0% found this document useful (0 votes)
429 views5 pages

Cisco Switch Commands Cheat Sheet

This document provides a cheat sheet of commands for configuring Cisco switches using both IOS and CLI interfaces. It lists commands for settings like the hostname, passwords, remote access, CDP, port descriptions, port speeds, duplex settings, static VLANs, trunk ports, VTP, STP, portfast, and uplinkfast. The document also provides contact information for a Cisco networking equipment wholesaler.

Uploaded by

Shreeram Rane
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
429 views5 pages

Cisco Switch Commands Cheat Sheet

This document provides a cheat sheet of commands for configuring Cisco switches using both IOS and CLI interfaces. It lists commands for settings like the hostname, passwords, remote access, CDP, port descriptions, port speeds, duplex settings, static VLANs, trunk ports, VTP, STP, portfast, and uplinkfast. The document also provides contact information for a Cisco networking equipment wholesaler.

Uploaded by

Shreeram Rane
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Cisco switch commands cheat sheet

Cisco commands cheat sheet for switch:


1Setting hostname based on the IOS switches:
Switch (config hostname hostname) #
Setting system name based on the CLI switches:
Switch (enable) set system name name-string

2 Setting password based on the IOS switches:


Switch (config) enable password level 1 password #
Setting password based on the CLI switches:
Switch (enable) set password
Switch (enable) set enalbepass

3 Setting the remote access based on the IOS switch:


Switch (config) interface VLAN 1 #
Switch (config-if) IP address IP-address netmask #
Switch (config-if) IP default-gateway IP-address #
Setting the remote access based on the CLI switch:
Switch (enable) set interface sc0 IP-address netmask broadcast-address
Switch (enable) set interface sc0 VLAN
Switch (enable) set IP route default gateway

4 Enabled and browsing information of CDP based on the IOS switch :


Switch (config-if CDP enable) #
Switch (config-if) no CDP enable #
In order to view the Cisco CDP announcement adjacent equipment:
Switch# show CDP interface
Switch# show cdp neighbors
Enabled and browsing information of CDP based on the CLI switch :
Switch (enable) set CDP {enable|disable} module/port
In order to view the Cisco CDP announcement adjacent equipment:
Switch (enable) show cdp neighbors

5 Port description based on the IOS switch:

1
Switch (config-if description description-string) #
Port description based on the CLI switch:
Switch (enable) set port name module/number description-string

6 Setting port speed based on the IOS switches:


Switch (config-if) # speed{10|100|auto}
Setting port speed based on the CLI switches:
Switch (enable) set port speed moudle/number {10|100|auto}
Switch (enable) set port speed moudle/number {4|16|auto}

7 Setting the ethernet link pattern based on the IOS switch:


Switch (config-if duplex {auto|full|half}) #
Setting the ethernet link pattern based on the CLI switch:
Switch (enable) set port duplex module/number {full|half}

8 Configuring the static VLAN based on IOS switch:


Switch# VLAN database
Switch (VLAN) VLAN vlan-num name VLA #
Switch (VLAN) # exit
Switch# configure teriminal
Switch (config) interface interface module/number #
Switch (config-if) switchport mode access #
Switch (config-if) switchport access VLAN vlan-num #
Switch (config-if) # end
Configuring the static VLAN based on CLI switch:
Switch (enable) set VLAN vlan-num
Switch (enable) set VLAN vlan-num mod-num/port-list

9 Configuring the VLAN relay line based on IOS switch:


Switch (config) interface interface mod/port #
Switch (config-if) switchport mode trunk #
Switch (config-if) switchport trunk encapsulation {isl|dotlq} #
Switch (config-if) switchport trunk allowed VLAN remove vlan-list #
Switch (config-if) switchport trunk allowed VLAN add vlan-list #

2
Configuring the VLAN relay line based on CLI switch:
Switch (enable) set trunk module/port
Vlan-range

10 Configuring VTP management domain based on the IOS switch:


Switch# VLAN database
Switch (VLAN) VTP domain domain-name #
Configuring VTP management domain based on the CLI switch:
Switch (enable) set VTP

11 Configuring VTP mode based on the IOS switch:


Switch# VLAN database
Switch (VLAN) VTP domain domain-name #
Switch (VLAN VTP {sever|cilent|transparent}) #
Switch (VLAN) VTP password password #
Configuring VTP mode based on the CLI switch:
Switch (enable) set VTP

12 Configuring the VTP version based on the IOS switch:


Switch# VLAN database
Switch (VLAN VTP v2-mode) #
Configuring the VTP version based on the CLI switch:
Switch (enable) set VTP V2 enable

13 Starting the VTP tailoring based on the IOS switch:


Switch# VLAN database
Switch (VLAN VTP pruning) #
Starting the VTP tailoring based on the CLI switch:
Switch (enable) set VTP pruning enable

14 Configuring Ethernet channel based on the IOS switch :


Switch (config-if) port group group-number #
Configuring Ethernet channel based on the CLI switch :
Switch (enable) set port channel moudle/port-range mode{on|off|desirable|auto}

3
15 Adjusting the root path cost based on the IOS switches:
Switch (config-if) spanning-tree cost cost #
Adjusting the root path cost based on the CLI switches:
Switch (enable) set spantree portcost moudle/port cost
Switch (enable) set spantree portvlancost moudle/port

16 Adjusting the port ID based on the IOS switches:


Switch (config-if spanning-treeport-priority port-priority) #
Adjusting the port ID based on the CLI switches:
Switch (enable) set spantree portpri {mldule/port}priority
Switch (enable) set spantree portvlanpri {module/port}priority

17 Setting the STP clock based on IOS switch:


Switch (config) spanning-tree hello-time seconds #
Switch (config) spanning-tree forward-time seconds #
Switch (config) spanning-tree max-age seconds #
Setting the STP clock based on CLI switch:
Switch (enable) set spantree Hello interval
Switch (enable) set spantree fwddelay delay
Switch (enable) set spantree maxage agingtiame

18 Enable or disable the Port Fast feature based on the IOS switch port:
Switch (config-if) #spanning-tree portfast
Enable or disable the Port Fast feature based on the CLI switch port:
Switch (enable) set spantree portfast {module/port}{enable|disable}

19 Enable or disable the UplinkFast feature based on the IOS switch port:
Switch (config spanning-tree uplinkfast) #
Enable or disable the UplinkFast feature based on the CLI switch port:
Switch (enable) set spantree uplinkfast {enable|disable}

More related:
How To Recover Cisco Router Password

4
The Difference of The Cisco Catalyst 2900 and Cisco Catalyst 1900
More Cisco products and Reviews you can visit: http://www.3anetwork.com/blog

3Anetwork.com is a world leading Cisco networking products wholesaler, we wholesale


original new Cisco networking equipments, including Cisco Catalyst switches, Cisco
routers, Cisco firewalls, Cisco wireless products, Cisco modules and interface cards
products at competitive price and ship to worldwide.
Our website: http://www.3anetwork.com
Telephone: +852-3069-7733
Email: [email protected]
Address: 23/F Lucky Plaza, 315-321 Lockhart Road, Wanchai, Hongkong

You might also like