Scribd
Upload
81 views2 pages

Thrusters

Thrusters are maneuvering devices used on ships to provide side thrust or 360 degree thrust. There are three main types of thrusters: lateral/tunnel thrusters with a propeller installed in an athwartship tunnel, jet thrusters which take suction from below the keel and discharge to either side, and azimuthal thrusters which can rotate through 360 degrees. Thrusters enhance maneuverability, provide redundancy to main propulsion, and allow for modified ship designs with increased efficiency.

Uploaded by

João Lucas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
81 views2 pages

Thrusters

Thrusters are maneuvering devices used on ships to provide side thrust or 360 degree thrust. There are three main types of thrusters: lateral/tunnel thrusters with a propeller installed in an athwartship tunnel, jet thrusters which take suction from below the keel and discharge to either side, and azimuthal thrusters which can rotate through 360 degrees. Thrusters enhance maneuverability, provide redundancy to main propulsion, and allow for modified ship designs with increased efficiency.

Uploaded by

João Lucas
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 2

Thrusters

Manoeuvering devices designed to deliver side thrust or thrust through 360°. Thrusters are used to
allow ships to be more independent from tugs, give them more manoeuvrability for special tasks, and
in some cases give them a “take home” capability. There are three general types of thrust devices:
the lateral thruster or tunnel thruster, which consists of a propeller installed in a athwartship tunnel; a
jet thruster which consists of a pump taking suction from the keel and discharge to either side; and
azimuthal thruster, which can be rotated through 360°. A cycloidal propulsor can be considered a
type of azimuthal thruster.

Thrusters can enhance the manoeuverability of existing vessels, particularly at low speeds, and
provide a high level of redundancy. The main propulsion system based on thrusters can also provide
increased speed, or lower installed power and reduction in fuel consumption. The general
arrangement and hull form of new buildings incorporating thrusters can be modified significantly in
order to increase hydrodynamic efficiency. The other key advantage of thrusters is that they tend to
suffer less from vibration and noise and are therefore well suited for use on passenger vessels. Since
thrusters are steerable, using them may also eliminate the ship rudder.

- Azimuthing thruster – A propeller that can be rotated through 360° in the horizontal plane, thus
allowing the thrust to be generated in any desired direction.

- Continuous duty thruster – A thruster designed for continuous operation, such as dynamic
positioning thrusters, propulsion assistance, or main propulsion units.

- CRP thruster – An azimuthing thruster equipped with twin contra-rotating propellers.

- Intermittent duty thruster – A thruster which is designed for the operation at the peak power or rpm
levels, or both, for periods not exceeding 1 hour followed by periods at the continuous rating of less,
with total running time not exceeding 8 hours in 20 hours. Generally, such thrusters are not meant to
operate for more than 1000 hours per year.

- Jet thruster – A pump arranged to take suction from beneath or close to the keel and to discharge to
either side, to develop port or starboard thrust, or in many cases through 360°.

- Lateral thruster, transverse thruster, tunnel thruster – A propulsion device fitted to certain types of
ships to improve manoeuvrability. The thrust unit consists of a propeller mounted in an athwartships
tunnel and provided with some auxiliary drive such as an electric or hydraulic motor. During
operation, the water is forced through the tunnel to push the ship sideways either to port or starboard
as required. This type of thruster is usually installed at the bow (bow thruster), and sometimes at the
stern (stern thruster).
- Outboard thruster – In operation the stern-mounted outboard thruster is similar to an outboard
engine on a speedboat, and is capable of being lifted out of the water for easy maintenance and to
reduce drag while underway.

- Retractable thruster – A thruster able to be pulled up or in. A thruster able to be pulled up or in to


reduce drag when vessel is in a transit mode, or reduce depth of vessel when transiting or operating
in shallow water.

- Rim drive thruster – A revolutionary compact lateral thruster developed by two partnerships: Rolls-
Royce with Smartmotor from Trondheim, and Van der Velden® Marine Systems with Combimac (The
Netherlands). The electrical motor has the form of a thin ring. Its stator is incorporated in the tunnel
and its rotor carries propeller blades. Waterflow through the unit is unobstructed since there is no
gearbox in the tunnel, nor are struts needed to support a hub. Together these factors give a high total
efficiency and reduced noise and vibration.

- Swing-up azimuth thruster – A dual-function unit, supplementing an azimuthing function with a


tunnel thruster role when the unit is in the raised position and recessed within the hull. The transverse
tunnel-shaped recess is oversized to allow the thruster to rotate through 180° to provide thrust to port
or to starboard. In this way, the propeller thrust is always in the same direction and therefore, the
propeller blades can be designed with optimum camber and radial pitch distribution.

- Titled thruster – Wärtsilä developed new type of steerable thruster with a downward tilted propeller
shaft. The 82° gearbox deflects the jet sufficiently downward to minimize hull-interaction effects, thus
improving thruster efficiency.

You might also like