Rino 750/755t

Owner’s Manual
© 2016 Garmin Ltd. or its subsidiaries
All rights reserved. Under the copyright laws, this manual may not be copied, in whole or in part, without the written consent of Garmin. Garmin reserves the right to change or improve its
products and to make changes in the content of this manual without obligation to notify any person or organization of such changes or improvements. Go to www.garmin.com for current updates
and supplemental information concerning the use of this product.
Garmin , the Garmin logo, ANT+ , Auto Lap , BlueChart , City Navigator , Rino , TracBack , and VIRB are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other
® ® ® ® ® ® ® ®

countries. BaseCamp™, chirp™, Connect IQ™, Garmin Connect™, Garmin Express™, HomePort™, and tempe™ are trademarks of Garmin Ltd. or its subsidiaries. These trademarks may not be
used without the express permission of Garmin.
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Garmin is under license. Apple and Mac are trademarks of Apple Inc., registered in the
® ® ®

U.S. and other countries. NMEA , NMEA 2000 , and the NMEA 2000 logo are registered trademarks of the National Marine Electronics Association. microSD and the microSDHC logo are
® ® ®

trademarks of SD-3C, LLC. Windows is a registered trademark of Microsoft Corporation in the United States and other countries. Other trademarks and trade names are those of their respective
®

owners.
 Table of Contents Removing Your Device Registration From Geocaching.com ..... 7
Activities......................................................................... 7
Introduction.....................................................................1 Recording an Activity .................................................................. 7
Device Overview ......................................................................... 1 Creating a New Activity ............................................................... 8
Battery Information ................................................................. 1 Editing an Activity Name ........................................................ 8
Installing the Lithium-ion Battery ............................................ 1 Editing an Activity Icon ........................................................... 8
Installing AA Batteries ............................................................ 1 Deleting an Activity ..................................................................... 8
Turning On the Device ................................................................ 2 Customizing Your Activity Log .................................................... 8
Device Operation ........................................................................ 2 Pausing an Activity ..................................................................... 8
Opening the App Drawer ....................................................... 2 Saving the Current Activity ......................................................... 8
Viewing Widgets .................................................................... 2 Clearing the Current Activity ....................................................... 8
Locking the Touchscreen ....................................................... 2 Deleting an Activity History ......................................................... 8
Turning On Battery Save Mode ............................................. 2 Viewing Activity Information ........................................................ 8
Acquiring GPS Signals ............................................................... 3 Viewing the Elevation Plot of an Activity ..................................... 8
Radio............................................................................... 3 Saving a Location on an Activity ................................................. 8
Transmitting ................................................................................ 3 Opening Track Manager ............................................................. 8
The Radio App ............................................................................ 3 Navigation....................................................................... 9
Opening the Radio App ......................................................... 3 Navigating to a Destination ......................................................... 9
Adjusting the Radio Volume ................................................... 3 Finding a Location Near Another Location ............................ 9
Adjusting the Squelch Level .................................................. 3 Stopping Navigation ............................................................... 9
Channels and Codes .................................................................. 3 Navigating with the Map ............................................................. 9
Selecting a Channel ............................................................... 3 Navigating Using TracBack® ...................................................... 9
Selecting a Squelch Code ..................................................... 4 Optional Maps ............................................................................. 9
Monitoring a Channel for Activity ........................................... 4 Finding an Address ................................................................ 9
Scanning Channels ................................................................ 4 Navigating with the Compass ..................................................... 9
Repeater Channels ................................................................ 4 Calibrating the Compass ........................................................ 9
Peer-to-Peer Positioning ............................................................. 4 Course Pointer ....................................................................... 9
Polling Other Rino Users ....................................................... 4 Navigating with Sight 'N Go ........................................................ 9
Editing Your Contact Info ....................................................... 4 Elevation Plot ............................................................................ 10
Contacts ...................................................................................... 4 Navigating to a Point on the Elevation Plot .......................... 10
Saving a New Contact ........................................................... 4 Changing the Plot Type ....................................................... 10
Viewing Contacts on the Map ................................................ 4 Resetting the Elevation Plot ................................................. 10
Navigating to a Contact .......................................................... 4 Calibrating the Barometric Altimeter .................................... 10
Notes .......................................................................................... 4 Waypoints..................................................................... 10
Creating, Saving, and Sending Notes .................................... 4
Marking Your Current Location as a Waypoint ......................... 10
Emergency Alerts ....................................................................... 5
Finding a Waypoint ................................................................... 10
Sending an Emergency Alert ................................................. 5
Editing a Waypoint .................................................................... 10
Responding to an Emergency Alert ....................................... 5
Deleting a Waypoint .................................................................. 10
Radio App Settings ..................................................................... 5
Increasing the Accuracy of a Waypoint Location ...................... 10
Radio Setup ........................................................................... 5
Projecting a Waypoint ............................................................... 10
Connected Features....................................................... 5 Routes........................................................................... 10
Pairing Your Smartphone ........................................................... 5
Creating a Route Using Route Planner .................................... 10
Connect IQ Features .................................................................. 5
Creating a Route Using the Map .............................................. 11
Downloading Connect IQ Features ........................................ 5
Editing the Name of a Route .................................................... 11
Weather........................................................................... 5 Editing a Route ......................................................................... 11
Monitoring SAME Weather Alerts ............................................... 6 Viewing a Route on the Map .................................................... 11
Opening the Weather App .......................................................... 6 Deleting a Route ....................................................................... 11
Viewing Weather Conditions and Forecasts .......................... 6 Viewing the Active Route .......................................................... 11
Viewing SAME Weather Alerts on the Map ........................... 6 Reversing a Route .................................................................... 11
Geocaches...................................................................... 6 Viewing the Elevation Plot of a Route ...................................... 11
Registering Your Device at Geocaching.com ............................. 6 Camera and Photos...................................................... 11
Connecting to Geocaching.com ............................................. 6 Taking a Photo ..........................................................................11
Searching for a Geocache .......................................................... 6 Applications.................................................................. 11
Navigating to a Geocache .......................................................... 6
Sending and Receiving Data Wirelessly ................................... 11
Using Hints and Clues to find a Geocache ............................ 6
Setting a Proximity Alarm ......................................................... 11
Logging the Attempt .................................................................... 6
Calculating the Size of an Area ................................................ 12
Filtering the Geocache List ......................................................... 7
Viewing the Calendar and Almanacs ........................................ 12
Saving a Custom Geocache Filter ......................................... 7
Setting an Alarm ....................................................................... 12
Editing a Custom Geocache Filter ......................................... 7
Starting the Countdown Timer .................................................. 12
Applying a Custom Filter to a Geocache List ......................... 7
Opening the Stopwatch ............................................................ 12
Downloading Geocaches Using a Computer .............................. 7
Satellite Page ............................................................................12
chirp ............................................................................................ 7
Changing the Satellite View ................................................. 12
Enabling chirp Searching ....................................................... 7
Turning Off GPS .................................................................. 12
Finding a Geocache with a chirp ............................................ 7
Simulating a Location ........................................................... 12
Removing Live Geocache Data from the Device ........................ 7

Table of Contents i
Controlling a VIRB® Action Camera ......................................... 12 Deleting Files ....................................................................... 18
Phone Notifications ................................................................... 12 Disconnecting the USB Cable .............................................. 18
Hiding Notifications .............................................................. 12 Specifications ............................................................................ 18
Fitness........................................................................... 12 Radio Frequency Charts ...................................................... 18
History ....................................................................................... 12 FCC Licensing Information ....................................................... 20
Viewing an Activity History ................................................... 12 Viewing Device Information ...................................................... 20
Deleting an Activity from Your History ................................. 12 Troubleshooting........................................................... 20
Using Garmin Connect ......................................................... 12 My handheld device is not responding ..................................... 20
Optional Fitness Accessories ............................................... 12 My device does not turn on ...................................................... 20
About Heart Rate Zones ........................................................... 13 The battery gauge does not seem accurate ............................. 21
Fitness Goals ....................................................................... 13 My phone will not connect to the device ................................... 21
Setting Your Heart Rate Zones ............................................ 13 My device is not acquiring satellite signals ............................... 21
Customizing the Device............................................... 13 My device does not go into mass storage mode
Adjusting the Backlight Brightness ........................................... 13 automatically ............................................................................. 21
Customizing the Keys ............................................................... 13 I need to reset all settings back to factory default values ......... 21
Customizing the Main Menu ..................................................... 13 Appendix....................................................................... 21
Changing Items on the Main Menu ...................................... 13 tempe™ .................................................................................... 21
Customizing the Dashboard on the Main Menu ................... 13 Data Fields ................................................................................ 21
Customizing the App Drawer .................................................... 13 Heart Rate Zone Calculations ................................................... 22
Adding a Shortcut to the Main Menu ........................................ 14 Index.............................................................................. 24
Creating a Shortcut .............................................................. 14
Custom Data Fields and Dashboards ....................................... 14
Enabling the Map Data Fields .............................................. 14
Customizing the Data Fields ................................................ 14
Customizing Dashboards ..................................................... 14
Setting the Touchscreen Sensitivity ......................................... 14
Display Settings ........................................................................ 14
Configuring the Maps ................................................................ 14
Map Settings ........................................................................ 14
Advanced Map Settings ....................................................... 14
System Settings ........................................................................ 15
Satellite Settings .................................................................. 15
GPS and GLONASS ............................................................ 15
Appearance Settings ................................................................ 15
Setting the Device Tones .......................................................... 15
Routing Settings ....................................................................... 15
Heading Settings ...................................................................... 15
Altimeter Settings ...................................................................... 15
Position Format Settings ........................................................... 15
Changing the Units of Measure ................................................ 16
Time Settings ............................................................................ 16
Geocaching Settings ................................................................. 16
ANT+ Sensor Settings .............................................................. 16
Fitness Settings ........................................................................ 16
Setting Your Fitness User Profile ......................................... 16
Marking Laps by Distance .................................................... 16
Marine Settings ......................................................................... 16
Setting Up Marine Alarms .................................................... 16
Resetting Data and Settings ..................................................... 16
Restoring Default Values for Specific Settings .................... 16
Restoring Default Values for Specific Page Settings ........... 16
Device Information....................................................... 17
Attaching the Carabiner Clip ..................................................... 17
Headsets and Microphones ...................................................... 17
Product Updates ....................................................................... 17
Maximizing Battery Life ............................................................. 17
Device Care .............................................................................. 17
Cleaning the Device ............................................................. 17
Cleaning the Touchscreen ................................................... 17
Water Immersion .................................................................. 17
Data Management .................................................................... 17
File Types ............................................................................ 17
Installing a Memory Card ..................................................... 17
Connecting the Device to Your Computer ........................... 18
Transferring Files to Your Device ........................................ 18

ii Table of Contents
 Introduction
WARNING
See the Important Safety and Product Information guide in the
product box for product warnings and other important
information.

Device Overview

4 Turn the D-ring clockwise to secure the battery pack onto the
device.
Charging the Battery Pack
NOTICE
To prevent corrosion, thoroughly dry the USB port, the weather
cap, and the surrounding area before charging or connecting to
a computer.
Do not attempt to use the device to charge a battery that was
not provided by Garmin . Attempting to charge a battery that
®

was not provided by Garmin can damage the device and void
the warranty.
Before you can connect the straight connector of the USB cable
to your device, you may need to remove optional mount
accessories.
NOTE: The device does not charge when outside the approved
temperature range (Specifications, page 18).
You can charge the battery using a standard wall outlet or a
USB port on your computer.
GMRS antenna 1 Pull up the weather cap from the mini-USB port .
GPS antenna
Camera lens and flash (not available on all models)
Mini-USB port (under weather cap)
2.5 mm headset jack (under weather cap)
Battery cover D-ring
microSD card slot (under battery door)
®

Battery Information
WARNING 2 Plug the small end of the USB cable into the mini-USB port.
The temperature rating for the device may exceed the usable
range of some batteries. Alkaline batteries can rupture at high
3 Plug the USB end of the cable into an AC adapter or a
computer USB port.
temperatures.
Do not use a sharp object to remove batteries.
4 If necessary, plug the AC adapter into a standard wall outlet.
When you connect the device to a power source, the device
CAUTION turns on.
Contact your local waste disposal department to properly 5 Charge the battery completely.
recycle the batteries.
Saving Energy While Charging the Device
NOTICE You can turn off device features while charging.
Alkaline batteries lose a significant amount of their capacity as 1 Connect your device to an external power source.
the temperature decreases. Use lithium batteries when 2 Hold the power button until the screen turns off.
operating the device in below freezing conditions.
The device goes into a low power, battery charging mode,
Installing the Lithium-ion Battery and the battery gauge appears.
1 Locate the Lithium-ion battery pack included in the product 3 Charge the device completely.
box. Long-Term Storage
2 Align the metal contacts on the battery pack with the metal When you do not plan to use the device for several months,
contacts on the back of the device. remove the batteries. Stored data is not lost when batteries are
3 Press and hold the battery pack in place. removed.
Installing AA Batteries
Instead of the Lithium-Ion battery pack (Installing the Lithium-ion
Battery, page 1), you can use four alkaline, NiMH, or lithium AA
batteries with an optional AA battery pack (not included). This is

Introduction 1
useful when you are on the trail and cannot charge the Lithium-
Ion battery pack. Use NiMH or lithium batteries for best results.
The AA battery pack contains two parts.
1 If necessary, turn the D-ring counter-clockwise, and pull up to
remove the battery pack from the device.
2 Push down on the lever inside the AA battery pack to
separate the two parts .

Swipe down to view widgets (Viewing Widgets,

Widgets page 2) and the battery gauge.
Select to transmit an attention tone on the current
channel.
Hold to send an emergency alert (Emergency Alerts,
3 Insert four AA batteries, observing polarity. (Call key)
page 5).
You can customize the function of this key (Customizing
the Keys, page 13).
Select to adjust the backlight.
Hold to turn the device on or off.
(Power key)
Hold to transmit on the current radio channel
PTT (Transmitting, page 3).
(Push-to-talk)
Select the radio dashboard at the top of the main menu
Main menu to launch the radio app.
You can customize the dashboard on the main menu
(Customizing the Dashboard on the Main Menu,
page 13).
Select the shortcuts to launch applications.
4 Starting at the bottom, connect the two parts of the battery
You can customize the shortcuts on the main menu
pack together and press until the top locks into place.
(Customizing the Main Menu, page 13).
5 Align the metal contacts on the battery pack with the metal Select to adjust the volume.
contacts on the back of the device.
Volume keys
6 Press and hold the battery pack in place.
Swipe up to open apps and Connect IQ™ apps.

(App drawer)

Opening the App Drawer

The app drawer contains all of the applications used to operate
this device.
1 From the main menu, swipe up from the bottom of the
screen.
2 Swipe down from the top of the screen to return to the main
menu without launching an application (optional).
7 Turn the D-ring clockwise to secure the battery pack onto the
device. Viewing Widgets
Your device is preloaded with a widget that displays the status
Turning On the Device of your connections, battery level, and other information.
Hold . Additional widgets can be added from the Connect IQ app
(Connect IQ Features, page 5).
Device Operation 1 Swipe down from the top of the screen.
You can operate this device using a combination of hardware 2 Swipe left or right to view more widgets.
key and touchscreen actions. 3 Select to return to the previous screen.
Locking the Touchscreen
You can lock the screen to prevent inadvertent screen touches.
Select > .
Turning On Battery Save Mode
You can use battery save mode to prolong the battery life.
From the app drawer, select Setup > Display > Battery
Save > On.

2 Introduction
In battery save mode, the screen shuts off when the backlight TIP: You can also select the radio dashboard at the top of the
times out. You can select to turn on the screen. main menu to open the radio app.
Adjusting the Radio Volume
Acquiring GPS Signals
1 From any screen, select the volume keys to change the radio
When you turn on your navigation device, the GPS receiver volume.
must collect satellite data and establish the current location. The
time required to acquire satellite signals varies based on several The volume screen appears.
factors, including how far you are from the location where you 2 Select to mute or restore the radio volume (optional).
last used your navigation device, whether you have a clear view
of the sky, and how long it has been since you last used your Adjusting the Squelch Level
navigation device. The first time you turn on your navigation You can adjust the sensitivity level of the squelch to filter out
device, it may take several minutes to acquire satellite signals. unwanted background noise. When you increase the squelch
level, fewer weak background signals are heard.
1 Turn on the device.
2 Wait while the device locates satellites. 1 From any screen, select the volume keys.
The volume screen appears.
3 If necessary, go to an open area, away from tall buildings and
trees. 2 Select under the Squelch bar.
in the status bar indicates the satellite signal strength. When You should increase the squelch level until you no longer
at least half the bars are filled, the device is ready for navigation. hear the unwanted background noise.

Channels and Codes

Radio To communicate with other Rino and GMRS or UHF CBRS/PRS
In the United States and Canada, this device uses General radio users, you must be on the same channel.
Mobile Radio Service (GMRS) for two-way communication with Rino devices are compatible with third-party radios as long as
other compatible radio devices. the radios use standard frequencies. A list of all frequencies
In Australia, this device uses UHF Citizen Band Radio Service used by this device is available in the product specifications
(UHF CBRS), and in New Zealand, this device uses UHF (Radio Frequency Charts, page 18).
Personal Radio Service (PRS) for two-way communication with NOTE: GMRS frequencies are regulated by the FCC in the
other compatible radio devices. United States. To transmit on GMRS frequencies, you must
When communicating with other Garmin Rino devices, obtain a license from the FCC (FCC Licensing Information,
additional features are available. page 20).
United States and Canada Channel Number Channel Type
Transmitting 1 through 22 GMRS channels
To communicate with other Rino users or compatible radio 15R through 22R Repeater channels
devices, you must be on the same channel and code (Channels
and Codes, page 3). Australia and New Zealand Channel Channel Type
Number
1 Hold PTT.
9 through 30, 39, 40, 49 through 60, 64 UHF CBRS/PRS channels
2 Speak into the front of the device. through 70, 79, 80
3 After you are finished speaking, release PTT. 1R through 8R (31 through 38), 41R CBRS/PRS repeater
The radio transmits your position information. You cannot through 48R (71 through 78) channels1
hear incoming transmissions until your transmission is 5 and 35 Reserved channels
complete. A roger tone sounds on your radio and on the (emergency)
radios receiving your transmission to confirm that the 22 and 23 Reserved channels (data
transmission is complete. only)
NOTE: You can change or disable the roger tone (Setting the 61 through 63 Reserved channels (for future
Device Tones, page 15). use)

The Radio App Squelch codes allow you to filter calls from other users on the
same channel, so you hear only the radios you want to hear.
Using the radio app, you can view information about the radio,
Calls on the channel that are not using the same squelch code
control the radio channel and squelch codes, and customize the
in the same squelch tone mode are ignored.
radio features.
NOTE: Squelch codes do not make your conversation private.
Icons along the top of the radio page provide useful information
Anyone on the same channel can hear your conversation.
about the radio.
Squelch Tone Mode Squelch Codes
: Indicates the activity status of the radio. When an arrow is
pointing at the radio, the radio is receiving a transmission. Continuous Tone Controlled 1 through 38
When an arrow is pointing away from the radio, the radio is Squelch System (CTCSS)
transmitting. Digital-Coded Squelch (DCS) Listed in the product specifications
(Radio Frequency Charts, page 18)
: The radio is ready to transmit position information (Peer-to-
Peer Positioning, page 4).
: Weather alerts are enabled (Radio App Settings, page 5).
Selecting a Channel
1 From the radio app, select Channel.
: The radio is muted (Adjusting the Radio Volume, page 3).
2 Select or to change the channel.
Opening the Radio App 3 Select .
You can manage your channel, code, and other radio settings in
the radio app.
1 Communication with another CB station is not authorized within operational
From the app drawer, select Radio.
range of a CB repeater.

Radio 3
Selecting a Squelch Code After you send location information, the icon changes to a
1 From the radio app, select CTCSS or DCS. countdown timer so you know when location information can be
sent again.
2 Select or to change the code.
NOTE: Selecting Off allows you to hear everything on the Polling Other Rino Users
channel. You can request position updates for other Rino users who are
3 Select . in your saved contacts (Saving a New Contact, page 4).
NOTE: If you cannot hear calls on the same channel with the 1 From the contacts app, select a saved contact.
same code, verify all the radios are using the same squelch tone 2 Select Poll Location.
mode (Changing the Squelch Tone Mode, page 4). The location of the contact is updated on the map.
Changing the Squelch Tone Mode
Editing Your Contact Info
This device can use two types of squelch tone modes, CTCSS
From the radio app, you can change the symbol and name
and DCS. If you cannot hear calls on the same channel with the
transmitted to other Rino users through peer-to-peer positioning.
same code, make sure all the radios are using the same squelch
tone mode. • To change your name, select the name field.
1 From the radio app, select > Radio Setup > Squelch • To change your symbol, select the symbol.
Tone Mode.
2 Select a squelch tone mode. Contacts
You can save information about another Rino user as a contact.
Monitoring a Channel for Activity You can view location information and navigate to the location of
You can monitor a single channel for any activity, including static users in your contacts list.
and weak voice signals. This is helpful if a signal is going out of
range. Saving a New Contact
The first time the device receives a peer-to-peer positioning
1 From the radio app, select the channel you want to monitor.
signal from another Rino user, the new contact page appears.
2 Select Monitor. To save the contact details or navigate to the contact in the
future, you must save the new contact in your contacts list.
Scanning Channels
You can scan the channels for voice activity. This can help you From the new contact page, select Save.
find a channel with light activity for your group to use, or to find The new contact is saved in your contacts list.
other radio users in the area.
Viewing Contacts on the Map
From the radio app, select Scan.
1 From the main menu, select Contacts.
Configuring the Scan List TIP: To open the contacts app from the radio app, select .
By default, all available channels are included when scanning.
You can configure the scan list to include only specific channels
2 Select a contact.
and squelch codes. Selecting specific channels and codes 3 Select View Map.
reduces the scan time and may help prevent a missed
transmission.
Navigating to a Contact
1 From the app drawer, select Contacts.
1 From the radio app, select > Scanlist Setup.
TIP: To open the contacts app from the radio app, select .
2 Select one or more channels to remove from the list.
2 Select a contact.
3 To restrict the scan to the current squelch code, select >
Scan Current Codes (optional). 3 Select View Map > Go.
4 Select . 4 Follow to the contact's location.

Repeater Channels Notes

This device can use GMRS repeater channels in the United You can send short notes to other Rino users on your current
States, and CBRS/PRS repeater channels in Australia and New channel and code. You can review previously received notes
Zealand. GMRS repeater channels are not available in Canada. from your contacts. You can edit and save favorite notes to
Repeater channels use repeaters, when available, to enable quickly send them later.
communication around obstacles or increase transmission NOTE: Notes transmit to all users on your current channel and
distance. Position reporting is not allowed by the FCC on GMRS code, not just to your saved contacts.
repeater channels.
Creating, Saving, and Sending Notes
Peer-to-Peer Positioning 1 From the app drawer, select Notes.
You can send your location information to other Rino users TIP: To open the notes app from the radio app, select .
using peer-to-peer positioning. Through peer-to-peer 2 Select Send Note > New Note.
positioning, you can also track the movement of other Rino
users on the same channel and code, and navigate to their 3 Enter the note text.
locations. Due to FCC regulations, you can enter a maximum of 13
Peer-to-peer positioning is enabled by default, and your position characters in a note.
information is sent to other Rino users on the same channel and 4 Select .
code when you press the PTT key (push-to-talk) or the key 5 Select an option:
(call).
• To send the note without saving it, select Send Note.
NOTE: You can send location information only once every 30
• To save the note without sending it, select Save.
seconds, due to FCC restrictions.
• To save the note and send it, select Send and Save.

4 Radio
Emergency Alerts install the Garmin Connect™ Mobile app on the connected
You can send an emergency alert to all Rino users on the smartphone. Go to www.garmin.com/apps for more information.
current channel and code. Users can respond to an emergency Phone notifications: Displays phone notifications and
alert to immediately begin navigating to your position. messages on your Rino 750/755t device.
Activity uploads to Garmin Connect: Automatically sends
Sending an Emergency Alert
your activity to your Garmin Connect account as soon as you
To send emergency alerts to other Rino and GMRS or UHF finish recording the activity.
CBRS/PRS radio users, you must be on the same channel.
Connect IQ: Allows you to extend your device features with
1 Hold . widgets, data fields, and apps.
2 Select Yes. Software Updates: Allows you to update your device software.
The device sends an emergency alert every 60 seconds until EPO Downloads: Allows you to download an extended
another Rino user responds to the alert or you cancel the prediction orbit file to quickly locate GPS satellites and
alert. reduce the time it takes to calculate your position.
Responding to an Emergency Alert Live Geocache Data: Provides free and subscription-based
To receive emergency alerts from other Rino and GMRS or UHF services to view live geocache data from
CBRS/PRS radio users, you must be on the same channel. www.geocaching.com.
1 When you receive an emergency alert, select Help. Weather: Allows you to view current weather conditions and
The device sends a response to the alert sender, and begins weather forecasts. You can also view weather radar on the
navigation to the sender's location automatically. map.
2 Follow to the sender's location. Pairing Your Smartphone
1 Go to garmin.com/apps, and download the Garmin Connect
Radio App Settings Mobile app to your smartphone.
From the radio app, select .
2 Bring your smartphone within 10 m (33 ft.) of your device.
Turn Radio Off: Turns off the radio functionality. You cannot
make or receive transmissions when the radio functionality is 3 On your device, from the app drawer, select Setup >
turned off. Bluetooth, and follow the on-screen instructions.
Enable Weather Alert: Enables weather alert tones on the 4 From your smartphone, open the Garmin Connect Mobile
current channel or on all channels (Advanced Radio Setup, app, and follow the on-screen instructions to connect a
page 5). device.
The instructions are provided during the initial setup, or can
Radio Setup be found in the Garmin Connect Mobile app help.
From the radio app, select > Radio Setup. Phone notifications require a compatible smartphone
Send Location: Enables sending position information when you equipped with Bluetooth technology. Go to garmin.com/ble
transmit to other Rino users. for compatibility information.
Allow Polling: Allows polling requests from other Rino users.
Power Level: Sets the power level used to transmit using Connect IQ Features
GMRS channels in the United States and Canada, and UHF You can add Connect IQ features to your device from Garmin
CBRS/PRS channels in Australia and New Zealand. If the and other providers using the Connect IQ Mobile app. You can
battery level is too low to support transmissions using higher customize your device with data fields, widgets, and apps.
power levels, the value of this setting decreases Data Fields: Allow you to download new data fields that present
automatically. sensor, activity, and history data in new ways. You can add
Squelch Tone Mode: Sets the squelch mode (Changing the Connect IQ data fields to built-in features and pages.
Squelch Tone Mode, page 4). Widgets: Provide information at a glance, including sensor data
Repeater Channel: Enables the GMRS repeater channels in and notifications.
the United States, and the CBRS/PRS repeater channels in Apps: Add interactive features to your device, such as new
Australia and New Zealand. GMRS repeater channels are not outdoor and fitness activity types.
available in Canada (Repeater Channels, page 4).
Downloading Connect IQ Features
Advanced Radio Setup
Before you can download features from the Connect IQ app, you
From the radio app, select > Radio Setup > Advanced must pair your Rino device with your smartphone (Pairing Your
Setup. Smartphone, page 5).
Headset Type: Sets the type of accessory headset or 1 From the app store on your smartphone, install and open the
microphone you are using with the device (Headsets and Connect IQ app.
Microphones, page 17).
2 If necessary, select your device.
VOX Level: Sets the sensitivity of a connected Voice Operated
Transmission (VOX) accessory. A lower VOX setting is 3 Select a Connect IQ feature.
recommended for quiet environments, and a higher VOX 4 Follow the on-screen instructions.
setting is recommended for noisy environments.
Weather Alert: Sets the channels that are monitored for
weather alerts when weather alerts are enabled. Weather
The weather app preloaded on this device provides weather
information from two sources.
Connected Features • When connected to a smartphone, the device provides
Connected features are available for your Rino 750/755t device current weather conditions, forecasts, and weather-radar
when you connect the device to a compatible smartphone using information from the Internet.
Bluetooth wireless technology. Some features require you to
®

Connected Features 5
• When set to monitor for weather broadcasts, the device can 3 Select Confirm Registration.
receive radio-transmitted Specific Area Message Encoding
(SAME) county weather alerts. Connecting to Geocaching.com
After you register, you can view geocaches from
Monitoring SAME Weather Alerts www.geocaching.com on your device while connected
wirelessly.
SAME weather alerts allow you to receive radio-transmitted
county weather alerts on your device. • Connect to the Garmin Connect app.
NOTE: SAME weather alerts are available in the United States
only. Searching for a Geocache
You can search the geocaches loaded on your device. If you are
1 From the radio app, select Weather. connected to geocaching.com, you can search live geocache
2 Select a channel. data and download geocaches.
You can receive weather alerts only on the selected weather NOTE: You can download detailed information for more than
channel. three geocaches per day with a premium membership. Go to
When you receive a weather alert on the selected channel, a www.geocaching.com for more information.
message appears containing the alert information. 1 From the app drawer, select Geocaching.
2 Select > .
Opening the Weather App
3 Select an option:
From app drawer, select Weather.
• To search the geocaches loaded on your device by name,
Viewing Weather Conditions and Forecasts select Spell Search, and enter a search term.
To view forecast and weather radar information, your device • To search for geocaches near you or near another
must have an internet connection. You can connect to a location, select Search Near, and select a location.
smartphone with internet access (Pairing Your Smartphone,
If you are connected to geocaching.com, the search
page 5).
results include live geocache data obtained by GC Live
You can view weather conditions and forecasts, and view Download or by selecting the refresh button on the map.
weather radar on the map. When the map is dark, no weather
• To search for nearby geocaches on the map, select .
data is loaded on the device, or the device is out of coverage.
Weather data is not available for out-of-coverage areas on the If you are connected to geocaching.com, you can select
map. to refresh live geocaches that are near your location on
the map.
When you view a weather radar frame, the device displays the
current time for the frame. • To search for live geocaches by code, select GC Live
Download.
1 From the app drawer, select Weather.
This feature allows you to download a specific geocache
2 Select an option: from geocaching.com when you know the geocache code.
• To view the weather radar on the map, select .
4 Select to filter the search results (optional).
TIP: You can animate or pause the weather map. When
you stop the animation, the device displays the most 5 Select a geocache.
recent weather data. The geocache details appear. If you selected a live geocache
and you are connected, the device downloads the full
• To view current weather conditions and forecasts, select
geocache details to the internal storage, if necessary.
.
Viewing SAME Weather Alerts on the Map Navigating to a Geocache
To view SAME radio weather alerts on the map, you must 1 Search for a geocache.
monitor for the alerts (Monitoring SAME Weather Alerts,
page 6).
2 From the geocache details, select Go.
You can view a county map with color-coded SAME watches
3 Navigate using the map (Navigating with the Map, page 9)
or compass (Navigating with the Compass, page 9).
and warnings.
4 As you approach the location of the geocache, use the hints
1 From the weather app, select . and clues to help you find the hidden cache (Using Hints and
2 Drag the map to view available watches and warnings in the Clues to find a Geocache, page 6).
county (optional).
3 Select a shaded area and the name of the alert to view more Using Hints and Clues to find a Geocache
detailed information about an alert (optional). You can use hints or clues, such as a description or coordinates,
to help you find a geocache.
1 While navigating to a geocache, select the geocache name.
Geocaches 2 Select an option:
Geocaching is a treasure hunting activity in which players hide • To view details about the geocache, select Description.
or search for hidden caches using clues and GPS coordinates. • To view a clue about a geocache location, select Hint.
• To view latitude and longitude for a geocache, select
Registering Your Device at Geocaching.com Coordinates.
You can register your device at www.geocaching.com to search
for a list of nearby geocaches, or to search live information for • To view feedback about the geocache from previous
millions of geocaches. searchers, select Logs.
1 From the app drawer, select Setup > Geocaching > • To turn chirp™ searching on, select chirp.
Register Device.
An activation code appears.
Logging the Attempt
After you attempt to find a geocache, you can log your results.
2 Follow the on-screen instructions.

6 Geocaches
1 While navigating to a geocache, from the app drawer, select 2 Go to www.geocaching.com.
Geocaching > Log. 3 If necessary, create an account.
2 Select Found, Did Not Find, Needs Repair, or 4 Sign in.
Unattempted.
5 Follow the instructions at geocaching.com to find and
3 Select an option: download geocaches to your device.
• To begin navigation to the next geocache nearest you,
select Find Next Closest. chirp
• To stop logging, select Done. A chirp is a small Garmin accessory that is programmed and left
• To enter a comment about looking for the cache or about in a geocache. You can use your device to find a chirp in a
the cache itself, select Edit Comment, enter a comment, geocache. For more information about the chirp, see the chirp
and select . Owner's Manual at www.garmin.com.
If you are connected to geocaching.com, the log is uploaded to Enabling chirp Searching
your geocaching.com account automatically. 1 From the app drawer, select Setup > Geocaching.
Filtering the Geocache List 2 Select chirp Searching > On.
You can filter your geocache list based on certain factors, such Finding a Geocache with a chirp
as the level of difficulty. 1 With chirp searching enabled, navigate to a geocache.
1 From the app drawer, select Geocaching > . When you are within approximately 10 m (33 ft.) of the
2 Select one or more option to filter: geocache that contains a chirp, details about the chirp
appear.
• To filter by a geocache category, such as puzzle or event,
select Type. 2 Select Show Details.
• To filter by the physical size of the geocache container, 3 If necessary, select Go to navigate to the next stage of the
select Cache Size. geocache.
• To filter by Unattempted, Did Not Find, or Found
geocaches, select Status. Removing Live Geocache Data from the
• To filter by the GPX file, live data, or pocket queries you Device
have downloaded, select Geocache Files. You can remove live geocache data to show only geocaches
• To filter by the difficulty level of finding the geocache, or manually loaded on the device using a computer.
the difficulty of the terrain, use the slider bars to adjust the From the app drawer, select Setup > Geocaching >
difficulty levels. Geocaching Live > Remove Live Data.
3 Select . Live geocaching data is removed from the device and no
longer appears in the geocache list.
Saving a Custom Geocache Filter
You can create and save custom filters for geocaches based on Removing Your Device Registration From
specific factors.
Geocaching.com
1 From the app drawer, select Setup > Geocaching > Filter If you transfer ownership of your device, you can remove your
Setup > Create Filter.
device registration from the geocaching website.
2 Select items to filter. From the app drawer, select Setup > Geocaching >
3 Select . Geocaching Live > Unregister Device.
By default, the new filter is saved automatically as Filter
followed by a number. For example, Filter 2. You can edit the
geocache filter to change the name (Editing a Custom Activities
Geocache Filter, page 7). Your device can be used for indoor, outdoor, athletic, and fitness
Editing a Custom Geocache Filter activities. When you start an activity, the device displays and
records sensor data. You can save activities and share them
1 From the app drawer, select Setup > Geocaching > Filter
Setup. with the Garmin Connect community.
You can also add Connect IQ activities and apps to your device
2 Select a filter.
using the Connect IQ Mobile app (Connect IQ Features,
3 Select an item to edit. page 5).
Applying a Custom Filter to a Geocache List When you are using an activity and you change some settings,
After you create a filter, you can apply it to the geocache list. such as data fields or units of measurement, the changes are
saved automatically as part of the activity. These settings are
1 From the app drawer, select Geocaching > > . loaded automatically the next time you switch the device to this
2 Select a filter. activity.
Your device includes several preloaded activities with settings
Downloading Geocaches Using a Computer configured for that activity. You can customize the settings for
You can load geocaches manually onto your device using a each preloaded activity, and you can create new custom
computer (Transferring Files to Your Device, page 18). You activities.
can place the geocache files into a GPX file and import them
into the GPX folder on the device. With a premium membership Recording an Activity
to geocaching.com, you can use the "pocket query" feature to By default, the device begins a recreational activity automatically
load a large group of geocaches onto your device as a single when you turn it on.
GPX file.
1 Connect the device to your computer using a USB cable.

Activities 7
1 Select an option: • To record activities at a specified time, select Time.
• To record the default recreational activity that began 5 Select Interval.
automatically when you turned on the device, proceed to 6 Complete an action:
step 4.
• If you selected Auto for the Record Method, select an
• To record a different activity type, proceed to step 2. option to record activities more or less often.
2 From the app drawer, select Activity Change. NOTE: Using the Most Often interval provides the most
3 Select the activity name. activity detail, but fills up the device memory quicker.
4 Begin your activity. • If you selected Distance or Time for the Record Method,
5 After you complete your activity, select Current Activity from enter a value, and select .
the app drawer.
6 Select . Pausing an Activity
1 From the app drawer, select Current Activity.
7 Select an option:
2 Select .
• To continue your activity, select .
• To save your activity, select . Saving the Current Activity
• To delete your activity, select . 1 From the app drawer, select Current Activity.
2 Select .
Creating a New Activity
If none of the preloaded activities fit the needs of your activity or 3 Select the date and time field to rename the saved activity
(optional).
trip, you can create a custom activity with its own unique
settings and data fields. 4 Select to save the activity.
1 From the app drawer, select Setup > Activities > Create
Activity. Clearing the Current Activity
2 Customize your settings and data fields. You can delete all recorded activity data since the start of the
activity.
Editing an Activity Name 1 From the app drawer, select Current Activity.
You can customize the name of an activity.
2 Select > Clear.
1 From the app drawer, select Setup > Activities.
2 Select an activity. Deleting an Activity History
3 Select Edit Name. 1 From the app drawer, select Activity History.
4 Enter the new name. 2 Select an activity.
Editing an Activity Icon 3 Select > Delete.
You can customize the icon displayed on an activity page.
Viewing Activity Information
1 From the app drawer, select Setup > Activities.
1 From the app drawer, select Activity History.
2 Select an activity.
2 Select an activity.
3 Select Edit Icon.
3 Select .
4 Select an icon. The beginning and the end of the trail are marked by flags.
Deleting an Activity 4 Select the information bar at the top of the screen.
Information about the activity appears.
NOTE: You cannot delete an activity while it is in use.
1 From the app drawer, select Setup > Activities. Viewing the Elevation Plot of an Activity
2 Select an activity. 1 From the app drawer, select Activity History.
3 Select Delete. 2 Select an activity.
3 Select .
Customizing Your Activity Log
You can customize how your device displays and records Saving a Location on an Activity
activities.
1 From the app drawer, select Activity History.
1 From the app drawer, select Activity History > Current
Activity > . 2 Select an activity.
2 Select an option: 3 Select .
• To change the color of the activity line on the map, select 4 Select a location on the activity.
Color. 5 Select the location information at the top of the map.
• To display a line on the map indicating your activity, select Information about the location appears.
Show On Map. 6 Select > OK.
3 Select > Setup Activities > Record Method.
4 Select an option: Opening Track Manager
• To record activities at a variable rate that creates an You can customize, use, and archive tracks using the track
optimum representation of your activities, select Auto. manager.
• To record activities at a specified distance, select From the app drawer, select Track Manager.
Distance.

8 Activities
 Navigation 2 Select the country or state, if necessary.
3 Enter the city or postal code.
You can navigate routes and tracks to a waypoint, geocache, or
any saved location in the device. You can also navigate to NOTE: Not all map data provides postal code searching.
photos taken on the device or stored photos with location 4 Select the city.
information. You can use the map or the compass to navigate to 5 Enter the house number.
your destination.
6 Enter the street.
Navigating to a Destination
1 If necessary, select the activity to use while navigating
Navigating with the Compass
(Recording an Activity, page 7). When navigating to a destination, points to your destination,
regardless of the direction you are moving.
2 From the main menu, select Where To?.
1 Begin navigating to a destination (Navigating to a
3 Select a category. Destination, page 9).
4 Select a destination. 2 From the app drawer, select Compass.
5 Select Go. 3 Turn until points toward the top of the compass, and
The map opens and your route is marked with a magenta continue moving in that direction to the destination.
line.
Calibrating the Compass
6 Navigate using the map (Navigating with the Map, page 9)
or compass (Navigating with the Compass, page 9). NOTICE
Finding a Location Near Another Location Calibrate the electronic compass outdoors. To improve heading
accuracy, do not stand near objects that influence magnetic
1 If necessary, select the activity to use while navigating fields, such as vehicles, buildings, and overhead power lines.
(Recording an Activity, page 7).
2 From the main menu, select Where To?. Your device was already calibrated at the factory, and the
3 Select > Search Near. device uses automatic calibration by default. If you experience
irregular compass behavior, for example, after moving long
4 Select a criteria to center your search, such as A Waypoint. distances or after extreme temperature changes, you can
5 Select a location. manually calibrate the compass.
Stopping Navigation 1 From the app drawer, select Compass.
From the map or compass, select > Stop Navigation. 2 Select > Calibrate Compass > Start.
3 Follow the on-screen instructions.
Navigating with the Map Course Pointer
1 Begin navigating to a destination (Navigating to a The course pointer is most useful when you are navigating to
Destination, page 9).
your destination in a straight line, such as when you are
2 From the main menu, select Map. navigating on water. It can help you navigate back to the course
A blue triangle represents your location on the map. As you line when you go off-course to avoid obstacles or hazards.
travel, the blue triangle moves and leaves a track log (trail). To enable the course pointer, from the app drawer, select Setup
3 Complete one or more actions: > Heading > Go To Line (Pointer) > Course (CDI).
• Select , and drag the map to view different areas.
• Select and to zoom in and out of the map.
• Select a location on the map (represented by a pin), and
select the information bar at the top of the screen to view
information about the selected location.

Navigating Using TracBack ®

While navigating, you can navigate back to the beginning of your

activity. This can be helpful when finding your way back to camp
or the trail head. Course line pointer. Indicates the direction of the desired course
line from your starting point to your next waypoint.
1 From the app drawer, select Activity History > Current
Activity > > TracBack. Course deviation indicator (CDI). Indicates the location of the
desired course line in relation to your location. If the CDI is aligned
The map displays your route with a magenta line, start point, with the course line pointer, you are on course.
and end point.
Course deviation distance. The dots indicate your distance off
2 Navigate using the map or the compass. course. The distance represented by each dot is indicated by the
scale in the upper-right corner.
Optional Maps To-and-from indicator. Indicates whether you are headed to or from
You can use additional maps with the device, such as BirdsEye the next waypoint.
satellite imagery, BlueChart g2, and City Navigator detailed
® ®

maps. Detailed maps may contain additional points of interest, Navigating with Sight 'N Go
such as restaurants or marine services. For more information, You can point the device at an object in the distance with the
go to http://buy.garmin.com or contact your Garmin dealer. compass direction locked in, project the object as a waypoint,
Finding an Address and navigate using the object as a reference point.
You can use optional City Navigator maps to search for 1 From the app drawer, select Sight 'N Go.
addresses (Optional Maps, page 9). 2 Point the device at an object.
1 From the main menu, select Where To? > Addresses.
Navigation 9
3 Select Lock Direction > Set Course. • Select Select Symbol to search using the symbol of the
4 Navigate using the compass. waypoint.
• Select Search Near to search near a recently found
Elevation Plot location, another waypoint, your current location, or a
By default, the elevation plot displays the elevation over the point on the map.
distance traveled. The top chart displays the full track, and the • Select Sort to view the list of waypoints based on nearest
bottom chart can display a portion of the track. You can touch distance or alphabetical order.
any point on either chart to view details about that point. You 4 Select a waypoint from the list.
can customize the elevation settings (Altimeter Settings,
page 15). Editing a Waypoint
Navigating to a Point on the Elevation Plot 1 From the app drawer, select Waypoint Manager.
1 From the app drawer, select Altimeter. 2 Select a saved waypoint.
2 Select an individual point on the plot. 3 Select an item to edit, such as the name.
3 Select . 4 Enter the new information, and select .
4 Select View Map.
5 Navigate using the map (Navigating with the Map, page 9) or Deleting a Waypoint
compass (Navigating with the Compass, page 9). 1 From the app drawer, select Waypoint Manager.
Changing the Plot Type 2 Select a waypoint.
You can change the elevation plot to display pressure and 3 Select > Delete.
elevation over time or distance.
1 From the app drawer, select Altimeter. Increasing the Accuracy of a Waypoint
2 Select > Altimeter Setup > Plot Type. Location
You can refine the accuracy of a waypoint location by averaging
3 Select plot type. the location data. When averaging, the device takes several
Resetting the Elevation Plot GPS readings at the same location and uses the average value
1 From the app drawer, select Altimeter. to provide more accuracy.
2 Select > Reset > Clear Current Activity > Clear. 1 From the app drawer, select Waypoint Averaging.
2 Select a waypoint.
Calibrating the Barometric Altimeter
You can manually calibrate the barometric altimeter if you know
3 Move to the waypoint location.
the correct elevation or the correct barometric pressure. 4 Select Start.
1 Go to a location where the elevation or barometric pressure 5 Follow the on-screen instructions.
is known. 6 When the confidence status bar reaches 100%, select Save.
2 From the app drawer, select Altimeter. For best results, collect four to eight samples for the waypoint,
3 Select > Altimeter Setup > Calibrate Altimeter. waiting at least 90 minutes between samples.
4 Follow the on-screen instructions.
Projecting a Waypoint
You can save a new waypoint by projecting the distance and
Waypoints bearing from a saved waypoint to a new location.
Waypoints are locations you record and store in the device. For example, if you would like to navigate to a location you
Waypoints can mark where you are, where you are going, or observe on the other side of a river or stream, you can project a
where you have been. You can add details about the location, waypoint from your current location to the observed location,
such as name, elevation, and depth. then navigate to the new location after crossing the river or
stream at a more suitable location.
You can add a .gpx file that contains waypoints by transferring
the file to the GPX folder (Transferring Files to Your Device, 1 From the app drawer, select Waypoint Manager.
page 18). 2 Select a waypoint.
3 Select > Project Waypoint.
Marking Your Current Location as a 4 Enter the bearing, and select .
Waypoint 5 Select a unit of measure.
You can mark your current location as a waypoint.
6 Enter the distance, and select .
1 From the app drawer, select Mark Waypoint.
7 Select Save.
2 Select the symbol, the name, or the notes field to add details
about the waypoint (optional).
3 Select for more waypoint options (optional). Routes
4 Select Save. A route is a sequence of waypoints or locations that leads you to
your final destination.
Finding a Waypoint
1 From the app drawer, select Waypoint Manager. Creating a Route Using Route Planner
2 If necessary, select to narrow the search. A route can include many waypoints, and it should include at
least a starting point and one destination.
3 If necessary, select an option:
• Select Spell Search to search using the name of the 1 From the app drawer, select Route Planner > Create Route
> Select First Point.
waypoint.

10 Waypoints
2 Select a category. 3 Select Reverse Route.
3 Select the first point in the route.
4 Select Use. Viewing the Elevation Plot of a Route
The elevation plot displays the elevations for a route based on
5 Select Select Next Point to add additional points to the your route setting. If your device is configured for direct routing,
route. the elevation plot displays the straight-line elevations between
6 Select to save the route. route points. If your device is configured for on-road routing, the
elevation plot displays the elevations along the roads included in
Creating a Route Using the Map your route.
1 From the app drawer, select Route Planner > Create Route 1 From the app drawer, select Route Planner.
> Select First Point > Use Map. 2 Select a route.
2 Move the map to select a point. 3 Select Elevation Plot.
3 Select Use.
4 Move the map, and select additional points on the map to
add to the route (optional). Camera and Photos
5 Select . NOTE: This feature is available only for models that include a
camera.
Editing the Name of a Route When you take a photo, the geographic location is saved with
You can customize the name of a route to make it distinct. the photo information. You can navigate to the location.
1 From the app drawer, select Route Planner. To view photos, from the app drawer, select Photo Viewer.
2 Select a route.
Taking a Photo
3 Select Change Name.
1 From the app drawer, select Camera.
4 Enter the new name.
2 Turn the device horizontally or vertically to change the
orientation of the photo.
Editing a Route
3 If necessary, select to turn on the flash.
You can add, remove, or rearrange points on a route.
TIP: You can select Auto to use the flash only when the
1 From the app drawer, select Route Planner. camera detects a low light scene.
2 Select a route. 4 If necessary, use two fingers on the touchscreen to zoom in
3 Select Edit Route. or out.
4 Select a point. 5 Hold to focus and hold the device still.
5 Select an option: A white frame appears on the screen. The device focuses on
• To view the point on the map, select Review. the object inside of the frame. When the photo is in focus, the
frame turns green.
• To change the order of the points on the route, select
Move Up or Move Down. 6 Release to take a photo.
• To insert an additional point on the route, select Insert.
The additional point is inserted before the point you are Applications
editing.
• To remove the point from the route, select Remove. Sending and Receiving Data Wirelessly
6 Select to save the route. Before you can share data wirelessly, you must be within 3 m
(10 ft.) of a compatible device.
Viewing a Route on the Map Your device can send and receive data when paired with
another compatible device using Bluetooth or ANT+ wireless
®
1 From the app drawer, select Route Planner.
technology. You can share waypoints, geocaches, routes,
2 Select a route. tracks, photos, and custom maps.
3 Select View Map. 1 From the app drawer, select Share Wirelessly.
Deleting a Route 2 Select an option:
1 From the app drawer, select Route Planner. • Select Send, and select a type of data.
2 Select a route. • Select Receive to receive data from another device. The
other compatible device must be attempting to send data.
3 Select Delete Route.
3 Follow the on-screen instructions.
Viewing the Active Route
1 While navigating a route, from the app drawer, select Active
Setting a Proximity Alarm
Route. Proximity alarms alert you when you are within a specified range
of a particular location.
2 Select a point in the route to view additional details.
1 From the app drawer, select Proximity Alarms > Create
Alarm.
Reversing a Route
You can switch the start and end points of your route to navigate 2 Select a category.
the route in reverse. 3 Select a location.
1 From the app drawer, select Route Planner. 4 Select Use.
2 Select a route. 5 Enter a radius, and select .

Camera and Photos 11

When you enter an area with a proximity alarm, the device 1 From the app drawer, select Satellite > > Use With GPS
sounds a tone. Off.
TIP: You can configure separate alarm tones for when you enter 2 Select > Set Location On Map.
and leave an area. 3 Select a location.
4 Select Use.
Calculating the Size of an Area
1 From the app drawer, select Area Calculation > Start. Controlling a VIRB Action Camera
®

2 Walk around the perimeter of the area you want to calculate. Before you can use the VIRB remote function, you must enable
3 Select Calculate when finished. the remote control setting on your VIRB camera. For more
information, see the owner's manual for your VIRB camera.
Viewing the Calendar and Almanacs 1 Turn on your VIRB camera, and enable the remote control
You can view device activity, such as when a waypoint was setting.
saved. You can also view daily almanac information for the sun 2 On your device, from the app drawer, select VIRB Remote.
and moon, and hunting and fishing.
3 Wait while the device connects with your VIRB camera.
1 From the app drawer, select an option:
4 Select an option:
• To view device activity for specific days, select Calendar.
• To record video, drag the slider bar up.
• To view the sunrise, sunset, moonrise, and moonset
information, select Sun and Moon. • To take a photo, select .
• To view the predicted best times for hunting and fishing,
select Hunt and Fish.
Phone Notifications
This feature is not available for all device models.
2 If necessary, select or to view a different month.
Phone notifications require a compatible smartphone to be in
3 Select a day. range and paired with the device. When your phone receives
messages, it sends notifications to your device.
Setting an Alarm
1 From the app drawer, select Alarm Clock. Hiding Notifications
Notifications are enabled by default when you pair your device
2 Select and to set the time. with a compatible smartphone. You can hide notifications so
3 Select Turn Alarm On. they do not appear on your device screen.
4 Select an option. 1 From the app drawer, select Setup > Bluetooth.
The alarm sounds at the selected time. If the device is off at 2 If necessary, select Bluetooth if it is not turned on.
the alarm time, the device turns on and sounds the alarm. 3 Select Notifications to turn off notifications on the device.
Starting the Countdown Timer
1 From the app drawer, select Alarm Clock > > Timer. Fitness
2 Select and to set the time.
3 Select Start Timer. History
History includes date, time, distance, calories, average speed or
pace, ascent, descent, and optional ANT+ sensor information.
Opening the Stopwatch
From the app drawer, select Stopwatch. NOTE: History is not recorded while the timer is stopped or
paused.
Satellite Page When the device memory is full, a message appears. The
device does not automatically delete or overwrite your history.
The satellite page shows your current location, GPS accuracy,
You can upload your history to Garmin Connect (Using Garmin
satellite locations, and signal strength.
Connect, page 12) periodically to keep track of all your activity
Changing the Satellite View data.
1 From the app drawer, select Satellite. Viewing an Activity History
2 Select . From the history, you can view details about a previous activity.
3 Select an option: 1 From the app drawer, select Activity History.
• To orient the satellite view with your current track toward 2 Select an activity.
the top of the screen, select Track Up.
• To show a unique color for each satellite and its signal Deleting an Activity from Your History
strength bar, select Multicolor. 1 From the app drawer, select Activity History.
2 Select an activity.
Turning Off GPS
You can turn off GPS on your device to stop tracking your 3 Select > Delete.
location. Using Garmin Connect
1 From the app drawer, select Satellite. 1 Connect the device to your computer using the USB cable.
2 Select > Use With GPS Off. 2 Go to www.garminconnect.com/start.
Simulating a Location 3 Follow the on-screen instructions.
You can use the device with GPS off to perform maintenance on Optional Fitness Accessories
waypoints and routes, or to conserve battery life. You can set You can use optional fitness accessories including a heart rate
the location manually to view your current location on the map. monitor or a cadence sensor with your device. These

12 Fitness
accessories use ANT+ wireless technology to send data to the The maximum heart rate for each zone is based on the
device. minimum heart rate of the previous zone. For example, if you
Before you can use the fitness accessory with your device, you enter 167 as a minimum heart rate for zone 5, the device
must install the accessory according to the instructions included uses 166 as the maximum rate for zone 4.
with the accessory. 3 Enter your minimum heart rate for zones 4-1.
Pairing Your ANT+ Sensors
Before you can pair, you must put on the heart rate monitor or
install the sensor.
Customizing the Device
Pairing is the connecting of ANT+ wireless sensors, for example, Adjusting the Backlight Brightness
connecting a heart rate monitor with your device.
You can adjust the backlight brightness to maximize the battery
1 Bring the device within 3 m (10 ft.) of the sensor. life. For a longer battery life, you should turn off the backlight
NOTE: Stay 10 m (30 ft.) away from other ANT+ sensors when using the device in daylight.
while pairing. 1 Swipe down from the top of the screen.
2 From the app drawer, select Setup > ANT Sensor. 2 Select or .
3 Select your sensor.
4 Select Search for New. Customizing the Keys
When the sensor is paired with your device, the sensor status You can customize some device key actions to provide quick
changes from Searching to Connected. access to menus, settings, apps, or other device functions.
Tips for Pairing ANT+ Accessories with Your Garmin Device 1 From the app drawer, select Setup > System > Configure
Keys.
• Verify that the ANT+ accessory is compatible with your
Garmin device. 2 Select Power Key or Call Key.
• Before you pair the ANT+ accessory with your Garmin 3 Select Single Tap, Double Tap, or Hold.
device, move 10 m (32.9 ft.) away from other ANT+ 4 Select an option.
accessories.
• Bring the Garmin device within range 3 m (10 ft.) of the ANT+ Customizing the Main Menu
accessory. You can change the layout of the main menu.
• After you pair the first time, your Garmin device automatically 1 From the app drawer, select Setup > Main Menu.
recognizes the ANT+ accessory each time it is activated. This
process occurs automatically when you turn on the Garmin 2 Select an option:
device and only takes a few seconds when the accessories • To switch to a different page of the main menu, select
are activated and functioning correctly. and .
• When paired, your Garmin device receives data from only • To change the number of items on a main menu page,
your accessory, and you can go near other accessories. select and .
• To set the current page of the main menu as the starting
About Heart Rate Zones page, select > Set as Start Page.
Many athletes use heart rate zones to measure and increase Changing Items on the Main Menu
their cardiovascular strength and improve their level of fitness. A
You can add, remove, and change the order of items on the
heart rate zone is a set range of heartbeats per minute. The five
main menu.
commonly accepted heart rate zones are numbered from 1 to 5
according to increasing intensity. Generally, heart rate zones are 1 From the app drawer, select Setup > Main Menu.
calculated based on percentages of your maximum heart rate. 2 If necessary, increase the number of items on the main
menu, or switch to a different page of the main menu
Fitness Goals (Customizing the Dashboard on the Main Menu, page 13).
Knowing your heart rate zones can help you measure and
improve your fitness by understanding and applying these 3 Select an option:
principles. • To add an item to the main menu, select Add Item Here,
• Your heart rate is a good measure of exercise intensity. and select an item.
• Training in certain heart rate zones can help you improve • To move an item on the main menu, select the item, and
cardiovascular capacity and strength. select Move Item Here.
If you know your maximum heart rate, you can use the table • To delete an item on the main menu, select the item, and
(Heart Rate Zone Calculations, page 22) to determine the best select .
heart rate zone for your fitness objectives. Customizing the Dashboard on the Main Menu
If you do not know your maximum heart rate, use one of the By default, radio information appears in the dashboard on the
calculators available on the Internet. Some gyms and health main menu. You can change the information shown in this
centers can provide a test that measures maximum heart rate. dashboard.
The default maximum heart rate is 220 minus your age.
1 From the app drawer, select Setup > Main Menu.
Setting Your Heart Rate Zones 2 Select > Change Dashboards.
Before the device can determine your heart rate zones, you 3 Select a dashboard.
must set up your fitness user profile (Setting Your Fitness User
Profile, page 16).
Customizing the App Drawer
You can manually adjust the heart rate zones according to your You can add, remove, and change the order of items in the app
fitness goals (Fitness Goals, page 13). drawer.
1 From the app drawer, select Setup > Fitness > HR Zones. 1 From the app drawer, select Setup > Main Menu > >
2 Enter the maximum and minimum heart rate for zone 5. Setup Drawer.

Customizing the Device 13

2 Select an option: Setting the Touchscreen Sensitivity
• To add an item to the app drawer, select Add and select You can adjust the touchscreen sensitivity to suit your activity.
an item. 1 From the app drawer, select Setup > Accessibility > Touch
• To move an item in the app drawer, select the item, and Sensitivity.
select another item to switch positions. 2 Select an option.
• To delete an item from the app drawer, select the item, TIP: You can test the touchscreen settings with and without
and select . gloves based on your activity.
NOTE: Some items cannot be deleted from the app
drawer. Display Settings
From the app drawer, select Setup > Display.
Adding a Shortcut to the Main Menu Backlight Timeout: Sets the length of time before the backlight
You can add shortcuts to the application drawer, or to the main turns off.
menu or favorites dashboard when the device is in classic
mode. You can create shortcuts to enable the device to perform Orientation Lock: Locks the screen orientation in portrait or
multiple actions simultaneously. If the shortcut does not appear landscape mode, or allows the screen to change orientation
in the list, you can create it (Creating a Shortcut, page 14). automatically based on the device orientation.
1 From the app drawer, select Setup > Shortcuts. Screen Capture: Allows you to save the image on the device
screen.
2 Select the shortcut.
Battery Save: Saves the battery power and prolongs the battery
3 Select Add to Menu. life by turning off the screen when the backlight times out
4 Select Main Menu, Drawer, or Favorites. (Turning On Battery Save Mode, page 2).
Creating a Shortcut
Configuring the Maps
1 From the app drawer, select Setup > Shortcuts > Create
Shortcut. You can enable or disable the maps currently loaded on the
device.
2 Select Name, and enter a name.
From the app drawer, select Setup > Map > Configure
3 Select Icon, and select an icon. Maps.
4 Select an option:
Map Settings
• To add a shortcut to a specific device setting, select From the app drawer, select Setup > Map.
Setup.
Orientation: Adjusts how the map is shown on the page. The
• To add a shortcut that begins navigation to a specific North Up option shows north at the top of the page. The
waypoint, select Where To?. Track Up option shows your current direction of travel toward
• To add a shortcut to a specific application, select the top of the page. The Automotive Mode option shows an
Application. automotive perspective with the direction of travel at the top.
• To allow a shortcut to quickly change your activity, select Dashboard: Sets a dashboard to display on the map. Each
Activity. dashboard shows different information about your route or
your location.
Custom Data Fields and Dashboards Guidance Text: Sets when the guidance text is shown on the
Data fields display information about your location or other map.
specified data. Dashboards are a custom grouping of data that
can be helpful to a specific or general task, such as geocaching. Advanced Map Settings
From the app drawer, select Setup > Map > Advanced Setup.
Enabling the Map Data Fields Detail: Sets the amount of detail shown on the map. Showing
You can show custom data fields on the map. more detail may cause the map to redraw more slowly.
1 From the map, select > Setup Map > Dashboard. Map Speed: Adjusts the speed at which the map is drawn. A
2 Select Large Data Field or Small Data Fields. faster map drawing speed decreases the battery life.
3 If necessary, on the map, select at the top of the screen to Shaded Relief: Shows detail relief on the map (if available) or
show the data fields. turns off shading.
Customizing the Data Fields Vehicle: Sets the position icon, which represents your position
the map. The default icon is a small blue triangle.
Before you can change the map data fields, you must enable
them (Enabling the Map Data Fields, page 14). Zoom Controls: Sets the auto zoom and the location of the
buttons in portrait or landscape mode (Zoom Controls
You can customize the data fields and dashboards of the map,
Settings, page 14).
compass, trip computer, elevation plot, and status pages.
Text Size: Sets the text size for map items.
1 From a page that displays data fields, select a data field.
2 Select a data field category and a data field. Zoom Controls Settings
From the app drawer, select Setup > Map > Advanced Setup >
Customizing Dashboards Zoom Controls.
1 Select a page. Auto Zoom: Automatically selects the zoom level for optimal
2 Select an option: use of your map. When disabled, you must zoom in or out
• From the map, select > Setup Map > Dashboard. manually.
• From the compass or trip computer, select > Change Portrait Buttons: Sets the location of the zoom buttons when in
Dashboard. portrait mode.
3 Select a dashboard. Landscape Buttons: Sets the location of the zoom buttons
when in landscape mode.

14 Customizing the Device

Zoom Levels: Adjusts the zoom level at which map items Activity: Sets an activity used for transportation while routing.
appear. The map items do not appear when the map zoom The device calculates routes optimized for the type of activity
level is higher than the selected level. you are doing.
Calculation Method: Sets the method used to calculate your
System Settings route.
From the app drawer, select Setup > System. Lock On Road: Locks the blue triangle, which represents your
Satellite: Allows you to adjust the satellite system settings position on the map, onto the nearest road. This is most
(Satellite Settings, page 15). useful when driving or navigating on roads.
Text Language: Sets the text language on the device. Off Route Recalculation: Sets recalculation preferences when
NOTE: Changing the text language does not change the navigating away from an active route.
language of user-entered data or map data. Avoidance Setup: Sets the types of roads, terrain, and
Interface: Sets the communication interface mode to Garmin transportation methods to avoid while navigating.
Spanner, Garmin Serial, NMEA In/Out, Text Out, RTCM, or Route Transitions: Sets how the device routes from one point
MTP. on the route to the next. This setting is available only for
Configure Keys: Sets the power key or user key as a shortcut some activities. The Distance option routes you to the next
to a menu, setting, or application. point on the route when you are within a specified distance of
your current point.
Mode: Sets the main menu to look like a classic outdoor
handheld device main menu or an activity-based main menu.
Heading Settings
NOTE: This device is set to Classic by default. Changing this You can customize the compass settings.
setting to Activity significantly alters the user interface, radio
features, and activity recording features. From the app drawer, select Setup > Heading.
Battery Type: Sets the battery type for the device. Display: Sets the type of directional heading shown on the
compass.
NOTE: This setting only appears when the optional AA
battery pack is installed. North Reference: Sets the north reference used on the
compass.
Satellite Settings Go To Line (Pointer): Allows you to use the bearing pointer that
From the app drawer, select Setup > System > Satellite. points in the direction of your destination, or use the course
Satellite System: Allows you to set the satellite system to GPS, pointer that shows your relationship to the course line leading
GPS + GLONASS (GPS and GLONASS, page 15), or to the destination.
Demo Mode (GPS off). Compass: Automatically switches from an electronic compass
WAAS/EGNOS: Sets the satellite system to Wide Area to a GPS compass when you are traveling at a higher rate of
Augmentation System/European Geostationary Navigation speed for a period of time.
Overlay Service (WAAS/EGNOS). For more information Calibrate Compass: Allows you to calibrate the compass if you
about WAAS, go to www.garmin.com/aboutGPS/waas.html. experience irregular compass behavior, for example, after
moving long distances or after extreme temperature changes
GPS and GLONASS
(Calibrating the Compass, page 9).
The default satellite system setting is GPS + GLONASS, which
offers increased performance in challenging environments and
faster position acquisition. Using GPS and GLONASS can Altimeter Settings
reduce battery life more quickly than using GPS only. From the app drawer, select Setup > Altimeter.
Auto Calibration: Automatically calibrates the altimeter each
Appearance Settings time an activity is started. The device continues to
From the app drawer, select Setup > Appearance. automatically calibrate the altimeter as long as the device
receives GPS signals and auto calibrate continuous is on.
Mode: Sets a light background, a dark background, or
automatically switches between the two based on the sunrise Barometer Mode: Variable Elevation allows the barometer to
and sunset time for your current location. measure changes in elevation while you are moving. Fixed
Elevation assumes the device is stationary at a fixed
Day Color: Sets the color for the selections made when in day elevation, so the barometric pressure should only change
mode. due to weather.
Night Color: Sets the color for the selections made when in Pressure Trending: Sets how the device records pressure
night mode. data. Save Always can be useful when you are watching for
Landscape Controls: Places the controls on the left or right pressure fronts.
side of the screen when in landscape mode. Plot Type: Allows you to view elevation changes over a period
of time or distance, barometric pressure over a period of
Setting the Device Tones time, or ambient pressure changes over a period of time.
You can customize tones for messages, keys, turn warnings, Calibrate Altimeter: Allows you to calibrate the barometric
and alarms. altimeter when you know the correct elevation or the correct
1 From the app drawer, select Setup > Tones > Tones > On. barometric pressure (Calibrating the Barometric Altimeter,
2 Select a tone for each audible type. page 10).

Routing Settings Position Format Settings

The available routing settings vary based on the activity NOTE: You should not change the position format or the map
selected. datum coordinate system unless you are using a map or chart
that specifies a different position format.
From the app drawer, select Setup > Routing.
From the app drawer, select Setup > Position Format.

Customizing the Device 15

Position Format: Sets the position format in which a location Marking Laps by Distance
reading appears. You can use the Auto Lap feature to automatically mark the lap
®

Map Datum: Sets the coordinate system on which the map is at a specific distance. This feature is helpful for comparing your
structured. performance over different parts of an activity.
Map Spheroid: Shows the coordinate system the device is 1 From the app drawer, select Setup > Fitness > Auto Lap.
using. The default coordinate system is WGS 84. 2 Enter a value, and select .
Changing the Units of Measure Marine Settings
You can customize units of measure for distance and speed, From the app drawer, select Setup > Marine.
elevation, depth, temperature, pressure, and vertical speed.
Marine Chart Mode: Sets the type of chart the device uses
1 From the app drawer, select Setup > Units. when displaying marine data. Nautical displays various map
2 Select a measurement type. features in different colors so the marine POIs are more
3 Select a unit of measure. readable and so the map reflects the drawing scheme of
paper charts. Fishing (requires marine maps) displays a
detailed view of bottom contours and depth soundings and
Time Settings simplifies map presentation for optimal use while fishing.
From the app drawer, select Setup > Time.
Appearance: Sets the appearance of marine navigation aids on
Time Format: Sets the device to show time in a 12-hour or 24- the map.
hour format.
Marine Alarm Setup: Sets alarms for when you exceed a
Time Zone: Sets the time zone for the device. Automatic sets specified drift distance while anchored, when you are off
the time zone automatically based on your GPS position. course by a specified distance, and when you enter water of
a specific depth.
Geocaching Settings
From the app drawer, select Setup > Geocaching. Setting Up Marine Alarms
Geocaching Live: Sets the device to display or hide live 1 From the app drawer, select Setup > Marine > Marine
geocache data. Alarm Setup.
Geocache Style: Sets the device to display the geocache list 2 Select an alarm type.
using names or codes. 3 Select On.
chirp Searching: Allows the device to search for a geocache 4 Enter a distance, and select .
containing a chirp accessory (Enabling chirp Searching,
page 7). Resetting Data and Settings
Program chirp: Programs the chirp accessory. See the chirp You can reset trip data, delete all waypoints, clear the current
Owner's Manual at www.garmin.com. track, or restore default values.
Filter Setup: Allows you to create and save custom filters for 1 From the app drawer, select Setup > Reset.
geocaches (Saving a Custom Geocache Filter, page 7). 2 Select an option:
Found Geocaches: Allows you to edit the number of geocaches • To reset data specific to a trip, such as distance and
found. This number automatically increases when you log a averages, select Reset Trip Data.
find (Logging the Attempt, page 6).
• To delete all saved waypoints, select Delete All
Waypoints.
ANT+ Sensor Settings • To clear the data recorded since you started your current
For more information about optional fitness accessories, see activity, select Clear Current Activity.
Optional Fitness Accessories, page 12.
NOTE: The device continues to record new data for the
current activity.
Fitness Settings
• To reset the settings for your current activity type to the
From the app drawer, select Setup > Fitness.
factory default values, select Reset Activity Settings.
Auto Lap: Sets the device to automatically mark the lap at a
specific distance. • To restore all device settings to the factory default values,
select Reset All Settings.
Activity Type: Sets the fitness activity to hiking, running,
cycling, and more. This allows your activity to appear as the NOTE: Resetting all settings clears all geocaching activity
correct type when you transfer it to Garmin Connect. from your device.
User: Sets the user profile information (Setting Your Fitness Restoring Default Values for Specific Settings
User Profile, page 16). You can restore the default values for specific settings
HR Zones: Sets the five heart rate zones for fitness activities. categories.
Setting Your Fitness User Profile 1 From the app drawer, select Setup.
The device uses information that you enter about yourself to 2 Select a category to restore.
calculate accurate data. You can modify user profile information 3 Select > Restore Defaults.
such as gender, age, weight, height, and lifetime athlete (About
Lifetime Athletes, page 16). Restoring Default Values for Specific Page Settings
1 From the app drawer, select Setup > Fitness > User. You can restore the default values for settings for the map,
compass, trip computer, and elevation plot.
2 Modify the settings.
1 Open the page for which you will restore the settings.
About Lifetime Athletes
2 Select > Restore Defaults.
A lifetime athlete is an individual who has trained intensely for
many years (with the exception of minor injuries) and has a
resting heart rate of 60 beats per minute (bpm) or less.

16 Customizing the Device

 Device Information Avoid extreme shock and harsh treatment, because it can
degrade the life of the product.
Attaching the Carabiner Clip Cleaning the Device
1 Position the carabiner clip in the slots on the mounting 1 Wipe the device using a cloth dampened with a mild
spine of the device. detergent solution.
2 Wipe it dry.
After cleaning, allow the device to dry completely.
Cleaning the Touchscreen
1 Use a soft, clean, lint-free cloth.
2 If necessary, lightly dampen the cloth with water.
3 If using a dampened cloth, turn off the device and disconnect
the device from power.
2 Slide the carabiner clip up until it locks in place. 4 Gently wipe the screen with the cloth.
Headsets and Microphones Water Immersion
This device is compatible with many headset and microphone NOTICE
accessories that connect using a 2.5 mm jack (Device Overview,
The device is water resistant to IEC Standard 60529 IPX7. It can
page 1).
withstand immersion in 1 meter of water for 30 minutes.
By default, the device is set to detect automatically when a new Prolonged submersion can cause damage to the device. After
headset or microphone is connected. submersion, be certain to wipe dry and air dry the device before
NOTE: When connecting a headset with a push to talk (PTT) using or charging.
button, you must press the PTT button after connecting the
headset for the device to detect the headset. Data Management
This device is compatible with Voice Operated Transmission NOTE: The device is not compatible with Windows 95, 98, Me,
®

(VOX) devices. These accessories allow you to use the device Windows NT , and Mac OS 10.3 and earlier.
® ®

hands-free by transmitting automatically when a voice is

detected. You can adjust the sensitivity level of connected VOX File Types
devices (Advanced Radio Setup, page 5). The handheld device supports these file types:
• Files from BaseCamp™ or HomePort™. Go to
Product Updates www.garmin.com/trip_planning.
On your computer, install Garmin Express™ (www.garmin.com • GPX route, track, and waypoint files.
/express). On your smartphone, install the Garmin Connect
Mobile app. • GPX geocache files (Downloading Geocaches Using a
Computer, page 7).
This provides easy access to these services for Garmin devices:
• JPEG photo files.
• Software updates
• GPI custom POI files from the Garmin POI Loader. Go to
• Map updates www.garmin.com/products/poiloader.
• Data uploads to Garmin Connect • FIT files for exporting to Garmin Connect.
• Product registration
Installing a Memory Card
Maximizing Battery Life You can install a microSD memory card for additional storage or
pre-loaded maps.
You can do several things to extend the life of the batteries.
• Reduce the backlight brightness (Adjusting the Backlight
1 Turn the D-ring counter-clockwise, and pull up to remove the
battery pack.
Brightness, page 13).
• Reduce the backlight timeout (Display Settings, page 14).
2 In the battery compartment, slide the card holder toward the
top of the device, and lift up.
• Use battery save mode (Turning On Battery Save Mode,
page 2).
• Decrease the map drawing speed (Configuring the Maps,
page 14).
• Turn off GLONASS (GPS and GLONASS, page 15).

Device Care
NOTICE
Do not store the device where prolonged exposure to extreme
temperatures can occur, because it can cause permanent
damage. 3 Place the memory card with the contacts facing down.
Never use a hard or sharp object to operate the touchscreen, or 4 Close the card holder.
damage may result.
5 Slide the card holder toward the bottom of the device to lock
Avoid chemical cleaners, solvents, and insect repellents that can it.
damage plastic components and finishes.
6 Replace the battery pack, and turn the D-ring clockwise.
Secure the weather cap tightly to prevent damage to the USB
port.

Device Information 17
Connecting the Device to Your Computer Specifications
NOTICE Battery type Lithium-ion battery pack or four AA batteries
(NiMH, alkaline, or lithium)
To prevent corrosion, thoroughly dry the USB port, the weather
cap, and the surrounding area before charging or connecting to Battery life Lithium-ion battery pack: up to 14 hours of
a computer. typical usage.
AA batteries: up to 18 hours of typical usage.
1 Pull up the weather cap from the USB port. Water rating IEC 60529 IPX71
2 Plug the small end of the USB cable into the USB port on the Operating From -20º to 55ºC (from -4º to 131ºF)
device. temperature range
3 Plug the large end of the USB cable into a computer USB Charging From 0º to 40°C (from 32º to 104°F)
port. temperature range
Your device and memory card (optional) appear as Communication 2.4 GHz ANT+ wireless communications
removable drives in My Computer on Windows computers frequency/protocol protocol
and as mounted volumes on Mac computers. Bluetooth enabled device
Radio channels 1 through 22: GMRS channels (requires FCC
Transferring Files to Your Device license in the United States)
1 Connect the device to your computer. 15R through 22R: GMRS repeater channels
(requires FCC license in the United States)
On Windows computers, the device appears as a removable
(position reporting is not allowed by the FCC on
drive or a portable device, and the memory card may appear repeater channels)
as a second removable drive. On Mac computers, the device Channels WX 1 through 7: weather radio
and memory card appear as mounted volumes. channels
NOTE: Some computers with multiple network drives may not Radio output power GMRS: 0.5, 2.0, or 5.0 W (5.0 W is available
display device drives properly. See your operating system only in the United States, and only when using
documentation to learn how to map the drive. the lithium-ion battery pack. )
2 On your computer, open the file browser.
3 Select a file. Radio Frequency Charts
4 Select Edit > Copy. GMRS Radio Frequencies
5 Open the portable device, drive, or volume for the device or Rino models sold in the United States and Canada use these
memory card. frequencies.
6 Browse to a folder. NOTE: If you plan to use this device in countries outside of the
United States or Canada, you should check with the government
7 Select Edit > Paste. of that country for any restrictions on GMRS use.
The file appears in the list of files in the device memory or on Channel Transmit Receive Channel Description
the memory card. Number Frequency Frequency
(MHz) (MHz)
Deleting Files
1 462.5625 462.5625 GMRS Interstitial 1
NOTICE 2 462.5875 462.5875 GMRS Interstitial 2
If you do not know the purpose of a file, do not delete it. Your 3 462.6125 462.6125 GMRS Interstitial 3
device memory contains important system files that should not
4 462.6375 462.6375 GMRS Interstitial 4
be deleted.
5 462.6625 462.6625 GMRS Interstitial 5
1 Open the Garmin drive or volume. 6 462.6875 462.6875 GMRS Interstitial 6
2 If necessary, open a folder or volume. 7 462.7125 462.7125 GMRS Interstitial 7
3 Select a file. 8 467.5625 467.5625 GMRS Primary 1
4 Press the Delete key on your keyboard. 9 467.5875 467.5875 GMRS Primary 2
NOTE: If you are using an Apple computer, you must empty
®
10 467.6125 467.6125 GMRS Primary 3
the Trash folder to completely remove the files. 11 467.6375 467.6375 GMRS Primary 4
12 467.6625 467.6625 GMRS Primary 5
Disconnecting the USB Cable
If your device is connected to your computer as a removable 13 467.6875 467.6875 GMRS Primary 6
drive or volume, you must safely disconnect your device from 14 467.7125 467.7125 GMRS Primary 7
your computer to avoid data loss. If your device is connected to 15 462.5500 462.5500 GMRS Primary 8
your Windows computer as a portable device, it is not necessary 16 462.5750 462.5750 GMRS Primary 9
to safely disconnect the device.
17 462.6000 462.6000 GMRS Primary 10
1 Complete an action: 18 462.6250 462.6250 GMRS Primary 11
• For Windows computers, select the Safely Remove 19 462.6500 462.6500 GMRS Primary 12
Hardware icon in the system tray, and select your device.
20 462.6750 462.6750 GMRS Primary 13
• For Apple computers, select the device, and select File >
21 462.7000 462.7000 GMRS Primary 14
Eject.
22 462.7250 462.7250 GMRS Primary 15
2 Disconnect the cable from your computer.
15R 467.5500 462.5500 GMRS Repeater 1
16R 467.5750 462.5750 GMRS Repeater 2
17R 467.6000 462.6000 GMRS Repeater 3

1 The device withstands incidental exposure to water of up to 1 m for up to 30 min.

For more information, go to www.garmin.com/waterrating.

18 Device Information
Channel Transmit Receive Channel Description Channel Frequency (MHz) Channel Description
Number Frequency Frequency Number
(MHz) (MHz) 34 477.2500 Repeater input
18R 467.6250 462.6250 GMRS Repeater 4 35 477.2750 Emergency repeater input:
19R 467.6500 462.6500 GMRS Repeater 5 reserved
20R 467.6750 462.6750 GMRS Repeater 6 36 477.3000 Repeater input
21R 467.7000 462.7000 GMRS Repeater 7 37 477.3250 Repeater input
22R 467.7250 462.7250 GMRS Repeater 8 38 477.3500 Repeater input
39 477.3750 General chat channel
CBRS/PRS Radio Frequencies 40 477.4000 Road safety channel Australia
Rino models sold in Australia and New Zealand use these wide
frequencies. 41 476.4375 Repeater channel
NOTE: If you plan to use this device in countries outside of 42 476.4625 Repeater channel
Australia or New Zealand, you should check with the 43 476.4875 Repeater channel
government of that country for any restrictions on CBRS or PRS
use. 44 476.5125 Repeater channel
45 476.5375 Repeater channel
Channel Frequency (MHz) Channel Description
Number 46 476.5625 Repeater channel
1 476.4250 Repeater channel 47 476.5875 Repeater channel
2 476.4500 Repeater channel 48 476.6125 Repeater channel
3 476.4750 Repeater channel 49 476.6375 General chat channel
4 476.5000 Repeater channel 50 476.6625 General chat channel
5 476.5250 Emergency repeater channel: 51 476.6875 General chat channel
reserved 52 476.7125 General chat channel
6 476.5500 Repeater channel 53 476.7375 General chat channel
7 476.5750 Repeater channel 54 476.7625 General chat channel
8 476.6000 Repeater channel 55 476.7875 General chat channel
9 476.6250 General chat channel 56 476.8125 General chat channel
10 476.6500 4WD clubs or convoys and 57 476.8375 General chat channel
national parks
58 476.8625 General chat channel
11 476.6750 Call channel
59 476.8875 General chat channel
12 476.7000 General chat channel
60 476.9125 General chat channel
13 476.7250 General chat channel
61 N/A Reserved for future expansion
14 476.7500 General chat channel
62 N/A Reserved for future expansion
15 476.7750 General chat channel
63 N/A Reserved for future expansion
16 476.8000 General chat channel
64 477.0125 General chat channel
17 476.8250 General chat channel
65 477.0375 General chat channel
18 476.8500 Caravanners and campers
convoy channel 66 477.0625 General chat channel

19 476.8750 General chat channel 67 477.0875 General chat channel

20 476.9000 General chat channel 68 477.1125 General chat channel

21 476.9250 General chat channel 69 477.1375 General chat channel

22 476.9500 Telemetry and telecommand 70 477.1625 General chat channel

channel. GPS position data is 71 477.1875 Repeater input
transmitted on this channel, and 72 477.2125 Repeater input
audio transmissions are not
possible. 73 477.2375 Repeater input
23 476.9750 Telemetry and telecommand 74 477.2625 Repeater input
channel. GPS position data is 75 477.2875 Repeater input
transmitted on this channel, and 76 477.3125 Repeater input
audio transmissions are not
possible. 77 477.3375 Repeater input
24 477.0000 General chat channel 78 477.3625 Repeater input
25 477.0250 General chat channel 79 477.3875 General chat channel
26 477.0500 General chat channel 80 477.4125 General chat channel
27 477.0750 General chat channel
Weather Radio Frequencies
28 477.1000 General chat channel
Weather radio broadcasts are available in the United States
29 477.1250 Road safety channel: Pacify only.
Hwy/Mwy between Brisbane
(QLD) and Sydney (NSW) Channel Number Receive Frequency Channel Description
(MHz)
30 477.1500 General chat channel
WX 1 162.550 NOAA 1 (Weather radio)
31 477.1750 Repeater input
WX 2 162.400 NOAA 2 (Weather radio)
32 477.2000 Repeater input
WX 3 162.475 NOAA 3 (Weather radio)
33 477.2250 Repeater input

Device Information 19
Channel Number Receive Frequency Channel Description DCS Code DCS Code DCS Code
(MHz) 23 162 466
WX 4 162.425 NOAA 4 (Weather radio) 25 165 503
WX 5 162.450 NOAA 5 (Weather radio) 26 172 506
WX 6 162.500 NOAA 6 (Weather radio) 31 174 516
WX 7 162.525 NOAA 7 (Weather radio) 32 205 532
43 271 546
CTCSS Frequencies
47 306 565
CTCSS frequencies and squelch codes may differ in some
radios from third-party manufacturers. For the best results, you 51 311 606
should compare CTCSS frequency information from your third- 54 315 612
party radio with the information in this table. 65 331 624
Channel Number Frequency (MHz) 71 343 627
0 199.5 72 346 631
1 67.0 73 351 632
2 71.9 74 364 654
3 74.4 114 365 662
4 77.0 115 371 664
5 79.7 116 411 703
6 82.5 125 412 712
7 85.4 131 413 723
8 88.5 132 423 731
9 91.5 134 431 732
10 94.8 143 432 734
11 97.4 152 445 743
12 100.0 155 464 754
13 103.5 156 465
14 107.2
15 110.9 FCC Licensing Information
16 114.8 The Rino two-way radio operates on General Mobile Radio
17 118.8 Service (GMRS) frequencies regulated by the Federal
18 123.0 Communications Commission (FCC) in the United States.
Operation on the GMRS frequencies is subject to rules as
19 127.3
specified in 47 C.F.R. Part 95. In order to transmit on GMRS
20 131.8 frequencies, you are required to obtain a license from the FCC.
21 136.5 For more information on GMRS, FCC forms, and fees, go to the
22 141.3 FCC web page at www.fcc.gov/general-mobile-radio-service-
23 146.2
gmrs.
24 151.4 No license is required to operate on GMRS channels in Canada;
however, GMRS repeater channels are not approved for use by
25 156.7
the Canadian government.
26 162.2
For use in countries outside of the United States and Canada,
27 167.9 check with that government for any restrictions of GMRS use.
28 173.8
29 179.9 Viewing Device Information
30 186.2 You can view the unit ID, software version, regulatory
31 192.8 information, and license agreement.
32 203.5 From the app drawer, select Setup > About.
33 210.7
34 218.1 Troubleshooting
35 225.7
36 233.6 My handheld device is not responding
37 241.8 If your handheld device stops responding, you can reset the
38 250.3 device.
NOTE: This does not erase any of your data or settings.
DCS Codes 1 Remove the batteries.
DCS uses a digital signature and is not frequency-based. DCS
squelch codes may differ in some radios from third-party 2 Reinstall the batteries (Installing the Lithium-ion Battery,
page 1).
manufacturers. For the best results, you should compare the
DCS-code information for your third-party radio with the
information in this table. My device does not turn on
• Verify the battery is installed correctly (Installing the Lithium-
ion Battery, page 1).

20 Troubleshooting
• Fully charge the battery (Charging the Battery Pack, page 1). Ascent - Total: The total elevation distance ascended since the
last reset.
The battery gauge does not seem accurate Automotive Turn: The direction of the next turn in the route.
1 Allow the device to fully discharge. You must be navigating for this data to appear.
2 Fully charge the device without interrupting the charge cycle. Average Cadence: The average cadence for the current
activity.
My phone will not connect to the device Average HR: The average heart rate for the current activity.
• Select Setup > Bluetooth. Avg HR %Max.: The average percentage of maximum heart
The Bluetooth option must be enabled. rate for the current activity.
• Enable Bluetooth wireless technology on your phone and Avg Lap: The average lap time for the current activity.
bring your phone within 10 m (33 ft.) of the device. Barometer: The calibrated current pressure.
• Go to www.garmin.com/bluetooth for more help. Battery Level: The remaining battery power.
Bearing: The direction from your current location to a
My device is not acquiring satellite signals destination. You must be navigating for this data to appear.
• Verify the GPS simulator is turned off (Simulating a Location, Cadence: The number of revolutions of the crank arm or
page 12). number of strides per minute. Your device must be
• Take your device out of parking garages and away from tall connected to a cadence accessory for this data to appear.
buildings and trees. Calories: The amount of total calories burned.
• Remain stationary for several minutes. Compass Hdg.: The direction you are moving based on the
compass.
My device does not go into mass storage Course: The direction from your starting location to a
mode automatically destination. Course can be viewed as a planned or set route.
If your device is connected to the computer but does not go into You must be navigating for this data to appear.
mass storage mode automatically, you might have loaded a Current Lap: The stopwatch time for the current lap.
corrupt file. Date: The current day, month, and year.
1 Disconnect the device from your computer. Depth: The depth of the water. Your device must be connected
2 Turn off the device. to a NMEA 0183 or NMEA 2000 device capable of acquiring
® ®

3 Hold while you connect the device to your computer. the water depth.
4 Continue holding for 30 seconds or until the device goes Descent - Average: The average vertical distance of descent
into mass storage mode. since the last reset.
Descent - Maximum: The maximum rate of descent in feet per
I need to reset all settings back to factory minute or meters per minute since the last reset.
default values Descent - Total: The total elevation distance descended since
Select Setup > Reset > Reset All Settings. the last reset.
Distance To Dest.: The remaining distance to the final
destination. You must be navigating for this data to appear.
Appendix Distance To Next: The remaining distance to the next waypoint
on the route. You must be navigating for this data to appear.
tempe™ Elapsed Activity Time: The total time recorded. For example, if
The tempe is an ANT+ wireless temperature sensor. You can you start the timer and run for 10 minutes, then stop the timer
attach the sensor to a secure strap or loop where it is exposed for 5 minutes, then start the timer and run for 20 minutes,
to ambient air, and therefore, provides a consistent source of your elapsed time is 35 minutes.
accurate temperature data. You must pair the tempe with your
Elev Abv Ground: The altitude of your current location above
device to display temperature data from the tempe.
ground level (if maps contain sufficient elevation information).
Elevation: The altitude of your current location above or below
Data Fields sea level.
Some data fields require you to be navigating or require ANT+
accessories to display data. Elevation - Maximum: The highest elevation reached since the
last reset.
24 hr Max. Temperature: The maximum temperature recorded
in the last 24 hours. Elevation - Minimum: The lowest elevation reached since the
last reset.
24 hr Min. Temperature: The minimum temperature recorded in
the last 24 hours. ETA at Destination: The estimated time of day when you will
reach the final destination (adjusted to the local time of the
Accuracy of GPS: The margin of error for your exact location. destination). You must be navigating for this data to appear.
For example, your GPS location is accurate to within +/- 12 ft.
(3.65 m). ETA at Next: The estimated time of day when you will reach the
next waypoint on the route (adjusted to the local time of the
Activity Distance: The distance traveled for the current track. waypoint). You must be navigating for this data to appear.
Alarm Timer: The current time of the countdown timer. Glide Ratio: The ratio of horizontal distance traveled to the
Ambient Pressure: The uncalibrated environmental pressure. change in vertical distance.
Ascent - Average: The average vertical distance of ascent Glide Ratio to Dest.: The glide ratio required to descend from
since the last reset. your current position to the destination elevation. You must
Ascent - Maximum: The maximum rate of ascent in feet per be navigating for this data to appear.
minute or meters per minute since the last reset. GPS Elevation: The altitude of your current location using GPS.

Appendix 21
GPS Heading: The direction you are moving based on GPS. Temperature: The temperature of the air. Your body
GPS Signal Strength: The strength of the GPS satellite signal. temperature affects the temperature sensor.
Grade: The calculation of rise (elevation) over run (distance). Temperature - Water: The temperature of the water. Your
For example, if for every 10 ft. (3 m) you climb you travel device must be connected to a NMEA 0183 device capable
200 ft. (60 m), the grade is 5%. of acquiring the water temperature.
Heading: The direction you are moving. Time of Day: The current time of day based on your current
location and time settings (format, time zone, daylight saving
Heart Rate: Your heart rate in beats per minute (bpm). Your time).
device must be connected to a compatible heart rate monitor.
Time to Destination: The estimated time remaining before you
Heart Rate - %Max.: The percentage of maximum heart rate. reach the destination. You must be navigating for this data to
Heart Rate Zone: The current range of your heart rate (1 to 5). appear.
The default zones are based on your user profile and Time to Next: The estimated time remaining before you reach
maximum heart rate (220 minus your age). the next waypoint in the route. You must be navigating for
Lap Ascent: The vertical distance of ascent for the current lap. this data to appear.
Lap Cadence: The average cadence for the current lap. To Course: The direction in which you must move to get back
Lap Descent: The vertical distance of descent for the current on the route. You must be navigating for this data to appear.
lap. Total Lap: The stopwatch time for all the completed laps.
Lap Distance: The distance traveled for the current lap. Trip Odometer: A running tally of the distance traveled since
Lap Heart Rate Percent: The average percentage of maximum the last reset.
heart rate for the current lap. Trip Time: A running tally of the total time spent moving and not
Lap HR: The average heart rate for the current lap. moving since the last reset.
Laps: The number of laps completed for the current activity. Trip Time - Moving: A running tally of the time spent moving
since the last reset.
Lap Speed: The average speed for the current lap.
Trip Time - Stopped: A running tally of the time spent not
Last Lap Ascent: The vertical distance of ascent for the last
moving since the last reset.
completed lap.
Turn: The angle of difference (in degrees) between the bearing
Last Lap Cadence: The average cadence for the last
to your destination and your current course. L means turn
completed lap.
left. R means turn right. You must be navigating for this data
Last Lap Descent: The vertical distance of descent for the last to appear.
completed lap.
Velocity Made Good: The speed at which you are closing on a
Last Lap Distance: The distance traveled for the last completed destination along a route. You must be navigating for this
lap. data to appear.
Last Lap HR: The average heart rate for the last completed lap. Vert Dist to Dest: The elevation distance between your current
Last Lap Speed: The average speed for the last completed lap. position and the final destination. You must be navigating for
Last Lap Time: The stopwatch time for the last completed lap. this data to appear.
Location (lat/lon): The current position in latitude and longitude Vert Dist to Next: The elevation distance between your current
regardless of the selected position format setting. position and the next waypoint in the route. You must be
navigating for this data to appear.
Location (selected): The current position using the selected
position format setting. Vertical Speed: The rate of ascent or descent over time.
Location of Dest.: The position of your final destination. You Vertical Speed to Dest.: The rate of ascent or descent to a
must be navigating for this data to appear. predetermined altitude. You must be navigating for this data
to appear.
None: This is a blank data field.
Waypoint at Dest.: The last point on the route to the
Odometer: A running tally of distance traveled for all trips. This destination. You must be navigating for this data to appear.
total does not clear when resetting the trip data.
Waypoint at Next: The next point on the route. You must be
Off Course: The distance to the left or right by which you have navigating for this data to appear.
strayed from the original path of travel. You must be
navigating for this data to appear.
Heart Rate Zone Calculations
Pointer: An arrow points in the direction of the next waypoint or
turn. You must be navigating for this data to appear. Zone % of Perceived Exertion Benefits
Maximum
Speed: The current rate of travel. Heart Rate
Speed Limit: The reported speed limit for the road. Not 1 50–60% Relaxed, easy pace, Beginning-level
available in all maps and in all areas. Always rely on posted rhythmic breathing aerobic training,
road signs for actual speed limits. reduces stress
Speed - Maximum: The highest speed reached since the last 2 60–70% Comfortable pace, Basic cardiovascular
reset. slightly deeper training, good
breathing, conversation recovery pace
Speed - Moving Avg.: The average speed while moving since possible
the last reset. 3 70–80% Moderate pace, more Improved aerobic
Speed - Overall Avg.: The average speed while moving and difficult to hold capacity, optimal
stopped since the last reset. conversation cardiovascular training
Stopwatch Timer: The stopwatch time for the current activity.
Sunrise: The time of sunrise based on your GPS position.
Sunset: The time of sunset based on your GPS position.

22 Appendix
Zone % of Perceived Exertion Benefits
Maximum
Heart Rate
4 80–90% Fast pace and a bit Improved anaerobic
uncomfortable, breathing capacity and
forceful threshold, improved
speed
5 90–100% Sprinting pace, Anaerobic and
unsustainable for long muscular endurance,
period of time, labored increased power
breathing

Appendix 23
 Index emergency alerts 5 R
radio 3
F app 3
A FCC, licensing 20 contact 4
accessories 12, 13 files, transferring 7, 11, 17, 18 note 4
activities 7, 8, 12 fitness 16 peer-to-peer positioning 4
custom 8 scan 4
addresses, finding 9 G
settings 5
alarms Garmin Connect 5
volume 3
clock 12 storing data 12
registering the device 6
marine 16 Garmin Express, updating software 17
resetting the device 16, 20, 21
proximity 11 geocaches 6, 7, 17
restoring, settings 16
tones 15 downloading 6, 7
routes 10, 11
almanac navigating to 6
creating 10, 11
hunting and fishing 12 settings 16
deleting 11
sunrise and sunset times 12 GLONASS 15
editing 11
altimeter 10, 15 GPS 3, 12, 15
settings 15
ANT+ sensors 16 signal 12
viewing on the map 11
pairing 13
H
ANT+ sensors, pairing 13
heading setting 15
S
app drawer 2 satellite signals 12
customizing 13 headphones 5, 17
acquiring 3
applications 5 heart rate, zones 13, 22
locations 12
area calculation 12 history 12
scan 4
Auto Lap 16 sending to computer 12
screen, locking 2
viewing 12
settings 14–16
B HomePort 17
device 15
backlight 2, 13 hunting and fishing times 12
sharing data 11
barometer 10 shortcuts 14
BaseCamp 11, 17
I
ID number 20 adding 14
battery 1, 18 Sight 'N Go 9
charging 1 K smartphone 5
installing 1 keys 2, 13 applications 5
maximizing 2, 13, 17 software, updating 17
problems 21 L specifications 18
storage 1 lifetime athlete 16 squelch 3, 4
Bluetooth technology 5, 21 locations stopwatch 12
editing 10 storing data 18
C saving 10 sunrise and sunset times 12
calendar 12 locking, screen 2
calibrating system settings 15
altimeter 10 M T
compass 9 main menu, customizing 13 tempe 21
camera 11 map settings 14 temperature 18, 21
carabiner clip 17 maps 9, 14 time, zones and formats 16
channel 3, 4 data fields 14 time settings 16
frequency 18, 19 navigating 9 timer 12
repeater 4 optional 9 countdown 12
charging 1 settings 14 tones 15
chirp 7, 16 updating 17 touchscreen 14
City Navigator 9 marine TracBack 9
cleaning the device 17 alarms setup 16 tracks 8
cleaning the touchscreen 17 settings 16 training 5
code 3, 4, 20 memory card 17 transferring, files 7, 11, 17
frequency 20 microphone 5, 17 trip planner. See routes
compass 9 microSD card 1, 17. See memory card troubleshooting 16, 20, 21
navigating 9
settings 15 N U
computer, connecting 18 navigation 9, 10 unit ID 20
Connect IQ 5 compass 9 units of measure 16
contact 4 course pointer 9 USB 21
countdown timer 12 Sight 'N Go 9 connector 1
customizing the device 13, 14 stopping 9 disconnecting 18
note 4 mass storage mode 17, 21
D notifications 12 transferring files 17
dashboards 13, 14 user data, deleting 18
data P user profile 16
storing 12 pairing 5
transferring 12, 18 ANT+ sensors 13 V
data fields 5, 14, 21 ANT+ sensors 13 VIRB Remote 12
deleting phone 21
all user data 18 peer-to-peer positioning 4 W
history 12 phone, pairing 21 water resistance 17
device, care 17 photos 11 waypoints 9, 10
display settings 14 taking 11 deleting 10
downloading, geocaches 6, 7 position format 15 editing 10
power key 2 projecting 10
E product registration 7 saving 10
elevation 10 profiles, user 16 weather 5, 6
plot 8, 10, 11 proximity alarms 11 radio 6
emergency alert 5 Where To? 9

24 Index
widgets 2, 5
Z
zones, heart rate 13

Index 25
 support.garmin.com

May 2020 GUID-35474A49-ADDB-451D-A6DA-AA003B2A4ACC v5