Electricity: by Mr. A
Electricity: by Mr. A
Electricity: by Mr. A
6. Name the physical quantity which is (i) same (ii) different in all the bulbs when three bulbs of:
(a) same wattage are connected in series.
(b) same wattage are connected in parallel.
(c) different wattage are connected in series.
(d) different wattage are connected in parallel.
Answer. (a) For identical bulbs in series- same current, same potential difference.
(b) For identical bulbs in parallel- same potential difference, different current.
(c) For unidentical bulbs in series- same current, different potential difference.
(d) For unidentical bulbs in parallel- different current, same potential difference.
7. A given length of a wire is doubled on itself and this process is repeated once again. By what
factor does the resistance of the wire change?
Answer. Am. Length becomes one-fourth of the original length and area of cross-section
becomes four times that of original.
So, new resistance is (1/16)th of original resistance.
(a) When 1 A current flows across the wire in 1 second, the charge transfer across its ends is said
to be 1 coulomb.
(b) The relationship between the electric current I, the charge q and time t is
12. (a) How is the direction of electric current related to the direction of flow of electrons in a
wire?
(b) Calculate the current in a circuit if 500 C of charge passes through it in 10 minutes.
Answer.
(a) Conventional direction of electric current is opposite to the direction of flow of electrons in a wire.
(b) q = 500 C, t = 10 X 60 = 600 s
I = 500/600 = 5/6A
13. An electric iron has a rating of 750 W, 220 V. Calculate the (i) current flowing through it,
and (ii) its resistance when in use.
Answer. Given: P = 750 W, V = 220 V
(i) P = VI
14. Study the following electric circuit and find (i) the current flowing in the circuit and (ii) the
potential difference across 10 Ω resistor.
Answer.
15. What is meant by electric current? Name and define its SI unit. In a conductor electrons are
flowing from B to A. What is the direction of conventional current? Give justification for
your answer. A steady current of 1 ampere flows through a conductor. Calculate the
number of electrons that flows through any section of the conductor in 1 second. (Charge on
electron 1.6 X 10-19 coulomb).
Answer.
Electric Current: The amount of charge ‘Q’ flowing through a particular area of cross section
in unit time ‘t’ is called electric current, i.e.
A Electric current, I = Q/t
By Mr. Page 2
SI unit of electric current is ampere.
One ampere of current is that current which flow when one coulomb of electric charge
flowing through a particular area of cross-section of the conductor in one second, i.e. 1A = 1
Cs-1.
The direction of conventional current is A to B, i.e. opposite to the direction of flow of
electrons. In a metal, flow of electrons carrying negative charge constitutes the current.
Direction of flow of electrons gives the direction of electronic current by convention, the
direction of flow of positive charge is taken as the direction of conventional current.
Charge = q = ne
16. What is meant by electrical resistivity of a material? Derive its S.I. unit.
Answer. Mathematically, resistivity of the conducting material is given by
= R A/l
If l = 1 m, A = 1 m2, then = R
Hence, the resistivity of the material is defined as the resistance offered by a metallic wire having
a unit length and a unit area of cross-section. Since unit length and unit area of cross-section
forms a cube, the specific resistance or resistivity can also be defined as the resistance offered by
a cube of a material of side 1 m when current flows perpendicularly through the opposite faces. In
SI system, its units is
17. (a) Write two points of difference between electric energy and electric power. (6) Out of 60
W and 40 W lamps, which one has higher electrical resistance when in use.
(c) What is the commercial unit of electric energy? Convert it into joules.
Answer. (a) Difference between electric energy and electric power:
By Mr. A Page 3
Aim: Same current flows through every part of the above circuit.
Procedure:
Connect ammeters, ‘A’1 between B and C, and ‘A2’ between D and E.
Adjust the sliding contact of the rheostat initially for a small current.
Note all the ammeter readings. These reading give us current flowing through the resistors R1, R2
and R3
The current in the circuit is now increased by changing the position of sliding contact J’ of the
rheostat.
Note all the ammeter readings each time.
Conclusion: Same reading of all the ammeter in each observation concluded that same current
flows through every part of the circuit.
Precautions:
All the connection should be tight and properly connected as per circuit diagram.
The positive terminal of the ammeter and voltmeter must be connected to the positive terminal of
the battery or battery eliminator.
19. State Ohm’s law. Write the necessary conditions for its validity. How is this law verified
experimentally? What will be the nature of graph between potential difference and current
for a conductor? Name the physical quantity that can be obtained from this graph.
Answer. Ohm’s law : When the physical conditions such as temperature etc. remain same, the
current flowing through the conductor is directly proportional to the potential difference applied
across the ends of the conductor, i.e.,
Necessary condition for validity of Ohm’s law is that physical condition such as
temperature of the conductor remains same.
Procedure:
Experiment to verify ohm's law
Procedure : 1. Connect the various components as.
2. Close the sky, so that current begins to flow in the circuit.
3. Note down the potential difference (V) across the conductor
PQ of resistance R shown by the voltmeter and the corresponding
current (I) shown by the ammeter.
4. Now move the knob of rheostat so that the current in the circuit
increases.
5. Again note down the potential difference (V) across the conductor R in the voltmeter and
current in the circuit shown by ammeter.
6. Repeat the experiment five times by increasing the current in the circuit by moving the knob of
the rheostat in steps.
S. No. Potential Difference (V) Current (I) V/ I
1
2
3
4
By Mr. A Page 4
Conclusion : From the graph between V and I, we conclude that I = V, which is Ohm's law.
Hence Ohm's law is verified experimentally.
Ohm's law does not hold under all conditions. Ohm's law does not hold for non-ohmic material
such as electrotyte.
20. (a) Define electric power. Express it in terms of potential difference V and resistance R.
(b) An electrical fuse is rated at 2 A. What is meant by this statement?
(c) An electric iron of 1 kW is operated at 220 V. Find which of the following fuses that
respectively rated at 1 A,3 A and 5 A can be used in it.
Answer.
(a) Electric power: It is the rate of doing work by an energy source or the rate at which the
electrical energy is dissipated or consumed per unit time in the electric circuit is called electric
power.
(b) It means, the maximum current will flow through it is only 2 A. Fuse wire will melt if the
current exceeds 2 A value through it.
21. Write relation between heat energy produced in a conductor when a potential difference V
is applied across its terminals and a current I flows through for ‘t’
Answer. Heat produced, H = VIt
22. State difference between the wire used in the element of an electric heater and in a fuse
wire.
Answer. The wire used in the element of electric heater has a high resistivity and have a high
melting point, i.e. even at a high temperature element do not burn while fuse wire have a low
melting point and high resistivity.
23. Find the current flowing through the following electric circuit.
Answer.
24. An electric bulb of resistance 200Ω draws a current of 1 Ampere. Calculate the power of the
bulb the potential difference at its ends and the energy in kWh consumed burning it for 5h.
Answer. Power of the bulb,
By Mr. A Page 5
25. Draw a schematic diagrams of an electric circuit comprising of 3 cells and an electric bulb,
ammeter, plug-key in the ON mode and another with same components but with two bulbs
in parallel and a voltmeter across the combination.
Answer.
26. Explain the role of fuse in series with any electrical appliance in an electric circuit. Why
should a fuse with defined rating for an electric circuit not be replaced by one with a larger
rating?
Answer. Fuse wire is a safety device connected in series with the live wire of circuit. It has high
resistivity and low melting point. It melts when a sudden urge of large current passes through it
and disconnects the entire circuit from the electrical supply. But, in case if we use a larger rating
instead of a defined rating, then it will not protect the circuit as high current will easily pass
through it and it will not melt.
27. An electric bulb is rated at 60 W, 240 V. Calculate its resistance. If the voltage drops to 192
V, calculate the power consumed and the current drawn by the bulb. (Assume that the
resistance of the bulb remain unchanged.)
Answer: 38.4 W and 0.2 A
28. The charge possessed by an electron is 1.6 X 10-19 coulombs. Find the number of electrons
that will flow per second to constitute a current of 1 ampere.
Answer: 6.25 x 10^18 electrons
29. Two devices of rating 44 W, 220 V and 11 W, 220 V are connected in series. The
combination is connected across a 440 V mains. The fuse of which of the two devices is likely
to burn when the switch is ON? Justify your answer.
Answer.
30. Consider the circuit shown in the diagram. Find the current in 3Ω resistor.
Answer. 3 Ω and 6 Ω are in parallel.
By Mr. A Page 6
31. Series arrangements are not used for domestic circuits. List any three reasons.
Answer. Series arrangements are not used for domestic circuit because
The electrical appliances need current of widely different values to operate properly.
In series arrangement, when one component fails, the circuit is broken and none of the
components works.
All electrical appliances work at a constant voltage. But in series circuit, the current is constant
throughout the electric circuit and potential is different across the different components. So, series
arrangement is not suitable for domestic circuits.
32. Explain with the help of a labelled circuit diagram, how will you find the resistance of a
combination of three resistors, of resistance R1, R2 and R3 joined in parallel. Also mention
how will you connect the ammeter and the voltmeter in the circuit while measuring the
current in the circuit and the potential difference across one of the three resistors of the
combination.
Answer. Parallel Combination:
Connect the three given resistor R1, R2 and R?i in parallel between the point XY with a battery, a
plug key and ammeter in series as shown in figure.
Connect voltmeter in parallel with these resistors between the terminals X and Y.
Close the key and note the ammeter and voltmeter reading. Ammeter shows the total current
drawn by the parallel combination of these resistors while voltmeter shows the voltage applied
across the combination.
Using Ohm’s law, find the equivalent resistance of the combination, i.e. equivalent resistance,
To find the current flow through any one of the resistor, ammeter will be connected in series with
that resistor and to measure the potential difference across that resistor, voltmeter must be
connected in parallel with that resistor as shown.
33.Deduce the expression for the equivalent resistance of the
parallel combination of three resistors R1, R2 and R3
Consider the following electric circuit:
(a) Which two resistors are connected in series?
(b) Which two resistors are connected in parallel?
(c) If every resistor of the circuit is of 2 Ω, what current will flow in the circuit?
Answer. Consider the following parallel circuit shown below: Let I1, I2 and I3 be the current flow
through the resistor R1, R2 and R3 connected in parallel.
Using Ohm’s law, current through each resistor is
Let W be the work done in carrying the charge q across the conductor, then
36. A piece of wire of resistance 20 Ω is drawn out so that its length is increased to twice its
original length. Calculate the resistance of the wire in the new Situation.
Answer: 80 ohm
37. (a) Two resistors R1and R2 may form (i) a series combination or (ii) a parallel
combination, and the combination may be connected to a battery of 6 volts. In which
combination, will the potential difference acrossR1 and across R2 be the same and in which
combination, will the current through R1 and through R2 be the same?
(b) For the circuit shown in this diagram, calculate
(i) the resultant resistance.
(ii) the total current.
(iii) the voltage across 7 Ω resistor.
Answer. (a) Potential difference across R1 and R2 is same in parallel combination of R1 and R2
and the current through R1 and R2 will be same when they are connected in series.
By Mr. A Page 8