Scribd
Upload
48 views4 pages

(A) A+B A+B (B) A+AB B (C) (A+B) (A+C) A+BC (D) (A+1) (A+B) A

1. According to Boolean algebra, repeated addition of the same term A results in nA. 2. An AND gate is enabled when its enable input is at logic 0. 3. I/O devices provide means for a computer to communicate with the user or other computers.

Uploaded by

sai mohan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
48 views4 pages

(A) A+B A+B (B) A+AB B (C) (A+B) (A+C) A+BC (D) (A+1) (A+B) A

1. According to Boolean algebra, repeated addition of the same term A results in nA. 2. An AND gate is enabled when its enable input is at logic 0. 3. I/O devices provide means for a computer to communicate with the user or other computers.

Uploaded by

sai mohan
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

1.

According to Boolean algebra, A+A+A+A+A………+A is


(a) n A (b)0 (c) 1 (d) A
2. Which of the following Boolean algebraic expressions is incorrect?
(a)A+B=A+B (b) A+AB=B (c) (A+B)(A+C)=A+BC (d) (A+1)(A+B)=A

3. A gate is enabled when its enable input is at logic 0. The gate is


(a)NOR (b) AND (c) NAND (d) None of these

4. Determine the value of base x if : (211)x= (152)8


(a) 2 (b) 10 (c) 8 (d) 7
5. The devices that provide the means for a computer to communicate with the user or other computers are referred to
as:
a) CPU b) I/O c) ALU d) None of the above

6. Division of (131B6C3) base 16 by (lA2F) base 16 yeilds –


a) 1AD b) DAD c) BAD d) 9AD

7. The software used to drive microprocessor-based systems is called:

a) Assemble language b) firm language c)Machine language d) BASIC interpreter instructions

8. How many buses are connected as part of the 8085A microprocessor?

a) 2 b) 3 c) 4 d)5

9. What is mean by ALU


a) Arithmetic logic upgrade b) Arithmetic logic unsigned
c) Arithmetic local unsigned d) Arithmetic logic unit
10. How many control lines are present in analog to digital converter in addition to reference voltage?
a) Three
b) Two
c) One
d) None of the mentioned
11. ADC Means______________ converter
a) Analog to data b) Analog to digital
c)Analog to Discrete d) Analog to Different
12. How many clock pulses do a successive approximation converter requires for obtaining a
digital output.
a) Twelve
b) Six
c) Eight
d) None of the mentioned
13. Which type of ADC follow the conversion technique of changing the analog input signal to
a linear function of frequency?
a) Direct type ADC
b) Integrating type ADC
c) Both integrating and direct type ADC
d) None of the mentioned
14. In an open loop control system
(a) Output is independent of control input
(b) Output is dependent on control input
(c) Only system parameters have effect on the control output
(d) None of the above

15. A control system in which the control action is somehow dependent on the output is known
as
(a) Closed loop system
(b) Semiclosed loop system
(c) Open system
(d) None of the above
16. The initial response when tune output is not equal to input is called
(a) Transient response
(b) Error response
(c) Dynamic response
(d) Either of the above

17. ___ increases the steady state accuracy.


(a) Integrator
(b) Differentiator
(c) Phase lead compensator
(d) Phase lag compensator

18. Mass, in force-voltage analogy, is analogous to


(a) charge
(b) current
(c) inductance
(d) resistance

19. In force-voltage analogy, velocity is analogous to


(a) current
(b) charge
(c) inductance
(d) capacitance

20. The viscous friction co-efficient, in force-voltage analogy, is analogous to


(a) charge
(b) resistance
(c) reciprocal of inductance
(d) reciprocal of conductance
(e) none of the above

21. The fastest A/D converter type is(a) counter type A/D converter (b)Successive approximation type
A/D converter (c) Dual slope integrated type A/D converter (d) Flash type A/D converter

22. The output of an AND gate with three inputs, A, B, and C, is HIGH when ________.
A. A = 1, B = 1, C = 0

B. A = 0, B = 0, C = 0

C. A = 1, B = 1, C = 1
D. A = 1, B = 0, C = 1
23.
When used with an IC, what does the term "QUAD" indicate?
A. 2 circuits
B. 4 circuits

C. 6 circuits

D. 8 circuits
24. The NOR logic gate is the same as the operation of the ________ gate with an inverter connected to
the output.
A. OR

B. AND

C. NAND

D. none of the above

25. The logic expression for a NOR gate is ________.


A.

B.

C.

D.

26. Which of the following is not a basic Boolean operation?


A. OR

B. NOT

C. AND

D. FOR
27. The ________ ensures that only one IC is active at a time to avoid a bus conflict caused by two ICs
writing different data to the same bus.
A. control bus

B. control instructions

C. address decoder

D. CPU
28. I/O mapped systems identify their input/output devices by giving them a(n) ________.
A. 8-bit port number

B. 16-bit port number

C. 8-bit buffer number

D. 8-bit instruction

29. The 8085A is a(n):


A. 16-bit parallel CPU

B. 8-bit serial CPU

C. 8-bit parallel CPU

D. none of the above

30. Which bus is a bidirectional bus?


A. address bus

B. data bus

C. address bus and data bus

D. none of the above

31. Which of the following are the three basic sections of a microprocessor unit?
A. operand, register, and arithmetic/logic unit (ALU)

B. control and timing, register, and arithmetic/logic unit (ALU)

C. control and timing, register, and memory

D. arithmetic/logic unit (ALU), memory, and input/output

You might also like