Scribd
Upload
152 views7 pages

The Adaptive Equalizer: Abstract

The document discusses an adaptive equalizer used in non-line-of-sight communication systems impacted by multipath propagation. Multipath causes signal distortion through delay spread and inter-symbol interference. An adaptive equalizer aims to design an approximate inverse filter to cancel out distortion by finding the channel response and applying the inverse filter. It can estimate the channel response over time using a feedback loop to adapt to the unpredictable and time-varying channel conditions. The goal is to overcome multipath and inter-symbol interference in narrowband systems like GSM.

Uploaded by

Monalish Panda
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
152 views7 pages

The Adaptive Equalizer: Abstract

The document discusses an adaptive equalizer used in non-line-of-sight communication systems impacted by multipath propagation. Multipath causes signal distortion through delay spread and inter-symbol interference. An adaptive equalizer aims to design an approximate inverse filter to cancel out distortion by finding the channel response and applying the inverse filter. It can estimate the channel response over time using a feedback loop to adapt to the unpredictable and time-varying channel conditions. The goal is to overcome multipath and inter-symbol interference in narrowband systems like GSM.

Uploaded by

Monalish Panda
Copyright
© Attribution Non-Commercial (BY-NC)
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 7

THE ADAPTIVE EQUALIZER

ABSTRACT:

Non line-of-sight systems such as mobile communications


are severely affected by the multi-path effect.

In non line-of-sight communication, there is no direct path


for the signal from the Transmitter to Receiver. This results
in signal undergoing multiple reflections, diffractions,
scattering before reaching the receiver. As a result, multiple
copies of the same signal arrive at the receiver at successive
time intervals.

This multi-path propagation distorts the signal reception by


introducing delay spread and inter-symbol-interference (ISI)

Equalization is a technique which is used to overcome the


affects of multi-path and ISI in narrowband systems such as
GSM.

It involves finding the channel response H(f) of the medium


through which signal traversed. The received signal is then
passed through an inverse filter (1/H(f)) which nullifies the
effect of the channel.

H(f) can be estimated at the receiver by using methods like


training sequence, pilot carrier etc., H(f) being a random
function ( since channel condition is unpredictable) can be
estimated from time-to-time using a feedback loop
( adaptive method)

This project aims at such an adaptive equalizer based upon


the wiener solution using MATLAB.
goal:

Design an approximate inverse filter to cancel out as


much
distortion as possible.

Figure 1Figure 1 (fig1AdaptiveEqual.png)

In principle,

WH≈
z

-
Δ

W
H

-
Δ

, or

W≈
z

-
Δ

-
Δ

, so that the overall response of the top path is


approximately

δn−Δ

n
Δ
. However, limitations on the form of
WW (FIR) and the presence of noise
cause the equalization to be imperfect.

Important Application

Channel equalization in a digital communication


system.

Figure 2Figure 2 (fig2AdaptiveEqual.png)

If the channel distorts the pulse shape, the matched


filter will no longer be matched, intersymbol
interference may
increase, and the system performance will degrade.

An adaptive filter is often inserted in front of the


matched
filter to compensate for the channel.

Figure 3Figure 3 (fig3AdaptiveEqual.png)


This is, of course, unrealizable, since we do not have
access
to the original transmitted signal,

s
k

s
k

There are two common solutions to this problem:

1. Periodically broadcast a known training


signal. The adaptation is switched on only when the
training signal is being broadcast and thus

s
k

s
k
is known.

2. Decision-directed feedback: If the overall system is


working well, then the output

ŝ
k
-

Δ
0

k
-

Δ
0

should almost always equal

k
-

Δ
0
s

k
-

Δ
0

. We can thus use our received digital


communication signal as the desired signal, since it
has
been cleaned of noise (we hope) by the nonlinear
threshold
device!

Figure4Decision-directed equalizer

Decision-directed equalizer (fig4AdaptiveEqual.png)

You might also like