OWNER’S MANUAL

Wireless
Sound Bar
Please read this manual carefully before operating your set and retain it for future
reference.

MODEL
SL6Y (SL6Y, SPL5B-W)

www.lg.com
1901_Rev01 Copyright © 2019 LG Electronics Inc. All Rights Reserved.
 2 Getting Started

Safety Information NOTICE: For safety marking information including

product identification and supply ratings, please refer
to the main label on the bottom or the other surface
of the product.
CAUTION
1 RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION concerning the Power Cord
Getting Started

The Power Plug is the disconnecting device. In case

CAUTION: TO REDUCE THE RISK OF ELECTRIC of an emergency, the Power Plug must remain readily
SHOCK DO NOT REMOVE COVER (OR BACK) accessible.
NO USER-SERVICEABLE PARTS INSIDE REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL. Check the specification page of this owner’s manual
to be certain of the current requirements.
This lightning flash with arrowhead Do not overload wall outlets. Overloaded wall outlets,
symbol within an equilateral triangle loose or damaged wall outlets, extension cords, frayed
is intended to alert the user to the power cords, or damaged or cracked wire insulation
presence of uninsulated dangerous are dangerous. Any of these conditions could result
voltage within the product’s in electric shock or fire. Periodically examine the
enclosure that may be of sufficient magnitude to cord of your device, and if its appearance indicates
constitute a risk of electric shock to persons. damage or deterioration, unplug it, discontinue use of
The exclamation point within an the device, and have the cord replaced with an exact
equilateral triangle is intended replacement part by an authorized service center.
to alert the user to the presence Protect the power cord from physical or mechanical
of important operating and abuse, such as being twisted, kinked, pinched, closed
maintenance (servicing) instructions in a door, or walked upon. Pay particular attention to
in the literature accompanying the product. plugs, wall outlets, and the point where the cord exits
the device.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
confined space such as a book case or similar unit.
CAUTION: Do not use high voltage products around
this product. (ex. Electrical swatter) This product may
malfunction due to electrical shock.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled
with liquids, such as vases, should be placed on the
apparatus.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided
for ventilation and to ensure reliable operation of
the product and to protect it from over heating.
The openings should never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a built-
in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION: No naked flame sources, such as lighted
candles, should be placed on the apparatus.
 Getting Started 3

CAUTION: Only use the AC adapter supplied with OPEN SOURCE SOFTWARE NOTICE
this device. Do not use a power supply from another INFORMATION
device or another manufacturer. Using any other
power cable or power supply may cause damage to To obtain the source code under GPL, LGPL, MPL, and
other open source licenses, that is contained in this
the device and void your warranty. 1
product, please visit http://opensource.lge.com.
Symbols

Getting Started
In addition to the source code, all referred license
terms, warranty disclaimers and copyright notices are
~ Refers to alternating current (AC). available for download.
LG Electronics will also provide open source code to
0 Refers to direct current (DC). you on CD-ROM for a charge covering the cost of
performing such distribution (such as the cost of
Refers to class II equipment.
media, shipping and handling) upon email request to
1 Refers to stand-by. [email protected].
This offer is valid for a period of three years after our
! Refers to “ON” (power). last shipment of this product. This offer is valid to
anyone in receipt of this information.
Refers to dangerous voltage.
4 Table of Contents

Table of Contents

1 Getting Started 2 Connecting

2 Safety Information 15 Organizing cables (Optional)
6 Introduction 15 Connecting the AC Adapter
7 Front panel 16 Wireless subwoofer and rear speaker (Sold
8 Rear panel Separately) connection
9 Remote control 16 –  Wireless subwoofer connection
12 Installing the sound bar 17 –  Rear speakers connection (Sold
13 Mounting the main unit on a wall Separately)
18 –  Surround sound
20 –  How to Affix the Ferrite Core
21 Connecting to your TV
21 –  Using an OPTICAL cable
21 –  LG Sound Sync
23 –  Using an HDMI cable
23 –  ARC (Audio Return Channel) function
23 –  What is SIMPLINK?
24 –  Additional information for HDMI
25 Optional equipment connection
25 –  HDMI connection
26 –  OPTICAL IN connection
26 –  USB connection
26 –  Compatible USB devices
27 –  USB device requirement
27 –  Playable file
 Table of Contents 5

1
3 Operating 4 Troubleshooting
29 Basic operations 37 Troubleshooting
29 –  USB operation 37 – General
30 Other operations 38 –  NOTES to use wireless
2
30 –  Using your TV remote control 39 –  NOTES to release Demo mode
31 –  AUTO POWER On/Off
32 –  Auto function change
32 Quick Start
5 Appendix
33 Using a Bluetooth Wireless Technology 40 Trademarks and licenses 3
33 –  About Bluetooth 41 Specifications
33 –  Bluetooth profiles 43 Handling the Speaker
33 –  Listening to Music of a Bluetooth Device
35 –  Controls connected Bluetooth device
35 –  Bluetooth connection lock (BT LOCK) 4
35 Using BLUETOOTH App
35 –  Install “Music Flow Bluetooth” App onto
Your BLUETOOTH Device
36 –  Activate BLUETOOTH with “Music Flow
Bluetooth” App 5
 6 Getting Started

Introduction
Symbol used in this manual
1
,,Note
Getting Started

Indicates special notes and operating features.

>>Caution
Indicates cautions for preventing possible damages
from abuse.
 Getting Started 7

Front panel

Getting Started
A Remote sensor
Display Window
B -- Display window will be darkened automatically if there is no key input for 15 seconds.
When you press any button, the display window will brighten.
1 (Standby)
-- Switches the unit ON or OFF.
F (Function)
-- Select the function and input source by pressing F repeatedly.

Input source / Function Display

Optical
ARC OPT/HDMI ARC
C LG Sound Sync (Wired)
Bluetooth BT
LG Sound Sync (Wireless) LG TV
HDMI IN HDMI
USB USB

o/p (Volume)
-- Adjusts volume level.

, This unit will turn itself off to save electric consumption when the main unit is not connected to an external
device and is not used for 15 minutes.
 8 Getting Started

Rear panel

1
Getting Started

DC IN
A -- Connect to the AC adapter.
USB Port
B -- Connect USB memory device to the USB port on the back of the unit.
OPTICAL IN
C -- Connect the OPTICAL IN jack on the back of the unit to OPTICAL OUT jack on the TV.
HDMI IN
D -- Connect HDMI IN jack on the back of the unit to HDMI OUT jack on the external device.
You can enjoy the sound and picture from HDMI connection on an external device.
(TV ARC) HDMI OUT
E -- Connect the (TV ARC) HDMI OUT jack on the back of the unit to ARC jack on the TV.
 Getting Started 9

Remote control

Replacement of Battery 1
Remove the battery cover on the rear of the remote

Getting Started
control, and insert the battery with 4 and 5
matched correctly.

1 (Standby)
a
-- Switches the unit ON or OFF.
VOL (Volume) o/p
b
-- Adjusts speaker volume.
C/V (Skip/Search)
c -- Press C or V to go to next or previous file.
-- Press and hold C or V during playback and release it at the point you want.
N (Play/Pause)
-- Starts playback. / Pauses playback.
d yy BT (Bluetooth) connection Lock: It allows you to connect a Bluetooth device only on Bluetooth
and LG TV functions. (Page 35)
To turn on or off the Bluetooth connection lock, press and hold N for about 3 seconds and press it
again in BT (Bluetooth) function.
 10 Getting Started

SOUND EFFECT
-- Selects a sound effect mode by using SOUND EFFECT.

On Display Description
1
Analyzes the property of the input sound and provides the
ASC (Adaptive Sound Control)
Getting Started

sound optimized for the content in real time.

BASS BLAST or BASS BLAST+ Reinforces the bass and powerful sound.
STANDARD You can enjoy optimized sound.
e
DTS VIRTUAL : X You can enjoy more immersive and cinematic surround sound.

yy TV remote: It allows you to control the volume of this unit by your TV remote control even by other
company’s product. (Page 30)
To turn on or off the TV Remote function, press and hold SOUND EFFECT for about 3 seconds and
press it again.
, Supported TV brands
LG Panasonic Philips Samsung Sharp Sony Toshiba Vizio

(Sound tuning)
-- Adjusts sound level of each speaker.
Select the speaker you want to adjust by using and adjust the sound level by using VOL o/p.
, Adjusting rear speakers level is applied only when the rear speakers are connected.

Speaker Display Range

Sub Woofer WF -15 ~ 6
f
Center C -6 ~ 6
Rear R -6 ~ 6
Treble TRE -5 ~ 5
Bass BAS -5 ~ 5

yy Surround sound: It allows you to enjoy surround sound with rear speakers. (Page 18)
To turn on or off the surround sound, press and hold for about 3 seconds and press it again.

F (Function)
g
-- Select the function and input source by pressing F repeatedly.
[ (Mute)
h
-- Press [ to mute your unit. To cancel it, press [ again.
 Getting Started 11

J (Information)
-- You can display various information of the input source by pressing J.
-- OPT (Optical)/ARC/HDMI (HDMI IN) : Audio format
-- BT (Bluetooth) : Connected Bluetooth device name 1
i
-- USB : File information contained on a USB.

Getting Started
yy Auto Power ON/OFF: It allows the unit to turn on and off automatically by input signals : Optical,
LG TV or Bluetooth (Page 31)
To turn on or off AUTO POWER function, press and hold J for about 3 seconds and press it again.
REPEAT
j
-- Press REPEAT to select desired repeat or random mode.
FOLDER W/S
k
-- Searches a folder on USB device.
 12 Getting Started

Installing the sound bar >>Caution

yy For best performance of wireless connection
such as Bluetooth or wireless subwoofer,
You can hear the sound by connecting the unit to the do not install the unit on Metallic furniture
1 other device : TV, Blu-ray disc player, DVD player, etc. because wireless connection communicates
Place the unit in front of the TV and connect it to the through a module positioned on the bottom
Getting Started

device you want. (Pages 21 - 26) of the unit.

You can place the wireless subwoofer anywhere in yy Be careful not to make scratches on the
your room. But it is better to place the subwoofer surface of the Unit /Subwoofer when
near the main unit. Turn it slightly toward the center installing or moving them.
of the room to reduce the wall reflections.
For the best surround sound, place the speakers as
shown below. Installing the additional foot
You can extend the height of the unit by using
additional foot (height : 14 mm)

1. Turn the unit upside down.

2. Peel off a sticker attached to the additional foot.
Then place it on the existing foot of the unit.
3. Press the additional foot with adequate force to
get it firmly fixed.

,,Note
yy If the sound bar covers the remote sensor of
the TV, please separate distance between the
sound bar and TV by 10 ~ 15 cm or more.
yy The illustration above may differ from actual
units.
yy You can enjoy surround sound by using
Wireless Rear Speaker kit. Wireless Rear
Speakers Kit sold separately (SPK8-S).
 Getting Started 13

Mounting the main unit 1. Match the TV’s BOTTOM EDGE of Wall bracket
install guide with the bottom of TV and attach to
on a wall the position.

1
You can mount the main unit on a wall.

Getting Started
2. When you mount it on a wall (concrete), use the
wall plugs. You should drill some holes. A guide
>>Caution sheet (Wall bracket install guide) is supplied to
drill. Use the sheet to check the point to drill.
Because it is difficult to make a connection after
installing this unit, you should connect the cables
before installation.

Preparation materials
Unit

Wall bracket install guide

3. Remove the Wall bracket install guide.

Wall bracket 4. Fix the brackets with screws (A) as shown in the
illustration below.
Screws
(Not supplied)
Screws (A)

Wall plug

,,Note
Screws (A) and Wall Plugs are not supplied for
mounting the unit. We recommend the Hilti
(HUD-1 6 x 30) for the mounting.
 14 Getting Started

5. Put the unit on the brackets to match screw

holes on the bottom of the unit.

1
Getting Started

6. Fix the unit with the screws firmly.

,,Note
To detach the unit, perform it in reverse order.

>>Caution
yy Do not install this unit upside down. It can
damage the parts of this unit or be the cause
of personal injury.
yy Do not hang onto the installed unit and avoid
any impact to the unit.
yy Secure the unit firmly to the wall so that it
does not fall off. If the unit falls off, it may
result in an injury or damage to the product.
yy When the unit is installed on a wall, please
make sure that a child does not pull any of
connecting cables, as it may cause it to fall.
 Connecting 15

Organizing cables Connecting the AC

(Optional) Adapter
You can organize the cable with cable ties. Connect the speaker to the power supply with the
supplied AC adapter.
1. Hold the cables together with cable ties as shown
below. 1. Connect the supplied AC power cord to the AC
2. Tighten cable ties. adapter.
2. Connect the AC adapter cable to DC IN adapter 2
input.

Connecting
3. Plug the AC power cord into an AC outlet.

,,Note
yy After all connections are completed, you can
arrange cables as needed.
yy Cable ties are not supported.

>>Caution
Only use the AC adapter supplied with this
device. Do not use a power supply from another
device or manufacturer. Using any other power
cable or power supply may cause damage to the
device and void your warranty.
 16 Connecting

Wireless subwoofer Manually pairing wireless subwoofer

When your connection is not completed, you can
and rear speaker (Sold check red LED on the wireless subwoofer and the
wireless subwoofer does not make sound. To solve
Separately) connection the problem, follow the steps below.
1. Press Pairing on the rear of the wireless
subwoofer.
Wireless subwoofer connection
2 LED indicator of wireless subwoofer
Connecting

LED Color Status

Green The connection is trying.
(Blink) -- The green LED on the rear of the wireless
Green The connection is completed. subwoofer blinks quickly.
(If the green LED does not blink, press and hold
Red The wireless subwoofer is in the Pairing.)
standby mode or the connection
2. Turn on the sound bar.
is failed.
-- Pairing is completed. The green LED on the rear
Off (No The power cord of wireless of the wireless subwoofer turns on.
display) subwoofer is disconnected.

Setting up the wireless subwoofer for

the first time
1. Connect the power cord of the sound bar and the
wireless subwoofer to the outlet.
2. Turn on the sound bar. The sound bar and
the wireless subwoofer will be automatically
connected.
-- Green LED on the rear of wireless subwoofer
turns on.
 Connecting 17

,,Note Rear speakers connection (Sold

yy It takes a few seconds (and may take longer)
for the main unit and the subwoofer to Separately)
communicate with each other and make
sounds. Connecting the rear speakers
yy The closer the main unit and the subwoofer, 1. Connect the black stripe wire to the terminal
the better sound quality. It is recommended marked - (minus) and the other end to the
to install the main unit and the subwoofer as terminal marked + (plus).
close as possible and avoid the cases below.
-- There is an obstacle between the main unit 2
and the subwoofer.

Connecting
-- There is a device using same frequency
with this wireless connection such as
a medical equipment, a microwave or a
wireless LAN device.
-- Keep the sound bar and the subwoofer
away from the device (ex. wireless router,
microwave oven, etc.) over 1 m to prevent
wireless interference.

!1 m

2. Connect the wireless receiver and the rear

speakers (right, left) with the speaker cables.
Color Position
Grey Rear right
Blue Rear left

,,Note
You need to purchase the wireless rear speakers
kit (SPK8-S) to enjoy surround sound.
 18 Connecting

>>Caution Manually pairing wireless receiver

yy Use the speaker supplied with this unit When your connection is not completed, you can
only. Using any other speaker may cause see the red LED on the wireless receiver and rear
malfunction. speakers are not made sound. To solve the problem,
yy Be sure to match the speaker cable to the follow the below steps.
appropriate terminal on the components: +
1. Press PAIRING on the rear of the wireless
to + and – to –. If the cables are reversed, the
receiver.
sound will be distorted and will lack bass.

2
LED indicator of wireless receiver
Connecting

LED Color Status

Yellow - green
The connection is trying.
(Blink)
Yellow - green The connection is completed. -- The yellow - green LED on the wireless receiver
blinks quickly.
Red The wireless receiver is in standby
mode or the connection is failed. 2. Turn on the main unit
-- Paring is completed. The yellow - green LED on
Off The power cord of wireless the wireless receiver turns on.
(No display) receiver is disconnected.

Setting up the wireless receiver for the Surround sound

first time You can enjoy magnificent surround sound for all the
input sound source with rear speakers.
1. Connect the power cord to the wireless receiver
to the outlet. If you turn on the surround function, the whole
speaker outputs sound.
2. Turn on the main unit : The sound bar and wireless
When you turn off the surround function, the
receiver will be automatically connected.
speakers output sound as an original input sound
-- Yellow - green LED on the wireless receiver
channel.
turns on.
To turn on surround function, press and hold on
the remote control for about 3 seconds and press it
once again while “OFF - SURROUND” is scrolled.
To turn off surround function, press and hold on
the remote control for about 3 seconds and press it
once again while “ON - SURROUND” is scrolled.
 Connecting 19

Surround function ON

Output
Sound Effect Input
No rear speakers Rear speakers connected

2.0 Ch
ASC
5.1 Ch

2.0 Ch 2
STANDARD

Connecting
5.1 Ch

BASS BLAST 2.0 Ch

or
BASS BLAST + 5.1 Ch

2.0 Ch
DTS
VIRTUAL : X
5.1 Ch

Surround function OFF

Output
Sound Effect Input
No rear speakers Rear speakers connected

2.0 Ch
ASC
5.1 Ch

2.0 Ch
STANDARD
5.1 Ch

BASS BLAST 2.0 Ch

or
BASS BLAST + 5.1 Ch

2.0 Ch
DTS
VIRTUAL : X
5.1 Ch
 20 Connecting

How to Affix the Ferrite Core ,,Note

yy If there is a strong electromagnetic wave
Ferrite core may not be provided depending on each product nearby, interference may occur. Put
nation’s regulations. the main unit and wireless receiver away from
there.
Affix the Ferrite Core for speaker
yy The wireless receiver will automatically switch
cables to standby mode in a few minutes after the
You must affix a ferrite core in order to reduce or sound bar is turned off.
eliminate electrical interference. When the wireless receIver is in standby
mode, the LED will turn on in red.
2 1. Pull the stopper [a] of the ferrite core to open.
yy When you turn on the sound bar, the wireless
2. Wind the speaker cables around the ferrite core
Connecting

receiver will turn on and the LED will change

twice. to yellow - green and then the rear speakers
3. Close the ferrite core until it clicks. makes sound within a few seconds.
yy It takes a few seconds (and may take longer)
for the main unit and Wireless Receiver to
communicate with each other.
yy Use the rear speaker at least 30 cm away
from either TV screen or PC monitor.
yy When the wireless receiver is being
connected or disconnected with the main
unit, output sound may be interrupted.
yy Set the distance between the sound bar and
the wireless receiver as close as possible and
keep them away from the device (ex. wireless
router, microwave oven, etc.) over 1 m to
prevent wireless interference.

>!P
1m
 Connecting 21

Connecting to your TV LG Sound Sync

Please connect with this unit and TV using the optical

digital cable or HDMI cable considering the state of
the TV. You can control some functions of this unit by
your TV’s remote control with LG Sound Sync. It is
Using an OPTICAL cable compatible with the LG TV that is supported LG
Sound Sync. Make sure of the LG Sound Sync logo on
1. Connect the OPTICAL IN jack on the back of the your TV.
unit to OPTICAL OUT jack on the TV using an 2
Controllable function by LG TV’s remote control :
OPTICAL cable. Volume up/down, mute

Connecting
Refer to the TV’s instruction manual for the details of
LG Sound Sync.
Make one of the following connections, depending on
the capabilities of your equipment.
Optical
cable ,,Note
yy You can also use the remote control of this
unit while using LG Sound Sync. If you use TV’s
remote control again, the unit synchronizes
with the TV.
According to TV Specifications, the volume
and mute of this unit synchronize with TV.
2. Select the input source to OPT/HDMI ARC by
pressing F repeatedly. yy When the connection fails, make sure of the
condition of the TV and power.
You can see “OPT” on the display window if
connecting normally between this unit and your yy Make sure of the condition of this unit and
the connection in the cases below when using
TV.
LG Sound Sync.
,,Note -- The unit is turned off.
yy Before connecting the optical cable, be sure -- Changing the function to the others.
to remove the protection plug cover if your
cable has the cover. -- Disconnecting the optical cable.
-- Disconnecting the wireless connection
yy You can enjoy the TV audio through the
speakers of this unit. In the case of some TV caused by interference or a distance.
models, you must select the external speaker yy The amount of time to turn off this unit is
option from the TV menu. (For details, different depending on your TV when you set
reference your TV user manual.) AUTO POWER function to ON.
yy Set up the sound output of TV to listen to yy Details of TV setting menu vary depending on
the sound through this unit : the models of your TV.
TV setting menu [ [Sound] [ [TV Sound
output] [ [External speaker (Optical)]
yy Details of TV setting menu vary depending
on the manufacturers or models of your TV.
yy If this unit is connected by OPTICAL and ARC
at the same time, the ARC signal is a high
priority.
 22 Connecting

LG Sound Sync with wired connection LG Sound Sync with wireless

1. Connect your LG TV to the unit by using an
connection
optical cable. 1. Turn on the unit by pressing 1.
2. Select the LG TV function by pressing F
repeatedly.
3. Set up the sound output of TV to listen to the
Optical sound through this unit :
TV setting menu [ [Sound] [ [TV Sound
cable
2 output] [ [LG Sound Sync (Wireless)]
“PAIRED” appears on the display window for
Connecting

about 3 seconds and then you can see “LG TV”

on the display window if connecting normally
between this unit and your TV.

2. Set up the sound output of TV to listen to the ,,Note

sound through this unit : If you turned off the unit directly by pressing
TV setting menu [ [Sound] [ [TV Sound 1 (Power), LG Sound Sync (Wireless) will be
output] [ [LG Sound Sync (Optical)] disconnected.
3. Turn on the unit by pressing 1.
4. Select the input source to OPT/HDMI ARC by
pressing F repeatedly.
You can see “LGOPT” on the display window if
connecting normally between this unit and your
TV.

,,Note
Details of TV setting menu vary depending on
the models of your TV.
 Connecting 23

Using an HDMI cable ARC (Audio Return Channel)

If you connect this unit to a TV that supports HDMI function
CEC and ARC (Audio Return Channel), you can
The ARC function enables an HDMI capable TV to
enjoy the TV audio through the speakers of this unit
send the audio stream to HDMI OUT of the unit.
without connecting the optical cable.
To use this function :
1. Connect the (TV ARC) HDMI OUT jack on the
-- Your TV must support the HDMI-CEC and ARC
back of the unit to ARC jack on the TV using an
function and the HDMI-CEC and ARC must be set
HDMI cable.
to On.
-- The setting method of HDMI-CEC and ARC may 2
differ depending on the TV. For details about ARC

Connecting
function, refer to your TV manual.
-- You must use the HDMI cable (Type A, High Speed
HDMI cable HDMI™ cable with Ethernet).
-- You must connect the HDMI OUT on the unit with
HDMI IN of the TV that supports ARC function
using an HDMI cable.
-- You can connect only one Sound bar to TV
compatible with ARC.
2. Select the input source to OPT/HDMI ARC by
pressing F repeatedly.
What is SIMPLINK?
You can see “ARC” on the display window if
connecting normally between this unit and your
TV.

,,Note
yy You can enjoy the TV audio through the Some functions of this unit are controlled by the
speakers of this unit. In the case of some TV TV’s remote control when this unit and LG TV’s with
models, you must select the external speaker SIMPLINK are connected through HDMI connection.
option from the TV menu. (For details,
Controllable functions by LG TV’s remote control :
reference your TV user manual.)
Power on/off, volume up/down, etc.
yy Set up the sound output of TV to listen to Refer to the TV owner’s manual for the details of
the sound through this unit :
SIMPLINK function.
TV setting menu [ [Sound] [ [TV Sound
output] [ [External speaker (HDMI ARC)] LG TV’s with SIMPLINK function has the logo as
shown above.
yy Details of TV setting menu vary depending on
the manufacturers or models of your TV. ,,Note
yy Depending on your LG TV model, you may yy Depending on the state of the unit, some
need to turn on the SIMPLINK function on SIMPLINK operation may differ from your
your LG TV. purpose or not work.
yy When you return to ARC function from yy Depending on a TV or a player which is
another function, you need to select the input connected with this unit, SIMPLINK operation
source to OPT/HDMI ARC. Then this unit may differ from your purpose.
changes to ARC function automatically.
 24 Connecting

Additional information for HDMI HDMI cable Checklist

yy When you connect an HDMI or DVI compatible Some HDMI cables have poor signal transmission,
device make sure of the following: which can cause problems with sound and video
transmission.
- Try switching off the HDMI/DVI device and this
player. Next, switch on the HDMI/DVI device and Even after HDMI cable connections, if no sound,
leave it for around 30 seconds, then switch on sound interrupted, noise occurring from the sound
this player. bar and/or no video, no smooth video on your TV, the
HDMI cable may be the problem.
- The connected device’s video input is set
correctly for this unit. Use the cable marked with the premium HDMI
2 certification logo. Also make sure that the your
- The connected device is compatible with
using cable is a certified Type A, Ethernet high-speed
Connecting

720 x 576p (or 480p), 1280 x 720p, 1920

HDMI™ cable.
x1080i or 1920 x 1080p video input.
yy Not all HDCP-compatible HDMI or DVI devices will (X)
STANDARD HDMI CABLE WITH ETHERNET
work with this player.
- The picture will not be displayed properly with HIGH SPEED HDMI CABLE
(X)
non-HDCP device.
(O)
,,Note
HIGH SPEED HDMI CABLE WITH ETHERNET

yy If a connected HDMI device does not accept

the audio output of the player, the HDMI Connection through HDMI Cable*
device’s audio sound may be distorted or may Your television must support the newest HDMI
not output. features (HDMI CEC1) / ARC (Audio Return Channel))
yy Changing the resolution when the connection to fully enjoy the Live broadcasting channel with
has already been established may result in audio system through an HDMI cable. Unless your
malfunctions. To solve the problem, turn off TV supports these HDMI features, the audio system
the player and then turn it on again. should be connected through an OPTICAL cable.
yy When the HDMI connection with HDCP is not 1) HDMI CEC (High-Definition Multimedia Interface
verified, TV screen is changed to black screen. Consumer Electronics Control)
In this case, check the HDMI connection, or Consumer Electronics Control (CEC) is an HDMI
disconnect the HDMI cable. feature designed to allow the user to command and
yy If there are noises or lines on the screen, control the CEC-enabled devices, that are connected
please check the HDMI cable (length is through HDMI by using only one of their remote
generally limited to 4.5 m). controls.
yy You cannot change the video resolution in the * Trade names for CEC are SimpLink (LG) , Anynet+
HDMI mode. Change the video resolution of (Samsung), BRAVIA Sync (Sony), EasyLink (Philips),
the connected component. etc.
yy If the video output signal is abnormal when
your personal computer is connected to HDMI
IN jack, change the resolution of your personal
computer to 576p (or 480p), 720p, 1080i or
1080p.
 Connecting 25

Optional equipment For enjoying both sound and picture

You can enjoy both sound and picture from the
connection external device you connect.

HDMI connection
You can enjoy the sound and picture from HDMI
connection on external device.
HDMI
cable 2
For enjoying sound only

Connecting
You can enjoy the sound from the external device you
connect.

HDMI
cable

To the Blu-ray disc player,

DVD player, etc. 1. Connect HDMI IN jack on the back of the unit to
HDMI OUT jack on the external device such as
1. Connect HDMI IN jack on the back of the unit to
Blu-ray disc player, DVD player, etc.
HDMI OUT jack on the audio device such as Blu-
ray disc player, DVD player, etc. 2. Connect (TV ARC) HDMI OUT jack on the back of
the unit to HDMI IN jack on the TV.
2. Select the input source to HDMI by pressing F
repeatedly. 3. Select the input source to HDMI by pressing F
repeatedly.

,,Note
yy Audio and Video signal can't pass through
when this unit is turned off.
yy (TV ARC) HDMI OUT jack is for TV connection.
Even though multi channel is inputted to the
unit through an HDMI cable, the unit can only
output PCM 2 channel to TV.
 26 Connecting

OPTICAL IN connection USB connection

Connect an optical output jack of external devices to Connect USB memory device to the USB port on the
the OPTICAL IN jack. back of the unit.

2 Optical cable
Connecting

To the optical output

jack of external device

1. Connect the OPTICAL IN jack on the back of the

unit to optical out jack of your external device.
,,Note
It is recommended that you purchase a USB
2. Select the input source to OPT/HDMI ARC by gender separately for the convenience of USB
pressing F repeatedly. insertion and extraction. (Recommended USB
You can see “OPT” on the display window if gender type : USB 2.0 extension cable)
connecting normally between this unit and your
device.

,,Note For more information of playing files on a USB, refer

Before connecting the optical cable, be sure to to the page 29.
remove the protection plug cover if your cable
has the cover. Removing the USB Device from the unit.
1. Choose a different function/mode.
2. Remove the USB device from the unit.

Compatible USB devices

yy MP3 Player : Flash type MP3 player.
yy USB Flash Drive : Devices that support USB 2.0.
yy The USB function of this unit does not support
some USB devices.
 Connecting 27

USB device requirement Playable file

yy Devices which require additional program Sampling Frequency
installation connected to a computer, are not
MP3 : within 32 to 48 kHz
supported.
WMA : within 32 to 48 kHz
yy Do not extract the USB device while in operation. OGG : within 32 to 48 kHz
yy For a large capacity USB, it may take longer than a FLAC :32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,
few minutes to be searched. 176.4 kHz and 192 kHz (16 bit/ 24 bit)
yy To prevent data loss, back up all data. WAV : 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz,
176.4 kHz and 192 kHz (16 bit/ 24 bit)
yy This unit recognizes up to 2,000 files. 2
yy The unit’s USB Port cannot be connected to PC. Bitrate resolution

Connecting
The unit can not be used as a storage device.
MP3 : within 80 to 320 kbps
yy The exFAT file system is not supported on this WMA : within 56 to 128 kbps
unit. (FAT16/FAT32/NTFS systems are available.) OGG : within 64 to 500 kbps
yy Depending on some devices, it may not available to
recognize the followings on this unit. yy Maximum files : Up to 2,000
-- External HDD yy Maximum directories : Up to 200
-- Card readers yy A protected file by DRM (Digital rights
-- Locked devices management) cannot be played on the unit.
-- Hard type USB devices yy Video files in the USB storage device can not be
played.
-- USB hub
yy Depending on the performance of your USB
-- Using USB extension cable device, playback may not work well.
-- iPhone/iPod/iPad
-- Android device
 28 Connecting

,,Note
yy Folders and files on the USB are recognized
as below.
: Folder
: File

a C

D
2
E
Connecting

b F
G
c H
I

d J
A
B

yy If there is no file in a folder, the folder will not

appear.
yy File will be played from file $A to file $J
one by one.
yy Files will be played in order recorded and it
may be different depending on the record
circumstances.
yy This unit can display file or folder names that
contain numbers or English characters only.
yy *ROOT : The first screen you can see when a
this unit recognize the USB is “ROOT”.
 Operating 29

Basic operations ,,Note

yy The resume point may be cleared when you
pull out the power cord or removing the USB
device from the unit.
USB operation
yy Repeat/Random playback operates as follows.
1. Connect the USB device to the USB port.
2. Select the USB function by pressing F repeatedly. On Display Description
To Do this OFF Plays songs on USB device
in order.
Press N on the remote
Playback
control. ONE Plays a same song
repeatedly.
During playback, press N on
Pause
the remote control. FOLDER Plays songs in a folder
repeatedly.
During playback, press V on
3
the remote control to go to the ALL Plays all the songs on USB
next file. device repeatedly.

Operating
Playing less than 3 seconds, SHUFFLE Plays all the songs once
Skip to the next/ press C on the remote randomly, and stops the
previous file control to go to the previous playback.
file.
Playing after 3 seconds, press
C on the remote control to
go to the beginning of the file.

Press and hold C/V on the

Search for a
remote control during playback
section within a
and release it at the point you
file
want to listen to.

Press REPEAT on the remote

Play repeatedly control repeatedly. Refer to
or randomly the note for details about the
display change.

Press FOLDER W/S on the

Search a folder
remote control.
This unit memorizes a current
Resume song which is played before
playback changing the function or
turning off the unit.
 30 Operating

Other operations How to disconnect the wireless

network connection or the wireless
device
Using your TV remote control Set up the AUTO POWER ON/OFF function to off
and turn off the unit.
You can control some functions of this unit by your
TV remote control even by other company’s product.
Controllable functions are volume up/down and
mute.
Press and hold SOUND EFFECT on the remote
control for about 3 seconds. “ON - TV REMOTE”
appears and you can control this unit by your TV
remote control.
To check the status of this function, press and hold
3 SOUND EFFECT on the remote control.
To turn off this function, press and hold SOUND
Operating

EFFECT on the remote control and press it once

again while “ON - TV REMOTE” is scrolled.

,,Note
yy Make sure that the sound output of your TV
is set to [External speaker].
yy This function does not operate on LG TV’s
magic remote control.
yy This function may not work well when some
TV control functions such as HDMI CEC,
SIMPLINK and LG Sound Sync set to ON.
yy Some remote control may not be supported.
 Operating 31

AUTO POWER On/Off ,,Note

yy After the unit is turned on by AUTO POWER
This unit automatically turns on by an input source :
function, it will be automatically turned off if
Optical, LG TV or Bluetooth.
there is no signal for a certain period of time
When you turn on your TV or an external device from the TV connected by LG Sound Sync
connected to this unit, this unit recognizes the input (Optical/Wireless).
signal and selects the suitable function. You can hear
yy After the unit is turned on by AUTO POWER
the sound from your device.
function, it will be automatically turned off if
If you try to connect your Bluetooth device, this there is no signal for a certain period of time
unit turns on and the unit will be connected to your from the external device.
Bluetooth device.
yy If you turned off the unit directly, it cannot
To turn on this function, press and hold J on the be turned on automatically by AUTO POWER
remote control for about 3 seconds and press it once function. However the unit can be turned on
again while “OFF - AUTO POWER” is scrolled. by AUTO POWER function when optical signal
To check the status of this function, press and hold comes in after 5 seconds of no signal.
J on the remote control.
3
yy Depending on the connected device, this
function may not operate.

Operating
To turn off this function, press and hold J on the
remote control for about 3 seconds and press it once yy If you disconnect Bluetooth connection by
again while “ON - AUTO POWER” is scrolled. this unit, some Bluetooth devices try to
connect to the unit continually. Therefore it is
recommended to disconnect the connection
before turning off the unit.
yy When you turn on this unit for the first time,
status of Auto Power function is turned on.
yy To use this function, the main unit must be
registered in paired devices list of Bluetooth
device.
yy You can set the Auto Power function only
when this unit is turned on.
 32 Operating

Auto function change Quick Start

This unit recognizes input signals such as Optical,
HDMI ARC, Bluetooth and LG TV and then changes This unit can stay in standby mode with low power
suitable function automatically. consumption, so that the unit can reduce boot time
when you turn on this unit.
When optical signal comes in To turn on this function, press 1 on the unit for 3
When you turn on the external device connected to seconds when the unit is turned on.
this unit by an optical cable, this unit changes the
“ON - Q. START” appears in display.
function to optical. You can hear the sound from your
device. To turn off this function, press 1 on the unit for 3
seconds again when the unit is turned on.
When you try to connect BLUETOOTH “OFF - Q. START” appears in display.
device ,,Note
When you try to connect your Bluetooth device to yy If the Quick start function is set and an AC
3 this unit, Bluetooth function is selected. Play your power is accidently re-connected to the unit
music on the Bluetooth device. by power failure etc., the Quick start function
Operating

will activate when the unit is turned on and

When you turn on your TV or an off once.
external device yy When the Quick start function is set, power
When you turn on your TV or an external device consumption will be higher than when the
connected by the optical, LG sound sync (optical or Quick start is off.
wireless) or HDMI ARC this sound bar will change yy This function may not work depending on the
to a suitable function so you can listen to the sound models.
through it.

,,Note
yy This unit does not change the function to
optical if SIMPLINK of the connected TV,
Bluray disc player, set-top box or etc. device
set to on or connected CEC supported device
is turned on.
If you want to use the auto function change,
turn off SIMPLINK function on your LG TV.
It takes for about 30 seconds to turn off
SIMPLINK.
yy If the Bluetooth connection lock function
is set, Bluetooth connection will be only
available on Bluetooth and LG TV function.
(Page 35)
 Operating 33

Using a Bluetooth Listening to Music of a

Bluetooth Device
Wireless Technology Before you start the pairing procedure, make sure
that the Bluetooth feature on your smart device
is turned on. Refer to your Bluetooth device’s user
About Bluetooth guide. Once a pairing operation is performed, it does
Bluetooth is wireless communication technology for not need to be performed again.
short range connection. 1. Select the Bluetooth function by pressing F
The sound may be interrupted when the connection repeatedly.
interfered by the other electronic wave or you Appears “BT” and then “READY” in display
connect the Bluetooth in the other rooms. window.
Connecting individual devices under Bluetooth 2. Operate the Bluetooth device and perform
wireless technology does not incur any charges. A the pairing operation. When searching for this
mobile phone with Bluetooth wireless technology speaker on your Bluetooth device, a list of the 3
can be operated via the Cascade if the connection devices found may appear in the Bluetooth
was made via Bluetooth wireless technology. device display depending on the type of

Operating
yy Available Devices : Smart phone, MP3, Notebook, Bluetooth device.
etc. Your speaker appears as “LG SL6Y(XX)”

yy Version: 4.0 3. Select the “LG SL6Y(XX)”.

yy Codec: SBC, AAC ,,Note

yy XX means the last four digits of address.
For example, if your unit has a MAC
Bluetooth profiles address such as 9C:02:98:4A:F7:08, you
In order to use Bluetooth wireless technology, will see “LG SL6Y(08)” on your Bluetooth
devices must be able to interpret certain profiles. This device.

speaker is compatible with following profile.
yy Depending on the Bluetooth device type,
A2DP (Advanced Audio Distribution Profile) some devices have a different pairing way.
For details about Bluetooth pairing, refer
to your Bluetooth device manual.
 34 Operating

4. When this unit is successfully connected with ,,Note

your Bluetooth device, yy If Bluetooth connection does not work well,
“PAIRED” [ your device’s name [ “BT” appears try pairing it again.
on the display window.
yy The sound may be interrupted when the
,,Note connection has interference by the other
yy If it is unavailable to display device name electronic waves.
on the unit, “-” will be displayed. yy Pairing is limited to one Bluetooth device per
yy To check the connected device’s name, unit and multi-pairing is not supported.
press J on the remote control. The yy Depending on the type of the device, you may
connected Bluetooth device’s name is not be able to use the Bluetooth function.
displayed.
yy You can enjoy Bluetooth function using
smart phone, MP3, Notebook, etc..
5. Listen to music.
yy The more distance between the unit and the
To play music in your Bluetooth device, refer to Bluetooth device, the lower the sound quality
3 your Bluetooth device’s user guide. becomes.
,,Note yy Bluetooth connection will be disconnected
Operating

yy When using Bluetooth technology, you have when the unit is turned off or the Bluetooth
to make a connection between the unit and device gets to far from the unit.
the Bluetooth device as close as possible and yy When Bluetooth connection is disconnected,
keep the distance. connect the Bluetooth device to the unit
However it may not work well in the case again.
below :
yy When the unit is not connected, “READY”
-- There is an obstacle between the unit and appears in the display window.
the Bluetooth device.
yy When you connect Bluetooth device (iOS
-- There is a device using same frequency device etc.) to this unit or operate the device,
with Bluetooth technology such as a the volume level can be synchronized with
medical equipment, a microwave or a each other.
wireless LAN device.
yy If you change to another function after
connecting Bluetooth, Bluetooth connection
will be disconnected. And you return to
Bluetooth function, Bluetooth connection
will be connected automatically.
 Operating 35

Controls connected Bluetooth Using BLUETOOTH App

device
You can control the connected Bluetooth device from ,,Note
the unit; play, pause, skip, volume. yy Only Android OS is available to use “Music
,,Note Flow Bluetooth” app with this unit.
yy Only Android OS and iOS is available to use yy Additional data charges may occur if installed
this function. over 3G/4G, according to your device plan.
yy This function may not be supported
depending on the Bluetooth device or some
of TV operated differently. About “Music Flow Bluetooth” App
“Music Flow Bluetooth” app brings a suite of new
features to this unit.
Bluetooth connection lock (BT To enjoy more features, you are recommended to 3
LOCK) download and install free “Music Flow Bluetooth”

Operating
app.
You can limit Bluetooth connection to only
BT (Bluetooth) and LG TV function to prevent
unintended Bluetooth connection. Install “Music Flow Bluetooth”
To turn on this function, press and hold N on App onto Your BLUETOOTH
the remote control for about 3 seconds in BT
(Bluetooth) function and press it once again while Device
“OFF - BT LOCK” is scrolled. Then you can limit There are two ways to install “Music Flow Bluetooth”
Bluetooth connection. app onto your Bluetooth device.
To turn off this function, press and hold N on
the remote control for about 3 seconds in BT Install “Music Flow Bluetooth” App
(Bluetooth) function and press it once again while through QR code
“ON - BT LOCK” is scrolled.
1. Install “Music Flow Bluetooth” app through QR
,,Note code. Use the scanning software to scan the QR
Even if you set up BT LOCK function to On, this code.
sound bar turns on by Auto Power function. Turn
off Auto Power function to prevent it. (Page
31)

2. Tap an icon for installation.

,,Note
yy Make sure that your Bluetooth device is
connected to the Internet.
yy Make sure that your Bluetooth device
has a scanning software application. If you
don’t have one, download one from “Google
Android Market (Google Play Store)”.
yy Depending on area, QR code may not work.
yy You can find the available application of this
unit by using “LG Audio” app.
Android OS: Ver 5.0 (or later)
 36 Operating

Install “Music Flow Bluetooth” App ,,Note

through “Google Android Market yy “Music Flow Bluetooth” app will be available
(Google Play Store)” in the software version as follow;
-- Android O/S : Ver 4.0.3 (or later)
1. Tap the “Google Android Market (Google Play
Store)” icon. yy If you use “Music Flow Bluetooth” app for
operation, there would be some differences
2. In the search bar, type in the “Music Flow between “Music Flow Bluetooth” app and
Bluetooth” and search it. the supplied remote control. Use the supplied
3. In the search result list, find and tap “Music Flow remote control as necessary.
Bluetooth” to start downloading Bluetooth app. yy Depending on the Bluetooth device, “Music
4. Tap an icon for installation. Flow Bluetooth” app may not work.

,,Note yy After connection of “Music Flow Bluetooth”

app, music may be output from your device. In
yy Make sure that your Bluetooth device is
connected to the Internet. this case, try connecting procedure again.
3 yy If you operate the other applications or
yy Make sure that your Bluetooth device is
change the settings on your Bluetooth device
Operating

equipped with “Google Android Market

(Google Play Store)”. while using “Music Flow Bluetooth” app,
“Music Flow Bluetooth” app may operate
abnormally.
yy When “Music Flow Bluetooth” app operates
Activate BLUETOOTH with abnormally, check your Bluetooth device and
the connection of “Music Flow Bluetooth”
“Music Flow Bluetooth” App app and then try to connect again.
“Music Flow Bluetooth” app helps to connect your yy Depending on the smart phone's operating
Bluetooth device to this unit. system, you have some differences for “Music
Flow Bluetooth” operation.
1. Tap “Music Flow Bluetooth” app icon on the
home screen to open “Music Flow Bluetooth” yy Even though Bluetooth connection will
app, and go to the main menu. be disconnected, you can use “Music Flow
Bluetooth” app when you change the
2. If you want to get more information to operate,
function.
tap [Setting] and tap [Help] menu.
yy Additional features offered by "Music Flow
Bluetooth" app may not work depending on
the distance between this unit and Bluetooth
device and wireless conditions.
 Troubleshooting 37

Troubleshooting

General
Symptoms Cause & Solution
yy Turn off the power of this unit and the connected external device (TV, Woofer,
DVD-player, Amplifier, etc.) and turn them on again.
The unit does not work yy Disconnect the power cord of this unit and the connected external device (TV,
properly. Woofer, DVD-player, Amplifier, etc.) and then try connecting again.
yy Previous setting may not be saved when device power is shut off.

yy The power cord is unplugged.

Plug in the power cord.
No Power
yy Check whether electricity failed.
Check the condition by operating other electronic devices.

yy Incorrect input source is selected.

Check the input source and select the correct input source. 4
yy The mute function is activated.

Troubleshooting
No sound Press [ (Mute) or adjust the volume level to cancel the mute function.
yy When you are using connection with a external device (set top box, Bluetooth
device etc.), adjust volume level of the device.

yy The power cord of the subwoofer is not connected.

Plug the power cord into the wall outlet securely.
No woofer sound
yy Pairing between the unit and the subwoofer gets disconnected.
Connect the unit and the subwoofer. (Page 16)

yy The remote control is too far from the unit.

Operate the remote control within about 7 m.
The remote control does yy There is an obstacle in the path of the remote control and the unit.
not work properly. Remove the obstacle.
yy The batteries in the remote control is exhausted.
Replace the batteries with new one.

yy Check connection of the external device such as TV, DVD/Blu-Ray player or

Bluetooth device.
The AUTO POWER function
does not work. yy Check the state of SIMPLINK on your LG TV and turn off SIMPLINK.
yy Depending on the connected device, this function may not operate.

yy Check whether your LG TV supports LG Sound Sync.

LG Sound Sync does not yy Check connection of LG Sound Sync (Optical or wireless).
work.
yy Check sound setting of your TV and this unit.
 38 Troubleshooting

Symptoms Cause & Solution

The unit does not connect yy Turn off the Bluetooth connection lock function. (Page 35)
with Bluetooth device

Check the details below and adjust the unit according to them.
yy With the sound bar connected with TV, change the AUDIO DIGITAL OUT
setting on TV Setup Menu from [PCM] to [AUTO] or [BITSTREAM].
When you feel the output yy With the sound bar connected with Player, change the AUDIO DIGITAL OUT
sound of the unit is low. setting on Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or
[BITSTREAM].
yy Change Audio DRC setting on connected device setup menu to [OFF] state.
yy Make sure Night time mode is not On. Turn [OFF] Night time mode.

NOTES to use wireless

Symptoms Cause & Solution
4
yy Wireless may not operate normally in weak signal area.
This device may have
Troubleshooting

yy Please install the device close enough to wireless subwoofer.

wireless interference.
yy Do not install the device on metal furniture for optimum performance.
yy When any part of your body contact the transceiver of the Bluetooth device
or sound bar.
yy When there is an obstacle or wall or the device is installed in a secluded spot.
Bluetooth device may yy When there is a device (a wireless LAN, a medical equipment or a microwave)
malfunction or make using same frequency, make the distance between the products as far away
noise in the following as possible each other.
cases. yy When connecting the device to the Bluetooth device, make the distance
between the products as close as possible each other.
yy When the device gets too far from the Bluetooth device, the connection is
disconnected and also malfunction may occur.
 Troubleshooting 39

NOTES to release Demo mode

Symptoms Cause & Solution
Can not change input source with F such as BT Unplug the power cord and plug it in again. If that
(Bluetooth), HDMI etc. and only [DEMO] indication doesn’t work, press and hold F (About 5 seconds) on
is showing in the front display. the main unit until the display indicates current selected
Remote Control does not work. (No response) function.

Troubleshooting
 40 Appendix

Trademarks and licenses

All other trademarks are trademarks of their
respective owners. The Bluetooth® word mark and logos are
registered trademarks owned by the Bluetooth
SIG, Inc. and any use of such marks by LG
Electronics is under license.
Other trademarks and trade names are those of
their respective owners.
Manufactured under license from Dolby
Laboratories. Dolby, Dolby Audio, and the double-D
symbol are trademarks of Dolby Laboratories.

The terms HDMI and HDMI High-Definition

Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI
Licensing LLC in the United States and other
countries.

For DTS patents, see http://patents.dts.com.

Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol
together, and Digital Surround are registered
5 trademarks and/or trademarks of DTS, Inc. in the
United States and/or other countries. © DTS, Inc.
Appendix

All Rights Reserved.

For DTS patents, see http://patents.dts.com.

Manufactured under license from DTS Licensing
Limited. DTS, the Symbol, DTS and the Symbol
together, Virtual:X, and the DTS Virtual:X logo are
registered trademarks or trademarks of DTS, Inc. in
the United States and/or other countries. © DTS,
Inc. All Rights Reserved.
 Appendix 41

Specifications
General
Power consumption Refer to the main label on the unit.
yy Model : DA-50F25
yy Manufacturer : Asian Power Devices Inc.
AC adapter
yy Input : 100 - 240 V ~ 50 - 60 Hz
yy Output : 25 V 0 2 A
Dimensions (W x H x D) Approx. 1060.0 mm X 57.0 mm X 85.0 mm With foot
Operating temperature 5 °C to 35 °C (41 °F to 95 °F)
Operating humidity 5 % to 90 %
Bus Power Supply (USB) 5 V 0 500 mA
Available Digital Input Audio
32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
Sampling Frequency
Available Digital Input Audio format Dolby Audio, DTS Digital Surround, PCM

Input/Output
OPTICAL IN 3 V (p-p), Optical jack x 1
HDMI IN 19 Pin (Type A, HDMI™ connector) x 1
5
HDMI OUT 19 Pin (Type A, HDMI™ connector) x 1

Appendix
Amplifier (RMS Output)
Total 420 W RMS
Front 80 W RMS x 2 (4 Ω at 1 kHz, THD 10 %)
Center 40 W RMS (4 Ω at 1 kHz, THD 10 %)
Subwoofer 220 W RMS (3 Ω at 80 Hz, THD 10 %)
 42 Appendix

Wireless subwoofer
Power requirements Refer to the main label on the subwoofer.
Power consumption Refer to the main label on the subwoofer.
Type 1 Way 1 Speaker
Impedance 3Ω
Rated Input Power 220 W RMS
Max. Input Power 440 W RMS
Dimensions (W x H x D) Approx. 171.0 mm x 393.0 mm x 248.5 mm

SPK8-S (SPK8-S, S78S1-S), Sold Separately

Wireless receiver
Power requirements Refer to the main label on the wireless receiver.
Power consumption Refer to the main label on the wireless receiver.
Rear 70 W RMS x 2 (3 Ω at 1 kHz, THD 10 %)
Dimensions (W x H x D) Approx. 60.0 mm x 220.0 mm x 175.0 mm

Rear speakers (Each)

Type 1 Way 1 Speaker
5 Impedance 3Ω
Rated Input Power 70 W RMS
Appendix

Max. Input Power 140 W RMS

Dimensions (W x H x D) Approx. 100.0 mm x 140.0 mm x 100.0 mm

yy Designs and specifications are subject to change without prior notice.

 Appendix 43

Handling the Speaker

When shipping the speaker
Please save the original shipping carton and packing
materials. If you need to ship the speaker, for
maximum protection, re-pack the speaker as it was
originally packed at the factory.

Keeping the exterior surfaces clean

yy Do not use volatile liquids such as insecticide spray
near the speaker.
yy Wiping with strong pressure may damage the
surface.
yy Do not leave rubber or plastic products in contact
with the speaker for a long period of time.

Cleaning the speaker

To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not use
strong solvents such as alcohol, benzine, or thinner,
as these might damage the surface of the speaker.

Appendix