ELECTRICAL ENGINEERING DEPARTMENT

POLITEKNIK UNGKU OMAR

SESSION : 1 2020/2021

COURSE CODE : DET10013

COURSE TITLE : ELECTRICAL TECHNOLOGY
ASSESSMENT : PRACTICAL TEST
COURSE SECTION : _________________________________________
LECTURER’S NAME : _________________________________________
DATE : ___ / ___ / ______
DURATION : 2 hours

INSTRUCTION:

1. Answer All Questions.

2. All answer must base on measurement, not calculation
3. Calculator is disallowed during the test period

REGISTRATION
NAME CLO MARKS
NUMBER

2 / 30

TOTAL
30

Prepared by : Checked and Verified by:

CHE MUNIRA BINTI CHE RAZALI

PENYELARAS KURSUS
TEKNOLOGI ELEKTRIK (DET10013)
JABATAN KEJURUTERAAN ELEKTRIK
POLITEKNIK UNGKU OMAR

Practical Test DET10013 – Session 1 2020/2021

 PRACTICAL SKILL ASSESSMENT (PLO5/P4/CLS3a /CLO2)

Circuit Connection Scoring Table (Procedure 3)

Score Description

Score
Aspect
1 2 3

Student failed to set the Student was able to set the

Student was able to set the
Power Supply required voltage and required voltage but failed connect
required voltage and connect
Connection connect correct terminal correct terminal with the circuit or
correct terminal with the circuit
with the circuit vice versa.

Student failed to construct Student was able to construct one Student was able to construct
Connection of
the resistor correctly on the of the resistor leg correctly on the both resistor legs correctly on
Resistor R1
project board project board the project board

Student failed to construct Student was able to construct one Student was able to construct
Connection of
the resistor correctly on the of the resistor leg correctly on the both resistor legs correctly on
Resistor R2
project board project board the project board

Student failed to construct Student was able to construct one Student was able to construct
Connection of
the resistor correctly on the of the resistor leg correctly on the both resistor legs correctly on
Resistor R3
project board project board the project board

Student failed to construct Student was able to construct one Student was able to construct
Connection of
the resistor correctly on the of the resistor leg correctly on the both resistor legs correctly on
Resistor R4
project board project board the project board

Result /15

Total /30

Practical Test DET10013 – Session 1 2020/2021

 PRACTICAL TEST
EQUIPMENT : Power Supply, Proto-board, multimeter

COMPONENTS : Resistors 47Ω (1), 100Ω (1), 150Ω (1), 220Ω (1)

PROCEDURES :

1. Measure battery and each resistor used in this test and record your readings in Table 1.
2. Connect the circuit as shown in Figure 1.
3. Measure the total resistance across terminals AB and record your answer in Table 2 (without the
power supply, E connected).
4. Connect the circuit to the DC power supply and measure the output of the DC power supply
terminals AB by slowly adjusting the voltage knob, until the multimeter scale reads 6V.
5. Measure the voltage drop across the resistors R1 (V1), R2 (V2), R3 (V3), R4 (V4), and the terminals
AB (VT) and record the readings in the Table 2.
6. Measure the current flowing through R1, R2, R3, R4 and the total current (IT) and record the
readings in Table 2.
7. Student should record all procedure (1) until (6) and submit your video to link provided by
lecturer.

I1
A

IT

6V

I2 I4
B

I3 Figure 1

Practical Test DET10013 – Session 1 2020/2021

RESULTS:

Measured battery:

Nominal Value R1 = 100Ω R2= 150Ω R3 = 47Ω R4 = 220Ω

Measured Value
Table 1 (4 marks)_

Voltage Drop Current

RT (Ω) (Volts) (miliAmpere)
V1 V2 V3 V4 VT I1 I2 I3 I4 IT

Measured
value

Table 2
(11 marks)

Practical Test DET10013 – Session 1 2020/2021