LM393, LM293, LM2903,

LM2903V, NCV2903

Low Offset Voltage

Dual Comparators
The LM393 series are dual independent precision voltage
comparators capable of single or split supply operation. These devices http://onsemi.com
are designed to permit a common mode range−to−ground level with
single supply operation. Input offset voltage specifications as low as
2.0 mV make this device an excellent selection for many applications
in consumer, automotive, and industrial electronics.
PDIP−8
Features N SUFFIX
8 CASE 626
• Wide Single−Supply Range: 2.0 Vdc to 36 Vdc 1
• Split−Supply Range: ±1.0 Vdc to ±18 Vdc
• Very Low Current Drain Independent of Supply Voltage: 0.4 mA SOIC−8
D SUFFIX
• Low Input Bias Current: 25 nA 8
CASE 751
• Low Input Offset Current: 5.0 nA
1

• Low Input Offset Voltage: 5.0 mV (max) LM293/393 Micro8

• Input Common Mode Range to Ground Level 8 DM SUFFIX
CASE 846A
• Differential Input Voltage Range Equal to Power Supply Voltage 1

• Output Voltage Compatible with DTL, ECL, TTL, MOS, and CMOS
Logic Levels
PIN CONNECTIONS
• ESD Clamps on the Inputs Increase the Ruggedness of the Device
without Affecting Performance Output A 1 8 VCC
• NCV Prefix for Automotive and Other Applications Requiring Site 2
−
7 Output B
Inputs A +
and Control Changes 3
−
6
Inputs B
•
+ 5
Pb−Free Packages are Available GND 4

(Top View)
VCC + Input − Input Output

R2 DEVICE MARKING & ORDERING

2.1 k INFORMATION
Q4 See detailed ordering and shipping information and marking
R4 Q5 Q6 information in the package dimensions section on pages 6
Q3 Q14
2.0 k and 7 of this data sheet.

F1

Q10
Q1 Q9 Q16
Q8 Q12
Q2 Q15
Q11
R1
4.6 k

Figure 1. Representative Schematic Diagram

(Diagram shown is for 1 comparator)

 Semiconductor Components Industries, LLC, 2004 1 Publication Order Number:

October, 2004 − Rev. 15 LM393/D
 LM393, LM293, LM2903, LM2903V, NCV2903

MAXIMUM RATINGS
Rating Symbol Value Unit
Power Supply Voltage VCC +36 or ±18 Vdc
Input Differential Voltage Range VIDR 36 Vdc
Input Common Mode Voltage Range VICR −0.3 to +36 Vdc
Output Short Circuit−to−Ground ISC Continuous mA
Output Sink Current (Note 1) ISink 20
Power Dissipation @ TA = 25°C PD 570 mW
Derate above 25°C 1/RJA 5.7 mW/°C
Operating Ambient Temperature Range TA °C
LM293 −25 to +85
LM393 0 to +70
LM2903 −40 to +105
LM2903V, NCV2903 (Note 2) −40 to +125

Maximum Operating Junction Temperature TJ(max) °C

LM393, 2903, LM2903V 150
LM293, NCV2903 150

Storage Temperature Range Tstg −65 to +150 °C

ESD Protection at any Pin Vesd V
− Human Body Model 2000
− Machine Model 200

Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC, output short circuits to VCC can cause
excessive heating and eventual destruction.
2. NCV2903 is qualified for automotive use.

http://onsemi.com
2
 LM393, LM293, LM2903, LM2903V, NCV2903

ELECTRICAL CHARACTERISTICS (VCC = 5.0 Vdc, Tlow ≤ TA ≤ Thigh, unless otherwise noted.)
LM2903, LM2903V,
LM293, LM393 NCV2903

Characteristic Symbol Min Typ Max Min Typ Max Unit

Input Offset Voltage (Note 4) VIO mV
TA = 25°C − ±1.0 ±5.0 − ±2.0 ±7.0
Tlow ≤ TA ≤ Thigh − − 9.0 − 9.0 15
Input Offset Current IIO nA
TA = 25°C − ±5.0 ±50 − ±5.0 ±50
Tlow ≤ TA ≤ Thigh − − ±150 − ±50 ±200
Input Bias Current (Note 5) IIB nA
TA = 25°C − 25 250 − 25 250
Tlow ≤ TA ≤ Thigh − − 400 − 200 500
Input Common Mode Voltage Range (Note 5) VICR V
TA = 25°C 0 − VCC −1.5 0 − VCC −1.5
Tlow ≤ TA ≤ Thigh 0 − VCC −2.0 0 − VCC −2.0
Voltage Gain AVOL 50 200 − 25 200 − V/mV
RL ≥ 15 k, VCC = 15 Vdc, TA = 25°C
Large Signal Response Time − − 300 − − 300 − ns
Vin = TTL Logic Swing, Vref = 1.4 Vdc
VRL = 5.0 Vdc, RL = 5.1 k, TA = 25°C
Response Time (Note 7) tTLH − 1.3 − − 1.5 − s
VRL = 5.0 Vdc, RL = 5.1 k, TA = 25°C
Input Differential Voltage (Note 8) VID − − VCC − − VCC V
All Vin ≥ GND or V− Supply (if used)
Output Sink Current ISink 6.0 16 − 6.0 16 − mA
Vin ≥ 1.0 Vdc, Vin+ = 0 Vdc, VO ≤ 1.5 Vdc TA = 25°C
Output Saturation Voltage VOL mV
Vin ≥ 1.0 Vdc, Vin+ = 0, ISink ≤ 4.0 mA, TA = 25°C − 150 400 − − 400
Tlow ≤ TA ≤ Thigh − − 700 − 200 700
Output Leakage Current IOL nA
Vin− = 0 V, Vin+ ≥ 1.0 Vdc, VO = 5.0 Vdc, TA = 25°C − 0.1 − − 0.1 −
Vin− = 0 V, Vin+ ≥ 1.0 Vdc, VO = 30 Vdc,
Tlow ≤ TA ≤ Thigh − − 1000 − − 1000
Supply Current ICC mA
RL = ∞ Both Comparators, TA = 25°C − 0.4 1.0 − 0.4 1.0
RL = ∞ Both Comparators, VCC = 30 V − − 2.5 − − 2.5
LM293 Tlow = −25°C, Thigh = +85°C
LM393 Tlow = 0°C, Thigh = +70°C
LM2903 Tlow = −40°C, Thigh = +105°C
LM2903V & NCV2903 Tlow = −40°C, Thigh = +125°C
NCV2903 is qualified for automotive use.
3. The maximum output current may be as high as 20 mA, independent of the magnitude of VCC, output short circuits to VCC can cause
excessive heating and eventual destruction.
4. At output switch point, VO1.4 Vdc, RS = 0  with VCC from 5.0 Vdc to 30 Vdc, and over the full input common mode range (0 V to
VCC = −1.5 V).
5. Due to the PNP transistor inputs, bias current will flow out of the inputs. This current is essentially constant, independent of the output state,
therefore, no loading changes will exist on the input lines.
6. Input common mode of either input should not be permitted to go more than 0.3 V negative of ground or minus supply. The upper limit of
common mode range is VCC −1.5 V.
7. Response time is specified with a 100 mV step and 5.0 mV of overdrive. With larger magnitudes of overdrive faster response times are
obtainable.
8. The comparator will exhibit proper output state if one of the inputs becomes greater than VCC, the other input must remain within the common
mode range. The low input state must not be less than −0.3 V of ground or minus supply.

http://onsemi.com
3
 LM393, LM293, LM2903, LM2903V, NCV2903

LM293/393 LM2903
80 80
TA = −40° C
IIB , INPUT BIAS CURRENT (nA)

70

IIB , INPUT BIAS CURRENT (nA)

70
60 60
TA = −55° C
50 50 TA = 0° C
TA = 0° C
40 40 TA = +25° C
TA = +25° C
30 TA = +70° C 30
TA = +85° C
20 20
TA = +125°C
10 10

0 0
0 5.0 10 15 20 25 30 35 40 0 5.0 10 15 20 25 30 35 40
VCC, SUPPLY VOLTAGE (Vdc) VCC, SUPPLY VOLTAGE (Vdc)

Figure 2. Input Bias Current versus Figure 3. Input Bias Current versus
Power Supply Voltage Power Supply Voltage

10 10
Out of Out of
VOL , SATURATION VOLTAGE (Vdc)

VOL , SATURATION VOLTAGE (Vdc)

Saturation Saturation

1.0 1.0
TA = +125°C
TA = +85° C

0.1 0.1
TA = +25° C TA = −55° C TA = +25° C

0.01 0.01
TA = 0° C

TA = −40° C
0.001 0.001
0.01 0.1 1.0 10 100 0.01 0.1 1.0 10 100
ISink, OUTPUT SINK CURRENT (mA) ISink, OUTPUT SINK CURRENT (mA)

Figure 4. Output Saturation Voltage Figure 5. Output Saturation Voltage

versus Output Sink Current versus Output Sink Current

1.0
TA = −55° C TA = −40° C
ICC , SUPPLY CURRENT (mA)

1.2
ICC , SUPPLY CURRENT (mA)

0.8 TA = 0° C
TA = +25° C TA = 0° C
1.0
TA = +25° C
0.6
TA = +70° C 0.8
0.4 TA = +125°C
TA = +85° C
0.6
0.2
RL =  RL = 
0.4
0
5.0 10 15 20 25 30 35 40 0 5.0 10 15 20 25 30 35 40
VCC, SUPPLY VOLTAGE (Vdc) VCC, SUPPLY VOLTAGE (Vdc)

Figure 6. Power Supply Current versus Figure 7. Power Supply Current versus
Power Supply Voltage Power Supply Voltage

http://onsemi.com
4
 LM393, LM293, LM2903, LM2903V, NCV2903

APPLICATIONS INFORMATION

These dual comparators feature high gain, wide The addition of positive feedback (< 10 mV) is also
bandwidth characteristics. This gives the device oscillation recommended. It is good design practice to ground all
tendencies if the outputs are capacitively coupled to the unused pins.
inputs via stray capacitance. This oscillation manifests itself Differential input voltages may be larger than supply
during output transitions (VOL to VOH). To alleviate this voltage without damaging the comparator’s inputs. Voltages
situation, input resistors < 10 k should be used. more negative than −0.3 V should not be used.

+15 V

R1 R4 R5 Vin(min)
220 k 220 k 10 k Vin
8.2 k
Vin 
R1 6.8 k LM393
+VCC 
D1 R2

 10 k
15 k 10 M LM393
Vin VCC
R3

VO 
D1 prevents input from going negative by more than 0.6 V. −VEE
R1 + R2 = R3 
− VEE
R5
R3 ≤ for small error in zero crossing.
10 Vin(min)  0.4 V peak for 1% phase distortion ().

Figure 8. Zero Crossing Detector Figure 9. Zero Crossing Detector

(Single Supply) (Split Supply)

VCC VCC

1.0 M t R RL
VCC
− −
RL LM393 LM393
− 10 k + VC C + VO
VCC 0.001 F LM393
VO
+ + Vref
51 k
‘‘ON’’ for t  tO + t
where: Vin Vref
51 k VCC Vref 0
51 k t = RC n ( ) VO
VCC
VO 0
VC Vref
0 0
t tO t

Figure 10. Free−Running Square−Wave Oscillator Figure 11. Time Delay Generator

VCC

RS = R1 | | R2
RS RL
− (VCC −Vref) R1
Vth1 = Vref +
LM393 R1 + R2 + RL
+
(Vref −VO Low) R1
Vth2 = Vref −
R1 R1 + R2
Vref
R2

Figure 12. Comparator with Hysteresis

http://onsemi.com
5
 LM393, LM293, LM2903, LM2903V, NCV2903

MARKING DIAGRAMS

PDIP−8 Micro8
N SUFFIX DM SUFFIX
CASE 626 CASE 846A
8 8
8 8
LM393N LM2903N x93 2903
AWL AWL
YYWW YYWW AYW AYW

1 1
1 1

SOIC−8
D SUFFIX
CASE 751

8 8 8
LMx93 2903 2903V
ALYW ALYW ALYW
*
1 1 1

x = 2 or 3
A = Assembly Location
WL, L = Wafer Lot
YY, Y = Year
WW, W = Work Week
*This marking diagram also applies to NCV2903DR2.

http://onsemi.com
6
 LM393, LM293, LM2903, LM2903V, NCV2903

ORDERING INFORMATION
Device Package Shipping†
LM293D SOIC−8 98 Units / Rail
LM293DR2 SOIC−8 2500 Units / Reel
LM293DR2G SOIC−8
(Pb−Free)

LM293DMR2 Micro8 4000 Tape and Reel

LM393D SOIC−8 98 Units / Rail
LM393DG SOIC−8
(Pb−Free)

LM393DR2 SOIC−8 2500 Units / Reel

LM393DR2G SOIC−8
(Pb−Free)

LM393N PDIP−8 50 Units / Rail

LM393NG PDIP−8
(Pb−Free)

LM393DMR2 Micro8 4000 Tape and Reel

LM393DMR2G Micro8
(Pb−Free)

LM2903D SOIC−8 98 Units / Reel

LM2903DR2 SOIC−8 2500 Units /Reel
LM2903N PDIP−8 50 Units / Rail
LM2903DMR2 Micro8 4000 Tape and Reel
LM2903VD SOIC−8 98 Units / Reel
LM2903VDG SOIC−8
(Pb−Free)

LM2903VDR2 SOIC−8 2500 Units /Reel

LM2903VDR2G SOIC−8
(Pb−Free)

LM2903VN PDIP−8 50 Units / Rail

NCV2903DR2 (Note 9) SOIC−8 2500 Tape and Reel
NCV2903DR2G (Note 9) SOIC−8
(Pb−Free)

NCV2903DMR2 (Note 9) Micro8 4000 Tape and Reel

9. NCV2903 is qualified for automotive use.

†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.

http://onsemi.com
7
 LM393, LM293, LM2903, LM2903V, NCV2903

PACKAGE DIMENSIONS

PDIP−8
N SUFFIX
CASE 626−05
ISSUE L

NOTES:
1. DIMENSION L TO CENTER OF LEAD WHEN
FORMED PARALLEL.
8 5 2. PACKAGE CONTOUR OPTIONAL (ROUND OR
SQUARE CORNERS).
3. DIMENSIONING AND TOLERANCING PER ANSI
−B− Y14.5M, 1982.

1 4 MILLIMETERS INCHES
DIM MIN MAX MIN MAX
A 9.40 10.16 0.370 0.400
B 6.10 6.60 0.240 0.260
F C 3.94 4.45 0.155 0.175
D 0.38 0.51 0.015 0.020
NOTE 2 −A− F 1.02 1.78 0.040 0.070
L G 2.54 BSC 0.100 BSC
H 0.76 1.27 0.030 0.050
J 0.20 0.30 0.008 0.012
K 2.92 3.43 0.115 0.135
C L 7.62 BSC 0.300 BSC
M −−− 10
−−− 10

J N 0.76 1.01 0.030 0.040
−T−
SEATING N
PLANE
M
D K
H G
0.13 (0.005) M T A M B M

http://onsemi.com
8
 LM393, LM293, LM2903, LM2903V, NCV2903

SOIC−8
D SUFFIX
CASE 751−07
ISSUE AC

NOTES:
−X− 1. DIMENSIONING AND TOLERANCING PER
A ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A AND B DO NOT INCLUDE
MOLD PROTRUSION.
8 5 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)
PER SIDE.
B S 0.25 (0.010) M Y M 5. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
1 PROTRUSION SHALL BE 0.127 (0.005) TOTAL
4 IN EXCESS OF THE D DIMENSION AT
−Y− K MAXIMUM MATERIAL CONDITION.
6. 751−01 THRU 751−06 ARE OBSOLETE. NEW
STANDARD IS 751−07.
G
MILLIMETERS INCHES
C N X 45
DIM MIN MAX MIN MAX
A 4.80 5.00 0.189 0.197
SEATING B 3.80 4.00 0.150 0.157
PLANE
C 1.35 1.75 0.053 0.069
−Z− D 0.33 0.51 0.013 0.020
0.10 (0.004) G 1.27 BSC 0.050 BSC
M H 0.10 0.25 0.004 0.010
H D J J 0.19 0.25 0.007 0.010
K 0.40 1.27 0.016 0.050
M 0
8
0
8

0.25 (0.010) M Z Y S X S N 0.25 0.50 0.010 0.020
S 5.80 6.20 0.228 0.244

SOLDERING FOOTPRINT*

1.52
0.060

7.0 4.0
0.275 0.155

0.6 1.270
0.024 0.050

SCALE 6:1 inches

mm 

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.

http://onsemi.com
9
 LM393, LM293, LM2903, LM2903V, NCV2903

PACKAGE DIMENSIONS

Micro8
DM SUFFIX
CASE 846A−02
ISSUE F
NOTES:
−A− 1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD FLASH,
PROTRUSIONS OR GATE BURRS. MOLD FLASH,
PROTRUSIONS OR GATE BURRS SHALL NOT
K −B− EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE INTERLEAD
FLASH OR PROTRUSION. INTERLEAD FLASH OR
PROTRUSION SHALL NOT EXCEED 0.25 (0.010)
PER SIDE.
5. 846A−01 OBSOLETE, NEW STANDARD 846A−02.
PIN 1 ID
G
D 8 PL MILLIMETERS INCHES
DIM MIN MAX MIN MAX
0.08 (0.003) M T B S A S A 2.90 3.10 0.114 0.122
B 2.90 3.10 0.114 0.122
C −−− 1.10 −−− 0.043
D 0.25 0.40 0.010 0.016
SEATING G 0.65 BSC 0.026 BSC
−T− PLANE H 0.05 0.15 0.002 0.006
C J 0.13 0.23 0.005 0.009
0.038 (0.0015) K 4.75 5.05 0.187 0.199
L 0.40 0.70 0.016 0.028
J L
H

SOLDERING FOOTPRINT*
1.04 0.38
8X 8X
0.041 0.015

3.20 4.24 5.28

0.126 0.167 0.208

0.65
6X
0.0256 SCALE 8:1 inches
mm 

*For additional information on our Pb−Free strategy and soldering

details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.

Micro8 is a trademark of International Rectifier.

ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.

PUBLICATION ORDERING INFORMATION

LITERATURE FULFILLMENT: N. American Technical Support: 800−282−9855 Toll Free ON Semiconductor Website: http://onsemi.com
Literature Distribution Center for ON Semiconductor USA/Canada
P.O. Box 61312, Phoenix, Arizona 85082−1312 USA Order Literature: http://www.onsemi.com/litorder
Phone: 480−829−7710 or 800−344−3860 Toll Free USA/Canada Japan: ON Semiconductor, Japan Customer Focus Center
Fax: 480−829−7709 or 800−344−3867 Toll Free USA/Canada 2−9−1 Kamimeguro, Meguro−ku, Tokyo, Japan 153−0051 For additional information, please contact your
Email: [email protected] Phone: 81−3−5773−3850 local Sales Representative.

http://onsemi.com LM393/D
10
This datasheet has been download from:

www.datasheetcatalog.com

Datasheets for electronics components.