See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/274775453

LabVIEW Interactive Simulations for Electromagnetic Compatibility

Article  in  International Journal of Online Engineering (iJOE) · May 2012

DOI: 10.3991/ijoe.v8i2.1935

CITATIONS READS

5 1,831

3 authors:

Eduard Lunca Silviu Ursache

Gheorghe Asachi Technical University of Iasi Gheorghe Asachi Technical University of Iasi
64 PUBLICATIONS   196 CITATIONS    20 PUBLICATIONS   56 CITATIONS   

SEE PROFILE SEE PROFILE

Alexandru Salceanu
Gheorghe Asachi Technical University of Iasi
121 PUBLICATIONS   379 CITATIONS   

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

Doctoral Thesis supervised by myself View project

All content following this page was uploaded by Eduard Lunca on 23 June 2015.

The user has requested enhancement of the downloaded file.

 PAPER
LABVIEW INTERACTIVE SIMULATIONS FOR ELECTROMAGNETIC COMPATIBILITY

LabVIEW Interactive Simulations for

Electromagnetic Compatibility
http://dx.doi.org/10.3991/ijoe.v8i2.1935

E. LUNCA, S. URSACHE and A. SALCEANU

Technical University of Iasi, Romania

Abstract—At university level, virtual instrumentation tech-  existence of dedicated modules and toolkits, such as
niques are extensively used for both education and research Control Design and Simulation Module, Simulation
in various fields of electrical engineering (EE). In this Interface Toolkit (connects LabVIEW user interfaces
paper, we illustrate the possibility of using a virtual instru- with simulation models running in Simulink), Spec-
mentation approach focused on LabVIEW to create interac- tral Measurements Toolkit and Modulation Toolkit,
tive simulations for Electromagnetic Compatibility (EMC). which can extend the basic functionality of Lab-
Firstly, the main reasons for adopting the LabVIEW VIEW to develop virtual instruments concerning
graphical programming to develop such tools are given. EMC and EMC-related topics;
Then, a number of specific modules are presented.
 possibility to create executable applications with the
Index Terms—simulations, virtual instruments, LabVIEW, LabVIEW Application Builder and to run them on
electromagnetic compatibility. any computer using the LabVIEW Run-Time Engine,
a small standalone program that can be downloaded
from the NI website.
I. INTRODUCTION
It is also worthwhile to mention that, since the Lab-
During the past two decades, LabVIEW – a fully- VIEW built-in Web Server allows controlling any VI front
featured graphical programming language from National panel directly from a web browser, an on-line experience
Instruments – has been used by millions of engineers and for EMC can be achieved in just a few simple steps. As in
scientists to develop sophisticated measurement, test and the case of Java applets, running a LabVIEW program
control systems. It eliminates a lot of the syntactical over the Internet will require client computers to have
details associated with text-based languages, while deliv- installed only LabVIEW Run-Time Engine.
ering extensive data acquisition, analysis and presentation
in a single environment. II. READY-TO-USE LABVIEW EXAMPLES FOR EMC
In academia, LabVIEW has capabilities to easy inte- LabVIEW integrates hundreds of example VIs that can
grate with the leading tools used both in research and be used for performing different types of EE experiments.
education [1-5]. Thanks to its advanced simulation capa- FFT and Frequency Analysis, Distortion Measurements,
bility and intuitive interfaces, LabVIEW allows conduct- Time-Domain Analysis and Filtering are popular catego-
ing realistic EE experiments even if there is no access to ries of built-in VIs that may serve as demonstrative mod-
real equipment [6-9]. For such a reason, we decided to use els for illustrating EMC-related concepts, such as spectral
LabVIEW for building simulation models intended to content of signals, spectral measurements, THD and
illustrate EMC concepts. Certainly, this is not a usual SINAD measurements, noise waveforms and PS density,
approach, but, with minimum cost and programming etc. Note that most of these programs are simulations.
efforts, an interactive experience based on “virtual instru-
ments” (VIs) may greatly reinforce the EMC theory.
Among others, the benefits of using LabVIEW to de-
velop computer simulations for EMC include:
 possibility to build accurate mathematical models
describing various phenomena and systems;
 attractive graphical user interfaces (GUIs), which
allow users to fully interact with the simulated
phenomena;
 reduced development time and complexity due to
configurable Express VIs and ready-to-use example
VIs;
 easy update with new requirements and develop-
ments;
 scientific visualization capability including special-
ized plots and graphs (Smith, Bode, polar, 3D curve
graphs, etc.); Figure 1. Simulation LabVIEW program for interactive
RF impedance matching [10]

iJOE – Volume 8, Issue 2, May 2012 11

 PAPER
LABVIEW INTERACTIVE SIMULATIONS FOR ELECTROMAGNETIC COMPATIBILITY

However, using LabVIEW to explore specific EMC

concepts requires developing our own code. Even if there
are a huge number of examples available on the NI web-
site, only a few of them are intended to explore EMC
concepts. Figure 1 presents the front panel of such a
program, which utilizes a Smith chart to match imped-
ances of a common LCLC circuit. The component pa-
rameters are set interactively and the resulting impedance
circles are shown instantaneously [10].

III. DEVELOPING LABVIEW SIMULATIONS FOR EMC

In order to reinforce the EMC theory, a series of Lab-
VIEW interactive simulations have been created by the
authors to illustrate EMC and EMC-related topics, includ-
ing: simple spectrum analyzer based on Zoom FFT, ana-
log modulations (AM, FM), PCB impedance control, (a)
lossless transmission line behavior, polarization of elec-
tromagnetic waves, field-strength and power estimation
(in far field conditions), radiation properties of arbitrary
length dipole antenna, radiation properties of antenna
arrays, radiation properties of aperture antennas (open
ended rectangular waveguide), electromagnetic radiation
from uniform apertures (rectangular and circular), elec-
tromagnetic radiation from straight interconnect cables,
etc. Some of these achievements will be presented in the
following, whereas a few others have been reported in a
prior work [11].
A. Using Express VIs to develop simple models.
Case study: Amplitude Modulation
As stated earlier in this paper, LabVIEW integrates con-
figuration-based Express VIs for measurement analysis
and signal processing. By requiring little or no program- (b)
ming, they may greatly reduce the development time and
complexity associated with adding analysis and signal Figure 2. Virtual instrument for simulating the amplitude modulation:
processing algorithms into applications. For instance, a (a) block diagram; (b) front panel
virtual instrument intended to explore the amplitude
modulation – important principle helping students to As illustrated in Figure 2.a, the described mathematical
understand the way in which the electromagnetic energy is model can be simply implemented in LabVIEW by using
transmitted – can be developed in just a few steps, by three “Simulate Signal” Express VIs, configured with
following the simple approach given below. adequate information of amplitude, frequency and phase,
and having the outputs added together, according to the
Let’s consider the analytical expression of an amplitude equation (2). Furthermore, a “Spectral Measurements”
modulated signal: Express VI computes the spectrum of the synthesized AM
y (t )  Ac (1  m cos  m t ) cos c t , (1) signal and displays the results in terms of peak value.
where Ac and ωc are parameters of the carrier signal, ωm is The graphical user interface in Figure 2.b allows ex-
the frequency of the modulating signal and m is the modu- ploring the AM modulation by adjusting all parameters of
lation index. the mathematical model through either knob or numeric
Starting with this equation, y(t) can be trigonometrically controls. For example, the actual measurement screen
manipulated into the equivalent form: corresponds to a modulation index of 1, which is the
maximum value allowed in the AM transmission systems;
mAc varying m beyond this value will enable users to observe
y (t )  Ac cos c t  cos(c  m )t 
2 the overmodulation condition that, in telecommunications,
, (2) should be usually avoided because of its attendant distor-
mAc
 cos(c  m )t tion and interference problems.
2
which indicates that the amplitude modulated signal has B. Exploring the lossless transmission line behavior
three components. First of them has the same frequency as An understanding of the transmission line theory is es-
the unmodulated carrier, the second component has a sential not only in the RF communications and digital
frequency equal to the sum of the carrier frequency and circuit design, but also in the Electromagnetic Compatibil-
the modulation frequency, c  m , while the third ity. It provides a link between circuit analysis and elec-
component has a frequency equal to the difference be- tromagnetics.
tween the carrier frequency and the modulation frequency, Figure 3 presents a LabVIEW simulation tool, which is
c  m . designed to analyze the behavior of a lossless transmis-
sion line connected between a generator and a load.

12 http://www.i-joe.org
 PAPER
LABVIEW INTERACTIVE SIMULATIONS FOR ELECTROMAGNETIC COMPATIBILITY

As it can easily be seen in the “parameter display area”,

the phasorial quantities are reported in both rectangular
and polar form. Note that, in the case of the polar repre-
sentation (which implies magnitude and phase informa-
tion), the phase angle is expressed in both radians and
degrees.
Finally, the voltage and current standing wave patterns
are also displayed on the two graphs located under the TL
set-up. They provide the top envelopes that bound the
time-oscillations of the voltage and current along the line
or, in other words, the maximum values that the voltage
and current can establish at each location of the TL for a
given load and generator, because of the interference
between the incident and reflected wave. For voltage, the
distance of first maximum and distance of first minimum
(from the load) are indicated under the correspondent
graph, both as a function of λ and in units of m.
Generally, this simulation tool can be used to quickly
solve various problems related to the lossless TL or to
illustrate fundamental TL concepts, such as impedance
matching, standing (stationary) waves, power flow on
Figure 3. Simulation tool for studying the behavior of the lossless line, etc. Comparisons to other sources have
lossless transmission line showed that it produces very accurate results – the output
data and standing wave patterns associated with various
Basically, it computes a series of parameters associated transmission line configurations are identical to those
with the sinusoidal excitation of the transmission line (TL) produced by some JAVA applets or those given in text-
and plots the voltage and current standing wave patterns books [12, 13].
along the TL. The line is assumed to have the arrangement
and coordinate system presented in the upper right side of C. RF radiation from uniform apertures
the graphical user interface, with the cursor position A simulation program for investigating the electromag-
varying between 0 (at the load) and L (at the source). netic radiation from uniform rectangular and circular
The input data are introduced through the three tabs lo- apertures is shown in Figure 4. The polar angle conven-
cated in the upper left side of the GUI, as following: tions assumed for this VI are depicted in the upper left
side of the GUI, with the origin being placed in the middle
 Load – allows specifying the complex impedance of of the aperture.
the load ZL;
In the case of the rectangular aperture, the program
 Source – allows specifying the complex source volt- plots the E-field strength pattern along the two principal
age US and complex source impedance ZS; planes, xz (Φ = 0°) and yz (Φ = 90°), as a function of the
 Transmission line – allows specifying the character- geometrical dimensions of the aperture, a(λ) and b(λ).
istic impedance of the line Z0, frequency f, relative Dictated by the sinc function properties, these representa-
dielectric constant of the material between the con- tions will have narrower main beams, as well as narrower
ductors εr and line length L (as a function of wave- side lobes, as the aperture size is increased. The particular
length λ). pattern in Figure 4 (front window) corresponds to a = 8λ
and b = 4λ, and features an obvious x-y dissimilarity.
Based on these data and – where appropriate – on the
actual position of the cursor (d), the program interactively In the case of the circular aperture, the program plots
displays the following TL parameters: the E-field strength pattern along the two principal planes
as a function of the aperture radius, a(λ). Since this pattern
 voltage standing wave ratio, VSWR; is described by the Bessel function of the first kind of
 voltage reflection coefficient at the load, ΓR; order 1, it is simply computed by using the Bessel Func-
 generalized reflection coefficient, Γ(d) (for the cursor tion Jv VI included in the Full Development System. As
position d = 0, this parameter is equal to ΓR); expected from theory, for large circular apertures, the xy-
 input impedance to the line, Zin; and xz-plane patterns are very similar. In other words, the
correspondent 3D representation, which may be obtained
 impedance along the line, Z(d) (for the cursor posi- by mentally putting these graphs together, features a fairly
tion d = L, this parameter is equal to Zin); symmetrical beam. The particular pattern in Figure 4
 admittance along the line, Y(d); (back window) corresponds to a = 3λ and consists of a
 amplitude of the incident voltage wave, V+; narrow main lobe, directed towards the forward direction
 voltage along the line, V(d); θ = 0°, and a few side lobes.
In addition to this program, a version that computes the
 current along the line, I(d);
radiation patterns of the two apertures in polar coordinates
 time-average power, including total power from has also been developed. For instance, Figure 5 presents
source, power absorbed by the source impedance; in- the principal patterns for the rectangular aperture of size a
jected power, power reflected by load and power ab- = 3λ and b = 2λ. And this time, the results produced with
sorbed by load. both programs are consistent with those obtained from
other reference sources [14, 15].

iJOE – Volume 8, Issue 2, May 2012 13

 PAPER
LABVIEW INTERACTIVE SIMULATIONS FOR ELECTROMAGNETIC COMPATIBILITY

REFERENCES
[1] Y. Ugurlu, “Measuring the Impact of Virtual Instrumentation for
Teaching and Research”, 2011 IEEE Global Engineering Educa-
tion Conference (EDUCON) – “Learning Environments and Eco-
systems in Engineering Education”, 2011, pp. 152-158.
[2] Tutorial “Advantages of Using LabVIEW in Academic Research”,
available online at the address http://zone.ni.com/devzone/
cda/tut/p/id/8534.
[3] A. Odon, Z. Krawiecki, “Using LabVIEW for Computer Model-
ling of Conversion Methods in Analog to Digital Converters”, 12th
IMEKO TC1 & TC7 Joint Symposium on Man Science &
Measurement, 2008, pp. 395-400.
[4] A.N. D’Andrea, F. Giannetti, G. Manara, M. Michelini, P. Nepa,
“Educational Set-Up for Microwave Laboratory Activities Using
Virtual Instruments and Real Data”, in Microwave Review, Vol.
13, No. 2, 2007, pp. 12-17.
[5] L. Sevgi, C. Uluisik, “A Labview-Based Virtual Instrument for
Engineering Education: A Numerical Fourier Transform Tool”, in
Turkish Journal of Electrical Engineering & Computer Sciences,
Vol. 14, No. 1, 2006, pp. 129-152.
[6] N.K. Swain, J.A. Anderson, “Study of Electrical Power Systems
Figure 4. Simulation program for studying the RF radiation from Using LabVIEW Virtual Instruments (VI) Modules”, IAJC-IJME
uniform apertures International Conference, 2008.
[7] M. Usama Sardar, “Synchronous Generator Simulation Using
LabVIEW”, Proceedings of World Academy of Science, Engi-
neering & Technology (WASET), Vol. 29, 2008, pp. 392-400.
[8] C. Fosalau, L. Nita, M. Antoniu, “Virtual instrument for digital
signal processing learning”, 3rd International Conference on Elec-
trical and Power Engineering, 2006.
[9] E. Brenner, “Virtual Instruments for the Circuit Analysis with
Interactive Parameter Modification”, in International Journal of
Online Engineering (iJOE), Vol. 2, No. 3, 2006.
[10] Example program “Impedance Matching using Smith Charts”,
available online at the address http://zone.ni.com/devzone/
cda/epd/p/id/3604.
[11] E. Lunca, A. Salceanu, “Virtual Instrumentation Approach for
Teaching EMC Concepts”, in Electronics and Electrical Engi-
Figure 5. The radiation pattern of the rectangular aperture neering, No. 1(117), 2012, pp. 75-80.
in polar coordinates (a = 3λ and b = 2λ) [12] Interactive Java applets available online at the address
http://www.amanogawa.com/archive/transmissionA.html.
[13] F.T. Ulaby, Fundamentals of Applied Electromagnetics (5th
IV. CONCLUSIONS AND FUTURE WORK Edition), Prentice Hall, 2006.
[14] Interactive Java applets available online at the address
This paper has shown that using LabVIEW is feasible http://www.analyzemath.com/antenna_tutorials/aperture_antennas.
to develop inexpensive, feature-rich simulation tools for html.
exploring various EMC and EMC-related concepts. Be- [15] N.K. Nikolova, “Modern Antennas in Wireless Telecommunica-
cause of their intuitive and interactive nature, the Lab- tions”, Course available online at the address
VIEW VIs may provide students or anyone interested in http://www.ece.mcmaster.ca/faculty/nikolova/antennas.htm.
the EMC area with a truly “realistic virtual experience”
prior, or in addition, to any hands-on training. AUTHORS
Our long-term interest is to enhance and extend this Eduard Lunca is a lecturer with the Electrical Meas-
work in order to provide a more complex and effective urements Department, Faculty of Electrical Engineering,
EMC learning environment. Feedback from other teachers Iasi, Romania ([email protected]).
and researchers is welcome as it can lead to further im- Silviu Ursache is a teaching assistant with the Electri-
provements and developments of these tools. Note, only a cal Measurements Department, Faculty of Electrical
part of them have been presented here. Engineering, Iasi, Romania ([email protected]).
Alexandru Salceanu is a full professor with the Elec-
ACKNOWLEDGMENT
trical Measurements Department, Faculty of Electrical
This paper was supported by the project PERFORM- Engineering, Iasi, Romania. At the moment, he is the dean
ERA “Postdoctoral Performance for Integration in the of this faculty ([email protected]).
European Research Area” (ID-57649), financed by the
European Social Fund and the Romanian Government. Received 16 January 2012. Published as submitted by the authors 27
April 2012.

14 http://www.i-joe.org

View publication stats