SOYAL

®
AR-829E-V5 V120508
ACCESS CONTROL SYSTEM

Contents
1 Products 2 User Guide 3 Terminal Cables 4 Tools 5 Optional

P1 P2 P3

AR-721RB
P4 P5 P6 AR-821RB Digital Relay

Installation
3

1
1
2
3

6
Use a screwdriver to screw the mounting plate to the wall.
2
5

Pull cables ends through the access hole in the mounting plate.
4 9
8
7 #
0
*

Attach AR-829E to the mounting plate and install screws (supplied) into the
holes at the bottom with the allen key (supplied).
4 Apply power. LED (green) will light up.

Notice
1.Tubing: The communication wires and power line should NOT be bound in the same conduit or tubing.
2.Wire selection: Use AWG 22-24 Shielded Twist Pair to avoid star wiring ,CAT 5 cable for TCP/IP connection
3.Power supply: Don’t equip reader and lock with the same power supply. The power for reader may be unstable when the lock is activating, that may make the
reader malfunction.
The standard installation: Door relay and lock use the same power supply, and reader use independent power supply.

Connector Table
Cable: P3
Wire Application Wire Color Description
P3 P2 P4 1 --- ---
7 8 2
P7 6 7 1 2 --- ---
6 6
5
5
5 P6
TCP/IP Output 3 Orange White Net - TX+
4
4 3 4 4 4 Orange Net - TX-
3 2 3 3
2 1 2 2 5 Green White Net - RX+
1 1 1
6 Green Net - RX-
P5
3 2 1 8 7 6 5 4 3 2 1 P1 7 --- ---

Cable: P4
Wire Application Wire Color Description
Cable: P1 RS-485 for Lift 1 Thick Green RS-485(B-)
Controller 2 Thick Blue RS-485(A+)
Wire Application Wire Color Description
Lock Relay 1 Blue White (N.O.)DC24V1Amp Cable: P5
2 Purple White (N.C.)DC24V1Amp
Wire Application Wire Color Description
Lock Relay COM 3 White (COM)DC24V1Amp
Anti-Tamper Switch 1 Red N.C.
Door Contact 4 Orange Negative Trigger Input
2 Orange COM
Exit Switch 5 Purple Negative Trigger Input
3 Yellow N.O.
Alarm Relay 6 Gray DC24V1Amp
Power 7 Thick Red DC 12V Cable: P6
8 Thick Black DC 0V Wire Application Wire Color Description
Power 1 Red DC 12V Output
Security trigger signal 2 Purple Security trigger signal Output
Cable: P2 Arming 3 Red White Arming Output
Wire Application Wire Color Description Duress 4 Yellow White Duress Output
Beeper 1 Pink Beeper Output 5V/100mA, Low
2 Yellow Red LED Output 5V/20mA, Max Cable: P7 Optional:(Request to purchase AR-725L485 additionally)
LED
3 Brown Green LED Output 5V/20mA, Max Wire Application Wire Color Description
Transistor Output Max. 12V/100mA TTL Port 1 Black DC 0V
Door Output 4 Blue White
(Open Collector Active Low) 2 Yellow TX
5 Thin Green Wiegand DAT: 0 Input 3 White TE
Wiegand
6 Thin Blue Wiegand DAT: 1 Input 4 Orange RX
WG Door Contact 7 Orange Negative Trigger Input 5 Red DC 5V
WG Exit Switch 8 Purple Negative Trigger Input 6 --- ---

Copyright by SOYAL Technology Co., Ltd.. All rights reserved.

 LCD Access Controller
V120508

Front Panel & Indicator

Power(Green) OK(Green)
Alarm(Red) Error(Red)
Alarm(Green) In processing(Green)

1. System will automatically exit from Programming Mode when inactivating for 30 seconds.
2. LED status indicates controller’s mode and status.
OK (green) – blinking constantly when operates in Programming Mode
– or flashing an existed card in card learn mode, it comes 2 beeps warning and LCD panel displays “Same Card: user address / card number”
Error (red) – invalid card with 2 beeps warning and LCD panel displays “Card Number Err!”
– or in anti-pass-back mode, when violates the access, it comes one beep warning and LCD panel displays “Anti-pass Error!”
Arming (green) – arming on status
Alarm (red) – any abnormal condition occurs
3. Keypad will be locked up 30 sec. when constantly entering incorrect pin code or master code.
4. Maximum error in[ut of pin code and master code can be changed via the software 701Server (default: 5 times)

12/07 WED Duty : 0 12 07 WED Duty : 0

Networking : / and interactively flash between the Month and DAY.
PWR

14 : 49 : 04
OK PWR

14 : 49 : 04
OK
[e.g.] 12/07←→12 07
ERR ERR

Ready . . .
ARM
Ready . . .
PRE ARM PRE Stand-alone : No flashing [e.g.] 12/07
SE RI ES V 5 SE RI ES V 5 (←Reference to picture)

Wiring Diagram
Connect to Electric Bolt Connect to Magnet Lock

12V 12V
POWER 12V 12V
GND GND POWER
Exit Switch
12VDC GND GND
E 12VDC
Electric Bolt Magnet Lock

P1
N.O. 1 P1
2 1
COM 3 N.C. 2
4 COM 3
PB 5 4
6 PB 5
N.O. 6
12V 7 N.O.
GND
GND 8 12V 7
Controller EXIT
GND
Controller GND 8
EXIT
12V
POWER 12V
GND
12VDC RTE POWER GND
12VDC RTE

Connect to Electric Strike Connect to Door Contact

12V 12V POWER 12V 12V

GND GND
POWER
12VDC 12VDC GND GND
Electric Strike Alarm
P1 P1
N.O. 1 1
N.C.
2 2
N.O.
COM 3 3
COM
4 Door Contact 4
CTL
5
PB 5 12V
6 ALM 6
N.O. 12V 7 Relay Outpot Module
12V 7
GND GND 8
Controller GND 8
Controller
EXIT 12V N.C.
POWER
12V POWER
GND GND
12VDC 12VDC Door Contact
RTE

Copyright by SOYAL Technology Co., Ltd.. All rights reserved.

SOYAL
®
AR-829E-V5 V120508
ACCESS CONTROL SYSTEM

Strengthen security with AR-721RB Connect to Reader

12V
12V 12V
POWER GND
POWER
GND GND 12VDC Door Contact
12VDC E
Exit Switch

Electric Bolt N.C. Electric Bolt P2 N.C.

N.O. N.C. 1 BZ
COM
N.O. 2 RLED P1
CTL
12V COM 3 GLED 1
1 GND CTL 4 Door Output2
PB
P6 1 2 3 4 2 12V 5 WG 0 3
12V DDR 3 AR-721RB 6 WG 1 4
4 P1 7 WG-DS 5
5 8 WG-PB 6
6 N.O. 12V 7
EXIT
12V 7 GND 8
BZ
GND 8 RLED
Controller EXIT
GLED Controller RTE
WG 0
12V Reader WG 1
POWER 12V POWER
GND RTE
12VDC GND 12VDC

If any fire emergency, the people can escape by press a switch to open all doors

Electric Strike 12V

POWER Magnet Lock 12V Electric Bolt 12V
POWER
POWER GND
GND GND
12VDC 12VDC 12VDC
E

P1 P1 P1
N.O. 1 RTE 1 RTE N.O. 1 RTE
2 N.C. 2 2
COM 3 COM 3 COM 3
4 4 4
PB 5 PB 5 PB 5
6 6 6
12V 7 12V 12V 7
7 EXIT EXIT
EXIT GND 8
GND 8 GND 8
Transistor Transistor
IN4007 IN4007

Fire Emergency

Adding and Deleting Tag

※ User capacity: 16384 (00000~16383)
Adding Tag by Tag ID
Access programming mode → 1 Add/Delete → 1 Add -> Card ID → Input 5-digit user address → Input Site Code → Input Card Code

Adding Tag by RF Learn Function

Tag Information
Access programming mode → 1 Add/Delete → 2 Add -> RF-Learn → Input 5-digit user address
→ Input Tag Units(pcs) → Close Tag into RF Area
※If a batch of tags are Sequential, input Tag Units(pcs) in the quantity of the tags and present the tag with CARD CODE CARD CODE
SITE CODE SITE CODE
the lowest number to the controller.

Suspend User Address

Access programming mode → 1 Add/Delete → 3 Suspend -> Addr → Input Start address → Input End address

Suspend Tag by Tag ID

Access programming mode → 1 Add/Delete → 4 Suspend -> ID # → Input Site Code → Input Card Code

Recover User Address

Access programming mode → 1 Add/Delete → 7 Delete -> Addr → Input Start address → Input End address

Recover Tag by Tag ID

Access programming mode → 1 Add/Delete → 8 Delete -> ID # → Input Site Code → Input Card Code
Deleteing User Address
Access programming mode → 1 Add/Delete → 5 Delete -> Addr → Input Start address → Input End address

Deleteing Tag by Tag ID

Access programming mode → 1 Add/Delete → 6 Delete -> ID # → Input Site Code → Input Card Code
Setting up the access mode
Access programming mode → 2 User Setting → 2 Access Mode → Input User Address → 0: Invalid; 1: Card ; 2: Card or PIN; 3: Card & PIN

Copyright by SOYAL Technology Co., Ltd.. All rights reserved.

 LCD Access Controller
V120508

Programming
A. Keyboard Lock/ Unlock
Lock/ Unlock
Press and , and at the same time to lock keyboard. Press again to unlock.

B. Entering and Exiting Programming Mode

Entering
Input 123456 or PPPPPP
[e.g.] The Default Value= 123456. If already changed the Master Code= 876112, input 876112 → Access programming mode
P.S.If entering no instruction within 30 sec., it will automatically leave the programming mode.
Exiting
Press the repeatedly → 6 Quit or 7 Quit and Arming (Please refer to alarm / arming setting)

Changing the Master Code

Access programming mode → 5 Tools → 2 Master Code → Input the 6-digit new master code → Succeeded

C. Initial setup
Language Setting
Access programming mode → 5 Tools → 1 Language → 0 EN → Succeeded → Initial system...

Node ID of Reader Setting

Access programming mode → 3 Parameters[1] → 1 Node ID → Input New Node ID : 1~254 (default value:001) → Main Door Number : 0~255
→ WG1 Door Number : 0~255 → Show UID (0=No,1=WG,2=ABA,3=HEX) → Enable DHCP(0:No,1:En,2=Exit) → Succeeded

D. PIN Code
Access programming mode → 2 User Setting → 1 Password → Input 5-digit user address → Input 4-digit PIN (0001~9999) → Succeeded
Or via 701Client set it on Users screen

E. Arming Password
Access programming mode → 3 Parameters[1] → 8 Arming PWD → Input 4-digit PIN (0001~9999; Default: 1234) → Succeeded
Or via 701Server and set it on AR-829E screen

F. Arming Delay Time

Access programming mode → 3 Parameters[1] → 7 ArmingDelayTm → Enter armed sta. Delay time(Sec) ,Range:000~255；
Armed pulse out-put time. (10ms) ,Range：000~255 → Succeeded

G. Duress Code
Access programming mode → 4 Parameters[2] → 7 Duress Code → 4 sets (select one) → Input 4-digit PIN (0001~9999) → Succeeded
Or via 701Server to set it on AR-829E-V5 screen
※Duress Code is only available in networking mode. It will substitute a personal pin code and send the message of Duress to computer as a
warning signal.
H. Terminal Port
Access programming mode → 5 Tools → 4 Terminal Port → 0:Lift ; 1:Host ; 2:LED ; 3:PRN (default value:1) → Baud Selection
(default value:9600) → Succeeded
I. Setting up the alarm / arming
Conditions:
1. Arming enabled
2.Alarm system connected
Application:
1. Door open too long: Door is open longer than door relay time plus door close time.
2. Force open (Opened without a valid user card): Access by force or illegal procedure.
3. Door position abnormal: When power is off and then on, reader on arming before power off.
Enable/Disable the arming status:
Standby Mode
Card only Card or PIN Card and PIN
Open the door No open the door Input user address → Input 4 Present the tag to reader → Input
Present the tag to reader → Input → Input 4 digits arming PWD digits individual PWD → → 4 digits individual PWD → →
4 digits arming PWD → → Present the tag to reader Input 4 digits arming PWD → Input 4 digits arming PWD →
Access Programming mode
Enable: Access programming mode → 7 Quit & Arming Disable: Access programming mode → 6 Quit

Copyright by SOYAL Technology Co., Ltd.. All rights reserved.

SOYAL
®
AR-829E-V5 V120508
ACCESS CONTROL SYSTEM

J. Anti-pass-back
While connect with AR-721U, AR-737H/U(WG mode) and AR-661U for anti-pass-back function, the access mode needs to be "Card" only.
Device enable
Access programming mode → 4 Parameters[2] → 6 Anti-pass-back → master controller select [1: Yes] → WG select [1: Yes]
Card user enable
Access programming mode → 1 Add/ Delete → 9 Antipass Group → Input 5-digit starting user address → Input 5-digit ending user
address → must select [1: Yes]

K. Lift control
[e.g.] Connect with AR-401RO16B to control which floors the user will be able to access. (BAUD9600)
Setting Lift control
Access programming mode → 5 Tools → 4 Terminal Port → 0：Lift Controller → Baud Selection 0： 9600
Access programming mode → 5 Tools → 5 Terminal Port → 1：Lift Controller
(need to use 725L485)

Set Floor/ Stop

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
1 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 1
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0

Single floor
Access programming mode → 2 User Setting → 4 Single Floor →
Input 5-digit user address → Input single floor number: 1~64

Multi floors
Access programming mode → 2 User Setting → 5 Multi Floor → Input 5-digit user address → Select range: 1 or 2 or 3 or 4 → Input 16 digits
multi floors number [0:disable, 1: enable]
[e.g.] Set NO. 114, can use it with the 8 F and 16F:
Access programming mode → 2 User Setting → 5 Multi Floor → 114 →1 → 0000000100000001

L. Alarm Clock (for Factory)

Access programming mode → 5 Tools → 9 Daily Alarm → Set (00~15) → Set Start Tm (24 Hours) ; Set Effect Sec.
(Seconds as the bell time, Range:1~255) → Set Weekday (0:disable, 1: enable) → Succeeded

Hardware installation

POWER
12VDC
DC 12V Relay Board P1
12V 1
CTL 2
COM 3
N.O. 4
N.C. 5
Mike device 6 ALM
Music Box
Horn Mike's sound wire 7 12V
M2 M1 8 GND
Board
GND
Mike's sound wire
Controller
Music Box
Mike device Output to M1 and M2

M. OpenZone
Access programming mode → 3 Parameters[1] → 2 OnOff OpenZone → Main Controller Auto Open Zone (0:disable,1:enable) →
Open Door Imm. During Open Zone (0:No,1:Yes) → WG1 Port Auto Open Zone (0:disable,1:enable) → Open Door Imm. During
Open Zone (0:No,1:Yes) → Succeeded

N. Open TimeZone
Access programming mode → 5 Tools → 6 Open TimeZone → Set (00~15) → Time (24 Hours) ; Main Port (0:disable, 1: enable) ;
WG Port (0:disable, 1: enable) → Weekday (0:disable, 1: enable) → succeeded

Copyright by SOYAL Technology Co., Ltd.. All rights reserved.

 LCD Access Controller
V120508

Firmware Upgrade

Get the upgrade software from SOYAL or our distributor and run “UdpUpdater” software

Execute the software The software is within SOYAL CD or Login the SOYAL web to downloads

2 4

Update the firmware

[Please login the SOYAL web to download the new ISP Firmware.]
1. Input the Target Address and Port
2. [Load F/W] open the documents that have the new ISP Firmware
3. Click the new ISP Firmware and [Open] it
4. Click [Update F/W] to start the firmware update
5. Till the screen shown [Firmware Update is Complete]

Restoring Factory Settings

Reset all device parameters and user card data
Reset all device parameters and user card data:
Access programming mode → 4 Parameters2 → 9 Factory Reset →0 : System Param ;
1 : User Setting ; 2 : System & User

Reset IP Setting:
When the device's power is on, press the【RESET】button the main board untill the ERR (Red) LED of
screen lights up. (Reference to picture)

※ After operation as above, you will hear the long reminder sound,and wait until the
sound disappear then reset the power of the controller,the device will restore factory setting.

Manu Tree

1. Add/ Delete 2. User Setting 3. Parameters[1] 4. Parameters[2] 5. Tools 6. Quit

1. Add > Card ID 1. Password 1. Node ID 1. Auto Relock 1. Language
2. Add > RF Learn 2. Access Mode 2. OnOff OpenZone 2. Egress(R.T.E) 2. Master Code
3. Suspend > Address 3. Extend Options 3. Door Relay Tm 3. Miscellaneous 3. Master Range
7. Quit & Arming
4. Suspend > ID # 4. Single Floor 4. Door Close Tm 4. Force Open 4. Terminal Port
5. Delete > Address 5. Multi Floor 5. Alarm Relay Tm 5. Close & Stop 5. Ext.Comm Port
6. Delete > ID # 6. Alarm Delay Tm 6. Anti-pass-back 6. Open Time Zone
7. Recover > Address 7. Arming Delay Tm 7. Duress Code 7. Informations
8. Recover > ID # 8. Arming PWD 8. Password Mode 8. Clock Setting
9. Antipass Group 9. Factory Reset 9. Daily Alarm

Copyright by SOYAL Technology Co., Ltd.. All rights reserved.

SOYAL
®
AR-829E-V5 V120508
ACCESS CONTROL SYSTEM

IP Setting

Open your Web Browser and input factory default IP

address: http://192.168.1.127

If the IP address of AR-829E-V5

has changed We must enter the
new IP address.

Page menu

Monitor the on-line computer

IP Setting

Change the Log-in information

Current State
Online Status is able to monitor and
show which computer is linking on Ethernet Module

Show which computer is linking

on Ethernet Module.

Current IP address of the AR-829E-V5

Log-in User Password

When you choose the "Networking Setting" or "User Password" at first.
Log-in window will pop out and please input admin
※ At the Factory Default
User name: admin
Password: No as default value,so please just press “OK” to log-in

Networking Setting
You will find initial IP Address 192.168.1.127 and check
MAC Address is the same as sticker on Ethernet Module
device. Please revise IP address you want, and then click
“Update” button. After updating the IP, please re-connect
the Web Browser by new IP address.

User Password
Change the log-in password to lock the IP setting of
Ethernet Module.
The password composes of 10 characters at most, it can be
either A~Z or 0~9.

Copyright by SOYAL Technology Co., Ltd.. All rights reserved.

 TCP/IP RS-485

System Diagram RS-232 TTL

USB WG

Computer
Application Software
Interface
TCP/IP RS-232 USB GSM USB

HUB 1.Software for 4.Firmware

Security Access Update
or Attendance 701 Server 701 Client VisualProx ISP Tools
INTERNET
GSM MODEM 5.Development,
TCP/IP TCP/IP TCP/IP TCP/IP TCP/IP TCP/IP 2.SOR Applications Monitoring
Software
SOR Tools Mifare Key Comm View

3.Software for 6.Programmable

Converter Software
GSM MODEM Programmer Networking or
AR-727CM AR-701CM AR-321CM AR-737P NET 727 Web NODE 737
Computer-Aided
device setting Software AR-401E
(AR-727i V1) (AR-727i V2)
RS-485 RS-485 RS-485 RS-485
(Ethernet) Up to 254 nodes Up to 254 nodes Up to 254 nodes Up to 254 nodes
Multi-Door
Networking
Controller
AR-716Ei
(RS-485)
Multi-Door
Networking
Controller

(RS-485) AR-716E
Access Controller RS-485 (CH1) RS-485 (CH2)
(Up to 8 nodes) (Up to 8 nodes)
AR-727H

Copyright
(Ethernet) AR-723H AR-727HTTL AR-829E/V5 AR-725H-M AR-327H AR-721H AR-821EF/V5
Access Controller
RS-485 TTL TTL WG WG WG WG WG1 WG2
AR-725E-M/V2 AR-821EVi/V5 AR-881EV AR-881EF

Converter AR-721H AR-737H AR-725H-M AR-331H AR-727H AR-321H

AR-321DAX1 AR-321L485 AR-321L485
WG TTL WG WG
RS-485 RS-485 RS-485 RS-485

(Wiegand)
Access Reader
LCD Access Controller

AR-725U-M AR-721K AR-737U AR-661U AR-725U-M AR-721U AR-725U-M AR-725K-M AR-737U

DO

Door Open
AR-321W AR-PB-323 Relay output
Room control Neworking
systems LED Display
DI
Diagram of Electric Lock Door Sensor
Basic
application
AR-PB-321 AR-323D of single
door DO

AR-725H-M Push Button AR-721U

Exit Entrance
DO DI
Programmable
Controller/ Elevator Alarm WG
Lift Controller AR-401Ei AR-401E AR-401RO16B
AR-401DI16 AR-401DI16 16-Levels Lift (Lift Control)
AR-401RO16 AR-401RO16 Controller

by SOYAL Technology Co., Ltd.. All rights reserved.

V120508