11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

Page 1

WDZ-5211 line protection measurement and control device (V1.07)

WDZ-5211 line protection measurement and control device

1 device function

WDZ-5211 line protection measurement and control device is mainly used for the protection and measurement and control of 10KV and below feeders.

WDZ-5200 series line protection device includes WDZ-5215 short line comprehensive protection and monitoring device.

The difference of measurement and control functions is shown in the table below.

WDZ-5211 WDZ-5215
Differential quick break protection √
Ratio differential protection √

CT disconnection alarm √ √
Low voltage blocking over current one-stage protection
√ √
Low voltage blocking overcurrent two-stage protection
√ √
Three-stage overcurrent protection √ √
Post-accelerated protection √ √
Overload protection √ √
Ground protection section √ √
Two-stage grounding protection √ √

PT disconnection alarm √ √
Measurement function √ √
control function √ √
Hardware energy metering function √ √
Operating circuit function √ √

2 channels 4～20mA output √ √

2 Protection function and principle

2.1 Over-current protection

Over-current protection for one stage can be set via low-voltage lockout, when any one of the three line voltages is less than the low-voltage lockout

Value, open the over-current one-stage protection through low voltage blocking.

2.1.1 Block diagram of protection action logic

Page 1 of 20

Page 2

WDZ-5211 line protection measurement and control device (V1.07)

https://translate.googleusercontent.com/translate_f 1/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle
2.1.2 Protection action criterion
⎧I > I
⎪ max gl 1

⎨tt > gl 1
⎪
⎩U min < U dybs

In the formula, I max : A, B, C phase current (I a , I b , I c ) maximum value (A)

I a : A phase current value (A)

I b : B-phase current value (A)

I c : C-phase current value (A)

U min：The minimum value of AB, BC, CA line voltage (U ab , U bc , U ca ) (V)

U ab : AB line voltage (V)

U bc : BC line voltage (V)

U ca : CA line voltage (V)

I gl1：The setting value of over-current protection action current (A)

t gl1：The setting value of over-current protection action time for one stage (s)

U dybs : Low voltage blocking overcurrent voltage setting value (V)

2.2 Two-stage overcurrent protection

Over-current two-stage protection can be set to be locked by low voltage, when any one of the three line voltages is less than the low voltage, it can be locked

Value, open the over-current two-stage protection through low voltage blocking.

2.2.1 Block diagram of protection action logic

2.2.2 Protection action criterion

⎧I > I
⎪ max gl 2

>
⎨tt gl 2
⎪
⎩U min < U dybs
In the formula, I gl2 : overcurrent two-stage protection action current setting value (A)

t gl2 : the setting value of the second- stage overcurrent protection action time (s)

Page 2 of 20

Page 3

WDZ-5211 line protection measurement and control device (V1.07)

2.3 Three-stage overcurrent protection

2.3.1 Block diagram of protection action logic

2.3.2 Protection action criterion

⎪I max > I gl 3
⎧
⎨
⎩tt > gl 3
⎪

In the formula, I gl3 : overcurrent three-stage protection action current setting value (A)

https://translate.googleusercontent.com/translate_f 2/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

t gl3：The setting value of overcurrent three-stage protection action time (s)

2.4 After acceleration protection

In order to prevent the auxiliary power switch from being switched on to the faulty line, the device provides post-acceleration protection. The post-acceleration signal supports

Signal input and pulse signal input, after the acceleration protection is turned on for 5 seconds.

2.4.1 Block diagram of protection action logic

2.4.2 Protection action criterion

⎧I >I
max hjs
⎪
>
⎨tt hjs
⎪
⎩Post-accelerated
open
protection
In the formula, I hjs : the setting value of the operating current of the back acceleration protection (A)

t hjs：The setting value of the post acceleration protection action time (s)

2.5 Overload protection

Overload protection provides options for definite time, normal inverse time, very inverse time, and abnormal inverse time. Inverse time curve symbol

Comply with IEC 60255-3 standard.

Page 3 of 20

Page 4

WDZ-5211 line protection measurement and control device (V1.07)

2.5.1 Protection action logic block diagram

Trip
≥1

Signal

Warn

2.5.2 Action criterion of definite time protection

⎪I max > I gfh

⎧
⎨
⎩tt > gfh
⎪

In the formula, I gfh : overload protection action current setting value (A)

t gfh : setting value of overload protection action time (s)

2.5.3 Normal inverse time protection action criterion

⎧I > I
max gfh
⎪
⎪ > 14.0 Xt
⎨t gfh
⎛ ⎞02.0
⎪ I
⎜ max ⎟ −
⎪ ⎜ ⎟ 1
⎩ ⎝ I gfh ⎠

2.5.4 Action criterion for very inverse time protection

⎧I > I
max gfh
⎪
⎪
⎨
https://translate.googleusercontent.com/translate_f 3/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

⎨t > 5.13 X t gfh

⎪
⎪ I max −
⎪ 1
⎩ I gfh

2.5.5 Action criterion of abnormal anti-time limit protection

⎧I > I
max gfh
⎪
⎪ > 80 Xt
⎨t 2 gfh
⎪ ⎛ ⎞
⎜I max ⎟ −
⎪ ⎜ ⎟ 1
⎩ ⎝ I gfh ⎠

2.6 Grounding protection section

The zero-sequence current is obtained through a special zero-sequence current transformer, and the two-stage zero-sequence overcurrent protection is used to achieve the purpo

of. The measuring range of the external zero sequence current of the device is 10mA～6A.
• • • •

If there is no external dedicated zero-sequence current transformer, the device 3

can = IIIa +zero-sequence
I 0produce b
+ c . Device
by software,

Page 4 of 20

Page 5

WDZ-5211 line protection measurement and control device (V1.07)

If there is a CT disconnection, the self-produced zero sequence is instantly blocked to prevent the self-produced zero sequence malfunction caused by the CT disconnection. To prev

The unbalanced current caused by the inconsistent sensor characteristics causes the grounding protection to malfunction, and the maximum phase current I max is used as the braking a

The protection action curve is shown in the figure below.

I 0 /I 0dz

0 1.05 I max /I e

Action curve of grounding protection with phase current brake

2.6.1 Block diagram of protection action logic

Zero-sequence over-current logic, suitable for zero-sequence current external connection occasions:

With phase current braking logic, suitable for zero-sequence current self-produced occasions:

2.6.2 Protection action criterion

Zero sequence overcurrent:

⎧I > I
⎨ 0 01 dz

⎩tt >
https://translate.googleusercontent.com/translate_f 4/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle
0 01 dz

Phase current brake:

Page 5 of 20

Page 6

WDZ-5211 line protection measurement and control device (V1.07)

⎧I > I I max ≤ 05.1 I e

0 01 dz
⎪
⎨I 0 > [1 + (I max I e − 405.1) ]I 01 dz
I
max
> 05.1 I
e
⎪ >
⎩tt0 01 dz

In the formula, I 01dz : Zero-sequence protection one-stage action current setting value (A)

t 01dz：The setting value of a period of action time of zero sequence protection (s)

I e：The secondary value of the rated current of line operation (A)

2.7 Two-stage grounding protection

2.7.1 Block diagram of protection action logic

Zero-sequence over-current logic, suitable for zero-sequence current external connection occasions:

Trip
t 02dz
Signal

t 02dz Warn

With phase current braking logic, suitable for zero-sequence current self-produced occasions:

&
Trip
t 02dz
≥1
Signal
&
&

t 02dz Warn

CT disconnection

2.7.2 Protection action criterion

Zero sequence overcurrent:

⎧I > I
0 02 dz
⎨
⎩tt0 > 02 dz

Phase current brake:

⎧I > I I max ≤ 05.1 I e

⎪ 0 02 dz

⎨I 0 > [1 + (I max I e − 405.1) ]I 02 dz I

max
> 05.1 I
e
⎪ >
⎩tt0 02 dz

In the formula, I 02dz : the setting value of the second-stage operating current of the zero sequence protection (A)

t 02dz : the setting value of the second-stage action time of zero sequence protection (s)

I e：The secondary value of the rated current of line operation (A)

2.8 Instantaneous CT disconnection lockout function

The CT disconnection discrimination is based on the following assumptions:

(1) CT disconnection does not happen at the same time;

Page 6 of 20

Page 7

WDZ-5211 line protection measurement and control device (V1.07)

https://translate.googleusercontent.com/translate_f 5/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

(2) CT disconnection and failure do not occur at the same time.

If any of the following conditions is met, the CT disconnection judgment is not performed:

(1) The maximum phase current before starting is less than 0.2Ie, the CT disconnection judgment is not performed;

(2) The maximum phase current after starting is greater than 1.2Ie;

(3) The current after starting is higher than before starting;

Only after the self-produced zero-sequence components act, it enters the instantaneous CT disconnection discrimination program.

If the current meets the following conditions at the same time, it is considered that the CT is disconnected:　

(1) Only one-phase or two-phase current is zero;

(2) The other two-phase or one-phase current is equal to the current before starting;

2.9 Delayed CT disconnection alarm function

The time-delay CT disconnection discrimination logic is: three-phase current, one-phase or two-phase current is less than 0.125 times the rated current, and others

If the two-phase or one-phase current is greater than 0.2 times the rated current, and if this condition is met for more than 2 seconds, a CT disconnection alarm will be issued

Signal, but does not block any protection.

2.10 PT disconnection

The device is equipped with a delay PT disconnection alarm function.

PT disconnection is divided into three-phase PT disconnection and single-phase or two-phase PT disconnection. The main feature of a three-phase PT disconnection is that the
The main feature of single-phase or two-phase PT disconnection is the large unbalanced voltage, which is judged by the negative sequence voltage.

2.10.1 Block diagram of protection action logic

2.10.2 Protection action criterion

⎧I > 2.0 I
⎨ max e

⎩U max < 30 V

{U 13 V
2 >

2.11 Protection setting

Serial number Name and meaning symbol unit Setting range

1 Rated circuit current Ie A 0.20In-1.20In

2 Low voltage lockout value U dybs V 10.00-90.00
3 Over-current protection current I gl1 A 0.20In-20.00In

4 Over-current for a period of action

t gl1time s 0.00-10.00

Page 7 of 20

Page 8

WDZ-5211 line protection measurement and control device (V1.07)

5 Low-voltage blocking over-current section Exit, invest

6 Overcurrent two-stage protectionI current

gl2 A 0.20In-20.00In
7 Overcurrent two-stage action time
t gl2 s 0.10-100.00

8 Low-voltage blocking over-current second stage Exit, invest

9 Overcurrent three-stage protection current A

I gl3 0.20In-20.00In
10 Over-current three-stage action time
t gl3 s 0.10-100.00
11 After acceleration protection current
I hjs A 0.20In-20.00In

12 Back acceleration time t hjs s 0.00-4.90

13 Overload protection current I gfh A 0.20In-20.00In
14 Overload operating time t gfh s 0.10-650.00
Definite time/normal inverse time limit/

https://translate.googleusercontent.com/translate_f 6/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle
15 Overload action curve Very inverse time limit/extraordinary
time limit

16 Overload protection outlet method Alarm, trip

①
17 Zero-sequence action one-stage Icurrent
01dz A 0.010-6.000

18 Zero sequence protection for a period

t 01dz of times 0.00-10.00
19 Grounding one-stage exit method Alarm, trip
②
20 Zero-sequence action two-stage Icurrent
02dz A 0.010-6.000
twenty one Zero sequence protection for twot 02dz
periods of time
s 0.10-100.00

twenty two Two-stage grounding outlet method Alarm, trip

Note: ①②The fixed value range of the first-stage current of zero-sequence action and the second-stage current of zero-sequence action: when the zero-sequence current is ext
0.010-6.000A; 0.20In-20.00In in the case of zero-sequence current self-production. The access method of zero sequence current is selected in "Installation
Settings menu -> fixed value settings -> system settings -> engineering parameters -> zero sequence current access mode" to configure.

2.12 Soft pressure plate

The device provides the function of the soft pressing plate, and the virtual remote signal displacement information of the soft pressing plate will be generated in the process of

Serial number Name and meaning symbol Setting range

1 Overcurrent protection Exit, invest

2 Overcurrent two-stage protection Exit, invest

3 Three-stage overcurrent protection Exit, invest

4 Post-accelerated protection Exit, invest

5 Overload protection Exit, invest

6 Ground protection section Exit, invest

7 Two-stage grounding protection Exit, invest

8 CT disconnection alarm Exit, invest

9 PT disconnection alarm Exit, invest

3 Measurement and control function

3.1 Measurement function

Three-phase voltage, three-phase current, active power, reactive power, power factor, frequency.

Page 8 of 20

Page 9

WDZ-5211 line protection measurement and control device (V1.07)

3.2 Open in

Provide standard 24-way open access.

3.3 out

Provides standard 5 relay outputs with 7 open contacts.

3.4 Remote control

Provide remote tripping and closing operations of the circuit breaker switch.

3.5 Metering function

Provide hardware forward active power, forward reactive power, reverse active power, reverse reactive power measurement functions, and provide forward active power,

Positive reactive energy pulse output function.

At the same time, the active and reactive power calculated by the device can be used to accumulate active and reactive energy.

3.6 Operating circuit

Operating loop functions include jump circle, close circle, jump position monitoring, close position monitoring, jump position signal output, close position signal output,

Control circuit disconnection output, protection trip output, remote control trip output, remote control close output, manual trip input, manual close

Trip input, DCS trip input, protection trip input, 2-way position combined trip or protection combined trip output, etc.

3.7 DCS output

The device provides 1 channel of 4-20mA output, optional 2 channels of 4-20mA output, and the corresponding measurement can be arbitrarily set

Amount and multiple.

https://translate.googleusercontent.com/translate_f 7/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle
4 Backplane terminal and wiring schematic diagram

4.1 Analog input

U a , U b , and U c are bus voltages, which are input together as protection and measurement voltages in the device, line voltage is connected, and rated voltage

The voltage is 100V.

I A , I B , and I C are measurement currents, which need to be input from the dedicated measurement CT. The measuring current is divided into rated 5A and 1A.

I a , I b , and I c are three-phase protection currents. The protection current is divided into rated 5A and 1A.

3I 0 is the zero-sequence current, which is connected from a dedicated zero-sequence current transformer. The effective measuring range of the secondary value of zero sequen

6A. If there is no special zero-sequence current transformer, the device can also produce zero-sequence by itself

4.2 Backplane terminal

Viewed from the front of the device, the leftmost terminal on the back panel is slot 1, the rightmost is slot 5, and the middle is slot 2, slot 3,

Slot 4. From the back of the device, slot 1 is on the far right, and slot 5 on the far left.

The terminal number is 3 digits, such as "ABC", the first digit A is the slot number, and the second three digits BC are the top-down terminals

The serial number. For example, the first terminal of slot 3 is numbered 301.

4.2.1 Basic configuration terminal of operation panel

Page 9 of 20

Page 10

WDZ-5211 line protection measurement and control device (V1.07)

https://translate.googleusercontent.com/translate_f 8/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

Slot 1 : Molded into the board

Terminals 101, 103, 105 are line voltage inputs.

Terminals 107～108 are input for measuring phase A current.

Terminals 109～110 are input for measuring phase B current.

Terminals 111～112 are input for measuring phase C current.

Page 10 of 20

Page 11

WDZ-5211 line protection measurement and control device (V1.07)

Terminals 113～114 are used to protect the A-phase current input.

Terminals 115～116 are used to protect phase B current input.

Terminals 117～118 are used to protect phase C current input.

Terminals 119～120 are zero sequence current 3I 0 input.

Slot 2 : Empty board

Slot 3 : Operation board

Terminals 301~303 are position status output. 302～301 are the status output of the jump position; 303～301 are the status of the closed position

Output.

Terminals 304～305 are the control circuit disconnection output.

Terminal 306 is the negative terminal of the close monitoring relay.

Terminal 307 is the negative terminal of the trip monitoring relay.

Terminal 308 is a protective trip outlet (BTJ), which can be connected to terminal 318 via a pressure plate or directly.

Terminal 309 is the remote control positive power input terminal, only when it is connected to the positive power, the device will remote jump and remote close function

Invest.

Terminal 310 is the remote control closing outlet (YHJ), which can be connected to terminal 317 via a pressure plate or directly.

Terminal 311 is a remote control trip outlet (YTJ), which can be connected to terminal 319 via a pressure plate or directly.

Terminal 312 is the control positive power input terminal.

Terminal 313 is the control negative power input terminal.

The terminal 314 is connected to the external closing mechanism, namely the circuit breaker closing coil.

Terminal 315 is connected to an external trip mechanism, that is, the circuit breaker trip coil.

Terminal 317 is the input terminal for manual closing.

Terminal 318 is the protection trip input terminal.

Terminal 319 is the manual trip input terminal.

Terminal 320 is the DCS trip input terminal.

Terminals 321～322 are output 4, the default is the protection joint jump outlet, and it can also be selected as the position joint jump through the jumper.

Terminals 323～324 are output 5, the default is the protection joint jump outlet, and it can also be selected as the position joint jump through the jumper.

Terminals 325 to 326 are device failure alarm signal output.

Terminals 327～328 are protection trip signal output.

Terminals 329～330 are protection alarm signal output.

Terminals 331～332 are the action alarm signal output, when the protection action or protection alarm, this signal is output.

Slot 4 : Interface board

Terminals 401～402 are fieldbus 1 input, 401 is positive polarity, and 402 is negative polarity. Can choose CAN,

ProfiBus network interface.

Terminal 403 is the signal ground.

Terminals 404～405 are fieldbus 2 inputs, 404 is positive polarity, and 405 is negative polarity. Can choose CAN,

Page 11 of 20

Page 12
https://translate.googleusercontent.com/translate_f 9/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

WDZ-5211 line protection measurement and control device (V1.07)

ProfiBus network interface.

Terminals 406～407 are GPS time synchronization input ports, connected to 485 differential level.

The terminal 408 is the signal ground.

Terminals 410～411 are active energy pulse output, 24V passive empty contact output. 410 is positive, 411 is negative

end.

Terminals 412～413 are reactive energy pulse output, 24V passive empty contact output. 412 is positive, 413 is negative

end.

Terminals 414～416 are 2 channels of 4～20mA output. 414～4165 is the first output, 414 is the positive end, 416

It is the negative terminal; 415～416 are the second output, 415 is the positive terminal, and 416 is the negative terminal.

The device grounding stud must be reliably connected to the site grounding grid.

Slot 5 : Power Board

Terminal 501 is the power ground of the device. After this terminal is connected to the device grounding stud, it is reliably connected to the field grounding grid.

Terminals 503 ~ 504 are the device power input, and the device power can be AC ​or DC 220V or DC 110V. 503

Is the negative input terminal of the device power supply, and 504 is the positive input terminal of the device power supply.

Terminals 506～530 are 24 channels of high-current DC 110V or 220V input. 506 is the open input common negative terminal, 507～

530 is 24 input channels. 509 is defined as the back acceleration contact by default.

Terminals 531～532 are device lockout outputs, normally closed contacts. The 24V power failure of the device or the abnormal operation of the internal CPU

Operation, the contact is closed.

4.2.2 Do not configure the basic configuration terminal of the operation panel

Page 12 of 20

Page 13

WDZ-5211 line protection measurement and control device (V1.07)

https://translate.googleusercontent.com/translate_f 10/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

Slot 1 : Molded into the board

Same as the operation board configuration, the lower mold inserts the board terminal description.

Slot 2 : Empty board

Slot 3 : Exit board

Terminals 301～304 are protection combined jump output. 301～302 are one of the secondary contact outputs; 303～304 are among them

Page 13 of 20

Page 14

WDZ-5211 line protection measurement and control device (V1.07)

Another contact output.

Terminals 305～308 are 2 exits. 305～306 are one of the secondary contact outputs; 307～308 are the other

One contact output.

Terminals 309～310 are protection trip outlets.

Terminals 311 to 312 are remote relay outlets.

Terminals 313～314 are remote relay outlets.

Terminals 325 to 326 are device failure alarm signal output.

Terminals 327～328 are protection trip signal output.

Terminals 329～330 are protection alarm signal output.

Terminals 331～332 are the action alarm signal output, when the protection action or protection alarm, this signal is output.

Slot 4 : Interface board

Description of the interface board terminals under the same operation board configuration.

Slot 5 : Power Board

510 is defined as the remote position, and 511 and 512 are defined as the circuit breaker tripping and closing access (510, 511, 512 default

If it is undefined, it needs to be set in the factory settings). The rest is the same as the description of the power supply board terminals under the operation board configuration.

4.3 Terminal wiring schematic diagram

4.3.1 Analog input wiring schematic diagram

1LHa

https://translate.googleusercontent.com/translate_f 11/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle
Save
113 114
1LHb
Protect

Electricity
115 116
Electricity
1LHc
flow
UA mother
117 118 Electricity
101
String

Pressure
LH0 flow
UB String

Zero sequence 103 Back to

119 120 Electricity
Current
road
UC Pressure

105
2LHa Back to

107 108

2LHb
Measurement
road
109 110
quantity
2LHc

Electricity

111 112
flow

Page 14 of 20

Page 15

WDZ-5211 line protection measurement and control device (V1.07)

4.3.2 Wiring schematic diagram of binary input, central signal, network, analog output, electric energy pulse output circuit

-KM +KM
Small bus
531
3 1 Device lockout
1Q air switch
4 2 532

Pack 325
Device failure
L/DC+ middle
Set 326
504
Electricity
Central
L/DC- 327
503 source Protection action
letter
328
Open into 1
507 No
329
Open in 2 Protection alarm
508
330
Post-acceleration
509
331
remote Action warning signal
Note 1 distance
510 332
Jump
511
NET1-A
In position 401
512
Fieldbus 1
letter NET1-B
Open into 7
513 402

Open into 8 Signal ground

514
403 Pass
Open into 9
515 quantity NET2-A News
404 Fieldbus 2
Open into 10
516 net
NET2-B
Open into 11 405 Network
517
Pick GPS+
Open into 12
518 406

Open into 13
519 GPS- GPS time synchronization
407
Open into 14
520
set Signal ground
Open 15 408
521

Open into 16
522
Note
Active pulse output+ Electricity
410
Open into 17
523
Spend
Open into 18 Active pulse output-
524 411 pulse

Open into 19
525 Reactive pulse output+ rush
412
Open into 20 lose
526
413 Reactive pulse output-
Open into 21 out
527 Note 3

Open into 22 Analog output 1 mold

528 414
To be
Open into 23
529 Analog output 2 quantity
415
Open into 24 lose
530
Output common
416 out
Open into the public
506

Note 1: If the operation panel is configured, the remote, close, and jump signals do not need to be connected.

Note 2: The electrical energy pulse output is 24V empty contact output, passive.
Note 3: R is an external resistance, which should be less than 500 ohms, 250 ohms are recommended.

https://translate.googleusercontent.com/translate_f 12/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

Page 15 of 20

Page 16

WDZ-5211 line protection measurement and control device (V1.07)

4.3.3 Schematic diagram of the operation circuit of the operation panel

301 Tab output

302
Closed output
303

304 Control loop

Disconnected
305

321
Out of 4
322

323
Out of 5
324

4.3.4 Schematic diagram of open loop wiring without operating panel

301

302 Protection joint jump

Jump
303

304
combine
305

306 Out 2

307 brake

308

309 Protection trip

out
310

311 Teleconnection

312 mouth

313 Remote jump

314

Page 16 of 20

https://translate.googleusercontent.com/translate_f 13/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

Page 17

WDZ-5211 line protection measurement and control device (V1.07)

5 Device selection

WDZ-5211

Network Configuration
1: CAN network
2: ProfiBus network

Power board configuration

0: No power
1: There is power

Operating circuit configuration

0: No operating circuit
1: Operating circuit, anti-jumping
2: Operating circuit, no anti-jumping

DC power supply
1: DC power supply 110V
2: DC power supply 220V

Secondary rated current

1: Secondary current In 1A
5: Secondary current In 5A

(1) The device network communication interface can be equipped with CAN and ProfiBus, both of which are dual-network configuration; if you need to choose an RS485 interface,

Please specify;

(2) The device can be equipped with a hardware power board;

(3) The device can be equipped with an operating circuit, and the anti-jumping function can be canceled; the combined trip relay defaults to the protection combined trip, if the comb

The relay needs to be connected to the position, please give special instructions; the operating circuit tripping and closing current defaults to 0.3~4A self-adaptive, such as

If the tripping and closing current is 0.05~0.3A or 4~10A, please specify. The operation circuit can also be omitted;

(4) The operating circuit power supply and the input power supply of the device are divided into DC 110V and DC 220V; the device power supply does not distinguish between 110V

And 220V, do not distinguish between AC and DC;

(5) The secondary rated current of the device is divided into 1A and 5A. This current is the protection current and the measurement current, and the protection current and the measu

The measuring current is 1A or 5A;

(6) The device is configured with 1 4~20mA output by default, if 4~20mA output is not needed or 2 4~20mA outputs are needed,

Please specify;

(7) The precise working range of the device's zero-sequence CT is 10mA~6A. If the zero-sequence current is not in this range, please specify;

(8) The secondary rated voltage of the device is 100V, 50Hz, and the line voltage is connected;

(9) The device can expand the input and output resources, please specify.

6 Setting instructions

6.1 Important notice

This setting description is for reference only.

Page 17 of 20

Page 18

WDZ-5211 line protection measurement and control device (V1.07)

6.2 One-stage overcurrent protection

6.2.1 Overcurrent protection current I gl1

(1) Calculated based on the three-phase short-circuit current evading the end of the cable, namely

)3(
Operating current
I gl=1 IKrel fK .

K sen = 866.0 )3(I ik. / I op ≥ 2

)2(
Sensitivity coefficient

https://translate.googleusercontent.com/translate_f 14/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle
In the formula, K rel : reliability coefficient, taking 1.2~1.25

)3(
I : . The
fk secondary value of the three-phase short-circuit current at the end of the cable (A)

)3(
I :. The
ik secondary value of the three-phase short-circuit current at the beginning of the cable (A)

)2(
K sen
: Sensitivity at the beginning of the cable when two phases are short-circuited

If the cable length is long and it is not easy to meet the sensitivity requirements, consider adopting voltage blocking quick-break protection.

(2) Current components are calculated based on the short-circuit at the end of the cable with sufficient sensitivity, while voltage components are calculated based on the three-phase s

)2( )2(
Operating current
I gl=1 I fK. / sen
K

= * ZL
Operating voltage perU
unit value
K rel ( X S + X L )
dybs

In the formula,
I : . The
fk
)2(secondary value of two-phase short-circuit current at the end of the cable (A)

Z L : cable line impedance per unit value

X S : 6KV/10KV busbar system reactance standard unit value

X L：The standard unit value of the reactance of the cable line

6.2.2 Over-current operation time t gl1

Generally take t gl1 = 0

6.3 Two-stage overcurrent protection

6.3.1 Two-stage overcurrent protection current I gl2

(1) Calculated by avoiding the self-starting current of the motor, namely

I gl IKrel / n TA
2 = st . all

In the formula, K rel : reliability coefficient, taking 1.15~1.2

I at.all : Self-starting current of the motor connected to the feeder (A)

n TA：current transformer transformation ratio

(2) Cooperate with the calculation of the setting value of the maximum quick-break current of the next-level equipment, namely

I gl IKrel / n TA
2 = op max.

Page 18 of 20

Page 19

WDZ-5211 line protection measurement and control device (V1.07)

In the formula, K rel : reliability coefficient, taking 1.15~1.2

I op.max : the setting value of the maximum quick-break current of the next-level equipment (A)
If the sensitivity is sufficient, try to use a larger operating current

6.3.2 Overcurrent second stage action time t gl2

(1) Cooperate with the next level of quick-break protection, namely

t gl 2 = 0 + Δ t = Δ t

In the formula, t Δ : time level difference, 0.3s can be taken

(2) Cooperate with the next level of over-current protection, namely

t gl 2 = max.
t gl + Δt

In the formula, t Δ : time level difference, 0.3s can be taken

6.4 Three-stage overcurrent protection

Generally three-stage overcurrent protection can not be used

6.5 After acceleration protection

6.5.1 After acceleration protection current I hjs

https://translate.googleusercontent.com/translate_f 15/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle
(1) Calculated according to the self-starting current that dodges the motor
(2) Calculated by avoiding the magnetizing inrush current of the transformer on the line

6.5.2 Post-acceleration action time t hjs

Generally, t hjs =0

6.6 Overload protection

6.6.1 Overload protection current I gfh

It is possible to take I gfh = (1.15~1.3) I e

6.6.2 Overload action time t gfh

Take t gfh =5~10s, act on signal

6.7 Grounding protection

The neutral point is set as follows through the low resistance grounding system:

6.7.1 Zero sequence action current I 0dz

(1) Calculate based on the single-phase grounding current flowing through the protection installation when avoiding the single-phase grounding outside the area:

)1(
I 0=dz IKrel K

In the formula, K rel : Reliability coefficient, take 2~2.5 when protection action is signal, take 2.5~3 when protection action is trip

)1(
I K: Single-phase grounding current supplied by the protected equipment to the short-circuit point when single-phase grounding (A)

Page 19 of 20

Page 20

WDZ-5211 line protection measurement and control device (V1.07)

(2) Coordination calculation with the next level of single-phase grounding protection:

I 0=dz IKrel max..0

op

In the formula, K rel : reliability coefficient, taking 1.1~1.15

I 0.op.max : the maximum operating current of the next-level single-phase grounding protection (A)
The zero sequence action current takes the larger value of a) and b).

6.7.2 Zero sequence action time t 0dz

Coordination calculation with the longest action time of the next level single-phase grounding protection

t 0 dz = tmax..0op + Δt .

In the formula, t 0.op.max : the longest action time of the next level of single-phase grounding protection (s)

t Δ : time difference, 0.3~0.4s

https://translate.googleusercontent.com/translate_f 16/17
11/19/21, 10:12 AM WDZ-5211 line protection measurement and control device 1 device function 2 protection function and principle

Page 20 of 20

https://translate.googleusercontent.com/translate_f 17/17