• Installation: Direct panel mounting; mounting bracket, one each for upper and ● Cable Speci cations and

● Cable Speci cations and Recommended Cables ' 5HOD :LULQ

lower mounting
RZ WR RQQHFW :LUHV
3XUSRVH 1DPH DQG 0DQXIDFWXUHU
• Panel cutout dimensions (mm): UT35A, UT32A
Power supply, relay contact outputs 600 V Grade heat-resistant PVC insulated wires, JIS C
UT35A: 92+0.8/0 (W) × 92+0.8/0 (H) 3317(HIV), 0.9 to 2.0 mm
External DC power supply
:LULQ ZRUN PXVW EH FDUULHG RXW E D SHUVRQ ZLWK EDVLF HOHFWULFDO Relay
UT32A: 45+0.6/0 (W) × 92+0.8/0 (H) NQRZOHG H DQG SUDFWLFDO H SHULHQFH HP F SH Shielded compensating lead wires, JIS C 1610
Mounting attitude: Up to 30 degrees above the horizontal. No downward titling allowed. For thermocouple input (PV input and remote input with direct
H VXUH WR WXUQ 2)) WKH SRZHU VXSSO WR WKH FRQWUROOHU EHIRUH input), shielded compensating lead wire of cross-sectional area R
• Wiring: M3 screw terminal with square washer (for signal wiring and power wiring) WARNING ZLULQ WR DYRLG DQ HOHFWULF VKRFN 8VH D WHVWHU RU VLPLODU GHYLFH WR less than or equal to 0.75 mm is recommended. If the cross-
HQVXUH WKDW QR SRZHU LV EHLQ VXSSOLHG WR D FDEOH WR EH FRQQHFWHG sectional area is wide, the reference junction compensation
error may be large. Diode
■ Power Supply Speci cations and Isolation )RU WKH ZLULQ FDEOH WKH WHPSHUDWXUH UDWLQ LV RU PRUH
RTD Shielded wires (three/four conductors), UL2482 (Hitachi Cable) (Mount it directly
V D VDIHW PHDVXUH DOZD V LQVWDOO D FLUFXLW EUHDNHU DQ ,( UT’s contact Relay
• Power supply: Other signals (other than contact input/output) 6 H H H to the relay coil
FRPSDWLEOH SURGXFW 9 RU 9 LQ DQ HDVLO (Use one with a relay coil rating terminal (socket).)
Rated voltage: 100-240 V AC (+10%/-15%), 50/60 Hz Other signals (contact input/output) Unshielded wires
DFFHVVLEOH ORFDWLRQ QHDU WKH LQVWUXPHQW 0RUHRYHU SURYLGH less than the UT’s contact rating.)
24 V AC/DC (+10%/-15%) (for /DC option) RS-485 communication 6 H H H
LQGLFDWLRQ WKDW WKH VZLWFK LV D GHYLFH IRU WXUQLQ RII WKH SRZHU WR
• Power consumption: UT35A: 18 VA (DC:9 VA, AC: 14 VA if /DC option is speci ed) WKH LQVWUXPHQW Ethernet communication 100 BASE-TX (CAT-5)/10 BASE-T
UT32A: 15 VA (DC:7 VA, AC: 11 VA if /DC option is speci ed) ,QVWDOO WKH SRZHU FDEOH NHHSLQ D GLVWDQFH RI PRUH WKDQ FP PROFIBUS-DP communication Dedicated cable for PROFIBUS-DP (Shielded two-wires) 5HOD :LULQ
• Data backup: Nonvolatile memory IURP RWKHU VL QDO ZLUHV DeviceNet communication Dedicated cable for DeviceNet (Shielded ve-wires)
• Power holdup time: 20 ms (for 100 V AC drive) CC-Link communication Dedicated cable for CC-Link (Shielded three-wires) External AC power supply
7KH SRZHU FDEOH LV UHTXLUHG WR PHHW WKH ,( VWDQGDUGV FRQFHUQHG RU UT35A, UT32A
• Withstanding voltage WKH UHTXLUHPHQWV RI WKH DUHD LQ ZKLFK WKH LQVWUXPHQW LV EHLQ LQVWDOOHG PROFIBUS-DP/CC-Link Connector (wiring side) (Part number: A1987JT)
Between primary terminals and secondary terminals: 2300 V AC for 1 minute (UL, CSA) :LULQ VKRXOG EH LQVWDOOHG WR FRQIRUP WR 1( 1DWLRQDO (OHFWULFDO DeviceNet Connector (wiring side) (Part number: L4502BW)
Between primary terminals and secondary terminals: 3000 V AC for 1 minute (CE) RGH 16, 1)3 RU WKH ZLULQ FRQVWUXFWLRQ VWDQGDUGV LQ Recommended tightening torque: 0.5 to 0.6 N·m
Between primary terminals: 1500 V AC for 1 minute FRXQWULHV RU UH LRQV ZKHUH ZLULQ ZLOO EH LQVWDOOHG R
Between secondary terminals: 500 V AC for 1 minute 6LQFH WKH LQVXODWLRQ SURYLGHG WR HDFK UHOD RXWSXW WHUPLQDO LV
(Primary terminals: Power* and relay output terminals; Secondary terminals: )XQFWLRQDO LQVXODWLRQ SURYLGH 5HLQIRUFHG LQVXODWLRQ WR WKH
Analog I/O signal terminals, contact input terminals, communication terminals H WHUQDO RI WKH GHYLFH DV QHFHVVDU 5HIHU WR WKH GUDZLQ EHORZ UT’s contact Relay CR filter
and functional grounding terminals.)
This product (Use one with a relay coil (Mount it directly
*: Power terminals for 24V AC/DC models are the secondary terminals. This product
A safety A safety rating less than the UT’s to the relay coil
• Insulation resistance: Between power supply terminals and a grounding terminal A safety
voltage circuit voltage circuit voltage circuit contact rating.) terminal (socket).)
20 MΩ or more at 500 V DC
Functional Functional
• Isolation speci cations Reinforced insulation
insulation insulation
PV (universal ) input terminals A hazardous A hazardous 7UDQVLVWRU 2XWSXW :LULQ
A safety
voltage circuit voltage circuit voltage circuit
Control, retransmission (analog) output terminals UT
(not isolated between the analog output terminals) Reinforced insulation DO
Valve position (feedback) input terminals 7HUPLQDO :LULQ 'LD UDPV Load
Control relay (contact point c/contact point a x 2) output terminals This product COM
A hazardous A hazardous + –
Alarm-1 relay (contact point a) output terminals Internal Power voltage circuit voltage circuit 'R QRW XVH DQ XQDVVL QHG WHUPLQDO DV WKH UHOD WHUPLQDO power

Alarm-2 relay (contact point a) output terminals circuits supply Functional 'R QRW XVH D 9 SRZHU VXSSO IRU WKH 9 '
insulation Reinforced insulation PRGHO RWKHUZLVH WKH LQVWUXPHQW ZLOO PDOIXQFWLRQ
Alarm-3 relay (contact point a) output terminals A hazardous A hazardous CAUTION
voltage circuit voltage circuit
Position proportional relay output terminals
Reinforced insulation
■ UT35A
Contact input terminals (all)
RS-485 communication terminals (2 ports)
(Equipped
Control output OUT PV input PV as standard) Retransmission output RET (Equipped as standard)
24 V DC loop power supply terminals (Suffix code: Type1=-0) Factory default: PV input
Relay contact output TC input RTD input Retransmission output 15 V DC loop power supply Can be used for 15 V DC loop
:KHQ FRQQHFWLQ WZR RU PRUH FULPS RQ WHUPLQDO OX V WR WKH type is undefined. power supply when not used for
Contact output (transistor) terminals Terminal wiring differs in Heating/cooling Default: PV
NC 101 A 201 retransmission retransmission output.
VLQ OH WHUPLQDO EORFN EHQG WKH FULPS RQ WHUPLQDO OX V EHIRUH control and Position proportional control.
+ 202 + 205 + 205
Ethernet communication terminal Refer to the terminals of Position 4-20 mA DC or 14.5-18.0 V DC
WL KWHQLQ WKH VFUHZ NO 102 b 202 0-20 mA DC (Max. 21 mA DC)
proportional control output and - 203 - 206 - 206
CAUTION 1RWH WKDW WKH ZLULQ RI WZR RU PRUH FULPS RQ WHUPLQDO OX V WR WKH Heating/cooling control output below.
PROFIBUS-DP/DeviceNet/CC-Link communication terminals COM 103 B 203 Load resistance 600 Ω or less
VLQ OH KL K YROWD H WHUPLQDO RI WKH SRZHU VXSSO DQG UHOD HWF Factory default: Control output is relay. Default: 4-20 mA DC
Current transformer input terminals Contact rating: 250 V AC, 3 A Current (mA) input Voltage (mV, V) input
GRHV QRW FRPSO ZLWK WKH VDIHW VWDQGDUG 30 V DC, 3 A (resistance load)
Cooling-side control output RET/OUT2
The circuits divided by lines are insulated mutually. - 203 + 202 (Suffix code: Type 1=-2)
Current/voltage pulse output
Can not be used for retransmission output or
Heating/cooling control output + 204 - 203 15 V DC loop power supply when
3URYLGH HOHFWULFLW IURP D VLQ OH SKDVH SRZHU VXSSO ,I WKH + 205
0-20 mA DC, current/voltage pulse output is used.
■ Environmental Conditions Heating/cooling relay contact output (Suffix code: Type 1=-2) 4-20 mA DC,
SRZHU LV QRLV LQVWDOO DQ LVRODWLRQ WUDQVIRUPHU RQ WKH SULPDU Voltage pulse (12V) Can be used for retransmission output or 15 V
Cooling NO E4-terminal area E1-terminal area - 206 DC loop power supply when control output is
VLGH DQG XVH D OLQH ILOWHU RQ WKH VHFRQGDU VLGH :KHQ PHDVXUHV OUT2 -side 101
101 501 401 301 201 not used.
1RUPDO 2SHUDWLQ RQGLWLRQV CAUTION D DLQVW QRLVH DUH WDNHQ GR QRW LQVWDOO WKH SULPDU DQG VHFRQGDU Heating NO Current output range can be changed.
OUT -side 102 -112 -512 -412 -306 -212
• Ambient temperature: -10 to 50°C (side-by-side mounting: -10 to 40 °C) SRZHU FDEOHV FORVH WR HDFK RWKHU
401
COM 103 101 501 301 201
If the CC-Link option is speci ed, 0 to 50 °C for UT35A; 0 to 40 °C for UT32A. ,I WKHUH LV D ULVN RI H WHUQDO OL KWQLQ VXU HV XVH D OL KWQLQ
Contact rating: 240 V AC, 3 A 102 502 302 202
(side-by-side mounting: 0 to 40 °C for UT35A and UT32A with CC-Link option) DUUHVWHU HWF
30 V DC, 3 A (resistance load) Control output OUT (Suffix code: Type1=-0, -1 or -2)
• Ambient humidity: 20 to 90% RH (no condensation allowed) )RU 7 LQSXW XVH VKLHOGHG FRPSHQVDWLQ OHDG ZLUHV IRU ZLULQ 103 503 303 203
Current/voltage pulse output Retransmission output 15 V DC loop power supply
• Magnetic eld: 400 A/m or less )RU 57' LQSXW XVH VKLHOGHG ZLUHV WKDW KDYH ORZ FRQGXFWRU 104 504 304 204
Default: Undefined
UHVLVWDQFH DQG FDXVH QR VL QLILFDQW GLIIHUHQFHV LQ UHVLVWDQFH Wiring direction
• Continuous vibration at 5 to 9 Hz: Half amplitude of 1.5 mm or less, 1oct/min for 90 105 505 305 205 + 207
0-20 mA DC, + 207 + 207
EHWZHHQ WKH WKUHH ZLUHV 4-20 mA DC, 0-20 mA DC, 14.5-18.0 V DC
minutes each in the three axis directions 106 506 306 206 Voltage pulse (12 V) 4-20 mA DC (Max. 21 mA DC)
6LQFH WKH FRQWURO RXWSXW UHOD KDV D OLIH VSDQ UHVLVWDQFH ORDG RI - 208 - 208 - 208
Continuous vibration at 9 to 150 Hz: 4.9 m/s or less, 1oct/min for 90 minutes each 107 507 407 207
WLPHV XVH WKH DX LOLDU UHOD WR SHUIRUP 21 2)) FRQWURO Default: 4-20 mA DC
in the three axis directions 108 508 408 208
7KH XVH RI LQGXFWDQFH / ORDGV VXFK DV DX LOLDU UHOD V PRWRUV (Equipped Can be used for retransmission output or 15 V DC loop power supply when
• Short-period vibration: 14.7 m/s , 15 seconds or less Contact output ALM as standard) 109 509 409 current/voltage pulse output is not used for control output.
DQG VROHQRLG YDOYHV FDXVHV PDOIXQFWLRQ RU UHOD IDLOXUH DOZD V Current output range can be changed.
• Shock: 98 m/s or less, 11 ms External contact output (relay)
LQVHUW D 5 ILOWHU IRU XVH ZLWK DOWHUQDWLQ FXUUHQW RU D GLRGH IRU 110 510 410 210 In Position proportional type, can be used for retransmission output or 15 V
• Altitude: 2000 m or less above sea level Alarm-3 output UT DC loop power supply.
XVH ZLWK GLUHFW FXUUHQW DV D VSDUN UHPRYDO VXU H VXSSUHVVLRQ (PV high limit) 104 111 511 411 211
• Warm-up time: 30 minutes or more after the power is turned on AL3
FLUFXLW LQWR WKH OLQH LQ SDUDOOHO ZLWK WKH ORDG 112 512 412 212
• Startup time: Within 10 seconds Common 105
IWHU FRPSOHWLQ WKH ZLULQ WKH WHUPLQDO FRYHU LV UHFRPPHQGHG Contact input DI (Equipped as standard)
*: The LCD (a liquid crystal display) is used for a display portion of this product. Alarm-2 output
WR XVH IRU WKH LQVWUXPHQW ( PV low limit) 106 External contact input
The LCD has a characteristic that the display action becomes late at the low AL2 No-voltage
E3-terminal area UT Transistor UT
temperature. However, the control function is not affected. Common 107 contact contact +5V
STOP when DI2=ON DI2
Alarm-1 output 210 DI2 210
RUN when DI2=OFF +5V
7UDQVSRUWDWLRQ DQG 6WRUD H RQGLWLRQV (PV high limit) 108
AUTO when DI1=ON DI1
● Recommended Crimp-on Terminal Lugs AL1 211 DI1 211
• Temperature: -25 to 70ºC 109 MAN when DI1=OFF
Common COM
• Temperature change rate: 20ºC/h or less (ød ) Position proportional control output VALV Common 212 COM 212
Relay contact rating: 240 V AC, 1 A
• Humidity: 5 to 95% RH (no condensation allowed) 30 V DC, 1 A (resistance load) Relay contact output Feedback input (Suffix code: Type1=-1) Contact rating: 12 V DC, 10 mA or more
HIGH 100% Function can be assigned to the terminals with no function.
(A) (direct) 507 510
(IIHFWV RI 2SHUDWLQ RQGLWLRQV 5.5 3.3
LOW
• Effect of ambient temperature: Power supply (reverse) 508 511

Voltage or TC input: ±1 µV/ºC or ±0.01% of F.S./ºC, whichever is larger (F) 100-240 V AC power supply 24 V AC/DC power supply COM 509 Heater break alarm HBA (Option code /HA)
0% 512
Current input: ±0.01% of F.S./ºC N N Heater current detection input
110 - 110 Contact rating: 250 V AC, 3A Resistance: 100 Ω to 2.5 kΩ External contact output (transistor)
30 V DC, 3 A UT
RTD input: ±0.05ºC/ºC (ambient temperature) or less Recommended tightening torque: 0.6 N·m L L (resistance load) 510
111 + 111 Feedback input Heater break alarm-1 HAL1 507
Analog output: ±0.02% of F.S./ºC or less Applicable wire size: Power supply wiring 1.25 mm P H output CT1
Current (mA)
input + 510 Heater break alarm-2
511
• Effect of power supply voltage uctuation 112 112 HAL2 508 CT2
SSOLFDEOH WHUPLQDO OX SSOLFDEOH ZLUH VL H PP : (φ d) ) output
Analog input: ±0.05% of F.S. or less Allowable range: 511 512
0.25 to 1.65 (22 to 16) (24 V AC/DC power supply: Option code /DC) Common COM 509 COM
100-240VAC (+10%/-15%)
Analog output: ±0.05% of F.S. or less (free voltage) - 512
50/60 Hz shared Transistor contact rating: 24 V DC, 50 mA
(Each within rated voltage range) When feedback input is current
,0 3 ' (1 SD H
■ UT35A (Continued from page 3) ■ UT32A
Control output OUT PV input PV (Equipped
as standard) Retransmission output RET (Equipped as standard)
301-306 501-506 (Suffix code: Type1=-0) Factory default: TC input RTD input
E4-terminal area E1-terminal area E1-Terminal Area E4-Terminal Area Relay contact output Retransmission output 15 V DC loop power supply Can be used for 15 V DC loop
Terminal wiring differs in Heating/cooling PV input type is power supply when not used for
Default:
NC 101 undefined. A 201 PV retransmission retransmission output.
control and Position proportional control.
+ 202 + 205 + 205
101 501 401 301 201 Refer to the terminals of Position 4-20 mA DC or 14.5-18.0 V DC
Contact input DI (Suffix code: Type 2=2) Contact output NO 102 b 202
DO (Suffix code: Type 2=2) proportional control output and 0-20 mA DC (Max. 21 mA DC)
-112 -512 -412 -306 -212 - 203 - 206 - 206
External contact input External contact output Heating/cooling control output below.
COM 103 B 203 Load resistance 600 Ω or less
101 501 401 301 201 Factory default: Control output is relay. Default: 4-20 mA DC
No-voltage UT UT UT
contact Transistor contact Contact rating: 250 V AC, 3 A
COM Factory default: No function DO45 501 Current (mA) input Voltage (mV, V) input
102 502 302 202 301 30 V DC, 3 A (resistance load)
Common 301 COM
+5V Cooling-side control output RET/OUT2
103 503 303 203 DI11 Factory default: No function DO44 502 - 203 + 202
Factory default: No function 302 DI11 302 Current/voltage pulse output (Suffix code: Type 1=-2)
+5V
104 504 304 204 DI12 Factory default: No function DO43 503 - 203 Can not be used for retransmission output or 15 V
Factory default: No function 303 DI12 303 + 204
+5V + 205 DC loop power suppy when current/voltage pulse
DI13 0-20 mA DC,
105 505 305 205 Factory default: No function DO42 504 4-20 mA DC, output is used for control output.
Factory default: No function 304 DI13 304
+5V Heating/cooling control output Voltage pulse (12 V) Can be used for retransmission output or 15 V DC
106 506 306 206 DI14 E1-terminal area - 206 loop power suppy when control output is not used.
Factory default: No function 305 DI14 305 Factory default: No function DO41 505 101 301 201
+5V Heating/cooling relay contact output (Suffix code: Type 1=-2) Current output range can be changed.
107 507 407 207 DI15 Cooling NO -112 -312 -212
Factory default: No function 306 DI15 306 Common COM 506 OUT2 -side 101
108 508 408 208 101 301 201
Contact rating: 12 V DC, 10 mA or more Function can be assigned to the Transistor contact rating: 24 V DC, 50 mA
Heating NO
102
OUT -side 102 302 202
109 509 409 terminals with no function. Function can be assigned
COM 103
110 510 410 210 to the terminals with no 103 303 203 Control output OUT (Suffix code: Type1=-0, -1 or -2)
function. Contact rating: 240 V AC, 3 A 104 304 204 Current/voltage pulse output Retransmission output 15 V DC loop power supply
111 511 411 211 30 V DC, 3 A (resistance load) Wiring direction
Contact input / Contact output DI/DO (Suffix code: Type 2=1) Default: Undefined
105 305 205 + 207
112 512 412 212 0-20 mA DC, + 207 + 207
External contact input 0-20 mA DC, 14.5-18.0 V DC
106 306 206 4-20 mA DC,
No-voltage Voltage pulse (12 V) 4-20 mA DC (Max. 21 mA DC)
UT Transistor contact UT 24 V DC loop power supply - 208 - 208
contact 107 307 207 - 208
COM
Common 301 COM 301 24 V DC loop power supply Default: 4-20 mA DC
E3-terminal area +5V LPS24 108 308 208
DI11 (Option code /LP) Can be used for retransmission output or 15 V DC loop power suppy when
Factory default: No function 302 DI11 302 (Equipped
+5V + 505 Contact output ALM 109 309 current/voltage pulse output is not used for control output.
DI12 21.6-28.0 V DC as standard)
Factory default: No function 303 DI12 303 (Max. 30 mA DC) Current output range can be changed.
- 506 External contact output (relay) 110 310 210
In Position proportional type, can be used for retransmission output or 15 V DC
Contact rating: 12 V DC, 10 mA or more Alarm-3 output UT 111 311 211 loop power supply.
(PV high limit) 104
External contact output Function can be AL3 312
112 212
assigned to the Common 105
UT terminals with no
Factory default: No function DO12 304
function. Alarm-2 output Contact input DI (Equipped as standard)
(PV low limit)
106
AL2 External contact input
Factory default: No function DO11 305 Common 107 No-voltage UT
contact UT Transistor
contact +5V
Alarm-1 output STOP when DI2=ON
DI2
Common COM 306 108 210 DI2 210
(PV high limit) RUN when DI2=OFF +5V
AL1 DI1
Transistor contact rating: 24 V DC, 50 mA 109 AUTO when DI1=ON 211 DI1 211
Common Position proportional control output VALV MAN when DI1=OFF
COM
Relay contact rating: 240 V AC, 1 A Relay contact output Feedback input (Suffix code: Type1=-1)
Common 212 COM 212
30 V DC, 1 A (resistance load)
HIGH 100%
(direct) 101 310
Contact rating: 12 V DC, 10 mA or more
LOW 311 Function can be assigned to the terminals with no function.
Power supply (reverse) 102
100-240 V AC power supply 24 V AC/DC power supply (24 V AC/DC power supply: COM 103 0% 312
Option code /DC) Heater break alarm HBA (Option code /HA)
N N Contact rating: 240 V AC, 3A Resistance: 100 Ω to 2.5 kΩ
110 - 110
30 V DC, 3 A External contact output (transistor) Heater current detection input
L L (resistance load) Feedback input
111 + 111 UT
Current (mA) Heater break alarm-1 310
HAL1 307
input + 310 output CT1
112 112
Heater break alarm-2
311
output
HAL2 308 CT2
Allowable range: 311
100-240VAC (+10%/-15%) 312
(free voltage) Common COM 309 COM
- 312
50/60 Hz shared
When feedback input is current Transistor contact rating: 24 V DC, 50 mA

401-412 E3-Terminal Area 301-306 E1-Terminal Area

RS-485 communication RS485 Ethernet communication (with gateway function) PROFIBUS-DP communication (with Modbus master)
RS-485 (Suffix code: VP RS-485 communication RS485 24 V DC loop power supply CC-Link communication (with Modbus master)
10BASE-T/100BASE-TX ETHR PROF
Type 3=1) 1 Data 390Ω RS-485 24 V DC loop power supply
SDB(+) 407
RJ45 connector (Suffix code: Type 3=2) CHK line (Suffix code: Type 3=4) (Suffix code: LPS24 If the UT is located at the end of a
CC-L
2 RxD/TxD-P FG: Flame ground 301
RDY Type 2=1) segment for the CC-Link (Suffix code: Type 3=3)
3 Data 220Ω If the UT is located at the end SDB(+) 301 (Suffix code: Type 2=0 and
SDA(-) 408 ERR line communication wiring,terminating
Upper side LED (baud rate) RxD/TxD-N of a segment for the + 305 SLD: Shield 302
4 21.6-28.0 V DC option code /LP) resistors are separately needed.
SG 409 Color Amber PROFIBUS
390Ω SDA(-) 302 (Max. 30 mA DC) These are to be prepared by
5 - 306 DG: TX/RX signal ground 303
DGNDcommunication wiring,
Lit 100M bps users. (110 Ω: 1 pc.)
RS-485 terminating resistors are SG 303
RDB(+) 410 Unlit 10M bps Pin Signal name Description separately needed. DB: RX/TX signal - signal 304
Lower side LED (link activity) 1 VP +5V bus power These are to be prepared by DB
RDA(-) 411 RSB(+) 407 RDB(+) 304
Color Green Data signal users. (390 Ω: 2 pcs. 220 Ω: DA: RX/TX signal + signal 305
2 RxD/TxD-P 110Ω
Lit Linked (positive data receive/transmit) 1 pc., or an active
RSA(-) 408 RDA(-) 305
Data signal terminator.)
Blink Active 3 RxD/TxD-N DA Not used 306
(negative data recive/transmit)
Unlit Link failure SG 409
4 DGND Signal ground CHK(red) 307
5 SHIELD Shield ground (Lit: User profile error/Adress error, Unlit: Normal
L ERR(red)
LED Lit Unlit Contact input / Contact output DI/DO (Suffix code: Type 2=2) 308
RS-485 (Lit: Communication failure(CRC error), Unlit: Normal
CHK L RUN(green)
(red) User profile error Normal External contact input 309
RSB(+) 407 (Lit: Normal, Unlit: No carrier detected/Communication timeout)
Normal No power, or No-voltage UT Transistor UT
RDY Communicating Communication contact contact
(green) successfully failure RSA(-) 408 COM
Common 301 COM 301
Not connected, or +5V
ERR Normal SG 409 DI11
(red) communication
failure (flashing) Factory default: No function 302 DI11 302 RS-485 communication/24 V DC loop power supply
+5V
DI12 RS-485 24 V DC loop power supply
Factory default: No function 303 DI12 303 RS485/LPS24
Contact rating: 12 V DC, 10 mA or more RSB(+) 301
(Suffix code: Type 2=1 and
CC-Link communication (with Modbus master) DeviceNet communication (with Modbus master) + 305 option code /LP)
Function can be 21.6-28.0 V DC
External contact output RSA(-) 302 (Max. 30 mA DC)
DA CC-L CAN_H DNET assigned to the - 306
1 1 UT terminals with no
CHK 110Ω (Suffix code: Type 3=3) 121Ω (Suffix code: Type 3=5,
2
Factory default: No function DO12 304 SG 303
DB 2 function.
CHK CAN_L except Type 2=3)
3 If the UT is located at 3
L ERR the end of a segment If the UT is located at the Factory default: No function DO11 305
4 4
L RUN for the CC-Link MNS end of a segment for the
5 5 DeviceNet
communication wiring,
communication wiring, Common COM 306
terminating resistors
Pin Signal name Description Pin Signal name Description terminating resistors are
are separately needed.
1 FG Flame ground These are to be 1 V+ DeviceNet power supply 24V separately needed. Transistor contact rating: 24 V DC, 50 mA
2 SLD Shield prepared by users. 2 CAN_H RX/TX + signal These are to be
3 DG RX/TX signal ground (110 Ω: 1 pc.) 3 DRAIN Shield/Drain wire prepared by users. (121
Ω: 1 pc.)
4 DB RX/TX - signal 4 CAN_L RX/TX - signal
5 DA RX/TX + signal 5 V- DeviceNet power supply common

LED Lit Unlit LED Lit/flashing Unlit

CHK User profile error/ CHK
(red) Address error Normal User profile error Normal
(red)
RS-485 RS-485
Normal. Communicating
L ERR Communication failure successfully (green, lit).
Normal RSB(+) 407 Not connected (green, flashing). RSB(+) 407
(red) (CRC error)
MNS Critical link failure (red, lit).
RSA(-) 408 (green/ Communication timeout (red, No electricity
No carrier RSA(-) 408
L RUN Normal detected/ red) flashing)
(green) Communicating successfully Communication SG 409 At power-on/Communication SG 409
timeout faulted (green/red, flashing)

,0 3 ' (1 SD H