Scribd
Upload
75 views2 pages

DP CVM-C5 en

The CVM-C5 is a basic and affordable multifunction multimeter that is suitable for low voltage installations. It can measure in single-phase, bi-phase, and three-phase networks with 4 quadrant measurement capabilities. It has 1 built-in digital output, 1 digital input, and can measure maximum, minimum and maximum demand. It displays key parameters on its 96x96mm screen for quick monitoring.

Uploaded by

สมฤดี สิงห์ดี
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
75 views2 pages

DP CVM-C5 en

The CVM-C5 is a basic and affordable multifunction multimeter that is suitable for low voltage installations. It can measure in single-phase, bi-phase, and three-phase networks with 4 quadrant measurement capabilities. It has 1 built-in digital output, 1 digital input, and can measure maximum, minimum and maximum demand. It displays key parameters on its 96x96mm screen for quick monitoring.

Uploaded by

สมฤดี สิงห์ดี
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Measurement and Control

Technical features
Power-Supply Voltage supply 85-265 Vac / 50...60 Hz
95-300 Vdc

CVM-C5
Measure Voltage 300 Vac ph-n / 520 Vac ph-ph 50...60 Hz
Current ... /5A & /1 A
MC: ... /250 mA
Sampling rate 64 samples/cycle
Accuracy V, I, kW 0,5% Basic & affordable
Output
Energies
1 built-in digital output
1%
S0 interface
multifunction Multimeter
Configurable to 1000 impulses
by kWh, kVarh, etc.
(24 Vdc max, 50 mA, 5 imp/s,
Max Ton /Toff (configurable))
Input 1 built-in digital input Tariff selection The new generation of CVM
NPN, optoinsulated
Safety Protection Degree Frontal protection: IP51
Terminals: IP20
Class III category / EN 61010
Double-insulated electric shock protection class II
Standards IEC 664, VDE 0110, UL 94, IEC 801, IEC 348,
IEC 571-1, EN 61000-6-3, EN 61000-6-1,
EN 61010-1, CE, according to UL

References
Type Code Current input Input Output

CVM-C5-IC M55803 ... /5A and /1 A 1 1

CVM-C5-MC-IC M55823 /250 mA 1 1

w w w. c i r c u to r. co m
CIRCUTOR, SA - Vial Sant Jordi, s/n
08232 Viladecavalls (Barcelona) Spain
Tel. (+34) 93 745 29 00 - Fax: (+34) 93 745 29 14
[email protected]

Technology for energy efficiency

Designed by Communication Dept. - CIRCUTOR, SA. Code: C2M5D3-01


CVM-C5 Screen Data System
Basic & affordable Quick monitoring parameters with a single button.

multifunction Multimeter (96 x 96 mm)

Suitable for Low Voltage installations


Measures in Single-phase, Bi-phase (2-3 wires)
and Three-phase (3 or 4 wires) networks
4 Quadrant measurement
Measurements taken with /5 A or /1 A transformers or
the efficient transformers of CIRCUTOR’s MC range
Shows clearly the basic parameters of an electrical installation.
1 built-in digital output (S0 Interface)
1 built-in digital inputs (tariff selection) or load type
Maximum, Minimum and Maximum demand.

Get the Energy


consumption or
generation from two
different sources (Main
network/generator) and
Displays energy consumption value in cost by
see it over the screen.
configuring the kWh cost ratio.

Setup an alarm by a
¢¥
kWh £$€
configurable transistor
output parameter,
Low/High value,
Hysteresis (%),NO/NC,
delays to connection/
disconnection and Latch. Displays KgCO2 indicator in consumption/generation according
the energy nature, using the ratio established of the energy
mix in the country.
Or generating a impulse
signal related to the
kgCO2 cost, kgCO2 emissions
or savings according
the consumption or
kW kgCO2
generation electricity.

You might also like