00
C06.95~20.00

The usage of terminal AO is similar to terminal VO, please refer to


C06.7* Analog Output VO.

6.8 Group 07: Controllers


C07.1* Torque PI Control
Parameters for configuring the torque PI control in torque open loop
(C01.00 Configuration Mode).

Par. No. Name Range Unit Default

C07.12 Torque PI Proportional Gain 0~500 % 100

Enter the proportional gain value for the torque controller. Selection of a
high value makes the controller react faster. Too high a setting leads to
control instability.

Par. No. Name Range Unit Default

C07.13 Torque PI Integration Time 0.002~2.000 s 0.020

Enter the integration time for the torque controller. Selection of a low
value makes the controller react faster. Too low a setting leads to control
instability.

C07.2* Process PID Feedback

Par. No. Name Range Unit Default


0: No function
1: Terminal VI
Process PID Feedback
C07.20 2: Terminal AI 0
Source
8: Pulse input DI4
11: Local bus

Select source of feedback signal.

HLP-SP110 Series Operating Manual - 117 -


HLP-SP110 Series

C07.3* Process PID Control

This parameter is active in closed loop process control mode (See C01.00
Configuration Mode).

Par. No. Name Range Unit Default


Process PID Normal/ 0: Normal
C07.30 0
Inverse 1: Inverse

Normal and inverse control are implemented by introducing a difference


between the reference signal and the feedback signal.
0: Normal, the drive is to reduce/increase the output frequency if the
feedback signal is larger/lower than reference;
1: Inverse, the drive is to reduce/increase the output frequency if the
feedback signal is lower/larger than reference;

Par. No. Name Range Unit Default


0: Disable
C07.31 Process PID Anti Windup 0
1: Enable

This function ensures the output frequency reaches to frequency limit.


PID-controller will be initialized to the current frequency when the
output frequency can not be changed. This can prevent the integrator
continue to integrate on an error when the PID-controller can’t adjust
output frequency.
0: Disable, continue regulation of a given error even when the output
frequency can’t be increased/decreased;
1: Enable, ceases regulation of a given error when the output
frequency can’t be increased/decreased;

Par. No. Name Range Unit Default


C07.32 Process PID Start 0.0~200.0 Hz 0.0

Enter the motor speed to be attained as a start signal for commencement


of PID control. When the power is switched on, the drive will commence
ramping and then operate under speed open loop control. Thereafter,
when the Process PID Start Speed is reached, the drive will change over
to Process PID Control.

- 118 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Output
Frequency
Speed open loop Process closed loop

C07.32

ON Time
Start OFF OFF
Command

Par. No. Name Range Unit Default


C07.33 Process PID Proportional Gain 0.00~10.00 0.01
Enter the PID proportional gain. The proportional gain multiplies the
error between the set point and the feedback signal.
Attention: This function is disabled when it is set to “0”.

Par. No. Name Range Unit Default


C07.34 Process PID Integral Time 0.10~9999.00 s 9999.00
Enter the PID integral time. The integrator provides an increasing gain
at a constant error between the set point and the feedback signal. The
integral time is the time needed by the integrator to reach the same gain
as the proportional gain.

Par. No. Name Range Unit Default


C07.35 Process PID Differentiation Time 0.00~10.00 s 0.00
Enter the PID differentiation time. The differentiator does not react
to a constant error, but provides a gain only when the error changes.
The shorter the PID differentiation time, the stronger the gain from the
differentiator.

Par. No. Name Range Unit Default


C07.38 Process PID Feed Forward Factor 0~400 % 0
Enter the PID feed forward (FF) factor. The FF factor sends a constant
fraction of the reference signal to bypass the PID control, so the PID
control only affects the remaining fraction of the control signal. Any
change to this parameter will thus affect the motor speed. When the FF
factor is activated it provides less overshoot, and high dynamics when
changing the set point.

HLP-SP110 Series Operating Manual - 119 -


HLP-SP110 Series

Par. No. Name Range Unit Default


C07.39 On Reference Bandwidth 0~200 % 0
Enter the On Reference Bandwidth. When the PID Control Error (the
difference between the reference and the feedback) is less than the set
value of this parameter, the PID control stops.

Par. No. Name Range Unit Default


C07.41 Process PID Output Low -100~100 % 0
C07.42 Process PID Output High -100~100 % 100
0:set valu
1:VI
C07.45 Feed forward factor source 2:AI 0
11: Local bus
21:LCP
Feed forward factor control 0:Positive logic
C07.46 0
mode 1:Anti logic
C07.50 I Integral limit 100.00~100.00 % 0..00
C07.51 I Integral term limit 100.00~100.00 % 100.00
0:Mode0
C07.55 Bandwidth control mode 1:Mode1 0
2:Mode2

These parameters are used to set process PID controller output low/high
limit, 100% corresponds to C04.19.

- 120 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

6.9 Group 08: Communication


C08.0* Comm. General Settings

Par. No. Name Range Unit Default


0: Digital and control
word
C08.01 Control Site 0
1: Digital only
2: Control word only

The drive start, stop, reverse, jog commands can be given both through
digital input terminals and communication control word, this parameter
is used to set the drive control command site.
Communication control word is the control command sent by drive,
it is 16-bit fixed-length (a word). It can be set by written register (address
2809) or coils (address 0~15) via ModBus or FC protocol. For the
meaning of control word each bit, please refer to register 2810 and coils
0~15 description in appendix A Modbus Communication Specification.
0: Digital and control word, control by using both digital input
andcontrol word;
1: Digital only, control by using digital inputs only;
2: Control word only, control by using control word only;

Par. No. Name Range Unit Default


0: Disable
C08.02 Control Word Selection 1
1: Enable

This parameter is used to select whether the control word is active or not.

Par. No. Name Range Unit Default


C08.03 Control Word Timeout Time 0.1~6500.0 s 1.0

Enter the maximum time expected to pass between the reception of two
consecutivetelegrams. If this time is exceeded, it indicates that the serial
communicationhas stopped. The function selected in C08.04 Control
Word Timeout Function willthen be carried out. The time-out counter is
triggered by a valid control word.

HLP-SP110 Series Operating Manual - 121 -


HLP-SP110 Series

Par. No. Name Range Unit Default


0: Off
1: Freeze output
Control Word 2: Stop
C08.04 0
Timeout Function 3: Jogging
4: Max. speed
5: Stop and trip
Select the time-out function. The time-out function activates when
the control word fails to be updated within the time period specified in
C08.03 Control Word Timeout Time.
0: Off, resumes control via serial bus using the most recent control
word;
1: Freeze output, frozen at the present value;
2: Stop, overruled to stop;
3: Jogging, overruled to jog speed;
4: Max. speed, overruled to max.speed;
5: Stop and trip, overruled to stop with subsequent trip (“E.17”).

Par. No. Name Range Unit Default


0: Do not reset
C08.06 Reset Control Word Timeout 0
1: Do reset

Resetting control word timeout will remove any timeout function. After
control word timeout occurs, a control word interrupt flag will be within
the drive. It must be use the parameter to clear the flag (Do reset), else
even to restore communication or clear "E.17" alarm, the drive will
continue to report control word timeout.
0: Do not reset, control word timeout is not reset;
1: Do reset, control word timeout is reset;

Par. No. Name Range Unit Default


0: Off
C08.20 Diagnostic function 0
1: On
The parameters will enable internal diagnostic function.

- 122 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C08.3* Port Setting

Par. No. Name Range Unit Default


0: FC
C08.30 Protocol 2: Modbus RTU 2
6: Modbus ASCII
Select the protocol to be used.

Par. No. Name Range Unit Default


C08.31 Address 0~247 1

Select the address for the bus. FC-bus range is 1-126, and Modbus range
is 1-247.

Par. No. Name Range Unit Default


0: 2400
1: 4800
2: 9600
3: 19200
C08.32 Baud Rate 4: 38400 bit/s 2
5: 57600
6: 76800
7: 115200
8~9: Reserved
Select baud rate for communication.

Par. No. Name Range Unit Default


0: Even parity (1 stop bit)
1: Odd parity (1 stop bit)
C08.33 Parity/Stop Bits bit/s 0
2: No parity (1 stop bit)
3: No parity (2 stop bit)

This parameter only effective for Modbus and FC bus always has even
parity.

Par. No. Name Range Unit Default


C08.35 Min. Response Delay 0.000 - 0.500 s 0.002

Specify the minimum delay time between receiving a request and


transmitting a response. This is used for overcoming modem turnaround
delays.

HLP-SP110 Series Operating Manual - 123 -


HLP-SP110 Series

Par. No. Name Range Unit Default


C08.36 Max. Response Delay 0.010~10.000 s 5.000

Specify the maximum permissible delay time between transmitting a


request and receiving a response. If exceeds this delay time, the drive
will not respond to received data.
Par. No. Name Range Unit Default
0: Normal
Message
C08.38 1: Only response exception message 0
Response
2: Not response

This parameter is used to control Modbus message response.


Attention: the drive will response the READ instruction no matter what
C08.38 set.

Par. No. Name Range Unit Default


Modbus Parameter 0: Not saved at power down
C08.39 0
Write Store 1: Saved at power down
This parameter is used to control whether the parameters which is
changed by Modbus WRITE instruction are saved or not at power down.

C08.5* Digital/Bus
This parameter only active only when C08.01 Control site is set to [0]
digital and control word.

Par. No. Name Range Unit Default


C08.50 Coasting Select 3
C08.53 Start Select 0: Digital input 3
1: Bus
C08.54 Reversing Select 3
2: Logic AND
C08.55 Set-up Select 3: Logic OR 3
C08.56 Preset Reference Select 3

Select control of the coasting, start, reverse, set-up and preset reference
function via the terminals (digital input) and/or via the bus.
0: Digital input, activate via a digital input;
1: Bus, activate via serial communication port;
2: Logic AND, activate via serial communication port and a digital
input;
3: Logic OR, activate via serial communication port or a digital
input;

- 124 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

6.10 Group 13: Simple PLC


SimplePLC is a user-defined sequence of operation (C13.52[x]). When the
associated user-defined envents(C13.51[x]) is set to true, Sample PLC will
perform these operations.
Events and related operations are paired, that is , once an event is “true”,
will execute its associated action. You can set up to 54 events and
operations.
Start and stop simple PLC: Selects order or parallel control in C13.00
Sample PLC Mode, when start event (C13.01) is “true”, start simple
PLC, when stop event (C13.02) is “true”, simple PLC will be stopped. In
addition, you can also choose [0] off (C13.00) to stop the simple PLC.
Attention: Simple PLC function is only valid in AUTO mode.

C13.0* Simple PLC Settings

Par. No. Name Range Unit Default


0: Off
C13.00 Simple PLC Mode 1: Order execution 0
2: Parallel execution

Set the simple PLC control mode.


0: Off;
1: Order execution, after simple PLC start event is "true", the control
event executes orderly: from the control event 0 (C13.51[0]) to control
events n (C13.51[N], N is the last non-empty event) and then back to
control event 0, as shown in the following figure:

2: Parallel execution, after simple PLC start event is "true", the


control event executes parallelly: control event 0~N executes at the same
time (cycle) , as shown in the following figure:

HLP-SP110 Series Operating Manual - 125 -


HLP-SP110 Series

Par. No. Name Range Unit Default


C13.01 Start Event 0~54 39

Enter the simple PLCstart event.


0: False, enter the fixed value - FALSE;
1: True, enter the fixed value - TRUE;
2: Running, the motor is running;
3: In current range-No warning, The motor is running within the
programmed current ranges set in C04.50 Warning Current Low and
C04.51 Warning Current High, and no warning is present;
4: On reference-No warning, the motor is running on reference,and
no warning is present;
7: Out of current range, output current is outside the range set in
C04.50 and C04.51;
8: Below current low, output current is lower than set in C04.50;
9: Above current high, output current is higher than set in C04.51;
10: Out of frequency range, output frequency is outside the range set
in C04.52 and C04.53;
11: Below frequency low, output frequency is lower than set in
C04.52;
12: Above frequency high, output frequency is higher than set in
C04.53;
13: Out of feedback range, feedback is outside the range set in
C04.56 and C04.57;
14: Below feedback low, feedback is lower than set in C04.56;
15: Above feedback high, feedback is higher than set in C04.57;
16: Thermal warning, a thermal warning occurs;
17: Mains out of range, over-voltage or under-voltage occurs;
18: Reversing, the drive runs in counter clockwise;
19: Warning, if the drive issues a warning, this event is TRUE;
20: Alarm (trip), if the drive alarms and trip is actived, this event is
TRUE;
21: Alarm (trip lock), if the drive alarms and trip lock is actived, this
event is TRUE;
22: Comparator 0, output of comparator 0 is used in logic rules;

- 126 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

23: Comparator 1, output of comparator 1 is used in logic rules;


24: Comparator 2, output of comparator 2 is used in logic rules;
25: Comparator 3, output of comparator 3 is used in logic rules;
26: Logic rule 0, result of logic rule 0 is used in logic rules;
27: Logic rule 1, result of logic rule 1 is used in logic rules;
28: Logic rule 2, result of logic rule 2 is used in logic rules;
29: Logic rule 3, result of logic rule 3 is used in logic rules;
30: Simple PLC time-out 0, result of timer 0 is used in logic rules;
31: Simple PLC time-out 1, result of timer 1 is used in logic rules;
32: Simple PLC time-out 2, result of timer 2 is used in logic rules;
33: Terminal FOR, input value entered via terminal FOR is used in
logic rules;
34: Terminal REV, input value entered via terminal REV is used in
logic rules;
35: Terminal DI1, input value entered via terminal DI1 is used in
logic rules;
36: Terminal DI2, input value entered via terminal DI2 is used in
logic rules;
37: Terminal DI3, input value entered via terminal DI3 is used in
logic rules;
38: Terminal DI4, input value entered via terminal DI4 is used in
logic rules;
39: Start command, if the drive starts in any way, this event is
TRUE;
40: Drive stopped, if the drive stops in any way, this event is TRUE;
50: Simple PLC time-out 3, result of timer 3 is used in logic rules;
51: Simple PLC time-out 4, result of timer 4 is used in logic rules;
52: Simple PLC time-out 5, result of timer 5 is used in logic rules;
53: Simple PLC time-out 6, result of timer 6 is used in logic rules;
54: Simple PLC time-out 7, result of timer 7 is used in logic rules;
Par. No. Name Range Unit Default
C13.02 Stop Event 0~54 40

Enter the simple PLC stop event. For options, see C13.01 Start Event.

Par. No. Name Range Unit Default


0: Do not reset
C13.03 Reset Simple PLC 0
1: Do reset

0: Do not reset, retains programmed settings in all group 13


parameters;
1: Do reset, resets all group 13 parameters to default settings;

HLP-SP110 Series Operating Manual - 127 -


HLP-SP110 Series

Par. No. Name Range Unit Default


0: No function
Simple 1: Power down save
C13.04 0
PLC Store 2: Stop save
3: Both power down and stop save

This parameter is used to select whether the simple PLC state is saved or
not at power down/stop.

C13.1* Comparators
Comparators are used for comparing continuous variables (e.g. output
frequency, output current, analog input etc.) with fixed preset values. In
addition, there are some constant value in conjunction with the preset
value for comparison, please refer to options in C13.10. In each of the
scanning integral the comparator will be evaluated once. And directly
use the results (true or false). Parameters in this group are all array-type
parameter with index 0-4 . Select 0 to programme Comparator 0, select
index 1 to programme Comparator 1, and so on.
For example: Motor current is 25A, C13.10 [0] =4, C13.12 [0] =23, C13.11
[0] =2, then the output of comparator 0 is TRUE.

Par. No. Name Range Unit Default


C13.10 Comparator Operand 0~31 0

0: Disabled;
1: Reference;
2: Feedback;
3: Motor speed [Hz];
4: Motor current [A];
6: Motor power [kW];
7: Motor Voltage [V];
12: Terminal VI input, depending on your choice is current input or
voltage input;
13: Terminal AI input, depending on your choice is current input or
voltage input;
20: Fault number, please refer to chapter 8;
30: Counter A;
31: Counter B;

Par. No. Name Range Unit Default


0: Less than
C13.11 Comparator Operator 1: Approx. Equal 1
2: Greater than

- 128 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

0: Less than, if the variable selected in C13.10 is less than the set
value in C13.12, the comparator output is TRUE, else FALSE;
1: Approx. Equal, if the variable selected in C13.10 equals the set
value in C13.12, the comparator output is TRUE, else FALSE;
2: Greater than, opposite with option [0];

Par. No. Name Range Unit Default


C13.12 Comparator Value -9999.0~9999.0 0.0

Enter the “trigger level” for the variable that is monitored by this
comparator.

C13.2* Timers

Use the timer output to define an event (see C13.51) or acts as Boolean
inputs of the logic rules (see C13.40, C13.42 or C13.44).

Par. No. Name Range Unit Default


C13.20 Simple PLC Timer 0.00~3600.00 s 0.00

This parameter is an array [8] parameters with index 0 to 7. Select index


0 to Timer 0, select index 1 to Timer 1, and so on.
Timer is started by option [29]~[31], [65]~[69] in C13.52 Simple PLC
Action, and becomes TRUE if its value has exceeded the set time.

C13.4* Logic Rules


Combine up to three boolean inputs (TRUE or FALSE inputs) from
timers, comparators, digital inputs, status bits and events using the
logical operators AND, OR and NOT. C13.40, C13.42 and C13.44 are
used to select logic rule Booleans, and C13.41, C13.43 is for selecting
logic rule operators.
Caculation order: First, select three Boolean inputs from C13.40, C13.41
and C13.42 for the selected logic rule, and then the result (“TRUE or
FALSE”) as a logic boolean value, together with other two boolean inputs
got from C13.43 and C13.44 to obtain the final result of the calculation
(“TRUE or FALSE”).
All parameters in this parameter group are array [4] parameters with
index 0 to 3. Select index 0 to logic rule 0, select index 1 to logic ruler 1,
and so on.

Par. No. Name Range Unit Default


C13.40 Logic Rule Boolean 1 The same as C13.01’s 0
Select the first boolean (TRUE or FALSE) input for the selected logic
rule. Options refer to C13.01.
HLP-SP110 Series Operating Manual - 129 -
HLP-SP110 Series

Par. No. Name Range Unit Default


C13.41 Logic Rule Operator 1 0~8 0
Select the first logic operator to be used on the boolean inputs from
C13.40 Logic Rule Boolean 1 and C13.42 Logic Rule Boolean 2.
0: Disabled, ignoring C13.40 and C13.42;
1: AND, evaluates the expression [C13.40] AND [C13.42];
2: OR, evaluates the expression [C13.40] OR [C13.42];
3: AND NOT, evaluates the expression [C13.40] AND NOT [C13.42];
4: OR NOT, evaluates the expression [C13.40] OR NOT [C13.42];
5: NOT AND, evaluates the expression NOT [C13.40] AND [C13.42];
6: NOT OR, evaluates the expression NOT [C13.40] OR [C13.42];
7: NOT AND NOT, evaluates the expression NOT [C13.40] AND
NOT [C13.42];
8: NOT OR NOT, evaluates the expression NOT [C13.40] OR NOT
[C13.42];

Par. No. Name Range Unit Default


C13.42 Logic Rule Boolean 2 The same as C13.01’s 0

Select the second boolean (TRUE or FALSE) input for the selected logic
rule. Options refer to C13.01.

Par. No. Name Range Unit Default


C13.43 Logic Rule Operator 2 0~8 0

Select the second logic operator to be used on the boolean input


calculated in C13.40 Logic Rule Boolean 1, C13.42 Logic Rule Operator
1and C13.43 Logic Rule Boolean 2 and the boolean input coming from
C13.44 Logic Rule Boolean 3.
0: Disabled, ignoring C13.44;
1: AND, evaluates the expression [C13.40/C13.42] AND [C13.44];
2: OR, evaluates the expression [C13.40/C13.42] OR [C13.44];
3: AND NOT, evaluates the expression [C13.40/C13.42] AND NOT
[C13.44];
4: OR NOT, evaluates the expression [C13.40/C13.42] OR NOT
[C13.44];
5: NOT AND, evaluates the expression NOT [C13.40/C13.42] AND
[C13.44];
6: NOT OR, evaluates the expression NOT [C13.40/C13.42] OR
[C13.44];
7: NOT AND NOT, evaluates the expression NOT [C13.40/C13.42]
AND NOT [C13.44];

- 130 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

8: NOT OR NOT, evaluates the expression NOT [C13.40/C13.42] OR


NOT [C13.44];

Par. No. Name Range Unit Default


C13.44 Logic Rule Boolean 3 The same as C13.01’s 0

Select the third boolean (TRUE or FALSE) input for the selected logic
rule. Options refer to C13.01.

C13.5* Events/Actions
This group of parameter is used for setting evens or actions for Simple
PLC. All parameters in this parameter group are array [30] parameters
with index 0 to 29. Select index 0 to event/action 0, select index 1 to
event/action 1, and so on.

Par. No. Name Range Unit Default


C13.51 Simple PLC Event The same as C13.01’s 0

Select the boolean input to define the Simple PLC event. Options refer to
C13.01.

Par. No. Name Range Unit Default


C13.52 Simple PLC Action 0~69 0

Select the action corresponding to the C13.51 Simple PLC Events.


Actions are executed when the corresponding event is evaluated as true.
0: Disabled, function is disabled;
1: No action, no action is operated;
2: Select set-up 1, select set-up 1 - changes the active set-up to “1”;
3: Select set-up 2, select set-up 2 - changes the active set-up to “2”;
10: Select preset ref 0;
11: Select preset ref 1;
12: Select preset ref 2;
13: Select preset ref 3;
14: Select preset ref 4;
15: Select preset ref 5;
16: Select preset ref 6;
17: Select preset ref 7;
18: Select ramp 1;
19: Select ramp 2;
20: Select ramp 3;
21: Select ramp 4;
22: Run, issues a start command to the drive;

HLP-SP110 Series Operating Manual - 131 -


HLP-SP110 Series

23: Run reverse, issues a start reverse command to the drive;


24: Stop, issues a stop command to the drive;
27: Coast, the drive coasts immediately, all stop commands
including the coast command stop the drive;
28: Freeze output, freezes the output frequency of the drive;
29: Start timer 0;
30: Start timer 1;
31: Start timer 2;
32: Set terminal DO1 low;
33: Set terminal DO2 low;
34: Set relay 1 low;
35: Set relay 2 low;
38: Set terminal DO1 high;
39: Set terminalDO2 high;
40: Set relay 1 high;
41: Set relay 2 high;
50: Select preset ref 8;
51: Select preset ref 9;
52: Select preset ref 10;
53: Select preset ref 11;
54: Select preset ref 12;
55: Select preset ref 13;
56: Select preset ref 14;
57: Select preset ref 15;
60: Reset counter A, reset counter A to “0”;
61: Reset counter B, reset counter B to “0”;
65: Start timer 3;
66: Start timer 4;
67: Start timer 5;
68: Start timer 6;
69: Start timer 7;

- 132 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

6.11 Group 14: Special Functions


Par. No. Name Range Unit Default
2~6: 2~6kHz
7: 8kHz
C14.01 Switching Frequency 8: 10kHz kHz 1
9: 12kHz
10: 16kHz

Switching frequency has asignificant inf luence to the drive and the
motor. Select appropriate switch frequency can help to adjust acoustic
noise from the motor、power consumption and the drive efficiency. When
switching frequency increases, the consumption and the noise of the
motor are reduced, but the drive’s temperature will increase, and motor
leakage and the interference to the external device will increase; the
contrary, the opposite.

Par. No. Name Range Unit Default


0: Off
*C14.03 Overmodulation 1
1: On
The overmodulation function can obtain an output voltage greater than
mains voltage.
0: Off, disable the overmodulation function to avoid torque ripple
on the motor shaft. This feature may be useful for applications such as
grinding machines.;
1: On, connects the overmodulation function to obtain an output
voltage up to 5% greater than mains voltage. Overmodulation leads to
increased torque ripple as harmonics are increased;

Par. No. Name Range Unit Default


C14.08 Damping Gain Factor 0~200 % 96

Damping gain factor can help to improve the response speed of the DC
link of the making the DC loop signal more smooth.

C14.1* Mains On/Off


Par. No. Name Range Unit Default
0: Trip (Low sensitivity)
1: Warning (Low sensitivity)
Function
2: Disabled
C14.12 at Mains 0
4: Warning (Middle sensitivity)
Imbanlance
5: Trip (Middle sensitivity)
6: Trip (High sensitivity)

HLP-SP110 Series Operating Manual - 133 -


HLP-SP110 Series

Select actions when a mains imbalance is detected. The dection of mains


imbalance depends on load. In order to meet different applications,
different sensitivity options are set for this parameter.
0: Trip (Low sensitivity), the drive trips (reports "E.04") when a
mains imbalance is detected;
1: Warning (Low sensitivity), the drive issues a warning (reports
"A.04") but continues to run when a mains imbalance is detected;
The dection method for option [0] and [1] is low sensitive, even if a
severe mains imbalance occurs, the drive will continue to run and do not
report warning if the load is low, the drive and motor will not damage in
this occasion; The drive trips (option [0]) or issues a warning (option [1])
only the load exceeds a certain range.
2: Disabled, the drive does nothing when a mains imbalance is
detected. Be attention to use this option;
4: Warning (Middle sensitivity), the drive issues a warning (reports
"A.04") but continues to run when a mains imbalance is detected;
5: Trip (Middle sensitivity), the drive trips (reports "E.04") when a
mains imbalance is detected;
The dection method for option [4] and [5] is middle sensitive.The
drive trips (option [5]) or issues a warning (option [4]) at low frequency
and heavy loaded, or high frequency and low load.
6: Trip (high sensitivity), the drive trips (reports "E.04") when a
mains imbalance is detected;
The dection method for option [6] is high sensitive.Mains imbalance
can be detected immediately. But there is minimum risk of false positives
(generally occurs in an abnormal grid or the drive over-current protection
frequently).

Par. No. Name Range Unit Default


0: Disable
C14.16 Low Voltage Mode 0
1: Enable

If the power input voltage is low, enable low voltage mode can improve
load capacity. If the voltage is 15% lower, enable low voltage mode can
make the drive afford long-term full load; If the voltage is 20% lower, the
drive needs to down load; If the voltage is normal, do not enable the low
voltage mode, otherwise it will reduce the drive useful life.

Par. No. Name Range Unit Default


Automatic Voltage 0: Disable
C14.17 1
Regulation 1: Enable

When motor voltage 12%~20% higher than rated, motor temperature will
increase, insulation capability destroyed, the torque output is unstable,
- 134 - HLP-SP110 Series Operating Manual
HLP-SP110 Series

long-term operation will cause the motor shorten its life.


Automatic voltage regulation can automatically control the output voltage
at the motor's rated voltage when the grid voltage exceed the rated motor
voltage.
Turn off automatic voltage regulation will improve the ability of rapid
deceleration, but turn off this option need to be cautious, it will cause the
output voltage different due to different grid voltage, there is an increased
risk of heat damage to the motor.
This feature can only be turned off when in VF mode.

Par. No. Name Range Unit Default


Delay Time of Auto Restart
C14.18 0.0~3600.0 s 0.0
When Power up Again

This parameter is used to define the drive action when power up again
after power loss during running.
If it is set to 3600.0, the drive does not respond to the start command
valid upon drive power-on (for example, start terminal is ON before
power-on). The drive responds only after the start command is cancelled
and becomes valid again.
If it is set to 0.0~3599.9, the drive will respond to the start command
delaying the C14.18 setting time upon drive power-on (for example, start
terminal is ON before power-on).

C14.2* Trip Reset

Par. No. Name Range Unit Default


0: Manual reset
1~10: Auto reset 1-10 times
C14.20 Reset Mode 11: Auto reset 15 times 0
12: Auto reset 12 times
13: Infinite auto reset

Select reset function after tripping.


0: Manual reset, perform reset via “OFF”button or digital inputs;
1~10: Auto reset 1-10times, can perform 1-10 automatic resets after
trips;
11: Auto reset 15 times, can perform 15 automatic resets after trips;
12: Auto reset 20 times, can perform 20 automatic resets after trips;
13: Infinite auto reset, can perform an infinite number of automatic
resets after trips;
Once option [1] - [13] is selected, the drive will be restarted after an
alarm. If reset has been done and the running signal is active, the drive
will restart automatically. For option [1] – [12], if the drive performs a

HLP-SP110 Series Operating Manual - 135 -


HLP-SP110 Series

set number of automatic reset, fault still cannot be removed, the drive
will remaina tripstate. It needs power off and on to reset the trip after
shootingfault.
Be attention to select option [13], it may cause infinite auto reset.

Par. No. Name Range Unit Default


C14.21 Automatic Restart Time 0~600 s 10

Enter time interval from trip to start of automatic reset function after
an alarm. This parameter is active when C14.20 Reset Mode is set to
automatic reset [1]-[13].

Par. No. Name Range Unit Default


0: Normal operation
2: Initialization
C14.22 Operation Mode 0
3: Backup user settings
4: Recover user settings
0: Normal operation;
2: Initialization, initialise all the parameters except information
about the drive itself and the recorded parameters.
3: Backup user settings;
4: Recover user settings;
For option [3] to [4], after modifying the drive parameters based on
the functional requirements, OEM manufacturers can set C14.22 = 3 to
backup settings. If the end users modify parameters and cannot be self-
recovery, it can be recovered by setting C14.22 = 4 or pressing "OFF" key
on LCP 5 seconds (the default time, can be modified by C00.46 One Key
Recovery Time).

Par. No. Name Range Unit Default


0: Disable
C14.23 Trip lock 0
1: Enable

0: Disable, trip lock fault reset do not need power off;


1: Enable, trip lock fault reset need power off;

Par. No. Name Range Unit Default


0: Trip
C14.27 Action at Drive Fault 0
1: Warning

Select how the d r ive should react at i ner ter fault (out put shor t
circuit,over-current, earth fault or over-voltage).
0: Trip, driveissues an alarmand tripsimmediately if it detects a

- 136 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

fault;
1: Warning, when a fault occurs, drive issues a warning and stops
the PWM outputs, and repeatlly try to open the normal PWM, if the fault
still can’t be removed, the drive issues an alarm and trips.

C14.3* Current Limit Control


The drive contains two current limit controllers. The two controllers
will be enabled when the current is over C04.18 current limit.Current
controller1 controls current by reducing the output frequency, and current
controller2 controls current by reducing the output voltage. Typically
only recommended to use current controller1, if it is still unable to control
the current in some occasions (such as fast acceleration and deceleration),
you can use the current controller2.

Par. No. Name Range Unit Default


Current Controller 1
C14.30 0~300 % 100
Proportional Gain
Current Controller 1
C14.31 0.005~2.000 s 0.020
Integration Time
C14.32 Current Controller Filter Time 2.0~100.0 ms 10.0
Current Controller 2
C14.33 0~300 % 0
Proportional Gain
Current Controller 2
C14.34 0.001~2.000 s 0.020
Integration Time

It can adjust the dynamic response characteristics of the cur rent


controllers by setting the proportional gain and integration time.
Choose a higher value of proportional gain and lower integration time
causes the controller response more quickly, but too high value of
proportional gain and tow low value of integration time will cause the
controller unstable.

C14.4* Energy Optimising

Par. No. Name Range Unit Default


*C14.40 VT Level 40~90 % 90

Enter the level of motor magnetisation at low speed. Selection of a low


value reduces energy loss in the motor, but also reduces load capability.

HLP-SP110 Series Operating Manual - 137 -


HLP-SP110 Series

Par. No. Name Range Unit Default


*C14.41 AEO Min. Magnetisation 40~75 % 66

Enter the minimum allowable magnetisation for AEO. Selection of a low


value reduces energy loss in the motor, but can also reduce resistance to
sudden load changes.

Par. No. Name Range Unit Default


0: Off
*C14.50 RFI Filter Selection 1: On 1
2: Reserved

0: Off, only the power supply is IT mains system can select [0] Off.
In this mode, the linkage can be reduced;
1: On, to ensure the drive meets EMC standards, select [1] On;
2: Reserved;
Attention: The RFI Filter selection in the model (<=22kW) is not
controlled by this parameter, but selected by screwing off/on the RFI
switch.

Par. No. Name Range Unit Default


0: Off
*C14.51 DC Link Compensation 0
1: On
This function ensures the output voltage is independent of any voltage
f luctuations in the DC link. Low torque ripple. In some cases, this
dynamic compensation may cause resonance problems in DC link circuit
and then this function should be disabled.

- 138 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

6.12 Group 15: Drive Information


C15.0* Operating Data

Par. No. Name Range Unit Default


C15.00 Operating Days 0~9999 d

View how many days the drive has run. The value is saved automatically
at power off and can’t be reset.

Par. No. Name Range Unit Default


C15.01 Running Hours 0~60000 h

View how many hours the motor has run. Reset the counter in C15.07
Reset Running Hours Counter.

Par. No. Name Range Unit Default


C15.02 kWh Counter 0~65535 kWh

View the power consumption of the motor as a mean value over one hour.
Reset the counter in C15.06 Reset kWh Counter.

Par. No. Name Range Unit Default


C15.03 Power Up’s 0~2147483647

View the number of times the drive has been powered up. This parameter
can’t be reset.

Par. No. Name Range Unit Default


C15.04 Over Temperatures 0~65535

View the number of the drive temperature faults that have occurred. This
parameter can’t be reset.

Par. No. Name Range Unit Default


C15.05 Over Voltages 0~65535

View the number of drive over-voltages that have occurred. This


parameter can’t be reset.

Par. No. Name Range Unit Default


0: Do not reset
C15.06 Reset kWh Counter 0
1: Do reset

HLP-SP110 Series Operating Manual - 139 -


HLP-SP110 Series

0: Do not reset;
1: Do reset, kWh counter is reset to zero (see C15.02 kWh Counter);
Attention: This parameter can’t be set via local bus.

Par. No. Name Range Unit Default


Reset Running 0: Do not reset
C15.07 0
Hours Counter 1: Do reset

0: Do not reset;
1: D o r e s e t , r u n n i n g h o u r s c o u n t e r i s r e s e t t o z e r o (s e e
C15.01Running Hours);
Attention: This parameter can’t be set via local bus.

C15.3* Fault Log

Par. No. Name Range Unit Default


C15.30 Alarm Code 0~255

View the alarm code and look up its meaning in chapter 8. This parameter
is an array [10] parameters. It contains aalarm log showing reasons for
the ten latest trips. C15.30[0] represents the latest, C15.30[9] is a recent
10th, this parameter cannot be reset.

Par. No. Name Range Unit Default


C15.31 Internal Fault Reason -32767~32767

T his parameter cont ai ns i nter nal fault reasons, mostly used i n


combination with alarm E.38.

Par. No. Name Range Unit Default


C15.38 Warning Code 0~255

View the warning code and look up its meaning in chapter 8. This
parameter is an array [10] parameters. It contains a warning log showing
reasons for the ten latest warnings. C15.38[0] represents the latest,
C15.38[9] is a recent 10th, this parameter cannot be reset.

C15.4* Drive Identification

Par. No. Name Range Unit Default


C15.43 Software Version

View the software version of the drive.

- 140 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

6.13 Group 16: Data Readouts


This parameter group is read-only.

C16.0* General Status

Par. No. Name Range Unit Default


C16.00 Control Word 0~65535

View latest valid control word that sent to the drive via local bus.Turn
it into 16-bit binary code. For the meaning of eachbits, please refer
to register 2809 and coils 0~15 description in appendix A Modbus
Communication Specification.

Par. No. Name Range Unit Default


C16.01 Reference -4999.000~4999.000

View the actual reference.

Par. No. Name Range Unit Default


C16.02 Reference -200.0~200.0 %

View the actual reference in percentage.

Par. No. Name Range Unit Default


C16.03 Status Word 0~65535

View active status word, the following shows the definition for each bit.

Communication Status Word


Bit 0 1
Bit00 Control Not Ready Control Ready
Bit01 Drive Not Ready Drive Ready
Bit02 Coasting Enabled
Bit03 No Error Trip
Bit04 Error Error Without Trip
Bit05 Undefined Undefined
Bit06 No Error Trip
Bit07 No Warning Warning
Bit08 Not On Reference On Reference
Bit09 Local Control Remote Control

HLP-SP110 Series Operating Manual - 141 -


HLP-SP110 Series

Frequency Not In
Bit10 Frequency In Range
Range
Bit11 Stop Running
Brake Resistor Is
Bit12 Brake Resistor Fault
Normal
Bit13 Voltage Limit Out Of Voltage Limit
Bit14 Undefined Undefined
Bit15 No Terminal Warning Terminal Warning

Par. No. Name Range Unit Default


0: Set-up 1
C16.04 Active Set-up 1: Set-up 2
2: Multi Set-up

View the drive active set-up.

Par. No. Name Range Unit Default


C16.05 Motor Speed 0~9999 rpm

View motor speed.

Par. No. Name Range Unit Default


C16.09 Custom Readout 0.00~9999.00

View the value of user-defined readout corrected from C00.31, C00.32


and C04.14.

C16.1* Motor Status

Par. No. Name Range Unit Default


C16.10 Output Power 0.000~1000.000 kW

View output power in kW.

Par. No. Name Range Unit Default


C16.11 Output Power 0.000~1000.000 hp

View output power in hp.

Par. No. Name Range Unit Default


C16.12 Motor Voltage 0~65535 V
View motor phase voltage.

- 142 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par. No. Name Range Unit Default


C16.13 Output Frequency 0.0~400.0 Hz

View output frequency.

Par. No. Name Range Unit Default


C16.14 Output Current 0.00~655.35 A

View motor phase current.

Par. No. Name Range Unit Default


C16.15 Output Frequency 0.0~200.0 %

View actual output frequency in percentage.

Par. No. Name Range Unit Default


C16.16 Output Torque -65535.0~65535.0 Nm

View actual output Torque.

Par. No. Name Range Unit Default


C16.18 Motor Thermal 0~100 %

View calculated thermal motor load which is set as percentage of


estimated thermal motor load.

C16.3* Drive Status

Par. No. Name Range Unit Default


C16.30 DC Link Voltage 0~65535 V

View DC-link voltage.

Par. No. Name Range Unit Default


C16.34 IGBT Temperature 0~65535 ℃

View the temperature of drive’s IGBT Temperature.

Par. No. Name Range Unit Default


C16.35 Drive Thermal 0~255 %

View calculated drive thermal load, which is set as a percentage of


estimated drive thermal load.

HLP-SP110 Series Operating Manual - 143 -


HLP-SP110 Series

Par. No. Name Range Unit Default


C16.36 Drive Nominal Current 0.00~1200.00 A

View the drive nominal current.

Par. No. Name Range Unit Default


C16.37 Drive Max. Current 0.00~2400.00 A

View the drive maximum current.

Par. No. Name Range Unit Default


C16.38 Simple PLC State 0~255

View the state of the event under execution by the simple SLC.

C16.4* Application Message

Par. No. Name Range Unit Default


C16.48 Power Board Temperature -128~127 ℃
View the rectifier temperature, only active in >=90kW model.

Par. No. Name Range Unit Default


C16.49 Rectifier Temperature -128~127 ℃
View the rectifier temperature, only active in >=90kW model.

C16.5* Ref./Feedb.

Par. No. Name Range Unit Default


C16.50 Main Reference -200.0~200.0 %

View sum of all external references in percentage.

Par. No. Name Range Unit Default


C16.52 Feedback -4999.000~4999.000

View the feedback value.

- 144 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C16.6*, C16.7* Inputs and Outputs

Par. No. Name Range Unit Default


C16.60 Digital Input 0~65535

View signal states from active digital inputs, which indicates in a 16-bit
binary code. If the drive detects digital input terminals connected, the
corresponding position is set to “1”, otherwise “0”. Digital input terminal
and the corresponding relationship between the binary code are as below:

Bin Term. Bin Bin


Binary Term. No. Term. No. Term. No.
ary No. ary ary
bit0 FOR bit4 DI3 bit8 Reserved bit12 Reserved
bit1 REV bit5 DI4 bit9 Reserved bit13 Reserved
bit2 DI1 bit6 Reserved bit10 Reserved bit14 Reserved
bit3 DI2 bit7 Reserved bit11 Reserved bit15 Reserved

Par. No. Name Range Unit Default


0: 0~20mA
C16.61 Terminal VI Setting
1: 0~10V

View actual state of analog input VI

Par. No. Name Range Unit Default


C16.62 Analog Input VI 0.00~20.00 V/mA

View actual input voltage or current value on analog input VI.

Par. No. Name Range Unit Default


0: 0~20mA
C16.63 Terminal AI Setting
1: 0~10V

View actual state of analog input AI.

Par. No. Name Range Unit Default


C16.64 Analog Input AI 0.00~20.00 V/mA

View actual input voltage or current value on analog input AI.

HLP-SP110 Series Operating Manual - 145 -


HLP-SP110 Series

Par. No. Name Range Unit Default


C16.65 Analog Output VO 0.00~20.00 V/mA

View input frequency on pulse input terminal DI4.

Par. No. Name Range Unit Default


C16.66 Digital Output 0~255

View actual state of digital output, which indicates in a 4-bit binary code;
If the digital output terminal is active, the corresponding position is set
to “1”, otherwise “0”. Corresponding relationship betweenstate of the
digital output terminals and the binary code are as below:

Binary bit3 bit2 bit1 bit0


Term. No. Reserved Reserved DO2 DO1

Par. No. Name Range Unit Default


C16.71 Relay Output 0~65535

View the output status of the relay, the corresponding bit is set to
“1”whenthe relay output is active, otherwise it will be set to “0”.

Binary bit1 bit0


Item. No. Relay 2 Relay 1

Par. No. Name Range Unit Default


C16.72 Counter A 0~2147483647

View present value of counter A.

Par. No. Name Range Unit Default


C16.73 Counter B 0~2147483647

View present value of counter B.

- 146 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Par. No. Name Range Unit Default


C16.78 Analog Output AO 0.00~20.00 mA

View actual output current on analog output AO.

C16.8* Field bus/FC Port

Par. No. Name Range Unit Default


C16.86 Communication Reference -32768~32767

View the last received reference from communication.

C16.9* Diagnosis Readouts

Par. No. Name Range Unit Default


C16.90 Alarm Word 1 0~0xFFFFFFFFUL
C16.91 Alarm Word 2 0~0xFFFFFFFFUL
C16.92 Warning Word 1 0~0xFFFFFFFFUL
C16.93 Warning Word 2 0~0xFFFFFFFFUL

View the alarm/warning word sent via the serial communication port in
hex code. Convert this parameter to a 32-bit binary code, definition of
the bits in word showed in the table below, among which that reserved by
manufacturers are undefined bits:
Alarm Word1 Alarm Word 2 Warning Word 1 Warning Word 2
Bit
/C16.90 /C16.91 /C16.92 /C16.93
0 Brake Detect Undefined Undefined Undefined
Power Card Over Power Card Over
1 Undefined Undefined
Temp. Temp.
2 Earth Fault Trip Earth Fault Undefined
3 Reserved Option Part Undefined Undefined
Control Card Control Card
4 Undefined Undefined
Temp Temp
5 Over Current Undefined Over Current Undefined
6 Torque Limit Undefined Undefined Undefined
Motor Over Ther- Motor Over Ther-
7 Undefined Undefined
mal mal
Motor Over Ther- Motor Over Ther-
8 Damaged Part Damaged Part
mal ETR mal ETR
9 DriveOverload Undefined Drive Overload Undefined
10 Under Volt Undefined Under Volt. Undefined

HLP-SP110 Series Operating Manual - 147 -


HLP-SP110 Series

11 Over Volt Undefined Over Volt. Undefined


External Inter-
12 Short Circuit Undefined Undefined
lock
13 Undefined Undefined Undefined Undefined
14 Mains Ph. Loss Undefined Mains Ph. Loss Undefined
15 AMA Error Undefined No Motor Undefined
16 Live Zero Error Undefined Live Zero Error Undefined
17 Internal Fault Undefined Undefined Undefined
18 Brake Overload Fan Fault Brake Overload Fan Fault
19 U Phase Loss Undefined Undefined Undefined
20 V Phase Loss Undefined Undefined Undefined
21 W Phase Loss Undefined Undefined Undefined
22 Undefined Undefined Undefined Undefined
Control Voltage
23 Undefined Undefined Undefined
Fault
24 Undefined Undefined Vdd Supply Low Undefined
25 VDD Supply Low Undefined Current Limit Undefined
Brake Resistor
26 Undefined Undefined Undefined
Error
Brake Transistor
27 Undefined Undefined Undefined
Fault
Bake Transistor
28 Undefined Undefined Undefined
Open Circuit
29 Drive Initialize Feedback Error Undefined Feedback Error

C25.0* Ref./Feedb.

Par. No. Name Range Unit Default


1:Mod e1
2:Mod e2
C25.01 Pump type 3
3:Mod e3

Parameter C5.40[0,1... 5] determines the 6 sets of relays, when the


selection is
[192], that is, as a dedicated water supply
Relay, the inverter will control the corresponding contact by selecting the
relay for the [192] For.
Option: [1] water supply mode 1, inverter up to 6 sets of relays driven by
three pumps, eachPump with two relays.
The following is the case for the two pumps:

- 148 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Set value

Pressure
sensor

Contactor2 Contactor4

Contactor1 Contactor3

[2] water supply mode 2, inverter up to 4 sets of relays driven by 4


pumps, each pump accounted for A set of relays.

[3] water supply mode 3, the inverter does not go through the relay of
the direct drive pump, the other auxiliary pump through a set of relays
connected to the grid

HLP-SP110 Series Operating Manual - 149 -


HLP-SP110 Series

Contactor1

Contactor2

Contactor3

Set value

Contactor4

Pressure test

Par. No. Name Range Unit Default


0:Use enable
C25.02 Pump enable signal 0
1:Do not use to enable
[0] all available water pumps are enable; [8] only corresponds to the

- 150 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

interlocking terminal after the pump is closed


Available; when the DI terminal is set to 160~ 165 at any value, the
terminal from ON to OFF correspondsThe pump will be shut off at once..
Par. No. Name Range Unit Default

C25.03 Pump number 0~5 0


In the constant pressure water supply, a converter can control many
pumps, through the inverter output
Switch signal control auxiliary pump start and stop.
Description: it will be based on the c25.01 and c25.02 settings for the
relay (c5.40[x]) and the end
The sub (c5.11, c5.12, c5.14, c5.13) are allocated.
The distribution of the relay, such as c25.02 = 0, will only be allocated
for the relay, and will not be divided
Allocation of input terminals. The allocation of relations sees the table
below.

REALY
C25.01 C25.03
C5.40[0] C5.40[1] C5.40[2] C5.40[3] C5.40[4] C5.40[5]

0 Replace Replace Replace Replace Replace Replace


[1]
0/Re- 0/Re- 0/Re-
(Pump 1 192 192 0/Replace
place place place
num-
0/Re-
ber 2 192 192 192 192 0/Replace
place
max3)
3 192 192 192 192 192 192

0 Replace Replace Replace Replace Replace Replace


0/Re- 0/Re- 0/Re- 0/Re-
[2] 1 192 0/Replace
place place place place
(Pump 0/Re- 0/Re- 0/Re-
num- 2 192 192 0/Replace
place place place
ber 0/Re- 0/Re-
max4) 3 192 192 192 0/Replace
place place
0/Re-
4 192 192 192 192 0/Replace
place

HLP-SP110 Series Operating Manual - 151 -


HLP-SP110 Series

0 Replace Replace Replace Replace Replace Replace


0/Re- 0/Re- 0/Re- 0/Re- 0/Re-
1 0/Replace
place place place place place
0/Re- 0/Re- 0/Re- 0/Re-
2 192 0/Replace
place place place place
[3]
0/Re- 0/Re- 0/Re-
(Pump 3 192 192 0/Replace
place place place
num-
0/Re- 0/Re-
ber 4 192 192 192 0/Replace
place place
max7)
0/Re-
5 192 192 192 192 0/Replace
place
0/Re-
6 192 192 192 192 192
place
7 192 192 192 192 192 192
”0/Replace” When the relay is located in the case of “192”, the relay is
set to 0 when it is set to other values, Replace .
Explain
C25.01 C25.02 C25.03 C5.11 C5.12 C5.13 C5.14

[1] 0 Replace Replace Replace Replace


(Pump 1 160 Replace Replace Replace
The
num- 2 160 161 Replace Replace
proposed
ber 3 160 161 162 Replace
use of FOR
max3) 4 Same 3 option as the run-
0 Replace Replace Replace Replace ning signal
[2] 1 160 Replace Replace Replace is: c5.10=8
(Pump
2 160 161 Replace Replace (default).
num- 8
3 160 161 162 Replace DI enables
ber
4 160 161 162 163 the distri-
max4) 8
5 Same 4option bution to
0 Replace Replace Replace Replace begin f rom
[3] 1 160 Replace Replace Replace the C5.11.
(Pump
2 160 161 Replace Replace
num-
3 160 161 162 Replace
ber
max7) 4 160 161 162 163
5 Same4option

Par. No. Name Range Unit Default


C25.09 Pump status display 0~65535 0

- 152 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Only read parameter,


Bit: express run pump number
Ten bit: express enable pump number
Hundred bit: express pump total number

Par. No. Name Range Unit Default


C25.13 Internal acceleration time 0.00~3600.00 S 0.00
In the course of add/dec pump, system will adjust to expected frequency
according to the acc time. If the value is smaller than 0.05, the parameter
will be invalid.

Par. No. Name Range Unit Default


C25.14 Internal deceleration time 0.00~3600.00 S 0.00
In the course of add/dec pump, system will adjust to expected frequency
according to the dec time. If the value is smaller than 0.05, the parameter
will be invalid.

Par. No. Name Range Unit Default


C25.20 Low frequency set 1 0.0~400.0 HZ 25.0
In theprocess of constant pressure water supply, When system needed
water is less, output frequency is smaller than C25.20 for system (C25.21),
correlatived output terminal is actived. Auxiliary pump is stopped. The
parameter is valid only a single auxiliary pump.

Par. No. Name Range Unit Default


C25.21 Low frequency duration 0.00~3600.00 HZ 25.0
The parameters is used with C25.20/C25.22/C25.23.

Par. No. Name Range Unit Default


C25.22 Low frequency set 2 0.0~400.0 HZ 25.0
In theprocess of constant pressure water supply, When system needed
water is less, output frequency is smaller than C25.22 for system (C25.21),
correlatived output terminal is actived. Auxiliary pump is stopped. The
parameter is valid only two auxiliary pump.

Par. No. Name Range Unit Default


C25.23 Low frequency set 3 0.0~400.0 HZ 25.0
In theprocess of constant pressure water supply, When system needed
water is less, output frequency is smaller than C25.23 for system(C25.21),
correlatived output terminal is actived. Auxiliary pump is stopped. The
parameter is valid only three auxiliary pump.

HLP-SP110 Series Operating Manual - 153 -


HLP-SP110 Series

Par. No. Name Range Unit Default


C25.25 High frequency set 1 0.0~400.0 HZ 25.0
I n theprocess of const ant pressu re water supply, W hen system
needed water is larger, output frequency is larger than C25.25 for
system(C25.26), correlatived output terminal is actived. Auxiliary pump
is run. The parameter is valid only a single auxiliary pump.

Par. No. Name Range Unit Default


C25.26 High frequency duration 0.00~3600.00 S 100.0
The parameters is used with C25.25/C25.27/C25.28.

Par. No. Name Range Unit Default


C25.27 High frequency set 2 0.0~400.0 HZ 50.0
In theprocess of constant pressure water supply, When system needed
water is larger, output frequency is larger than C25.27 for system(C25.21),
correlatived output terminal is actived. Auxiliary pump is run. The
parameter is valid only two auxiliary pump.

Par. No. Name Range Unit Default


C25.28 High frequency set 3 0.0~400.0 HZ 50.0
In theprocess of constant pressure water supply, When system needed
water is larger, output frequency is larger than C25.28 for system(C25.21),
correlatived output terminal is actived. Auxiliary pump is run. The
parameter is valid only two auxiliary pump.
Less pressure alarm
C25.30 0.0~101.0 % 0.0
pressure
Less pressure alarm
C25.31 0.00~3600.00 S 10.0
duration
When system pressure is smaller than C25.30 for some time(C25.31),
less pressure alarm is valid and correlative output terminal is valid.
Less voltage alarm reset
C25.32 0.0~101.0 % 0.1
value
Less voltage alarm reset
C25.33 0.00~3600.00 S 10.0
time
When system pressure is larger than C25.32 for some time(C25.33), Less
pressure alarm is canceled.
Overpressure alarm
C25.34 0.0~200.0 % 200.0
pressure value
Over pressure alarm
C25.35 0.00~3600.00 S 10.0
duration

- 154 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

When system pressure is larger than C25.34 for some time(C25.35), over
pressure alarm is valid and correlative output terminal is valid.

Overvoltage alarm reset


C25.36 0.0 - 200.0 % 199.0
value
Overvoltage alarm reset
C25.37 0.0 - 3600.0 S 10.0
time
When system pressure is larger than C25.36 for some time(C25.37), Less
pressure alarm is canceled.

C25.40 Pump lock time 0.00~3600.00 S 1.0


Set the parameter, it will make sure stability of relay action

The auxiliary pump


C25.42 0.00~3600.00 H 0
running time
C25.43 Change pump frequency 0.0~400.0 HZ 50.0

If C25.42 = 0, The function of change pump is canceled. When C25.42


>0, The function of change pump is started. If counted time is arrived
and output frequency is smaller than C25.43, the function of change
pump is valid.

C25.45 Start delay time 0.00~3600.00 S 1.0


The parameter is used to express delay time from stop to run.

Automatic pump time


C25.46 0~6000.0 H
display
The parameter is used to display change pump time. When C25.46 = 0,
C25.42 = 0;

Multi pump control state


C25.48 0~65535
display
The parameter is used to express terminal status for external pumpstatus .

C25.49 Relay status display 0~65535


The parameter is used to express relay status for setting 100.

HLP-SP110 Series Operating Manual - 155 -


HLP-SP110 Series

0:Invalid
C25.50 Sleep mode 0
2:Effective
[0] invalid;
[2] sleep mode valid;
If C25.50 = 0, system will not enter into sleep mode

C25.51 Sleep pressure level 0.0~150.0 % 95%


When C25.50 = 2, we set the parameter value according to the
percentage of the target value. C25.57 refer to the explanation.

C25.52 Sleep pressure duration 0.0~300.0 S 20.0


Before main pump enter into sleep status, the sleep pressure must continue
for C25.52

C25.53 Sleep frequency 0.0~400.0 HZ 20.0


Before main pump enter into sleep status, the system output frequency
wiil run for some time according to C25.53.

C25.54 Sleep frequency duration 0.0~300.0 S 20.0


Before main pump enter into sleep status, the sleep frequency must
continue for C25.52

C25.57 Wake up pressure level 0.0~150.0 % 80%


When system pressure is lower than C25.57, the sleep will drop out. we set
the parameter value according to the percentage of the target value.

- 156 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

0:Disabled
C25.85 Belt breakage detection 1:warning 0
2:Alarm
[0] Disabled;
[1] Warning;
[2] Alarm

The belt breakage detection :


C25.86 0.0~400.0 HZ 0.5
frequency value
if system need enter into belt breakage detection, system frequency will be
larger than C25.86.

The belt breakage detection:


C25.87 0.0~3000.0 A 0.0
current value
If system need enter into belt breakage detection, system current will
compare with C25.87.

The belt breakage 0:Greater than C25.87 set


C25.88 detection: current values A 0
direction detection 1:Less than C25.87 set value
The parameter is used to express current detection value.

Belt breakage
C25.89 0.0~600.0 S 20
detection: time delay
The parameter is used to express detection delay time.

HLP-SP110 Series Operating Manual - 157 -


HLP-SP110 Series

Chapter 7 Quick Application Guide


7.1 Using LCP to Start/Stop the Drive
1. Press “HAND” key on LCP to start the drive;
2. Turn the potentiometer to change output frequency;
3. Press “OFF” key on LCP to stop the drive;

7.2 Using Digital Input Terminals to Start/Stop the


Drive
Usually there are four mode for using digital input terminals to start/stop
the drive. No matter what mode, press “AUTO” key on LCP first.

7.2.1 Two-line Mode 1


It is the most commonly used two-line mode, in which the forward/
reverse rotation of the motor is decided by FOR and REV. Wiring and
parameters are set as below:
Term. Rar. Value Spec.
K1
FOR C05.10 8 Start
K2 Start reve-
REV C05.11 11
COM -rsing

K1 K2 Command
OFF OFF Stop
ON OFF Run forward
OFF ON Run reverse
ON ON Stop

7.2.2 Two-line Mode 2


In this mode, FOR is run enabled terminal, and REV determines the
running direction. Wiring and parameters are set as below:
Term. Rar. Value Spec.
K1
FOR C05.10 8 Start
K2 REV
C05.11 11 Reversing
COM

- 158 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

K1 K2 Command
OFF OFF Stop
ON OFF Run forward
OFF ON Stop
ON ON Run reverse

7.2.3 Three-line Mode 1


In this mode, FOR is run enabled terminal, and the direction is decided
by DI1 and DI2. Wiring and parameters are set as below:
Term. Rar. Value Spec.
SB1 FOR C05.10 6 Stop inverse
SB2 DI1 C05.12 9 Latched start
SB3 DI2 C05.13 37 latched
Reversing
COM

SB1 SB2 SB3 Command


OFF × × Stop
ON × Run forward
ON × Run reverse

7.2.4 Three-line Mode 2


In this mode, FOR is run enabled terminal. The RUN command is given
by DI1 and the direction is decided by DI2. Wiring and parameters are
set as below:
Term. Rar. Value Spec.
SB1 FOR C05.10 6 Stop inverse
SB2 DI1 C05.12 9 Latched start
SB3 DI2 C05.13 37 Reversing
COM

SB1 SB2 SB3 Command


OFF × × Stop
ON OFF Run forward
ON ON Run reverse

HLP-SP110 Series Operating Manual - 159 -


HLP-SP110 Series

7.3 Multi-speed
In scenarios where the running frequency of the drive need not be
adjusted continuously and only several frequencies are required, the
multi-speed control can be used. The drive supports a maximum of
16 running frequencies in each set-up, which are implemented by
state combinations of four DI terminals. Set the parameter number
corresponding to DI terminals to a value among 15 to 18 (Preset ref. bit
0~3), and then the DI terminals are specified as the multi-frequency input
terminals. The multiple frequencies are set based on the multi-frequency
table in group FC. In addition, you need to set C03.03 (Maximum
Reference). The following figure shows how to set the multi-speed
function.
Term. Par. Value State Combinations Multi-speed%
0 0 0 0 C03.10[0]
0 0 0 1 C03.10[1]
0 0 1 0 C03.10[2]

FOR C05.10 8 1 1 1 0 C03.10[14]


REV C05.11 11 1 1 1 1 C03.10[15]
0 Ref.
DI1 C05.12 15
1 ×C03.03
DI2 C05.13 16
0 DI3 C05.14 17
0 DI4 C05.15 18
COM

In the preceding figure, FOR, REV are set as two-line mode 1, DI1,
DI2, DI3 and DI4 are used as the multi-frequency input terminals, each
of which has a bit value. The state combinations of these terminals
correspond to multiple frequencies, When (DI4, DI3, DI2, DI1) = (0, 0,
1, 0), the state combination value is 2, corresponding to the value set in
C03.10[2]. The target runningfrequency is automatically calculated by
C03.10[2] x C03.03.
The drive supports a maximum of four DI terminals to be used as the
multi-frequency input terminals. You can also use less than four DI
terminals, and the empty bit is considered to be 0.

7.4 Analog Input as the Frequency Source


The VI/AI terminals can be used as the frequency source. The following
figure shows how to use the VI as the frequency source.

- 160 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Term. Par. Value Frequency Ref.Source Value


FOR C05.10 8 Characteristic
REV C05.11 11
COM Ref.
Ref.
+10V C06.10 2.00 C03.15 1
VI C06.11 8.00 C03.16 0
C06.14 5.000 C03.17 0
GND
C06.15 50.000 0 10 VI

Attention: Parameters and theirs value in dash box should be set


according to the application.

7.5 Pulse Input as the Frequency Source


The DI4 terminal can be used as pulse input. The following figure shows
how to use the pulse input as the frequency source.
Term. Par. Value Frequency Characteristic Ref.Source Value
Ref.

Ref.

Attention: Parameters and theirs value in dash box should be set


according to the application.

7.6 Speed up/down


When you need speed fine tuning at a fixed value, you can use the speed
up/down via terminals. The following figures show how to use the
function:

Term. Par. Value

FOR C05.10 8
REV C05.11 11
DI1 C05.12 21
DI2 C05.13 22
COM

HLP-SP110 Series Operating Manual - 161 -


HLP-SP110 Series

Output frequency

C04.19 Max output


frequency

Reference

time
Start command

Speed up

Speed down

7.7 Parameter Initialization


1. Set C14.22 = 2;
2. Cut off the main power and Re-power on, LCP displays “E.80”;
3. Press “OFF” key on LCP;

7.8 Automatic Motor Adaption (AMA)


1. Reboot the drive;
2. Enter motor nameplate data to C01.20 to C01.25;
3. Choose option [2] in C01.29 to enable AMA;
4. LCP displays “PUSH”, “HAND”, press “HAND” key on LCP,
“-AT-” will be displayed;
5. Wait for the LCP displays “PUSH”, “ENT”, press “ ” key,
AMA complet.
Note: AMA doesn’t fit for rotate motor. Measurements are stored in
C01.30, C01.33, and C01.35

7.9 Simple PLC


7.9.1 Order Execution
Use order execution to achieve Eight-speed Internal Control Function.
For example, to achieve the function of 10Hz runs for 5s, -20Hz runs
for 10s, 25Hz runs for 12s, -50Hz runs for 15s, -10Hz runs for 7s, 12Hz
runs for 8s, 40Hz runs for 6s, 8Hz runs for 5s, the following figure is the
frequency curve:

- 162 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Output 40Hz
Frequency
25Hz

12Hz
10Hz 8Hz

Time

-20Hz
-50Hz

5s 10s 12s 15s 7s 8s 6s 5s

Parameters setting:

Parameter Value Function Parameter Value Function


Preset
C03.10[0] 20 C13.20[0] 5 Timer 0
reference 0
Preset
C03.10[1] -40 C13.20[1] 10 Timer 1
reference 1
Preset
C03.10[2] 50 C13.20[2] 12 Timer 2
reference 2
Preset
C03.10[3] -100 C13.20[3] 12 Timer 3
reference 3
Preset
C03.10[4] -20 C13.20[4] 15 Timer 4
reference 4
Preset
C03.10[5] 24 C13.20[5] 7 Timer 5
reference 5
Preset
C03.10[6] 80 C13.20[6] 6 Timer 6
reference 6
Preset
C03.10[7] 16 C13.20[7] 5 Timer 7
reference 7
Order
C13.00 1 C03.00 1 -max~+max
Execution
C13.51[0] C13.52[0] 29 Start timer 0
Start
39 Select preset
C13.51[1] Command C13.52[1] 10
ref. 0
C13.51[2] C13.52[2] 30 Start timer 1
Simple PLC
30 Select preset
C13.51[3] Time-out 0 C13.52[3] 11
ref. 1

HLP-SP110 Series Operating Manual - 163 -


HLP-SP110 Series

C13.51[4] C13.52[4] 31 Start timer 2


Simple PLC
31 Select preset
C13.51[5] Time-out 1 C13.52[5] 12
ref. 2
C13.51[6] C13.52[6] 65 Start timer 3
Simple PLC
32 Select preset
C13.51[7] Time-out 2 C13.52[7] 13
ref. 3
C13.51[8] Simple PLC C13.52[8] 66 Select Ramp 4
50
C13.51[9] Time-out 3 C13.52[9] 14 Start timer 4
Select preset
C13.51[10] Simple PLC C13.52[10] 67
51 ref. 4
Time-out 4
C13.51[11] C13.52[11] 15 Start timer 5
Select preset
C13.51[12] Simple PLC C13.52[12] 68
52 ref. 5
Time-out 5
C13.51[13] C13.52[13] 16 Start timer 6
Select preset
C13.51[14] Simple PLC C13.52[14] 69
53 ref. 6
Time-out 6
C13.51[15] C13.52[15] 17 Start timer 7
Simple PLC
C13.51[16] 54 C13.52[16] 1 No Action
Time-out 7
If C13.52[16] is set to [24] stop, the internal control eight-speed will
perform only one time, not cycles.

- 164 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Chapter 8 Faults and Solutions


8.1 Fault List
The drive has three different fault types: warning, alarm and error. When a
fault happens, the drive shows a specific code to indicate it.
When a warning happens, it means that the drive is close to its design limits for
some reason, but the drive still works. If the drive fault disappear, the warning
will also disappear. When a warning happens, LCP displays “A.XX” (XX is
warning code).
An alarm means that the drive has exceeded its design limits for some reason.
When this happens, the drive will trip. The driver must be reset in order to re-
run. When analarm happens, LCP displays “E.XX” (XX is alarm code).
When some alarms happen, the drive will lock itself. These alarms are called
trip-lock alarm. The Trip-lock alarm offers additional protection, the default
setting is that the main power should be cut off before resetting the alarm.
But by setting parameter C14.23 = 0, the trip-lock alarm can be reset without
cutting the main power off. But there is a risk of accident when choosing this
f unction. Before using this f unction, it is important to be familiar with the
drive and the whole system in order to be safe when dealing with the drive.
Error means the drive is in a state and unable to carry out an operation.W hen
anerror happens, LCP display “Er.XX” (XX is error code).

Fault
Warning Alarm Error Reason analysis
Description

Live Zero Please refer to C06.0 Live Zero


A.02 E.02
Error Timeout Time.

1. Motor cable connection prob-


lems;
A.03 E.03 Motor Loss
2. The drive power is greater than
the motor power;

Mains Phase 1. Missing phase on supply side;


A.04 E.04*
Loss 2. Too high voltage imbalance.

HLP-SP110 Series Operating Manual - 165 -


HLP-SP110 Series

Fault
Warning Alarm Error Reason analysis
Description

1. The input voltage is too high;


2. An external force drives the
motor during acceleration or
deceleration;
A.07 E.07 Over Voltage
3. The deceleration time is too
short;
4. The braking unit and braking
resistor are not installed.
1. Instantaneous power failure oc-
curs on the input power supply;
Under Volt- 2. The drive's input voltage is not
A.08 E.08
age within the allowable range;
3. The rectifier bridge and buffer
resistor are faulty.
1. The load is too heavy or locke-
drotor occurs on the motor;
Drive Over-
A.09 E.09 2. The drive model is of too small
load
power class;
3. C01.** is set improperly.

1. C01.24 is set improperly;


2. The load is too heavy or locke-
MotorOver- drotor occurs on the motor;
A.10 E.10
load 3. The drive model is of too small
power class;
4. C01.** is set improperly.

Thermistor damage,uncorrectly
Motor Over
E.11 installed or motor cooling equip-
Temperature
ment failure.

Torque exceeds the max. torque


A.12 E.12* Torque Limit
limit.

- 166 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Fault
Warning Alarm Error Reason analysis
Description

1. The acceleration time is too


short;
2. Manual torque boost or V/F
curve is not appropriate;
3. The input voltage is too low;
A.13 E.13* Over Current 4. The startup operation is per-
formed on the rotating motor;
5. A sudden load is added during
acceleration/deceleration;
6. The drive model is of too small
power class.

Discharge from output phases to


A.14 E.14* Earth fault
ground (22kW and below)

Short circuit in motor or on motor


E.16* Short Circuit
terminals.

Control Drive communication timeout,


A.17 E.17 Word Time- this alarm occurrs when C08.04
out is set to 1 or 5.

Too much dust on the fan or the


A.24 E.24 Fan Fault
fan is aging.

Brake resis- Brake resistor is short circuit,


E.25* tor short- leading the brake function in-
circuit valid.
Brake tran-
Brake transistor is short circuit
E.27 sisitor short-
leading brake function invalid.
circuit

Brake resistor is not connected or


E.28 Brake Detect
working.

Motor phase
E.30* Check the phase and motor.
U missing

HLP-SP110 Series Operating Manual - 167 -


HLP-SP110 Series

Fault
Warning Alarm Error Reason analysis
Description

Motor phase
E.31* Check the phase and motor.
V missing

Motor phase
E.32* Check the phase and motor.
W missing

Internal Contact the local distributor or


E.38*
Fault Holip Company.

Discharge from output phases to


E.44* Earth Fault
ground (22KW or more).

24V Power
E.47* 24V voltage power card failure
Card Fault

AMA check
Motor voltage and motor current
E.51 Unom and
error setting.
Inom

AMA Motor current is too low,check


E.52
Low Inom the settings.

AMA Motor Motor configuration is too large


E.53
is too large to perform AMA.

AMA Motor Motor configuration is too small ,


E.54
is too small unable to perform AMA.

AMA
Motor parameter is out of the
E.55 Paremeter
range
Error

AMA Inter- Interrupted by the user when run-


E.56
rupt ning AMA.

AMA
E.57 AMA takes too long to run.
Time-out

- 168 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Fault
Warning Alarm Error Reason analysis
Description

AMA Inter- Contact Local distributor or Holip


A.58 E.58
nal Error Company.

Current Current exceeds value set in


A.59
Limit C04.18.

Mechenical Actual motor current can not


E.63 Brake Cur- exceeds release brake current set
rent Low in C02.20 within start delay time.
1. The ambient temperature is too
high;
2. The air filter is blocked;
IGBT Over
A.69 E.69* 3. The fan is damaged;
Temperature
4. The thermally sensitive resistor
of the IGBT is damaged;
5. The drive IGBT is damaged.
Rectifier
Tempera- Rectifier Temperature Sensor
A.74 E.74
tureSensor Error
Error
1. The ambient temperature is too
Rectifier
high;
A.75 E.75 Tempera-
2. The air filter is blocked;
tureHigh
3. The fan is damaged.
IGBT Temper-
IGBT Temperature Sensor
A.76 E.76 ature Sensor
Error U
Error U
IGBT Temp
IGBT Temperature Sensor
A.77 E.77 erature Sen-
Error V
sor Error V
IGBT Tempe
IGBT Temperature Sensor
A.78 E.78 rature Sensor
Error W
Error W

Parameter
E.80 Make parameter initialized.
Initialization

HLP-SP110 Series Operating Manual - 169 -


HLP-SP110 Series

Fault
Warning Alarm Error Reason analysis
Description

1. The ambient temperature is too


Power Board
high;
E.83 Over Tem-
2. The air filter is blocked;
perature
3. The fan is damaged.

24V Power
E.88* 24V PowerCard Fault
Card Fault

LCP Con-
nection with No communication between LCP
Er.84
the drive and the drive.
failed

Button is
Er.85 Refer to parameter group C00.4*.
disabled

Parameter
Er.89 Try to write read-only parameter.
read-only

Parameter
value is in-
Er.91 Invalid parameter value to write.
valid in this
mode

Parameter is freezed or can’t be


Err Unchangbale
changed during running.

Note: Trip-lock alarm is with *.

- 170 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Chapter 9 Maintenance
9.1 Note
Confirm the main circuitpower supply has been turned off, and the
display has disappeared before carry out inspection and maintenance.
Make sure the system is in dynamic state, please pay attention to the
following:
• Check whether the power supply voltage matches to the rated
voltage of the drive;
• Check whether the motor makes unexpected noises or abnormal
vibration when running;
• Check whether there are abnormal heating;
• Check whether the drive output voltage,output current, output
f requency, and monitor display is g reater than the value
commonly used.
• Check whether the cooling fan installed at the lower part of the
drive runs normally;
• Check whether the ambient temperature is too high and whether
there is dust,iron filings, corrosive fluid in the drive;
• Check whether the ambient temperature of the drive is between
-10℃~40℃, and whether the humidity is between 5%-85% (95%
is without condensation), phenomenon of water droplets is not
allowed;
• The driveshould be discarded as industrial waste. It is forbidden
to burn it;

9.2 Storage and Transport


The drive must be kept in its original package box before installation.
Pay attention to the followings when keeping it in storage if the drive is
not used for the time being:
• It must be stored in a dry place without rubbish or dust;
• The suitable temperature for storage is between -25℃-65℃;
• The relative humidity required is 5%-95% without condensation;
• There is no corrosive gas or liquid in the storage ambience;
• It is better to lay the drive on a rack and keep it in a proper
package;
• The ambient temperature for transport is between -25℃-70℃;
• The relative humidity of transpor t ambience must be less
than95% (Ambient temperature is 40℃).
Attention: It is better not to store the drive for long time. Long time
storage of the drive will lead to the deterioration of electrolytic capacity.
If it needs to be stored for a long time make sure to power it up one time
within a year and the power-up time should be at least above five hours.
When powering up, supply voltage must be increased slowly with a
voltage regulator to the rated voltage value.

HLP-SP110 Series Operating Manual - 171 -


HLP-SP110 Series

Appendix A Modbus Communication


Specification
T he d r ive prov ide R S 485 c om mu n icat ion i nt e r fa ce. It a dopt s
international standard Modbus communication protocol to perform
master-slave communication. The user can realize centralized control
through PC/PLC to adapt specific application requirements.

1. Application Mode
1.1 Interface Mode

The communication interface is RS485. RS485 works on semiduplex and


its data signal applies differential transmission which is called balance
transmission too.

1.2 Networking Mode


The drive has two networking modes: single master/multiple slaves
networking and single master/single slave networking.

Single master/single slave networking diagram

Single master/multiple slaves networking diagram

Specification:
1. No m at t e r wh ich mo de, t he d r ive is u se d a s a slave i n
communication. When master sends commands using broadcast address,
the slave does not respond;
2. It is recommended to use shield cables in multiple connection.
The basic parameter of the devices, such as baud rate and digital check
bit in RS485 should be the same as slave device’s and there should be no
repeated addresses in slave devices.

- 172 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

2. Protocol Format
Modbus protocol supports both RTU and ASCII mode.

2.1 RTU Mode


RTU data frame format is shown as the figure below:

Specification:

Start at least 3.5 idle characters


Slave address Address: 0-247 (0 is broadcast address)
Function code Modbus function code
Data (N-1)
Data (N-2)
2 * N data

Data 0
CRC CHK high-8-bit
CRC check
CRC CHK low-8-bit
End at least 3.5 idle characters

2.2 ASCII Mode


ASCII data frame format is shown as the figure below:

Specification:
1. Frame header is "0x3A" while the default frame end is "0x0D"
"0x0A";
2. In ASCII mode, all data bytes other than frame header and end
are sent in the form of ASCII code; high-4-bit byte and low-4-bit byte are
sent successively;
3. In ASCII mode, the data is 7-bit long. For 'A'~'F', their uppercase
ASCII codes are used;
4. Data is subjected to LRC check which covers the information
portion from slave address to data;

HLP-SP110 Series Operating Manual - 173 -


HLP-SP110 Series

3. Function Code
Function code supported by the drive Modbus protocol are as shown in
the table below:

Function code Description Meaning


Read drive running status
0x01 Read Coil Status
parameters
Read drive functional
Read Holding
0x03 parameters and running status
Registers
parameters
Control whether the functional
0x05 Force Single Coil parameters are saved or not at
power loss.
Over-write individual drive
0x06 Preset Single Register
functional parameters
Control the drive running status
0x0F Force Multiple Coils
and set output frequency
Over-write multiple drive
0x10 Preset Multiple Regs
functional parameters

4. Register Address Definition


All the following register addresses are started from 0.

4.1 The Rules of Register Address of the Parameter Number


The parameters can be mapping to register address. The rules of register
address of the parameter number are shown below:
Register address = PNU × 10 – 1
For example:
The register address of C03.03 is 303 × 10 - 1 = 3029 (0x0BD5)
The register address of C16.13 is 1613 × 10 - 1 = 16129 (0x3F01)

4.2 Other Register Addresses Specification

In addition to parameter number is mapped to Modbus registers, there are


some additional registers within the drive which can be used to control
the drive, monitor the drive's status.

Register
Specification R/W
address
The internal error code of last
6 R
communication error

- 174 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Register address of last occurred


7 R
communication error
8* Parameter index R,W

2809* Control word R,W


2810* Reference R,W

2909 C16.03 Status word R


2910* Output frequency R
2911 C16.14 Output current R
2912 C16.30 DC link voltage R
2913 C16.12 Motor voltage R
2914 C16.13 Output frequency R
2915 C16.52 Feedback R

60800* Parameter which Par. No. is set in C39.00 R,W


60801* Parameter which Par. No. is set in C39.01 R,W

60835* Parameter which Par. No. is set in C39.35 R,W

* Reg 8 specification
Reg 8 is parameter index register. The drive has some array type
parameters. When accessing these parameters, it should be set index
first.
For example, write value into C03.10[2]. It should write 2 into Reg 8 first,
then write value into 3099 (the register address of C03.10 is 310 × 10-
1=3099, hexadecimal is 0x0C1B).

* Reg 2809 Control word specification

Bit 0 1
Bit0 Preset reference bit0 set to 0 Preset reference bit0 set to 1
Bit1 Preset reference bit1 set to 0 Preset reference bit1 set to 1
Bit2 DC brake No DC brake
Bit3 Coast stop No coast stop
Bit4 Quick stop No quick stop
Bit5 Freeze freq No freeze freq
Bit6 Ramp stop Run
Bit7 No reset Reset
Bit8 No jog Jog

HLP-SP110 Series Operating Manual - 175 -


HLP-SP110 Series

Bit9 Ramp 1 Ramp 2


Bit10 Data invalid Data valid
Bit11 Relay 2 off Relay 1 on
Bit12 Relay 2 off Relay 2 on
Bit13 Setup 1 Setup 2
Bit14 Reserved
Bit15 No reversing Reversing

* Reg 2810 referencespecification


The relationship between Reg 2810 reference and output frequency is
shown below:
Reg 2810 = output frequency ÷C03.03 ×16384
Multiplying 16384 is for high precision of calculation.
For example:
If you want to set output frequency to 20Hz, it should write 20÷50 ×
16384 = 6553.6 ≈ 6554 (0x199A) into Reg 2810.
If you want to set output frequency to -20Hz (running reverse 20Hz), it
should write -20÷50 × 16384 = -6553.6 ≈ -6554 (0xE666) into Reg 2810.

*Reg 2910output frequency specification


The data format of Reg 2910output frequency is differenct from C16.13.
Output frequency = Reg 2910 × C03.03 ÷ 16384
For example:
If reg 2910 = 0x2000 (8192), then the output frequency is 8192 ×50÷
16384 = 25Hz.
If reg 2910 = 0xE666 (-6554), then the output frequency is -6554 ×50÷
16384 =
-20Hz.

*Reg 60800~60835specification
C39.00~C39.35 is user-defined parameters.Users can set other parameter
number into C39.00 ~ C39.35, then users can read and write these
parameters quicky by communication.
Registers in Modbus is 16 bits. For using one message (eg. Write Multiple
Registers) to modify parameters which data type is UINT32/INT32 or
array, it need set index in C39.50~C39.85 which correspond to parameter
number in C39.00~C39.35.
For example:
Par.No. Value Par.No. Value Reg. Spec.
C39.00 303 C39.50 0 60800 C03.03 low 16 bits
C39.01 303 C39.51 1 60801 C03.03 high 16 bits
C39.02 310 C39.52 0 60802 C03.10[0]

- 176 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C39.03 310 C39.53 1 60803 C03.10[1]


C39.04 310 C39.54 2 60804 C03.10[2]
C39.05 1312 C39.55 0 60805 C13.12[0] low 16 bits
C39.06 1312 C39.56 100 60806 C13.12[0] high 16 bits
C39.07 1312 C39.57 1 60807 C13.12[1] low 16 bits
C39.08 1312 C39.58 101 60808 C13.12[1] high 16 bits
C39.09 1312 C39.59 2 60809 C13.12[2] low 16 bits
C39.10 1312 C39.60 102 60810 C13.12[2] high 16 bits

The data type of C03.03 is UINT32. Set C39.50 to 0 (index) to make Reg.
60800 corresponds to C03.03 low 16 bits, set C39.51 to 1 (index) to make
Reg. 60801 corresponds to C03.03 high 16 bits.
The data type of C03.10 is INT16, it is an array. Set C39.52~C39.54 to 0, 1,
2 respectively to make Reg. 60802~60804 correspond to C03.10[0]~[2].
The data type of C13.12 is INT32, it is an array. For this data type,
hundreds digit represents high or low 16 bits, tens digit and ones digit
represent array index. So set C39.10=1312, C39.60=102 makes Reg.
60810 corresponds to C13.12[2] high 16 bits

4.3 Parameter’s Data Type


Parameters have different data type decause of they have different range
and value. Parameter’s data type is shown in the following table.
Par. No. Data Type Par. No. Data Type
C00.03~C00.12 UINT8 C08.01~C08.02 UINT8
C00.31~C00.32 INT32 C08.03 UINT16
C00.33 UINT16 C08.04~C08.33 UINT8
C00.40~C00.60 UINT8 C08.35~C08.36 UINT16
C00.62~C00.64 INT32 C08.38~C08.56 UINT8
C01.00~C01.20 UINT8 C13.00~C13.11 UINT8
C01.22~C01.23 UINT16 C13.12 INT32
C01.24 UINT32 C13.20 UINT32
C01.25 UINT16 C13.40~C13.52 UINT8
C01.29 UINT8 C14.01~C14.10 UINT8
C01.30~C01.35 UINT32 C14.11 UINT16
C01.39~C01.42 UINT8 C14.12~C14.17 UINT8
C01.50~C01.65 UINT16 C14.18 UINT16
C01.71~ C01.73 UINT8 C14.20 UINT8
C01.75~ C01.76 UINT16 C14.21 UINT16
C01.80 UINT8 C14.22~C14.27 UINT8
C01.82 UINT16 C14.30~C14.34 UINT16

HLP-SP110 Series Operating Manual - 177 -


HLP-SP110 Series

C01.90~ C01.93 UINT8 C14.40~C14.63 UINT8


C02.00~ C02.04 UINT16 C15.00~C15.03 UINT32
C02.08~ C02.10 UINT8 C15.04~C15.05 UINT16
C02.11~ C02.16 UINT16 C15.06~C15.30 UINT8
C02.17 UINT8 C15.31 INT16
C02.18~ C02.19 UINT16 C15.38 UINT8
C02.20 UINT32 C15.43 STRING
C02.22 UINT16 C16.00 UINT16
C03.00 UINT8 C16.01 INT32
C03.03 INT32 C16.02 INT16
C03.07 UINT8 C16.03 UINT16
C03.10 INT16 C16.04 UINT8
C03.11 UINT16 C16.05 UINT16
C03.12 INT16 C16.09 INT32
C03.13 UINT16 C16.10~C16.13 UINT32
C03.14 INT16 C16.14~C16.15 UINT16
C03.15~C03.40 UINT8 C16.16 INT32
C03.41~C03.42 UINT32 C16.18 UINT8
C03.50 UINT8 C16.30 UINT32
C03.51~C03.52 UINT32 C16.34 INT8
C03.60 UINT8 C16.35 UINT8
C03.61~C03.62 UINT32 C16.36~C16.37 UINT32
C03.70 UINT8 C16.38 UINT8
C03.71~C03.72 UINT32 C16.40 UINT16
C03.80 UINT32 C16.48~C16.49 INT8
C04.10 UINT8 C16.50~C16.51 INT16
C04.12~C04.19 UINT16 C16.52 INT32
C04.21~C04.42 UINT8 C16.60 UINT16
C04.50~C04.51 UINT32 C16.61 UINT8
C04.52~C04.53 UINT16 C16.62 UINT16
C04.54~C04.57 INT32 C16.63 UINT8
C04.58 UINT8 C16.64~C16.65 UINT16
C04.61~C04.63 UINT16 C16.66 UINT8
C05.04~C05.40 UINT8 C16.68~C16.69 UINT32
C05.55~C05.56 UINT32 C16.71 UINT16
C05.57~C05.58 INT32 C16.72~C16.73 INT32
C05.59 UINT16 C16.78 UINT16
C05.60 UINT8 C16.86 INT16

- 178 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

C05.61~C05.62 UINT32 C16.90~C16.93 UINT32


C05.63~C05.64 UINT16 C30.00 UINT8
C06.00~C06.01 UINT8 C30.01 UINT32
C06.10~C06.13 UINT16 C30.02~C30.10 UINT16
C06.14~C06.15 INT32 C30.11 UINT32
C06.16~C06.18 UINT16 C30.12~C30.15 UINT8
C06.19 UINT8 C30.16 UINT16
C06.20~C06.23 UINT16 C30.17 UINT8
C06.24~C06.25 INT32 C30.18 UINT16
C06.26~C06.28 UINT16 C30.20 UINT8
C06.29 UINT8 C30.21 INT8
C06.70~C06.71 UINT8 C30.22 INT8
C06.73~C06.74 UINT16 C30.30 UINT8
C06.81~C06.82 INT32 C30.31 UINT16
C06.90~C06.91 UINT8 C30.32 UINT16
C06.93~C06.94 UINT16 C30.33~C30.39 UINT8
C07.12~C07.13 UINT16
C07.20~C07.31 UINT8
C07.32~C07.33 UINT16
C07.34 UINT32
C07.35~C07.39 UINT16
C07.41~C07.42 INT16
C07.45~C07.46 UINT8
C07.50~C07.51 INT16
C07.55 UINT8

UINT8 represents Unsigned Integer 8 bits;


UINT16 represents Unsigned Integer 16 bits;
UINT32 represents Unsigned Integer 32 bits;
INT8 represents Integer 8 bits;
INT16 represents Integer 16 bits;
INT32 represents Integer 32 bits;
STRING represents text string;

HLP-SP110 Series Operating Manual - 179 -


HLP-SP110 Series

5. Coils address definition


All the following coils addresses are started from 0.

Coils address 0 1 R/W


Preset reference bit0 set to Preset reference bit0 set
0 R,W
0 to 1
Preset reference bit1 set to Preset reference bit1 set
1 R,W
0 to 1
2 DC brake NoDC brake R,W
3 Coast stop No coast stop R,W
4 Reserved R,W
5 Freeze f req Freeze f req R,W
6 Ramp stop Ramp stop R,W
7 No reset Reset R,W
8 No jog Jog R,W
9 Ramp 1 Ramp 2 R,W
10 Data invalid Data valid R,W
11 Relay 1 off Relay1on R,W
12 Relay2 off Relay2 on R,W
13 Setup1 Setup 2 R,W
14 Reserved
15 No reversing Reversing R,W
16~31 Reference R,W
32 Control not ready Control ready R
33 Drive not ready Drive ready R
34 Coasting stop Satety closed R
35 No alarm Alarm R
36 No warning Warning R
37 Reserved R
38 No trip-lock Trip-lock R
39 No warning Warning R
40 Not at reference At reference R
41 Hand mode Auto mode R
42 Out of f req range In f req range R
43 Stopped Running R
No resistor braking war-
44 Resistor braking waring R
ing
45 No voltage warning Voltage warning R

- 180 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

46 Not in current limit Current limit R


47 No thermal warning Thermal warning R
48~63 Output f requency R
Whether the f unctional parameters are saved or not
64 W
at power loss.

6. Communication ratio values


The Communication data is expressed by hexadecimal in actual
application and there is no radix point in hexadecimal. For example,
Ifyou want to set C03.10[0] = 60.34, 60.34 can be magnified by 100 times
into 6034. So hex 0x1792 (6034) can be used to express 60.34.
A non-integer can be timed by a multiple to get an integer and the integer
can be called communication ratio values.
The communication ratio values are refered to the radix point of the
setting range of default value in the functional parameter list. If there are
radix point n, then the communication ratio value m is 10^n.

7. Error message
There may be errors in the communication process, for example, some
parameters are read-only, but the PC/PLC sends a written directive, the
drive will return an error message.
Error message data frame format is shown as the figure below:

Error message function code = requirements function code + 0x80

Error code Specification


Function code error, the drive does not support this kind
0x01
of function code.
0x02 Defined parameters can not be written.
0x03 The value exceeds the upper limit of the parameter
0x04 Operation error.

HLP-SP110 Series Operating Manual - 181 -


HLP-SP110 Series

8. Examples
8.1 Read Holding Registers (0x03)
8.1.1 Read Output Frequency
Read the value of C16.13 to get the output frequency.
Transmit: 01 03 3F 01 00 02 99 DF (Hexadecimal)
Receive: 01 03 04 00 00 01 F4 FA 24 (Hexadecimal)
Transmit data specification:

Field Description
01 Address
03 Function
Register address (ADDRH ADDRL). The register address of
3F 01
C16.13 is 1613*10-1=16129 (0x3F01)
00 02 The number of read registers is 2
99 DF CRC check

Receive data specification:

Field Description
01 Address
03 Function
04 The byte number of received data
00 00 01 0x000001F4 converts to decimal number is 500. So the value
F4 of C16.13 is 500*0.01 = 50.0
FA 24 CRC check

Note: The data type of C16.13 is UINT32, so it needs read 2 registers.

8.1.2 Read Drive Status


Read the value of C16.03 or register 2909 to get the drive status.
Transmit: 01 03 3E 9D 00 01 18 0C (Hexadecimal)
Receive: 01 03 02 02 58 B8 DE (Hexadecimal)
Transmit data specification:

Field Description
01 Address
03 Function
Register address (ADDRH ADDRL). The register address of
3E 9D
C16.03 is 1603*10-1=16029 (0x3E9D)
00 01 The number of read registers is 1
18 0C CRC check

- 182 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Receive data specification:

Field Description
01 Address
03 Function
02 The byte number of received data
Status word: 0x0258
02 58 0x0258 converts to binary number is 0000 0010 0101 1000. They
correspond to parameter C16.03 bit 0~15.
B8 DE CRC check

8.2 Write Single Register (0x06)


8.2.1 Set Drive Output Frequency

Write C03.10[0] to set the drive output frequency.


For example: If you want to set the drive output frequency to 20.0Hz,
to set C03.10[0] to 40.00% (default: C03.03=50.000, 20.0 = 50.000 ×
40.00%).
Transmit: 01 06 0C 1B 0F A0 FF 15 (Hexadecimal)
Receive: 01 06 0C 1B 0F A0 FF 15 (Hexadecimal)
Transmit data specification:

Field Description
01 Address
06 Function
Register address (ADDRH ADDRL). The register address of
0C 1B
C03.10 is 310 *10-1=3099 (0x0C1B)
The value which will be written into C03.10[0] is 40.00%
0F A0
(Decimal: 4000, Hexadecimal: 0x0FA0).
FF 15 CRC check

Receive data specification:

Field Description
01 Address
06 Function
Register address (ADDRH ADDRL). The register address
0C 1B
of C03.10 is 310 *10-1=3099 (0x0C1B)
The value which has be written into C03.10[0] is 40.00%
0F A0
(Decimal: 4000, Hexadecimal: 0x0FA0).
FF 15 CRC check

HLP-SP110 Series Operating Manual - 183 -


HLP-SP110 Series

8.2.2 Start/Stop Drive


Write register 2809 to control the drive running.
For example: Start drive
Transmit: 01 06 0A F9 04 7C 59 02 (Hexadecimal)
Receive: 01 06 0A F9 04 7C 59 02 (Hexadecimal)
Transmit data specification:

Field Description
01 Address
06 Function
0A F9 Register address 2809 (0x0AF9)
The value which will be written into Reg. 2809 is 0x047C
(Control word)
04 7C
0x047C converts to binary number is: 0000 0100 0111 1100,
They correspond to Reg. 2809 bit 0~15.
59 02 CRC check

Receive data specification:

Field Description
01 Address
06 Function
0A F9 Register address 2809 (0x0AF9)
The value which has be written into Reg. 2809 is 0x047C
04 7C
(Control word)
59 02 CRC check

8.3 Write Multiple Registers (0x10)


8.3.1 Start/Stop Drive and Set Drive Output Frequency

Write register 2809 to control the drive running and write register 2810
to set the drive output frequency.
Transmit: 01 10 0A F9 00 02 04 04 7C 19 9A 09 32 (Hexadecimal)
Receive: 01 10 0A F9 00 02 92 21 (Hexadecimal)
Transmit data specification:

Field Description
01 Address
10 Function
0A F9 Register address 2809 (0x0AF9)
00 02 The number of write registers is 2
04 The byte number of write data is 4

- 184 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

Reg. 2809 = 0x047C (Control word)


04 7C 19 Reg. 2810 = 0x199A (If you want to set output frequency
9A to 20Hz, it should write 20 ÷ 50 × 16384 = 6553.6 ≈ 6554
(0x199A) into Reg. 2810) .
09 32 CRC check

Receive data specification:

Field Description
01 Address
10 Function
0A F9 Register address 2809 (0x0AF9)
00 02 The number of write registers is 2
92 21 CRC check

Attention: The maximum register number can be written in one message


is 10.

8.4 Read Coils (0x01)


8.4.1 Read Output Frequency

The coil’s address 48~63 represents drive output frequency.


Transmit: 01 01 00 30 00 10 3D C9 (Hexadecimal)
Receive: 01 01 02 00 20 B8 24 (Hexadecimal)
Transmit data specification:

Field Description
01 Address
01 Function
Coil address (ADDRH ADDRL), 0x0030 converts to decimal
00 30
number is 48.
Data bits number is 16 (48~63), 0x0010 converts to decimal
00 10
number is 16.
3C 0C CRC check

Receive data specification:

Field Description
01 Address
01 Function
02 The number of read byte is 2

HLP-SP110 Series Operating Manual - 185 -


HLP-SP110 Series

Ouput frequency. Swap high and low, the data is 0x2000,


so the output frequency is 50% of C03.03. Why does
00 20
0x2000 correspond to 50%, please refer to Reg. 2910 output
frequency specification.
B8 24 CRC check

8.4.2 Read Drive Status


The coil’s address 32~47 represents drive status.
Transmit: 01 01 00 20 00 10 3C 0C (Hexadecimal)
Receive: 01 01 02 02 58 B9 66 (Hexadecimal)
Transmit data specification:

Field Description
01 Address
01 Function
Coil address (ADDRH ADDRL), 0x0030 converts to
00 20
decimal number is 32.
Data bits number is 16 (32~47), 0x0010 converts to decimal
00 10
number is 16.
3C 0C CRC check

Receive data specification:

Field Description
01 Address
01 Function
02 The number of read byte is 2
Status word: 0x0258.
02 58 0x0258 converts to binary number is 0000 0010 0101 1000,
they correspond to coils 32~47.
B9 66 CRC check

8.5 Write Single Coil (0x05)

Write coil 64 to control parameter saved to RAM or EEPROM at power


down.
Transmit: 01 05 00 40 FF 00 8D EE (Hexadecimal)
Receive: 01 05 00 40 FF 00 8D EE (Hexadecimal)
Transmit data specification:
Field Description
01 Address

- 186 - HLP-SP110 Series Operating Manual


HLP-SP110 Series

05 Function
Coil address (ADDRH ADDRL), 0x0040 converts to
00 40 decimal number is 64, it means parameter save control at
power down.
FF 00 means saved to EEPROM at power down
FF 00
00 00 means saved to RAM at power down
8D EE CRC check

Receive data specification:

Field Description
01 Address
05 Function
Coil address (ADDRH ADDRL), 0x0040 converts to
00 40 decimal number is 64, it means parameter save control at
power down.
FF 00 means saved to EEPROM at power down
FF 00
00 00 means saved to RAM at power down
8D EE CRC check

8.6 Write Multiple Coils (0x0F)

Start/stop drive and set drive output frequency.


Transmit: 01 0F 00 00 00 20 04 7C 04 9A 19 37 B3 (Hexadecimal)
Receive: 01 0F 00 00 00 20 54 13 (Hexadecimal)
Transmit data specification:

Field Description
01 Address
0F Function
Coil address (ADDRH ADDRL), 0x0000 converts to
00 00
decimal number is 0.
Data bits number is 32 (0~31), 0~15 represents control word,
00 20
16~31 represents reference.
04 The number of write byte is 4.
7C 04 Control word , swap high and low, the data is 0x047C.
Reference, If you want to set output frequency to 20Hz, it
9A 19
should write 20 ÷ 50 × 16384 = 6553.6 ≈ 6554 (0x199A).
37 B3 CRC check

HLP-SP110 Series Operating Manual - 187 -


HLP-SP110 Series

Receive data specification:

Field Description
01 Address
0F Function
Coil address (ADDRH ADDRL), 0x0000 converts to
00 00
decimal number is 0.
00 20 The number of write bits is 0x0020 (32 bits), that’s 4 bytes.
54 13 CRC check

- 188 - HLP-SP110 Series Operating Manual


1 2 3 4
HLP-SP110 Series

Appendix B Copy Card Specification
Copy Card can copy parameters from one drive to another.

1. Copy Card Interface

2. Installation

Use netcable to connect the copy card and the drive. Plug one terminal
1 into
2 the copy card
3 RJ45 port
4 which is 5placed on the
6 back and plug
7 the 8

other terminal into drive RJ45 port. As shown in the following figure: 1 2 3 4


A A

B B


Projection Scale Size Material


C C

1:1  A4 Danfoss Standard

Designation

Mrk. Approval/Rev Date D


copy-card.drw D

Replace

Design

F Approval
E E

Confidential:  Property of Danfoss A/S, Nordborg, Denmark.
Not to be handed over to, copied or used by third party. Two- or three
Projection Scale

1:1 
No. COPY-CARD 
Size

A4
Material

Danfoss Standard

dimensional reproduction of contents to be authorized by Danfoss A/S.
Mrk. Approval/Rev Date
Rev. Designation

copy-card.drw D
Sheet 

1 2 Replace

Design 3 F

F Approval

Confidential:  Property of Danfoss A/S, Nordborg, Denmark.
Not to be handed over to, copied or used by third party. Two- or three
No. COPY-CARD 
dimensional reproduction of contents to be authorized by Danfoss A/S. Rev. Sheet  1/1 

1 2 3 4


1:2
Projection Scale Size Material

7:50  A3 Danfoss Standard

Designation

Mrk. Approval/Rev Date a3-exploded.drw


Replace

Design

HLP-SP110 Series Operating Manual Approval

Confidential:  Property of Danfoss A/S, Nordborg, Denmark.
Not to be handed over to, copied or used by third party. Two- or three
- 189 -
No. A3-EXPLODED 

dimensional reproduction of contents to be authorized by Danfoss A/S. Rev. Sheet  1/1 

1 2 3 4 5 6 7 8
HLP-SP110 Series

3. Operation
3.1 Upload

1) Connect copy card and drive according to 2. Installation;


2) After the drive power on, Power indicator on the copy card will be
ON. If the connection between copy card and drive is not OK, Fail
indicator will be ON;
3) Press Upload key, parameters in drive begin copying to copy card.
Trans indicator will be blinking during transfer.
4) If an error occurs during transfer, Fail indicator will be ON; If data
upload success, Trans indicator will be OFF;

3.2 Download
1) Connect copy card and drive according to 2. Installation;
2) After the drive power on, Power indicator on the copy card will be
ON. If the connection between copy card and drive is not OK, Fail
indicator will be ON;
3) Press Download key, parameters in copy card begin copying to drive.
Trans indicator will be blinking during transfer.
4) If an error occurs during transfer, Fail indicator will be ON; If data
download success, Trans indicator will be OFF;

3.3 Part Download

Part download is similar to download, use Part key instead of Download


key. It copies parameters from copy card to drive except motor data.

- 190 - HLP-SP110 Series Operating Manual

You might also like