PROJECT 6545 SOCAR CHIRAG 2 - 84 INCH PILE AXIAL CAPACITY Js (s/m) Jp (s/m) Qs (mm) Qp (mm)

ENGINEER B. BANERJEE DATE= 27-Nov-21 DRIVABILITY SAND 0.164 0.492 2.540 2.540
PARAMETERS CLAY 0.656 0.164 2.540 2.540
PILE AXIAL CAPACITY/DRIVING RESISTANCE CALCULATION : ALL INPUT DATA ARE SHADED 12.80 Overburden reduction depth (m) for local scour
Clay Friction Coefficient "Alpha" (w.r.t. New API) is reduced to 0.2 for values of "Si" > 2.5 Input diameter factor or leave blank for 6D
For long piles, "Length Correction Factor" (auto) = 1.215 - 0.0043 L/D ...(for L/D from 50 to 120). Input scour type : local (blank) or Global (1)
THE VALUES SHOWN BELOW MAY BE USED IN THE ABSENCE OF GIVEN DATA Specified Scour (m) : (-)ve for auto calculation
g Use10 kPa For Sand or Clay (Approximate Submerged Soil Density) Current Velocity (m/sec) : for sand auto calculation
For Sand VERY LOOSE LOOSE MEDIUM DENSE VERY DENSE=>Classification 2.13 Clay Auto Scour (m) Clay friction : Use 0 for New API,
f = d + 5 Use 20 Use 25 Use 30 Use 35 Use 40 => Degree 2.13 Sand Auto Scour (m) 1 for old.1, 2 for old.2 3
Drivability : Qp = Qs = 2.54 mm (0.1") : Jp = 0.492 secs/m(0.15 secs/ft) Q = Quake, J = Damping 67.0 Pile Submerged Density Length corr factors :
Js(Sand) = 0.164 (0.05), Js(Clay) = 0.656 (0.2) s/m (s/ft) Subscripts p = point, s = side 1.0 1.0 (factors for sand) 0 for auto correction,
PILE DIA THICKNESS ENETRATION AT COEFF KNO OF CURVES INCREMENT SCOUR USED SOIL RESISTANCE FACTORS Use1,1 for Static Capacity 1 for no corr. Or any
(m) (m) (m) (FOR SAND) 13 OF DEPTH (m) (m) SKIN END BRG Use 0.5,1.0 for Drivability known value 1.00
2.1340 0.0600 150.00 0.7 13 11.54 0.00 1.0 1.0 (factors for clay) At final pen 1.00
ALL SOIL ALL SOIL CLAY ONLY ALL SOIL ALL SOIL ALL SOIL ALL SOIL CLAY ONLY ALL SOIL ALL SOILSAND ONLY ALL SOIL CLAY ONLY
AUTO INPUT AUTO INPUT AUTO INPUT MAN. INPUT MAN. INPUT MAN. INPUT AVERAGE MAN. INPUT ND BEARING MAN. INPUTMAN. INPUTNO OF DEPTH Coefficient
DEPTH (m) g (KN/M*3) Cu (kPa) tu or f(lim) DEPTH (m) g (KN/M*3) g (KN/M*3) An Cu (kPa) INCREASE qu or q(lim) f INCREMENTS y
Below Scour Soil Density Shear Strength Friction (kPa) Below Mudline Soil Density Soil Density Shear Strength FACTOR End Brg(kPa)Friction Angle Below Scour (Friction)
0.00 7.00 5.00 0.00 7.00 7.00 5.00 1.00 0 -
4.00 7.00 10.00 4.00 7.00 7.00 10.00 1.00 1 0.36
4.00 7.00 25.00 4.00 7.00 7.00 25.00 1.00 2 0.89
10.00 7.00 35.00 10.00 7.00 7.00 35.00 1.00 3 0.50
10.00 8.50 35.00 10.00 8.50 7.00 35.00 1.00 4 0.50
20.00 8.50 55.00 20.00 8.50 7.75 55.00 1.00 5 0.35
40.00 9.30 95.00 40.00 9.30 8.33 95.00 1.00 6 0.29
60.00 9.30 135.00 60.00 9.30 8.65 135.00 1.00 7 0.26
80.00 9.30 175.00 80.00 9.30 8.81 175.00 1.00 8 0.25
100.00 9.30 215.00 100.00 9.30 8.91 215.00 1.00 9 0.24
100.00 7.50 215.00 100.00 7.50 8.91 215.00 1.00 10 0.24
106.00 7.50 215.00 106.00 7.50 8.83 215.00 1.00 11 0.23
120.00 7.50 242.00 120.00 7.50 8.68 242.00 1.00 12 0.23
150.00 7.50 300.00 150.00 7.50 8.44 300.00 1.00 13 0.24
- - - - - 14 -
- - - - - 15 -
- - - - - 16 -
- - - - - 17 -
- - - - - 18 -
- - - - - 19 -
- - - - - 20 -
- - - - - 21 -
- - - - - 22 -
- - - - - 23 -

Page
 - - - - - 24 -
- - - - - 25 -
- - - - - 26 -
- - - - - 27 -
- - - - - 28 -
- - - - - 29 -
- - - - - 30 -
- - - - - 31 -
- - - - - 32 -
- - - - - 33 -
- - - - - 34 -
- - - - - 35 -
- - - - - 36 -
- - - - - 37 -
- - - - - 38 -
- - - - - 39 -
- - - - - 40 -
- - - - - 41 -
- - - - - 42 -
- - - - - 43 -
- - - - - 44 -
- - - - - 45 -
- - - - - 46 -
- - - - - 47 -
- - - - - 48 -
- - - - - 49 -
- - - - - 50 -
X(m)from scour g (KN/M*3) Cu (kPa) tu or f(lim) X(m) from ML g (KN/M*3) g (KN/M*3) An Cu (kPa) EB Inc factor qu or q(lim) f INCREMENTS y

Page
PARAMETERS FOR CAPACITY CALCULATIONS

PLUG AREA STEEL AREA STEEL/PLUG PERIMETER (Ext+Int)/Ext = (Do+Di)/Do

3.5767 0.3909 0.1093 6.7042 1.9438 kN, m UNITS
DEPTH X (m) SKIN FRICTIONOVERBURDEN PILE MANUAL CAPACITY (kAUTO FRICTIONAUTO END BRG SAND COEFFICIENTS TO API FIG. 6.8.6-1 CLAY ONLY PILE AUTO CAPACITY (kN)
Below Mudline RED. FACTOR Pressure (kPa) PLUGGED OPEN tu (kPa) qu(kPa) C1 C2 C3 a PLUGGED OPEN
0.00 1.00 0.0 0.0 0.0 5.00 45.00 - - - 1.00 161.0 17.6
4.00 1.00 28.0 0.0 0.0 10.00 90.00 - - - 1.00 523.0 426.1
4.00 1.00 28.0 0.0 0.0 24.74 225.00 - - - 0.99 1005.9 478.9
10.00 1.00 70.0 0.0 0.0 30.99 315.00 - - - 0.89 2448.6 2692.8
10.00 1.00 70.0 0.0 0.0 30.99 315.00 - - - 0.89 2448.6 2692.8
20.00 1.00 155.0 0.0 0.0 37.24 495.00 - - - 0.68 5379.5 7208.7
40.00 1.00 333.0 0.0 0.0 66.50 855.00 - - - 0.70 13622.0 20868.1
60.00 1.00 519.0 0.0 0.0 94.50 1215.00 - - - 0.70 25703.3 41989.3
80.00 1.00 705.0 0.0 0.0 122.50 1575.00 - - - 0.70 41538.9 70408.0
100.00 1.00 891.0 0.0 0.0 150.50 1935.00 - - - 0.70 61128.9 106124.2
100.00 1.00 891.0 0.0 0.0 150.50 1935.00 - - - 0.70 61128.9 106124.2
106.00 1.00 936.0 0.0 0.0 150.50 1935.00 - - - 0.70 67182.7 117891.5
120.00 1.00 1041.0 0.0 0.0 169.40 2178.00 - - - 0.70 83064.5 147167.6
150.00 1.00 1266.0 0.0 0.0 210.00 2700.00 - - - 0.70 123084.9 221532.9
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -

Page
 - - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
- - - - - - - - - - - - -
DEPTH X (m) SKIN FRICTIONOVERBURDEN PILE MANUAL CAPACITY (AUTO FRICTIONAUTO END BRG SAND COEFFICIENTS TO API FIG. 6.7.6-CLAY ONLY PILE AUTO CAPACITY (kN)
Below Mudline RED. FACTOR Pressure (kPa) PLUGGED OPEN tu (kPa) qu(kPa) C1 C2 C3 a PLUGGED OPEN

NOTES ON AXIAL CAPACITIES

1. Length correction factors are incorporated in 'ALPHA (clay)'.
2. Auto capacities are calculated using API equations.

Page
 DEPTH DRIVABILITY/CAPACITY DATA DRIVABILITY PARAMETERS SOIL TYPE CAPACITY/SRD (MN)
Below Mudline End Bearing Damping (Jp) Skin Friction Damping (Js) skin friction side damping overall damping FOR API API API API
(m) (kN) (secs/m) (kN) (secs/m) (% of SRD) (secs/m) (secs/m) REFERENCE (auto-comp) (auto-tens) (New) (OLD.2)
0.0 17.6 0.164 0.0 0.656 0.0 0.656 0.656 CLAY 0.018 0.000 0.018 0.018
4.0 35.2 0.164 390.9 0.656 91.7 0.656 0.615 CLAY 0.426 0.391 0.384 0.426
4.0 88.0 0.164 390.9 0.656 81.6 0.656 0.566 CLAY 0.479 0.391 0.436 0.479
10.0 1126.7 0.164 1322.0 0.656 54.0 0.656 0.430 CLAY 2.449 1.322 1.956 2.449
10.0 1126.7 0.164 1322.0 0.656 54.0 0.656 0.430 CLAY 2.449 1.322 1.956 2.449
20.0 1770.5 0.164 3609.1 0.656 67.1 0.656 0.494 CLAY 5.380 3.609 5.091 5.380
40.0 3058.1 0.164 10563.9 0.656 77.6 0.656 0.546 CLAY 13.622 10.564 15.435 12.348
60.0 4345.7 0.164 21357.6 0.656 83.1 0.656 0.573 CLAY 25.703 21.358 31.558 21.346
80.0 5633.3 0.164 35905.7 0.656 86.4 0.656 0.589 CLAY 41.539 35.906 53.451 33.025
100.0 6920.9 0.164 54208.0 0.656 88.7 0.656 0.600 CLAY 61.129 54.208 80.884 47.385
100.0 6920.9 0.164 54208.0 0.656 88.7 0.656 0.600 CLAY 61.129 54.208 80.884 47.385
106.0 6920.9 0.164 60261.9 0.656 89.7 0.656 0.605 CLAY 67.183 60.262 89.533 51.710
120.0 7790.0 0.164 75274.5 0.656 90.6 0.656 0.610 CLAY 83.064 75.274 111.849 63.302
150.0 9657.0 0.164 113427.9 0.656 92.2 0.656 0.617 CLAY 123.085 113.428 168.220 92.421
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -

Page
 - - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
- - - - - - - - CLAY - -
DEPTH (m) DRIVABILITY DATA DRIVABILITY PARAMETERS SOIL TYPE CAPACITY/SRD (MN)
Below Mudline End Bearing Damping (Jp) Skin Friction Damping (Js) % skin friction side damping Av. Damping REFERENCE (auto-comp) (auto-tens) full setup Alpha @ 0.7
NOTES ON FULL SET-UP VALUES AND GRAPHS
1. Full setup values are created using the same spread-sheet by altering the values in shaded cells between H, M, 10 and 15, as appropriate.
2. Full setup values are copied (using 'PASTE SPECIAL' from the 'EDIT' menu) to column M (shaded row 140 to 190) from column L, if it is to be drawn with the SRD values, or left blank if not required.
3. When the number of points (Cell E14) is less than 50, the graph is adjusted by double-clicking on the graph and using 'EDIT SERIES' from the 'CHART' menu to reduce the number of points.

Page
 PROJECT NO : 6545 SOCAR : 84 INCH PILE CAPACITY

100.0

90.0 DESIGN
API Commentary - 2
API Main Section
80.0 Modified API Compression (alpha =
0.7)
Modified API Tension (alpha = 0.7)
PILE (1.6m OD X 60mmWT) AXIAL CAPACITY (MN)

70.0

60.0

50.0

40.0

30.0

20.0

10.0

0.0
0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 80.0 90.0 100.0 110.0 120.0 130.0 140.0 150.0
DEPTH BELOW MUDLINE (m)
FIGURE 2.2-1

Page