Rod seal C1

The profile C1 rod seal meets the requirements of the manufacturers of hy-
draulic and pneumatic equipment for seals with the smallest possible hous-
ings. Although cross-sections and heights are very small, the sealing perfor-
mance is excellent.

Extremely low friction is experienced because of the short contact of the

sealing surface area. Back-up rings or brackets are not required because of
the special design.

.
Use in pneumatic equipment is only possible when consistent supply of lubri-

r.o
cant such as oiled air is assured. For installation in non-lubricated pneumatic
systems (dry air) we recommend our profile E5 which fits into the same hous-
ings.

• Good wear resistance. Range of application

• Easier installation. The profile C1 rod seal is especially recommended for plungers, piston rods,
• High temperature resistance in case
of suitable compound selection.
• Excellent media resistance in case
of suitable compound selection.
• Suitable compounds available for
special requirements of the chemi-
cal process industry.
• Suitable compounds available for
special requirements of the food
s.
stems and valve lifters as well as for slowly operating pneumatic rotors
(v ≤ 0,2 m/s).

Working pressure 1)
Hydraulics
Pneumatics
for rotary transmissions
Working temperature
≤ 160 bar
≤ 16 bar
≤ 20 bar
z
processing industry. Hydraulics -35 °C to +100 °C
• Installation in closed and undercut Pneumatics -35 °C to +80 °C
housings. Surface speed
Hydraulics ≤ 0.5 m/s
va

Pneumatics ≤ 1 m/s
for rotary transmissions ≤ 0.2 m/s
Recommendation for rotary transmissions: P ∙ v ≤ 3
(Definition see catalogue “Hydraulic Seals”, chapter “Other, Rotary Seals”,
introduction.)

1)
Dependent upon cross-section and compound.

Compounds
ko

Standard: N3571, NBR compound (≈ 70 Shore A)

for low temperatures: N8602, NBR compound (≈ 70 Shore A)
for high temperatures: V3664, FKM compound (≈ 85 Shore A)

Installation
The profile C1 rod seals are manufactured over-sized on the external diam-
eters in relation to the nominal dimensions. This ensures the required tight fit.
Only after installation the sealing lip diameter will show the desired dimen-
sions. Profile C1 can easily be snapped into the grooves.
When choosing a seal for a particular diameter, it is best to select the one
with the largest possible cross-section.

Pneumatic Seals
30 Parker Hannifin GmbH
Packing Division Europe
Rod seal C1

Note: For nominal diameters ≤ 25 mm an open housing is recommended,

according to the seals cross-section and the position of the groove (stuffing
box installation).

In case of special operating conditions (specific pressure loads, temperature, speed, use in water, HFA,
HFB fluids etc.), please contact our consultancy service for a selection of the material and design best suit-
ing your particular application requirements.

.
r.o
Rod seals
s.
z
va
ko

Pneumatic Seals
31 Parker Hannifin GmbH
Packing Division Europe
Rod seal C1

L+ 0,2
R ≤ 0,2
H “e” see chapter “Maximum gap
R ≤ 0,2 R ≤ 0,2 allowance”

R ≤ 0,2

.
r.o
e9 )
(Pneu. H11
Ø DH9

H8
Ø df7
ØD

Ød

For surface finish, lead in chamfer and other installation dimensions see “General installation guidelines”.

d, D, H, L, Order code d, D, H, L, Order code

2 7 3.5 4 C1 0003 N3571 11 17 4 4.5 C1 1022 N3571
3 7 3 3.5 C1 0005 N3571 11 18 4.5 5 C1 1025 N3571
3 9 4.5 5 C1 0009 N3571 12 18.5 4.5 5 C1 1028 N3571
3
4
4
4
4
4
4
4.5
10
8
9
10
12
12
14
8
5
3
3.5
4.2
4.5
5.5
5.8
3
5.5
3.5
4
4.7
5
6
6.3
3.5
s.
C1 0011 N3571
C1 0013 N3571
C1 0016 N3571
C1 0019 N3571
C1 0022 N3571
C1 0024 N3571
C1 0028 N3571
C1 0032 N3571
12
12
12.75
13
13.8
14
14
14
19
20
19.2
17.5
22
19
20
22
4.5
5.5
3.8
2.8
5.5
3.5
4.8
5.5
5
6
4.3
3.3
6
4
5.3
6
C1 1030 N3571
C1 1033 N3571
C1 1035 N3571
C1 1036 N3571
C1 1037 N3571
C1 1039 N3571
C1 1040 N3571
C1 1041 N3571
5 9 2.5 3 C1 0035 N3571 14 25 8 8.5 C1 1042 N3571
z
5 10 4 4.5 C1 0038 N3571 15 22 5 5.5 C1 1044 N3571
5 12 4.5 5 C1 0041 N3571 15.8 24 5.5 6 C1 1047 N3571
6 10 3 3.5 C1 0055 N3571 16 22.5 4.5 5 C1 1049 N3571
6 12 4.2 4.7 C1 0058 N3571 16 23 5.5 6 C1 1051 N3571
va

6 13 5 5.5 C1 0059 N3571 16 23.5 5.5 6 C1 1052 N3571

6 15 7 7.5 C1 0062 N3571 16 24 5.5 6 C1 1053 N3571
6 16 5 5.5 C1 0065 N3571 16 26 7 7.5 C1 1056 N3571
7 13 4 4.5 C1 0070 N3571 16 27 7.5 8 C1 1058 N3571
8 14 4 4.5 C1 0074 N3571 17 25 5.5 6 C1 1060 N3571
8 14.5 4.5 5 C1 0077 N3571 18 25 4.5 5 C1 1062 N3571
8 16 5.5 6 C1 0080 N3571 18 25 5.5 6 C1 1063 N3571
8 18 8 8.5 C1 0083 N3571 18 26 5.5 6 C1 1066 N3571
ko

9 14 3.5 4 C1 0087 N3571 18 30 8.5 9.5 C1 1070 N3571

9.3 14 3 3.5 C1 0090 N3571 18.5 25.5 5.5 6 C1 1074 N3571
9.5 18.5 7 7.5 C1 0094 N3571 19 25 5 5.5 C1 1079 N3571
10 13.6 2.3 2.7 C1 1002 N3571 20 26 4 4.5 C1 2003 N3571
10 15 3.5 4 C1 1005 N3571 20 26 4.8 5.3 C1 2005 N3571
10 16 4.5 5 C1 1008 N3571 20 28 5.5 6 C1 2009 N3571
10 16 6 6.5 C1 1011 N3571 20 28 8 8.5 C1 2013 N3571
10 18 5.5 6 C1 1015 N3571 20 30 7 7.5 C1 2020 N3571
10 20 7 7.5 C1 1018 N3571 20 32 7 7.5 C1 2022 N3571
10.4 15.2 3.5 4 C1 1020 N3571 22 29 5.5 6 C1 2025 N3571
Further sizes on request.

Pneumatic Seals
32 Parker Hannifin GmbH
Packing Division Europe
Rod seal C1

L+ 0,2
R ≤ 0,2
H “e” see chapter “Maximum gap
R ≤ 0,2 R ≤ 0,2 allowance”

R ≤ 0,2

.
r.o
e9 )
(Pneu. H11
Ø DH9

H8
Ø df7
ØD

Ød

For surface finish, lead in chamfer and other installation dimensions see “General installation guidelines”.

d, D, H, L, Order code d, D, H, L, Order code

Rod seals
22 30 5.5 6 C1 2029 N3571 38 48 7 7.5 C1 3060 N3571
22 32 7 7.5 C1 2031 N3571 40 48 8 8.5 C1 4010 N3571
22 32 8 8.5 C1 2030 N3571 40 50 7 7.5 C1 4015 N3571
22
23
24
25
25
25
25
25
34
31
32
32
33
33
35
35
8.5
5.5
5.5
5.5
5.5
8
6
7
9.5
6
6
6
6
8.5
6.5
7.5
s.
C1 2033 N3571
C1 2038 N3571
C1 2043 N3571
C1 2053 N3571
C1 2058 N3571
C1 2061 N3571
C1 2064 N3571
C1 2065 N3571
40
42
44
45
45
45
46
47
52
52
54
53
55
60
56
57
8.5
7
7
5.5
7
10
7
7
9.5
7.5
7.5
6
7.5
11
7.5
7.5
C1 4020 N3571
C1 4025 N3571
C1 4030 N3571
C1 4505 N3571
C1 4035 N3571
C1 4040 N3571
C1 4046 N3571
C1 4055 N3571
25 36 8 8.5 C1 2066 N3571 48 58 7 7.5 C1 4060 N3571
z
25 37 8.5 9.5 C1 2069 N3571 50 58 8 8.5 C1 5005 N3571
25 40 10 11 C1 2075 N3571 50 60 7 7.5 C1 5010 N3571
26 36 7 7.5 C1 2078 N3571 50 63 8.5 9.5 C1 5015 N3571
28 36 5.5 6 C1 2085 N3571 50 63 12 13 C1 5017 N3571
va

28 38 7 7.5 C1 2089 N3571 50 66 11 12 C1 5020 N3571

28 40 8.5 9.5 C1 2095 N3571 54 64 7 7.5 C1 5035 N3571
30 38 5.5 6 C1 3005 N3571 55 65 7 7.5 C1 5040 N3571
30 38 8 8.5 C1 3010 N3571 56 66 7 7.5 C1 5043 N3571
30 40 7 7.5 C1 3015 N3571 56 70 12 13 C1 5044 N3571
30 42 8 8.5 C1 3019 N3571 57 67 7 7.5 C1 5053 N3571
30 42 8.5 9.5 C1 3020 N3571 58 68 7 7.5 C1 5058 N3571
32 40 5.5 6 C1 3025 N3571 59 71 7.5 8 C1 5085 N3571
ko

32 42 7 7.5 C1 3030 N3571 60 72 8.5 9.5 C1 6005 N3571

32 45 10 11 C1 3032 N3571 60 80 14 15 C1 6010 N3571
33 43 7 7.5 C1 3035 N3571 63 73 7 7.5 C1 6025 N3571
34 44 7 7.5 C1 3040 N3571 63 75 8.5 9.5 C1 6035 N3571
35 43 8 8.5 C1 3045 N3571 63 78 8.5 9.5 C1 6036 N3584
35 45 7 7.5 C1 3050 N3571 63 80 16 17 C1 6037 N3571
36 44 5.5 6 C1 3605 N3571 64 76 7.5 8 C1 6040 N3571
36 46 7 7.5 C1 3055 N3571 65 77 8.5 9.5 C1 6055 N3571
36 50 10 11 C1 3057 N3571 68 80 8.5 9.5 C1 6070 N3571
37 47 7 7.5 C1 3059 N3571 70 82 8.5 9.5 C1 7003 N3571
Further sizes on request.

Pneumatic Seals
33 Parker Hannifin GmbH
Packing Division Europe
Rod seal C1

L+ 0,2
R ≤ 0,2
H “e” see chapter “Maximum gap
R ≤ 0,2 R ≤ 0,2 allowance”

R ≤ 0,2

.
r.o
e9 )
(Pneu. H11
Ø DH9

H8
Ø df7
ØD

Ød

For surface finish, lead in chamfer and other installation dimensions see “General installation guidelines”.

d, D, H, L, Order code d, D, H, L, Order code

75 87 8.5 9.5 C1 7020 N3571 155 170 10 11 C1 F053 N3571
75 95 14 15 C1 7030 N3571 155 175 14 15 C1 F055 N3571
80 90 7 7.5 C1 8010 N3571 160 180 14 15 C1 G015 N3571
80
80
80
85
85
88
90
90
92
92
100
97
100
100
102
102
7.5
8.5
14
8.5
10
8.5
6.5
8.5
8
9.5
15
9.5
11
9.5
7
9.5
s.
C1 8013 N3571
C1 8015 N3571
C1 8025 N3571
C1 8040 N3571
C1 8045 N3571
C1 8070 N3571
C1 9014 N3571
C1 9015 N3571
160
166
170
170
180
185
185
190
184
188
190
194
200
210
215
210
15
15.5
14
15
14
17.5
20
14
16
16.5
15
16
15
18.5
21
15
C1 G024 N3571
C1 G040 N3571
C1 H007 N3571
C1 H010 N3571
C1 J005 N3571
C1 J025 N3571
C1 J032 N3571
C1 K010 N3571
90 110 16 17 C1 9018 N3571 200 220 14 15 C1 L015 N3571
z
95 107 8.5 9.5 C1 9035 N3571 200 230 15 16 C1 L025 N3571
100 110 7 7.5 C1 A010 N3571 210 230 14 15 C1 L040 N3571
100 115 10 11 C1 A015 N3571 220 250 20 21 C1 M017 N3571
105 120 10 11 C1 A051 N3571 225 250 14 15 C1 M020 N3571
va

105 125 12 13 C1 A055 N3571 235 265 21 22 C1 M030 N3571

110 125 10 11 C1 B015 N3571 240 270 20 21 C1 N035 N3571
110 130 14 15 C1 B020 N3571 260 280 14 15 C1 O007 N3571
115 130 10 11 C1 B040 N3571 260 290 21 22 C1 O010 N3571
115 135 14 15 C1 B045 N3571 280 310 20 21 C1 O031 N3571
120 135 10 11 C1 C015 N3571 310 330 14 15 C1 Q001 N3571
120 140 14 15 C1 C020 N3571 320 350 20 21 C1 Q050 N3571
125 140 10 11 C1 C035 N3571
ko

125 145 12 13 C1 C037 N3571

130 145 10 11 C1 D015 N3571
130 150 14 15 C1 D020 N3571
135 150 10 11 C1 D035 N3571
140 160 14 15 C1 E015 N3571
142 157 10 11 C1 E035 N3571
145 165 12 13 C1 E049 N3571
145 165 13 14 C1 E050 N3571
150 170 14 15 C1 F020 N3571
154 176 15.5 16.5 C1 F040 N3571
Further sizes on request.

Pneumatic Seals
34 Parker Hannifin GmbH
Packing Division Europe