Sigman Camouflage Sop
Sigman Camouflage Sop
Sigman Camouflage Sop
Geoff Ball
Garrett Boyce
Evan Kolodziejczak
Joseph Livi
Walker Mills
Paul Nichols
Zach Schwartz
Chad Skaggs
Matthew Shibata
Eric Todorski
Brian Walsh
Process
Premise
The threat has changed. Our adversaries, large and small, now integrate ISR sensors, especially
UAS, with long-range precision fires. For U.S. forces, this is the end of guaranteed air superiority.
Operations have changed. Littoral Operations in a Contested Environment (LOCE) and Expeditionary
Advanced Base Operations (EABO) require Fleet Marine Forces to support Navy sea control
missions.
Marines will seize key maritime terrain—Expeditionary Advanced Bases (EABs)—in order to establish
fires, ISR, aircraft, logistics, C2, or air and missile defense sites. These distributed EABs, operating
under the arc of enemy long-range precision fires, will expand the Fleet’s sea control, challenge the
enemy’s ability to target us, and free ships for other missions.
Outside the EABO concept, while conducting traditional amphibious operations or sustained
operations ashore—even against unsophisticated adversaries—Marines will still face the threat of
advanced sensors and long-range precision fires. UAS are everywhere.
For any mission, any adversary, and any environment, units must ruthlessly reduce their signature.
Battle positions and operating bases must be small, dispersed, well-camouflaged, and temporary.
The purpose of this SOP is to reduce the physical signature of the infantry battalion. We can reduce,
but never completely mask our signature. We will avoid observation to protect our combat power. The
signature of the infantry battalion, with 700 Marines and few vehicles, is less than other units of the
GCE, less than the equipment-heavy units of the ACE and LCE, and far less than any partnered Army
or Navy units.
Camouflage discipline includes light discipline, heat discipline, noise discipline, trash discipline,
and movement discipline.
Scope of this SOP
The infantry battalion. Overhead UAS and ground-based sensor threats. Precision missile (ballistic
missile and LACM), rocket, artillery, and mortar fires threats. Urban, woodland / jungle, and desert
environments, but NOT arctic / snow.
The Marine Corps Concept for Signature Management, 2017, defines three types of signatures:
physical, technical, and administrative. This SOP addresses ONLY the physical signature.
UAS identification is out of scope. Counter-UAS attack is out of scope. EMCON is out of scope.
Decoys and tactical deception are out of scope. Redundant positions are out of scope.
Field-expedient painting of equipment is out of scope.
This Camouflage SOP is a collective effort. If you can improve this document, send us your ideas or
join the online Google Doc.
Brendan McBreen
[email protected]
1 August 2020
“The majority of UAS...are used to detect and identify targets for other weapons… Solutions
such as camouflage and smoke can… defeat both attack UAS and fires enabled by UAS.”
2. How To
2.1 CAMOUFLAGE a Helmet
2.2 CAMOUFLAGE a Rifle
2.3 CAMOUFLAGE Equipment
2.4 CUT Vegetation
2.5 DEPLOY a Camouflage Ghillie Blanket
2.6 CAMOUFLAGE a Bivouac
2.7 CAMOUFLAGE a Fighting Position
2.8 CAMOUFLAGE a Vehicle
2.9 CAMOUFLAGE a CP
2.10 CAMOUFLAGE a TAA
3. Train
3.1 CONDUCT a Field Exercise
3.2 ESTABLISH Training Standards
3.3 COLLECT Own-Force Signature
4. Understand
4.1 Adversary UAS
4.2 Adversary Satellites
4.3 Adversary Missiles
4.4 Adversary Rockets, Artillery, and Mortars
4.5 Adversary Naval Threats
4.6 Adversary Fire Networks
4.7 U.S. Air and Missile Defense
5. Reference
5.1 Glossary
5.2 Bibliography
5.3 UAS Imagery of Russian Units
5.4 UAS Imagery of Marine Units
SIGMAN Camouflage SOP:
Chapter 1: Procedures
www.warfighting.us
SOP
CAMOUFLAGE Standards
Purpose. To REDUCE the physical signature (visual, IR thermal, and radar) of the unit IOT AVOID
being observed and targeted by the adversary.
Standards
1. ALL Marines:
CAMOUFLAGE your helmet. See CAMOUFLAGE a Helmet.
CARRY a camouflage ghillie blanket. See DEPLOY a Camouflage Ghillie Blanket.
CAMOUFLAGE your personal equipment and uniform. See CAMOUFLAGE Equipment.
MASK the shine on your optics and equipment.
SILENCE your gear.
2. ALL NCOs:
TRAIN your Marines on this SOP.
TRAIN your Marines on fieldcraft.
TRAIN your Marines on camouflage discipline. Camouflage discipline includes light discipline,
heat discipline, noise discipline, trash discipline, and movement discipline.
3. ALL SNCOs:
TRAIN your Marines on this SOP. INSPECT and CORRECT your Marines on this SOP.
MEMORIZE the Camouflage Inspection Checklist standards.
ENFORCE your Marines’ camouflage discipline. Camouflage discipline includes light
discipline, heat discipline, noise discipline, trash discipline, and movement discipline.
4. ALL drivers:
CARRY a camouflage net on your vehicle roof. See CAMOUFLAGE a Vehicle.
CAMOUFLAGE your vehicle if you are stopped for more than one hour.
DISPERSE while moving. DISPERSE when stopped. DISPERSE irregularly when parked.
Standard dispersion is three vehicle lengths.
1-1
PLAN concealed routes in woodlines, wadis, and riverbeds.
PLAN concealed stops in the shadows of trees or buildings.
LOWER speed to reduce dust signatures. PUT larger vehicles in front so their dust masks the
rest of the convoy.
BRIEF and REHEARSE the REDEYE UAS Drill. See REDEYE UAS Drill.
BRIEF and REHEARSE the HAWKEYE Convoy Drill. See HAWKEYE Camouflage Drill.
ASSIGN an air guard. See Air Guard SOP. ENFORCE movement discipline.
Notes
Attached unit leaders are responsible for the training and camouflage discipline of their people.
As a tenant in a base camp, unit leaders discuss SIGMAN issues with the camp commandant.
1-2
SOP
ALL unit SOPs and camouflage TTPs CONFORM to the following fundamental processes.
1. DISPERSE into multiple small elements. This is the most important step.
BE indistinguishable—unable to be identified as different—IOT avoid being targeted.
ASSUME you are being watched.
DISPERSE individuals, vehicles, and positions irregularly. DISPLACE often.
3. OPERATE at night.
Camouflage discipline includes light discipline. TRAIN in night operations, with NVGs, lasers,
and camouflage ghillie blankets. OPERATE in rain, fog, wind, and dust when UAS cannot fly.
OPERATE at dawn or dusk when shadows are long, sun glare is high, and thermal crossover
masks your heat signature. KNOW the daily light levels.
7. PLAN to operate under UAS. Think overhead. Hills block visual, thermal, and radar
observation, but the biggest threat is overhead UAS. PLAN concealed routes and positions.
PLAN operations at critical times. MINIMIZE logistics requirements. PLAN resupply events.
1-3
8. INSPECT your signature from the enemy’s point of view. USE binoculars, NVGs, thermal
scopes, and UAS.
COUNTER adversary HUMINT, OSINT, and ELINT efforts. This information cues ISR
platforms. Reduce the signature of your unit so that the adversary does NOT prioritize his ISR
assets against you.
References
ATP 3-37.34 / MCTP 3-34C Survivability Operations, 16 Apr 2018. 190 pages.
1-4
SOP
Conditions. The unit is stationary, operating at a base camp, TAA, or BP. Or the unit is moving,
conducting footmobile operations, NOT in contact with the enemy. For convoy operations, see the
HAWKEYE Convoy Drill.
Standard. In 20 minutes, the unit’s physical signature fades to zero. The unit cannot be seen or heard
by a ground or air adversary 1000m away.
Equipment. Each Marine and each vehicle carries the camouflage equipment they need.
Trigger. The unit leader calls the codeword and the time: “HAWKEYE 1520!”
Only the unit leader can stop the current mission. When he or she makes the deliberate decision to
trigger the drill—because of enemy action, an intelligence report, or as a preparation for combat—all
movement stops for 40 minutes and HAWKEYE becomes the mission.
The mission of the HAWKEYE camouflage drill is to disrupt the enemy’s intelligence, surveillance,
and reconnaissance units. Any scheduled activities by subordinate units are delayed.
Process
All units, all Marines, and all vehicles CEASE all activities.
Marines move to their defensive Stand-To positions, or, if moving, find a hasty position.
Slowly. Do NOT run. Do NOT increase the physical signature of the unit.
Responsibilities
1-5
Unit leaders are responsible for their unit’s signature. NCOs camouflage their units and equipment.
SNCOs inspect and correct. An Air Guard is posted.
Notes
HAWKEYE is NOT a UAS immediate action (IA) drill. See REDEYE Drill.
HAWKEYE is NOT a counter-UAS (C-UAS) attack. See LONGBOW C-UAS Drill.
HAWKEYE can be integrated into a unit’s existing Stand-To Drill.
EMCON is a separate drill which may be conducted simultaneously.
In order to meet the 20 minute standard, units must already have good camouflage discipline.
HAWKEYE should be a scheduled event to camouflage the unit when occupying a TAA or BP.
In a TAA, no units depart during the drill. Units arriving stop and camouflage in place.
Camouflage should be a distinct activity, supervised, timed, and inspected to a standard. Camouflage
is not an optional action, attempted indifferently, as time permits.
Related Processes
REDEYE Drill directs the unit to freeze and then operate under UAS observation.
LONGBOW C-UAS Drill directs the unit to attack a UAS.
HAWKEYE Convoy Drill directs a convoy to stop and camouflage.
Stand-To Drill directs the unit to occupy prepared fighting positions.
1 Aug 2020
1-6
SOP
Conditions. The unit is moving by convoy, NOT in contact with the enemy.
Standard. The unit cannot be seen or heard by a ground or air adversary 1000m away.
Equipment. Each Marine and each vehicle has the camouflage equipment they need.
Trigger. The unit leader calls the codeword and the time: “HAWKEYE the convoy 1520!”
Only the unit leader can stop the convoy. Moving is the best method to avoid being targeted, but
stopping is best to avoid detection. When the unit leader makes the deliberate decision to trigger the
drill, all movement stops for 40 minutes and HAWKEYE becomes the mission.
Process
Notes
1-7
Camouflage is only the last step to reduce the signature of a convoy. DISPERSE into multiple small
elements. Serials should be twelve vehicles or less. PLAN concealed routes. Use woodlines, wadis,
and riverbeds. OPERATE at night. POST an air guard.
Camouflage discipline includes light discipline, heat discipline, noise discipline, trash discipline, and
movement discipline.
1 Aug 2020
1-8
SOP
Standard. The unit FREEZES. In 5 minutes, the unit leader decides what to do.
Equipment. NONE.
Trigger. An adversary UAS is sighted. Any Marine calls the codeword and the location:
“REDEYE. UAS at one o’clock!” or “REDEYE. UAS to the west, over the river.”
Process
GO prone if you are on foot in the open. Minimize your shadow. COVER yourself with a
camouflage ghillie blanket, poncho, or tarp.
STAY behind and under the trees if you are in the woods. PUT something between you and
the UAS. STAY inside if you are in the city. STAY away from the windows.
AVOID looking up immediately. An obvious feature of aerial photos is upturned faces. Faces
shine, eye protection reflects light, and optics reflect light. Cover all optics. Cover the lens of
the RCO with a kill-flash (honeycomb).
or
1-9
b. “CONTINUE the mission.” They have seen us and we will operate under adversary
observation. The unit leader refuses to let his unit be suppressed or disrupted by an
adversary UAS.
or
c. “ATTACK the UAS. LONGBOW team up!” C-UAS actions are a separate process. See
LONGBOW C-UAS Drill.
or
See example UAS Report format in Table 3-1 of ATP 3-01.8 Techniques for Combined Arms
, 29 July 2016.
for Air Defense
Responsibilities
Although an air guard is always posted, any Marine can call REDEYE. NCOs enforce camouflage
discipline. SNCOs inspect and correct.
The unit leader decides on the response to adversary UAS. This decision must be based on an
understanding of the adversary: kill chain, habits, capabilities, ROE and TTPs. REDEYE requires a
critical combat decision when the unit is operating under the arc of the adversary’s long-range
precision fires.
“Does he see me?” is NOT the question.The unit leader needs to assess “What will he do with this
information?” Has he been sighted by an enemy squad or an enemy battalion? A fire network? Does
the adversary use UAS to recon for a ground attack, call for fire, or solely BDA?
Notes
REDEYE is a UAS immediate action (IA) drill, executed automatically. REDEYE for small UAS is no
different than for large UAS. Identification of the specific UAS is not required. Often, an adversary
UAS will be heard before it is seen.
REDEYE is executed at night. A UAS operating at night must be assumed to have IR thermal sights.
REDEYE is NOT the same as AIR ATTACK. Air defense warning conditions (RED, YELLOW, WHITE)
and weapons control status (TIGHT, HOLD, FREE) do NOT apply to UAS. The air attack drill—three
horns terminated by an “All Clear” signal—assumes that the enemy aircraft will be overhead for only
minutes. With multiple, persistent UAS overhead, we cannot make that assumption.
1-10
SOP
Process
1. ALERT. “LONGBOW team up!” The unit leader calls the designated C-UAS team.
Only the unit leader can make the deliberate decision to attack the UAS. Generally, you shoot
only if you think you’ve been seen, because engaging a UAS unmasks your position.
2. ATTACK. Shoot at the UAS. The LONGBOW C-UAS team attacks the UAS.
3. REPORT. The result of the UAS encounter is reported to the S-2 and HHQ.
See example UAS Report format in Table 3-1 of ATP 3-01.8 Techniques for Combined Arms
for Air Defense, 29 July 2016.
Notes
The LONGBOW counter-UAS (C-UAS) SOP is an active C-UAS measure. It is NOT a UAS immediate
action (IA) drill. See REDEYE UAS Drill.
C-UAS weapons are under development. Even when fielded, many units will NOT have C-UAS
capability. In 2020, Marine infantry units, with no active C-UAS weapons, must rely on direct-fire
weapons and passive responses to adversary UAS.
1-11
The LONGBOW C-UAS team is an additional duty assigned to an existing unit.
Marines NOT involved in C-UAS actions should maintain camouflage discipline.
Low, small, and slow UAS are flown by the adversary from nearby clearings and hilltops. Aggressive
patrolling of key terrain can push adversary UAS operators away from your unit. The LONGBOW
C-UAS team should BPT patrol and pursue nearby UAS operators.
LONGBOW C-UAS procedures and communications need to follow air and missile defense (AMD)
antiair doctrine. AMD terms such as engage, friendly, and unknown have well-defined meanings and
must be used precisely. See:
MCRP 3-30B.1 Brevity: Multi-Service TTPs for Brevity Codes, 1 May 2020.
Defines standard fire control orders: engage, cease engagement, hold fire, resume
fire, cease fire, and cover.
See also JP 3-01 Countering Air and Missile Threats, 2 May 2018.
See also JP 3-09.3 Close Air Support, 25 Nov 2014.
1-12
SOP
1. Every separate unit POSTS an air guard—at all times, day and night—for all operations. If two
or more air guard teams are posted then sectors are assigned.
2. The air guard WATCHES and LISTENS for adversary UAS. The air guard KNOWS the alert
process. See REDEYE UAS Drill. The air guard may or may NOT be trained in UAS
recognition.
4. The air guard duty rotates, like any other duty. It is NOT a sleeping post. Air guard may be an
additional duty for the existing security watch.
LP/OP should be assigned the air guard mission to listen for UAS.
1-13
References
ATP 3-01.8 Techniques for Combined Arms for Air Defense, 29 July 2016.
68 pages.
1-14
SIGMAN Camouflage SOP:
Chapter 2: How To
www.warfighting.us
How To
CAMOUFLAGE a Helmet
Purpose. To REDUCE the physical
signature (visual) of the helmet IOT
AVOID being observed and
targeted by the adversary.
Time
Equipment
Net, helmet band, zip ties, boot bands, and burlap strips. Camouflage net. Foliage.
Process
1. DRAPE a net over the helmet. Secure with a helmet band, zip ties, or boot bands.
ADD knotted burlap strips.
Or,
Or,
2-1
2. ADD natural camouflage to blend with your environment. Keep vegetation short. Long leaves
move too much. Cut vegetation, do NOT rip it up by the roots. See CUT Vegetation.
Notes
The shape of the helmet—its most
recognizable characteristic—must
be changed.
A combination of techniques,
camouflage netting plus boot
bands, is preferred. The net
obscures the shape of the helmet
and the boot bands hold vegetation.
2-2
The kevlar helmet has no radar
signature.
2-3
www.warfighting.us
2-4
How To
CAMOUFLAGE a Rifle
Purpose. To REDUCE the physical signature (visual) of the rifle IOT AVOID being observed and
targeted by the adversary.
Process
Weapons Painting SOP. CamPen, CA: 1st Marines, 1 Feb 2020. 48 pages.
Or,
2. WRAP boot bands around the stock and the hand guards. WRAP burlap strips.
ADD foliage in the field to BLEND with your surroundings.
The linear shape and black color of
the rifle—its most recognizable
characteristics—must be masked.
2-5
Cloth tape can break up the shape of the stock.
The radar signature of the metal rifle cannot be masked.
References
2-6
How To
CAMOUFLAGE Equipment
Purpose. To REDUCE the physical signature (visual) of the Marine IOT AVOID being observed and
targeted by the adversary.
Time
With a prepared assault and/or main pack, a Marine adds foliage in 10 minutes.
With a camouflage ghillie blanket, a Marine covers equipment in 10 minutes.
With prepared platforms, a Marine camouflages flak, boot tops, and sub-belt in 10 minutes.
Equipment
Tactical-colored bungee cords. Boot Bands. Foliage. 550 Cord. Camouflage ghillie blanket.
2. WEAVE a bungee cord through the MOLLE webbing on the top of the pack.
3. TIE pieces of “gutless” 550 cord into other pack webbing you want to camouflage.
4. ADD foliage in the field to blend with your environment. Tuck foliage under the bungees and
tie it with the 550 cord.
Or,
2-7
5. CARRY a camouflage ghillie blanket. SEE DEPLOY a Camouflage Ghillie Blanket.
Notes
550 CORD tie ins should be grouped in twos. One clump of vegetation should be tied into two 550
cord anchors to prevent excessive flapping. Burlap strips can be used instead of natural foliage.
MASK the shine on your equipment. Metal buckles and snaps can reflect light. Clip clips and zip
zippers silently.
AVOID staging packs in neat rows on the ground. Patterns are easily seen from the air.
A camouflage ghillie blanket is one of the best ways to camouflage a pack, a Marine, or a fighting
position. See CAMOUFLAGE a Fighting Position.
Vegetation should be collected from the local environment and periodically updated. See CUT
Vegetation.
1. WRAP shoulder straps of flak or chest-rig with boot bands or shock cord.
2. DON an extra set of boot bands outside of trousers, over the boot top.
3. WEAVE boot bands, bungees, or shock cord through belt pouches and flak pouches.
4. TUCK bundled vegetation into the elastic platforms. SEE CUT Vegetation.
2-8
Or,
5. DON a ghillie blanket after preparing with cut vegetation. See DEPLOY
a Camouflage Ghillie Blanket.
Notes
Use the RIGHT SIZE of vegetation for each platform. SEE CUT Vegetation.
Gutless 550 cord can be used to make vegetation anchors on gear webbing.
Notes on employment
This covers three of the four most distinguishable areas of the human silhouette—shoulders, waist
and ankles. For the head, see CAMOUFLAGE a Helmet.
2-9
TAILOR the level of vegetation used to the tactical situation. EXAMPLE: a long range foot patrol may
not need shin camouflage but a close-in ambush may.
The camouflage ghillie blanket provides maximum camouflage, but also maximum encumbrance. It
will snag on thick brush and rough terrain. TAILOR it to your mission.
2-10
How To
CUT Vegetation
Purpose. To REDUCE the physical signature (visual) of Marines and equipment IOT AVOID being
observed and targeted by the adversary.
Time. With a field knife, a Marine cuts vegetation in 5 minutes. With a prepared platform, a Marine
adds vegetation to the platform in 5 minutes.
Equipment
Field knife. Gloves. Local foliage source. Prepared platform: pack, helmet, boonie cover, flak jacket.
Process
Notes
2-11
CUT more than you think you need. This saves having to go back and re-forage for more.
Pack. USE long clumps of vegetation to cover the pack’s larger surface area.
Camouflage ghillie blanket. USE fist-sized clumps around the head and shoulders, longer clumps
down the back. Higher back clumps should point down. Lower back clumps should face up.
Plate carrier, chest-rig shoulder straps. USE long blundles to mask the shape of the shoulders and
obscure the chest.
Pouches. USE smaller bundles to avoid interference with access and movement.
2-12
How To
Time
In 5 minutes, a Marine deploys a camouflage ghillie blanket to conceal their silhouette, equipment, or
fighting position.
Equipment
1. PREPARE the blanket. It should be rolled up in a position that can be easily accessed and it
should have local vegetation already tied in..
2. UNROLL and DRAPE the blanket over the shoulders and pack like a cape.
3. SECURE the blanket by tying the shoulder ties and waist ties.
See BUILD a Camouflage Ghillie Blanket.
1. DROP your pack, ensuring that you have all essential gear on your person.
2-13
2. UNROLL and DRAPE the blanket over the pack.
4. HIDE shadows from the blanket by keeping the pack in defilade and close to the ground.
2. HIDE shadows from the blanket by keeping it low to the ground, using local foliage, and
staking the blanket to the deck.
Notes
Always use local vegetation with the camouflage ghillie blanket. The blanket is a baseline but
“veg is the edge.” See CUT Vegetation.
You are NOT invisible while wearing a camouflage ghillie blanket. The blanket is most effective when
you are prone, still, and silent.
When moving, the camouflage ghillie blanket must be secured tightly to the Marine to prevent
tell-tale movement and catching on terrain.
2-14
How To
Tactical-colored netting, black marker, tactical colored 550 cord (with the guts pulled out), burlap,
multi-tool / knife. Optional: fabric paints, fabric dyes, sliding toggle from main-pack repair kit.
Process
1. SIZE the netting. It should cover your head like a hood while falling just above the waist.
2. MARK the hood. Wearing the netting, have another Marine trace the outline of your head and
shoulders with a black marker.
3. TIE shoulder ties. TIE one 18-inch piece of gutless 550 cord to each shoulder of the hood.
These ties will hold the blanket to your shoulders.
4. TIE waist ties. TIE one 18-inch piece of gutless 550 cord to each of the lower corners of the
blanket. These ties will hold the blanket to your waist.
5. TIE foliage anchors. TIE a pair of 12-inch pieces of gutless 550 cord to the blanket, four
inches apart. Repeat this with a dozen or more pairs of 550 cord until the back of the blanket
has enough anchor points to hold a suitable amount of foliage. Prioritize anchors on the hood
and the top third of the blanket. The middle third and bottom third need less.
6. TIE burlap strips to the back of the blanket. Avoid patterns but prioritize the hood and the top
third of the blanket. The middle third and bottom third need less burlap.
2-15
On left, burlap and tie density are greatest on hood and top third of blanket, with less burlap on the middle and bottom third.
Close-up on right shows the shoulder ties with toggle.
Fabric paint and dyes can be used to add camouflage patterns to the blanket.
A sliding toggle can be used to connect the shoulder ties.
WASH and DRY the blanket. Getting the blanket wet helps weather it. A quick cycle in the dryer will
help gnarl and weather the burlap.
2-16
How To
CAMOUFLAGE a Bivouac
Purpose. To REDUCE the physical signature (visual, IR thermal, and radar) of the bivouac IOT
AVOID being acquired and targeted by the adversary.
Scope. Bivouac sleeping area only. See other sections for vehicles, TAAs, fighting positions, and
OP/LPs. For patrol base operations, see CAMOUFLAGE a Patrol Base.
Process
1. DISPERSE into multiple small elements. This is the most important step.
BE indistinguishable—unable to be identified as different—IOT avoid being targeted. Multiple
small bivouacs are better than one large one. DISPLACE often.
DISPERSE positions irregularly, NOT covered and aligned. AVOID rows of tents, packs,
pallets, or equipment. Patterns are easily seen from the air:
2. FIND a concealed site, off the main roads and away from junctions.
CONFORM to terrain. FIND low dead ground and micro-terrain, under trees, behind hills,
tucked into the shadows of buildings. In the city, bivouac inside a building.
STAGE packs under trees and in the shadows, NOT covered and aligned. COVER with
camouflage ghillie blankets. See CAMOUFLAGE Equipment.
2-17
TIE a length of 550 cord along the Spine of the A-frame. ATTACH irregular lengths of 550 cord to the Spine.
5. MINIMIZE movement.
2-18
7. PLAN to operate under UAS. Think overhead. Hills block ground visual, IR thermal, and radar
observation, but the biggest threat is overhead UAS. PLAN resupply events.
8. INSPECT your signature from the enemy’s point of view. USE binoculars, NVGs, thermal
scopes, and UAS during clearance patrols.
Notes
A bivouac near vehicles needs to cordon and mark the bivouac area. USE IR chemlites to maintain
light discipline and preserve night vision.
2-19
www.warfighting.us
2-20
How To
Process
1. DISPERSE into multiple small elements. This is the most important step.
BE indistinguishable IOT avoid being targeted. ASSUME you are being watched.
ESTABLISH irregularly-spaced positions, NOT linear positions.
2. FIND a concealed site. The mission—the sector of fire—dictates the position. CONFORM to
terrain. AVOID silhouettes. Positions in open desert terrain have few options.
4. CAMOUFLAGE your position. BLEND with your surroundings. Every position needs overhead
concealment. COVER your position with a camouflage ghillie blanket, camouflage net, woven
mat, or a MARPAT tarp. ADD foliage to blend with your environment.
2-21
All of these coverings are best when laid on top of a flat-top frame of deadfall branches lashed
to corner tripods.
Experiments at SOI-W concluded that the camouflage ghillie blanket is the most effective
camouflage against UAS. A camouflage net is second, followed by a locally-constructed
woven mat. The MARPAT tarp is the least effective covering due to its square and shiny
appearance, distinctive sag, and difficulty in adding foliage. A thermal blanket below the
concealment layer disrupts the IR thermal signature.
PICK a position with natural frontal cover to AVOID building a parapet of newly-dug earth.
5. MINIMIZE movement.
6. POST an air guard. LP/OPs should be assigned the air guard mission to listen for UAS.
Critical machinegun (MG) and anti-armor (AA) fighting positions must be well-camouflaged.
In the illustration, the MG position (a) is protected by a squad. The MG primary sector (b) is defined by
an FPL across the company front. A secondary MG sector (c) protects the left flank. A squad
automatic rifle FPL (d) is laid to parallel the MG.
The vital MG position and its protective squad is a single high-priority position and must be
well-camouflaged from enemy observation and protected from enemy fires.
All positions need overhead concealment: a flat-top frame of deadfall branches lashed to corner
tripods. Beneath the poncho and leaves, a thermal blanket disrupts IR thermal signature.
2-22
Notes on Sandbags. Synthetic sandbags “shine like light bulbs” and are easily seen from the air.
SOI-W recommends smearing sandbags with mud.
Battle position preparations are difficult to mask. Uncontrolled noise, people, activities, equipment,
materials, vehicles, and possible engineer support can create an overwhelming signature.
Unit leaders must discipline the process to avoid being targeted. OCCUPY at night. STAGGER
activities to reduce noise and congestion. CAMOUFLAGE preparations, positions, and supplies.
AVOID excessive clearing. AVOID creating a visible trail to your position. CAMOUFLAGE the CP.
CONCEAL spoil. REMOVE trash and dunnage. CONTROL vehicle movement.
CONTROL fires and stoves. Cook in dead ground or under trees, and only during daylight.
CAMOUFLAGE RES positions. SELECT a concealed CATK position and CATK route.
Notes
PLAN to operate under UAS. Think overhead. Hills block visual, thermal, and radar observation, but
the biggest threat is overhead UAS. PLAN operations at critical times. MINIMIZE logistics
2-23
requirements. PLAN resupply events.
INSPECT your signature from the enemy’s point of view. USE binoculars, NVGs, thermal scopes, and
UAS.
Hasty positions, skirmishers trenches, need overhead concealment early in the process.
Units need TTPs to CAMOUFLAGE a bunker, CAMOUFLAGE a tower, CAMOUFLAGE a building,
and CAMOUFLAGE a mortar position.
Low, small, and slow UAS are flown by the adversary from nearby clearings and hilltops. Aggressive
patrolling of key terrain can push adversary UAS operators away from your unit.
References
Walker Mills. AAR from 1st Battalion, 4th Marines MCCRE Regarding Small
Unmanned Aerial Systems. CamPen, CA: 2nd Battalion, 1st Marines, 30 Jun 2018.
“An entrenched defense is no longer tenable... against an enemy… with UAS and
long-range fires. A defense… needs to prioritize concealment… Digging a… defense
is a sure way to get...targeted. The (adversary) was able to identify all the elements…
more accurately when they were in the defense than at any other time.”
NAVMC 3500.44D Infantry T&R Manual, 7 May 2020.
The SAFESOC priority of work, Figure 4-2 on page 81, puts camouflage last. This is
based on an outdated assumption that firepower negates the risk of discovery by the
enemy. This is no longer true and therefore the priority of work must be changed:
camouflage is second priority after security.
2-24
How To
CAMOUFLAGE an OP/LP
Purpose. To REDUCE the physical signature (visual, IR thermal) of the OP/LP IOT AVOID being
observed and targeted by the adversary.
Process
1. BUILD a flat-top frame to avoid overhead observation of the OP. All positions need overhead
concealment: a flat-top frame of deadfall branches lashed to corner tripods. Beneath the
poncho and leaves, a thermal blanket disrupts IR thermal signature.
2-25
LEAVE gaps for two observation windows.
OP view from left observation window. OP view from right observation window.
2-26
View from behind the linear barrier. Detail of tripod. View from behind the linear barrier.
PAS-28 thermal view of OP at 15m. A head is visible. Plexi-glass masks thermal signature of head.
4. BUILD a v-shaped barrier for flank positions. USE three or four tripods.
2-27
V-shaped barrier.
View from behind v-shaped barrier. View of v-shaped barrier from enemy point of view.
OP detail views of overhead concealment: flat-top frame of deadfall branches lashed to corner tripods.
2-28
How To
CAMOUFLAGE a Vehicle
Purpose. To REDUCE the physical
signature (visual, IR thermal, and
radar) of the vehicle IOT AVOID
being observed and targeted by the
adversary.
Time. After picking a position, two Marines should camouflage a vehicle in 15 minutes.
Equipment. LCSS or ULCANS camouflage netting system with tent pins. Styrofoam dunnage.
Process
1. DISPERSE into multiple small elements. This is the most important step.
BE indistinguishable—unable to be identified as different—IOT avoid being targeted.
ASSUME you are being watched. DISPERSE vehicles irregularly. DISPLACE often.
CONFORM to terrain.
FIND low dead ground and
micro-terrain, behind hills,
tucked against the shadows
of buildings, or under trees.
In the city, park inside a
building.
POSITION the net diagonally, offset from the long axis of the vehicle, with more material on
the shady side of the vehicle. BLEND with your environment. Vehicles in open desert terrain
often have few options.
2-29
4. LIFT the net with support poles to create an irregular shape. The shape of the vehicle—its
most recognizable characteristic—must be changed.
If thermals sensors are a threat, get two feet of clearance off of all metal surfaces. Use
styrofoam dunnage to prop the netting off the surface of the vehicle. Styrofoam dunnage can
be glued/taped down to the surface of the vehicle, in order to speed up camouflage efforts and
keep netting off of hot areas.
5. PIN the net down with tent pins, flush and tight to the ground.
Maximize the slope.
Avoid vertical sides.
Camouflage netting provides concealment where none is available. It is portable, quick to set up, and
multispectral - masking vehicles from visual, IR thermal, and radar sensors.
The older Lightweight Camouflage Screen Systems (LCSS), has been replaced by the newer Ultra
Lightweight Camouflage Net Systems (ULCANS). There are three colors. Class 1 is Woodland, Class
2 is Desert, and Class 3 is Snow. Each is reversible, with a different shade on each side. Additionally,
nets are typed as either radar scattering or radar transparent (for use with radar vehicles), but the
differences are invisible. Each net is labelled with Class and Type.
2-30
Camouflage netting comes in two shapes: Hexagon and diamond.
Join one hex and two diamonds (48 x 28 feet) to cover a tactical vehicle.
Notes
PLAN to operate under UAS. Think overhead. Hills block visual, thermal, and radar observation, but
the biggest threat is overhead UAS. Use a thermal blanket to disrupt your heat signature against
enemy thermal sights. Use the right color camouflage netting to blend with your environment.
INSPECT your signature from the enemy’s point of view: binoculars, NVGs, thermal scopes, UAS.
One hex (28 x 32 feet) covers a generator or a GP Small Tent. Two hex and two diamonds (56 by 48
feet) covers a truck. Three hex and three diamonds (56 x 64 feet) covers larger vehicles or a GP
Medium tent. See TM 5-1080-250-12&P, pp 1-5.
2-31
References
2-32
How To
CAMOUFLAGE a Convoy
Purpose. To REDUCE the physical signature (visual, IR thermal, and radar) of the convoy IOT
AVOID being observed and targeted by the adversary.
Process to DRIVE
1. DISPERSE vehicles irregularly along the route. This is the most important step.
DRIVE in small serials of twelve or less vehicles.
BE indistinguishable—unable to be identified as different—IOT avoid being targeted.
ASSUME you are being watched.
2. DRIVE on concealed routes. CONFORM to terrain. When driving cross-country, parallel fence
lines, fields, and natural features. Do NOT cut diagonally across open terrain.
3. DRIVE at night. DRIVE with blackout lights and NVGs. KNOW the hours of moonrise (MR) and
moonset (MS), and the percent of lunar illumination.
Process to STOP
Process to PLAN
2. PLAN concealed routes. PLAN concealed stops, concealed re-fueling, and concealed TAAs.
2-33
3. PLAN to OPERATE at night.
7. PLAN rally points for separated vehicle/serials. Rally points should be areas where multiple
vehicles can be easily camouflaged (i.e., wood lots, towns, hilly areas, etc.)
Notes
2-34
How To
CAMOUFLAGE a CP
Purpose. To REDUCE the physical signature (visual, IR thermal, and radar) of the CP IOT AVOID
being observed and targeted by the adversary.
Process
1. DISPERSE into multiple small elements. This is the most important step.
BE indistinguishable—unable to be identified as different—IOT avoid being targeted.
ASSUME you are being watched. DISPLACE often.
2. FIND a concealed site. Select a site unimportant to the adversary, off the main roads. AVOID
road junctions.
2-35
6. POST an air guard.
7. PLAN to operate under UAS. Think overhead. Hills block visual, thermal, and radar
observation, but the biggest threat is overhead UAS. PLAN concealed routes and positions.
PLAN resupply events.
8. INSPECT your signature from the enemy’s point of view. USE binoculars, NVGs, thermal
scopes, and UAS.
COUNTER adversary HUMINT, OSINT, and ELINT efforts. This information cues ISR
platforms. Reduce the signature of your CP so that the adversary does NOT prioritize his ISR
assets against you.
See CAMOUFLAGE a Vehicle. One hex (28 x 32 feet) covers a generator or a GP small tent. Three
hex and three diamonds (56 x 64 feet) cover a GP Medium tent. See TM 5-1080-250-12&P, pp 1-5.
The contained shadow is the biggest error made with camouflage netting. Pin the net flush and tight to
the ground. Avoid creating a dark triangular gap that can easily be seen from the air.
Notes
Use the right color camouflage netting to blend with your environment.
2-36
Notes on Base Camps
Base camps, ports, warehouses,
and airfields are easily visible from
the air. Infantry units are usually
tenant organizations. The camp
commandant is responsible for base
camp SIGMAN and camouflage
discipline.
2-37
www.warfighting.us
2-38
How To
CAMOUFLAGE a TAA
Purpose. To REDUCE the physical signature (visual, IR thermal, and radar) of the TAA IOT AVOID
being observed and targeted by the adversary.
Equipment. Each Marine and each vehicle has the camouflage equipment they need.
Process
1. DISPERSE into multiple small elements. This is the most important step.
BE indistinguishable—unable to be identified as different—IOT avoid being targeted.
ASSUME you are being watched.
DISPERSE vehicles irregularly within the site.
DISPLACE often.
2-39
5. MINIMIZE movement. MINIMIZE radio for EMCON.
ESTABLISH routes in and out to reduce track signatures. CONTROL traffic.
7. PLAN to operate under UAS. Think overhead. Hills block visual, thermal, and radar
observation, but the biggest threat is overhead UAS. PLAN concealed routes and positions.
PLAN operations at critical times. MINIMIZE logistics requirements. PLAN resupply events.
8. INSPECT your signature from the enemy’s point of view. USE binoculars, NVGs, thermal
scopes, and UAS.
Missile, rocket, artillery, and mortar blast effects differ by weapon, size, and munition. HE, DPICM,
and fuel-air explosive blasts are different. Generally, however, increasing vehicle dispersion from two
to three vehicle lengths, reduces the number of vehicles in the kill zone by almost half.
Vehicle dispersion. With 30 foot dispersion, 28 HMMWVs fit on a football field. With 45 foot dispersion,
15 HMMWVs fit. Notes: Blast effects are not circular. HMMWV is 15 feet long (4.6 m).
2-40
Notes on Vehicle Tracks
Vehicle tracks, easily seen from the air, are a dead giveaway for a TAA.
Any diagonal tracks, across a field or cutting through an intersection, are especially noticeable.
Looping tracks, at a turnaround point or refueling area, are especially noticeable.
The TAA site plan should establish a new track along a linear feature with a marked turnoff point.
RIGHT: Single track with inconspicuous turnoff into TAA. WRONG: Tracks clearly point to a concealed TAA.
Vehicle tracks, easily seen from the air. TAA: NO site plan, NO traffic control. Same vehicles, parked well, less tracks.
2-41
www.warfighting.us
2-42
SIGMAN Camouflage SOP:
Chapter 3: Train
www.warfighting.us
Train
Training
1. Camouflage standards should be practiced during all training and all exercises, in all
environments, regardless of the primary purpose of the training.
Unit leaders can use time during larger exercises to practice drills and evaluate their own unit’s
camouflage efforts.
3-1
UNITED STATES MARINE CORPS
2nd Battalion, 5th Marines
Camp Pendleton, CA 92055
28 Aug 2020
1. Situation. The Bn SOP has been updated with multiple SIGMAN camouflage drills and standards. All Marines and
units need to be trained to the established standards.
2. Mission. On 08-10 Sep, 2/5 conducts operations and applies SOP standards IOT evaluate unit camouflage skills.
3. Execution
a. CONOPS. Over three days, each unit executes multiple FRAGOs, all while under adversary ground and
air (UAS) observation and probing attacks. From TAA BLUE, units move during the day and night,
occupy a BP, conduct security patrols, resupply, and then retrograde.
b. Tasks
(1) Units. OCCUPY TAA BLUE NLT 1000 TUE 8 SEP 2020. EXECUTE operations IAW
FRAGOs. TRAIN on SIGMAN Camouflage SOP skills.
(2) OPFOR. COLLECT on Bn units using both ground and air (UAS) assets. Call for fire.
CONDUCT probing attacks. PHOTOGRAPH and report on unit sizes and locations. ASSESS
unit training levels. BRIEF results at AAR.
(3) EXCON. CONTROL the exercise. ASSESS casualties. CONDUCT AAR in order to improve
Bn SIGMAN Camouflage SOP and procedures.
c. Coordinating Instructions
3-2
(1) Task Organization
Units (8): E, F, G, 81, HMG, COC, BAS, Log Train.
OPFOR: XO, S-2, SSP, AA Platoon, UAS, and four company 1stSgt.
EXCON is OpsO and a det from the AA Platoon.
(2) Schedule:
Time Units OPFOR EXCON
Tue 1000 OCCUPY TAA BLUE TAA RED TAA RED
Tue 1100 FRAGO 01: Movement to Contact Collect
Tue 1900 FRAGO 02: Night Infiltration Operation Collect
Wed 0800 FRAGO 03: ESTABLISH BP Collect / Probe
Wed 1900 FRAGO 04: Night Security Operation Collect / Probe
Thu 0800 FRAGO 05: Movement to Garrison Prepare AAR Prepare AAR
Thu 1300 Classroom: AAR for all Battalion Leaders AAR Run AAR
(3) All FRAGOs will be issued in the field. The OPFOR will NOT see the FRAGOs.
(4) Range control coordination, airspace coordination, and safety vehicle requirements will be
executed by EXCON.
(6) EW and EMCON procedures will NOT be evaluated. OPFOR will NOT collect on technical
(EMCON) signatures.
a. Encl (1) lists pyrotechnics and blank ammunition requirements. S-4 will issue ammunition in TAA BLUE
NLT 1100 Tue 8 Sep 20.
b. S-1 will process daily PERSTATREPs and other required reporting IAW SOP.
c. S-4 Log Train will resupply units each day as a tactical evolution IAW RRP SOP. No hot chow.
5. Communication and Signals. S-6 will establish an EXCON and an OPFOR net. All Battalion units will operate on
standard nets IAW Bn SOP.
P.A. BEEKMAN
By dir
3-3
www.warfighting.us
3-4
Train
Marine Corps Infantry Camouflage Standards. NAVMC 3500.44D Infantry Training and Readiness
Manual, 7 May 2020, contains only two camouflage tasks:
Marine Corps Doctrine. The following manuals emphasise the importance of camouflage and
provide camouflage instructions: MCTP 3-01A Scouting and Patrolling, MCRP 3-10A.2 Infantry
Company Operations, MCIP 3-10A.4i Marine Rifle Squad, MCTP 3-01E Sniping, and MCTP 3-34C
Survivability Operations.
3-5
Recommended Camouflage Individual Training Standards
Responsibilities. During each phase of an amphibious operation or a raid the responsibility for both
the adversary threat and signature management is assigned to a specific unit or command. It is
important for signature management responsibility to be centralized because a large unit or task
force’s signature management is only as good as its weakest link. Military deception needs to be
3-6
integrated with signature management. Commands can delegate signature management
responsibility or assign specific individuals to oversee signature management. This does not absolve
individuals and smaller units of the responsibility to reduce their signature.
The responsibility for both the adversary threat and signature management shifts during an operation
and the specific camouflage and signature management actions Marines will need to take will vary
depending on the environment: urban, jungle, wooded, or desert.
UAS, Aircraft
INSERT by surface craft undetected Mines, patrol craft CATF
Adversary units
UAS, aircraft
MOVE on foot toward the objective undetected Reconnaissance, IDF Unit of Action
Adversary units
UAS, aircraft
CONVOY by vehicle toward objective
Reconnaissance, IDF Unit of Action
undetected
Adversary units
UAS, aircraft
Actions on the objective Reconnaissance, IDF Unit of Action
Adversary units
UAS, aircraft
MOVE on foot toward the LZ undetected Reconnaissance, IDF Unit of Action
Adversary units
UAS, Aircraft
EXTRACT by surface craft undetected Mines, patrol craft CATF
Adversary units
3-7
Tasks. During combat operations ashore, the responsibility for signature management is generally
with the unit of action. However, expeditionary bases with multiple units are a signature management
challenge. Camouflage actions differ in each environment: urban, jungle, wooded, or desert.
Adversary SIGMAN
Action
Threat Responsibility
UAS, aircraft
CONVOY by vehicle within the AO undetected Reconnaissance, IDF Unit of Action
Adversary units
UAS, aircraft
OCCUPY an AA undetected Reconnaissance, IDF Unit of Action
Adversary units
UAS, aircraft
OPERATE from an established base camp Reconnaissance, IDF Camp CO
Adversary units
UAS, aircraft
MOVE on foot within the AO Reconnaissance, IDF Unit of Action
Adversary units
UAS, aircraft
OPERATE from a patrol base undetected Reconnaissance, IDF Unit of Action
Adversary units
3-8
Train
Condition. The unit has been stationary for at least two hours. The unit is camouflaged.
Standard. The unit cannot be seen or heard by a ground or air adversary 1000m away.
Equipment. “Camouflage Inspection Checklist,” binoculars, NVGs, PAS-28 thermal scope, or UAS.
Process
Notes
Unit leaders should appoint a SNCO to collect own-force signature. Fieldcraft is SNCO expertise. The
observer should understand adversary ISR capabilities—satellites, aviation, UAS, and ground
sensors.
The observer should envision the unit signature from the air: lines, lights, vehicles, tracks, fighting
positions, spoil, debris, pallets, and supplies.
References
3-9
Camouflage Inspection Checklist Date:
Purpose. To inspect a stationary unit that has been in an TAA or BP for more than two hours. Unit:
Scope. NOT a base camp. NOT a movement. NOT a convoy. Marks. All “YES” is best. Initials:
1. Leadership. Do unit leaders inspect camouflage every day IAW SOP? Y N TBD
Is an air guard, who knows the warning procedure, on watch for aircraft and UAS?
3. Vehicles. Is every vehicle off, covered with a camouflage net, flush to the ground?
Is every vehicle dispersed, irregularly, at least three vehicle lengths from the next?
Tents. Is every CP tent covered with a camouflage net, flush to the ground?
Tents. Are all supplies or pallets covered with a camouflage net, flush to the ground?
Or buildings. Do supply buildings look ordinary so they will NOT be targeted?
6. Unit. Is the unit’s overall position camouflaged well enough NOT to be targeted?
Have piles of earth (spoil) been masked so that they are NOT visible from the air?
Have vehicle tracks been masked so they are NOT visible from the air?
Was light discipline good last night? Were lights from vehicles and the CP masked?
Is trash discipline good? Have trash bags, dunnage, and debris been hidden?
Summary:
3-10
SIGMAN Camouflage SOP:
Chapter 4: Understand
www.warfighting.us
Understand
Adversary UAS
Purpose. To find information on adversary UAS.
Process
3. SEARCH the web for evolving UAS capabilities and UAS imagery.
See the TRADOC ODIN Worldwide Equipment Guide.
4. UNDERSTAND UAS terms. UAS groups 1 through 5 are defined by the Joint UAS COE
CONOPS V1.5, 2008. Low, slow, and small (LSS) UAS, which include micro- and mini-UAS
are defined by ATP 3-01.81 C-UAS Techniques, 13 Apr 2017.
4-1
The Drone Databook. By Dan Gettinger. Annandale-on-Hudson, NY: Bard
College, 2019.
dronecenter.bard.edu
Use of UAS by the world’s militaries has doubled since 2010. Gettinger lists
over 100 separate systems used by over 100 countries.
The Islamic State and Drones: Supply, Scale, and Future Threats. By Don
Rassler. West Point, NY: U.S. Military Academy, 2018. www.ctc.usmc.edu
Many insurgent groups may replicate what ISIS did to acquire, arm, and
employ commercial UAS.
6. UNDERSTAND adversary UAS TTPs. Because offset position reporting is difficult for small
UAS, Russian practice is to fly directly over the target to acquire an accurate target position.
1 Aug 2020
4-2
Understand
Adversary Satellites
Purpose. To find information on adversary satellites.
Process
NASIC (U.S. Air Force) provides intelligence on foreign air and space forces.
6. UNDERSTAND satellite TTPs. When are adversary satellites collecting on your unit in your
AO? When is your window of vulnerability? What types of units, ships, facilities, and equipment
are most vulnerable to satellite collection? What sensors are being used? How can those
sensors be mitigated?
4-3
7. UNDERSTAND U.S. signatures that are vulnerable to adversary satellites.
1 Aug 2020
4-4
Understand
Adversary Missiles
Purpose. To find information on adversary missiles.
Process
4. UNDERSTAND missile terms. What is the difference between ballistic missiles and cruise
missiles? Why are ballistic missiles classified by range, but cruise missiles classified by type of
target?
4-5
6. UNDERSTAND adversary missile TTPs.
1 Aug 2020
4-6
Understand
Process
1. ASK the S-2 for adversary rocket, artillery, and mortar intelligence in your AO.
On 14 July 2014, two mechanized battalions of the Ukrainian Army, in an assembly area near
Zelenopillya, Ukraine, were almost completely destroyed by a Russian rocket barrage.
The attack was conducted by UAS. The Russian rocket launchers, firing from inside Russian
territory, were Tornado-G 122mm MLRS, an upgrade to the BM-21. The barrage included
top-down anti-tank DPICM and thermobaric fuel-air explosives.
Over 100 other Russian rocket and artillery attacks followed during July and August 2014.
4-7
4. UNDERSTAND rocket, artillery, and mortar terms.
BM-21 122mm 20 km
BM-27 220mm 35 km
BM-30 300mm 90 km
9A52 Tornado is a new MLRS. It is separate from the Tornado upgrades to the BM-21,
BM-27, and BM-30. The Tornado 9A53-G is the upgrade to the BM-21. Range is 40 km.
Common Russian Self-Propelled (SP) Artillery Nomenclature
2S1 122mm 15 km
2S3 152mm 18 km
D-30 122mm 15 km
2B11 82mm 7 km
5. UNDERSTAND rocket, artillery, and mortar proliferation. What adversaries have acquired
what weapons from what countries?
4-8
Russian BM-30 Smerch (9A52-2)
6. UNDERSTAND rocket, artillery, and mortar TTPs. Russia is fielding one UAS company to
each brigade to support multiple artillery battalions.
Direct overhead flight is the primary means of calling for fire with UAS at
night: “Since terrain association with a thermal imager would be difficult… and
the risk of the UAS being shot down at night is… reduced, it is likely the UAS
operator uses the ‘fly-over-the-target’ method to fix the target.”
1 Aug 2020
4-9
www.warfighting.us
4-10
Understand
Process
NASIC (U.S. Air Force) provides intelligence on foreign air and space forces.
ONI (U.S. Navy) provides intelligence on foreign naval forces.
Russia’s Black Sea Fleet: Toward a Multiregional Force. By Igor Delanoe.
Arlington, VA: CNA, 5 Jun 2019. 36 pages.
4-11
1 Aug 2020
4-12
Understand
Process
FIND — An EM signal is detected and cues UAS. The FIND step can be done by any ISR:
ground reconnaissance, SIGINT, HUMINT, ELINT, or MASINT.
TRACK — The UAS tracks the target location if the target is moving.
TARGET — The adversary Tornado-G battery calculates range and targeting data.
ENGAGE — The adversary Tornado-G battery fires rocket barrages to destroy the target.
There are many combinations of equipment and units that can execute a kill chain.
4-13
Table. Disruption: ISR platforms vs. types of targets.
Light discipline disrupts visual ISR. The human eye can see a campfire at 8 km, and vehicle lights at 20 km.
Heat discipline disrupts IR thermal ISR.
Noise discipline disrupts direct observation (listening) by ground reconnaissance units.
EMCON disrupts adversary SIGINT collection efforts.
NVGs are image intensifiers. They take existing light—from the stars, the moon, and from
manmade illumination—and magnify it.
To disrupt adversary NVGs, PLAN operations at critical times. KNOW the hours of moonrise
(MR) and moonset (MS), and the percent of lunar illumination.
A 20% moon, positioned at 30 degrees above the horizon provides 0.022 lux. Less than this
amount of light is called low light. A full moon is ten times brighter than a new moon.
To disrupt adversary IR thermal sensors, PLAN operations at critical times. KNOW the hours
of BMNT, sunrise (SR), EENT and sunset (SS).
4-14
Thermal crossover times differ—because each piece of equipment heats and cools at different
rates—but they generally occur near sunrise and sunset.
A moving target indicator (MTI) picks up metal. Vehicles in the open can be detected by air or
ground MTI at 20 kilometers. Convoys moving on covered routes can disrupt their metal
signature. Camouflage netting, when kept two feet off the metal surface, can disrupt the radar
signatures of vehicles. Conex boxes, infantry weapons, and metal ammunition cans can be
vulnerable to air and ground radars.
1 Aug 2020
4-15
www.warfighting.us
4-16
Understand
Process
The Joint Force Commander (JFC) is responsible for AMD. The JFC appoints an Area Air
Defense Commander (AADC), who establishes an integrated air defense system (IADS) and
writes the Area Air Defense Plan (AADP). The Joint Force Air Component Commander
(JFACC) executes the AADP. Only the AADC can delegate engagement authority to tactical
units to shoot at adversary aircraft and missiles.
Air and Missile Defense (AMD) consists of Air Defense (AD) - against aircraft, UAS, and
cruise missiles - and Ballistic Missile Defense (BMD).
JP 3-01 Countering Air and Missile Threats, 2 May 2018. 169 pages.
Defines joint terms for AMD. Describes key roles in the AMD command and
control structure. Discusses offensive and defensive AMD planning,
homeland security, and global missile defense.
ATP 3-01.15 / MCTP 10-10B AMD: Multi-Service TTPs for Air and Missile
Defense, 14 Mar 2019. 188 pages.
A comprehensive source for Joint and service AMD equipment, C2, and
doctrine, with a separate chapter for each service. JIPOE for AMD, UAS
challenges, planning checklists, and an AADP template.
In the Navy’s Composite Warfare Commander (CWC) construct, the Air Missile Defense
Commander (AMDC) defends the force against airborne weapons launched from aircraft,
4-17
ships, submarines, and land-based sites. The Ballistic Missile Defense Commander (BMDC)
defends the force from ballistic missiles.
NTTP 3-01.11 Maritime Air and Missile Defense Planning, 1 Apr 2015.
The Navy’s Aegis weapons system tracks and engages incoming missiles. Aegis integrates air
and missile defense weapons, as well as ASW torpedoes and Tomahawk LACM.
The ACE protects the MAGTF. The ACE is not expected to contribute to the Joint AADP.
Antiair warfare, primarily conducted by aircraft, is one of the six functions of Marine aviation.
Marine LAAD units, with AD weapons but no radar, provide local air defense.
ATP 3-01.8 Techniques for Combined Arms for Air Defense, 29 Jul 2016.
68 pages.
1 Aug 2020
4-18
SIGMAN Camouflage SOP:
Chapter 5: Reference
www.warfighting.us
Reference
Glossary
Purpose. To collect standard definitions of SIGMAN and camouflage terms.
A2/AD — Anti-access and area denial. An imprecise term banned by the CNO in 2016.
A2 (antiaccess) — Action, activity, or capability, usually long-range, designed to prevent an advancing
enemy force from entering an operational area (DOD Dictionary, 1 Jan 2020).
AD (air defense) — Defensive measures designed to destroy attacking enemy aircraft or aerodynamic missiles,
or to nullify or reduce the effectiveness of such attack (DOD Dictionary, 1 Jan 2020).
active air defense. REMOVED from JP 3-01 Countering Air and Missile Threats and DOD Dictionary.
passive air defense. REMOVED from JP 3-01 Countering Air and Missile Threats and DOD Dictionary.
ADWC (air defense warning condition) — An air defense warning given in the form of a color code
corresponding to the degree of air raid probability with yellow standing for when an attack by hostile aircraft or
missiles is probable; red for when an attack by hostile aircraft or missiles is imminent or is in progress; and white
for when an attack by hostile aircraft or missiles is improbable (DOD Dictionary, 1 Jan 2020).
AMD (air and missile defense) — Direct [active and passive] defensive actions taken to destroy, nullify, or
reduce the effectiveness of hostile air and ballistic missile threats against friendly forces and assets (DOD
Dictionary, 1 Jan 2020).
ascent phase — That portion of the flight of a ballistic missile or space vehicle that begins after powered flight
and ends just prior to apogee (DOD Dictionary, 1 Jan 2020).
BM (ballistic missile) — Any missile that does not rely upon aerodynamic surfaces to produce lift and
consequently follows a ballistic trajectory when thrust is terminated (DOD Dictionary, 1 Jan 2020). See:
5-1
BMNT (begin morning nautical twilight) — The start of the period where, in good conditions and in the absence
of other illumination, the sun is 12 degrees below the eastern horizon and enough light is available to identify the
general outlines of ground objects and conduct limited military operations (DOD Dictionary, 1 Jan 2020) (This
definition should specify the “center of the sun.” The term “first light” is NOT used and has been dropped from
the DOD Dictionary).
BP (battle position) — 1. In ground operations, a defensive location oriented on an enemy avenue of approach
from which a unit may defend. 2. In air operations, an airspace coordination area containing firing points for
attack helicopters (MCRP 1-10.2 Marine Corps Supplement, 31 May 2018).
battle drill — A critical collective action or task performed by a platoon or smaller element without the
application of a deliberate decision-making process, initiated on cue, accomplished with minimal leader orders,
and performed to standard throughout like units (MCRP 1-10.2 Marine Corps Supplement t, 31 May 2018).
CM (cruise missile) — A guided and powered missile that flies at constant speed for the majority of its route and
relies upon aerodynamic forces for lift (DOD Dictionary, 1 Jan 2020). See:
CRBM (close-range ballistic missile) — A land-based ballistic missile with a range capability up to 300 nautical
miles (DOD Dictionary, 1 Jan 2020).
camouflage discipline
concealment — The protection from observation or surveillance (MCRP 1-10.2 Marine Corps Supplement, 31
May 2018) (NO DOD definition).
cover — 4. Protection from the effects of direct and indirect fire. It can be provided by ditches, caves, river
banks, folds in the ground, shell craters, buildings, walls, and embankments (MCRP 1-10.2 Marine Corps
Supplement, 31 May 2018) (NO DOD definition).
5-2
dead ground — Terrain not visible to the enemy and protected from enemy direct fires.
defilade — 1. Protection from hostile observation and fire provided by an obstacle such as a hill, ridge, or bank.
2. A vertical distance by which a position is concealed from enemy observation. 3. To shield from enemy fire or
observation by using natural or artificial obstacles (DOD Dictionary, 1 Jan 2020).
dispersal — Relocation of forces for the purpose of increasing survivability (DOD Dictionary, 1 Jan 2020).
dispersion — 1. The spreading or separating of troops, material, establishments, or activities, which are
usually concentrated in limited areas to reduce vulnerability (DOD Dictionary, 1 Jan 2020).
disrupt — 1. To integrate fires and obstacles to break apart an enemy’s formation and tempo, interrupt the
enemy’s timetable, or cause premature commitment or the piecemealing of enemy forces. 2. To preclude the
efficient interaction of enemy combat or combat support systems (MCRP 1-10.2 Marine Corps Supplement, 31
May 2018) (NO DOD definition).
EENT (end evening nautical twilight) — The point in time when the sun has dropped 12 degrees below the
western horizon, and is the instant of last available daylight for the visual control of limited military operations.
(DOD Dictionary, 1 Jan 2020) (This definition should specify the “center of the sun”).
engage — 1. In air and missile defense, a fire control order used to direct or authorize units and/or weapon
systems to attack a designated target. 2. To bring the enemy under fire (DOD Dictionary, 1 Jan 2020).
F2T2EA — find, fix, track, target, engage, and assess (DOD Dictionary, 1 Jan 2020).
FLIR (forward-looking infrared) — An airborne, electro-optical, thermal imaging device that detects far-infrared
energy, converts the energy into an electronic signal, and provides a visible image for day or night viewing (DOD
Dictionary, 1 Jan 2020).
friendly — A contact positively identified as a friend using identification, friend or foe and other techniques
(DOD Dictionary, 1 Jan 2020).
guided missile — An unmanned vehicle moving above the surface of the Earth whose trajectory or flight path is
capable of being altered by an external or internal mechanism (DOD Dictionary, 1 Jan 2020).
ICBM (intercontinental ballistic missile) — A long-range ballistic missile with a range capability greater than
3,000 nautical miles (DOD Dictionary, 1 Jan 2020).
IFPC (indirect fire protection capability) — IFPC Increment 2-Intercept (IFPC Inc 2-I) is a mobile, ground-based
weapon system designed to acquire, track, engage and defeat Unmanned Aircraft Systems (UAS), Cruise
Missiles (CM) and Rockets, Artillery and Mortars (RAM).
IRBM (intermediate-range ballistic missile) — A ballistic missile with a range capability from 1,500 to 3,000
nautical miles (DOD Dictionary, 1 Jan 2020).
ISR — intelligence, surveillance, and reconnaissance — 1. An integrated operations and intelligence activity that
synchronizes and integrates the planning and operation of sensors, assets, and processing, exploitation, and
dissemination systems in direct support of current and future operations. 2. The organizations or assets
conducting such activities (DOD Dictionary, 1 Jan 2020).
kill chain — In dynamic targeting, the steps and procedures involved to find, fix, track, target, engage, and
assess (F2T2EA) a target (JP 3-09 Joint Fire Support, 10 Apr 2019)(NO DOD or USMC definition).
5-3
LCSS — lightweight camouflage screen system (MCRP 1-10.2 Marine Corps Supplement, 31 May 2018).
low light — Light level less than 0.0022 lux. Other than low light is light level greater than or equal to 0.0022 lux
(CNAF M-3710.7 NATOPS, 5 May 2016).
LLL (low light level) — < 0.0022 lux (NO DOD or USMC definition).
HLL (high light level) — > 0.0022 lux (NO DOD or USMC definition).
LSS — low, slow, small UAS (ATP 3-01.81 C-UAS Techniques, 13 Apr 2017).
lunar illumination — Given in percentage of the actual lunar disk visible at midnight of each given day (MCRP
2-10.6 MAGTF Meteorological and Oceanographic Support, 4 Apr 2018) (Lunar illumination is reduced by cloud
cover and weather. Lunar illumination is NOT the percentage of illuminated hours of a given night. A full moon
below the horizon provides zero illumination).
lux — Luminous flux per unit area, measured as one lumen per square meter (SI). Sunrise is approximately 400
lux (U.S. Naval Observatory: https://aa.usno.navy.mil).
MD (missile defense) — Defensive measures designed to destroy attacking enemy missiles, or to nullify or
reduce the effectiveness of such attack (DOD Dictionary, 1 Jan 2020).
micro-terrain — Small folds in the ground that provide protection from observation and enemy fire (NO DOD or
USMC definition).
MRBM (medium-range ballistic missile) — A ballistic missile with a range capability from about 600 to 1,500
nautical miles (DOD Dictionary, 1 Jan 2020).
MR (moonrise) — The instant when the upper edge of the moon appears on the sea-level horizon (MCRP
2-10.6 MAGTF Meteorological and Oceanographic Support, 4 Apr 2018).
MS (moonset) — The instant when the upper edge of the moon disappears below the sea-level horizon (MCRP
2-10.6 MAGTF Meteorological and Oceanographic Support, 4 Apr 2018).
RRP (repair and replenishment point) — A combat service support installation, normally in forward areas near
the supported unit, established to support a mechanized or other rapidly moving force. It may be either a
prearranged point or a hastily selected point to rearm, refuel, or provide repair services to the supported force
(MCRP 1-10.2 Marine Corps Supplement, 31 May 2018).
RSTA — Reconnaissance, surveillance, and target acquisition (DOD Dictionary, 1 Jan 2020).
sensor — 1. A device that responds to a physical stimulus (such as heat, light, sound, pressure, magnetism, or
a particular motion) and transmits a resulting impulse (as for measurement or operating a control)
(Merriam-Webster, 2020).
shadow
cast shadow — A cast shadow is a silhouette of an object projected against its background. It is the
more familiar type of shadow and can be highly conspicuous. In desert environments, a shadow cast by
a target can be more conspicuous than the target itself (ATP 3-37.34 / MCTP 3-34C Survivability
Operations, 16 Apr 2018) (NO DOD definition).
5-4
contained shadow — a contained shadow is the dark pool that forms in a permanently shaded area.
Examples are the shadows under the track guards of an armored fighting vehicle, inside a slit trench,
inside an open cupola, or under a vehicle. Contained shadows show up much darker than their
surroundings and are easily detected by an enemy (ATP 3-37.34 / MCTP 3-34C Survivability
Operations, 16 Apr 2018) (NO DOD definition).
signature — A characteristic of an indicator that makes it identifiable (Marine Corps Concept of Signature
Management, 24 Oct 2017) (NO DOD or USMC definition).
physical signature — Physical signatures are those that can be collected by adversary
geospatial-intelligence assets or through direct observation (Marine Corps Concept of Signature
Management, 24 Oct 2017) (NO DOD or USMC definition).
administrative signature — Administrative signatures are those that an individual or unit creates when
conducting planning, movement, contracting, or other administrative actions and that can be collected
on by adversary Open Source Intelligence (OSINT), Signals Intelligence (SIGINT), or human source
intelligence (HUMINT) (Marine Corps Concept of Signature Management, 24 Oct 2017) (NO DOD or
USMC definition).
technical signature — Technical signatures are those that can be collected by adversary signal
intelligence (SIGINT) assets (Marine Corps Concept of Signature Management, 24 Oct 2017) (NO DOD
or USMC definition).
SIGMAN (signature management) — The process by which we understand own-force signatures and indicators,
identify methods and capabilities to collect and analyze those signatures, develop and implement
countermeasures to mask those signatures; and when necessary develop and implement methods to project
false signatures which protect friendly forces from adversary exploitation; or to draw the adversary toward a
specific course of action or position of disadvantage (Marine Corps Concept of Signature Management, 24 Oct
2017) (NO DOD or USMC definition).
SRBM (short-range ballistic missile) — A ballistic missile with a range capability between 300-600 nautical miles
(DOD Dictionary, 1 Jan 2020).
SR (sunrise) — The instant when the upper edge of the sun appears on the sea-level horizon (MCRP 2-10.6
MAGTF Meteorological and Oceanographic Support, 4 Apr 2018).
SS (sunset) — The instant when the upper edge of the sun disappears below the sea-level horizon (MCRP
2-10.6 MAGTF Meteorological and Oceanographic Support, 4 Apr 2018).
TAA (tactical assembly area) — An area that is generally out of the reach of light artillery and the location where
units make final preparations (pre-combat checks and inspections) and rest, prior to moving to the line of
departure (DOD Dictionary, 1 Jan 2020).
TAC-D (tactical deception) — Deception executed by tactical commanders not necessarily linked to a higher
MILDEC plan (NO DOD or USMC definition).
thermal crossover — The natural phenomenon that normally occurs twice daily when temperature conditions
are such that there is a loss of contrast between two adjacent objects on infrared imagery (DOD Dictionary, 1
Jan 2020).
5-5
terminal phase — That portion of the flight of a ballistic missile that begins when the warhead or payload
reenters the atmosphere and ends when the warhead or payload detonates, releases its submunitions, or
impacts (DOD Dictionary, 1 Jan 2020).
unknown — 1. A code meaning “information not available.” 2. An unidentified target. An aircraft or ship that has
not been determined to be hostile, friendly, or neutral using identification friend or foe and other techniques, but
that must be tracked by air defense or naval engagement systems. 3. An identity applied to an evaluated track
that has not been identified (DOD Dictionary, 1 Jan 2020).
WEZ (weapon engagement zone) — In air and missile defense, airspace of defined dimensions within which the
responsibility for engagement of air threats normally rests with a particular weapon system (DOD Dictionary, 1
Jan 2020).
1 Aug 2020
5-6
Reference
Bibliography
Purpose. To list sources for SIGMAN and camouflage.
Chad Skaggs
Walker Mills
“On Drones and Tactics: How Unmanned Platforms Will Change the Way the Infantry Fights.”
Modern War Institute at West Point, 6 Nov 2018.
“AAR from 1st Battalion, 4th Marines MCCRE Regarding Small Unmanned Aerial Systems.”
CamPen, CA: 2nd Battalion, 1st Marines, 30 Jun 2018.
Eric Todorski
Field Craft I: Gear and Personal Sustainment. Quantico, VA: TBS, 2020.
Field Craft II: Camouflage and Concealment. Quantico, VA: TBS, 2020.
Field Craft III: Position Concealment LP/OP. Quantico, VA: TBS, 2020.
Cornelison
Counter UAS TTPs. CamLej, NC: 2nd Battalion, 6th Marines, 2018.
ATP 3-37.34 / MCTP 3-34C Survivability Operations, 16 April 2018. 190 pages.
Superseded ATP 3-37.34 / MCWP 3-17.6 Survivability Operations, 28 Jul 2013
ATTP 3-34.39 / MCRP 3-17.6A Camouflage, Concealment, and Decoys, 26 Nov 2010.
Superseded FM 20-3 Camouflage, Concealment, and Decoys, 30 Aug 1999.
5-7
U.S. Army
ATP 3-01.8 Techniques for Combined Arms for Air Defense, 29 Jul 2016.
5-8
Articles
AFH 10-222 V10 Civil Engineer Camouflage, Concealment, and Deception (CCD) Measures,
18 Feb 2011. 114 pages.
Beals, Joseph T. Enemy Unmanned Combat Aerial Vehicles. Quantico, VA: MCU, 2011.
Flynn, Krebs, and Gentil. “Talon Reach VI AAR.” Quantico, VA: MCCLL, 17 Sep 2015.
Flynn, Krebs, and Gentil. “Talon Reach VII AAR.” Quantico, VA: MCCLL, 16 Jun 2016.
Gills, Jonathan. “In Over Their Heads: U.S. Ground Forces are Dangerously Unprepared for
Enemy Drones.” War On the Rocks, 30 May 2017.
Grau, Lester and Chuck Bartles. “Integration of Unmanned Aerial Systems within Russian
Artillery.” Fires, May-June 2016.
Minton, Sean. “The UAS Training Imperative: How to Implement C-UAS Training at the
Company Level.” Infantry, Spring 2019, pp 20-24.
Niggl, Paul, Frank Miner, and Mark Sousa. “Call for Fire.” Marine Corps Gazette, Dec 2018, pp
25-29.
Papa, Joseph and George Fahlsing. Camouflaging Vehicles Using Field Expedient Materials,
Commercial Hardware Store Materials, Camouflage Nets, and Rubber Conveyor Belt
Material. Fort Belvoir, VA: U.S. Army Research Development and Engineering
Command, 1 Dec 2005.
Phillips, Jeremy. “Training for the Enemy UAV Threat.” Infantry, May-Jun 2013, pp 46-47.
Historical Studies
In the spring of 1944, the U.S. Army printed a series of nine camouflage manuals to prepare
for the invasion of France. Highly detailed and well-illustrated, these manuals reflect an Army
without air superiority preparing to fight under German air observation and air attack.
5-9
Japanese Army Camouflage during World War II, 1938-1945.
North Korean People’s Army (NKPA) Camouflage during the Korean War, 1950-1953.
People’s Liberation Army (PLA) Camouflage during the Korean War, 1950-1953.
North Vietnamese Army (NVA) Camouflage during the Vietnam War, 1962-1975.
1 Aug 2020.
5-10
Reference
Observers for the Organization for Security and Co-operation in Europe (OSCE) use UAS to observe
Russian Army units inside Ukraine.
5-11
1 Aug 2020
5-12
Reference
Infantry battalion TAA from 2014 ft MSL. Infantry Company CP from 1519 ft MSL.
Infantry, on road in daylight, from 1483 ft MSL. Infantry, on road at night, from 1404 ft MSL.
Vehicles dispersed, from 1499 ft MSL. Vehicles raising dust, from 817 ft MSL.
5-13
Good effort at concealment in the treeline, but netting Good effort at concealment, but square, shiny tarps do
does NOT match background. From 1178 ft MSL. NOT match background. From 1453 ft MSL.
Good effort. Tan uniforms blend with background. Good effort. Mortar section is undetectable.
From 935 ft MSL. From 1548 ft MSL.
Synthetic sandbags shine “like light bulbs.” Contained shadows make fighting positions visible.
From 100 ft AGL. From 500 ft AGL.
Notes
1. Patterns—rows of vehicles, tents, packs, pallets, or tarps—are easily seen from the air.
5-14
2. Roads are easily viewed from the air. Shadows and dark uniforms contrast with light-colored
roads. After dusk, roads retain heat.
3. Vehicles are easily seen from the air. Even when dispersed in foliage, vehicles still need
camouflage netting. Vehicles on dirt roads raise dust clouds.
4. Vehicle tracks—in grass, dirt, or sand—are easily seen from the air. Tracks are difficult to
avoid or erase.
5. Square, shiny tarps are easily seen from the air. Tarps often do NOT blend with the
background.
7. Contained shadows—in fighting positions and vehicle netting—are easily seen from the air.
8. Marines in building windows are easily seen from the air with IR thermal sights.
References
Walker Mills. AAR from 1/4 MCCRE Regarding UAS. CamPen, CA: 2/1, 30 Jun
2018.
1 Aug 2020
5-15
www.warfighting.us
5-16
SIGMAN Camouflage SOP:
A Guide to Reduce Physical Signature Under UAS
www.warfighting.us