SC56-21SRWA

14.22 mm (0.56 inch) Single Digit Numeric Display

DESCRIPTIONS PACKAGE DIMENSIONS

z The Super Bright Red source color devices are made
with Gallium Aluminum Arsenide Red Light Emitting
Diode
z Electrostatic discharge and power surge could
damage the LEDs
z It is recommended to use a wrist band or
anti-electrostatic glove when handling the LEDs
z All devices, equipments and machineries must be
electrically grounded

FEATURES
z 0.56 inch digit height
z Low current operation
z Excellent character appearance
z Easy mounting on P.C. boards or sockets
z Mechanically rugged
z Standard: gray face, white segment
z RoHS compliant

APPLICATIONS
z Home and smart appliances
z Display time and digital combination
z Industrial and instrumental applications
z Numeric status

ATTENTION
Observe precautions for handling
electrostatic discharge sensitive devices

Notes:
1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted.
2. The specifications, characteristics and technical data described in the datasheet are subject to change
without prior notice.

SELECTION GUIDE
Emitting Color Iv (ucd) @ 10mA [1]
Part Number Lens Type Description
(Material) Min. Typ.

14000 34000
SC56-21SRWA ■ Super Bright Red White Diffused
Common Cathode,
(GaAlAs) Rt. Hand Decimal
*5600 *10000

Notes:
1. Luminous intensity / luminous Flux: +/-15%.
* Luminous intensity value is traceable to CIE127-2007 standards.

© 2018 Kingbright. All Rights Reserved. Spec No: DSAP5483 / 1301001137 Rev No: V.1A Date: 07/30/2018 Page 1 / 4
 SC56-21SRWA
ELECTRICAL / OPTICAL CHARACTERISTICS at TA=25°C
Value
Parameter Symbol Emitting Color Unit
Typ. Max.

Wavelength at Peak Emission IF = 10mA λpeak Super Bright Red 655 - nm

Dominant Wavelength IF = 10mA λdom [1] Super Bright Red 640 - nm

Spectral Bandwidth at 50% Φ REL MAX

Δλ Super Bright Red 20 - nm
IF = 10mA

Capacitance C Super Bright Red 45 - pF

Forward Voltage IF = 10mA VF [2] Super Bright Red 1.8 2.3 V

Reverse Current (VR = 5V) IR Super Bright Red - 10 uA

Notes:
1. The dominant wavelength (λd) above is the setup value of the sorting machine. (Tolerance λd : ±1nm. )
2. Forward voltage: ±0.1V.
3. Wavelength value is traceable to CIE127-2007 standards.
4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure.

ABSOLUTE MAXIMUM RATINGS at TA=25°C

Parameter Symbol Value Unit

Power Dissipation PD 75 mW

Reverse Voltage VR 5 V

Junction Temperature Tj 115 °C

Operating Temperature Top -40 To +85 °C

Storage Temperature Tstg -40 To +85 °C

DC Forward Current IF 30 mA

Peak Forward Current IFM [1] 155 mA

Electrostatic Discharge Threshold (HBM) - 3000 V

Lead Solder Temperature [2] 260°C For 3-5 Seconds

Notes:
1. 1/10 Duty Cycle, 0.1ms Pulse Width.
2. 2mm below package base.
3. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033.

© 2018 Kingbright. All Rights Reserved. Spec No: DSAP5483 / 1301001137 Rev No: V.1A Date: 07/30/2018 Page 2 / 4
 SC56-21SRWA
TECHNICAL DATA
RELATIVE INTENSITY vs. WAVELENGTH
Red
100%
Ta = 25 °C
Relative Intensity (a. u.)

80%

60%

40%

20%

0%
350 400 450 500 550 600 650 700 750 800
Wavelength (nm)

SUPER BRIGHT RED

Forward Current vs. Luminous Intensity vs. Forward Current Derating Curve Luminous Intensity vs.
Forward Voltage Forward Current Ambient Temperature
20 2.5 50 2.5
Permissible forward current (mA)
Luminous intensity normalised

Luminous intensity normalised

Ta = 25 °C Ta = 25 °C
16 2.0 40 2.0
Forward current (mA)

at Ta = 25 °C
12 1.5 30 1.5
at 10mA

8 1.0 20 1.0

4 0.5 10 0.5

0 0.0 0 0.0
1.3 1.5 1.7 1.9 2.1 2.3 0 4 8 12 16 20 -40 -20 0 20 40 60 80 100 -40 -20 0 20 40 60 80 100
Forward voltage (V) Forward current (mA) Ambient temperature (°C) Ambient temperature (°C)

RECOMMENDED WAVE SOLDERING PROFILE Soldering General Notes

1. Through-hole displays are incompatible with reflow soldering.
2. If components will undergo multiple soldering processes,
or other processes where the components may be subjected
to intense heat, please check with Kingbright for compatibility.

CLEANING
1. Mild "no-clean" fluxes are recommended for use in soldering.
2. If cleaning is required, Kingbright recommends to wash
components with water only. Do not use harsh organic
solvents for cleaning because they may damage the plastic
parts .
3. The cleaning process should take place at room temperature
and the devices should not be washed for more than one
minute.
Notes: 4. When water is used in the cleaning process, Immediately
1. Recommend pre-heat temperature of 105°C or less (as measured with a thermocouple
attached to the LED pins) prior to immersion in the solder wave with a maximum solder bath remove excess moisture from the component with forced-air
temperature of 260°C
2. Peak wave soldering temperature between 245°C ~ 255°Cfor 3 sec (5 sec max). drying afterwards.
3. Do not apply stress to the epoxy resin while the temperature is above 85°C.
4. Fixtures should not incur stress on the component when mounting and during soldering process.
5. SAC 305 solder alloy is recommended.
6. No more than one wave soldering pass.
7. During wave soldering, the PCB top-surface temperature should be kept below 105°C.

© 2018 Kingbright. All Rights Reserved. Spec No: DSAP5483 / 1301001137 Rev No: V.1A Date: 07/30/2018 Page 3 / 4
 SC56-21SRWA
PACKING & LABEL SPECIFICATIONS

THROUGH HOLE DISPLAY MOUNTING METHOD

Lead Forming
Do not bend the component leads by hand without
proper tools. The leads should be bent by clinching the
upper part of the lead firmly such that the bending force
is not exerted on the plastic body.

Installation
1. The installation process should not apply stress to the lead terminals.
2. When inserting for assembly, ensure the terminal pitch matches the substrate board's hole pitch to prevent spreading or pinching
the lead terminals. (Fig.1)
3. The component shall be placed at least 5mm from edge of PCB to avoid damage caused excessive heat during
wave soldering.(Fig.2)

CIRCUIT DESIGN NOTES

1. Protective current-limiting resistors may be necessary to operate the LEDs within the specified range.
2. LEDs mounted in parallel should each be placed in series with its own current-limiting resistor.(Fig.3)
3. The driving circuit should be designed to protect the LED against reverse
voltages and transient voltage spikes when the circuit is powered up
or shut down.
4. The safe operating current should be chosen after considering the
maximum ambient temperature of the operating environment.
5. Prolonged reverse bias should be avoided, as it could cause metal
migration, leading to an increase in leakage current or causing
a short circuit.

PRECAUTIONARY NOTES
1. The information included in this document reflects representative usage scenarios and is intended for technical reference only.
2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to
the latest datasheet for the updated specifications.
3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If
customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues.
4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening
liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance.
5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright.
6. When any special process such as potting is required for LED assembly, please consult with Kingbright representative before proceeding.
7. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes

© 2018 Kingbright. All Rights Reserved. Spec No: DSAP5483 / 1301001137 Rev No: V.1A Date: 07/30/2018 Page 4 / 4