Con.

GradFck Fcd Ecm

C16/20 16 9.07 29
C20/25
C25/30
20 11.33
25 14.17
30
31
ISOLATED FO
C30/37 30 17.00 33
C35/45 35 19.83 34
C40/50 40 22.67 35
C45/55 45 25.50 36
C50/60 50 28.33 37
ISOLATED FOUNDATION DESIGN ES EN

Cover to reinforcement
(For structural class of S-4 )
Select Exposure class XC2/XC3
Cmin dur= 25
Cmin bond= 16
Cmin used= 25
Concrete cover (C.)= 60 d'=

Etabs output
Story Joint label load case /combo Fx Fy
Base 23 Comb1 - Ultimate -1.15 -2.78
Base 33 Comb1 - Service -0.88 -2.08

Material Data
Concrete data Reinforcement data
fcu(Mpa)= C25/30 fyk(Mpa)= 400
Fck= 25
fcd(Mpa)= 14.17 fyd(Mpa)= 347.826086957
fctm(Mpa)= 2.5650 gms = 1.15
gmc = 1.5 Es(Gpa)= 200
Ecm(Gpa)= 31
cover (mm)= 60 main barø(mm) 16

Footing Proportioning
Factor of safety (FS) Footing geometry
FS= 1.38279667221 L= 3.1
sall= 280 kpa B= 3.1
sult= 387.18306822 kpa L/B= 1
Ecentricity at service load dvrc= 697
ex= 0.00034254942 dvrc min= 656
ey= 0.00055618798 d (wide beam) 697
 the stress at the four corners of the footing
smax= 200.536571448 since maximum stress < allowable stress, the footing dimensi
smin= 199.840119499 ok!

since both conditions are satisfied, take:-

L= 3.1
B= 3.1
Depth determination
Ecentricity at ultimate load
ex= 0.00032928988
ey= 0.00052024794
the stress at the four corners of the footing
smin= 276.367929912 kPa
sint-1= 276.720788157
sint-2= 276.925413716
smax= 277.278271961
save= 276.82310094

wide beam shear

Critical section for shear is at distance d from the face of supports.
depth for Vrdc
The design shear for at section Y-Y is:
V y-y= 474.558 D= 765
V x-x= 474.558 dvrc=
C rd,c = 0.120 dvrc, min
rmin= 0.002
K= 1.536
V rd,c = 640.795 kN difference 166.2
Vsd= 474.558 kN status good depth
Check for K= 1.536 ok!
depth for Vrdc min
The design shear for at section Y-Y is:
V y-y= 509.742058065 D= 724
V x-x= 509.742058065
C rd,c = 0.12
rmin= 0.0017
K= 1.55215763037
V rd,c min= 688.188352907 kN difference 178.4
Vsd= 509.742058065 kN status good depth
Check for K= 1.55215763037 ok!
 The depth of the footing for wide beam shear is 770
d= 702

Punching shear
Critical section for shear is at distance 2d from the face of column.
check punching shear at critical perimetre (column face)
Ved,red= 2577.22306972 kN
With q=220 22 0.38397243543875 cot q 2.475
n= 0.54 Z= 631.8 acw=
Vrd,max= 3693.21860841
punching shear at the face of the column is SAFE
check punching shear at critical perimetre ( 1.5d distance from the column face)
Ved,red= 708.159 Note:- if the critical section lies outside the footing d
C rd,c = 0.120 no verification for punching shear is required!!!
rmin= 0.002
K= 1.534 Lpunching 2.706
U0= 10.624 Wpunching 2.606
V rd,c 2209.067
V rd,c min= 2479.131
punching shear at the face of the column is SAFE
check punching shear at critical perimetre ( 2d distance from the column face)
No verification is required
take D=770
Note:- if the critical section lies outside the footing d
Ved,red= -460.541 no verification for punching shear is required!!!
C rd,c = 0.120
rmin= 0.002 Lpunching 3.408
K= 1.534 Wpunching 3.308
U0= 13.432
V rd,c 2792.94
V rd,c min= 3134.384
punching shear at the face of the column is SAFE

The depth of footing required for both wide beam and punching shear is=

Reinforcement Calculation
Parallel to X-Direction Parallel to Y-Dir
Msdx= 670.43 kN-m Msdy=
Msdx= 216.27 kN-m/m Msdy=
msd= 0.031 msd=
Kz= 0.981 Kz=
As,calculated= 903.32 mm2 As,calculated=
2
As,min= 1170.39 mm As,min=
 As,max= 28080 mm2 As,max=
As,provided= 1170.39 mm2
As,provided=
Spacing= 170 mm Spacing=
Provide ∅16 C/C170 Provide ∅16 C/C170
GN ES EN 2015

68

ut
Fz Mx My Mz
2660.27 1.384 -0.876 0.078
1923.81 1.07 -0.659 0.054

column geometry
3.5 H= 0.6
2.5 B= 0.5
1.4
stress, the footing dimension is accepted

3.1m

500

3.1m
B
600
y-axis

X-axis

upports.

644968.68958
-803107.008
column.
2.475086853

tan q 0.404
1 U0= 2.2

olumn face)
on lies outside the footing dimension,
ing shear is required!!!

lumn face)

on lies outside the footing dimension,

ing shear is required!!!

770 d= 702

Kz,x
Parallel to Y-Direction msd Kz
725.14 kN-m 0.04 0.976
233.92 kN-m/m 0.031 0.981
0.03350558 0.05 0.971
0.97924721
978.28959 mm2 Kz,y
1170.39304 mm 2
msd Kz
 28080 mm2 0.04 0.976
1170.39304 mm 2
0.034 0.979
170 mm 0.05 0.971
Provide ∅16 C/C170