Scribd Logo
Upload

Welcome to Scribd!

  • 149 views

    Dact-E3: Analog and Networking Systems

    Uploaded by

    enriquealugov

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Dact-E3: Analog and Networking Systems

    Uploaded by

    enriquealugov
    149 views2 pages

    Original Title

    9020-0610

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    149 views2 pages

    Dact-E3: Analog and Networking Systems

    Uploaded by

    enriquealugov

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Analog and Networking Systems

    DACT-E3
    Digital Alarm Communicator Transmitter
    General
    The Digital Alarm Communicator Transmitter (DACT-E3) is a digital communications
    circuit. It is an optional component of the following systems.

    • E3 Series® Expandable Emergency Evacuation System


    • S3 Series Small Addressable Fire Alarm Control Panel
    The DACT-E3 sends digital signals over the telephone network that transmits to a
    central station. This module can be located in the main cabinet or remotely located via
    a local RS-485 serial interface.

    The DACT-E3 is compatible with digital alarm communicator receivers (DACRs) that
    receive the following signaling formats:
    • SIA DC8 • 3+1 2300 Hz
    • SIA DCS20 • 4+2 1400 Hz
    • Ademco Contact ID • 4+2 2300 Hz
    • 3+1 1400 Hz DACT-E3
    In addition to the DACT-E3 being compatible with digital signaling formats, the DACT-
    E3 features numerous formats for communication to a central station. As a digital
    communicator, the DACT-E3 complies with FCC Part 8, Telecommunication
    Standards for DC and AC Ringer Equivalence.

    Installation
    The DACT-E3 is adaptable for installation in the standard E3 Series and S3 Series
    System cabinets. Typically, the DACT-E3 module mounts on standoffs on top of the
    left side of the ILI-MB-E3/ILI95-MB-E3 or SLP (Smart Loop Panel) module. Either
    unit can be easily connected to the backbox or sub-assembly plate depending on the
    cabinet module.

    For instructions on how to install the DACT-E3, refer to the following documents:
    • E3 Series Expandable Emergency Evacuation Manual, P/N:LS10080-051GF-E
    • DACT-E3 Installation Instructions, P/N:9000-0581
    • S3 Series (Small Addressable Fire Alarm Control Panel) UL Listing Document,
    P/N:LS10005-051GF-E
    Ordering Information
    DACT-E3: Digital Alarm Communicator Transmitter

    FEATURES & BENEFITS


    • Listed under UL®® • Communicates with • Sends information in a • Performs on and off- • Compatible with the
    Standard 864, 9th the following sub- variety of formats hook status to the IPDACT Internet
    Edition assemblies via the RS- (including full Contact phone lines Communicator
    485: ID)
    • Transmits and verifies • Traces proper central
    data to the central - E3 Series • Offers pre- station “ACK” and
    station - ILI-MB-E3 programmed dialing to “Kiss-off” tone
    - ILI95-MBE3 the central station
    • Activates hang-up and
    - S3 Series, SLP phone number release phone lines
    DACT-E3 Technical Specifications
    SYSTEM STANDARDS For a complete listing of all
    compliance approvals and
    Operating Voltage: 24 VDC (from the PM-9/ The DACT-E3 is designed to comply with the following certifications, please visit:
    PM-9G power supply) standard: http://www.gamewell-
    UL Standard: UL 864 9th Edition fci.com/en-US/
    Operating Current: 0.018 amp documentation/Pages/
    AGENCY LISTINGS AND APPROVALS Listings.aspx
    Alarm Current: 0.018 amp
    Operating Temperature: 32° to 120° F (0° to 49° C) These listings and approvals apply to the modules E3 Series® and Gamewell-FCI ®
    Relative Humidity: 0 to 93%, non-condensing at specified in this document. In some cases, certain are registered trademarks of
    modules or applications may not be listed by certain Honeywell International Inc.
    90° F (32° C) approval agencies, or listing may be in process. Consult
    UL® is a registered trademark
    TEMPERATURE AND HUMIDITY RANGES the factory for the latest listing status.
    of Underwriters Laboratories
    UL Listed: S1869 Inc.
    This system meets NFPA requirements for opera-
    tion at 0 – 49°C/32 – 120°F and at a relative FM Approved: 3025415
    This document is not intended
    humidity 93% ± 2% RH (noncondensing) at 32°C ± MEA Approved, Fire Dept. of New York: COA# 6077 to be used for installation
    2°C (90°F ± 3°F). However, the useful life of the CSFM: 7165-1703-0125 purposes. We try to keep our
    system's standby batteries and the electronic com- product information up-to-
    ponents may be adversely affected by extreme tem- City of Chicago: Class 1, Class 2 and High Rise
    date and accurate. We cannot
    perature ranges and humidity. Therefore, it is City of Denver
    cover all specific applications
    recommended that this system and its peripherals or anticipate all requirements.
    be installed in an environment with a normal room All specifications are subject to
    temperature of 15 – 27°C/60 – 80°F. change without notice.

    For more information


    Learn more about Gamewell-FCI’s DACT-E3 and other products
    available by visiting www.Gamewell-FCI.com

    Honeywell Gamewell-FCI
    12 Clintonville Road
    Northford, CT 06472-1610
    203.484.7161
    9020-0610 | L | 09/17
    www.honeywell.com ©2017 Honeywell International Inc.

    You might also like