ECD-V Series

Electronically Controlled Distributor

Type Fuel Injection System
 FOREWORD
To meet the pressing needs for the diesel engine to deliver cleaner exhaust gas emissions, lower
fuel consumption, and reduced noise, advances are being made in adopting electronic control in
its fuel injection system.

This manual covers the electronic control models ECD-V3, ECD-V3 (ROM), ECD-V4, and ECD-
V5 of the electronically controlled, distributor type fuel injection system, including actual examples.
Complex theories or special functions are omitted in this manual in order to focus on the desc rip-
tion of the basic construction and operation. It hasbeen compiled to serve as a reference material
for everyone who wishes todeepen their knowledge of the electronically controlled, distributor type
fuel injection system, whose application is increasing year after year.

TABLE OF CONTENTS

Introduction (Diesel Engine and Fuel Injection System) .............................. 1

Chapter 1 (ECD-V3) .................................................................................... 15

Chapter 2 (ECD-V5) .................................................................................... 63

Chapter 3 (ECD-V4) .................................................................................... 87

© 2000 DENSO CORPORATION

All Rights Reserved. This book, parts thereof,
may not be reproduced or copied, in any form
without the written permission of the publisher.
 Introduction
Diesel Engine
and
Fuel Injection System

-1-
 Introduction - Table of Contents
1. Diesel Engine .............................................................................................. 3
1-1. Comparison to Gasoline Engine .................................................................................... 3
1-2. Diesel Engine Operation ............................................................................................... 4
1-3. Diesel Engine’s Combustion Process............................................................................ 5
1-4. Diesel Knock ................................................................................................................. 6
1-5. Combustion Chamber ................................................................................................... 6
1-6. Fuel ............................................................................................................................... 7
1-7. Exhaust Smoke ............................................................................................................. 9
1-8. Diesel Engine Performance .......................................................................................... 10
2. Fuel Injection System ............................................................................... 1 2
2-1. Fuel Injection System Composition ............................................................................... 12
2-2. Electronically Controlled Fuel Injection System .............................................................. 13

-2-
1. Diesel Engine
1-1. Comparison to Gasoline Engine
In a gasoline engine, the intake air volume is regulated by the throttle valve, which is located at the
intake and linked to the accelerator pedal. Then, the volume of fuel that corresponds to the air volume
is injected by the injectors. The air-fuel mixture is then drawn into the cylinders and become com-
pressed. In the cylinders, the air-fuel mixture is ignited by the electric sparks to caus
e combustion.
In contrast, in a diesel engine, only air is drawn during the intake stroke into the cylinder, where it
reaches a high temperature and becomes compresse d to a high pressure. Then, the injection nozzles
inject diesel fuel, which undergoes combustion andexplosion through self-ignition. Because there is
no throttle valve, the intake airvolume remains practically constant regardless of the engine speedor
load. For this reason, the engineoutput is controlled by regulating the fuelinjection volume.
Therefore, a diesel engine requires a fuel system that is different from a gasoline engine.
Air Flow Meter Air Cleaner Air Cleaner

Injector

Spark Plug Injection Nozzle

Throttle Valve

Injection Pump

GasolineEngine(EFI) DieselEngine
PQ0352 PQ0353

Reference: The table below compares the diesel engine to the gasoline en
gine.
Diesel Engine Gasoline Engine
Combustion Cycle Sabathee Cycle Auto Cycle
Compression Ratio 15~22 5~10
Thermal Efficiency % 30~40 25~30
Fuel Consumption Rate g/psh 140~210 200~280
Creation of Atomized, injected, and Gasified and mixed before
Air-Fuel Mixture mixed after compression compression
Fuel Diesel Fuel Gasoline
Fuel Consumption Volume % 30~40 100
Fuel Cost % 50~60 100

-3-
1-2. Diesel Engine Operation
An engine that completes one cycle with four strokes of the piston, or two revolutions of the crankshaft
is called a four-cycle diesel engine. An engine that completes one cycle with two strokes of the pis-
ton, or one revolution of the crankshaft, is called a two-cycle diesel engine.
The operation of a four-cycle diesel engine will be described in this manual.

Intake Valve

Intake
Intake Valve

Exhaust Compression
Nozzle

Combustion

PU0029

(1) Intake Stroke

Clean air is drawn into the cylinderas the piston descends from its top-dead-center. At this time, the
intake valve opens slightly before the piston reaches its top-dead-center in order to facilitate the
intake
has of air.ascending
started It remains again.
open for a while evenafter the piston has passed its bottom-dead-center and
(2) Compression Stroke
After the piston moves past its bottom-dead-center and starts to ascend, the intake valve closes,
causing the air that was drawn into thecylinder to become compressed with the ascent of the piston.
Because a diesel engine creates combustion by igniting the injected fuel with the heat of the com-
pressed air, the compressive pressure is much higher than in a gasoline engine. Even when the
engine speed is low, such as during starting, there is a compressive pressure of approximately 20
to
30 kg/cm2, and the compressive temperature reaches 400 to 550°C.
(3) Combustion Stroke
Near the end of the compression stroke, fuel is injected in a spray form by a nozzle that is provided in
the cylinder head. The compressive heat causes the mixture to self-ignite, resulting in a sudden
combustion and the expansion of the combustion gas pushes the piston down.
(4) Exhaust Stroke
Slightly before the piston reaches its bottom-dead-center in the combustion stroke, the exhaust
valve
opens, and the resulting
piston ascends from the difference in pressures
bottom-dead-center, thestarts the discharge
exhaust of the
gas is pushed outexhaust gas. Then, as the
of the cylinder.
As described thus far, the engine effects the four strokes of intake, compression, combustion, and
exhaust while the piston moves in the cylinder from its top-dead-center to bottom-dead-center, or
vice-versa.

-4-
1-3. Diesel Engine's Combustion Process
Here is a brief description of the combustion process of a four-cycle diesel engine.
The air that is compressed in the cylinder reaches ahigh temperature and pressure. When the nozzle
injects fuel in a spray form into this air, the fuel particles become superheated, their surface tempera-
ture rises, and they begin to evaporate. When the evaporated fuel mixes with air at an appropriate
temperature, the mixture ignites and causes combustion. This process is described in further detail
in Figure PQ0354, in terms of the relationship between the rotational angle of the crankshaft and the
pressure in the cylinder. Thus, the combustion process can be divided into the four periods shown on
the next page.

n
oi
tc Ex
je pa
in n ns
l o
e ti
u c io
f ej n
f ni
o f
tr o
e d
r ta n
E
u
s
S
s
e
r
P

(kg/cm2) o n Combustion
re ssi Injection
mp
Co Ignition lag

Top-dead-center
Crankshaft rotational angle (° )

PQ0354

(1) Ignition
In Figure lag period
PQ0354, (between
the period AA
between and
andB)
B is the preparatory period during which the fuel particles that are injected
into the cylinder absorb heat from the compressed air, thus creating an ignitable air-fuel mixture. Time-wise, this is an
extremely short period during which no rapid rise in temperature or pressure is exhibited.
(2) Flame propagation period (between B and C)
During the period between B and C given in Figure PQ0354, the air-fuel mixture that was prepared for
combustion in the previous ignition lag ignites in one or more areas at point B. As the combustion spreads
quickly in the cylinder, practically all of the mixture burns simultaneously, causing the pressure to rise
rapidly to point C. The pressure rise at this time is influenced by the volume of fuel that was injected during
the ignition lag time as well as by its atomized state.
(3) Direct combustion period (between C and D)
During the period between C and D given in Figure PQ0354, fuel continues to be injected past point C, and
burns immediately upon injection without causing any ignition lag, due to the flame that was created between
points B and C. Therefore, the changes in the pressure that occur during
this period can be adjusted to acertain
extent by appropriately regulating the fuel injection volume.
(4) Afterburn period (between D and E)
The injection
will burn of fuel
during the is completed
expansion point
at D
period given inFigure
between points PQ0354. Any
D and E, fuel is
which that did not
called theburn
completely
“afterburn up to this
period”. point the
Because
exhaust temperature increases and the thermal efficiency decreases as this period becomes longer, it is necessary to
keep it short.
Although the combustion process can be divided into the four periods as described, in contrast to the direct combustion
period, the ignition lag period and
the flame propagation period can be considered preparatory
a period. The outcome of
this period greatly influences combustion. Therefore,proper
the injection starting pressurethe
of nozzle, state of atomi-
zation, compressive pressure, and injection timing become important factors.
-5-
1-4. Diesel Knock
The knocks that occur in a diesel engine and a gasoline engine are similar in that they are associ-
ated with an abnormal rise in pressure during combustion. However, the knocks of the two engines
differ fundamentally in the timing in which theyoccur, their causes, and situations. A diesel knock is
created by the rapid rise in pressure asa result of the instantaneous explosion and combustio n of the
flammable air-fuel mixture that was created during the ignition lag period. Meanwhile, a gasoline
engine knock occurs because the unburned air-fuelmixture is susceptible to self-ignition. As the air-
fuel mixture burns instantly at the end of the flame propagation, it results in alocalized pressure rise
and a considerable pressure imbalance in the cylinder. This generates large pressure waves that
create knocking sounds.
The diesel engine knock is created as a result of thedifficulty in causing self-ignition, while the gaso-
line engine knock is created because of the ease with which self-ignition occurs. Thus, their causes
are directly opposite to each other.
In a gasoline engine, a knock is oneof the symptoms of abnormal combustion. However, in a diesel
engine, it is difficult to clearly separate anormal combustion from one that isaccompanied by knocks.
Therefore, knocks are distinguished merely by whether they are crea ted by a rapid pressure rise or
if they apply shocks to the various areas of the engine.
To prevent a diesel knock, it is important to shorten the ignition lag period, when we consider its
cause. Generally speaking, nozzles are designed to minimize the volume of fuel that is injected dur-
ing this period. Other preventive measures are the following:
a. Using diesel fuel with a high cetane value.
b. Increasing the temperature in the cylinder (to increase the compressive pressure).
c. Optimizing the coolant temperature.
d. Optimizing the injection timing.
e. Optimizing the fuel injection pressure and atomization.
1-5. Combustion Chamber
(1) Direct Injection Type
The direct injection type uses a nozzle to directly in-
ject fuel into the combustion chamber, which is formed
in the area between the cylinder and the piston head,
where combustion takes place.
The direct injection system has been ado pted in many Ignition Nozzle
engines in recent years due to its low fuel consump-
tion rate and high economy. Combustion
Chamber
Piston PU0030

(2) Pre-combustion Chamber Type

The pre-combustion chamber type contains a sub-
chamber that is called a “pre-combustion
chamber”above the main combustion chamber. Fuel Nozzle

from thechamber
bustion injectionin
nozzle
orderistoinjected into theof
burn a portion pre-com-
the fuel, Glow Plug
and the resulting pressure is used to push the remain- Pre-combustion
ing unburned fuel into the main combu stion chamber. Chamber
The swirl that is created in the cylinder thoroughly
mixes the fuel with air, resulting in a complete com- Main
Pstion
bustion. Combustion
Chamber Vent Hole PU0031

-6-
(3) Swirl Chamber Type
The swirl chamber type contains aspherical sub-cham- Glow Plug
ber called a “swirl chamber” in the cylinder head or in
the cylinder. The air that is compressed by the piston
flows into the swirl chamber and continues to form a
swirl. The injection nozzle then sprays fuel into this Injection Nozzle
swirl, which results in most of the fuel being burned in Swirl Chamber
the swirl chamber. Some of the unburned fuel that re- Vent Hole
mains is then pushed out to the main combustion
Main Combustion
chamber where it undergoes acomplete combustion. Chamber
Piston PU0032

(4) Air Chamber Type

The air chamber type contains a sub-chamber caled an “air chamber” in the piston or in the cylinder
head. The injection nozzle sprays the fuel to the mouth of the air chamber, and it is then ignited and
burned in the main combustion chamber. At this time, a portion of the fuel enters the air chamber
where it is burned, thus raising the pressure in the air chamber. When the piston starts to descend,
the air in the air chamber is pushed out to the main combustion chamber in order to help complete
the combustion in the chamber.
The air chamber type is not currently used in Japan.
Reference: The table below compares the types of combustion chamber
s.
Pre-Combustion
Direct Injection Type Swirl Chamber Type Air Chamber Type
Chamber Type
Construction Simple Complex Somewhat complex Complex
Compression Ratio 12~20 16~22 Medium Medium

Fuel Good quality Poor quality Medium Medium

Preheating device
Starting Easy ← Somewhat easy
required
kg/cm2
Net Average Effective Pressure 5.6~8.0 5.2~8.0 5.5~7.5 5.5~7.5
Maximum Engine Speed rpm 3,000 4,000 4,500 3,000
Maximum Cylinder Pressurekg/cm2 60~100 45~80 50~80 45~70
Net Fuel Consumption Rateg/psh 160~200 180~250 180~230 180~230
Injection Nozzle Type Hole type Pin type ← ←
Injection Pressure kg/cm2 150~300 80~150 80~150 80~150
Minimum Excess Air Ratio* 1.5~1.7 1.2~1.7 1.3~1.6 1.3~1.6
Actual supplied air volume
*Excess air ratio Theoretical
= air volume required for combustion

1-6. Fuel
The automotive diesel engines use the lighter diesel fuel, and the low-speed diesel engines for ships
use the heavier marine diesel fuel. The lighter diesel fuel, like gasoline, kerosene, and heavier diesel
fuel, is produced during the petroleum refining process. It has a boiling point of between 200 and
330°C, a specific gravity of 0.82 to 0.86, and a heating value of 10,000 to 11,000 kca/kg. Very similar
to kerosene, diesel fuel is slightly more yellowish and viscous.
-7-
(1) Ignitability of Diesel Fuel
The ignitability of fuel is determined by the self-ignition
that results from raising the temperatureof the fuel, with-
out the presence of a flame nearby.In the example shown
in Figure PQ0357, a few drops of diesel fuel and gaso- Diesel Fuel Gasoline
line are squirted on top of a heated iron plate. After a
while, the diesel fuel bursts into flames, but gasoline
evaporates immediately without burning. This means that
diesel fuel has better ignitability, and the temperature at
which it ignites is called the “ignition point”. Thus, the Heated iron
lower the ignition point of fuel, the better its ignitability. plate
PQ0357
In a diesel engine, in which fuel is burned by the com-
pressive heat of the air, ignitability is an important char-
acteristic. It greatly influences the length of time after the
fuel is injected into the combustion chamberuntil it starts
to burn, which is called the “ignition lag time”.
The measurement that is used to indicate the ignitability of diesel fuel is the cetane value. A fuel with a low
cetane value has poor ignitability and a longer ignition lag time, which leads to diesel knocks.
(2) Viscosity of Diesel Fuel
Viscosity is one of the important characteristics of the fuel that is used in diesel engines. A high viscosity
results in large fuel particles when the fuel is injected in the combustion chamber, which leads to sluggish
dissipation and poor combustion. Conversely, a low viscosity results in poor lubrication of the various parts
of the fuel system such as the injection pump and nozzles, leading to premature wear or seizure.
(3) Sulfur Content of Diesel Fuel
The sulfur that is included in the fuel turns into sulfurous acid gas and sulfuric anhydride during combustion.
They combine with the water that results from the combustion to form sulfuric acid, which is highly corro-
sive. Because sulfur compounds also have poor ignitability and combustibility, they tend to create black
smoke and contribute to fouling the engine oil.

(4) Volatility of Diesel Fuel

Because diesel fuel has a high boiling point, it is practically non-volatile at room temperature. However,
volatility is desirable to a certain extent, considering that diesel fuel must become gasified and mixed with
air, and combustion can only occur when its density enters the combustion range.
(5) Specifications for Diesel Fuel
The properties of the diesel fuel that is used in diesel engines are specified by JIS K2204 as given in the
table below.
Diesel Fuel Type *
No. 1 No. 2 No. 3 Special No.
Reaction Neutral Neutral Neutral Neutral
Flash point °C 50 minimum 50 minimum 50 minimum 50 minimum
Fractional distillation property 90%; dis- °C
350 maximum 350 maximum 350 maximum 350 maximum
tillation temperature
Pour point °C −5 maximum −10 maximum −20 maximum −30 maximum

Carbon residue of 10% bottom oil 0.15 maximum 0.15 maximum 0.15 maximum 0.15 maximum
Cetane value 50 minimum 45 minimum 40 minimum 42 minimum
Dynamic viscosity (30°C) CST 2.7 minimum 2.5 minimum 2.0 minimum 1.8 minimum
Sulfur content % 1.20 maximum 1.20 maximum 1.10 maximum 1.00 maximum
* Applications by type
No. 1: general use, No. 2: general use, No. 3: cold-weather use, Special No. 3: extreme cold-weather use Ordinarily,
No. 2 diesel fuel is widely used.
-8-
1-7. Exhaust Smoke
(1) White Smoke
Resulting from the discharge of the minute particles of fuel or engine oil that have not been burned,
this type of smoke is likely to occur when the engine is started in a cold climate.
(2) Blue Smoke
Resulting from the non-combustion, partial combustion, or thermal decomposition of the fuel or en-
gine oil, this type of smoke is the discharge of minute particles in a liquefied state.
While both white and blue smokes are minute particles in a liquefied state, the particle diameter of
the white smoke is 1µ or more, and the bluesmoke is 0.4µ or less. The difference in size is consid-
ered to create different colors.

(3) Black Smoke Sub-Chamber Type

a. Generally speaking, smoke refers to black smoke. ) Direct Injection Type
ch
When fuel becomes baked due to the lack of air, it s
o
thermally decomposes and the carbon residues are (B
e
discharged in the form of black smoke. k
o
Figure PU0033 describes the relationship between m
S
the injection volume and black smoke. In a sub-
chamber type engine, the smoke is denser than in
the direct injection type when the injection volume
is small. However, as the injection volume in- Air-Fuel Ratio ×10-2
PU0033
creases, the smoke of the sub-chamber type hasa
lower tendency to worsen, and suddenly becomes
denser in the vicinity of the full load.
Sub-Chamber Type
) Direct Injection Type
ch
s
o
b. When the injection timing is advanced, the ignition (B
e
lag becomes greater in a direct-injection type as k
o
shown in Figure PU0034. Because the volume of m
S
fuel that becomes gasified increases before igni-
tion, the amount of black smoke decreases.
In a sub-chamber type, the ignition lag also be-
comes greater. However, because the ratio of com- Injection Timing (BTDC) PU0034
bustion in the sub-chamber that contains a small
volume of air is greater, the amount of black smoke
increases.

c. Generally speaking, the optimal injection timing forfavorable black smoke conditions islater than
the optimal injection timing for favorable fuel conditions.

-9-
1-8. Diesel Engine Performance
(1) Engine Performance Curve
An engine performance curve or characteristic curve
shows the performance of an engine at a glance. As
Figure PU 0035 shows, the performance curve indi- e )
u
) rq m⋅
cates the maximum output horsepower, shaft torque, S o g
P(
T
tf (k
and fuel consumption rate at each engine speed. t a
u h
The engine generates greater torque as the gas pres- tp S
u
sure in the cylinder increases. However, when theen- O
gine speed exceeds a certain speed, thecombustion
conditions change due to the reduction in the intake
air volume, thus causing the engine torque to decrease
at high speeds. At intermediate speeds, theair intake
is more favorable, which leads to a better combustion n
condition and greater torque. At lower speeds, thein- io
t
p
take air volume decreases due to the opening and m
u
)
h
closing timing of the intake valve, causing the torque s s
n
o p
/
to decrease. C g
(
l e
e t
u a
Although the power output increases in proportion to F R
the engine speed, it does not increase significantly in
the high-speed range due to the reduction in torque.
The fuel consumption rate is directly influen
ced by the Engine Speed (rpm)
PU0035
combustion conditions, and this rate is the lowest at
an engine speed in the vicinity of the maximum torque,
in which the combustion condition is the best.

(2) Factors Contributing to Performance

a. Injection Timing
The engine output varies in accordance with the injection timing. Because the injection timing at
the maximum output varies by engine speed, it is better to advancethe injection timing along with
the increase in the engine speed.
Care must be taken to change the injection timing because it is closely related to diesel knocks.

b. Injection Volume
)
If the injection volume is changed while the engine S
(P
t
speed and the injection timing remain constant, the u
tp tput
ft Ou
u s
power output and the fuel consumption rate will be O
tf Sha
s
le
r y
ra
k
c
a
l
a lo
as shown in Figure PU0036. The power output in- h
S
o
c a
y
r k
G
B
k
r
a
t G c D
creases in proportion tothe injection volume within s
o
m
t
h
a
B
l
l ig
the range where black smoke is notemitted. How- te
a
R
A L

ever, if the injection volume is increased to the ex- n

p
o
ti
m
)
h
s Fuel Consumption Rate
u /p
s (g
n
o
tent that black
decreases andsmoke is emitted, the power output
is uneconomical. l
u
F
C
e

Injection Volume (l/h) PU0036

- 10 -
c. Nozzle and Nozzle Valve Opening Pressure
When the type of throttle nozzle is changed, even though its spray angle remains the same, the
atomization performance and injection volume characteristics change. Therefore, the maximum
output, noise, or idle stability will be affected.
When the nozzle opening pressure decreases, the injection volume increases, causingthe output
to increase slightly. However, the emission of black smoke alsoincreases.

d. Maximum Engine Speed

The increase in engine speedcauses the power output to also increase. However, the inertia of the
moving parts also increases, causing a reduction in the durability of the engine. Furthermore, the
friction between the piston or the piston rings and the cylinder surface increases, and this factor
also limits the maximum speed of the engine.

ity
e. Altitude s
n
At high altitudes, the air density decreases and the e
D
ri
emission of black smoke increases. In order to A
maintain the black smoke emissions within the
specified value, it is necessary to decrease the in-
jection volume in accordance with the air density.
This results in a power output reduction of 10 per-
cent per 1,000 meters of altitude.
Some automobiles that are operated in an area Altitude (m)
with significant altitude differences may be PU0037
equipped with an altitude compensator system
(ACS) that automatically decreases the injection
volume.

- 11 -
2. Fuel Injection System
2-1. Fuel Injection System Composition
In a diesel engine, fuel must be injected into the air that is highly compressed in the combustion
chamber. This requires a pump to pressurize the fuel to ahigh pressure. The actual system consists
of the following components:
a. Fuel injection pump : Pressurizes fuel to a high pressure and pumps it to the injection nozzle.
b. Injection nozzle : Injects fuel into the cylinder.
c. Feed pump : Located inside the fuel injection pump, it draws fuel from the fuel tank.
d. Fuel filter : Filters the fuel. Also, there are some that contain a fuel sedimenter at the
bottom of the filter to separate the moisture inthe fuel.
e. High pressure pipe : Delivers fuel to the injection nozzle. Steel pipe is used to sustain high
pressure.

A portion of the fuel that isdelivered to the nozzle lubricates the sliding part ofthe nozzle and returns
to the fuel tank via the overflow pipe.

Injection Nozzle High Pressure Pipe

Fuel Filter
High Pressure Fuel

Engine

Injection Pump

Return Pipe

Fuel Tank
PU0038

- 12 -
2-2. Electronically Controlled Fuel Injection System
An electronically controlled fuel injection system uses acomputer to control the injection volume and
the injection timing. The following ECD (Electronically Controlled Diesel) fuel injection systems are
based on the mechanical distributor type VE pump: the ECD-V3, ECD-V4, and ECD-V5.
(1) Transition of fuel injection systems and ECD-V series
(unit: million units)
2
d
e
c
u
d
ro
p
s it
n
u1 ECD
f
e ro
b
m
u
n l Mechanical Type
ta
o
T0

≈
1955 1975 1980 1985 1990 1995

*Pump production started [1957]

*VE Pump [1977]
*Inline Type (NB type) Pump [1981]
*Inline Type (NL type) Pump [1987]
Transition of ECD-V Series
ECD-V1 [1982]
↓
ECD-V1(improved type) [1983]

→ECD-V3 [1985] → ECD-V3 (ROM) [1997]

Base
→ECD-V5 [1998]

New mechanism and new model

→ECD-V4 [1998]

(2) Characteristics of ECD-V Series

Cylinder
Model displacement Rated pump speed Vehicle Engine 150
(liters) (rpm)
ECD-V4
•Passenger vehicles Swirl re 130
ECD-V3 u
s
(ROM) 3.0 maximum 4500 maximum s
•Leisure vehicles chamber e
r
P
n 110
•Passenger vehicles ito
Direct c ECD-V5
ECD-V4 4.0~5.0 3500 maximum •Leisure vehicles e j
n I 90
injection
•Small trucks (MPa)

ECD-V5 2.0 maximum 4500 maximum •Passenger vehicles Direct 70

•Leisure vehicles injection ECD-V3 (ROM)
50
≈

50 100
Maximum Injection Volume (mm3/st)

- 13 -
- 14 -
Chapter 1
ECD-V3

- 15 -
 Chapter 1 - Table of Contents
1. Outline ........................................................................................................ 17
2. System Composition ............................................................................... 17
2-1. Construction of Injection Pump ..................................................................................... 18
2-2. System Components (on-vehicle layout example) ........................................................ 19
3. Fuel Pr essure-Feed and Injection ......................................................... 19
4. Fuel Injection Volume Control ................................................................ 20
4-1. Outline of Injection Volume Control ............................................................................... 20
4-2. System Components .................................................................................................. 21
4-3. Fuel Injection Volume Control ....................................................................................... 26
4-4. Relationship Between Vehicle (Engine) and Fuel Injection Volume Control ................... 30
4-5. Determining the Final Injection Volume ........................................................................ 31
4-6. Various Types of Injection Volume Corrections ............................................................ 31
4-7. Summary of Injection Volume Control (typical examples) .............................................. 34
5. Fuel Injection Timing Control ................................................................. 36
5-1. Outline of Injection Timing Control ................................................................................ 36
5-2. Components ................................................................................................................ 36
5-3. Injection Timing Control................................................................................................ 37
5-4. Determining the Final Injection Timing.......................................................................... 40
5-5. Various Times of Timing Advance Corrections ............................................................ 40
5-6. Timing Control Valve (TCV) Actuation Method ............................................................. 42
5-7. Summary of Injection Timing Control (typical examples)................................................ 43
6. Idle Speed Control ................................................................................... 45
6-1. Outline ......................................................................................................................... 45
6-2. Idle Speed Control ....................................................................................................... 45
7. Idle Speed Control ................................................................................... 46
7-1. Function....................................................................................................................... 46
7-2. Construction ................................................................................................................ 46
7-3. Operation .................................................................................................................... 47
8. EGR Control .............................................................................................. 53
8-1. Construction and Operation of Components................................................................. 53
8-2. Determining the EGR Volume ...................................................................................... 54
8-3. EGR Correction Coefficient ......................................................................................... 54
9. Glow Plug Contro l .................................................................................... 55
9-1. Glow Plug Indicator Illumination Time control ................................................................ 55
9-2. Glow Plug Relay Control .............................................................................................. 55
10. Other Controls (control types by engine model) ............................... 56
11. Diagnosis Function ............................................................................... 57
12. Fail-Sa fe Functi on .................................................................................. 57

- 16 -
1. Outline
In the electronically controlled fuel injection system of a distributor type pump, the computer detects
the operating conditions of the engine in accordance with the signals received from various sensors
(engine speed, acceleration, intake air pressure, water temperature sensors, etc.) in order to effect
the following basic controls:
a. Fuel injection volume control
b. Fuel injection timing control
c. Idle speed control
d. Throttle control
e. EGR control
f. Glow plug control
In addition, the system provides the following auxiliary functions:
g. Diagnosis function
h. Fail-safe function
2. System Composition
The electronically controlled system of a distributor type pump can be broadly divided into the following
three components: sensors, microcomputer (ECU), and actuators.

<Sensors> <Computer> <Actuators>

Solenoid Spill Valve
Speed Sensor
ECU
Acceleration Sensor Fuel Temperature Sensor

Crankshaft Position Sensor

Speed Sensor
Water Temperature Sensor

Intake Air Temperature Sensor

Fuel Temperature Sensor

Intake Air Pressure Sensor

Other signals used:vehicle speed signal

•air conditioner signal
•startersignal Timing Control Valve
PR0063

Sensors Detect the conditions of the engine or the pump itself.

Regulate the injection volume and injection timing in accordance with the signals
Actuators received from the computer.
Calculates the injection volume and injection timing that are optimal for the en-
Computer
gine operation in accordance with the signals from the sensors.

- 17 -
2-1. Construction of Injection Pump
The following electrical parts are attached to the elec-
tronically controlled distributor type pump:
a. Actuators
•Solenoid spill valve (SPV) to control the injection
volume
•Timing control valve (TCV) to control the injection tim-
ing Correction
b. Sensors Resistors
•Speed sensor
•Fuel temperature sensor
c. ROM (or correction resistors on the conven- Conventional (correction resistor) Type QN0003

tional type) Fuel Temperature NE (engine speed) Sensor

Sensor

Solenoid
Spill Valve

ROM
or Correction
Resistor Timing Control Valve

ROM Type
CS0921

Fuel Temperature Sensor NE (engine speed) Sensor

Solenoid Spill Valve
NE (engine speed) Sensor

Pulsar
Timing Control Valve
PR0062

- 18 -
2-2. System Components (on-vehicle layout example)
Turbo Pressure
EVRV Sensor
Engine Control
Computer
AccelerationSensor
Injection Pump VSV No.2 DLC3 Diagnosis
EVRV Connector

EGR Valve

Venturi Sensor
Intake Air Temperature Sensor

Crankshaft Position
Sensor

Water Temperature Sensor

VSV No.1
System Component Layout A20062

3. Fuel Pressure-Feed and Injection

The mechanisms for pressure-feeding and distributing fuel are basically the same as in the conven-
tional mechanical pump, although there are some differences associated with the adoption of the
solenoid spill valve.
The solenoid spill valve is provided in thepassage that connects the pump chamber with the pressure
chamber of the plunger, and it remains closed when the coil is energized. (See page 28 for details on
the solenoid spill valve.)
(1) Suction
Fuel is drawn into the pressure chamber when the Solenoid Spill
plunger descends. Valve (closed)
Pump Chamber
•Suctionport: open Suction Port
•Distribution port: closed
•Solenoid spill valve: closed (energized)
Pressure
Chamber
Roller
Plunger
Cam Plate Nozzle
Distribution Port
Suction Stroke PR0064

(2) Injection
The plunger ascends while rotating in orderto pump Solenoid Spill
fuel. Valve (closed)
•Suctionport: closed
•Distribution port: open
•Solenoid spill valve: closed (energized)
Roller
Cam Plate

Injection Stroke PR0065

- 19 -
(3) End of Injection
When the solenoid spill valve is no longer energized,
its valve opens. The highly pressurized fuel in the
plunger is then pushed back into thepump chamber,
the fuel pressure drops, and the pumping ends. Solenoid Spill
Valve (open)
(4) Fuel Cutoff
When the fuel is cut off, the solenoid spill valve is not Roller
energized and its valve remains open. Therefore, fuel
is not pumped even if the plunger ascen ds. There are Cam Plate
also other systems that use afuel cutoff valve for this End of injection, fuel cutoff PR0066
purpose.

4. Fuel Injection Volume Control

4-1. Outline of Injection Volume Control
The computer has in its memory the basic injection volume data that was calculated based on
factors such as the engine speed orthe acceleration opening. Corrections based on factors such
as the intake air pressure, coolant temperature, or intake air temperature are added to the basic
injection volume. Then, the computer sends signalsto the solenoid spill valve in thepump in order
to control an optimal fuel injection volume. The special characteristic of the ECD-V3 (ROM) pump
is the phase correction that ismade based on the ROM that is mounted to the pump body.

Speed Sensor

Computer Solenoid Spill

Acceleration Sensor Valve

Venturi Opening Sensor

*
Water Temperature Sensor ROM

Intake Air Temperature Sensor

Fuel Temperature Sensor

Intake Air Pressure Sensor

Vehicle Speed Signal

To nozzle

Starter Signal

PS0041

*Or, correction resistors θ( resistors) on conventional type

- 20 -
4-2. System Components Vacuum Chamber
(1) Intake Air Pressure Sensor (containing silicon chip)
This sensor detects the intake air pressure by abso-
lute pressure* and sends it to the computer in the form
of an intake air pressure signal.
It is a semiconductor pressure sensor that utilizes the
property of the (silicon) crystal that is sealed inside
the sensor, whose electrical resistance changes when
pressure is applied to the crystal.
*Absolute pressure: a pressure at 0 vacuum Supercharging
Pressure PR0068

]
V
[
e
g
ta
l
o
V
t
u
p
t
u
O

Pressure [kPa {kgf/cm2}]

Sensor Output Characteristics ES0359

(2) Speed Sensor

The speed sensor is mounted so as to face the teeth of the pulsar (gear), which is pressed onto the
pump drive shaft. The sensor contains a magnet and a coil, and when the pulsar rotates, the mag-
netic flux that passes the coil increases and decreases, causing an alternate current voltage to be
generated in the coil. The computer counts the number of pulses to detect the engine speed. The
pulsar has 52 teeth, with 3 teeth missing at 4 locations. Thus, the pulsar rotation angle is detected
every 11.25°CA.

Speed Sensor ]
V [
Magnet e 360°CA
g
lta
Coil 11.25°CA
Roller Ring o
V
t
Missed u
tp
Tooth Area u
O

Pulsar Time
Sensor Output Signal

PR0070, PR0071

- 21 -
(3) Acceleration Sensor Fully Closed
The sensor for detecting the acceleration opening of Acceleration
the conventional ECD-V3 pump was mounted onthe Switch
venturi. However, some of the ECD-V3 (ROM) pumps
detect the opening at the accelerator pedal. With ei-
ther type, the voltage at the output terminal changes
in accordance with the acceleration opening, and the Acceleration
Sensor
idle condition is detected by the ON/OFF signal from
the idle switch.
This is a dual system that enhances control precision
and consists of the following: CS0926

a. Idle switch and acceleration fully closed switch

b. VA and VAS.

Internal Circuit QT0111

(4) Venturi Opening Sensor

(or throttle position sensor)
This sensor is mounted tothe conventional venturi or
the vacuum type independent venturi to detect the
valve opening that is necessary for controlling the
throttle.
On some types of engines, the throttle control is ef-
fected by the signals from the acceleration sensor,
instead of the venturi openingsensor. Vacuum Type
(See pages 49 and 50 for details on the throttle con- Venturi Opening
Sensor Independent Venturi
trol.) CS0917

Circuit VS0511

- 22 -
(5) Water Temperature Sensor
This sensor, which detects the coolant temperature,
contains a thermistor. The thermistor is a type of semi- Thermistor
conductor whose resistance changes significantly
according to the temperature. Thus, the coolant tem-
perature can be detected by the changes in the re-
sistance.

Construction PR0075

]
Ω
[k
c e
n
ta
s i
s
e
R

Coolant Temperature[°C]
Characteristics B6202

(6) Intake Air Temperature Sensor

This sensor contains a thermistor with the sametype
of characteristics as the water temperature sensor. It
is mounted on the intake manifold of the engine to Thermistor
detect the temperature of the intake air.

PR0077

(7) Fuel Temperature Sensor

This sensor contains a thermistor with the sametype
of characteristics as the water temperature sensor. It Thermistor
is mounted on the pump to detect thetemperature of
the fuel.

PR0078

- 23 -
(8) Solenoid Spill Valve (SPV)
The solenoid spill valve directly controls the injection Pilot Valve
volume. It is a pilot type solenoid valve that provides
Spill Passage Coil
high pressure resistance and high response. It con-
tains two systems, the main valve, and pilot valve sys- Main Valve
tems.
When the solenoid spill valve opens, the high pres-
sure fuel in the plunger returns to the pump chamber, Fuel Return
causing the injection of fuel to end.
In addition to the conventional type of solenoid spill Plunger
valve, there is also a direct-acting type that hasbeen Conventional Type PR0080
developed for higher spill performance (the ability of
returning the highand
pump chamber) pressure
higherinresponse.
the plunger backto the
Operation
Coil current ON: valve closed Direct-Acting
Type Valve
Coil current OFF: valve open
* See page 30 for details on the solenoid spill valve. Spill Passage
Fuel Return (to Pressure Chamber
pump chamber)
Plunger

Direct-Acting Type QT0281

(9) Correction Resistors (θ, τ) or ROM

The resistors, which are located on the side of the
injection pump body, apply a correction to the final-
stage injection volume value that is calculated by the
computer. The characteristic of the correction resis-
tor is that each must be selected according to its Correction
unique resistance value, while the ROM provides stor- Resistors
age for the correction data and the data can be eas-
ily rewritten.
ROM
PU0008

(10) Computer (ECU)

The computer determines the injection volume in ac-
cordance with the acceleration opening, engine
speed, and the signals from the sensors.

PR0081

- 24 -
 System Composition of Conventional ECD-V3

Intake Air
Solenoid Spill Temperature
Valve Sensor

Correction Resistors EGR

Valve VCV
Engine
Speed
Sensor
Throttle VSV
Valve

VSV
Crankshaft
Position
Sensor

VSV Water Temperature

Engine ECU Sensor

Intake Air
Pressure
Sensor
PS0043

System Composition of ECD-V3 (ROM) [Example on 3C-TE engine]

Accelerator Pedal Air Cleaner
Resonator
Reverse Shift Position Switch r
Acceleration Opening te
u
Acceleration Engine Speed p
m
Opening Fuel Temperature o
lC
Sensor ro
t
n
o VSV
C Turbo Charger
e
ni
g E-VRV (for throttle)
n
E
Venturi Opening Sensor E-VRV (for EGR) Oxidation Catalyst
Intake Air Temperature Sensor
Intake Manifold
EGR
VSV Valve

Intake Air Pressure Exhaust Manifold

Sensor Intake Manifold
Solenoid
Water Temperature
Spill Valve
Fuel Temperature Sensor
Sensor
Crankshaft Position Sensor

Timing Control Valve

Injection Pump

CS0924

- 25 -
4-3. Fuel Injection Volume Control
(1) Fuel Injection Volume Control Method Pump Chamber Solenoid
The start of fuel injection is determined by the pro- Spill valve
Cam Lift (open)
truded surface of the cam plate, as in the past. Ther e-
fore, the timing of the end of injection must be con-
trolled in order to regulate the volu
me of fuel injection.
In other words, the end of injection occurs at the time
the solenoid spill valve opens, allowing the high pres-
sure fuel to spill into the pump chamber.
A speed sensor is used for determining the timing in Cam Plate
which the solenoid spill valve opens, and the cam End of Injection PR0123
angle in proportion to the cam lift is detected inorder
to control the opening timing.
The diagram on the right shows the relationship be-
tween the timing in which the cam lift and the sole-
noid spill valve open and the injection volume. Start of Injection End of Injection

Cam Lift
Open
Closed Closed
Solenoid Spill Valve

Injection
Cylinder A
Cam Angle
Increased
Injection
Open
Closed Closed
Solenoid Spill Valve

Injection
Cylinder A

Injection Volume Control

PR0082

(2) Injection Volume Calculation

The computer calculates the injection volume that is optimal forthe operating condition of the engine.
To do so, it performs the following two calculations:
a. Basic Injection Volume
The injection volume that is theoretically necessary is calculated based on the acceleration open-
ing and theInjection
b. Maximum engine speed.
Volume
Corrections based on the intake air pressure, air temperature, and fuel temperature are added to
the injection volume that is determined by the engine speed, in order to calculate the maximum
injection volume while the engine is running.
The final injection volume is determined by selecting the lesser of the two injection volumes given in
a. and b. above.
- 26 -
[Reference: Fuel Injection Volume Speed Sensor
Control Method]
The fuel injection volume must be regulated by con-
trolling the timing of the end of injection, which is the Gear Cam Plate
timing in which the solenoid spill valve opens.
Solenoid Spill Valve Opening Timing
A speed sensor is used for determining thetiming in
which the solenoid spill valve opens, and the cam
Drive
angle in proportion to the cam lift is detected. Shaft
Therefore, Cam Plate Actuation PR0056
a. The cam lift is determined by the rotation angle of
the cam plate. The cam plate rotates in uniso n with
the gear that faces the speed sensor. Start of Injection End of Injection
b. Thus, the rotation angle of the cam plate can be
detected by the rotation angle ofthe gear, which is Cam Lift
the output of the speed sensor (that is output every Missed Tooth Area
11.25°CA). Cam Angle Signal
c. The computer uses the signals from the speed sen- Open
sor to determine the solenoid spill valve opening Closed Closed
Solenoid Spill Valve
timing (end of injection) based on the number of
teeth from the missed tooth area of the gear and Cylinder A
Injection

on the length of time. Cam Angle

Control at End of Injection PR0058
Note: The actual timing of the end of njection
i is determined by
adding the corrections based on the engine speed, ac-
celeration opening, and the signals from various sensors.
Example: 3C-TE Engine

12 13 0 1 2 3 4 5 6 7 8 9 10 11 12 13

Final Injection Angle

Closed
(ON)
SPV
open
(OFF)

Plunger Lift

PS0044

- 27 -
[Reference: Construction and Operation of
Solenoid Spill Valve (conventional type)] Main Valve Chamber Pilot Valve
(solenoid valve)
The solenoid spill valve, which consists of two sys- Main Valve
tems, the main valve and pilot valve systems, has the (automatic valve)
functions given below.
Note: The diagram shows a basic construction.
Restriction
Function
Seat
Main Spill Pilot Spill
Flow
Type Function PR0084
Volume
Automatic Spills the high pres-
Main Large Valve sure fuel in the
Valve (hydraulic plunger chamber to
type) end injection.
Creates a hydraulic
Pilot Small Solenoid pressure difference that
Valve Valve prompts the operation of the
main valve.

Operation
(1) Pressure-Feeding and Injection
The high pressure fuel in the plunger chamber passes through the restrictor to fill the main valve. At
this time, the fuel is injected from the nozzle. In this state, side Bof the right and left areasof the main
valve that receive pressure is larger than side A (in the diagram below), and the main valveemains r
completely closed.
(2) Pilot Spill
When the coil is no longer energized, the pilot valve opens and asmall amount of fuel flows out of the
main valve chamber. Therefore, the hydraulic pressure of the mainvalve chamber decreases.
(3) Main Spill
The main valve opens due to the difference in hydraulic pressures, and a large amount of fuel spills
from its seat area, thus ending injection.

[Cam Lift]
Solenoid Spill Valve Open Open
Closed

(1) &Pressure-Feeding
Injection (2) Pilot Spill (3) Main Spill
PR0085, PR0086, PR0087

- 28 -
[Reference: Construction and Operation of Solenoid Spill Valve (direct-acting type)]
Construction
A direct-acting type solenoid valve is used in order to achieve high levels of response and spill per-
formance.

Valve Body Core Coil

Spool Valve

Valve Body
Spring
Coil

Spool Valve Spring Armature

CrossSectionDiagram OutlineDiagram
QT0272, QT0273

Operation
(1) Pressure-Feeding and Injection
When theThis
the core. coil is energized,
causes the armature
the spool is pulled
valve to move andinto Chamber
To Plunger
come in contact with the valve body, thus making the
plunger chamber oil-tight. Then, the ascent of the
plunger causes the pressure-feeding andinjection of
fuel.

Pressure-Feeding and Injection

QT0274

(2) Spill and Suction

When the coil is no longer energized, the reaction of
the spring causes the spool valve to open, and the
fuel in the plunger chamber spills through the passage
in the spool valve, causing the injection to end. Also,
fuel enters the valve when the plunger descends.

Spill QT0275

- 29 -
 Solenoid Spill Valve Actuation Method
Because the solenoid spill valve must operate with
a quick response, the coil resistance is kept small
to ensure operating current, and current control is
effected to prevent overheating.

General Current PU0001

4-4. Relationship Between Vehicle (Engine) and Fuel Injection Volume Control
(1) Load Applied to Engine and FuelInjection Volume Control
The computer (ECU) determines the injection volume that is optimal forengine the load (vehicle operating
conditions) based on the two patterns that follow. One is the “basic injection volume” that is determined by
the addition of corrections (which are calculated from the sensorsignals) to the value that are based on
the
engine speed and the acceleration opening. The other the is “maximum injection volume” that specifies
the limit of the injection volume in proportion to the
air volume that is drawn into the engine.
Basic Injection Pattern (example) Maximum Injection Volume (example)
Changes by required volume
t) 100% t)
3
/s Full Load 3
/s
m m Intake Air Volume
…large
m ( 50% m (
e e
m m
lu Partial Load 30% lu
o o Intake Air Volume
…small
V V
iton Idle 10% 20% n
io
tc
c
e
j je
In In

Engine Speed (rpm) Engine Speed (rpm)

PU0002

(2) Flowchart for Calculating Injection Volume

ECU
Acceleration Opening Sensor
Basic Injection Volume
Speed Sensor
Intake Air Pressure Sensor Basic Maximum Injection Volume
Select the
Correction by
smaller injection Solenoid Spill Valve
Water Temperature Sensor resistor (or data)
volume
Maximum Injection Volume
Intake Air Temperature Sensor

Fuel Temperature Sensor Correction

θ Resistor or ROM
PS0045

- 30 -
4-5. Final Fuel Injection Volume Decision
g
(1) Other than starting in
n
e
The injection volume is determined by using the gov- p
O
ernor pattern of the map with the smaller injection ti
n
o
volume, after comparing the basic injection volume le
a
r
and the maximum injection volume. e
c
c
A
(2) Starting d
te
al
The injection volume is determined based on the basic u
m
i
injection volume, with corrections added in accordance S
with the starter and water temperature sensor signals. Coolant Temperature PS0046
If the coolant temperature is lower than the specified
value (10°C), a simulated acceleration openingis cre-
ated to calculate the injection volume.

4-6. Various Types of Fuel Injection

Volume Corrections t
(1) Intake Air Pressure Correction n
ie
ifc
The intake air volume is calculated based on the sig- f
e
o
nals from the turbo pressure sensor sothat the maxi- C
n
mum injection volume can be corrected towards the o
it
c
increase side if supercharging is occurring. Onsome e
rr
o
engine models, the correction coefficient is de- C
creased during the transitional period in which the
EGR and IDL (idle) switches are turned from ON to Intake Air Pressure Sensor Output Voltage (V)
OFF. PU0003

(2)
TheIntake Air Tvaries
air density emperature Correction when air is
by its temperature t
n
drawn in, and this causes a variance in the air-fuel ie
ic
ff
ratio. Therefore, the higher theintake air temperature, e
o
the greater the correction that must be made to reduc e C
n
ito
the injection volume, through the use of the signals from c
rre
the intake air temperature sensor. o
C

Intake Air Temperature(°C)

PU0004

(3) Fuel Temperature Correction

When the temperature of the fuel changes, its volume t
n
as well as the amount of its leakage during pumping ie
ic
changes. Therefore, the actual injection volume ff Varies by engine speed
e
changes and creates a variance in the air-fuel ratio. C
on
io
Therefore, the higher the fuel temperature, the greater t
c
e
the correction that must be made, in order to increas
e rr
o
C
the injection volume.

Fuel Temperature (°C)

PU0005

- 31 -
(4) Cold Temperature Correction
t
To improve the operation of a cold engine, a correc- n
ie
tion is made to enrich the air-fuel ratio by increasing ic
ff
the injection volume when the coolant temperature is e
o
C
low. After the correction starts, the injection volume is n
decreased at a prescribed rate. toi
c
e
rr
o
C

Coolant Temperature PU0006

(5) Deceleration Correction

When the vehicle decelerates suddenly as a result of )
A
sudden braking, the drop in the engine speed could C
(°t
cause the engine to stall or to operate poorly. To pre- n
e i
c i
vent this situation, this correction increases theinjec- ff
e
tion volume and allows the engine speed to decrease o
C
n
smoothly. ito
c
re
r
o
C Amount of Changes in Speed (rpm)
PU0007

(6) Injection Volume Correction

θ Resistors (or ROM)
These resistors or ROM data are used for adjusting the
phase ofthe cam angle(°CA) calculatedby the computer r
to
in order to make a cor
rection to the final injection volume. iss
In the case of correction resistors, the greater their R
e

resistance, the higher the VRP terminal voltage will θ

be, and the correction is made to increase the vol-

ume. However, if the VRP terminal voltage is abnor- A
C
°
(
)

mal, the fail-safe function uses the map data in the o

n
ti
c
computer to apply a prescribed amount ofcorrection. rre
o
C
In the case of the ROM, detailed data that is matched e
m
lu
o
to the characteristics of the individual pumps are ti
V
n
o

stored so that a more detailed and higher precision c

ej
In

correction can be applied. Furthermore, the data on

VRP Terminal Voltage (V) PU0009
the ROM can be rewritten in order to set finely tuned
correction values at will.
Adjusting Screw (SPV) Adjusting Screw (SPV)

* The dots indicate ROM data

θ Resistor

PS0048

- 32 -
(7) Idle Vibration Reduction Control
To reduce engine vibrations during idle, this control compares the time between the cylinders, and
regulates the injection volume for each cylinder if there is a significant difference so that the engine
can operate more smoothly.

Cylinder
3 Cylinder
4 Cylinder
1

PU0010

(8) Speed Correction Control of Injection Volume

When the speed of the injection pump increases, the fuel injection volume increases due to the re-
sponse lag of the solenoid spill valve. This correction is made because the fuel injection volume
varies by engine speed even if the injection angle remains the same.
)
(9) Gradual Control of Fuel Injection Volume %(
g
This control makes a correction so that the engine in
n
e
accelerates smoothly, instead of increasing the injec- p
O
n
o
tion volume in accordance with the acceleration open- ti
ra
e
ing. It prevents the emission of black smoke or poor e
l
c
c s
e No correction (dotted line)
operation due to the sudden increase in the fuel in- A
e
a
re
c
n
jection volume during acceleration. Conversely, dur- u
m
l
o
I

V
ing deceleration, this control gradually decreases the o
ti
n

injection volume in order to minimize the torque fluc- c

e
j
In
tuation. Time
PU0011

(10) ECT Control (on automatic transmission vehicles)

This control reduces the shocks that result from the torque fluctuations that occur during the shifting of
an electronically controlled transmission (ECT). oT do so, this control momentarily reduces thepower
of the engine by reducing theinjection volume during shifting.

- 33 -
4-7. Summary of Injection Volume Control
n
o
it n
ra tio l
e c o
c
l
e rr
e tr
e o n
D C o
C
d
* n e
e g o
ti e
lv in c p
a rn re S
r
V C e a o
r o le
lil IS L C s
n Id
p e :
S n S C
id o
ti
E
N IS
*
o d c
e
n e rr
e
l e
p o
o S C -
S ra
: e
PV m rn re p
e ro
s
S lu tt
e
d tu o
n m n
e
o a e
e ra g
in
ti e
T S
V m
e
e c
l
rP
u
p rn rre
l
n o
p
l
e e er
v m a u
io o tu
o
tc
d
e S u
F
e
T
e
L C F
rn
ir
u
q e -
l
o je e e
r n
i e a
r
tr v y
g
l m
e
In
e
o
b lu
n e u
p r
n
s F o
n
e i o
o m G g
n E g
n
m
u
V
n o
ti
n m
e s
n
C
a
io c T
u
E
h
C im c
t e
rr r e
g ld x
a e j e
t S
im
o o
ni C M In C a re
x
e mul oVnoit cej nI
m W ut
i a e
r
T tu n -
F M ri o r
F A ra ti
c m o
e e e s
O k p re T n
a t m r ri e
g e o S
ni In T C A e
rt r ri n e r
tu
ta e
ll A re m
u
o
it k a
s u c a r
n a r e
k s
s
m
ix re
t
n e
a
h ms le
l ta
In
re a r
o I p
e tre e n
a P M C
m h h
t ri
re o ms
lu tO t
m
u A u ti
c e
o c m
ix ek s
s re h s
-
V el a at e r
o t e
n e n r t e
s
d
o r
M I P C c a ri P r
tio
c S le
e
B
n e
P
t n ir
A
s
o
n
je g S io
t n
ie tio e
e
S
n
Il n n
c
e s c
e k
ri o rr n rr a
t re
a u ti o ra o n u
l d a I s
in a l e
r C T C
F r u
d ro
t
l
e
g e ra n c
rg o e
tin
r la
G c d el
tt
n
tio
r
o
s
a o i
t e g
n
r s
o
n
e
S h
t i h
tc rt T P S
at
le s
e e n C°
d a 0
m S a h 1

rt r
e
o
lu
r
n o
lL
u
o r l d e t
ra s
n
e u e th
tt
e
V e
a
F d
a
e O m
p
S
n p
o
te m
E
L
u
tio P
l

r
a
it
r
S r
e im
N r N
t O e
a

c o
P
e a in
r rt
je n n
i
W m
e
r g g
tr e ta
n
I e e
l n a S
tin
t im
v d
I E
ic
S T
o r
s r G a
t
a e
ll S
B
e mul oVnoit cej nI
a
m C
es °
0
1
ht re re
t l u d
to
n
tu
c o
rt
t te i
ra r
e
l ra la ra g r e o
n n e le in
e o io p u e n e
t p
a m n
s
S c
l
t
ra
m im c
c
e
p WeT S
e
a te m S A O
u
d
g le r u
a in
r
e
c e im
r u c t x
G d a a a PU0012
W m

- 34 -
[Reference: Maximum Fuel Injection Volume Calculation Flow Chart]

Detect engine speed

Calculate basic maximum fuel

injection volume

Detect intake air pressure

Regulate injection volume

Detect intake air temperature

YES
High intake air temperature Reduce injection volume

NO

Detect fuel temperature

YES Increase injection volume com-

High fuel temperature
mand value
NO

Determine maximum injection

volume

PS0049

- 35 -
5. Fuel Injection Timing Control
5-1. Outline of Fuel Injection Timing Control
The computer detects the conditions of the engine in accordance with the signals receive d from the
sensors. Then, it calculates the injection timing that is optimal for those conditions. The results are
then sent to the timing control valve (TCV) in order to control the injection timing.

Turbo Pressure Sensor Computer

Acceleration Sensor
ROM
Speed Sensor

Crankshaft Angle Sensor

Water Temperature Sensor

Intake Air Temperature Sensor

Vehicle Speed Signal

Starter Signal Timer Piston

Timing Control Valve

PS0050

5-2. Components
(1) Crankshaft Position Sensor
This sensor is mounted on the engineblock, and a protrusion is provided onthe crankshaft to gener-
ate one pulse per revolution of the engine.
These pulses are then sent to the computer in the form of standard crankshaft position signals.

Coil Magnet

(2) Construction

Protrusion
Crankshaft Position
Sensor

To ECU 360°CA

Cylinder Block (3) Output Signal

(1) Installation
PR0094, PR0088, PR0089

- 36 -
(2) Timing Control Valve (TCV)
The timing control valve (hereafter referred to as “TCV”), which is mounted on the injection pump,
opens and closes the fuel passage between the high-pressure and low-pressure chambers of the
timer piston in accordance with the signals from the computer.
When current is applied to the coil, the stator core becomes magnetized and retracts the moving
core by compressing the spring. As a result, the fuel passage opens.
The opening of the valve is controlled by the computer in accordance with the ratio of the ON/OFF
times (duty cycle ratio) of the current that is applied to thecoil. The longer the length of the ON time,
the longer the valve remains open.

Coil
High-Pressure t
n
e
rr
u Average Current Large
C
Low-
Pressure
t
n
e
Moving Core rr Average Current Small
Spring u
C
Time
Stator Core
(1C
) onstruction (2)DutyCycleControl
PS0051, PR0095

5-3. Injection Timing Control

(1) Injection Timing Control Method
The injection timing is determined by the valve opening time of the TCV that regulates the pump
chamber fuel pressure (that is applied to the timer piston) and by moving the roller ring to effect
control.
The longer the valve opening time of the TCV, the greater the volume of fuel that bypasses from the
high-pressure side of the timer piston to the low-pressure (suction) side. Therefore, the spring force
moves the timer piston in the retard direction.
When the valve opening time of the TCV is short, the timer piston moves in the advance direction.
Roller Ring

Pump Chamber
Fuel Pressure
Low-Pressure
Computer

Advance Retard

Timer Piston Timing Control Valve PR0091

- 37 -
(2) Injection Timing Calculation
Based on the target injection timing (target crankshaft position), the computer makes corrections in
accordance with the signals received fromthe sensors in order to calculate the injection timing that is
optimal for the operating conditions of the engine. Furthermore, the computerutilizes the crankshaft
position signal (TDC) from the crankshaft position sensor to calculate the actual crankshaft position,
which is then fed back to the target injection timing.
a. Target Injection Timing
The target injection timing is calculated based on the acceleration opening and engine speed.
b. Injection Timing Correction
The injection timing is corrected based on the intakeair pressure and coolant water temperature.
c. Starting Injection Timing

During starting,
ant water the target
temperature, andinjection
engine timing
speed.is corrected in accordance with the startersignal, cool-

Example: 3C-TE Engine

(TDC)
Crankshaft Position
Sensor Signal
t

12 13 0 1 2 3 4 5 6 7 8 9 10 11 12 13
NE

PS0052

(3) Target Injection Timing and Final Injection Timing Calculation Flow Chart

ECU
Acceleration Opening Sensor
Basic Target Injection Timing Target Injection Timing Timing Control Valve
Speed Sensor

Intake Air Pressure Sensor Correction Comparison and Correction

Water Temperature Sensor

Crankshaft Position Sensor Actual Injection Timing

τ Resistor or ROM

PS0053

- 38 -
[Reference]
Feedback Control
This function effects control on the timing angleθ between the actual compressiontop-dead-center
and the start of injection, as shown in the diagram. However, the actual compression top-de
ad-center
and the injection waveform cannot be detectedin the form of signals. Therefore, the actual injection
timing must be calculated as follows.
(1) Actual Injection Timing Calculation θ
a. On the engine, there is a correlation between the Actual
compression top-dead-center and the TDC signal Compression
of the crankshaft position sensor. TDC 1
θ Engine
b. Also, on the pump, there is a correlation between
TDC Signal
the injection waveform and the NE pulse of the
speed sensor.
c. Therefore, the actual injection timing can be ob- NE Pulse
tained by calculating the phase differenceθ 1 be- Pump
Injection
tween the TDC signal and the NE pulse. Waveform
(2) Feedback Control PR0092
This function corrects the duty cycle ratio of the TCV
so that the actual injection timing matches the target
injection timing.

Relationship Between Injection Timing and

Injection Volume Speed Sensor
Roller Ring
The injection timing is controlled by varying the posi-
tion of the timer piston, which is linked to the roller Pulsar
ring that determines the startof pressure-feeding. (52 teeth)
Thus, the ending injection timing also advances in the Drive Shaft Missed
same amount that the starting injection timing has Tooth Area
advanced. Therefore, the injection volume is notaf-
fected by the injection timing. Timer
The changes in the position of the roller ring do not Piston
alter the relationship between the cam lift and the
NE PR0083
pulse, which is associated with theinjection volume
control. This is because the speed sensor ismounted
on top of the roller ring and moves in unis
on with the
roller ring.

- 39 -
5-4. Final Injection Timing Decision
(1) Other than starting Acceleration
A
) Opening
Target injection = basic targetinjection timing •iŠp“x
C (large)
(°
+ cold correction advance e
l
+ intake air pressure correctionadvance g
n
A Acceleration
e
c
n Opening (small)
(2) Starting a
v
d
A
Starting target injection = starting basic target crankshaft position Engine Speed (rpm)
+ starting water Basic Target Injection Timing
temperature correction PU0013

5-5. Fuel Injection Timing Correction

(1) Intake Air Pressure Correction Advance A
)

The amount of correction advance is calculated based C

(°
c
e
on the intake air pressure sensor signal (intake air v
n
a
d
pressure) and the engine speed. n
A
o
ti
c
e
rr
o
Reference: Other Specifications C
re
u
Model ECD-V3 ECD-V3 s
s
re
P
Engine 1KZ-TE 3C-TE ri
A
e
k
Maximum Correction Advance 6°CA 5°CA ta
In

0°CA condition 3200 rpm minimum 4000 rpm minimum PS0054

(2) Cold Correction Advance

The amount of correction advance is calculated based )
A
8
THW -40
on the water temperature sensor signal (coolant wa- C
°
(
e
c 6
n
a
ter temperature) and the engine speed. On some v
d
engine models, the calculation is made through inter- A
n
ito
4 THW 0

polation in accordance with the map data in the ECU. e

c
rr
2
o THW 20
C
dl THW 40
o
C 0

0 1000 2000 3000 4000 rpm

(°CA)
NE (rpm )
800 1200 1600 2000 2400 2800 3200
THW (oC)
-20 13.0 13.8 14.4 12.0 8.0 4.2 0.0
-10 12.0 13.6 14.0 10.6 4.6 1.4 0.0
0 12.0 12.6 11.0 5.8 0.2 0.0 0.0
10 7.0 8.6 10.0 3.6 0.0 0.0 0.0
20 5.8 7.4 9.0 1.2 0.0 0.0 0.0
30 4.4 6.4 8.0 0.2 0.0 0.0 0.0
40 3.2 6.2 6.4 0.0 1.0 0.0 0.0
50 3.0 4.8 5.0 0.0 0.0 0.0 0.0
60 2.8 3.8 3.8 0.0 0.0 0.0 0.0
70 0.0 0.0 0.0 0.0 0.0 0.0 0.0

Map data in ECU

PS0055

- 40 -
(3) Starting Duty Cycle Ratio
When the engine has just been started and its speed
is low, theTCV is actuated by the duty cycle ratio that )
is determined by the coolant water temperature. At (%
e
l
this time, the lower the coolant water temperature the c
y
smaller the duty cycle will be, causing the injection C
y
t
timing to advance. In particular, when the engine ex- u
ceeds the specified speed, a correction based on D
water temperature will be applied to the “starting tar-
get injection timing”.
Coolant Water Temperature °(C)
PU0014

(4) Starting Basic Target Crankshaft Position

After starting, when the engine speed increasesto a )
A
C
°
certain level, the basic targetcrankshaft position that (
o
n
i
is predetermined according to speeds is applied. it
s
o
P
tf
a
h
s
k
n
ar
C
t
e
g
r
a
T
ic
s
a
B
Engine Speed (rpm)
PU0015

(5) Starting Water Temperature Correction A

)

When the coolant water temperature is low, a correc- n

C
°
(

tion is applied to the starting target injection timing. o

tii
s
o
P
ft
a
h
s
k
n
a r
C
t
e
rg
a
T
g
in
rt
ta
S
Coolant Water Temperature(°C)
PU0016

(6) Crankshaft Position Correction Resistor

τ (or ROM)
The NE pulse (cam angle signal) that is detected by
the speed sensor is used for controlling the injection Injection
timing. However, a deviation in the correlation be- Waveform
tween the cam angle signal and the injection wave-
form that exists between the individual pumps causes Pump A

the injection
therefore timing to
corrected also deviate.
through the use This
of thedeviation is Ne Pulse
correction Pump B
resistor τ or the correction data on the ROM.
Deviation
PS0056

- 41 -
5-6. Timing Control Valve (TCV) Actuation Method
(1) Fixed Duty Cycle Control )z
When the engine is being started (starter turned ON, H
(
y *
and engine operating at low speeds), theengine has c
n
stalled (ignition switch turned ON), or the crankshaft e
u
q
position sensor is defective, the TCV is actuated in er
F
l
accordance with the duty cycle ratio that is fixed to o
tr SPV Synchroni-
the actuation frequency that has been prescribedfor n
o zation Control
the respective condition. C Fixed Duty
V Cycle

(2) SPV (Solenoid Spill Valve) Synchronization C

T
Control Engine Speed (rpm)
Wheninthe
sure theTCV is causes
pump turned from ON to which
pulsation, OFF, the fuel pres-
affects the * On ECD-V3 (ROM), synchronization control
is effected even when the frequency is
injection volume and injection timing. Therefore, the greater than 40Hz. PU0017
TCV operation is synchronized to the actuation of the
SPV at engine speeds other than the prescribed
speeds. As a result, the influences of the pulsation
are minimized.
(3) Ordinary Control
The TCV is controlled by varying the duty cycle ratio
in accordance with the operating conditions, except
when it is under fixed duty cycle control or SPV syn-
chronization control.

- 42 -
5-7. Summary of Injection Timing Control (representative examples)

Final Duty Cycle TCV

Duty Cycle Control

t
n
e
lu
Integral Amount u
m
o Proportional Correction Amount
a A
V n
n io
io
t t
c
c e
e r
rr r
o
o C
C
l l
a r
a
n
g o
ti
e
t
In p
r
o
ro
P

Target Crankshaft Position - Actual Crankshaft Position Target CrankshaftPosition - Actual Crankshaft Position

Difference

Target Injection Actual Injection

Timing Timing

Intake Air Pres-

sure Correction Basic
TimingInjection Speed
Correction Cold Advance
Correction

e
c
n e
v
a c
d n Water Temperature
A a
n v
o d
ti
r
c
e A -24°C
r n
o
o
C
ti
r e
c
rre
u
s
s
e
r
P
o
ir C
ld
A
e
k
a
o
t
In
C

Intake Air Pressure Sensor Voltage (V) Engine Speed (rpm)

Intake Air Pres- Throttle Posi- NE Water Tempera- TDC NE

sure Sensor tion Sensor Sensor ture Sensor Sensor Sensor

PU0018

- 43 -
[Reference: Fuel Injection Timing Calculation Flowchart]

Detect engine speed

Detect fuel injection volume

Basic injection timing advance

Detect water temperature

Low water YES

temperature
Basic injection timing advance

Detect intake air pressure

Low intake YES

Basic injection timing advance
air pressure

NO

Detect crankshaft position and

Decide target injection timing
camshaft position

Detect actual injection timing

Compare target
Advance injection timing
Retard
and actual
injection timing

Equal

Control the timing control Control the timing control Control the timing control
valve to retard valve to remain as is valve to advance

Fuel injection timing

PS0057

- 44 -
6. Idle Speed Control
6-1. Outline
The computer calculates the target speed in accordance with the operating conditions of the engine
and determines the injection volume in orderto control the idle speed.

<Sensor> <Computer> <Actuator>

Speed Sensor

Acceleration Sensor

Water Temperature Sensor

Idle Speed
Vehicle Speed Sensor Control Solenoid Spill Valve

Starter Signal

Air Conditioner Signal

Neutral Start Switch

PS0058

6-2. Idle Speed Control

(1) Feedback Control
The computer compares the target idle speed and the engine speed (speed sensor signal) at that
time.target
the If a difference exists, the computer controls the injection volume so that
idle speed. the engine speed matches
Example of Idle Speed (3C-TE engine)
The ON/OFF (air conditioner signals) conditions of the air conditioner are detected to control the idle
speed.
•Air conditioner ON: 850 rpm
•Air conditioner OFF:750 rpm

(2) Warm-Up Control

In accordance with the coolant water temperature, this function controls the engine to a fast idle
speed that is optimal for warming up the engine.
In addition, the computer effects “prospective control” in which the idle speedis changed beforehand
only for a prescribed amount. Thisprevents the idle speed from fluctuating due tothe changes in the
engine load, such as when the air conditioner is turned ON or OFF.
There is also an idle vibration reduction control function that corrects the injection volume of the
cylinders by detecting any speed fluctuations per cylinder.

- 45 -
7. Intake Air Venturi Control
This control regulates the intake air volume by controlling the sub-valve in the venturi, which is pro-
vided in the intake manifold, in three stages:fully open, half open, and fully closed. Some pumpsare
provided with a single-valve type that uses only the main valve, such as the vacuum type independent
venturi or the electronically controlled type that uses a stepmotor.
7-1. Function
Component Name Function
Actuator (dual-stage actuator) Opens and closes the sub-valve.
VSV Switches the vacuum and atmospheric pressure that is applied to
the dual-stage actuator.

Throttle Position Sensor Detects the acceleration opening.

Speed Sensor Detects the engine speed.
Water Temperature Sensor Detects the coolant water temperature.
Engine Control Computer Sends signals to the VSV and opens and closes the sub-valve in three stages.

7-2. Construction Diaphragm

(1) Venturi
The standard types of venturis are the dual-valve type
that contains main and sub valves, and the single-
valve type that contains only the mainvalve.
In the case of the dual-valve type, a throttle position
sensor, which detects the throttle opening, is mounted
on the main throttle valve. (In case of thesingle-valve
Throttle Position
type, the sensor is also mounted on themain valve.) Sensor
Venturi (dual-valve type)

Throttle Position Sensor Vacuum Type

(Venturi Opening Sensor) Independent Venturi
(single valve type)
PU0019, CS0917

(2) VSV
VSV1 (diaphragm chamber A)
Switches the vacuum and the atmospheric pressure VSV2 (diaphragm chamber B)
that is applied to the actuator in accordance with the
signals from the engine control computer (ECU).
Specifications air passage e
r
e
PortE PortF Atmospheric Port h
p
s
ON o
tm
OFF A

QN0017

- 46 -
7-3. Operation
(1) Cold, Fully Closed Acceleration, and High-Speed Operation
The engine control computer detects the coolant water temperature inaccordance with the signals
from the water temperature se nsor. When the engine is cold, it turns OFF both VSV 1 and VSV2. This
introduces atmospheric pressure to both chambers Aand B in the actuator, allowing the sub-val ve to
open fully. As a result, practically no restriction will be applied tothe intake air volume during idling.

Actuator Chamber B Chamber A

Atmosphere

Main Sub Vacuum Pump

Accelerator Pedal Valve Valve
VSV1
VSV2

Atmosphere
Engine Acceleration Opening
Control Engine Speed
Coolant Water Computer Ignition Switch
Temperature
QN0018

(2) Normal Driving (after warm-up)

After the engine has warmed upat idle, the engine control computer turns VSV1off, and VSV2 ON.
This
pumpintroduces atmospheric
to chamber pressure
B. As a result, to chamber
the sub-valve A intothe
opens actuatorextent
a certain and vacuum from the vacuum
(half open).

Actuator Chamber B Chamber A

Atmosphere

Main S u b Vacuum Pump

Accelerator Pedal Valve Valve VSV1
VSV2

Atmosphere Acceleration Opening

Engine
Control Engine Speed
Coolant Water Computer Ignition Switch
Temperature

QN0019

- 47 -
(3) Stopping the Engine
When the ignition switch is turnedOFF, the engine control computer turns ON VSV1 and VSV2. This
introduces the vacuum from the vacuum pump to chambers A and B in the actuator.As a result, the
sub-valve closes fully.

Actuator Chamber BChamber A

Atmosphere

Main Sub Vacuum Pump

Accelerator Pedal Valve Valve VSV1
VSV2

Atmosphere Acceleration Opening

Engine
Control Engine Speed
Coolant Water Computer Ignition Switch
Temperature
QN0020

- 48 -
[Reference: Single-Valve Type Venturi Intake Restriction Control (Example:
Vacuum Type Independent Venturi)]
Outline
In contrast to the dual-valve type that contains a main Main Actuator Fully Open
valve and a sub-valve in the venturi, this type controls
the intake air with a single throttle valve (main valve).
Basic Control
Throttle Valve Condition Control Actuator Control Valve
Idle ⇔ Fully Open Main Actuator E-VRV
Fully Closed Main & Sub-Actuators E-VRV, VSV Link

Sub-Actuator PS0059

Throttle Valve Opening and Operatin Conditions

(1) Fully Open Idle⇔Fully Open
•Starting (starter signal: ON)
•During driving (fully open acceleration during rapid
acceleration)
•Outside air temperature 10°C maximum
(2) Between idle⇔fully open (partial acceleration)
•During warm-up (coolant water temperature 59°C
maximum)
•During driving (after warming up completely, idle
switch: OFF) PS0060

(3) Idling
•Idling after warm-up Idle
•Engine stalling

PS0061

(4) Fully closed

•Engine stopped (ignition: OFF) and immediately Fully Closed
thereafter
•When an abnormally high engine speed isdetected
•When the computer
•When the solenoid spill valve ismalfunctioning
is malfunctioning

PS0062

- 49 -
[Reference: Singel-Valve Type Venturi Intake Air Restriction ontrol (Exam-
ple: Electronically Controlled Type Venturi [made by another company]
Outline Fully Open Position
This is a type of vacuum-controlled venturi that has Detection Switch
adopted a step motor to make an electronically
controlled venturi.
(1) Intake Air Restriction Valve
The newly developed electronically controlled intake
air restriction mechanism uses a step motor, which is
controlled by the control unit, to actuate the intake air
restriction valve in order to achieve high-precision and
optimal EGR
the engine volume inthis
is stopped, all operating ranges.
valve closes When
fully to allow Fully Closed
the engine to stop smoothly.
Step Motor Intake Air
Not e: To prevent the throttle valve position from Restriction
becoming altered, this part cannot be Valve
disassembled.

Fully Open
QT0363, QT0364

(2)
TheStep
coil inMotor
the motor is energized in accordance with
the signals received from the engine control computer.
The motor then rotates the magnet (rotor) in order to
precisely control the opening of the intake air restric-
tion valve. Coil
a. Specifications
Magnet
Type 4 phase, 32 pole (permanent
Actuation System 2 phase excitation, 1-2 phase excitation Stator magnet)
2 phase excitation 1°
Resolution [1 step]
1 - 2 phase excitation 0.5°
Amperage 1.2A per phase maximum
Coil Resistance 20 ± 2 Ω per phase
Insulation Resistance 10 Μ Ω minimum

Circuit
QT0365, QT0366

- 50 -
b. Construction
The step motor consists of two layers, and contains
two coils, four stators, and magnets that function as a
rotor. A stator contains eight tabs, and byhaving coils
placed between them, 16 poles of magnets are ar-
ranged alternately.
S N S N
The two layers of magnets are staggered 11.25° from
each other, resulting in a total of 32 poles that actuate
the rotor. Rotor (Magnet)
Each coil has two sets of coils that are wound in op-
posite directions, resulting in the two coils having four Coil Stators
phases.
The current
switched that is
in order to applied
change to
thethese coils
polarity is then
of the stators,
thus controlling the rotation and stopping of the rotors. Stators

QT0367

Energized

QT0368

c. Operation
Operation Diagram 1:
When current is applied tocoil A, an N-pole magnetic
field is generated at the top ofthe coil, and an S-pole
magnetic field is generated at the bottom of the coil. Stator A
Consequently, an N-pole magnetic field is induced at Coil A
stator A and an S-pole magnetic field is induced at Coil A’
stator A’. Similarly, when current is applied to coil B,
Stator A’
because it is wound in the opposite direction, an S- Stator B
pole is generated at the top of the coil, and an N-pole Coil B
is generated at the bottom of the coil. Then, stator B. Coil B’
becomes the S-pole and stator B’. becomes the N
pole. At this time, the S-pole of the rotor becomes Stator B’
positioned between the N-pole of stator Aand the N-
pole of stator B’.
•ì“®•}‚P Diagram 1
Operation
QT0369

- 51 -
Operation Diagram 2:
If current is applied to coil A’ without changing the cur-
rent that is applied to coil B, the top of coil A’ becomes
the S-pole and the bottom becomes the N-pole. As a
result, a magnetic field of the S-pole is induced to sta-
tor A and of the N-pole to stator A’. Coil A
The rotor that was positioned in operation diagram 1 Coil A’
rotates upon receiving the reaction force of the polar-
ity changes of the stators.
Coil B
Coil B’

Operation Diagram 2
QT0370

Excitation 1 Excitation 2 Excitation 3 Excitation 4 Excitation 5 (1)

Polarity of Stator A N S S N N
Coil A ON ON ON
Coil A’ ON ON
Polarity of Stator A’ S N N S S

Operation of
← →
Rotor 11.25°
phase
Polarity of Stator B S S N N S
Coil B ON ON ON
Coil B’ ON ON
Polarity of Stator B’ N N S S N
QT0371

- 52 -
8. EGR Control
As part of the countermeasures against exhaust gas emissions, this function recirculates a portion of
the exhaust gases by introducing it into the intake air inaccordance with the operating condiions. The
resultant slowing of combustion helps to restrainthe generation of NOx.

Vacuum Pump

Intake Manifold Vacuum Damper

Intake Air
Pressure Sensor
Engine Water Temperature
Control Sensor
Engine Speed
EGR Valve Computer Sensor
E-VRV

Throttle Position
Sensor

Engine Exhaust Gas

PU0020

Based on the acceleration opening (throttle position sensor), engine speed, coolant water tempera-
ture, intake air pressure,
the recirculation and intake
of the exhaust airand
gases temperature signals, thecontrol
effects duty-cycle computer determines
in the operation the volume
of the of
vacuum
control valve (E-VRV).

8-1. Construction & Operation of Com-

ponents
(1) E-VRV To From
It is an abbreviation for the “ElectricVacuum Regulat- EGR valve vacuum
pump
ing Valve”, a switching valve that is actuated electri-
cally.
Upon receiving 500Hz duty cycle signals from the com-
puter, the E-VRV supplies the vacuum from the vacuum
pump to the diaphragm chamber. Atmosphere

PU0021

- 53 -
(2) EGR Valve
The EGR valve consists of a diaphragm, spring, and From E-VRV
a nozzle. When the vacuum that is applied to the dia-
phragm chamber increases, the diaphragm moves
upward (in the direction to compress the spring). The
nozzle then opens in unison with this movement, al-
lowing the exhaust gas from the exhaust manifold to Intake Air
enter into the intake manifold. Manifold

Exhaust Manifold PU0022

8-2. Determining the EGR Volume

(1) Other than Idle
A correction based on the coolant water temperature and the intake air pressure condition is added
to the basic duty cycle value that is stored in the computer in order to determine the final duty cycle
value, which controls the E-VRV. However, control will be stopped if the final dutycycle value is too
small, or if the acceleration opening is too large.
(2) Idling
The final duty cycle value changes in accordance with the ON/OFF condition of the air conditioner.
Control will be stopped during starting, when the engine speed is low, or the coolant water tempera-
ture is low.
8-3. EGR Correction Coefficient
A correction is made to the basic duty cycle value in t
n
accordance with the coefficient that is obtained from ic ie
the water temperature sensor and intake air pressure ff
e
o
sensor signals. (The diagram on the right gives an C
example of a correction coefficient.) n
ito
c
e rr
o
C

Coolant Water Temperature(°C)

PU0023

t
n
ic e
if
f
e
o
C
in
ot
c
e
rr
o
C Intake Air Pressure (mmHg)
PU0024

- 54 -
9. Glow Plug Control
This control turns ON the glow plugs to warm up the air in the combustion chamber during cold start-
ing, while the glow plugs also serve as the source of the ignition of fuel in orderto facilitate starting.
Ceramic glow plugs are used as heat sources in order to simplify the system.

er
u e
c re
t r
ra r u tu
e o o a
r
p s S e
mn t p
e e a m
T e e
r S H T
te
a
W

Heat Generation Time (seconds)

PU0025

9-1. Glow Plug Indicator Illumination

Time Control e
When the ignition switch is turned ON, this control illu- im )s
T
minates the glow plug indicator light only for the length n d
n
o
ti o
of time that is determined by the coolant water tem- a c
n
i e
perature. The light goes out when thestarter is turned m
s(
ON. lu
Il

Water Temperature (°C) PU0026

9-2.
WhenGlow Plugswitch
the ignition Relay Control
is turned ON, this control en-
ergizes the glow plug relay to effect pre-heating only
e e
for the length of time that is determined by the coolant im im )
water temperature. When the starter is turn ed ON, the T) T s
g s d g d
n
glow plug relay is energized during that time. tin n
o ti n
o
a c
a c e e
After the engine starts and the starter is turned OFF, e e
H
-r s ( - s
H (
this control effects the after-heating control from that te re
f P
point. A

Water Temperature (°C) PU0027

Glow Plug Control Time Chart

Illuminate

Pre-Heating After-Heating
PU0028

- 55 -
10. Other Controls (the control specifications vary by engine type)
(1) Main Relay Control
Controls the relay for the main powersystem. (It does not control the computer’s ignition switch termi-
nal, battery terminal, and the power to the glow plugs.)
(2) Air Conditioner Cutoff Control
With the air conditioner turnedON, if the vehicle speed andthe acceleration opening become higher
than the specified value, this control determines that the vehicle is being accelerated, and turns OFF
the compressor for 3 seconds in order to lighten the load.
(3) Turbo Indicator Control
When the signal of the intake air pressure sensor exceeds a specified value, this control determines
that the turbocharger is operating and illuminates the turbo indicator light in themeter.
(4) Engine Stall Control
When the stalling of the engine is detected, this control stops controlling the SPV, actuates the timing
control valve at a fixed duty cycle ratio, andcontrols the sub valve to open half way.
(5) SPV Relay Control
When the engine speed is determined to have increased above a specified value, this control turns
OFF the SPV relay and fully closes the sub-valve to prevent the speed from increasing further.
(6) Low Water Temperature Lockup Prohibition
When the coolant water temperature is low and the vehicle speed is below a specified value, this
control outputs a lockup prohibition signal to the ECT (electronically controlled transmission) com-
puter.
(7) Communication Control with TRC (Traction Control) Computer
When the TRC is operating, this control receives signals from the TRC computer in order to reduce
the fuel injection volume and decreasethe output.
(8) Overheat Control

When
this the coolant
control water
reduces temperature
the fuel injection is higher and
volume thanretards
a specified value, and
the injection the in
timing engine
ordersp
toeed is high,
prevent the
engine from overheating.

- 56 -
11. Diagnosis Function
This is a self-diagnosis function of the system. If an abnormal condition in a signal system of the
respective control system is detected through sensors, the computer stores the malfunctioning sys-
tem in its memory. Because codes are assignedto the signals for every system, the computer stores
those codes in its memory. Then, it outputs the code of the system that is malfunctioning via the
diagnosis connector that is provided on the vehicle. In some systems, the indicator light in the meter
flashes to alert the driver. During troubleshooting, proper diagnosis can be made by reading the
codes that are output by the diagnosis connector.
Examples of DTCs (Diagnostic Trouble Codes)
DTC number 13: speed sensor system
DTC number 22: water temperature sensor system

Examples of output signals

(1) Normal

(2) Abnormal

DTC number 13 DTC number 22

PR0097

12. Fail-Safe Function

If an abnormal
continues signal
to use is output
that signal by a sensor
to effect control,and if an enginedmalfunction
a predetermine value that iscould result
stored if the
in the systemis
computer
used to effect control. Depending on the symptom, this function could alsostop the engine.
Example of Fail-Safe
a. Speed Sensor Signal System
If a signal is not input from the speed sensor, this function cuts off the current that is applied to the
solenoid spill valve in order to stop the injection of fuel.
b. Water Temperature Sensor Signal System
If the signal from the water temperature sensor is open orshorted, this function uses a predetermined
value that is stored in the computer.

- 57 -
Reference: Diagnosis Codes (ex.3C-TE engine) N.A. No Application
Diagnosis Contents n y
r
e Diagnosis Item toi
o Main Symptom
a
d (a:Condition, b:Abnormality state, c:Abnormality period) p in m of Malfunction
o (terminal symbol) mm e Inspection Area
C a u
Normal Mode Check (Test) Mode L Ill M
Revolution signal a:Engine revolution over 400 a:Engine revolution Loud  Wiring harnesses and
system1 rpm over 400 rpm knocking connectors (TDC signal
[TDC+, TDC-] b:No input of crankshaft b:Two revolutions of sound/Poor system)
12 angle signal (TDC signal) engine resulting in drivability • Center of crankshaft
crankshaft angle position
signal (TDC signal) • Engine control computer
other than 2
Revolution signal a:Engine revolution over 680 a:Engine revolution Engine • Wiring harnesses and
system 2 rpm over 680 rpm stalling / connectors (NE signal

13 [NE+, NE-] b:No input

c:Over 0.5 of NE signal
second b:One-half
of enginerevolution
resulting Unable
restart to system)
• Diesel revolution
a:During cranking in NE signal pulse sensor
b:No input of NE signal count other than • Engine control computer
c:Over 2 seconds normal
Timing advance a:After engine is warmed up, Loud • Wiring harnesses and
control system during driving knocking connectors (TCV signal
[TCV] b:Actual control value sound/Poor system)
14 deviates from target drivability • Timing control valve
timing advance value. • Clogged fuel filter
c:Over 20 seconds •Fuel (frozen, air intermixed)
• Injection pump
• Engine control computer
Throttle control a:Vehicle speed over 5km/h • Wiring harnesses and
system b:After engine is warmed Poor drivability connectors (throttle
15 [PA, E1] up, actual throttle opening control system)
deviates from target • Throttle opening sensor
throttle opening. • Engine control computer
c:Over 2 seconds
• Engine control computer
17 Internal IC system a:Battery voltage normal
b:Computer internal IC
89 abnormal
Spill-valve system a:Engine revolution over 500 • Wiring harnesses and
[SPV+, SPV-] rpm Engine stalling connectors (spill-valve
18 b:Spill-valve shorted inter- system)
nally • Spill-valve
• Engine control computer
Acceleration b:Accelerator sensor short b:Acceleration sensor • Wiring harnesses and
sensor system or open circuit short or open circuit Poor drivability connectors (acceleration
19 [VA, VAS, E2C] c:Over 0.05 seconds sensor system)
• Acceleration sensor
• Engine control computer
Acceleration b:Idle switch short or open • Wiring harnesses and
sensor system circuit. Poor drivability connectors (accelera-
19 (idle switch) c:Over 0.05 second tion sensor system)
[IDL, E2C] b:Large deviation between signals • Acceleration sensor
from two accelerator sensors. • Engine control computer

Acceleration sensor c:Over 0.05 second

a:Accelerator pedal fully • Wiring harnesses and
system (accelerator open Poor drivability connectors (accelerator
19 full-open switch) b:Over 5 second full-open switch system)
[PDL] c:Accelerator full-open •Acceleration full-open switch
switch open circuit • Engine control computer

- 58 -
 Diagnosis Contents n y
r
ito
e Diagnosis Item a o Main Symptom
d (a:Condition, b:Abnormality state, c:Abnormality period) p n i m
o (terminal symbol) m m e of Malfunction Inspection Area
C a llu
Normal Mode Check (Test) Mode L I M
Acceleration sensor a:Accelerator pedal fully Poor drivability • Wiring harnesses and
system (accelerator open connectors (accelerator
19 full-open switch) b:Accelerator full-open full-open switch system)
[PDL] switch open circuit • Acceleration full-open
switch
• Engine control computer
Water temperature b:Water temperature sensor b:Water temperature Poor cold •Wiring harnesses and
signal system circuit short or open circuit sensor circuit short or starting connectors (water
22 [THW, E2] c:Less than 0.5 second open circuit performance temperature sensor system)
c:Less than1 second /Poor drivability •Water temperature sensor
• Engine control computer
Intake air temperature b:Intake air temperature sensor b:Intake air temperature Poor drivability •Wiring harnesses and
sensor signal system circuit short or open circuit sensor circuit short or connectors (intake air
[THA, E2] c:Over 0.5 second open circuit temperature sensor system)
24 c:less than 1 second
N.A. •Intake air temperature
sensor
• Engine control computer
Correction system b:Correction circuit short or a:Correction circuit Poor drivability • Wiring harnesses and
[DATA, CLK, E2] open circuit short or open circuit connectors (correction
32 c:Less than 1 second N.A. system)
• Correction unit
• Engine control computer
Throttle control a:Battery voltage normal Vibration • Wiring harnesses and
system b:Idle stopper VSV circuit when connectors (throttle
[S/TH, E1] short or open circuit stopping control system)
33 c:Over 0.5 second engine • Throttle position sensor
• Piping
• Idle stopper VSV
Turbo pressure a:Over engine revolution 2400 a:Over engine revolution • Wiring harnesses and
sensor signal rpm, accelerator opening 2400 rpm, accelerator connectors (turbo
system more than half open opening more than half pressure sensor
[PIM, VC, E2] b:Intake manifold pressure open system)
35 abnormally low b:Intake manifold pressure • Turbo pressure sensor
c:Over 2 seconds abnormally low • Turbocharger
b:Intake manifold pressure b:Intake manifold • Actuator
abnormally high pressure abnormally • Engine control computer
c:Over 2 seconds highl
Fuel temperature b:Fuel temperature sensor b:Fuel temperature Poor drivability •Wiring harnesses and
sensor signal system circuit short or open circuit sensor circuit short or connectors (fuel
39 [THF, E2] c:Over 0.5 second open circuit c:Less than temperature sensor system)
1 second • Fuel temperature sensor
• Engine control computer
Vehicle speed a:After engine is warmed up, • Wiring harnesses and
42 sensor signal driving at engine revolution connectors (speed
system between 2000 to 4000 rpm sensor signal system)
[SP1] b:No input of speed sensor signal • Speed sensor
c:over 8 seconds • Engine control computer

Throttle system
sensor position b:Throttle position
circuit short sensor
or open Throttleshort
circuit circuit position sensor
or open Poor drivability •connectors
Wiring harnesses
(throttleand
47 [VLU, E2] c:Over 0.5 second circuit position sensor system)
• Throttle position sensor
• Engine control computer

- 59 -
Reference: Block Diagram (ex.3C-TE engine)

Turbo warning lamp

Power voltage Main relay

Glow relay
Water temp. sensor

Turbo pressure sensor Glow indicator lamp

Timing control valve

Crank position sensor

Solenoid spill valve

ROM

Acceleration sensor

Full-close accelerator
switch
ECU
Starter signal

Air-conditioner signal E-VRV(for EGR)

Throttle position sensor

VSV

Vehicle speed sensor VSV

Newtral switch E-VRV(for throttle)

Fuel temp. sensor

Intake air temp. sensor Tacho-meter signal

NE sensor Air-conditioner
signa l cut

PS0063E

- 60 -
Reference: Connecting Diagram

Main relay
Solenoid spill valve

Engine speed (Ne) sensor

NE sensor

Crankshaft
angle sensor
Glow plug relay
Crankshaft position sensor

Other ECU
Acceleration pedal S/W

MRE Sensor

ECU
Serial data

Neutral start S/W Timing control valve

y
a
l
e
r
r r
tre te
r
W
/ /W /W W
/
ta S S S S
o
S r r r p
m /W
e e e r S
v v v m e r
le le le a
l w e
tf fti fti p lo w
i o B ol
h h h t B
S S S
S O/D OFF lamp
p p p
m m m
a
l la la
r r r p
to ot ot m
a a a a
l
c
i c
i c
i
d d d p Check engine lamp
n
i n
i n
i o
t
fit tf
i
tf
i
S
h h h
S S S
Valve

A/C amp

Idle S/W
Acceleration sensor Solenoid

Fuel temp, sensor

Turbo Combination meter

pressure sensor Intalce air temp, sensor A/C amp, etc.

Water temp, sensor

ROM
Throttle position sensor

PS0064E

- 61 -
- 62 -
Chapter 2
ECD-V5

- 63 -
 Chapter 2 - Table of Contents
1. Gene ral Descr ipti ons ............................................................................... 65
1-1. Construction of ECD-V5 Pump .................................................................................... 66
1-2. Fuel Pressure-Feed and Injection ................................................................................ 67
2. System Confi gura tion .............................................................................. 68
2-1. System Components ................................................................................................... 69
3. Control Function ...................................................................................... 76
3-1. Fuel Injection Quantity Control ...................................................................................... 76
3-2. Fuel Injection Timing Control ........................................................................................ 79
3-3. Idle Speed Control ....................................................................................................... 82
3-4. EGR Control ................................................................................................................ 83
3-5. Other Controls ............................................................................................................. 84

- 64 -
1. General Descriptions
The ECD-V5 system detects the engine condition (engine speed, accelerator opening, intake air
pressure, cooling water temperature, etc.) through sensors, and controls the fuel injection quan-
tity, the fuel injection timing and all other factors with microcomputers to run the engine in the
optimum condition.
(1) Fuel injection quantity control
(2) Fuel injection timing control
(3) Idling speed control
(4) EGR control
(5) Glow plug control
In addition, the system also following functions;
(6) Fail-safe function
(7) Diagnosis function

The ECD-V5 system is divided into four major electric components: sensors; computers; elec-
tronic driving unit; and actuators.
Other signals Turbo charger
Immobilizer signal Main relay
CCO
Vehicle speed sensor SPV relay
Intercooler
Turbo pressure sensor A/C
Water temp. sensor
Intake air temp. sensor Glow system
(No.1 & No.2) EC U Crankshaft position
sensor
Acceleration sensor Engine
VSV
EGR lift sensor

VSV EGR
FCV
TCV
Atmospheric SPV
air pressure ED U
sensor

NE sensor

Fuel temp. sensor

ROM
Crankshaft position sensor

QT0266E

Sensors Detect the engine condition and the running state, and convert them into elec-
tric signals.
Actuators Operate in response to the electric signals from the computers.
Actuates the solenoid valve (SPV) using high amperage in accordance with the
EDU signals from the computer.
Computers Perform calculations based on electric signals from the sensors, and transmit
electric signals for optimization to the actuators.

- 65 -
1-1. Construction of ECD-V5 Pump
ECD-V5 pump is equipped with following electrical
parts.
(1) Actuators
a. Solenoid spill valve (SPV) for injection quantity
control
b. Timing control valve for injection timing control
c. Fuel cutoff valve (FCV) that cuts off the fuel injec-
tion.
(2) Sensors
a. Engine speed (NE) sensor QT0267E
b. Fuel temperature sensor
(3) ROM
New part on behalf of conventional correction resistors (θ & τ)
Connector (NE sensor)
Fuel temp. sensor
Solenoid spill valve
NE (engine speed) sensor

Roller ring

Pulser
Timing control valve
Cam plate
QT0268E

- 66 -
1-2. Fuel Pressure-Feed and Injection
The solenoid spill valve is located in the middle of the passage connecting the pump chamber and
the plunger pressure chamber.
The valve is a normal open type by the operation of the spool spring (return spring) in the solenoid
spill valve, and closes when its coil is energized.

(1) Suction Solenoid spill valve (open)

When the plunger moves down, the fuel enters the
pressure chamber.
Suction port : Open Pump chamber

•Distribution
•Solenoid port
spill valve : Closed
Open (deenergized) Suction port
Roller
Pressure chamber
Nozzle

Cam plate
Plunger Distribution port
QT0269E

(2) Injection Solenoid spill valve (closed)

Turning and rising, the plunger compresses and
feeds the fuel.
•Suction port : Closed
•Distribution port : Open
•Solenoid spill valve : Closed (energized) Roller

Cam plate

(3) End of Injection QT0270E

As soon as the solenoid spill valve is deenergized, it
opens. The pressurized fuel remaining in theplunger Solenoid spill valve (open)
chamber is compressed back to the pump cham-
ber, completing the pressure-feed cycle.
•Suction port : Closed
•Distribution port : Open
•Solenoid spill valve : Open (deenergized)
Roller
(4) Fuel Cutoff
While the injection of fuel is cut off, the current does
not flow to the solenoid spill valve, thus allowing the
spill port to remain open. Therefore, the fuel is not
pumped even when the plunger ascends. When the Cam plate
solenoid spill valve is closed, the fuel cutoff valve
(FCV) closes to cut off the fuel. QT0271E

- 67 -
2. System Configuration

.1
o
N
r
o
s
n
e
s
.
p dl
m o
te r if
e n
ir o a
a b
r rg m
e u a Re t
h v
k
a T c G la s
u
t Ev a
In h
x
r E
o
s
n
e
s
t
ifl
R
G
E
d r
l o
o s r
if n o
n e s
a s n
m . e
p s
e m n
V k e o
S . at t
r tii
V p In e s
y
t m2 t o
u et . a p
D ir o re W tf
me a rN u a
u s h
u c e s s
r
c u k o
s re k
n
a o ta e
n p r ra
Vs nI s o o
b s C
r n
u e
T s

U
U D
C E
E

n a d .
t e p
io
t a e m V
d p e C
ra n s t
l lil F
e l o e e p
e ti n
i u s e
c c
r c err g F d
i lv
o A n o a
s o E n e v
n e l
e C l lv o
s o a tr
n S v n
o o
ti c
. g
ra p n
i p
el m m
c
e M te ro mi u
p
l T
c O e s
A R u n e n
o
l Fs ti
a c
d je
e
pr In
to
ra
e
l
e
c
c
A QT0276E

- 68 -
2-1. System Components

U
C
E
h
c
ti
r w
o s
s 1
n
e le .
o
s d
I N
n r
o o
ti s
a
r n
e e
l U s
e D .
c E p
c m
A teri
a
e
k
ta
n
I
r
o
V s
S n
V e
V s
S y
t e
r u r
o V D u t
s y s u
n t s o
e
s
u
D re y
r . p a
o p o L
s m b
r s
n e u t
e t n
s r T e
n e n
o t .2 o
i a
it o p
s W N m
o r o
p o C
tf s
a n m
h e e
s
k
n .sp t
s
y
a
r r m S
o e
C) s tr
V n i
P e
s a
(S t e
e lif ta k
lv R n
a
v G I
lli E
p /
s e
v l
id ) v
a
o r V
n o C R
le s (T G
o n E
S e e
s lv
) a
E r v
l
(N o
s o
tr
d n n
e e o
e s c
p . g
s p n
e m i
n
i te m i
n
g
E le
u M
O T
F R

QT0278E

- 69 -
(1) Turbo Pressure Sensor Vacuum chamber
The turbo pressure sensor detects the intake air (built-in silicon chip)
pressure at the absolute pressure* and sends it to
the computer in the form of an intake air pressure
signal.
* Absolute pressure: A pressure in which vacuum is 0.

Boost pressure PR0068E

A crystal (silicon) is sealed inside the sensor. This
crystal has the characteristic of changing its electric
resistance when pressure is applied to it. The turbo ]
[V
pressure sensor is a type of semi-conductor pres- e
g
sure sensor that utilizes this characteristic. a tl
o
V
t
u
tp
u
O

Pressure [kgf/cm2]
Sensor Output Characteristics ES0359E

(2) Engine Speed (NE) Sensor Engine speed

The engine speed (NE) sensor is mounted opposite (NE) sensor
the gears of the pulser (gear) that is pressed on to Magnet
the driveshaft of the pump. Coil
The sensor contains a magnet and a coil. The mag- Roller ring
netic flux that passes through the coil varies with No gears
the rotation of the pulser, thus generating an alter- part
nating current voltage in the coil. The computer
counts the number of these pulses to detect the
engine speed. The pulser has 52 gears, with 3 gears
missing at 4 locations, enabling the pulser rotation PR0070E
angle to be detected at 11.25 ¡CA intervals.

360 °CA
Output Voltage (V) 11.25 °CA

Time
Signal Wave Form
PR0071E

- 70 -
(3) EDU (Electronic Driving Unit)
a. The ECD-V4 uses an EDU (CDI type high voltage driver) for high speed driving of the electro-
magnetic spill valve that works under high pressure. The introduction of high voltage and quick
charge systems using a DC/DC converter enables high speed driving of the spill valve that
controls the high fuel pressure. The precise control of the timing of injection of highly pressur-
ized and finely atomized fuel decreases the particulates* and exhaust gas emissions, and im-
proves maneuverability.
b. The ECU constantly monitors the EDU status and stops the engine if an EDU abnormality is
detected.

EMU signal wave form SPV+ electric current wave form

5
Time Time
0

High voltage generation circuit (DC-DC converter)

Battery SPV+
e
v l
a
v
ill
p s
EMU o id
n
Control le
ECU SPV− o
EDUF circuit S

EDU
QT0132E
*Particulates: fine particles of various materials (average size 0.1 υm) contained in higher quantities in diesel engine
exhaust than in gasoline engine exhaust.

•EDU operation
The battery voltage is boosted to a high voltage by a high voltage generation circuit (DC-DC con-
verter). The ECU controls the EDU according ot inputs from various sensors, via the EMU signal that
it outputs to the EMU terminal of the EDU.
The output
terminal of the
of the IJt which
EDU, signaldrives
causesthethe high voltage
solenoid (approx.
At this150
spill valve. V) the
time, to be output
EDUF from the
terminal SPV+
outputs the
injection confirmation signal.

- 71 -
(4) Accelerator Sensor Accelerator
On the ECD-V3, the sensor was mounted on the sensor
venturi to detect the accelerator opening. However,
on the ECD-V5, the accelerator opening is detected
at the accelerator pedal. Idle switch
In either case, the voltage of the output terminal
changes in accordance with the accelerator open-
ing.

QT0279E

Reception
Acceleration sensor circuit

VREF
5 ±0.3V

Amp TVO

E2

QT0280E

(5) Water Temperature Sensor

This sensor includes

temperature a thermistor
of the cooling and thermistor
water. The detects theuti-
lizes a semiconductor, the electrical resistance of Thermistor
which changes significantly with temperature. This
change in the electrical resistance is used for deter-
mining the cooling water temperature.

Structure PR0075E

30
20
) 10
Ω
(k 5
e 3
ul 2
a
V
ce 1
n 0.5
at 0.3
s
i 0.2
s
e
R0.1 -20 0 20 40 60 80 100 120
Water Temperature (¡C)
Characteristic B6202E

- 72 -
(6) Intake Air Temperature Sensors No.1, No.2
These sensors contain a built-in thermistor that has
the same characteristic as that of the water tem- Thermistor
perature sensor. They are mounted at 2 locations of
the intake manifold of the engine to detect the in-
take air temperature before and after the intake
manifold.

PR0077E

(7) Fuel Temperature Sensor

This sensor includes a thermistor having properties
similar to that of the thermistor included in the water Thermistor
temperature sensor.

PR0078E

(8) Solenoid Spill Valve (SPV) Plunger

Highly
solenoidpressure resistant
spill valve and highly responsive,
is a direct-acting the
solenoid valve Fuel return
that directly controls the injection volume. Spill ports
When the solenoid spill valve opens, the highly pres-
surized fuel in the plunger returns to the pumpcham-
ber, thus ending the injection of fuel.
*Refer to page 5 about SPV operation.

Spool valve Coil

QT0281E

(9) Fuel Cutoff Valve (FCV) Coil

It is a solenoid valve that cuts off the fuel injection
when the engine is stopped.
When the current is applied, its valve opens, allow-
ing the fuel to be drawn into the pressure chamber.

FCV valve QT0282E

- 73 -
(10) Computer (ECU)
ECU calculates injection quantity by using signals
from accelerator sensor, engine speed sensor and
other sensors.

PR0081E

(11) Crankshaft Position Sensor

This sensor is mounted in the front of the engine. A
protrusion that is provided on the crankshaft pulley
causes 1 pulse to be generated each time the en-
gine makes 1 revolution.
This pulse is then sent to the computer as the stan-
dard crankshaft angle signal.

Crankshaft
position sensor
QT0283E

360 ¡CA

Sh a p e Outpsuig
t nal
QT0284E, PR0089E

- 74 -
(12) Timing Control Valve (TCV) High-pressure Coil
The timing control valve is installed in the fuel injec- chamber
tion pump. According to the signals from the engine
control computer, the valve opens/closes the fuel Low-pressure
chamber
passage between the timer piston high-pressure
chamber side and low-pressure chamber side.
When the coil is energized, the spring is compressed Moving core
by the moving core, thus the fuel passage opens. Spring
One end of the timer control valve is connected to
Stator core
the main
engine relay,computer
control and the other endTCV.
terminal is connected to Structure PS0051E

Current that flows to the stator core is duty-controlled

by this terminal, and as the longer the ON time (time ON OFF

which engine control computer terminal TCV is t Average current: large

n
grounded), the longer is the length of thevalve open- re
r
ing time. u
C0
The timing control valve opening is controlled by the
ratio of the ON/OFF duration (duty ratio) of the cur- t Average current: small
rent supplied to the coil by the computer. n
e
rr
A longer ON duration produces a longer valve open- u
C0
ing duration. Time
Duty Control PR0095E

- 75 -
3. Control Function
3-1. Fuel Injection Quantity Control
(1) General Description of Fuel Injection Quantity Control
Correcting the basic fuel injection quantity calculated based on the engine condition (accelerator
opening, engine speed, etc.) in response to the water temperature, the fuel temperature, the intake
air temperature and pressure, etc., the engine control computer transmits the optimum output
signal for the engine condition to the solenoid spill valve of the ECD-V5 pump.
Especially, ROM on the pump instead of conventional correction resistors has correction data for
injection quantity and timing.

Engine speed (NE) sensor

Solenoid spill
Acceleration sensor ECU valve

Idling signal

Water temp. sensor ROM

Intake air temp. sensor No.1 & No.2

Fuel temp. sensor

Turbo pressure sensor

Vehicle speed sensor To nozzle

Starter signal
QT0285E

(2) Fuel Injection Quantity Control Method Solenoid spill valve (open)
The cam position of the cam plate determines the
fuel injection start timing.
Fuel injection stops after the solenoid spill valve is
deenergized (opens) and the pressurized fuel spills
out (is released) into the pump chamber. Roller
Consequently, the computer controls the fuel injec-
tion quantity by adjusting the fuel injection end tim-
ing.

Cam plate

QT0286E

- 76 -
(3) Basic Calculation of Fuel Injection Quantity Control
The fuel injectionquantity is determined based on two values (basic fuel injection quantity and
maximum fuel injection quantity).
a. Basic Fuel Injection Quantity
The basic fuel injection quantity is determined by the engine speed and the accelerator open-
ing.
b. Maximum Fuel Injection Quantity
The maximum fuel injection quantity is determined in response to the intake air into the engine
calculated based on the engine speed, the intake air pressure and temperature, etc.
Final fuel injection quantity is determined by the comparisonbetween the basic fuel injection quantity
and the maximum fuel injection quantity. The minimum value is adopted.

(4) Fuel Injection Quantity Control Flow

Acceleration sensor
Basic fuel injection quantity
Engine speed sensor
Basic maximum fuel
injection quantity
Select the Correction
Fuel temp. sensor less value with ROM EDU
Max. fuel injection
Water temp. sensor
SPV
Intake air temp. sensor No.2 Correction

ROM

QT0289E

a. Except Starting (Same as the previous ECD-V3)

Compares the basic fuel injection quantity and the
maximum injection, and the governor pattern of
the map for the less injection quantity is used for
determining the injection quantity. Low
y
itt
b. Starting (Same as the previous ECD-V3) n
a
Calculates the injection quantity in accordance u
q
with the engine speed and water temperature. l
e
fu
g
itn
r
a
t
S High

NE

QT0290E

- 77 -
(5) Various Types of Maximum Injection Quantity ECD-V3 Max.FuelInjection Quantity

a. Intake air pressure (PIM) compensation Governor Pattern

Based on the signals received from theturbo pres- Fuel

sure sensor, the intake air volume iscalculated in Injection

Quantity Vary by the required amount

order to correct the maximum injection quantity NE

towards enrichment during turbocharging. Max.PIM

compensation

b. Intake air temperature (THA) correction

THA THF Iearned ISC Iearned
correction correction correction

It is the same as ECD-V3. Choose small

Compensation
base transition
PIM
Max.injection
quantity
correction at cold
NE correction Deceleratic
correction
Max.compensation
period compensation

Intake air Water Fuel

PIM sensor NE sensor
temperature sensor temperature sensor temperature sensor

ECD-V5 Max.FuelInjection Quantity

Governor Pattern

Fuel
Injection
Quantity Vary by the required amount

NE

PIM THA THF Iearned ISC Iearned

compensation correction correction correction

Max.injection
quantity Deceleratic
NE correction
correction at cold correction

PIMsensor THAsensor THWsensor THFsensor NEsensor

PS0047E
(6) Correction with ROM Data
The new ECD-V5 is equipped with a ROM in place ECD-V3 Adjusting screw
of
V3the correction
system. resistor the
Accordingly, usedpoints
in theonprevious ECD-
which the in- (SPV)
Q
dividual pumps can be controlled have been in-
creased to realize a high level of precision. θ correction
Furthermore, the data in the ROM can be modified resistor
to make delicate injection quantity corrections eas-
ily, thus realizing a greater freedom of adjustment.

Np

ECD-V5
Q

Np
PS0048E

- 78 -
3-2. Fuel Injection Timing Control
(1) General Description of Fuel Injection Timing Control
The engine control computer (ECU) calculates the fuel injection timing, and transmits a signal to
the timing control valve (TCV) to maintain the optimum fuel injection timing.

Turbo pressure sensor ECU

Acceleration sensor
ROM
Engine speed sensor

SPV
Crankshaft position sensor

Water temp. sensor

Intake air temp. sensor No.1

Starter signal

Timer piston

Timing control valve

QT0292E

(2) Injection Timing Control Method

To control
to the timerthe injection
piston timing, the
is regulated by fuel pressure
varying of theoftimer
the length timelow-pressure chamber
in which the TCV that thus
is open, is applied
moving
the roller ring. When the length of time in which the TCV is open is long, the volume of fuel that
bypasses from the pump inner-pressure chamber to the timer low-pressure chamber increases,
causing the pressure in the timer low-pressure chamber to increase. As a result, the timer piston
moves in the retard direction. When the length of time in which the TCV is open is short, the timer
piston moves in the advance direction.

Roller ring

Pump inner-pressure chamber

Timer high-pressure chamber

Inlet
ECU
Orifice

Advance Delay Timing control valve

Timer piston

Timer low-pressure chamber

QT0293E

- 79 -
(3) Basic Calculation of Fuel Injection Timing Control
Correcting the basic fuel injection timing calculated from the engine conditions (accelerator
opening, engine speed, etc.) according to the water temperature, the intake air pressure, etc.,
the computer controls the following factors:
¥Optimum fuel injection timing according to fuel injection quantity (engine load) and engine
speed
¥Advance before engine warm-up
¥Advance at engine start-up
¥Advance at higher altitude where intake air density is lower
To provide accurate control, the actual fuel injection timing is computed from an input signal
issued by the TDC sensor and transmitted to the computer.(Refer to page 38,39.)
(4) Determine Target Injection Timing

ECU
Starter signal
Acceleration sensor
Basic target injection timing Target injection timing Timing control
Engine speed sensor valve
Intake air temp. sensor No.1
Comparison & Correction
Turbo pressure sensor Correction
Water temp.sensor
Actual injection timing
Crankshaft position sensor
ROM

QT0295E

(5) Vari ous Types of Injection Timing Correction

a. Intake air pressure correction advance )
A Engine speed decreases
The basics of calculating the amount of timing re °
(
C
u
advance correction based on the turbo pressure s
s
lu
e

sensor signal. re a
v
p
ir n
a oit
e c
k re
ta r
o
n I c

Low Intake air pressure High

(mmHg) QT0296E

- 80 -
b. Intake air temperature correction advance
The amount of timing advance correction based )
on the intake air temperature sensor signal. C
A
re (
°

tu e
a r c
e n
p av
md
te a
ir n
a io
t
e c
k e r
ta ro
In c

Cold Intake air temp. Hot

(°C)
QT0297E

c. Crankshaft angle correction

The NE pulse (camshaft angle signal) that is de-
tected by the rpm sensor is used for controlling
the injection timing. However, the correlation be- Injection
tween the camshaft angle signal and the injec- pulse
tion wave form deviates from one pump to an- Pump A
other, causing a deviation in the injection timing.
NE pulse
This deviation is corrected through the use of the
Pump B
correction data on the ROM that is attached to
the pump. Timing gap
PS0056E

- 81 -
3-3. Idle Speed Control

< S en sor> < C o m p u te r > <Actuator>

Engine speed sensor

Accelerati on sensor

Water temp. sensor

Vehicle speed sensor Idle speed
control Solenoid spill valve
Starter signal

Air conditioning signal

Neutral start signal

Power steering signal

QT0302E

(1)
The Feedback Control the desirable idling speed and the current idling speed (engine speed
computer compares
sensor signal). If any difference is found between them, the computer adjusts the injection quan-
tity to obtain the desirable idling speed.

(2) Warming Up Control

During warm-up, the computer sets a fast idling speed deemed optimum according to the cooling
water temperature.

(3) Expectation Control

To prevent a fluctuation in the idling speed due to a load fluctuation following an A/C switch opera-
tion, the computer changes the injection quantity by a preset amount immediately after the switch
operation but before the idling speed fluctuates.

(4) Idle Speed Stabilization Control

While theand
cylinder engine is running
corrects at the idling
it byadjusting speed, the
the injection computer
quantity detects
for each the speed
cylinder. fluctuation
This results at each
in reduced
vibrations at the idling speed.

- 82 -
3-4. EGR Control

Engine

Duty VSV

Engine speed
Accelerator
ECU Water temp.
Vacuum pump
EGR lift sensor

EGR valve

QT0303E

(1)
TheOutline
EGR system itself is almost identical to that of the previous system. Basi
cally, the ECU calculates
the target EGR valve lift value in accordance with the signals from the sensors, monitors the actual
amount of lift, and controls the 2 duty cycle VSVs to achieve the target lift value.

(2) EGR Valve

EGR lift sensor
When the vacuum in the diaphragm chamber of the
EGR valve increases, the EGR valve has the char- Controlled
acteristic to open. Consequently, the exhaust gases vacuum
flow from the exhaust manifold to the intake mani-
fold.
To intake
manifold

From exhaust
manifold
QT0304E

(3) Control Outline

a. The operation of the EGR is stopped at low and high temperatures.
b. The volume of EGR is reduced at high altitudes.

- 83 -
3-5. Other Controls
(1) Glow Plug Control
This control is intended to warm up the air in the o
r
IG
PIM
G-LA

combustion chamber when starting the engine at low s G-

n THW
e REL
temperatures and to make the glow plugs the source s
.
for igniting the fuel in order to ensure startability. p
m
te VG
r
e
t E2
a E1
W

a. Glow plug indicator illumination time control

When the ignition switch is turned ON, the glow QT0305E
plug indicator light illuminates only for the length
of time that is determined by the coolant water
temperature and the atmospheric pressure. Altitude (high places)
However, the indicator light turns OFF at the time )
c
the starter is turned ON. e
s
(
b. Glow plug relay control e
m
it
When the ignition switch is turned ON, super-glow
N
is implemented by applying current only for the O
length of time that is determined by the coolant
water temperature. Water temperature ( °C) 80
After the engine is started and the starter is turned Glow Plug Indicator Illumination Time Control
OFF, after-glow is implemented from that point. QT0306E

(2) Main Relay Control Main relay

Controls the systemÕs main powersupply relay. Does
not control+BB
terminal, the terminal,
power supply to the
and to the glow
computerÕs
plugs. IGSW
+B M-REL
EGRV

EGRA
+BB TCV

IGSW

SPV-REL
SPV relay

Main Relay Control

QT0307E

•Control time chart

a. When the IGSW is turned ON, the main relayturns ON
ON. IG switch OFF
b. When the IGSW is turned OFF, the main relay ON
turns OFF after 5 seconds have elapsed from the SPV relay
time SPD=0 is established. OFF
ON
Main relay 3 sec
(3) A/C Cut Control OFF
5 sec
When the ECU judges that vehicle acceleration has
reached a preset value, it signals the A/C ECU to Control Time Chart
cut the compressor OFF for 5 seconds. QT0308E

- 84 -
[Reference: Block Diagram(ex.RF-MDT engine)]

IG SW Main relay

Glow voltage Glow plug relay

Power supply Glow plug indicator lamp

Water temp. sensor TCV

Turbo pressure sensor EDU SPV

Crankshaft position sensor SPV relay

ROM Fan relay

Acceleration sensor

Idle switch

Starter signal ECU

A/C signal

FCV voltage Duty VSV

Vehicle speed sensor Duty VSV

Neutral switch FCV relay

Fuel temp. sensor

Intake air temp. sensor No.1

NE sensor Tachometer

Intake air temp. sensor No.2 A/C amplifier

EGR lift sensor

EDU fail signal

QT0277E

- 85 -
[Reference:External Wiring Diagram (ex. RF-MDT engine, A/T)

QT0310E

- 86 -
[Reference:EDU External Wiring Diagram (ex. RF-MDT engine)]

Battery High voltage SPV+

A generation
circuit D

EMU Control
B SPV
circuit
SPV–
EDUF
C E
GND (Case)
F

C A B D E F

QT0129E

- 87 -
- 88 -
Chapter 3
ECD-V4

- 89 -
 Chapter 3 - Table of Contents
1. Gene ral Descr ipti ons ................................................................................ 9 1
1-1. Injection Pump Mechanism (ex. 1HD-FTE engine) ....................................................... 92
2. System Configuration (ex. 1HD-FTE engine) ........................................ 95
2-1. System Components (on the vehicle) ........................................................................... 95
2-2. System Configuration (ex. 1HD-FTE engine)................................................................ 96
2-3. System Components ................................................................................................... 97
3. Control Functions ................................................................................... 10 2
3-1. List of Control Functions ............................................................................................ 102
3-2. Fuel Injection Quantity Control .................................................................................... 103
3-3. Fuel Injection Timing Control ...................................................................................... 105
3-4. Idle Speed Control ..................................................................................................... 108
3-5. Idle Speed Stabilization Control ................................................................................. 108
3-6. Other Control Items .................................................................................................... 109
3-7. EGR Control .............................................................................................................. 110

- 90 -
1. General Descriptions
The ECD-V4 is a new electronically-controlled distributor-type injection pump, based on the de-
sign of the ECD-V3 but with the incorporation of new mechanisms. The ECD-V4 offers improved
combustion along with highly precise andflexible control of theinjection quantity and timing. Major
changes regarding the new mechanisms are the inclusion of an inner cam mechanism, high-
response electromagnetic spill valve and EDU (Electronic Driving Unit), and compensation data
ROM.

ROM (Compensation data)

Engine
Fuel injection
pump Various data
EDU
·NE signal
·Fuel temperature
·Compensation values ECU

QT0089E

Improved combustion e
g
r
Increasing the fuelinjection pressure topromote the a
L
increased
in reducingatomization of fuel
gas emissions . has effectively resulted s
te
a
l
u Higher Injection
tirc Pressure
a
P
*

Low Injection High

Pressure QT0090E

REFERENCE ECD-V4 In-line pumps

The figure to the right compares the ECD-V4 with ) 120
a
P
other types of pumps in respect to the injection M
(
pressure. re
100

(The line in the graph indicates the injection pres- u

s
s
sures offered by existing pumps.) e
r 80
P
n
o ECD-V3
ti 60 (VE)
c
e
j
n
I
0
0 10 20 30 40
Pump Weight (kg) QT0091E

- 91 -
1-1. Injection Pump Mechanism (ex. 1HD-FTE engine)

Solenoid spill valve (SPV)

Engine speed (NE) sensor
Pulser
ROM
Feed pump
Rotor

Roller
Plunger
Cam ring (inner cam)
Timer piston
Timing control valve (TCV) QT0093E

(1) Inner Cam Mechanism

While the conventional ECD-V3 type pumps, like mechanical pumps, used a face cam mechanism
for fuel plunging, the ECD-V4 uses anewly developed inner cam mechanism to achieve the desired
injection pressure (approx. 130 MPa). The rollers revolve in the inner circumference of the cam, cre-
ating a reciprocal movement of the plunger and generating high press ure.
Inner Cam Mechanism Face Cam Mechanism

Cam
part

SPV Face cam

Suction Roller
Roller
SPV
Cam part Face cam
Roller Spill Roller
Suction
port

Rotor
Cam part Delivery port
* QT0095E, QT0096E

- 92 -
•Advantages of the Inner Cam
In the face cam mechanism, the rollers slip as shown
on the right. Thus, the face cam mechanism is unable
to withstand high pressure. Meanwhile, the inner cam
mechanism can withstand high pressure because the Cam
rollers only roll, without creating slippage. Slipping

(2) High Response Solenoid Spill Valve andEDU

To improve the spill action, the solenoid has been
Roller Roller
changed to a high-response type.
Cam ring Roller
Combined
valve yieldsfurther with
a higher the use
speed of an EDU, the spill
driveability. Roller

Face cam
ECD-V4 ECD-V3

QT0097E

ECD-V3
Adjusting screw (SPV)
(3) Compensation Data ROM
Q
Like the ECD-V3 (ROM), the ECD-V4 performs in-
jection quantity/timing control using the compensation correction
values stored in ROM. (The figure to theright shows θ
resister
an example of the injection quantity mapping data frag-
mented through the use of the compensation values
stored in the ROM.)

Np

ECD-V4
Q

Np
PS0048E

- 93 -
(4) Hydraulic Circuit
a. The engine turns the injection pump drive shaft that drives the built-in feed pump.The feed pump
sucks the fuel from the fuel tank and feeds it to the feed gallery inside the injection pump. (Feed
gallery pressure: 1.5 to 2.0 MPa)
b. The spill valve opens (SPV: OFF), feeding the fuel into the fuel delivery system (rotor chamber).
c. The spill valve closes (SPV: ON). The fuel contained in the rotorhamber
c is pressurized by the inner
cam and plunger, which are driven by the drive shaft. The fuel is then plunged through the high
pressure line from the delivery valveto the nozzle, thereby producing afuel spray.
d. When the spill valve opens (SPV: OFF) and the pressure in the rotor chamber decreases, the
delivery valve closes and injection ends.
A cycle with the above four steps (“a” through “d”) is repeated for each cylinder in the order of the
injection sequence.
Accumulator (absorbs pulsation caused by SPV operations)
SPV
SPV a

Pump room
b Feed gallery
Rotor
d Delivery
valve
Feed pump
c
Plunger Fuel delivery system Plunger

QT0094E
REFERENCE
To decrease the dead volume of fuel passage in the fuel delivery system, the spill valve is offset
from
need the fuelintake
for an passage and the
port such fuel
as in theisconventional
forcibly sucked through
design the spill decreases
and thereby valve. Thisthe
eliminates the
dead volume.

(5) Cam Ring Mechanism and Function

a. Fuel sucking and pressurizing
Cam ring

Roller

Plunger

Sucking Pressurizing
QT0099E

- 94 -
b. Injection timing advance and delay

Direction of rotor rotation

Delay (Front of vehicle)

Advance

Timer piston

Injection Timing Advance and Delay Maximum Delay

QT0100E

2. System Configuration (ex. 1HD-FTE engine)

2-1. System Components (on the vehicle)
Accelerator sensor
EGR valve
Turbo pressure sensor
Throttle valve close switch
VSV (Ambient switch)
Intake temp. sensor

Intake heater

Intake shutter

VSV (EGR) ECU

EDU
E-VRV (EGR)
Crankshaft position sensor

*The enclosed component names indicate

Water temp. sensor
DENSO components.
QT0092E

- 95 -
2-2. System Configuration (ex. 1HD-FTE engine)

r m
ir n
a
.
k .
at m
nI t m
t r
r
V t
S
V a n
W

lv V
S
v V
R
G h
E it
V
S
r r V
u
V l
r
u r n V
R
T E
vl
a
v
tlt
r
h
T

UD
E M

U
C
E

QT0101E

- 96 -
2-3. System Components
(1) Solenoid Spill Valve (high response type)
The spill valve is installed in the fuel passage between
the feed gallery and pump room. According to sig-
nals from EDU, the spill valve controls the sucking of
fuel into the high pressure system, the injection cutoff,
and the split injection.

Spiral coil
mechanism

Valve

Rotor chamber
Feed gallery

QT0104E

(2) Engine Speed (NE) Sensor

The NE sensor is mounted on the cam ring and de-
tects the engine
mounted speed
on the drive through the pulser that is
shaft. Cam ring
As with the NE sensor for the ECD-V3 , the NE sensor Pulser (13×6)
for the ECD-V4 is positioned in such a way as to pro-
vide independence from theinjection timing. The pe- No pulser
riphery of the 72 gears pulsar has six gaps with three Drive shaft
gears missing at each gap, allowing for detection of a
cam angle of *3.75 degrees. *360÷{(13 x 6)+(3x 6)} Timer piston
QT0106E

Signal Wave Form Single revolution of injection pump drive shaft

720 °CA
Single revolution of crank shaft
360 °CA

3
← 13 →↔

QT0108E

- 97 -
(3) EDU (Electronic Driving Unit)
a.The ECD-V4 uses an EDU (CDI type high voltage driver) for high speed driving of the electromag-
netic spill valve that works under high pressure. The introduction of highvoltage and quick charge
systems using a DC/DC converter enables high speed driving of the spill valve that controls the
high fuel pressure.
b.The ECU constantly monitors the EDU status and stops the engine if an EDU abnormality is de-
tected.
IJt signal wave form SPV+ voltage wave form
Approx. 150
5 Time Time
0 0
High voltage generation circuit (DC-DC converter)

Battery SPV+ c
ti
e e
n
g
a lv
va
m lli
IJt
Control ro
tc p
s
ECU IJf circuit SPV− e
l
E

QT0132E
*Particulates: fine particles of various materials (average size 0.1 υm) contained in higher quantities in diesel engine
exhaust than in gasoline engine exhaust.
•EDU operation
The battery voltage is boosted to a high voltage by a high voltage generation circuit (DC-DC
converter). The ECU controls the EDU by outputting signal to the EDU’s IJt terminal.
The output of the IJt signal causes the high voltage (approx. 150 V) to be output from the SPV+
terminal of the EDU, which drives the electromagnetic spill valve. At this time, the IJf terminal
outputs the injection confirmation signal.

- 98 -
(4) Accelerator Sensor
As with the ECD-V3 (ROM), the ECD-V4 uses a hall
device to detect the throttle valve opening at the ac- Throttle valve
celerator pedal. The accelerator sensor output volt- close switch
age changes with the throttle valve opening. At the
same time, the idle switch position (ON/OFF) is refer-
enced in order to find out whether the engine is idling
or not. Accelerator sensor
The control accuracy is improved bythe combination
of two detection systems:
• Idle switch and throttle valveclose switch
• VA and VAS QT0110E

5.0
) e Vcc
V
( 4.0
g
n
e a
r
g t
tal 3.0 u
p
t
o u
v o
t l VA
u 2.0
a
tp m
r
u 1.0 o VAS
O N
IDL
0
-10 0 10 20 30 40 50 60 70
Sensor
8090
rotation
Service range angle θ (degrees) E

Output Characteristics QT0133E QT0111E

(5) Turbo Pressure Sensor

This sensor detects the intake pressure (absolute Vacuum chamber
pressure), converts the pressure level into a signal,
and sends it to the computer as the intake pressure
signal. This semiconductor type pressure sensorin-
cludes a crystal (silicon), the electrical resistance of
which changes with the pressure it receives. This
change in the electrical resistance is used for deter-
mining the intake pressure.
*Absolute pressure: pneumatic pressure measured in reference
to that in a vacuum, which is indicated as zero.

Intake pressure
(Turbo)
PR0068E

- 99 -
(6) Water Temperature Sensor
This sensor includes a thermistor and detects the tem-
perature of the cooling water. The thermistor utilizes a Thermistor
semiconductor, the electrical resistance of which
changes significantly with temperature. This change
in the electrical resistance is used for determining the
cooling water temperature.

Structure PR0075E

) 30
Ω 20
(k 10
e
lu 5
a 3
V 2
c e
n 1
ta
s is 0.5
e 0.3
R0.2
0.1
-20 0 20 40 60 80 100 120
Water Temperature (°C)
Characteristic B6202E

(7) Intake Temperature Sensor

This sensor includes a thermistor having properties
similar to that of the thermistor included in the water
temperature sensor. This sensor is installed in the in- Thermistor
take pipe of the engine and detects the intake tem-
perature.

PR0077E

(8) Fuel Temperature Sensor

This sensor includes a thermistor having properties
similar to that of the thermistor included in the water Thermistor
temperature sensor. This sensor is installed on the
injection pump and detects the fuel temperature.

PR0078E

- 100 -
(9) Crankshaft Position Sensor
As conventionally done, the crankshaft position sen-
sor is installed on the engine block and generates a
single pulse per singleengine revolution, as it detects
a projection on the crankshaft. The pulses generated Crankshaft position
by the crankshaft position sensor are called crankshaft sensor
position reference signals.
To ECU

Projection
Cylinder block QT0107E

(10) Timing Control Valve (TCV)

The timing control valve is installed in the fuel injection pu
mp. According to the signals from the engin
e
control computer, the valve opens/closes the fuel passage between the timer piston high-pressure
chamber side and low-pressure chamber side.
When the coil is energized, the spring is compressed by the moving core, thus the fuel passage
opens.
One end of the timer control valve is connected to the main relay, and the other end is connected to
engine control computer terminal TCV. Current that flows to the stator core is duty-controlled by this
terminal, and as the longer the ON time (time which engine control computer terminal TCV is grounded),
the longer is the length of the valveopening time.
The timing control valve opening is controlled by the ratio of the ON/OFF duration (duty ratio) of the
current supplied to the coil by thecomputer. A longer ON duration produces a longer valve opening
duration.
ON OFF
Coil t
n
e
Moving core ru Average current: large
C
Low-pressure 0
chamber
t
n
re
r Average current: small
u
C
High-pressure Spring 0
chamber Stator core Time
QT0131E, PR0095E

- 101 -
3. Control Functions
3-1. List of Control Functions
Control Item Function
Regulates the injection quantity to the quantity deemed optimum ac-
Fuel injection quantity
cording to the engine conditions determined by inputs from various
control
sensors.
M/T vehicle: Controls the engine torquewhen the transmission isshifted
Engine torque into 1st or reverse gear.
control A/T vehicle: Controls the engine torque when demanded by the ECT-
ECU, typically during a gear shift.
Fuel injection timing Adjusts the injection timing to the timing deemed optimum according
control to the engine conditions determined by inputs from various sensors.
Determines the desirable idling speed according to the engine condi-
Idle speed control tions, and adjusts the fuel injection quantity accordingly to achieve the
desirable idling speed.
Idle speed Detects the engine speed fluctuation at each cylinder, and eliminates
stabilization fluctuations by correcting the injection quantity for each cylinder.
Heater idle-up If the heater switch at the driver’s seat is ON, the idling speed will
control increase while the vehicle is at a stop.
Closes the intake shutter installed upstream on the intake pipe No. 1
Intake cutoff control when the engine stops in order to reduce vibrations and noise.
Determines the duration of intake heater activation (pre-heating be-
Intake heater control fore ignition and after-heating after ignition) according to the engine
cooling water temperature.
In extremely cold weather, performs a split injection (two injections
Split injection control per a single plunge) to facilitate starting and reduce white smoke and
noise.
Water temperature data The ECU outputs the cooling water temperature data to the air condi-
output tioner amplifier for air conditioner (compressor) control.
Cuts off the air conditioner during acceleration to improve drivability.
A/C cutoff control (power With the cold weather specifications, controls the viscous heater as
heater cutoff control) well.
Under certain travel conditions, circulates a part of the exhaust gas
EGR control back to the intake manifold to slow down combustion and decrease
NOx emissions.
When an abnormality has occurred in the engine control computer
Diagnosis
signal system, turns the Check Engine lamp ON.
When an abnormality has occurred in conjunction with a sensor sig-
Fail safe nal, continues the control activities by using the default values stored
in the engine control computer or stops the engine.

- 102 -
3-2. Fuel Injection Quantity Control

Engine speed (NE) sensor

EDU

Accelerator sensor
Turbo pressure sensor
Intake air temp. sensor
ECU Water temp. sensor
Starter signal
1st gear position switch*

ROM Vehicle speed sensor

Fuel temp. sensor

QT0105E

* : With an M/T vehicle, the 1st gear switch activates the power control to protect the drive system during high load
operation.
In general the ECD-V4 determines the injection quantity from the basic and maximum injection
quantities, as done by the ECD-V3 (ROM). With the ECD-V4, however, the spill valve EDU has
been added to the system.
ECU
Accelerator sensor
Basic fuel injection quantity
Engine speed sensor
Fuel temp. sensor Basic maximum fuel
injection quantity
Select the Correction
Water temp. sensor less value with ROM EDU
Max. Fuel Injection
Intake air temp. sensor
SPV
Turbo pressure sensor Correction
ROM
QT0109E

(1) Split Injection Control

When the engine needs to be started in extr
emely cold weather (when the water or fuel temperature is
-10°C or less), the ECD-V4 performs a split injection to decrease thestarting time and white smoke.

- 103 -
A single plunger operation normally produces a single
injection (SPV: OFF → ON → OFF). With the split
injection, however, the ECU and EDU produce drive
signals in such a way that two injections can be pro-
duced by a single plunger operation (SPV: OFF → SPV drive current
ON → OFF → ON → OFF).
(2) Maximum Injection Quantity Compensations SPV operation
Open Close
•Intake pressure compensation (higher intake pres-
sure → higher injection quantity) Cam lift
•Intake temperature compensation (higher intake tem-
perature → lower injection quantity)
•Fuel temperature compensation (higher fuel tempera-
ture → higher injection quantity)
•Water temperature compensation (low cooling wa-
ter temperature → higher injection quantity) Nozzle lift
•Engine speed compensation control
•ECT control (A/T vehicle) QT0112E
•Power control (M/T vehicle)
•ROM (individual compensation data)

REFERENCE
1. Injection quantity determination method
The injection quantity is changed by controlling the
injection end timing, namely, the electromagnetic
spill valve opening timing. Engine speed (NE)
2. Solenoid valve opening timing sensor
The engine speed sensor is used to determine Pulser Cam ring
the solenoid valveopening timing. The cam angle
that corresponds to the cam lift is determined as
follows:
a. The cam lift is determined by the rotation angle
of the rotor which rotates in one unit with the
pulser, and this rotation is in turn detected by the Drive shaft Rotor
engine speed sensor. Roller
b. The rotation angle of the rotor is detected by QT0114E
the rotation angle of the pulser, which can be
determined from the engine speed sensor sig-
nal output (single pulse per the cam angle of Injection Start Injection End
3.75 degrees).
Cam lift
c. The computer uses the engine speed sensor Reference pulse
signal output to determine the electromagnetic NE sensor
spill valve opening timing (injection end timing)
by the number of gears and the duration of time Open Close Open
Solenoid spill valve
from detection of the pulser gap.
Injection
Cylinder A
Cam angle
Injection End Control QT0115E

- 104 -
•Example (1HD-FTE engine)

11 12 0 12 3 4 56 7 8 9 10 11 12 0

Injection End

Close (ON)
SPV
Open (OFF)

Plunger Lift

Injection

QT0116E

3-3. Fuel Injection Timing Control

Engine speed (NE) sensor

Accelerator sensor
Turbo pressure sensor
Intake air temp. sensor
ECU Water temp. sensor
Starter signal
1st gear position switch
Crank shaft position sensor

ROM
Fuel temp. sensor
Timing control valve (TCV)

QT0113E

- 105 -
As with the ECD-V3 (ROM), the ECD-V4 determines the duty ratio by comparing the target and
actual injection timings.

Accelerator sensor
Basic target injection timing Taget injection timing
Timing control
Engine speed sensor valve

Turbo pressure sensor Correction Comparison & Correction

Water temp. sensor

Crankshaft position sensor Actualinjection timing

ROM

PS0053E

(1) Injection Timing Compensations

* Intake pressure compensation (low intake pressure -> timing advance)
* Water temperature compensation (low cooling water temperature -> timing advance)
* ROM data compensation (crank angle compensation etc.)

(2) Timing Control Valve Drive Method

Engine speed NE pulse synchronization control (ex-
cept at an engine stall)
(3) Feedback Control θ

The feedback control is performed over thetime-phase

difference (θ in the figure) between the actual com- Actual compression
TDC
pression TDC and the ni jection start point. No signal, θ 1 Engine
however, directly shows the actual compression TDC TDC signal
and injection wave form.
The actual injection timing, therefore, is determined
Ne pulse
by the following method. Pump
•Determining the actual injection timing: Injection wave form
a. On the engine side, the compression TDC position
has a relationship with the TDC signal fromthe crank PR0092E
position sensor.
b. On the pump side, the actual injection timing
has a relationship with the NE pulses from the en-
gine speed sensor.
c. The actual injection timing, therefore, is determined
by calculating the phase differenceθ 1 between the
TDC signal and NE pulses.
•Feedback control:
The TCV duty ratio is controlled so that the actual in-
jection timing matches the target injection timing.

- 106 -
 REFERENCE Engine speed
Relationship between injection timing and quantity: sensor
(mounted on
The injection timing is controlled by changing the Cam ring cam ring)
position of the timer piston and the cam ring con- Pulser(13×6)
nected with it (the position determines the injec-
tion start timing). Since the injection start timing No pulser
advances with the injection end timing, the injec-
Drive shaft
tion quantity is not affected by changes in the in-
jection start timing. The engine speed sensor is
installed to, and therefore moves with, the cam Timer piston

ring.relationship
Even whenbetween
the cam ring position is changed, QT0106E
the the cam lift and NE
pulses (a relationship that affects the injection
quantity control) remains the same.
•Example (1HD-FTE engine)

(TDC)
Actual crank angle signal
t
11 12 0 123 4 567 8 9 10 11 12 0

QT0117E

- 107 -
3-4. Idle Speed Control

Engine speed (NE) sensor

EDU

Accelerator sensor
Water temp. sensor
Vehicle speed sensor
ECU Starter signal
Neutral start switch signal
Air conditioning signal
Power heater switch signal

ROM 1st gear position switch

Fuel temp. sensor

QT0118E
*ex. 1HD-FTE engine
(1) Feedback Control Engine speed
The computer compares the desirable idling speed Condition
M/T A/T
and
nal).the current
If any speedsi (by
difference engine
found speed
between sensor
them, sig- No-load idling
the com- 600 600
puter adjusts the injection quantity to obtain the desir- A/C ON 825 825(N), 750(D)
able idling speed. Power heater ON 1200 1200

(2) Warming Up Control

During warm-up, the computer sets a fast idling speed deemed optimum according to the cooling
water temperature.
(3) Expectation Control
To prevent a fluctuation in the idling speeddue to a load fluctuation following an A/C switch operation,
the computer changes the injection quantity by a preset amount immediately after the switch opera-
tion but before the idling speed fluctuates.
(4) Power Heater Idle Up Control
If the power heater switch is turned ON and the vehicle is at halt, the ECU controls the spill valve to
increase the idling speed.

3-5. Idle Speed Stabilization Control

While the engine is running at the idling speed, the computer detects the speed fluctuation at each
cylinder and corrects it by adjusting theinjection quantity for each cylinder. This results in reduced
vibrations at the idling speed.

- 108 -
3-6. Other Control Items
(1) Intake Cutoff Control
The intake cutoff control opens and closes the intake shutter installed on the intake pipe.
The purpose of the intake cutoff system isto cut off the intake and reducevibrations when the engine
is being shut down.

When the ignition switch is turned OFF, the

Engine started : valve fully open
vacuum pressure is led to the actuator and
Engine shutdown : valve fully closed
the valve is closed.
After engine shutdown: valve fully open

Vacuum Pressure

Ambient

Ignition Signal QT0119E

(2) A/C Cut Control

When the ECU judges that vehicle acceleration hasreached a preset value, itsignals the A/C ECU to
cut the compressor OFF for 3 seconds.
(3) Air Conditioner Control (30 °C or below)
The A/C ECU uses the cooling water temperature A
output to control theair conditioner. The duration “A”
in the figure to the right changes with the water tem- →
perature as shown in the table below: e
g (75 °C)
a
tl
·ex. 1HD-FTE engine o A
V
Water Temperature Duration A (ms)
30 °C or below 82
30-90 °C Proportional (90 °C or above)
A
90 °C or above 410
(4) Power Heater Control (ex. 1HD-FTE engine)
When the power heater switch at the driver’s seat is 420 ms 420ms
turned ON, the idling speed is increased to 1200 rpm.
•Control enabled when: Time → QT0120E
a. Engine speed is equal to or below the preset value;
and
b. Cooling water temperature is equal to or below the Engine Speed Control
ON
preset value.
•Control disabled when: 2000 2500
OFF
a. Engine being started; or (rpm)

b. A/C ON; or (vehicle speed less than 30km/h and Water Temperature Control
c. Accelerating ON
throttle opening 45% or more for 5 sec. or more).
OFF
69 74
QT0121E, QT0122E

- 109 -
(5) Intake Heater Control
During a cold start, the intake heater is activated (90 sec. max.) to incre
ase the intake temperature.
•Control enabled when:
a. Ignition switch ON; and
b. Cooling water temperature less than 40 °C.

Intake heater relay

Indicator lamp
e
c
Input interface r a
rf Starter
circuit te
r n
te Fuse
e i
t
v u ti
/D on tp
u ir
u
c Ignition switch
Ac O c

Water temperature sensor

CPU
Memory

Input interface
Battery (12V)
circuit

Constant-voltage power supply

QT0123E

3-7. EGR Control

EDU
Fuel temp. sensor Intercooler
Engine speed (NE) sensor SPV VSV

Intake shutter
Intake heater
Turbo Intake air
pressure temp. sensor
sensor EGR valve

VSV

ROM
TCV
E-VRV VSV

Water temp.
sensor

Crankshaft
position sensor

Accelerator sensor
ECU Throttle valve close switch Vaccum pump
1st gear position
switch or
Neutral start switch
signal
QT0124E

- 110 -
(1) Control Specifications
The EGR system used with the ECD-V4 isnot very different from conventional EGRsystems. The
basic control scheme is as follows: the ECU performs a duty control overthe electrical current through
the E-VRV according to inputs from various sensors, thereby changing the vacuum pressure in the
diaphragm chamber of the EGR valve andthus the EGR valve opening, until the exhaust gas recircu-
lation amount appropriate to the engine condition is obtained.

Wiring
Accelerator
sensor Vacuum piping

Engine speed
(NE) sensor
ECU E-VRV VSV
Water temp.
sensor

Turbo pressure Intake air temp.

sensor sensor EGR valve

QT0125E

(2) Operation
The ECU performs a duty control over the electrical
current through the E-VRV according to inputs from
various sensors, thereby changing the vacuum pres-
EGR valve
sure in the
thus the EGRdiaphragm chamber
valve opening, of theEGR
until valve
exhaust gasand
re-
circulation amount appropriate to the engine condi-
tion is obtained. EGR gas
Depending on the engine speedand throttle opening, To intake manifold
the ECU may switch the intake pipe to the intake sen-
sor to sense the atmospheric pressure instead of the Intake shutter
boost pressure for obtaining the exhaust gas recircu- EGR valve
lation amount appropriate to the traveling conditions.
•EGR disabled when: E-VRV VSV

a. Cooling water temperature 60 °C or below, or 96

¡C or above; or
b. Under high load condition (approx. 70% or more of
the full load and engine running at 4400 rpm or
above); or
c. Decelerating (EGR is active, however, when the
engine is idling); or
d. Engine speed low (600 rpm or less)
e. STA ON QT0126E
f. IG OFF

- 111 -
[Reference:Block Diagram (ex. 1HD-FTE engine)]

Power supply
Power supply voltage circuit
TCV
Intake air temp. sensor
A/D converter
Water temp. sensor E-VRV (EGR)
ti
Fuel temp. sensor c
u VSV (for cut-off)
ir
c
Turbo pressure sensor e
c
fa r
VSV (intake shutter)
Accelerator sensor te
tin
u
Engine speed (NE) sensor p
Intake heater relay
n
I
Crankshaft position sensor
EDU VSV (ambient switch)
CPU
ti Glow indicator lamp
u
c
ri
Throttle valve close sensor c
c e
Check engine lamp
Vehicle speed sensor fa
r
te
in
Air conditioner amplifier t Air conditioning cut-off signal
u
tp
it u
Idle up switch (Heater) u
c O
ir Main relay
c
Power heater amplifier e Memory V
c EDU relay
far
P
S
Starter signal te
n
i
t
Neutral start switch *
1
u
p
In
ROM Water temp. data
Failure detection
1st gear position switch * 2
circuit EDU
Ignition switch Engine speed signal

TC terminal

*1
Viscous heater amplifier Transmission ECU
*1: A/T vehicle only
*2: M/T vehicle only
QT0102E

- 112 -
[Reference:External Wiring Diagram (ex. 1HD-FTE engine)

+B
Main relay MREL

SPVD
(70½)
BATT SPVF

E1

EDU
(Engine GND)

NE+
SVR

NE-
MPU
Spill valve relay
MPU (90½)
TDC+

TDC-

TC EGR
E-VRV
12½ (at 20 ¡C)

PDL Intake heater relay

Accelerator pedal switch 4.72½ (at 12 V)

IREL

Speed sensor SP1

(inside meter console)

Viscous heater amplifier VCH

S/TH Vacuum switching valve

(35½)
10½
TR AC1
PA
Vacuum switching valve
A/C AMP (35½)

SIL ECU serial data

IGSW

TCV
NSW Timing control valve
IG2
1st gear switch (10½)

FSW
ST2
Power steering switch
EGRC
h h Vacuum switching valve
PS
v (35½)
w Idle up switch
T

n HSW

N
E01

h STA
E02

Circuit Diagram 1/2

QT0127E

- 113 -
 +B +B +B

h
tic h
c
h
c
w ti it
s w w
r s s +B (inside meter console)
e e e
v k k
le ra ra
Cruise indicator lamp
tf 1.4W at 12V
i B B
h
S PI

p STP
Check engine lamp
m
a
l 1.4W at 12V
r p ST1
to a
m W
a l
ic p
d
in to Bulb (1.4W)
fti S
h GIND
S

Cruise control switch

CCS

l e
e t m Cruise main switch
c e u
n s
a S e CMS
C R THWO
A/C amplifier
(E2)
ACT

(E2)

Accelerator sensor

VCC VCT Viscous heater amplifier

VA

VAS
EFI +
IDL
ECT ECU
EFI -
E2C

Turbo pressure sensor

VC
Fuel temp. sensor Meter,
THF TAC A/C amplifier,
etc.
PIM
Intake air temp. sensor
THA
Water temp. sensor
THW

E2 CLK
ROM

ECT +
ECT ECU
ECT -

DATA

Circuit Diagram 2/2

QT0128E

- 114 -
[Reference:EDU External Wiring Diagram (ex. 1HD-FTE engine) ]

Battery High voltage SPV+

2 generation circuit 4

from ECU IJt

3 Control circuit SPV
SPVD
SPV−
to ECU IJf 5
SPVF
1
GND (Case)
6

1 2 3 4 5 6

QT0129E

- 115 -