Scribd Logo
Upload

Welcome to Scribd!

  • 263 views

    En 33 C 178-Grundfos-Upm3-Auto4

    Uploaded by

    Красимир Георги
    The document provides assembly instructions for a Grundfos UPM3 Auto L 15/70 pump. It can be set to one of ten settings, including three constant pressure curves and four constant curve options. It is delivered preset to proportional pressure curve three. Installers are advised to change it to a constant pressure curve suitable for underfloor heating installations. The document describes how to change the setting by pressing and holding the pump button for 2-10 seconds to cycle through the settings menu. It also provides an overview of the pump dimensions, diagram, and electrical connection requirements.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    En 33 C 178-Grundfos-Upm3-Auto4

    Uploaded by

    Красимир Георги
    263 views2 pages
    The document provides assembly instructions for a Grundfos UPM3 Auto L 15/70 pump. It can be set to one of ten settings, including three constant pressure curves and four constant curve options. It is delivered preset to proportional pressure curve three. Installers are advised to change it to a constant pressure curve suitable for underfloor heating installations. The document describes how to change the setting by pressing and holding the pump button for 2-10 seconds to cycle through the settings menu. It also provides an overview of the pump dimensions, diagram, and electrical connection requirements.

    Original Description:

    Grundfos UPM3 Auto L 15/70

    Original Title

    en.33.c.178-grundfos-upm3-auto4

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document provides assembly instructions for a Grundfos UPM3 Auto L 15/70 pump. It can be set to one of ten settings, including three constant pressure curves and four constant curve options. It is delivered preset to proportional pressure curve three. Installers are advised to change it to a constant pressure curve suitable for underfloor heating installations. The document describes how to change the setting by pressing and holding the pump button for 2-10 seconds to cycle through the settings menu. It also provides an overview of the pump dimensions, diagram, and electrical connection requirements.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    263 views2 pages

    En 33 C 178-Grundfos-Upm3-Auto4

    Uploaded by

    Красимир Георги
    The document provides assembly instructions for a Grundfos UPM3 Auto L 15/70 pump. It can be set to one of ten settings, including three constant pressure curves and four constant curve options. It is delivered preset to proportional pressure curve three. Installers are advised to change it to a constant pressure curve suitable for underfloor heating installations. The document describes how to change the setting by pressing and holding the pump button for 2-10 seconds to cycle through the settings menu. It also provides an overview of the pump dimensions, diagram, and electrical connection requirements.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    Assembly instructions | Grundfos UPM3 Auto L 15/70

    Grundfos UPM3 Auto L 15/70


    Introduction
    Grundfos UPM3 Auto L 15/70 is a compact, ener-
    gy-saving and high-performance pump specifi-
    cally developed for the OEM market. LK uses
    UPM3 Auto L in several products because of its
    good characteristics.

    The pump has ten different setting options, three


    curves for Proportional Pressure, three curves for
    Constant Pressure and four curves for Constant
    Curve. The recommendation for underfloor heat-
    ing is Constant Pressure and a curve that is adapt-
    ed to conditions for the installation. The pump is
    set to Proportional Pressure, curve three, on deliv-
    ery.

    Operating mode / Settings mode


    Grundfos UPM3 Auto L indicates in normal oper-
    ation the power used by the pump (stated in per
    cent of maximum capacity) in accordance with the To change the pump setting press the button on
    table below. the pump for 2-10 seconds, when the pump will
    show the selected setting in accordance with the
    settings menu. Pressing the button shifts the
    pump between the different settings. Adjust to the
    desired setting using the menu.
    Note that for floor heating Constant Pressure is
    recommended with a curve that is suitable for the
    installation needs.

    Note!
    The pump is set to Proportional Pressure,
    Table, overview of operating mode.
    curve three, on delivery.
    To show the setting currently in use by the pump, This must be manually changed to Constant
    give the button a short press . Read the selected Pressure by the installer when the pump is
    mode by studying the settings menu. After two used in floor heating installations.
    seconds the indicator returns to operating mode.

    To show the current setting, press


    once on the button

    To view the settings menu, hold the


    button pressed for 2-10 seconds

    When the setting changes are com-


    plete, the pump returns to operat-
    ing mode after 10 seconds

    SE.33.C.178.1509

    1
    Assembly instructions | Grundfos UPM3 Auto L 15/70

    Settings menu
    Display Indication Operation Action
    Red LED, Electric Pump stops Check volt-
    Yellow LED fault because of age to pump
    #3 low voltage or / Replace
    serious fault pump

    Dimensions
    72 45 128
    36 92

    130
    90
    G1 Weight 1,9 kg

    Grundfos UPM3 Auto L 15/70 130

    Pump diagram

    Overview of settings options for the UPM3. Relevant set-


    tings are marked with a blue triangle, other settings
    are shaded.

    Lock
    The pump can be locked so that it is not possible
    to show or change settings. In order to lock/ Electrical contact
    unlock the pump then press the button for
    more than 10 seconds.

    The pump's electrical contact should be connected


    Alarm codes to a 230 V 50 hz socket by a qualified electrician in
    In the event of an operating problem then a fault accordance with the diagram above. This contact
    code will be displayed as below. no longer requires a 2-pole switch disconnecter.
    The electrical contact should be equipped with a
    Display Indication Operation Action slow-blow fuse of up to 10 A.
    Red LED, Blocked False start Wait or re- The pump should be disconnected from the mains
    Yellow LED rotor was 1.33 s. lease rotor before any maintenance work.
    #5
    Red LED, Too low Only one Check the
    Yellow LED voltage warning, the voltage to
    #4 pump oper- the pump
    ates as normal

    SE.33.C.178.1509

    You might also like