SERVICE MANUAL

CODE: 00ZARLC6//A1E

DIGITAL COPIER/PRINTER/
MULTIFUNCTIONAL SYSTEM OPTION
LARGE CAPACITY TRAY

MODEL AR-LC6
CONTENTS

[1] OUTLINE OF THE PRODUCT . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[2] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[3] INTERNAL CONSTRUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

[4] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

[5] DISASSEMBLY, ASSEMBLY, MAINTENANCE . . . . . . . . . . . . . . . 5-1

[6] ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1

[7] TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1

[8] ELECTRICAL SECTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.

This document has been published to be used

SHARP CORPORATION for after sales service only.
The contents are subject to change without notice.
[1] OUTLINE OF THE PRODUCT [2] SPECIFICATIONS
This model is a large capacity paper feed tray installed to the main unit. Transport speed Corresponds to 55 – 70 sheet/min.
It stores 3,500 sheets, eliminating troublesome paper supply. Transport reference Center reference
Paper size AB series A4
Inch series 8.5" x 11"
Paper size setting Not provided.
Factory setting of AB series A4
paper size Inch series 8.5" x 11"
Kind/weight of Normal paper 60 – 105g/m2 (16 – 28lbs)
applicable paper
Paper capacity 3,500 sheets (80g/m2)
Remaining paper Enable (Paper empty and 6 steps)
detection
Paper feed system Front loading, paper feed from the upper
section
Tray lift time Up: max. 15sec
Down: max. 5sec
Power consumption Normal operation 26.4W or less
AR-LC6 Lift up 42W
Power source 24V and 5V are supplied from the main unit
External dimensions 376 (W) x 545.5 (D) x 517.5 (H) mm
Occupying area 376 (W) x 545.5 (D) mm
Weight About 35kg or less
Paper feed system Paper pick-up by the take-up roller, Torque
limiter reverse rotation separation system
Humidifying heater Power supplied from the main unit, ON/OF
control by the main unit
Heater kit support
Factory setting AB series A4
Inch series LT

AR-LC6 OUTLINE OF THE PRODUCT 1 - 1

[3] INTERNAL CONSTRUCTION
1. Motor, clutch, solenoid

3 4
1
5 2

Parts
No. MODEL NOTE
Code Signal name Name Type Function/Operation Active condition
1 LTM LTM Transport Drives the paper feed, and the When paper feed is started,
motor paper transport section. "H" level.
2 LLM LLM Lift motor Synchronous Lifts the paper feed table. When the lower limit sensor
motor is ON, "H" level. When the
upper limit sensor is ON, "L"
level.
3 LTCL LTCL Transport Controls ON/OFF of the
clutch transport roller.
4 LPFCL LPFCL Paper feed Controls ON/OFF of the paper When paper feed is started,
clutch feed roller. "H" level. After starring
transport (pickup OFF), it is
turned OFF by the timer.
5 LPSL LPSL Paper feed Presses the paper pickup roller Turned OFF after starting
solenoid onto paper. transport. Turned ON by the
timer.
∗ Lift-up – When paper
empty detection is made:
ON
6 LTLSL LTLSL Tray lock The tray is locked so that the When paper feed is started,
solenoid tray cannot be pulled out during "H" level.
paper feed.

AR-LC6 INTERNAL CONSTRUCTION 3 - 1

2. PWB, sensor
11
16
15
13
7
14

10

Parts
No. MODEL NOTE
Code Signal name Name Type Function/Operation Active condition
7 MAIN PWB – LCC main Controls and drives the LCC.
PWB
8 LLD LLD Lower limit The lower limit of the tray is When lifting up, "L" level.
sensor detected.
9 LRE LRE Lift motor The lift motor rotation is Pulse signal
encoder detected.
10 LCD LCD Cassette The tray insertion is detected.
detection
11 LTOD LTOD The main unit Detects connection to the main
connection unit.
sensor
12 LTD LTD Transport Detects paper transport. When paper feed is
sensor performed, when the
paper feed solenoid is "L,"
it is "H" level.
13 LUD LUD Upper limit Detects the paper upper limit When "H" level (ON), the
sensor position. lift-up motor stops.
14 LPED LPED Paper Detects paper presence/empty When paper is detected,
presence/ on the paper tray. "H."
empty sensor ∗ When lifting up, if "L"
with LRE 800 pulse, the
paper feed solenoid is
ON.
15 LLSW LLSW Upper limit Protects the paper feed unit
switch from breakage due to lifting the
tray too much.
16 LOSW LOSW Upper open/ Detects open/close of the
close switch upper door.
17 DH DH Thermal Keeps temperature in the LCC
heater tray.

AR-LC6 INTERNAL CONSTRUCTION 3 - 2

[4] OPERATIONAL DESCRIPTIONS
1. Lift operation
When the main unit is turned ON, if the tray is at the lower limit position If the paper presence/empty sensor (LPED) is not turned on within 800
(lower limit sensor: LLD ON position), the lift motor is turned ON to lift pulses, the paper feed solenoid is turned ON with the lift motor ON to
the tray. move down the pickup roller. Then, the lift motor is turned ON again to
When the paper presence/empty sensor (LPED) is turned ON within lift the tray. The lift motor is stopped at the upper limit sensor (LUD) ON
800 pulses of the encoder signal from start of lifting up the tray, the lift position, and the paper feed solenoid is turned OFF.
motor is turned OFF to stop the tray, and the paper feed solenoid is When the machine power is turned on, if the tray is on the paper feed
turned ON to mode down the pickup roller. After that, the lift motor is position, lifting is not performed.
turned ON to lift the tray. The tray is stopped when the upper limit sen- When the tray is pulled out, it moves down by its own weight.
sor (LUD) is turned ON.

Lifting up operation (When LPED is turned ON within 800 pulses Lifting up operation (When LPED is not turned ON within 800
of encoder.) pulses of encoder.)

200 msec LLM

LLM (Lift motor output)
(Lift motor output) LLD
LLD (Lower limit sensor)
(Lower limit sensor)
LUD
(Upper limit sensor)
LUD
(Upper limit sensor)
LPED
(Paper empty detection)
LPED
(Paper empty detection) LPSL
LPSL (Solenoid) Within 800 pulses
(Solenoid) Within 800 pulses LRE
(Encoder signal)
LRE
(Encoder signal)

2. Paper feed operation When the transport clutch (LTRC) is turned ON with the transport
motor (LPFM) ON (rotating), the transport roller rotates. When the
When the tray is stationary at the paper feed position (upper limit sen- paper feed clutch (LPFC) is turned on under this state, the paper feed
sor: LUD ON position) and there is paper on the tray, paper feed oper- roller and the take-up roller rotate. When the paper feed solenoid
ation can be performed. (LPFS) is turned ON, the take-up roller is pushed down to press paper.
Paper feed operation is performed by the transport motor (LTM), the During paper feed operation, the tray lock solenoid (LTLSL) is turned
transport clutch (LTCL), the paper feed clutch (LPFCL), and the paper ON to inhibit pulling out the tray.
feed solenoid (LPSL) at the following timing.

LCC paper feed time chart

Paper feed start Resist stop Resist stop Resist stop

Clearance-between- Clearance-between- Clearance-between- Clearance-between-
papers control timer papers control timer papers control timer papers control timer

LTM
(Transport motor)

LTD
(Transport sensor)
PIC drop timer PIC drop timer PIC drop timer PIC drop timer
LPSL
(Paper feed solenoid)
Paper feed clutch Paper feed clutch Paper feed clutch Paper feed clutch Paper feed clutch
LPFCL OFF timer OFF timer OFF timer OFF timer OFF timer
(Paper feed clutch)

LTCL
(Transport clutch)

TRC
(Main unit
synchronous signal)
LTLSL
(Tray lock solenoid)

Preliminary Preliminary Preliminary Preliminary Preliminary

paper feed start paper feed start paper feed start paper feed start paper feed start
First sheet Second sheet Third sheet Fourth sheet Fifth sheet
Preliminary paper Preliminary paper Preliminary paper Preliminary paper Preliminary paper
feed complete feed complete feed complete feed complete feed complete
Paper feed start Paper feed start Paper feed start

AR-LC6 OPERATIONAL DESCRIPTIONS 4 - 1

 5
1
4
6
3 7

1 Paper feed roller clutch

2 Take-up roller
3 Paper feed roller
4 Paper feed solenoid
5 Transport clutch
6 Transport motor
7 Tray lock solenoid
8 Lift-up motor

3. Paper empty detection

When the tray lifts and stops at the paper feed position and during
paper feed operation, paper presence/empty is detected by the paper
presence/empty sensor (LPED).
When paper empty is detected in the tray during paper feeding, paper
feeding is stopped.

AR-LC6 OPERATIONAL DESCRIPTIONS 4 - 2

[5] DISASSEMBLY, ASSEMBLY, MAINTENANCE
1. Maintenance system table
✕: Checking (clean, replace or adjust as required) ❍: Cleaning ▲: Replace ∆: Adjust ✩: Lubricate ❏: Position shift
AR-M550U/M550N
250K 500K 750K 1000K 1250K 1500K 1750K 2000K
(PM: 250K) When
Remark
AR-M620U/M620N calling
300K 600K 900K 1200K 1500K 1800K 2100K 2400K
(PM: 300K)
Unit name No. Part name (Note)
Paper feed 1 Paper pickup roller/ (Note)
✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
separation Paper feed rollers
section 2 Torque limiter ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Transport 3 Transport rollers ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
section 4 Transport paper guides ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Gears (Specified position)
Drive 5 Gears ✕ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩
section 6 Belt ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Others 7 Sensors ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
(Note) Replacement reference: For replacement, refer to each paper feed port counter value.
Paper feed roller related section: 200K or 1 year
Torque limiter: 800K

2. Maintenance parts replacement procedures

A. Paper feed roller 4) Remove the screw, and remove the paper guide block.
1) Pull the lever, and open the upper cover. 5) Remove the pawl, and remove the reverse roller.
2) Remove the screw, and remove the sheet.

3) Remove the pawl, and remove the pickup roller and the paper feed
roller.

AR-LC6 DISASSEMBLY, ASSEMBLY, MAINTENANCE 5 - 1

3. Each unit removal B. Paper feed tray
1) Pull out the tray.
A. Paper feed unit
2) Remove the screws from the left and right rail sections.
1) Pull out the tray.

2) Open the upper cover, and remove three screws. 3) Remove the tray unit from the rail.
3) Remove the upper cabinet.

4) Disconnect the connectors (2 positions).

C. Drive unit
1) Remove the screw, and remove the rear cover.

5) Remove the screw, and remove the paper feed unit.

2) Remove the connectors (2 positions).

AR-LC6 DISASSEMBLY, ASSEMBLY, MAINTENANCE 5 - 2

3) Remove the screw, and remove the drive unit. 4) Remove the screw, and remove the lift motor.

5) Remove the ring, and remove the pulley.

4. Major parts removal
A. Motor (Main)
1) Remove the screw, and remove the rear cover.
2) Disconnect the connector.
3) Remove the screw, and remove the motor.

C. Clutch
1) Remove the paper feed unit. (Refer to "3. Each unit removal.")
2) Remove the screw, and remove the cover.

B. Lift motor
1) Remove the drive unit.
2) Remove the E-ring, and remove the parts.

3) Remove the E-ring, and remove the parts.

3) Remove the screw, and remove the cover.

AR-LC6 DISASSEMBLY, ASSEMBLY, MAINTENANCE 5 - 3

4) Disconnect the connector, and remove the screw. D. Paper feed solenoid
1) Remove the paper feed unit.
2) Remove the cover.
3) Remove the screw, and remove the unit.

5) Remove the frame.

4) Disconnect the connector.

5) Remove the screw, and remove the solenoid.

6) Remove the connector, and the E-ring, and remove the paper feed
transport clutch.

E. Torque limiter
1) Remove the paper feed unit.
2) Remove the cover.
3) Remove the E-ring and the screw, and remove the parts.

4) Lift the shaft, and remove the torque limiter.

AR-LC6 DISASSEMBLY, ASSEMBLY, MAINTENANCE 5 - 4

F. Transport roller
1) Remove the paper feed unit.
2) Remove the cover.
3) Remove the spring, and remove the screw.

4) Remove the plate cover, and remove the lever.

5) Remove the clutch.

6) Remove the screw and the E-ring, and remove the parts.
7) Remove the transport roller.

AR-LC6 DISASSEMBLY, ASSEMBLY, MAINTENANCE 5 - 5

[6] ADJUSTMENT
Each adjustment item in the adjustment item list is indicated with its JOB number. Perform the adjustment procedures in the sequence of Job numbers
from the smallest to the greatest.
However, there is no need to perform all the adjustment items. Perform only the necessary adjustments according to the need.
Unnecessary adjustments can be omitted. Even in this case, however, the sequence from the smallest to the greatest JOB number must be observed.
If the above precaution should be neglected, the adjustment would not complete normally or a trouble may occur.

1. Setting item list

Simulation to
Job No. Adjustment item list
be used
ADJ 1 Print off-center adjustment 50-10
ADJ 2 Resist amount adjustment ADJ 2A Adjustment in the resist amount adjustment mode 51-2
ADJ 2B Adjustment in the print lead edge adjustment mode 50-5

2. Details 3) Select "0: TRAY SELECT" and press START key.

The display is shown as follows. Select "6: LCC" as the paper feed
tray, and press START key.
ADJ 1 Print off-center adjustment SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 1-16, AND PRESS
1) Set the print off-center adjustment mode of SIM 50-10 by the key START.
operation of the machine. (Press the keys as shown below to enter
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
1
SIM 50-10.) 5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE)
#/P ∗ C ∗ 5 0 1 0
4) The display is shown as follows again. Select "8: LCC" and press
START key.
2) In SIM 50-10, the display is shown as follows. The print off-center
adjustment value can be set for each paper feed tray. SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
START.
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
2
START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
2 (ADJUSTMENT DATA)
3.TRAY1 50 4.TRAY2 50 5.TRAY3 50
6.TRAY4 50 7.BPT 50 8.LCC 50 9. ADU 50
(ADJUSTMENT DATA)
3.TRAY1 50 4.TRAY2 50 5.TRAY3 50
6.TRAY4 50 7.BPT 50 8.LCC 50 9. ADU 50 5) Then enter the adjustment value with 10-key.
(Default: 50, Adjustment range: 0 – 99)
• When the adjustment value is decreased by 1, the image is
Adjustment position Set value shifted to the rear side by 0.1mm.
Display Set • When the adjustment value is increased by 1, the image is
Item description Default
item range shifted to the front side by 0.1mm.
TRAY1 TRAY1 Print off center
adjustment position SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. INPUT VALUE 0-99, AND
TRAY2 TRAY2 Print off center
PRESS START.
(LCC left adjustment position 8.LCC 50
side)
TRAY3 TRAY3 Print off center
6) Enter the adjustment value and press START key, and printing is
(LCC right adjustment position
started and the set value is stored.
side)
TRAY4 TRAY4 Print off center SIMULATION 50-10
adjustment position PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.

MFT Manual Print off center

paper feed adjustment position
LCC Large Print off center 50 0 to Shift by 7) Check the printed self-print result, and repeat procedures 5) – 6)
capacity tray adjustment position 99 0.1mm for until the value is in the range of 0 ± 3mm.
set value 1 When the value is in the above range, press CA key to terminate
ADU Duplex Print off center the simulation.
adjustment position
(ADU) (Rear side)
a

Print lead edge

b
(Front side)
Adjust in the range
of the figure
(0 ± 3mm).

(Print back surface)

AR-LC6 ADJUSTMENT 6 - 1
 ADJ 2 Resist amount adjustment ADJ 2A Adjustment in the print lead edge
adjustment mode
ADJ 2A Adjustment in the resist amount 1) Set the print lead edge adjustment mode of SIM 50-5 by the key
adjustment mode operation of the machine.

1) Set the resist amount adjustment mode of SIM 51-02 by the key #/P ∗ C ∗ 5 0 5
operation of the machine.

2) In SIM 50-5, the display is shown as follows. The resist amount

#/P ∗ C ∗ 5 1 2
adjustment value can be set for each paper feed tray.

2) In SIM 51-02, the display is shown as follows. The resist amount SIMULATION 50-5
adjustment value can be set for each paper feed tray. LEAD EDGE ADJUSTMENT. SELECT 0-12, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
SIMULATION 51-2
(ADJUSTMENT DATA)2.RRCB 50
3.TRAY1 50 4.TRAY2 50 5.TRAY3 50
2
RESIST TIMING ADJUSTMENT. SELECT 0-14, AND PRESS START. 6.TRAY4 50 7.BPT 50 8.LCC 50 9.ADU 50
0.TRAY SELECT 1 1.PRINT START (VOID AREA SETTING) 10.DENA 50 11.DENB 30 12.FR VOID 30
2.TRAY1 50 3.TRAY2 50 4.TRAY3 50
5.TRAY4 50 6.BPT 50
8.ADU
7.LCC 50
50 9.SPF(TOP) 50 10.SPF(HIGH) 50
1 3) Select "0: TRAY SELECT" and press START key.
11.SPF(LOW) 50 12.SPF FEED(TOP) 50 The display is as shown below. Select "6: LCC" as the paper feed
13.SPF FEED(HIGH) 50 14.SPF FEED(LOW) 50 tray and press START key.

SIMULATION 50-5
3) Select "0: TRAY SELECT" and press START key. LEAD EDGE ADJUSTMENT. SELECT 1-6, AND PRESS START.
The display is shown as follows. Select "6: LCC" as the paper feed (FEED TRAY)
tray, and press START key. 1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 1
5.BPT 6.LCC
SIMULATION 51-2 (ABOVE+10: DUPLEX MODE)
RESIST TIMING ADJUSTMENT. SELECT 1-6, AND PRESS START.
(FEED TRAY) 4) The display is as shown below again. Select "8: LCC" and press
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
START key.
5.BPT 6.LCC
(ABOVE+10: DUPLEX MODE) 1 SIMULATION 50-5
LEAD EDGE ADJUSTMENT. SELECT 0-12, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
4) The display is shown as follows again. Select "7: LCC" and press
START key.
(ADJUSTMENT DATA)2.RRCB 50
3.TRAY1 50 4.TRAY2 50 5.TRAY3 50
2
6.TRAY4 50 7.BPT 50 8.LCC 50 9.ADU 50
(VOID AREA SETTING) 10.DENA 50 11.DENB 30 12.FR VOID 30
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. SELECT 0-14, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START 5) Then, enter the adjustment value with 10-key.
2.TRAY1 50 3.TRAY2 50 4.TRAY3 50 (Default: 50, Adjustment range: 0 – 99)
5.TRAY4 50 6.BPT 50
8.ADU
7.LCC 50
50 9.SPF(TOP) 50 10.SPF(HIGH) 50
1 • When the adjustment value is increased by 1, the resist amount
11.SPF(LOW) 50 12.SPF FEED(TOP) 50
is increased by 1msec.
13.SPF FEED(HIGH) 50 14.SPF FEED(LOW) 50
SIMULATION 50-5
LEAD EDGE ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
5) Then enter the adjustment value with 10-key. START.
(Default: 50, Adjustment range: 0 – 99) 8.LCC 50
• When the adjustment value is increased by 1, the resist amount
is increased by 1msec. 6) After entering the adjustment value, press START key, and print-
ing is started and the set value is stored.
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
SIMULATION 50-5
START.
7.LCC 50 LEAD EDGE ADJUSTMENT. NOW PRINTING.

6) Enter the adjustment value and press START key, and printing is
7) After completion of the adjustment, press [CA] key to terminate the
started and the set value is stored.
simulation mode.
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. NOW PRINTING.

7) After completion of the adjustment, press [CA] key to terminate the

simulation mode.

AR-LC6 ADJUSTMENT 6 - 2
[7] TROUBLESHOOTING
1. General
Monitors the machine
When a trouble occurs in the machine or when the life of a consumable conditions.
part is nearly expired or when the life is expired, the machine detects
and displays it on the display section or notifies to the user or the ser-
Detects/analyzes
viceman by voice messages. This allows the user and the serviceman the content.
to take the suitable action. In case of a trouble, this feature notifies the
occurrence of a trouble and stops the machine to minimize the dam-
age.
Warning
Trouble/Warning
2. Function and purpose
1) Securing safety. (The machine is stopped on detection of a trou- Trouble
ble.)
2) The damage to the machine is minimized. (The machine is The machine is stopped.
stopped on detection of a trouble.)
3) By displaying the trouble content, the trouble position can be
quickly identified. (This allows to perform an accurate repair, The content is displayed.
improving the repair efficiency.)
4) Preliminary warning of running out of consumable parts allows to
arrange for new parts in advance of running out. (This avoids stop- Warning A consumable NO
ping of the machine due to running out the a consumable part.) Trouble/Warning part has reached
its lifetime.
3. Self diag message kinds Trouble YES
The self diag messages are classified as shown in the table below. Replace or supply
Troubleshoot the cause.
Class 1 User Warning of troubles which can be recovered by the consumable part.
the user. (Paper jam, consumable part life
expiration, etc.)
Repair
Service Warning of troubles which can be recovered
man only by a serviceman. (Motor trouble,
maintenance, etc.) Cancel the self-
Other — diagnostic message with
Class 2 Warning Warning to the user, not a machine trouble the diagnostics
(Preliminary warning of life expiration of a (test commands).
consumable part, etc.)
Trouble Warning of a machine trouble. The machine is
Reset
stopped.
Other —

Standby state
4. Self diag operation
A. Self diag operation and related work flow
The machine always monitors its own state.
When the machine recognizes a trouble, it stops the operation and dis-
plays the trouble message.
A warning message is displayed when a consumable part life is nearly
expired or is expired.
When a warning message is displayed, the machine may be or may
not be stopped.
The trouble messages and the warning messages are displayed by the
LCD.
Some trouble messages are automatically cleared when the trouble is
repaired. Some other troubles must be cleared by a simulation.
Some warning messages of consumable parts are automatically
cleared when the trouble is repaired. Some other warning messages
must be cleared by a simulation.

AR-LC6 TROUBLESHOOTING 7 - 1
5. List
MAIN SUB
No. Title (Content) Section Operation mode Countermeasure (Remedy) Note
CODE CODE
1 U6 09 Lift motor trouble LCC Tray lift-up Check connection.
2 20 Communication trouble LCC LCC communication Turn OFF/ON the power.
3 21 Transport motor trouble LCC Paper feed Check connection.
4 22 24V trouble LCC Power ON Check connection.

6. Details
Main Sub Title Lift motor trouble Main Sub Title Transport motor trouble
U6 09 Display Message U6 21 Display Message
Phenomenon Detail LCC lift motor operation Phenomenon Detail LCC transport motor
trouble. Tray lift-up trouble operation trouble
Section LCC Section LCC
Case 1 Cause Defective connection or Case 1 Cause Defective connection or
disconnection of connector disconnection of connector
and harness and harness
Check Check the connector and Check Check the connector and
and the harness in the motor and the harness in the motor
Remedy line. Connect the connector Remedy line. Connect the connector
properly. Replace the properly. Replace the
harness. harness.
Case 2 Cause Motor lock, motor rpm Case 2 Cause Motor lock, motor rpm
abnormality, motor abnormality, motor
overcurrent, LRE trouble, overcurrent, intrusion of
intrusion of foreign material foreign material
Check Use SIM 4-2 to select LRE Check Use SIM 4-3 to select LTM
and and check the operation of and and check the operation of
Remedy the single unit. Use SIM 4-3 Remedy the single unit. Check for
to select LLM and check the intrusion of any foreign
operation of the single unit. material in the drive system.
Check for intrusion of any Case 3 Cause LCC main PWB trouble,
foreign material in the drive transport motor trouble
system. Check Replace the LCC main PWB
Case 3 Cause LC main PWB trouble, lift and or the transport motor.
motor trouble Remedy
Check Replace the LCC main PWB
and or the lift motor. Main Sub Title 24V trouble
Remedy U6 22 Display Message
Phenomenon Detail 24V supply for LCC is cut
Main Sub Title Communication trouble off.
U6 20 Display Message Section LCC
Phenomenon Detail Communication error with Case 1 Cause Defective connection or
LCC, communication line disconnection of connector
test error after turning on the and harness
power or canceling an Check Check the connector and
exclusive simulation. and the harness which connect
Section LCC Remedy LCC and the main unit.
Case 1 Cause Defective connection or Connect the connector
disconnection of connector properly. Replace the
and harness harness.
Check Check the connector and Case 2 Cause Power source fuse blown-off
and the harness of the Check Check for short circuit
Remedy communication line. and between 24V and GND.
Connect the connector Remedy Check for pinched harness
properly. Replace the and the LCC main PWB
harness. trouble. Replace the fuse,
Case 2 Cause LCC main PWB trouble, the harness, and the LCC
control PWB (PCU) trouble main PWB.
Check Replace the LCC PWB. Case 3 Cause Power source abnormality in
and Replace the control PWB the main unit
Remedy (PCU). Check Check 24V output on the
Case 3 Cause Malfunction caused by and main unit side.
noises Remedy
Check Cancel by turning OFF/ON
and the power.
Remedy

AR-LC6 TROUBLESHOOTING 7 - 2
 <Paper feed unit>
SMP-18V-NC SMR-18V-N PHR-3
1 1 1 GND2
2 2 2 /LPED LPED Tray paper sensor Main unit
3 3 3 +5V
4 4 PHR-3
5 5 1 GND2
6 6 2 /LUD LUD Tray upper limit sensor
7 7 3 +5V
8 8
9 9 SMP-03V-NC SMR-03V-N
10 10 1 1
LPSL Paper feed solenoid
11 11 2 2
12 12 3 3
13 13 SMP-02V-NC SMR-02V-N
14 14 1 1
LPFCL Paper feed clutch
15 15 2 2
16 16
17 17 SMR-03V-N SMP-03V-NC PHR-3
18 18 1 1 1 +5VR
2 2 2 GND2 LTD Paper transport sensor
3 3 3 /LTD

CZHR-03V-S
1 +24V
ELR-04NV ELP-04NV 2 N.C. LTCL Paper transport clutch
1 1 3 LTCL
1. Actual wiring chart

2 2
3 3 FPS-187
4 4 1 COM
2 ON LLSW Upper limit switch
3 NC
PS-187-3V
1 COM
2 ON LOSW Upper open/close switch
3 NC

SMR-03V-N SMP-03V-NC 179228-3

1 1 1 +5V
2 2 2 LTOD LTOD The main unit connection sensor
[8] ELECTRICAL SECTION

3 3 3 GND2

SMP-03V-NC SMR-03V-N
1 1 1 LCD

9
8
7
6
5
4
3
2
1

9
8
7
6
5
4
3
2
1
10

24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
2 2 2 GND2 LCD Cassette detection
3 3 3 +5V

CN-D

CN-C

+5V
+5V
+5V
+5V
+5V
ELP-03V ELR-03V

/LTD
+24V
+24V

/LUD
+24V
+24V

LTCL

+5VR
GND2
GND2
GND2
GND2
GND2

LTOD
GND2
GND2
GND2
GND2
GND2
GND2
GND1

EXIN2
EXIN1
/LPED
1 1 1 LLM+

LPFCL
LIFT

B10B-PHDSS-B

B24B-PHDSS-B
2 2 Lift motor
3 3 2 LLM- MOTOR

LPSL(+24V)
+24V(LLSW)
+24V(LOSW)
+24V(LOSW)
PHR-5
1 +24V
CN-E 2 GND1
B14B-PHDSS-B 3 LTM LTM LCC transport motor
+5V 1 4 LTM-T
LCD 2 5 LTM-CLK
GND2 3
GND2 4
LLM 5
N.C. 6
LLM(GND) 7
N.C. 8
CN-B LTM-CLK 9 ELP-02V ELR-02V
B8B-PH-K-S LCC MAIN PWB LTM-T 10 1 1
1 +5V LTM 11 2 2 Heater
2 +5V GND1 12
3 LRE GND1 13
4 LLD +24V(LOSW) 14
5 GND2
Main unit connection
6 GND2
7 +24V ELP-12V ELR-12V
8 LTLSL 4 4 AC-L(H)

AR-LC6 ELECTRICAL SECTION 8 - 1

5 5 F.G.

MD
+5V

TXD
N.C.
N.C.
N.C.

RES
/TXD
/RES
+24V

FVpp
/RXD
CN-F
CN-A

TEST
12 12 AC-N(H)

GND2
GND1

+5V(VD)
TXD-LCC

RES-LCC
RXD-LCC

/TRC-LCC
/DTR-LCC
/DSR-LCC
Earth

GND2(VD)
ELP-15V ELR-15V

B11B-PH-K-S
1 1 N.C.

B12B-PHDSS-B
2 2 N.C.
3 3 TXD-LCC
4 4 RXD-LCC
5 5 /DTR-LCC

9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1

11
10
12
11
10
6 6 /DSR-LCC
7 7 RES-LCC
8 8 F.G.
9 9 +5V
10 10 GND2
11 11 +24V
12 12 GND1
13 13 /TRC-LCC
14 14 N.C.
15 15 N.C.

SMP-02V-NC SMR-02V-N
1 1
LTLSL
2 2 Tray lock solenoid

SMP-03V-NC SMR-03V-N
1 1 1 LRE
2 2 2 GND2 LRE Input lift motor encoder
3 3 3 +5V

SMP-03V-NC SMR-03V-N
1 1 1 LLD
2 2 2 GND2 LLD Lower limit sensor
3 3 3 +5V
 24V

Upper door open/close

switch (LOSW)
RXD-LCC 24V monitor
circuit
TXD-LCC
DSR-LCC Communication
buffer circuit Upper door detection
Main unit DTR-LCC monitor circuit
2. Block diagram

RES-LCC

Transport motor
(LTM)

Xtal CPU (HD64F3644H)

7.37MHz Arithmetic section Upper limit switch (LLSW)

Upper limit detection

monitor circuit
5V
GND2

Poly-switch 1.1A

24V
GND1
Lift motor drive
circuit
Lift motor (LLM)
Current limit
circuit
F.G.

Upper limit sensor

(LUD)
Lower limit sensor
(LLD)

Paper presence/empty
sensor (LPED)
Sensor input circuit
Paper exit sensor (LTD)

Main unit connection

AR-LC6 ELECTRICAL SECTION 8 - 2

sensor (LTOD)

Cassette sensor (LCD)

On-board write circuit
Remaining quantity
sensor (LRE)

Communication write circuit

Paper feed clutch

(LPFCL)

24V Power 12V circuit 12V Transport clutch

(LTCL)
Solenoid/clutch drive circuit
Tray lock solenoid
EEPROM (LTLSL)

Paper feed solenoid

(LPSL)

LCC MAIN PWB

LCC
LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.

Example:

<Solder composition code of lead-free solder>

Solder composition Solder composition Solder composition code

code (Refer to the Sn-Ag-Cu a
Lead-Free table at the right.)
Sn-Ag-Bi
b
Sn-Ag-Bi-Cu
Sn-Zn-Bi z
5mm
a Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
n
i

s
Bi-Sn-Ag-P p
Bi-Sn-Ag

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD

When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use
soldering iron is recommendable.

(2) NOTE FOR SOLDERING WORK

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is
inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed
the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is
confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after
completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.
 CIRCUIT DIAGRAM
CODE: 00ZARLC6/C1//

DIGITAL COPIER/PRINTER/
MULTIFUNCTIONAL SYSTEM OPTION
LARGE CAPACITY TRAY

MODEL AR-LC6
CONTENTS

[1] BLOCK DIAGRAM . . . . . . . . . . . . . . 1-1

[2] ACTUAL WIRING CHART . . . . . . . . 2-1

[3] CIRCUIT DIAGRAM . . . . . . . . . . . . . 3-1

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.

This document has been published to be used

SHARP CORPORATION for after sales service only.
The contents are subject to change without notice.
 24V

Upper door open/close

switch (LOSW)
RXD-LCC 24V monitor
circuit
TXD-LCC
DSR-LCC Communication
buffer circuit Upper door detection
Main unit DTR-LCC monitor circuit
RES-LCC

Transport motor
(LTM)

Xtal CPU (HD64F3644H)

7.37MHz
[1] BLOCK DIAGRAM

Arithmetic section Upper limit switch (LLSW)

Upper limit detection

monitor circuit
5V
GND2

Poly-switch 1.1A

24V
GND1
Lift motor drive
circuit
Lift motor (LLM)
Current limit
circuit
F.G.

Upper limit sensor

(LUD)
Lower limit sensor
(LLD)

Paper presence/empty
sensor (LPED)
Sensor input circuit
Paper exit sensor (LTD)

Main unit connection

sensor (LTOD)

AR-LC6 BLOCK DIAGRAM / ブロック図 1 - 1

Cassette sensor (LCD)
On-board write circuit
Remaining quantity
sensor (LRE)

Communication write circuit

Paper feed clutch

(LPFCL)

24V Power 12V circuit 12V Transport clutch

(LTCL)
Solenoid/clutch drive circuit
Tray lock solenoid
EEPROM (LTLSL)

Paper feed solenoid

(LPSL)

LCC MAIN PWB

LCC
 <Paper feed unit>
SMP-18V-NC SMR-18V-N PHR-3
1 1 1 GND2
2 2 2 /LPED LPED Tray paper sensor Main unit
3 3 3 +5V
4 4 PHR-3
5 5 1 GND2
6 6 2 /LUD LUD Tray upper limit sensor
7 7 3 +5V
8 8
9 9 SMP-03V-NC SMR-03V-N
10 10 1 1
LPSL Paper feed solenoid
11 11 2 2
12 12 3 3
13 13 SMP-02V-NC SMR-02V-N
14 14 1 1
LPFCL Paper feed clutch
15 15 2 2
16 16
17 17 SMR-03V-N SMP-03V-NC PHR-3
18 18 1 1 1 +5VR
2 2 2 GND2 LTD Paper transport sensor
3 3 3 /LTD

CZHR-03V-S
1 +24V
ELR-04NV ELP-04NV 2 N.C. LTCL Paper transport clutch
1 1 3 LTCL
2 2
3 3 FPS-187
4 4 1 COM
2 ON LLSW Upper limit switch
3 NC
PS-187-3V
1 COM
2 ON LOSW Upper open/close switch
3 NC

SMR-03V-N SMP-03V-NC 179228-3

1 1 1 +5V
2 2 2 LTOD LTOD The main unit connection sensor
3 3 3 GND2
[2] ACTUAL WIRING CHART

SMP-03V-NC SMR-03V-N
1 1 1 LCD

9
8
7
6
5
4
3
2
1

9
8
7
5
4
3
2
1
10

24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
2 2 2 GND2 LCD Cassette detection
3 3 3 +5V

CN-D

CN-C

+5V
+5V
+5V
+5V
+5V
ELP-03V ELR-03V

/LTD
+24V
+24V

/LUD
+24V
+24V

LTCL

+5VR
GND2
GND2
GND2
GND2
GND2

LTOD
GND2
GND2
GND2
GND2
GND2
GND2
GND1

EXIN2
EXIN1
/LPED
1 1 1 LLM+

LPFCL
LIFT

B10B-PHDSS-B

B24B-PHDSS-B
2 2 Lift motor
3 3 2 LLM- MOTOR

+24V(LLSW)

LPSL(+24V)
+24V(LOSW)
+24V(LOSW)
PHR-5
1 +24V
CN-E 2 GND1
B14B-PHDSS-B 3 LTM LTM LCC transport motor
+5V 1 4 LTM-T
LCD 2 5 LTM-CLK
GND2 3
GND2 4
LLM 5
N.C. 6
LLM(GND) 7
N.C. 8
CN-B LTM-CLK 9 ELP-02V ELR-02V
B8B-PH-K-S LCC MAIN PWB LTM-T 10 1 1
1 +5V LTM 11 2 2 Heater
2 +5V GND1 12
3 LRE GND1 13
4 LLD +24V(LOSW) 14
5 GND2
Main unit connection
6 GND2
7 +24V ELP-12V ELR-12V
8 LTLSL 4 4 AC-L(H)
5 5 F.G.

MD
+5V

TXD
N.C.
N.C.
N.C.

RES
/TXD
/RES
+24V

FVpp
/RXD
CN-F

TEST
CN-A
12 12 AC-N(H)

GND2
GND1

+5V(VD)
TXD-LCC

RES-LCC
RXD-LCC

/TRC-LCC
/DTR-LCC
/DSR-LCC
Earth

GND2(VD)
ELP-15V ELR-15V

B11B-PH-K-S
1 1 N.C.

AR-LC6 ACTUAL WIRING CHART / 実体配線図 2 - 1

B12B-PHDSS-B
2 2 N.C.
3 3 TXD-LCC
4 4 RXD-LCC
5 5 /DTR-LCC

9
8
7
6
5
4
3
2
1
9
8
7
6
5
4
3
2
1

11
10
12
11
10
6 6 /DSR-LCC
7 7 RES-LCC
8 8 F.G.
9 9 +5V
10 10 GND2
11 11 +24V
12 12 GND1
13 13 /TRC-LCC
14 14 N.C.
15 15 N.C.

SMP-02V-NC SMR-02V-N
1 1
LTLSL
2 2 Tray lock solenoid

SMP-03V-NC SMR-03V-N
1 1 1 LRE
2 2 2 GND2 LRE Input lift motor encoder
3 3 3 +5V

SMP-03V-NC SMR-03V-N
1 1 1 LLD
2 2 2 GND2 LLD Lower limit sensor
3 3 3 +5V
[3] CIRCUIT DIAGRAM
A B C

MAIN PWB
VD

+5V
R16
4.7k
1-3D

3
D13 D14 2-1A
R65 R70 R72 R71
/TXD
4.7k 4.7k 1k 4.7k
DAN202K 2-1A

C
TXD Q15
DAN202K
4 TXD-LCC B VD

2
CNA-7
/DTR-LCC
CNA-9
RES-LCC
CNA-11
/TRC-LCC R66 10k
CNA-12 /TRC RT1N141C R17
1-3D

E
4.7k

2
C35 C34
D8 D9 1-3D
473Z/16V 222Z/50V
DTR

C
DAP202K DAP202K Q14
VD
3

3
B

R32
RT1N141C

E
2-1A 4.7k
+5V 1-3C
RES 2-1A
NO ASSEMBLY /RES
473

C
3

Q17
D15
B C29
VD
DAN202K VD 473Z/16V

RT1N141C
IC1
1

E
RXD-LCC R15 1 8 C6
CNA-8 Xin VDD
4.7k 2 Xout S0 7
1-3D 473Z/16V
C

Q18 3 S1 FSOUT 6
2-2A 4 5
LF VSS
B /RXD
FS781 IC2
R22 HD64F3644H
3 RT1N141C
VD 3.3k
E

/DSR-LCC R47 C10

CNA-10
4.7k VD 1
103Z/50V NO ASSEMBLY PB1/AN
C

Q16 2 PB0/AN
1-2C 2-2A
1

3 AVss
D10 B 4
DSR TEST_SW TEST
5 X2
6 X1
DAP202K 7 Vss
RT1N141C X1 R29 0J
1 8 OSC1
NO ASSEMBLY R31 0J 9
3

OSC2
2 R30 1-3C /RES 10 RES
2-3A FVpp 11 P90/FV
VD 3 1MJ 12 P91
2-1B LED_K 13 P92
+5V(VD) CSTS0737MG03 14 P93
CNF-6
2-3C KAKITEI 15 P94
16 IRQ0
+5VR R21 220J(1/4W)
CNC-24

+5V

+5V VD VD
CNB-1
+5V
CNB-2
+5V JP3 +5V
CNC-19
+5V
CNC-20
+5V
CNC-21 R42 R41
+5V NO ASSEMBLY R38
CNC-22
+5V 10k 4.7k 4.7k
CNC-23
+5V IC3
CNE-1
+5V L3 1 8
CNA-5 A0 Vcc
2 MMZ1608S121AT 2
3
A1 WP
7
6 R39 0J
A3 SCL R40 0J
C27 + C28 4 5
Vss SDA
47uF/35V 473Z/16V CAT24WC04
GND2 L2
CNA-6
MMZ1608S121AT
GND2
CNB-5
GND2
CNB-6
GND2
CNC-7
GND2 JP2 GND2 C13 C14
CNC-8
GND2
CNC-9 222Z/50V 473Z/16V
GND2
CNC-10
GND2
CNC-11
GND2
CNC-12
GND2
CND-3
GND2
CND-4
GND2
CND-6
GND2
CND-7
GND2 IC5B
CND-9
GND2 BA10393F
CNE-3
GND2
CNE-4 5
+
7
6
-
GND2(VD)
CNF-10
+24V
F1
+24V ICP-N15
CNB-7

CNC-1 +24V F2
CNC-3 +24V ICP-N15
CN-A(B12B-PHDSS-B) CN-C(B24B-PHDSS-B) CN-D(B10B-PHDSS-B) CN-F(B11B-PH-K-S) CN-G(B2B-PH-K-S)
1 +24V
N.C.
1 2 GND1
3 4 N.C.
+24V
+24V
1 2 LPFCL
3 4 LTCL
+24V(LOSW) 1 2 +24V(LOSW)
GND2 3 4 GND2
MD
/RES
1
2
+24V
LED-M
1
2
+24V +5V 5 6 GND2 LPSL(24V) 5 6 GND1 +24V(LLSW) 5 6 GND2 /RXD 3
CND-8 TXD-LCC 7 8 RXD-LCC GND2 7 8 GND2 GND2 7 8 +24V /TXD 4 NO ASSEMBLY
CNB-10 +24V
+24V /DTR-LCC 9 10 /DSR-LCC GND2 9 10 GND2 GND2 9 10 +24V N.C. 5
CNG-1 RES-LCC 11 12 /TRC-LCC GND2 11 12 GND2 +5V(VD) 6
+24V
CNA-1 /LUD 13 14 /LPED CN-E(B14B-PHDSS-B) FVpp 7
/LTD 15 16 LTOD +5V 1 2 LCD RES 8
CN-B(B8B-PH-K-S) EXIN1 17 18 EXIN2 GND2 3 4 GND2 TXD 9
C30 + C31
+5V 1 +5V 19 20 +5V LLM 5 6 N.C. GND2(VD) 10
47uF/35V 223Z/50V +5V 2 +5V 21 22 +5V LLM(GND) 7 8 N.C. TEST 11
LRE 3 +5V 23 24 +5VR LTM-CLK 9 10 LTM-T
GND1 LLD 4 LTM 11 12 GND1
CNA-2 GND2 5 GND1 13 14 +24V(LOSW)
CNC-6 GND1 GND2 6
CNE-12 GND1 +24V 7
CNE-13 GND1 LTLSL 8

A B C

AR-LC6 CIRCUIT DIAGRAM / 回路図 3 - 1

 C D E
VD +5V

1/2
R13
4.7k R74 R5 R4 R36 R35
10k 4.7k 10k 10k 10k

R64 10k /LCD

CNE-2
R9 10k /LPED
CNC-14
R11 10k /LUD
CNC-13
R12 10k LLD
CNB-4 4
LRE
CNB-3

C
Q4
C38 C3 C2 C19 C18
C7 B
222Z/50V x5
222Z/50V

RT1N141C LTM
CNE-11

C
Q19
B

+5V
RT1N141C

E
1-4B
/TRC D1
C15

3
473Z/16V
R26 R73 R34 R25 R24
10k 10k 10k 10k 10k

DAN202K

2
R10 10k EXIN1
CNC-17
R14 10k /LTD
CNC-15
R63 10k LTM-T
1-3B CNE-10
/RXD
R33 10k LTOD
CNC-16
R28 10k EXIN2
3644H CNC-18
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49

3
PB2/AN2
PB3/AN3
PB4/AN4
PB5/AN5
PB6/AN6
PB7/AN7
AVcc
P17/IRQ3/TRGV
P16/IRQ2
P15/IRQ1
P14/PWM
P10/TMOW
P30/SCK1
P31/SI1
P32/SO1
P22/TXD

222Z/50V x5 C16

2
1-4B C37 C17 C12 C11
48 D4
PB1/AN1 P21/RXD /TXD
PB0/AN0 P20/SCK3 47
AVss P87 46
45 1-4C
TEST P86/FTID DTR
X2 P85/FTIC 44 DAP202K
43

3
X1 P84/FTIB +24VM
Vss P83/FTIA 42 LOSW 2-4C
41 LTMCLK
OSC1 P82/FTOB LLSW CNE-9
OSC2 P81/FTOA 40

C
RES P80/FTCI 39 Q20
P90/FVpp P77 38
P91 P76/TMOV 37 B
P92 P75/TMCIV 36
VD
P55/INT5/ADTRG

P93 P74/TMRIV 35
P56/INT6/TMIB

P94 P73 34
33 RT1N141C
IRQ0 Vcc

E
P50/INT0
P51/INT1
P52/INT2
P53/INT3
P54/INT4

P57/INT7
P60
P61
P62
P63
P64
P65
P66
P67

JP1 VD

C8 C1 +
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32

473Z/16V 47uF L1
/35V MMZ1608S121AT

NO ASSEMBLY
1-3B
DSR

2
2-2D
LLM_A

+24V

F3 ICP-N20

R62
2.4kJ(1/4W)

R61 TR4
2SB1240
1.5KJ(1/2W)
LPSL(24V)
CNC-5

R48
D7
1.5KJ(1/2W)
1SR153-400

+24V

ZD5
RD22FB

1
IC4
1 16 LTCL
I1 O1 CNC-4
2 O2 15
I2
3 14 LPFCL
I3 O3 CNC-2
4 13 LTLSL
I4 O4 CNB-8
2-2D LLM_B 5 12 2-3D
I5 O5 LLM_C
6 11 LED-M
I6 O6 CNG-2
7 O7 10
I7
8 9
GND COM
TD62003AP

C D E

AR-LC6 CIRCUIT DIAGRAM / 回路図 3 - 2

 A B C

MAIN PWB
+24V

F4
ICP-N15

R53
2.4KJ(1/2W)

TR3
1-3C
FVpp 2SD1768S VD

TR1

FVpp 2SB1240
CNF-7
R44
10k
C23 C22 ZD4
RD13EB1
222Z/50V 222Z/50V NO ASSEMBLY
C21

473Z/16V TR2

C
2SB1240 Q10

VD
RT1N141C

E
VD
3
VD R45

10KJ 10KJ
R37
3

C
Q8
D5
DAP202K B

C
R52
Q9
10k
C20 + B
RT1N141C
1

47uF/35V
E

R51 R50 RT1N141C

E
10k 10k

1-3C

TEST_SW

VD

2 CNF-1
MD
R7
10KJ
C

Q1

/RXD VD
1-3B
CNF-3 /RXD RT1N141C
E

RES 1-4B VD
CNF-8 RES
R46
/RES 1-3C 220J (1/4W)
CNF-2 /RES

VD R8
/TXD 1-4B
CNF-4 /TXD 10KJ
C

Q2

TXD LED1 NO ASSEMBLY B

1-4B
CNF-9 TXD
LED

R43
C

RT1N141C Q3
10k
E

B
C

Q11

1 B LED_K
1-3C
RT1N141C
E

RT1N141C
E

A B C

AR-LC6 CIRCUIT DIAGRAM / 回路図 3 - 3

 C D E

2/2
+24V(LOSW)
CNE-14
+24V
+24V(LOSW)
CND-1

C
Q5

B R18 10KJ ZD1 +24V(LOSW)

CND-2

HZ16BP

RT1N141C
R1 10k

E
+5V R2 10k 4
R3 10k D12
1SS133

D2

3
D3
DAN202K

C
Q7

B R19 10KJ ZD2

DAN202K
HZ16BP

2
R23 10k
+24VM RT1N141C
1-3D R27 10k
LOSW
R6 10k

E
LLSW

R44
0k C9 C5 C4

C
Q6
222Z/50V x 3
B R20 10KJ ZD3

HZ16BP
D11
1-2C RT1N141C
KAKITEI 1SS133

E
VD
3
PS1 RXE110 +24V(LLSW)
CND-5

R49

E
Q13
10k

C36 +
1-1D R60 2.4KJ(1/4W) R59 2.4KJ(1/4W) B
LLM_C 100uF/35V

2SB1431

LLM
C

SW1 CNE-5

2 R69
2.4kJ(1/4W)
3

T3B-SQ / JM-2W-96

R68
2.4kJ(1/4W) LLM(GND)
CNE-7
C

Q12

B
2
C

+5V +5V
Q21

1-2C B
LLM_A

C33 2SD2162 R56

E

2.4k
RT1N141C 683K/50V
TEST
8
E

CNF-11 IC5A
3
+ 1
R54 100 2 BA10393
R58 100J D6 1-1C
LLM_B
C26
1SS133
4

473Z/16V
C24 R67
R57 15kF
103Z/50V 0.22 (1W)
C32
C25 R55
510 473Z/16V
473K/50V

C D E

AR-LC6 CIRCUIT DIAGRAM / 回路図 3 - 4

LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.

Example:

<Solder composition code of lead-free solder>

Solder composition Solder composition Solder composition code

code (Refer to the Sn-Ag-Cu a
Lead-Free table at the right.)
Sn-Ag-Bi
b
Sn-Ag-Bi-Cu
Sn-Zn-Bi z
5mm
a Sn-In-Ag-Bi
Sn-Cu-Ni
Sn-Ag-Sb
n
i

s
Bi-Sn-Ag-P p
Bi-Sn-Ag

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD

When repairing a lead-free solder PWB, use lead-free solder thread.
Never use conventional lead solder thread, which may cause a breakdown or an accident.
Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-use
soldering iron is recommendable.

(2) NOTE FOR SOLDERING WORK

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity is
inferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceed
the heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering is
confirmed.
Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.
If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip after
completion of soldering work.
If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.




  
  !"#$%&'()*+
 ,-(./012
 345

a
b
5mm z
i
n
s
p

 
 

  6789:;<=
> ?@ :
AB> 89 C1DE)FGHIJGK;L,M ?D @ :

> NO> FMP QR STU-VW X Y?Z[

   

 NOLP \\R S AB FMP QR STU--  ];^L_`[  Yabc)deLf)DM

L CghijI klmnopqrst^L,`[  d=uvwx`bO  YVWj@ :

  yz{L|rU-VW U}~L€I  YU[)‚ƒ „…†„ ZUD‡@ :

 U})ˆ3 L‰‡-
 -Š‹)=Œ`[  67Ž U}@ :
 67b)U}L‘@’“`b %”•`–—V˜IM U}@ :
 CAUTION FOR BATTERY REPLACEMENT
(Danish) ADVARSEL !
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English) Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to manufacturer’s instructions.
(Finnish) VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French) ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
(Swedish) VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German) Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.

CAUTION FOR BATTERY DISPOSAL

(For USA, CANADA)

"BATTERY DISPOSAL"
THIS PRODUCT CONTAINS A LITHIUM PRIMARY
(MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY
THAT MUST BE DISPOSED OF PROPERLY. REMOVE THE
BATTERY FROM THE PRODUCT AND CONTACT YOUR
LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATION
ON RECYCLING AND DISPOSAL OPTIONS.

"TRAITEMENT DES PILES USAGÉES"

CE PRODUIT CONTIENT UNE PILE DE SAUVEGARDE DE
MÉMOIRE LITHIUM PRIMAIRE (DIOXYDE DE MANGANÈSE)
QUI DOIT ÊTRE TRAITÉE CORRECTEMENT. ENLEVEZ LA
PILE DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE
AGENCE ENVIRONNEMENTALE LOCALE POUR DES
INFORMATIONS SUR LES MÉTHODES DE RECYCLAGE ET
DE TRAITEMENT.
 All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted,
in any form or by any means,
electronic; mechanical; photocopying; recording or otherwise
without prior written permission of the publisher.

Trademark acknowledgements
• Microsoft® Windows® operating system is a trademark or copyright of Microsoft
Corporation in the U.S.A. and other countries.
• Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000,
and Windows® XP are trademarks or copyrights of Microsoft Corporation in the
U.S.A. and other countries.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• Acrobat® Reader Copyright® 1987- 2002 Adobe Systems Incorporated. All rights
reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of
Adobe Systems Incorporated.
• All other trademarks and copyrights are the property of their respective owners.

SHARP CORPORATION
Digital Document System Group
Products Quality Assurance Department
Yamatokoriyama, Nara 639-1186, Japan
2003 November Printed in Japan