Product Information

Customer : DATE : 16 Mar. 2010

SAMSUNG
SAMSUNG TFT-LCD
TFT-LCD

MODEL
MODEL :: LTY320HM01
LTY320HM01
The information Described in this Specification is Preliminary and can be charged
without prior notice

NOTE :

SL Development Team, LCD Business

Samsung Electronics Co . , LTD.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 1 / 29

From 【液晶之家】— www.fpdclub.net

 Contents

Revision History -------------------------------------------------------------------------------------------- (3)

General Description --------------------------------------------------------------------------------------- (4)
General Information --------------------------------------------------------------------------------------- (4)
1. Absolute Maximum Ratings -------------------------------------------------------------------------- (5)
2. Optical Characteristics --------------------------------------------------------------------------------- (6)
3. Electrical Characteristics ------------------------------------------------------------------------------- (9)
3.1 TFT LCD Module
3.2 Back Light Unit
4. Block Diagram ------------------------------------------------------------------------------------------- (11)
5. Input Terminal Pin Assignment --------------------------------------------------------------------- (12)
5.1 Input Signal & Power
5.2 Inverter Input Pin Configuration
5.3 Inverter Input Power Sequence & Specification
5.4 LVDS Interface
5.5 Input Signals, Basic Display Colors and Gray Scale of Each Color
6. Interface Timing ---------------------------------------------------------------------------------------- (19)
7.1 Timing Parameters (DE only mode)
7.2 Timing Diagrams of interface Signal (DE only mode)
7.3 Power ON/OFF Sequence
7. Outline Dimension -------------------------------------------------------------------------------------- (22)
8. Packing ------------------------------------------------------------------------------------------------- (24)
9. Marking & Others ------------------------------------------------------------------------------------- (26)
10. General Precaution ---------------------------------------------------------------------------------- (27)
10.1 Handling
10.2 Storage
10.3 Operation
10.4 Operation Condition Guide
10.5 Others

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 2 / 29

From 【液晶之家】— www.fpdclub.net

* Revision History

Rev.
Date Page Summary
No

Mar.
16, 000 - First Issued
2010

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 3 / 29

From 【液晶之家】— www.fpdclub.net

General Description
Description
LTY320HM01 is a color active matrix liquid crystal display (LCD) that uses amorphous
silicon TFT(Thin Film Transistor) as switching components. This model is composed of a
TFT LCD panel, a driver circuit and a back light unit. The resolution of a 32.0“ is 1920 x
1080 and this model can display up to 16.7million colors with wide viewing angle of 89° or
higher in all directions. This panel is intended to support applications to provide a excellent
performance for Flat Panel Display such as Home-alone Multimedia TFT-LCD TV, Display
terminals for AV application products, and High Definition TV (HDTV).

Features
 RoHS compliance (Pb-free)
 High contrast ratio, high aperture ratio, fast response time
 SPVA (Super Patterned Vertical Align) mode
 Wide viewing angle (±89°)
 Full HD (1920 x 1080 pixels) resolution (16:9)
 Low Power consumption
 4 CCFTs (Cold Cathode Fluorescent Tube)
 LVDS (Low Voltage Differential Signaling) interface

General Information

Items Specification Unit Note

960(HTYP) x 450(VTYP) ±1.0mm
Module Size mm
57.2(DMAX)
Weight 6000(Max) g
Pixel Pitch 0.12125(H) * 3 x 0.36375(V) mm
Active Display Area 698.4(H) x 392.85(V) mm
Surface Treatment Haze 7%, Hard-coating (3H)

Display Colors 8 bit- 16.7M colors

Number of Pixels 1920 x 1080 pixel

Pixel Arrangement RGB vertical stripe

Display Mode Normally Black

Luminance of White 450 cd/m2 Typ.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 4 / 29

From 【液晶之家】— www.fpdclub.net

1. Absolute Maximum Ratings
If the condition exceeds maximum ratings, it can cause malfunction or unrecoverable
damage to the device.

Item Symbol Min. Max. Unit Note

Power Supply Voltage VDD GND-0.5 13 V (1)

Storage temperature TSTG -20 65 ℃ (2)

Operating Temperature TOPR 0 50 ℃ (2)
Panel surface temperature TSUR 0 65 ℃ (3)
Shock ( non - operating ) SNOP - 50 G (4)
Vibration ( non - operating ) VNOP - 1.5 G (5)
Note (1) Ta= 25 ± 2 °C
(2) Temperature and relative humidity range are shown in the figure below.
a. 93.8 % RH Max. (Ta ≤ 40 °C)
b. Maximum wet-bulb temperature at 40 °C or less. (Ta ≤ 40 °C)
c. No condensation
(3) Polarizer will not be damaged in this range, even though abnormal visual problems occur
in TSUR range.
(4) 11ms, sine wave, one time for ±X, ±Y, ±Z axis
(5) 10-300 Hz, Sweep rate 10min, 30min for X,Y,Z axis

(40, 93.8)

(50, 50.4)

(65, 27.7)

Fig. Temperature and Relative humidity range

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 5 / 29

From 【液晶之家】— www.fpdclub.net

2. Optical Characteristics

The optical characteristics should be measured in a dark room or equivalent.

Measuring equipment : TOPCON BM-7,SPECTRORADIOMETER SR-3
(Ta = 25 ± 2°C, VDD=12V, fv= 60Hz, fDCLK=148.5MHz, Dim = 100%)
Item Symbol Condition Min. Typ. Max. Unit Note
Contrast Ratio (3)
C/R *2500 5000 -
(Center of screen) SR-3
Rising Tr - 12 70
Response Falling Tf - 8 18 (5)
msec
Time BM-7
G-to-G
Tg - 8 -
[AVE]
Luminance of White Normal (6)
YL 380 450 - cd/m2
(Center of screen) L,R=0 SR-3
U,D=0
Rx 0.639
Red
Ry Viewing 0.330
Angle
Gx 0.288
Green
Color Gy 0.604
TYP. TYP. (7),(8)
Chromaticity
Bx -0.03 0.148 +0.03 SR-3
(CIE 1931)
Blue
By 0.057
Wx 0.280
White
Wy 0.285
(7)
Color Gamut - - 72 - %
SR-3
Color Temperature - - 10000 - K (7)
Gamma γ - 2.2 - SR-3

L 79 89 -
Hor.
Viewing R 79 89 - (8)
C/R≥10 Degree
Angle U 79 89 - SR-3
Ver.
D 79 89 -
Brightness Uniformity (4)
Buni - - 25 %
(9 Points) SR-3
* marked Items Value does not Specification above when “White stain” occurs at Center Point [Point ⑤ of Note 2.]

Note (1) Test Equipment Setup

The measurement should be executed in a stable, windless and dark room between
40min and 60min after lighting the back light at the given temperature for stabilization
of the back light. This should be measured in the center of screen.

Single lamp current @ Vdim = 100%

Environment condition : Ta = 25 ± 2 °C

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 6 / 29

From 【液晶之家】— www.fpdclub.net

 Photo detector
Photo detector Field

SR-3 1°
BM-7 2° Field

SR-3 : 50㎝
BM-7 : 50㎝

TFT - LCD Module

LCD Panel

The center of the screen

Note (2) Definition of test point

320 960 1600

Active Area
180 ⑨ ⑧ ⑦
Test Point
540 ⑥ ⑤ ④

900 ③ ② ①

Note (3) Definition of Contrast Ratio (C/R)

: Ratio of gray max (Gmax) & gray min (Gmin) at the center point ⑤ of the panel

G max
C/R
G min
Gmax : Luminance with all pixels white
Gmin : Luminance with all pixels black

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 7 / 29

From 【液晶之家】— www.fpdclub.net

 Note (4) Definition of 9 points brightness uniformity

( B max  B min)
Buni  100
B max
Bmax : Maximum brightness
Bmin : Minimum brightness

Note (5) Definition of Response time : Sum of Tr, Tf

Display data Black (data off) White (data on) White (data off)

TR TF
Optical Instruments
100%
Response
90%

10%
0%
TIME

Note (6) Definition of Luminance of White : Luminance of white at center point ⑤

Note (7) Definition of Color Chromaticity (CIE 1931)

Color coordinate of Red, Green, Blue & White at center point ⑤

Note (8) Definition of Viewing Angle

: Viewing angle range (C/R ≥10)

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 8 / 29

From 【液晶之家】— www.fpdclub.net

 3. Electrical Characteristics

3.1 TFT LCD Module

The connector for display data & timing signal should be connected.
Ta = 25°C ± 2 °C
Item Symbol Min. Typ. Max. Unit Note
Voltage of Power Supply VDD 11 12 13 V (1)
(a) Black - 450 -
Current (b) White - 700 900
of Power IDD mA (2),(3)
Supply (c) Mosaic - 700 -
(4) Max Pattern - 750 950
Vsync Frequency fV 47 60 62 Hz
Hsync Frequency fH 50 67.5 73 kHz
Main Frequency fDCLK 130 148.5 155 MHz
Rush Current IRUSH - - 5 A (4)

Note (1) The ripple voltage should be controlled under 10% of VDD.
(2) fV=60Hz, fDCLK = 148.5MHz, VDD = 12.0V, DC Current.
(3) Power dissipation check pattern (LCD Module only)
a) Black Pattern b) White Pattern c) Mosaic d)Max. Pattern

(4) Measurement Conditions

VDD
100%
90%

10%
GND

TRUSH=1ms
Rush Current IRUSH can be measured when TRUSH. is1ms

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 9 / 29

From 【液晶之家】— www.fpdclub.net

 3.2 Back Light Unit

The back light unit contains 4 CCFTs ( Cold Cathode Fluorescent Tube ).
The characteristics of lamps are shown in the following tables.
Ta=25 ± 2°C
Item Symbol Min. Typ. Max. Unit Note
Operating Life Time Hr 50,000 - - Hour (1)
Lamp Current Lc 11.0 - 16.0 mA -

Note (1) It is defined as the time to take until the brightness reduces to 50% of its original value.
[Operating condition : Ta = 25±2℃, IL = 14.0 mArms(typ.), For single lamp only. ]

Socket

HOT 1

HOT 1

LCD
Inverter
Module

HOT 4

HOT 4

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 10 / 29

From 【液晶之家】— www.fpdclub.net

 4. Block Diagram

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 11 / 29

From 【液晶之家】— www.fpdclub.net

5. Input Terminal Pin Assignment
5.1. Input Signal & Power Connector : IS050-C51B-C38(UJU)
Compatible with FI-RE51S-HF(JAE)

PIN No. Signal Description PIN No. Signal Description

1 Power VDD 26 LVE[0]P Even LVDS Signal +

2 Power VDD 27 LVE[1]N Even LVDS Signal -

3 Power VDD 28 LVE[1]P Even LVDS Signal +

4 Power VDD 29 LVE[2]N Even LVDS Signal -

5 Power VDD 30 LVE[2]P Even LVDS Signal +

6 GND GND 31 GND GND
7 GND GND 32 LVECLK- Even LVDS Clock-
8 GND GND 33 LVECLK+ Even LVDS Clock+
9 GND GND 34 GND GND
10 LVO[0]N Odd LVDS Signal - 35 LVE[3]N Even LVDS Signal -
11 LVO[0]P Odd LVDS Signal + 36 LVE[3]P Even LVDS Signal +
12 LVO[1]N Odd LVDS Signal - 37 N.C. No Connection
13 LVO[1]P Odd LVDS Signal + 38 N.C. No Connection
14 LVO[2]N Odd LVDS Signal - 39 GND GND
15 LVO[2]P Odd LVDS Signal + 40 SCL I2C SCL
16 GND GND 41 SDA I2C SDA
17 LVOCLK- Odd LVDS CLK - 42 VSYNC *V Sync Signal
18 LVOCLK+ Odd LVDS CLK + 43 B-INT Bus Release
19 GND GND 44 N.C. No Connection
20 LVO[3]N Odd LVDS Signal - 45 N.C. No Connection
21 LVO[3]P Odd LVDS Signal + 46 LUT SEL0 DCC LUT Select 0
22 N.C. No Connection 47 LUT SEL1 DCC LUT Select1
23 N.C. No Connection 48 LUT SEL2 DCC LUT Select2
24 GND GND 49 HSYNC H Sync Signal

25 LVE[0]N Even LVDS Signal - 50 TCON_RDY T-Con Ready

51 SEL1 SEC Internal Use Only

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 12 / 29

From 【液晶之家】— www.fpdclub.net

 ■ B-INT : I2C BUS RELEASE

Operation Description
LOW/OPEN SDA/SCL LINE BECOME HI-Z
HIGH USER CAN ACCESS EEPROM

■ DCC Look Up Table Selection

Description ( Based on DCC On)
Pin N.O. 48 47 46
LUT %(For Interpolate)
0 0 0 For 60Hz 100%
0 0 1 For 60Hz 100%X1.25

0 1 0 For 60Hz @ Low Temp. 100%X1.25

Select 0 1 1 For 60Hz @ Low Temp. (100%X1.25) X 1.25

bit 1 0 0 For 50Hz 100%

1 0 1 For 50Hz 100%X1.25

1 1 0
0%
1 1 1

■ TCON Ready

Operation Description
Low  High Normal Operation
High  Low Error Operation

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 13 / 29

From 【液晶之家】— www.fpdclub.net

 Note(1) Pin number starts from Right side

PCB
▼

Pin No. 1 Pin No. 51

#1 #51

connect name

#1 #51

Fig. Connector diagram

a. All GND pins should be connected together and also be connected to the LCD’s
metal chassis.
b. All power input pins should be connected together.
c. All NC pins should be separated from other signal or power.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 14 / 29

From 【液晶之家】— www.fpdclub.net

 5.2. Inverter Input Pin Configuration
Connector : 20022WR-14AML

Pin No. Pin Configuration(FUNCTION)

1 24V
2 24V
3 24V
4 24V
5 24V
6 GND
7 GND
8 GND
9 GND
10 GND
11 Inverter Operation Status Output
12 Inverter On/Off Control Signal
13 No Connection
14 External Dimming Control Signal

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 15 / 29

From 【液晶之家】— www.fpdclub.net

 5.3. Inverter Input Power Sequence & Specification
Specifications
Items Symbol Conditions Unit Note
Min. Typ. Max.
Input
Vin - 21.6 24.0 26.4 V Ta=25±3°C
Voltage
Input Vin=24V
ISAT - 3.25 3.80 A -
Current EX_DIM=100%
Lamp Vin=24V
IO 13.0 14.0 15.0 mArms -
Current EX_DIM=100%
Operating Vin=24V
FO 55.0 57.5 60.0 kHz -
Frequency EX_DIM=100%

Backlight ON 2.4 - 5.25

ENA V -
On/Off OFF -0.3 - 0.8
Dmax 100 - - Note 1
Dimming
Vin=24V
Duty Dmin 15 20 25 % -
EX_DIM=100%
Output
Dmin 10 - - Note 2
Open Lamp Vin=24V
Vopen 1305 - - Vrms Note 3
Voltage EX_DIM=100%
Striking Vin=24V
Tst 1.0 1.5 2.0 sec -
Time EX_DIM=100%
EX_DIM
FEX_DIM Vin=24.0V 120 150 180 Hz -
Frequency
PWM High (On) 2.4 - 5.25
Signal Vpwm V -
Amplitude Low (Off) -0.3 - 0.4

※ All data was approved after running 120minutes with LCM.

Note1. Duty Measurement [Duty(%) = Ton / T x 100]

Note 2. There are not shut down and flicker at 10% @ 150Hz.
There is not shut down at 5% @ 75Hz.
Note 3. Measurement Method : Check Vs on BLU Remaining all Lamps.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 16 / 29

From 【液晶之家】— www.fpdclub.net

 5.4 LVDS Interface

LVDS pin Odd Data Even Data

TxIN/RxOUT0 R2 R2

TxIN/RxOUT1 R3 R3

TxIN/RxOUT2 R4 R4

TxOUT/RxIN0 TxIN/RxOUT3 R5 R5

TxIN/RxOUT4 R6 R6

TxIN/RxOUT6 R7 R7

TxIN/RxOUT7 G2 G2

TxIN/RxOUT8 G3 G3

TxIN/RxOUT9 G4 G4

TxIN/RxOUT12 G5 G5

TxOUT/RxIN1 TxIN/RxOUT13 G6 G6

TxIN/RxOUT14 G7 G7

TxIN/RxOUT15 B2 B2

TxIN/RxOUT18 B3 B3

TxIN/RxOUT19 B4 B4

TxIN/RxOUT20 B5 B5

TxIN/RxOUT21 B6 B6

TxOUT/RxIN2 TxIN/RxOUT22 B7 B7

TxIN/RxOUT24 HSYNC HSYNC

TxIN/RxOUT25 VSYNC VSYNC

TxIN/RxOUT26 DEN DEN

TxIN/RxOUT28 R0 R0

TxIN/RxOUT29 R1 R1

TxIN/RxOUT30 G0 G0

TxOUT/RxIN3 TxIN/RxOUT31 G1 G1

TxIN/RxOUT32 B0 B0

TxIN/RxOUT33 B1 B1

TxIN/RxOUT34 Reserved Reserved

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 17 / 29

From 【液晶之家】— www.fpdclub.net

5.5 Input Signals, Basic Display Colors and Gray Scale of Each Color
DATA SIGNAL
GRAY
DISPLAY
COLOR RED GREEN BLUE SCALE
(8bit)
LEVEL
R0 R1 R2 R3 R4 R5 R6 R7 G0 G1 G2 G3 G4 G5 G6 G7 B0 B1 B2 B3 B4 B5 B6 B7

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -

BLUE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -

GREEN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -

BASIC CYAN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -
COLOR
RED 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 -

MAGENTA 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 -

YELLOW 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 -

WHITE 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 -

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R0

1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R1

DARK 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R2
GRAY ↑
: : : : : : : : : : : : : : : : : : R3~
SCALE
OF : : : : : : : : : : : : : : : : : : R252
RED ↓
LIGHT 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R253

0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R254

RED 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 R255

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G0

0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G1

DARK 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 G2
GRAY ↑
SCALE : : : : : : : : : : : : : : : : : : G3~
OF : : : : : : : : : : : : : : : : : : G252
GREEN ↓
LIGHT 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G253

0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G254

GREEN 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 G255

BLACK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 B0

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 B1

DARK 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 B2
GRAY ↑
: : : : : : : : : : : : : : : : : : B3~
SCALE
OF : : : : : : : : : : : : : : : : : : B252
BLUE ↓
LIGHT 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 1 1 1 1 1 1 B253

0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 B254

BLUE 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 B255

Note) Definition of Gray :

Rn : Red Gray, Gn : Green Gray, Bn : Blue Gray (n = Gray level)
Input Signal : 0 = Low level voltage, 1 = High level voltage

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 18 / 29

From 【液晶之家】— www.fpdclub.net

6. Interface Timing

6.1 Timing Parameters ( DE only mode )

SIGNAL ITEM SYMBOL MIN. TYP. MAX. Unit NOTE

Clock 1/TC 130 148.5 155 MHz -

Hsync Frequency FH 50 67.5 73 KHz -

Vsync FV 47 60 62 Hz -
Active
Display TVD - 1080 - lines -
Vertical Period
Display Term
Vertical
TVB 1100 1125 1480 Lines -
Total
Active
Display THD - 1920 - clocks -
Horizontal Period
Display Term
Horizontal
TH 2154 2200 2450 clocks -
Total

Note) This product is DE only mode. The input of Hsync & Vsync signal does
not have an effect on normal operation.
(1) Test Point : TTL control signal and CLK at LVDS Tx input terminal in system
(2) Internal VDD = 3.3V

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 19 / 29

From 【液晶之家】— www.fpdclub.net

 6.2 Timing diagrams of interface signal ( DE only mode )

TV

TVD TVB

DE

TH

THD

DE

DCLK
TC

DATA
SIGNALS

TC
TCH TCL

DCLK 0.5
VCC

TDS TDH

DISPLAY 0.5
DATA
VCC

TES

DE 0.5
VCC

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 20 / 29

From 【液晶之家】— www.fpdclub.net

6.3 Power ON/OFF Sequence

To prevent a latch-up or DC operation of the LCD Module, the power on/off

sequence should be as the diagram below.

[UNIT : mS]

Min Max Min Max

T1 0.47 30 T8 30 -
T2 0 100 T9 500 -
T3 0 100 T10 50 -
T4 0.1 50 T11 100 -

T5 220 350 T12 0 50

T6 0 30 T13 0 300
T7 0 30 T14 1000 -
 The supply voltage of the external system for the Module input should be the same
as the definition of VDD.
 Apply the lamp voltage within the LCD operation range. When the back light turns on
before the LCD operation or the LCD turns off before the back light turns off,
the display may momentarily show abnormal screen.
 In case of VDD = off level,
please keep the level of input signals low or keep a high impedance.
 T14 should be measured after the Module has been fully discharged between power off
and on period.
 Interface signal should not be kept at high impedance when the power is on.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 21 / 29

From 【液晶之家】— www.fpdclub.net

8. Outline dimension (Front view)

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 22 / 29

From 【液晶之家】— www.fpdclub.net

Outline dimension (Rear View)

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 23 / 29

From 【液晶之家】— www.fpdclub.net

8. PACKING
※ Applied to SESL, SESL LCM Model
8.1 CARTON (Internal Package)
(1) Packing Form
Corrugated fiberboard box and corrugated cardboard as shock absorber
(2) Packing Method
Packing Box

Module(26EA)

Pallet

→ Direction be able to Open

8.2 Packing Specification
Item Specification Remark

1. 156Kg/LCD(26ea)
LCD Packing 26 ea / (Packing
2. 30kg/Packing Box(2set)
Box)
3. Packing Box Material : DW, SW

Desiccant (Drier) 2ea/LCD 10g/ea, Cobalt-dichloride-free

Pallet 1 Box / Pallet Pallet weight : 8kg
Packing Direction Vertical -

Total Pallet Size H x V x height 1150mm x 850mm x 1125mm

Pallet(8kg) + Module( 26 x 6 = 156kg) +

Total Pallet Weight 194.52kg Packing BOX(15 x 2 = 30kg) +
Desiccant(0.02kg x 26 = 0.52kg)

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 24 / 29

From 【液晶之家】— www.fpdclub.net

 ※ Applied to SELSK Model
8.3 CARTON (Internal Package)
(1) Packing Form
Corrugated fiberboard box and corrugated cardboard as shock absorber
(2) Packing Method
Packing Pallet Box

8.4 Packing Specification

Item Specification Remark
1. 144Kg/LCD(24ea)
2. 14kg/Cushion Set(4ea)
LCD Packing 24 ea / (Packing-
3. 6.7kg/Packing-Pallet Box(1ea)
Pallet Box)
4. Cushion Material : EPS
5. Packing Pallet Box Material : DW4
Desiccant (Drier) 2ea/LCD 10g/ea, Cobalt-dichloride-free
Pallet 1 Box / Pallet Pallet weight : 8kg
Packing Direction Vertical -

Total Pallet Size H x V x height 1150mm x 985mm x 1159mm

Pallet(8kg) + Module( 24 x 6 = 144kg) +

Total Pallet Weight 173.18kg Cushion(14kg) + Pallet-BOX(6.7kg) +
Desiccant(0.02kg x 24 = 0.48kg)

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 25 / 29

From 【液晶之家】— www.fpdclub.net

9. MARKING & OTHERS

A nameplate bearing followed by is affixed to a shipped product at the specified

location on each product.
(1) Parts number : LTY320HM01-XXX
(2) Revision: One letters
(3) Lot number : X X X X XXX XX X

Cell Position No. (In the Glass)

Glass No. (In the one Lot)
Lot No. (Glass)
Month
Year (Note1)
Product code
(4) Nameplate Indication Line

Week code : 05 29
LTY320HM01
week
year
40mm
XXXXXX XXXXXXXXXX xxx
Revision code
Lot number
LTY320HM01XXX

80mm
(5) Packing box attach

100mm
LTY320HM01-XXX Part number

XXXX Revision code

xx Actual Quantity

Box serial number

0703
(6) Others
1. After service part
Lamps cannot be replaced because of the narrow bezel structure.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 26 / 29

From 【液晶之家】— www.fpdclub.net

10. General Precautions
10.1 Handling

(a) When the Module is assembled, it should be attached to the system firmly
using all mounting holes. Be careful not to twist and bend the Module.

(b) Because the inverter use high voltage, it should be disconnected from power
before it is assembled or disassembled.

(c) Refrain from strong mechanical shock and / or any force to the Module.
In addition to damage, this may cause improper operation or damage to the Module
and CCFT back light.

(d) Note that polarizers are very fragile and could be damage easily.
Do not press or scratch the surface harder than a HB pencil lead.

(e) Wipe off water droplets or oil immediately. If you leave the droplets for a long
time, staining or discoloration may occur.

(f) If the surface of the polarizer is dirty, clean it using absorbent cotton or soft cloth.

(g) Desirable cleaners are water, IPA(Isopropyl Alcohol) or Hexane.

Do not use Ketone type materials(ex. Acetone), Ethyl alcohol, Toluene, Ethyl acid
or Methyl chloride. It might permanent damage to the polarizer due to chemical
reaction.

(h) If the liquid crystal material leaks from the panel, it should be kept away
from the eyes or mouth . In case of contact with hands, legs or clothes, it must
be washed away with soap thoroughly.

(i) Protect the Module from static, or the CMOS Gate Array IC would be damaged.

(j) Use finger-stalls with soft gloves in order to keep display clean during the
incoming inspection and assembly process.

(k) Do not disassemble the Module.

(l) Do not pull or fold the lamp wire.

(m) Do not adjust the variable resistor located on the Module.

(n) Protection film for polarizer on the Module should be slowly peeled off just before use
so that the electrostatic charge can be minimized.

(o) Pins of I/F connector should not be touched directly with bare hands.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 27 / 29

From 【液晶之家】— www.fpdclub.net

 10.2 Storage

(a) Do not leave the Module in high temperature, and high humidity for a long time.
It is highly recommended to store the Module with temperature from 0 to 35℃
and relative humidity of less than 70%.

(b) Do not store the TFT-LCD Module in direct sunlight.

(c) The Module should be stored in a dark place. It is prohibited to apply sunlight or
fluorescent light in storing.

10.3 Operation

(a) No Connection or disconnect the Module in the "Power On" condition.

(b) Power supply should always be turned on/off by the "Power on/off sequence"

(c) Module has high frequency circuits. Sufficient suppression to the electromagnetic
interference should be done by system manufacturers. Grounding and shielding methods
may be important to minimize the interference.

(d) The cable between the back light connector and its inverter power supply should
be connected directly with a minimized length. A longer cable between
the back light and the inverter may cause lower luminance of lamp(CCFT) and
may require higher startup voltage(Vs).

10.4 Operation Condition Guide

(a) The LCD product should be operated under normal conditions.

Normal condition is defined as below;
- Temperature : 20±15℃
- Humidity : 55±20%
- Display pattern : continually changing pattern (Not stationary)

(b) If the product will be used in extreme conditions such as high temperature,
humidity, display patterns or operation time etc.., It is strongly recommended
to contact SEC for Application engineering advice. Otherwise, its reliability and
function may not be guaranteed. Extreme conditions are commonly found at
Airports, Transit Stations, Banks, Stock market, and Controlling systems.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 28 / 29

From 【液晶之家】— www.fpdclub.net

 10.5 Others

(a) Ultra-violet ray filter is necessary for outdoor operation.

(b) Avoid condensation of water. It may result in improper operation or disconnection

of electrode.

(c) Do not exceed the absolute maximum rating value. ( supply voltage variation,
input voltage variation, variation in part contents and environmental temperature,
and so on)
Otherwise the Module may be damaged.

(d) If the Module keeps displaying the same pattern for a long period of time,
the image may be "sticked" to the screen.
To avoid image sticking, it is recommended to use a screen saver.

(e) This Module has its circuitry PCB's on the rear side and should be handled
carefully in order not to be stressed.

(f) Please contact SEC in advance when you display the same pattern for a long time.

MODEL LTY320HM01 Doc. No 05-000-G-100316 Page 29 / 29

From 【液晶之家】— www.fpdclub.net